You are on page 1of 6

1. Oscilloscope is a---------------measuring device?

A) Current B) Frequency C) Voltage D) None of these

Superposition Theorem. The total current in any part of a linear circuit equals the
algebraic sum of the currents produced by each source separately. To evaluate the
separate currents to be combined, replace all other voltage sources by short circuits
and all other current sources by open circuits.
2. In superposition theorem voltage sources are converted into-----------circuit?
A)Open B) Short C) Current Source D) None of these
3. ------------- phase like 3 phase provide constant power transfer to linear loads?
A)Single B) 02 C) Poly D) HV DC
4. Super position theorem converts a circuit into its --------- equilent?
A)Norton B) Thevenin C)Both D) None Of these
5. In IM requirement of variable speed can be met by using-------------?
A)Variable Freq device B)Wound rotor C)Traction Motor D) Shunt motor
6. Transformer are designed to have----------leakage inductance?
A)zero B) Low C) High D) Unity
7. Difference between synchronous speed and----------speed is called slip?
A)Shunt B) Series C) Actual Or Rotor D)None
8. Fourier transform imposes---------parity to fourier cosines ?
A)Odd B) Even C) Negative D) None
A Clamper Circuit is a circuit that adds a DC levelto an AC signal. Actually, the positive
and negative peaks of the signals can be placed at desired levelsusing the clamping
circuits. As the DC level gets shifted, a clamper circuit is called as a Level Shifter
9. Clamping circuit adds------------level?
A)AC B) DC C) Smooth D) None
10. Device used to measure refraction of Eye is called--------? retinoscope
A)Drumometer B) Ellipsograph C) Dioptometer D)None
11. CRO has two calibrations volt/div and------------------? Horizontol time division
A)Freq/Div B) Current/Div C) Time/Div D)None
The full version of Ampere's Law is one of Maxwell'sEquations that describe the
electromagnetic force.Ampere's Law specifically says that the magnetic field created by
an electric current is proportional to the size of that electric current with a constant of
proportionality equal to the permeability of free spac e
Ampere's Law states that for any closed loop path, the sum of the length elements times
the magnetic field in the direction of the length element is equal to the permeability times
the electric current enclosed in the loop
12. Ampere circuital law is electrically equilent to ---------- law?
A) Lens B)Biot-Savarts C)Faraday D) Gauss
13. Current density of armature winding in DC motors is in the range of--------? 15 to
20m A
A) 1 amp-5 amp B)10 amp-20amp C) 20amp-30amp D) None
14. which cell is rechargeable ?
A)Primary B) Secondary C) Galvanic D) None
15. If current is decreased by 2% then power decreases by---------%? Voltage drop
cause 4 percent
A)2 B)4 C)8 D) 16
16. 33Kv-66Kv is referred as-----------transmission voltages?\
A)Primary B) Secondary C) Variable D) None
Transverse waves that exhibit polarization includeelectromagnetic waves such as light
and radio waves, gravitational waves, and transverse soundwaves (shear waves) in
solids. ... Polarized light can be produced by passing unpolarized light through a
polarizer, which allows waves of only onepolarization to pass through.
17. Polarization is caused by---------------nature of EM waves?
A)Longitudinal B)Transverse C) Reflex D) None
Construction and Operation of DIAC. Basically, the DIAC is a two terminal device; it is a
combination of parallel semiconductor layers that allows activating in one
direction.This device is used to activating device for the triac. Four layer PNPN
18. DIAC is a-----------terminal-----------layer device?
A) 02,04 B)03,02 C)02,03 D)02,05
19. Electric lines of force tends to---------------------- each other?
A)Move Parallel to B) Move Orthogonal to C) Move Away from D)None
20. Critical value of resistance in large transmission lines is------------ohm?
A)500 B)1000 C)2000 D)None
21. Thermal power station moderate------------kv?
A)11 B)33 C)66 D)None
The energy efficiency of a conventional thermal power station, considered
salable energy produced as a percent of the heating value of the fuel consumed, is
typically 33% to 48%.
22. Efficiency of thermal power station is-----------%?
A)33 B)40 C)50 D)60
23. Insulation in high voltage transmission is--------type?
A)Pin B)Disk C)Suspension D)None
24. Above 220Kv transmission line is called-----------?
A)Moose (400kv) B)Zebra C)Panther(132kv) D)Dog(66KV)
Diversity is usually more than one. Demand factor is the ratio of the sum of the maximum
demand of a system (or part of a system) to the total connected load on the system (or
part of the system) under consideration. Demand factor is alwaysless than one
25. Diversity Factor of a group is always----------?
A)Unity B)Zero C)Greater than 1 D)Less than 1
26. Load factor is given by --------?
A)max load/avg load B)Avg load/max load C)Avg load/Connected load D)None
27. Minimum Transmission voltage is------------KV?
A)33 B)66 C)110 D)120
28. Active devices are those which --------------?
A)Delivers power B) Absorbs power C) Both D)None
29. If electrons are moving towards the +ve terminal then power is --------------?
A)Delivered B)Absorbed C)Both D)None
30. In IM when air gap increases then the short circuit current----------------?
A)Decreases B)Increases C)Remain the same D)First increases then decreases
31. Simplest active device is-------------------?
A)Inverting amp B)Non inverting amp C)Half wave rectifier D)Full wave rectifier
32. Rectifier using Oscilloscope to stop diode drop is called------------rectifier?
A)Active B)Passive C)Saturating D) Non-Saturating
33. For non repetitive signals--------------transform is used?
A)Fourier B)Wavelet C)Laplace D)Z-
A linear system is BIBO stable if its characteristic polynomial is stable. The
denominator is required to be Hurwitz stable if the system is in continuous-time and
Schur stable if it is in discrete-time. In practice, stability is determined by applying any
one of several stability criteria.
34. For discrete stability of characteristic polynomial equation,--------- method is
used?
A)Nyquest B)Hurwitz C)Bode plot C)Root locus
35. Delta service is cheap because of----------------?
A)No Ground Wire B)No Neutral wire C)No Phase wire D)No Line wire
36. In Analog intensity modulation,-----Rectifier using Rectifier using ----------applied
to the LED is increased?
A)Current B)Voltage C)Frequency D)Amplitude
37. For Multiple video channels, --------- diodes are required?
A)Zener B)LED C)Schottky D)None
38. Logic gates are made of-----------?
A)Diodes B)Simple Transistor C)FET D)None
39. For 02 inputs, ----------- Boolean functions are required ?
A)04 B)02 C)08 D)16
40. Advantages of open loop system are simplicity & ---------- ?
A)Construction (COST) B)Noise Reduction C)Accuracy D)Reliability
41. Open loop system is also called------------?
A)Manual B)Automatic C)Stable C)Passive
42. Circuit Breakers-----------on fault detection?
A)Opens B)Closes C)No Action D)Triggers alarm
43. Curl of a vector is ------------?
A)Vector B)Scalar C)Gradient of That vector D)All of the above
44. Voltage is closed -------------integral of E?
A)Surface B)Line C)Volume D)Area
45. Aero turbine don't have ---------?
A)Stator B)Compressor C)Fan D) Fuel Intake System
46. Disadvantages of non inverting amplifier is -------------?
A)Limited speed B)Noise (Distortion) C)Error D)Unpredictability
47. Voltage is a Difference between -------------- Pressure?
A)Magnetic B)Electric C)Ohamic D)Lorentz
48. For zero surface charge density, normal component of -------------- is continuous?
A)EMF B)MMF C)EF Intensity D) MF Intensity
49. Number of state variables are ------------ the order of the Differential equation?
A)Greater Than B)Equal To C)Smaller Than D)None
50. Resistivity of a material depends on----------?
A)Length B)Area C)Material D)None
See,when one leg of a star connected circuit is made open,i.e., it offers infinite
resistance.

•Here the assumption i have made is that LOAD IS BALANCED. And there in
current in the neutral circuit.
•Initial power when the circuit was balanced was= 3Vph*Iph*cosphi=3/root3
*VL*IL *cosphi.
•Because phase voltage in star circuit is 1/root 3 times Line to line voltage.
•Now when one leg is removed the power consumed would be
=2Vph*Iph*Cosphi=2/root3 *VL*IL* Cosphi=
51. When a resistor is removed from star connection, total power ------------?
A)Reduce by Under root 3 B)Increase by Under root 3 C)Remain the same D)None
Holding current. It is defined as the minimum anode currentbeyond SCR turns off.
The holding current is associated with turned off process. The holding current is always
less than thelatching current.
52. Holding current is--------------latching current?
A)3 Times B)1/3 times C)2 Times D)1/2 Times
A stepper motor or step motor or stepping motor is a brushless DC electric motor that
divides a full rotation into a number of equal steps.
53. Stepper motor is a ------------- Motor?
A)DC B)AC C)Synchronous D)None
54. O/P voltage in voltage dividing rule is---------------?
A)R1/R2 B)(R1+R2)Vin/R1 C)R1 Vin/(R1+R2) D)None
55. Cu oxide ------------- is used for passing currents through meter in one direction?
A)Transistor B)Diode C)Voltmeter C)Rectifier E)Diac
56. Match Filter is used to improve ----------?
A)Impedance Matching B)SNR C)BER D)Design
57. Ipv4 is a -------------bits?
A)8 B)16 C)32 D)24
58. Diff Amp is basically used as -------------?
A)Current amp B)BW amp C)Push Full amp D)Voltage amp
59. Coupling used in Diff Amp is-------------- coupling?
A)RC B)Direct C)RL D)Transformer
60. In closed loop transient function, different variables are represented as ---------?
A)Scalar B)Vector C)Arrow diagram D) None
61. Impedance is given by -----------?
A)R/L B)R/C C)Phasor V/ Phasor I
62. In OSI Model Link layer is also called ----- Layer?
A)Network B)Transport C)Physical D)None
63. Natural Uranium contains ---------------% U235?
A)Zero B)0.2 C)0.5 C)0.7
64. Green function is used to solve ----------- order differential equation?
A)1st B)2nd C)3rd D)4th
Of electron emitted is depends on intensity of light and speed of Electron isdepends on
frequency of incidents light. Photoelectric current is due to the ejection of photo
electrons. And the ejection of electrons from the metal surface dependsupon the
intensity of the incident radiation.
65. Emission of photo electrons depends on -------------- of light?
A)Wavelength B)Frequency C)Intensity D)None
66. Voltages above 230 kV are considered as -------------voltages?
A)High B)Low C)Extra High D)None
67. Lactometer is used to find specific gravity of milk and ----------- in Milk?
A)Impurity B)Water C)proteins D)None (Density is best suitable if given)
The Wheatstone bridge is a null measurement device for calculating resistance by
balancing potential drops in a circuit. (See Figure 4.) The device is called a bridge
because the galvanometer forms a bridge between two branches. A variety of
bridge devices are used to make null measurements in circuits
68. Null detector used in Wheat Stone bridge is a/an
A) Ammeter B) Voltmeter C) Galvanometer D) Wattmeter
69. A signal can be reconstructed from its samples if the sampling period is...........
the signal period
A) Equal B) Twice C) Thrice D) Half
70. There are 02 types of over current protections, Instantaneous over current
and .................... over current?
A)Variable Time B)Constant (Definite) Time C)Delay feedback D)None
71. Which of the following is not a purpose of disturbance monitor?
A) Model Validation B)Disturbance Investigation C)Increase Protection Settings
D)Assessment Of performance
72. ............ voltage is a small voltage (less than 10) that can be measured between
two points ?
A)Dim B)Tame C)Stray D)Ground
73. .............. is used to sense fault and initiate a trip?
A)Circuit Breaker B) Alternator C)Protection Relay D)Cut Outs
74. The Principal of ............ can be used to analyze faults in power systems?
A)Thevenin B)Norton C)Superposition D)Jordon
75. The ripple frequency for bridge rectifier is.....................?
A)Same as I/P B)Twice of I/P C)Half of I/P D)None
76. For conversion high impedance to low impedance .................. amplifier is used?
A)Inverting B)Non Inverting C)Summation D)Voltage Follower
77. It is desirable to avoid differentiator because,................?
A)It is costly B)It High Impedance C)It creates Noise/Distortion D)None
A stepper motor is a brushless, synchronous electric motor that converts digital pulses into
mechanical shaft rotation. Every revolution of the stepper motor is divided into a discrete number
of steps, in many cases 200 steps, and the motor must be sent a separate pulse for each step.
The stepper motor can only take one step at a time and each step is the same size. Since each
pulse causes the motor to rotate a precise angle, typically 1.8°, the motor's position can be
controlled without any feedback mechanism
RPM = a/360 * fz * 60
RPM = Revolutions per minute.
“a” = step angle
“fz” = pulse frequency in hertz
78. Speed of rotation of stepper motor can be determined from..........?
A) B) C) D)
79. ............... is based on heating effect of current? (Check Hot Wire Instrument On
Net)
A)Hot wire Instrument B)Megger C)Watt meter D)Voltmeter
80. The motor in which Primary windings is stationary and secondary rotates, also
called transformer motor is .................. Motor?
A)Magnetically coupled B)DC Motor C) Asynchronous D)Induction
81. Types of generators are..................?
A)01 B)05 C)03 D)02
82. In synchronous motor current is provided by ................ ?
A)Rotor B)DC Current source C)AC I Source D)None
Series RLC Circuit at Resonance. Since the currentflowing through a series resonance
circuit is the product of voltage divided by impedance, at resonance the impedance, Z is
at its minimum value, ( =R ). Therefore, the circuit current at this frequency will be at its
maximum value of V/R as shown below
XL=XC
83. Circuit current is ........................ at resonance?
A) Minimum B)Maximum C)Zero D)Infinite
Parallel resonance is a resonance condition that usually occurs in parallel
resonant circuits, where the voltage becomes a maximum for a given current. Being
a parallel resonance means the impedance is high and inrush surge current relatively low
compared to a simple capacitor.
84. At parallel resonance the Impedance is ........................ ? (Check parallel
resonance On Web)
A)Min B)Max C)Zero D)Unity
85. If all the conductors in a power system are grounded to the same location, then
the risk of electric shock will be..................?
A)Max B)Min C)Zero D)Neglected
Battery charging requires constant voltage supply of course DC. And the current required
here is low as compared to load current. So we could use DC shunt generator for the use.
The above mentioned is for general purpose lead acid cells or Lithium Iron batteries or
Nickel Cadmium batteries
86. For charging batteries we have................Generators?
A)Shunt B)Series C)Compound D)None
87. Transmission lines mostly use High Voltage.....................Phase AC?
A)Single B)Two C)Three D)Neutral
88. In submarine power systems, power is transmitted through ................... cables?
A)HV DC B)LV DC C)Under Ground D)Over Head
Electric Forces and Fields. test charge with a force, F. The closer the test chargeis to
the body, the greater the force. The direction of the net electric field is defined to be in
the direction of the force acting on a positive test charge.
E=F/Q
89. The electric force on a test charge in an electric field is proportional
to...................?

You might also like