Professional Documents
Culture Documents
Blaine Fineness ASTM C 204
Blaine Fineness ASTM C 204
for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Copyright by ASTM Int'l (all rights reserved); Tue Aug 22 21:39:05 EDT 2017
2
Downloaded/printed by
Pontificia Universidad Javeriana de Colombia - PUJ (Pontificia Universidad Javeriana de Colombia - PUJ) pursuant to License Agreement. No further reproductions authorized.
C188 − 16
mixtures, density may be more usefully expressed as specific gravity, the 8.2 The multilaboratory standard deviation for portland
latter being a dimensionless number. Calculate the specific gravity (sp gr) cements has been found to be 0.037.4 Therefore, the results of
as follows:
two properly conducted tests from two different laboratories on
sp gr = cement density/water density at 4°C samples of the same cement should not differ by more than
(where the density of water at 4°C 1 g ⁄cm3). 0.10.4
8. Precision and Bias 8.3 Since there is no accepted reference material suitable for
8.1 The single-operator standard deviation for portland determining any bias that might be associated with this test
cements has been found to be 0.012.4 Therefore, the results of method, no statement on bias is being made.
two properly conducted tests by the same operator on the same
material should not differ by more than 0.03. 9. Keywords
4
These numbers represent the 1s and d2s limits described in Practice C670.
9.1 density; hydraulic cement; specific gravity
SUMMARY OF CHANGES
Committee C01 has identified the location of selected changes to this standard since the last issue (C188 – 15)
that may impact the use of this standard. (Approved Dec. 15, 2016.)
Committee C01 has identified the location of selected changes to this standard since the last issue (C188 – 14)
that may impact the use of this standard. (Approved Oct. 1, 2015.)
(1) Revised 6.2, 6.3, and 7.2. (2) Added Notes 4 and 5, and 7.2.1 and 7.2.2.
Committee C01 has identified the location of selected changes to this standard since the last issue (C188–09)
that may impact the use of this standard. (Approved July 1, 2014.)
(1) Added 1.5, Sections 3 and 4. (2) Revised 5.3, 7.2, and Note 6.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/
Copyright by ASTM Int'l (all rights reserved); Tue Aug 22 21:39:05 EDT 2017
3
Downloaded/printed by
Pontificia Universidad Javeriana de Colombia - PUJ (Pontificia Universidad Javeriana de Colombia - PUJ) pursuant to License Agreement. No further reproductions authorized.