Professional Documents
Culture Documents
NSK
The programmer connects to a host computer using a standard RS232 serial port. All the programming “intelligence” is built
into the programmer so you do not need any special hardware to run it. Programmer comes with window based software for
easy programming of the devices supports in Win 9x,2000,Xp,WinMe. This Programmer Supportrs 89C51,89C52,89C55
89S51,52,8252
YOU CAN CONNECT THROUGH USB PORT USING OUR USB TO UART CONTROLLER KIT NO -12.5
1.3 - Packaging
Simple to use & low cost, yet powerful flash microcontroller programmer for the Atmel 89 series. It will Program, Read and Verify Code
Data, Write Lock Bits, Erase and Blank Check. All fuse and lock bits are programmable.
It can be used with any type of computer and requires no special hardware. All that is needed is a PARALLEL communication port which all
computers have.
The programmer connects to a host computer using a standard Parallel port. All the programming “intelligence” is built into the programmer
so you do not need any special hardware to run it. Programmer comes with window based software for easy programming of the devices
supports in Win 9x,2000,Xp,WinMe.Programmer is Built in power supply , The programmer consists of both 40pin&20pin Zip socket for
40pin&20pin IC respectively
DEVICES SUPPORTED
AT 89C51,AT89C52,AT89C55,AT89C55WD,AT89C1051,
AT89C1051U,AT89C2051,AT89C4051,AT89S51,89S52
AT89S53,AT89S8252,AT89C51RC,D87C51,D87C52
i1
1.3 - Packaging
Simple to use & low cost, yet powerful flash microcontroller programmer for the PIC series. It will Program, Read and Verify
Code Data, Write Lock Bits, Erase and Blank Check. All fuse and lock bits are programmable. This programmer has intelligent
onboard firmware and connects to the serial port. It can be used with any type of computer and requires no special hard-
ware. All that is needed is a serial communication port which all computers have.All devices have signature bytes that the
programmer reads to automatically identify the chip. No need to select the device type – just plug it in and go! All devices
also have a number of lock bits to provide various levels of software and programming protection. These lock bits are fully
programmable using this programmer. Lock bits are useful to protect the progam to be read back from microcontroller only
allowing erase to reprogram the microcontroller.
The programmer connects to a host computer using a standard RS232 serial port. All the programming “intelligence” is built
into the programmer so you do not need any special hardware to run it. Programmer comes with window based software for
easy programming of the devices supports in Win 9x,2000,Xp,WinMe.
12C508,508A,509,509A,671,672,10F200,202,204,206,12CE518,519,673,674,12F675,629,635,683,16C433,54,56,58,61,62A,62B,63,63A,64A,65A,65B,66,67,71,
16C72,72A,73A,73B,74A,74B,76,77,84,505,620,620A,621,16C621A,622,622A,711,712,715,716,717,745,765,770,771,16C773,774,781,782,923,924,16CE623,624,625,
16F72,73,74,76,77,83,84,84A,88,627,628A,630,648A,676,16F818,819,870,871,872,873,873A,874,874A,876,876A,877,877A
18F242,248,252,258,442,448,452,458,1220,1320,2320,2220.4220,2331,2431,18F4431,4320,4539,6620,6720,8620,8720,6520,8520,2410,2420,2455,2480,
2510,2515,2520,2525,2550,2580,2585,2610,2620,2680,4410,4420,4455,4480,4510,4515,4520,4525,4550,4580,4585,4610,4620,4680,
PIC PROG
1.3 - Packaging
Simple to use & low cost, yet powerful flash microcontroller programmer for the PIC series. It will Program, Read and Verify
Code Data, Write Lock Bits, Erase,and Blank Check,Auto programming mode - this allows you to program chips without
having to touch the Windows interface.When active, the software will detect when a chip is inserted into the socket and
automatically commence the program/verify process.Once the chip is programmed, the software will wait until the next chip
is inserted before programming continues.
All fuse and lock bits are programmable. This programmer has intelligent onboard firmware and connects to the USB port
As a virtual COM prot . It can be used with any type of computer and requires no special hardware. All that is needed is a
USB communication port which all computers have.All devices have signature bytes that the programmer reads to automati-
cally identify the chip. No need to select the device type – just plug it in and go! All devices also have a number of lock bits to
provide various levels of software and programming protection. These lock bits are fully programmable using this program-
mer. Lock bits are useful to protect the progam to be read back from microcontroller only allowing erase to reprogram the
microcontroller.
The programmer connects to a host computer using a standard USB port. All the programming “intelligence” is built into the
programmer so you do not need any special hardware to run it. Programmer comes with window based software for easy
programming of the devices supports in Win 9x,2000,Xp,WinMe.
1.3 - Packaging
The MPLAB ICD 2 is a low-cost in-circuit debugger (ICD) and in-circuit serial programmer
(ICSP). MPLAB ICD 2 is intended to be used as an evaluation, debugging and programming aid
In a laboratory environment. The MPLAB ICD 2 offers these features:
· Real-time and single-step code execution
· Breakpoints, Register and Variable Watch/Modify
· In-circuit debugging
· Target Vdd monitor
· Diagnostic LEDs
· MPLAB IDE user interface
· RS-232 serial interface to a host PC
1.3 - Packaging
2. Features
3. Specifications
AT90S8534,8544,1200,2313,2323,2333
AT90S2343,4414,4433,4434,8515,8535
ATMEGA 103,128,16,161,163,169,32,
ATMEGA 603,64,8,83,8515, 8535,
AT TINY 12,15,19,26,28
AT90S1200,2313,2323,2343,4414,4433,4434,8515,8535,
ATMEGA103,128,1280,1281,16,161,162,163,165,168,169,
ATMEGA 2560,2561,32,323,325,3250,329,3290,406,48,64
ATMEGA 640,644,645,6450,649,6490,8,8515,8535,88
ATTINY 11,12,13,15,22,2323,25,26,261,28,44,45,461,84,85,86
AT90CAN128,32,64 - AT90PWM2,3
Packaging
SEEPROM PROGRAMMER
Introduction
Serial eeproms are finding more and more use in electronic devices these days.
These small 8 pin devices offer non-volatile data storage and require minimal I/O
lines to connect to them. This makes them ideal in many microcontroller based
applications.
The programmer connects to the PC Serial port and is controlled by driver software
running on the PC. The software is Windows based will run under Windows9X,
2000&XP
EEPROMS SUPPORTED
I(2)C EEPROM SDA2526
24C01A SDA2546
24C02 SDA2586
24C04 SDA3506
24C08 SDA3516
24C16 SDA3526
24C32 MICROWIRE EEPROM
24C64/65 (Atmel) 93C06,93C14,93C46,93C57,93C56,93C66,93C76.93C86
AT24C128 (Atmel)
AT24C256 (Atmel)AT24C512 (Atmel) M24C128 (Microchip)M24C256 (Microchip)
24C515 (Microchip) , SDA2506 ,2516,
1. Board Features:
1. LPC 2129 Single-chip 16/32-bit microcontrollers 256KB Flash/128KB RAM
2. 4 Channel 10-bit ADC
3. 7-Segment LED Display(Multiplexed x4)
4. 2 CAN Ports with 2CAN TransRecivers
5. A Serial Port for ISP
6. An RS232 Serial Port
7. On Board JTAG Wiggler for Debugging
8. DC Power Supply Connector(12v Ac or Dc)
9. Optional USB Socket for Power Supply
10. LCD display 2linex16Character
11. 24Cxx I2C EEPROM
12. 8 LED array
13. Matrix Key Pad
14. 4 Intruupt Switches
15. Buzzer
Board Features:
1. On board Regaulated Power supply
2. Input Power supply - 12v AC or DC
3. A 7-Segment LED Display(Multiplexed x4)
4. An RS232 Serial Port
5. LCD display(optional)
6. 24Cxx I2C EEPROM
7. RTC DS 1302
8. Matrix Key Pad
9. 4 Intruupt Switches
10. Output 5v,12v,GND
11. 8 LED array
12. ULN 2003 high current driver
The DT125R series RFID Proximity OEM Reader Module has a built-in antenna in minimized form factor.
It is designed to work on the industrystandard carrier frequency of 125 kHz.
This LF reader module with an internal or an external antenna facilitates communication with Read-Only
transponders—type UNIQUE or TK5530 via the air interface. The tag data is sent to the host systems
via thewired communication interface with a protocol selected from the modulepinout.
The LF DT125R module is best suited for applications in Access Control,Time and Attendance, Asset
Management, Handheld Readers,Immobilizers, and other RFID enabled applications.
Features
Introduction
This document describes the hardware interface of the SIMCOM SIM300 module that
connects to the specific application and the air interface. As SIM300 can be integrated
with a wide range of applications, all functional components of SIM300 are described in
great detail.
Product concept
Designed for global market, SIM300 is a Tri-band GSM/GPRS engine that works on
frequencies EGSM 900 MHz, DCS 1800 MHz and PCS 1900 MHz. SIM300 features GPRS
multi-slot class 10/ class 8 (optional) and supports the GPRS coding schemes CS-1, CS-
2, CS-3 and CS-4.
Board Features:
1. On board Regaulated Power supply
2. Input Power supply - 12v AC or DC
3. A 7-Segment LED Display(Multiplexed x4)
4. An RS232 Serial Port
5. LCD display 2linex16Character
6. 24Cxx I2C EEPROM ,ULN 2003 high current driver
7. RTC DS 1302
8. Matrix Key Pad
9. 4 Intruupt Switches
10. Output 5v,12v,GND
Package Contents:
1. 8051 evaluation board
2. CD containing(Softwares,Example Programs)
3. Burg Connectors 20 Nos
Nsk Electronics , India ©Copyright 2007,All Right Reserved
http://www.nskelectronics.com
NSK I/O INTERFACE BOARDS
12.1 - 4X4 MATRIX KEYPAD 12.2 - MULTIPLEXED7 SEG DISPLAY
(com cathode)
12.7 - 8 CHANNEL RELAY CONTROL BOARD 12.8- LCD DISPLAY INTERFACED BOARD WITH 8 O/P
with Power Supply & ULN 2003 I/P HIGH CURRENT DRIVER USING ULN 2003 ,8 I/P
& RS -232 CONVERTER
The Mini PLC is fully isolated with opto couplers Inputs may be from 5v to 12 volts
(under request 24v) . the Outputs will be 12 or 5 VDC (100 MA)
This board is very useful for mini Automation .Regulated power supply is Built in
The A/D Stepper Motor Controller IC1 generates four phase drive signals
for two phase bipolar and four phase unipolar step motors in microcontroller
controlled applications. The motor can be driven in half step, normal and
wawe drive modes and on-chip PWM chopper circuits permit switchmode
control of the current in the windings. A feature of this device is that it
requires only clock,direction and mode input signals. Since the phase are
generated internally the burden on the microcontroler and the programmer
is greatly reduced. IC2 is a monolithic bridge high current driver
Specifications:
Contact information
NSK Electronics
No 66/3 , Sabari Complex
S.P. Road , Bangalore - 560 002
Karnataka , India