2h Apt Inspection Technologies
aT
Tide Document No. Rev. | Page
ATTRTIOO 18 1
RADIOGRAPHIC EXAMINATION WELDS
Volume No. Product/Structure
Doe Type Derived From Rev.
Tob No. Project Giieat
GENERAL
SPECIFICATION
A Rev] KIND OF REVISION
‘This specification complies with ASME Code Sec. 1, V, IX, VIII div. 1, 2007 Edition 2009
Addenda,
. ‘This specification compiles wi
ASME B31.1, 2007 Edition 2009 Addenda.
18 | Updated ASME Code 2007 Edition with Addenda up to Addendum 2009 included.
Updated ASME B31.1, 2007 Edition with Addenda up to Addendum 2009 included.
(Modified para. 16.1 item ¢).
17 _| Updated in accordance with ASME B31.1, 2007 Edition. Modified Para. 3.3.
16 | Updated ASME 2007 Edition
15 | Updated ASME 2004 Edition with Addenda up to Addendum 2006 included.
14 | Updated ASME 2004 Edition
13 | Updated ASME 2001 Edition and 2003 Addenda.
Engineer | Engineer | Quality NDT Lev til
Fazal Kiran | Balakrishna 25/0012
Prepared | Checked | Checked | Checked | Checked | Approved Dateys Apt Inspection Technologies
air
‘Confidential intmaso,propenty of Ap Inspection Technolgies Noto be used for any purpose eer ha tht for which itis supplied
Project Doc no. Rev.
STANDARD AIT/RT/00 18 2
INDEX
1. SCOPE
2. GENERALITY
3. APPLICABILITY AND TIME OF EXAMINATION
4, SURFACE PREPARATION
5,
6
RADIOGRAPHIC TECHNIQUE,
. RADIOGRAPHIC DENSITY LIMITATION
7. CALIBRATION
& SCATTERED RADIATION
9, GEOMETRICAL UNSHARPNESS
10. EQUIPMENT
11, FILM SELECTION AND SCREENS
12, IMAGE QUALITY INDICATORS (IQ)
13, SYSTEM OF IDENTIFICATION AND MARKERS
14, FILM PROCESSING
15, INTERPRETATION OF RADIOGRAPHS
16. ACCEPTANCE STANDARDS
17, PERSONAL QUALIFICATION
18 REPORT
FIG. 1-2ae Apt Inspection Technologies
AT
Project Doe no.
STANDARD. AIT/RT/00 18 3
1. SCOPE
‘This specification covers al permitted technique procedures 10 perform a radiographic
examination of welds to be used in power boiler steam generator construction.
2. GENERALITY
2.1 The examination performed according to this specification is in accordance with ASME
Code Sect. V Article 2, with ASME Code Sect. {, with ASME Code Sect. VIM Div. 1,
with ASME section IX and with ASME B31.1
2.2. This specification shall be applied to examination of welds during the fabrication
process whenever required by the applicable Quality Control Plan (CQ) and/or
specification.
2.3. For particular production job, radiographic examination shall be performed according to
the applicable “Instruction Sheet” referencing the present specification and giving at
least the following technique variables:
= material and thickness range
= isotope used or maximum Xray voltage
- minimum source-to-object distance
~ maximum distance from source side of objects to the film
= maximum source size
= film brand and designation
= screens used
2.3.1 Demonstration of the density and IQI image requirements of the Instruction Sheet on
production or technique radiographs shall be considered a satisfactory compliance of
Instruction Sheet.
3, APPLICABILITY AND TIME EXAMINATION
3.1 This procedure applies to carbon, low or high alloy steet welded materials.
3.2. This procedure may be used for pressure and non pressure parts of power boiler steam
generator
3.3 Time of examination
‘The radiographic examination shall be performed before or after postweld heat
treatment, Radiographic examination of welds according to ASME B31.1 for P-No. 3, 4,
5a and Sb shall be performed after PWHT.
ns