7R Beam230
Touch screen beam light user manual
General information
Safety instructions
Performance trait and skill specifications
DMXS12 signal connection
The installation of the light bulb:
Display Keys
DMX Channel
Cleaning and maintenance
1.General_ information
1.Congratulations, you have just purchased one of the most reliable beam light on the market today.
2,Please read and understand the instructions in this manual carefully and thoroughly before
attempting to operate this unit. These instructions contain important information regarding safety during use and
maintenance.
Notice:
1.As part of our ongoing commitment to continuous products update, company will keep the right to improve this products,
the information in this menu may be changed in the future, the company reserve the right to change the data without any
advises.
Unpacking
1.Thank you for purchasing our company products. Every product has been thoroughly tested and has been shipped in
perfect operating condition.
2.Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be
damaged, carefully inspect your fixture for damage and be sure all accessories necessary to operate the fixture have
arrived intact. In the event damage has been found or parts are missing, please contact our customer support team for
further instructions,
.nside the box you should find: the 230W Beam , clamp, a power cable, and this user manual.
2. Safety instructions
Notice: To guarantee proper and consistent operation, itis important to follow the guidelinesNe emmmemeenssnn amma naa
sh tris manual. Our company will not accept responsibilty for damages resulting from the
misuse ofthis fixture due to the disregard of the information printed in this manual
‘Please check the voltage, frequency data of power supply system is suitable for the mentioned on the beam light
Please do avoid the different voltage between them and burn the beam light
2 Do not attempt to operate this fixture ifthe power cord has become damaged or frayed
3.Never open this fixture while in use.
++ Never look directly into the ight source. You risk injury to your retina, which may induce blindness,
+ Please be aware that damages caused by modifications to the device are not subject 10 Warranty.
43.Performance trait and skill specifications
4, Light source: Osram 7R lamp
2. Channel mode:17,20.16.18-"~" international standard DMXS12 channel
3, Horizontal scan:540 degree(16 BIT precision scan) Electronic error correction
«+ Vertical scanning:270 degree(16 BIT precision scan) scanning electronic error correction
5. Beautiful dot matrix display four light touch switch ,can reverse 180 degrees display
6. Color wheel: color whee! plate ,each color plate is made of 14 color piece
7. Gobos wheel °17 gobos effect
8. Effect wheela rotation eight prism,effect remove, frost effect
9, 0-100% mechanical dimmer,support mechanical stroboscopic and can speed stroboscopic effects support frequency
macro function Beam angle:0-4degree
10. Overheating protection
41. Voltage: 100-220V, S0/60hz
42. Power:350W 13. IP protection grade:IP 20
44, Inductance rectifier and AC/DC inductance rectifier
45. Garon size:40*32"49CM _flightcase size:77*47*70CM(One case pack two)
46. Net weight:17.5KG/UNIT
4.DMX512 signal connection:
‘The lamps and lantems use DMX512 signal control model, the control signal of lamps and lanterns is @ parallel
relationship, the connection is more than one signal lamps and lanterns, its best 1 US double core shielded cables.
‘Connection, all through the lamps and lanterns of lamps and lanterns DMX signal on jack (context) INPUT (INPUT) and
OUTPUT (OUTPUT) are connected, connect the line of lamps and lanterns of 3 core XLRXL plug terminal
Must correspond to each other, when the connection signal lamps and lanterns, itis recommended to use DMX signal
terminal. Can be avoided, due to the electrical noise
‘And cause damage control signal, DMX signal terminal device is a XLR plugs connection between 2 and 3 feet a 120
chm resistance of 1 w, and connect it on the last stage of lamps and lanterns of the OUTPUT (OUTPUT) jack.
§5.The installation of the light bulb:
4. Installing a replacement bulbs, disconnect the lamp holder first plastic shell
2: Itis recommended to use good quality bulbs.
3. Do not charged installation, remove the light bulb.
4, The bal part of the hand do not touch the bulb
5. After the replacement bulbs, must tighten the screw.
Light Bub work at high temperature, and gas discharge can nt continue to Supply the physical characteristics of foam, 50
aa esvat in everytime, when the power is completely cootng bility to operate in about 10 minutes, olhenwse it will lead
to high voltage discharge, short circuit bum out components on the computer consoleSalety tips! In order to ensure the correct use of lamps and lanterns of your safely, Please before use, carefully read the
following safety tips, lest produce unnecessary malfunction and damage
+ Non-speciaists, do not do STH without authorization remove the lamps and lanterns and lamps and lanterns of
accessories.
2. After the replacement bulbs, must tighten the screw.
5 The light bulb work at high temperature, and gas discharge can not continue to supply the physical characteristics of
bubble, 60 you must in every time, when the power is completely cooling abit to operate in about 10 minutes, otherwise
itwil lead to high voltage discharge, short circuit ur out components on the computer console
Safety tps! In order to ensure the correct use of lamps and lanterns of your safety, Please before use, carefully read the
following safety tips, lest produce unnecessary maifunction and damage
+. Non-speciaists, do not do STH without authorization remove the lamps and lanterns and lamps and lanterns of
accessories,
3 The AG power supply: home to check the power supply is inline with the product rated voltage requirements.
5 The lamps and lanterns is according to the type of electric shock protection design, lamps and lanterns should be used
“sth sufficient power supply system grounding, and lamps and lantems of the ground wire must be connected to the
ground ofthe power supply system. Do not use insulation damaged power cord, at the same time, do not use the power
cord overiap on the other wie.
4. When installation location and lamps and lanterns, any point onthe surface of lamps and lanterns and any easy to burn
the explosive Keep minimum distance of 10 meters, 2.6 meters from Irradiation distance, please don't directly installed in
the lamp to burn the material surface.
5. Using the environment temperature of lamps and lanterns: - 10 + 40 degrees), the highest surface temperature of 80
degrees, lamps and lanterns of lamps and lanterns to stay away from Iquid substances and damp environment.
6, Before you use the lamps and lantems must ensure the grounding of lamps and lanterns '§ good, not charged to install
and remove any parts of lamps and lanterns.
F vnstal larmps and lanterns, fied sorew must be tightened, and with addition of safety tine, ané check regularly.
8. Lamps and lanterns of continous worktime and not more than 10 hours, lamps and lanterns of consecutive start time
interval should be not less than 10 points, Otherwise it will not tigger properly because of the light bulb overheating
protection.
9. Inuse process, such as abnormal lamps and lanterns should stop using the lamps and lanterns in ¢ timely manner
10. The service life of the bub to achieve the rated should change in time, can appear otherwise blow bubble of
dangerous accidents.
“1, Lamps and lanterns of rotatonal parts and paste accessories must be inspected regularly, become loose, rock
reinforcement in time, in case of an accident.
‘The lamps and lanterns USES is strong wind cooling, accumulate dit easy, must per month on 8 clean, especially
cooling Gruyere, otherwise youll be in a dust jam, lead to bad heat dissipation, the lamps and lanterns is abnormal
6.Display Keys: