Professional Documents
Culture Documents
Fittings
Buttwelding Specifications ASTM A234/A234M
Fittings (Moderate and High Temperature Service)
Dimensions ASME B36.9 & ASME B16.28
Product Elbows, Return Bends, Tees,
Crosses, Reducers, End Caps
Grade WPB
High Pressure Fittings Specification ASTM A105
Dimensions ASME B16.11
Product Elbows, Tees, Couplings, Unions, Hex Nipples,
Hex Plugs, Brushes & other reducing fittings,
Thread Outlets, Socket Outlets, Weld Outlets, Pipe Nipples
Grade Forged Steel
Flanges
Flanges Specifications ASTM A105/A105M
Dimensions ASME B16.5
Product Weld Neck, Slip-on, Blind, Socket Weld, Threaded
Face Raised Face, Flat Face
Bore Pipe Schedule
Class 150, 300, 400, 600, 900, 1500, 2500 (to 600mm only)
Grade Carbon Steel
Specifications AS2129
Dimensions AS2192 & BS 4504
Applications Slip-on, Blind “Table” Flanges
Face Flat Face
Bore To suit Pipe & Tube OD
Table D, E, F and H and DIN 16
Grooved
Grooved Specifications ULFM
Product Couplings: Lightweight & Rigid, Tees, Elbows, Caps,
Mechanical Tees, Concentric Reducers, Reducing Couplings
Grooved Butterfly, Gate & Checked Couplings,
Finish Painted & Galvanised
While every care has been taken to ensure the accuracy of this information,
Pipe & Engineering does not accept any responsibility for errors loss or damage as a result of this literature.
Formula to attain approximate mass in kilograms per metre (kg/m) for Steel Round Pipe and Tubing
THE ASME CODE FOR PRESSURE PIPING including allowable stress values (SE) for metal temperatures up to 595°C for Carbon Steel Pipe, but cautions that conversion of carbides
to graphite (graphitization) may occur in Carbon Steel Pipes after prolonged exposures to temperatures over 425°C. For this reason, with temperatures above 425°C it is recommended
that Alloy Steel Pipes should be used.
Allowable Stress values (SE) used in tabulated calculations are those approved for piping systems which come under Section B313.3 of the Code.
For practical purposes, the ,etal temperature in a pipe can be considered to be equal to the temperature of the line fluid.
The Pressure/Temperature Chart lists maximum allowable pressure ratings for Seamless 3. ASTM A333 Seamless Carbon Steel Pipes for Low Temperatures service:
Carbon Steel Pipe Grade B, with plain ends at temperatures up to 450°C. The pressures Grade 6 Use 1.0 for all temperatures drwn to -46°C
shown can be used as the basis for calculating maximum allowable pressure ratings for 4. ASTaM A333 Seamless Alloy Steel Pipes for Low Temperature service:
other pipes by applying the following factors: Grade 3. - Use 1.08 for -101 to +38°C and 0.93 for 38 to 350°C
1. Seamless Grade A Pipes: Use 0.80 to 250°C, 0.85 from 260 to 370°C, 0.82 at 400°C, Grade 4. - Use 1.00 for -101 to +38°C and 0.86 for 38 to 350°C
086 at 425°C and .090 at 450°C Grade 7. - Use 1.08 for -73 to +38°C and 0.93 for 38 to 350°C
2. Electric Resistance Welded Pipes: For other grades and temperatures above 350°C refer Appendix A of ANSI B31.3
Grade A. - Use 0.68 to 205°C, 0.72 from 260 to 370°C, 0.70 at 400°C, 0.73 at 425°C ** Caution - Codes for the specific application may vary
and .077 at 450°C * For Temperatures above 425°C See Above Notes on Graphitization
Grade B. - Use 0.85 at all temperatures.
B
A
H
A
B
A A T
T T T1 T1
D
D D D D
Long and Short Radius Elbows ASME B16.9 & B16.28 (in mm) Concentric and Eccentric Reducers ASME B16.9 (in mm)
Centre to End Norminal Outside Diameter End Nominal Outside Diameter End
Nominal Outside Shirt Radius Pipe at Bevel to Pipe at Bevel to
Long Radius Elbow
Pipe Diameter Elbow Size Large Small End Size Large Small End
Size at Bevel 90 Deg 45 Deg 90 Deg mm End End H mm End End H
mm D A B A 20x15 26.7 21.3 38.1 150x125 168.1 141.2 139.7
15 21.3 38.1 15.7 - 25x20 33.5 26.7 50.8 150x100 114.3
20 26.7 28.4 11.2 - 25x15 21.3 150x80 88.9
25 33.5 38.1 22.4 25.4 32x25 42.2 33.5 50.8 150x65 73.2
32 42.2 47.8 25.4 31.8 32x20 26.7 200x150 218.9 168.1 152.4
40 48.3 57.2 28.4 38.1 32x15 21.3 200x125 141.2
40x32 48.3 42.2 63.5 200x100 114.3
50 60.5 76.2 35.1 50.8 40x25 33.5 200x80 88.9
65 73.2 95.2 44.4 63.5 40x20 26.7 250x200 273.0 218.9 177.8
80 88.9 114.3 50.8 76.2 40x15 21.3 250x150 168.1
100 114.3 152.4 63.5 101.6 50x40 60.5 48.3 76.2 250x125 141.2
125 141.2 190.5 79.2 127.0 50x32 42.2 250x100 114.3
150 168.1 228.6 95.2 152.4 50x25 33.5 300x250 323.8 273.0 203.2
200 218.9 304.8 127.0 203.2 50x20 26.7 300x200 218.9
250 273.0 381.0 158.8 254.0 65x50 73.2 60.5 88.9 300x150 168.1
65x40 48.3 300x125 141.2
300 323.8 457.2 190.5 304.8 65x32 42.2 350x300 355.6 323.8 330.2
350 355.6 533.4 222.2 355.6 65x25 33.5 350x250 273.0
400 406.4 609.6 254.0 406.4 80x65 88.9 73.2 88.9 350x200 218.9
450 457.2 685.8 285.8 457.2 80x50 60.5 350x150 168.1
500 508.0 762.0 317.5 508.0 80x40 48.3 400x350 406.4 355.6 355.6
600 609.6 914.4 381.0 609.6 80x32 42.2 400x300 323.8
100x80 114.3 88.9 101.6 400x250 273.0
NOTE: T,T1 & T2 = Wall Thickness Designated as per Linepipe schedule 100x65 73.2 400x200 218.9
(refer Page 1.) 100x50 60.5 450x400 457.2 406.4 381.0
100x40 48.3 450x350 355.6
125x100 141.2 114.3 127.0 450x300 323.8
125x80 88.9 450x250 273.0
125x65 73.2 500x450 508.0 457.2 508.0
125x50 60.5 500x400 406.4
500x350 355.6
500x300 323.8
600x500 609.6 508.0 508.0
600x450 457.2
600x400 406.4
K
T T
K
D D
P P
T
P
Long and Short Radius Return Elbows ASME B16.9 & B16.28 (in mm) Caps ASME B16.9 (in mm)
Nominal Outside Long Radius Short Radius Nominal Outside Limiting
Pipe Diameter Centre to Back to Centre to Back to Pipe Diameter Length* Wall Thickness
Size at Bevel Centre Face Centre Face Size at Bevel E for Length
mm D P K P K mm D E
15 21.3 76.2 47.8 - - 15 21.3 25.4 4.6
20 26.7 57.2 42.9 - - 20 26.7 25.4 3.8
25 33.5 76.2 55.6 50.8 41.1 25 33.5 38.1 4.6
32 42.2 95.2 69.8 63.5 52.3 32 42.2 38.1 4.8
40 48.3 114.3 82.6 76.2 62.0 40 48.3 38.1 5.1
50 60.5 152.4 106.4 101.6 81.0 50 60.5 38.1 5.6
65 73.2 190.5 131.8 127.0 100.1 65 73.2 38.1 7.1
80 88.9 228.6 158.8 152.4 120.7 80 88.9 50.8 7.6
100 114.3 304.8 209.6 203.2 158.8 100 114.3 63.5 8.6
125 141.2 381.0 261.9 254.0 196.9 125 141.2 76.2 9.7
150 168.1 457.2 312.7 304.8 236.5 150 168.1 88.9 10.9
200 218.9 609.6 414.3 406.4 312.7 200 218.9 101.6 12.7 *LENGTH E
APPLIES FOR
250 273.0 762.0 517.7 508.0 390.7 250 273.0 127.0 12.7
THICKNESS NOT
300 323.8 914.4 619.3 609.6 466.9 300 323.8 152.4 12.7
EXCEEDING
350 355.6 1066.8 711.2 711.2 533.4 350 355.6 165.1 12.7
THAT GIVEN
400 406.4 1219.2 812.8 812.8 609.6 400 406.4 177.8 12.7
IN COLUMN
450 457.2 1371.6 914.4 914.4 685.8 450 457.2 203.2 12.7 “LIMITING WALL
500 508.0 1524.0 1016.0 1016.0 762.0 500 508.0 228.6 12.7 THICKNESS FOR
600 609.6 1828.8 1219.2 1219.2 914.4 600 609.6 266.7 12.7 LENGTH E”
5 Buttweld Fittings ANSI B16.9 & B16.28 Buttweld Fittings ANSI B16.9 & B16.28 6
BUTTWELD FITTINGS ASME B16.9 & B16.26 6
D D D D
T T2 T T2
T1
T1
T
T
M
M
M
M
D
D
D
D
C C C C C C C C
Straight and Reducing Tees ASME B16.9 (in mm) Straight and Reducing Tees ASME B16.9 (in mm)
Nominal Outside Diameter Centre-to-end Nominal Outside Diameter Centre-to-end Nominal Outside Diameter Centre-to-end Nominal Outside Diameter Centre-to-end
Pipe at Bevel Pipe at Bevel (1) Pipe at Bevel Pipe at Bevel (1)
Size D Run Outlet Size D Run Outlet Size D Run Outlet Size D Run Outlet
mm Run Outlet C M mm Run Outlet C M mm Run Outlet C M mm Run Outlet C M
15x15 21.3 21.3 25.4 25.4 100x100 114.3 114.3 104.6 104.6 350x350 355.6 355.6 279.4 279.4 500x500 508.0 508.0 381.0 381.0
20x20 26.7 26.7 28.4 28.4 100x80 88.9 98.6 350x300 323.8 269.7 500x450 457.2 368.3
20x15 21.3 28.4 100x65 73.2 95.2 350x250 273.0 257.0 500x400 406.4 355.6
25x25 33.5 33.5 38.1 38.1 100x50 60.5 88.9 350x200 218.9 247.6 500x350 355.6 355.6
25x20 26.7 38.1 100x40 48.3 85.9 350x150 168.1 238.3 500x300 323.8 345.9
25x15 21.3 38.1 125x125 141.2 141.2 124.0 124.0 400x400 406.4 406.4 304.8 304.8 500x250 273.0 333.2
32x32 42.2 42.2 47.8 47.8 125x100 114.3 117.3 400x350 355.6 304.8 500x200 218.9 323.8
32x25 33.5 47.8 125x80 88.9 111.3 400x300 323.8 295.1 600x600 609.6 609.6 431.8 431.8
32x20 26.7 47.8 125x65 73.2 108.0 400x250 273.0 282.4 600x500 508.0 431.8
32x15 21.3 47.8 125x50 60.5 104.5 400x200 218.9 373.0 600x450 457.2 419.1
40x40 48.3 48.3 57.2 57.2 150x150 168.1 168.1 142.7 142.7 400x150 168.1 263.7 600x400 406.4 406.4
40x32 42.2 57.2 150x125 141.2 136.7 450x450 457.2 457.2 342.9 342.9 600x350 355.6 406.4
40x25 33.5 57.2 150xl00 114.3 130.0 450x400 406.4 330.2 600x300 323.8 396.7
40x20 26.7 57.2 150x80 88.9 124.0 450x350 355.6 330.2 600x250 273.0 384.0
40x15 21.3 57.2 150x65 73.2 120.5 450x300 323.8 320.5
50x50 60.5 60.5 63.5 63.5 200x200 218.9 218.9 177.8 177.8 450x250 273.0 307.8
50x40 48.3 60.5 200x150 168.1 168.1 450x200 218.9 298.4
50x32 42.2 57.2 200x125 141.2 162.1
50x25 33.5 50.8 200xl00 114.2 155.4 NOTE (1): OUTLET DIMENSION “M” FOR SIZES 350 & LARGER
50x20 26.7 44.4 250x250 273.0 273.0 215.9 215.9 IS RECOMMENDED BUT NOT MANDATORY
65x65 73.2 73.2 76.2 76.2 250x200 218.9 203.2
65x50 60.5 69.8 250x150 168.1 193.5 NOTE (2): 1, T1 & T2 = Wall Thickness Designated as per Linepipe schedule
65x40 48.3 66.5 250x125 141.2 190.5 (refer Page 1.)
65x32 42.2 63.5 250xl00 114.3 184.2
65x25 33.5 57.2 300x300 323.8 323.8 254.0 254.0
80x80 88.9 88.9 85.9 85.9 300x250 273.0 241.3
80x65 73.2 82.6 300x200 218.9 228.6
80x50 60.5 76.2 300x150 168.1 218.9
80x40 48.3 73.2 300x125 141.2 215.9
80x32 42.2 69.8
BLIND (BLD)
SOCKET WELD (SW) THREADED (THD)
NOMINAL SIZE
CLASS 150 (PN20) 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
OD A 90 100 110 120 130 150 180 190 230 255 280 345 405 485 535 600 635 700 815
MIN THICK* D 11.5 13.0 14.5 16.0 17.5 19.5 22.5 24.0 24.0 24.0 25.5 29.0 30.5 32.0 35.0 37.0 40.0 43.0 48.0
HUB LENGTH** C 16 16 17 21 22 25 29 30 33 36 40 44 49 56 57 64 68 73 83
HUB LENGTH W/N B 48 52 56 57 62 64 70 70 76 89 89 102 102 114 127 127 140 145 152
PCD K 60.5 70.0 79.5 89.0 98.5 120.5 139.5 152.5 190.5 216.0 241.5 298.5 362.0 432.0 476.0 540.0 578.0 635.0 749.5
BOLT HOLE DIA H 16 16 16 16 16 20 20 20 20 22 22 22 26 26 30 30 33 33 36
No BOLTS 4 4 4 4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20
WEIGHT Kg*** 0.5 0.7 1.0 1.1 1.4 2.2 3.8 4.1 5.9 6.1 8.2 12.7 17.2 27.2 35.4 42.2 52.6 65.3 91.6
WEIGHT Kg W/N 0.8 0.9 1.1 1.4 1.8 2.8 4.4 5.2 7.5 9.5 11.3 19.1 25.4 38.1 51.3 63.5 74.9 89.4 121.7
WEIGHT Kg BLIND 0.9 0.9 0.9 1.4 1.8 2.3 3.2 4.1 7.7 9.1 12.0 21.4 30.5 50.6 63.0 85.0 99.0 129.0 190.0
CLASS 300 (PN50) 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
OD A 95 120 125 135 155 165 190 210 255 280 320 380 445 520 585 650 710 775 915
MIN THICK* D 14.5 16.0 17.5 19.5 21.0 22.5 25.5 29.0 32.0 35.0 37.0 41.5 48.0 51.0 54.0 57.5 60.5 63.5 70.0
HUB LENGTH** C 22 25 27 27 30 33 38 43 48 51 52 62 67 73 76 83 89 95 106
HUB LENGTH W/N B 52 57 62 65 68 70 76 79 86 98 98 111 117 130 143 146 159 162 168
PCD K 66.5 82.5 89.0 98.5 114.5 127.0 149.0 168.5 200.0 235.0 270.0 330.0 387.5 451.0 514.5 571.5 628.5 686.0 813.0
BOLT HOLE DIA H 16 20 20 20 22 20 22 22 22 22 22 26 30 33 33 36 36 36 42
No BOLTS 4 4 4 4 4 8 8 8 8 8 12 12 16 16 20 20 24 24 24
WEIGHT Kg*** 0.7 1.3 1.4 2.0 2.8 3.1 4.5 6.1 9.5 12.7 16.3 25.4 35.4 50.8 72.2 95.3 114.9 139.4 222.3
WEIGHT Kg W/N 0.9 1.4 1.8 2.3 3.1 3.7 5.6 8.2 11.8 16.3 20.0 32.2 45.4 64.4 93.5 113.1 138.4 167.5 235.6
WEIGHT Kg BLIND 0.9 1.4 1.8 2.7 3.2 3.6 5.5 7.3 12.7 16.8 21.8 35.9 55.0 83.0 110.0 143.0 188.0 234.0 364.0
CLASS 600 (PN100) 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
OD A 95 120 125 135 155 165 190 210 275 330 355 420 510 560 605 685 745 815 940
MIN THICK* D 14.5 16.0 17.5 21.0 22.5 26.5 29.0 32.0 38.5 44.5 48.0 55.5 63.5 66.5 70.0 76.5 83.0 89.0 102.0
HUB LENGTH** C 22 25 27 29 32 37 41 46 54 60 67 76 86 92 94 106 117 127 140
HUB LENGTH W/N B 52 57 62 67 70 73 79 83 102 114 117 133 152 156 165 178 184 190 203
PCD K 66.5 82.5 89.0 98.5 114.5 127.0 149.0 168.5 216.0 267.0 292.0 349.0 432.0 489.0 527.0 603.0 654.0 724.0 838.0
BOLT HOLE DIA H 16 20 20 20 22 20 22 22 26 30 30 33 36 36 39 42 45 45 52
No BOLTS 4 4 4 4 4 8 8 8 8 8 12 12 16 20 20 20 20 24 24
WEIGHT Kg*** 0.9 1.4 1.6 2.0 3.0 3.6 5.5 6.8 15.0 28.6 36.3 44.0 80.4 97.6 117.6 166.2 216.1 277.9 397.7
WEIGHT Kg W/N 1.4 1.6 1.8 2.5 3.6 4.5 6.4 8.2 16.8 30.9 38.1 50.6 85.8 102.6 157.5 218.4 252.0 313.3 443.6
WEIGHT Kg BLIND 0.9 1.4 1.8 2.7 3.6 4.6 6.8 9.1 18.6 30.9 39.1 63.0 105.0 134.0 172.0 240.0 302.0 389.0 534.0
* MINIMUM THICKNESS INCLUDING RAISED FACE BUT EXCLUDING HUB OR WELD NECK
** HUB LENGTH FOR SLIP ON SCREWED & SOCKET WELD FLANGES
*** APPROXIMATE WEIGHT FOR SLIP ON SOCKET WELD & SCREWED
# OD OF PIPE MUST BE NOMINATED
7 Flange ASME B16.5 Forged Flanges Flange ASME B16.5 Forged Flanges 8
FLANGE ASME B16.5 FORGED FLANGES 8
NOMINAL SIZE
CLASS 900 (PN150) 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
OD A 240 295 350 380 470 545 610 640 705 785 855 1040
MIN THICK* D 38.5 44.5 51.0 56.0 63.5 70.0 79.5 86.0 89.0 102.0 108.0 140.0
HUB LENGTH** C USE CLASS 1500 DIMENSIONS 54 70 79 86 102 108 117 130 133 152 159 203
HUB LENGTH W/N B 102 114 127 140 162 184 200 213 216 229 248 292
PCD K 190.5 235.0 279.5 317.5 393.5 470.0 533.5 559.0 616.0 686.0 749.5 901.5
BOLT HOLE DIA H IN THESE SIZES 26 32 35 32 39 39 39 42 45 52 54 68
No BOLTS 8 8 8 12 12 16 20 20 20 20 20 20
WEIGHT Kg*** 14.1 24.1 37.7 49.0 78.1 111.2 148.0 172.5 208.4 293.7 359.6 671.9
WEIGHT Kg W/N 13.2 23.2 39.0 49.9 84.9 121.7 168.9 255.2 311.0 419.5 528.5 956.6
WEIGHT Kg BLIND 14.0 24.6 39.6 51.0 90.0 132.0 188.0 225.0 281.0 400.0 503.0 954.0
CLASS 1500 (PN250) 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
OD A 120 130 150 160 180 215 245 270 310 375 395 485 585 675 750 825 915 985 1170
MIN THICK* D 22.5 25.5 29.0 29.0 32.0 38.5 41.5 48.0 54.0 73.5 83.0 92.0 108.0 124.0 133.5 146.5 162.0 178.0 203.5
HUB LENGTH** C 32 35 41 41 44 57 64 73 90 105 119 143 159 181
HUB LENGTH W/N B 60 70 73 73 83 102 105 113 124 155 171 213 254 283 298 311 327 356 406
PCD K 82.5 89.0 101.5 111.0 124.0 165.0 190.5 203.0 241.5 292.0 317.5 393.5 482.5 571.5 635.0 705.0 774.5 832.0 990.5
BOLT HOLE DIA H 22 22 26 26 30 26 30 33 36 42 39 45 52 56 60 68 76 80 94
No BOLTS 4 4 4 4 4 8 8 8 8 8 12 12 12 16 16 16 16 16 16
WEIGHT Kg*** 2.7 2.7 3.4 4.5 6.4 10.0 16.3 21.8 33.3 59.9 74.5 117.1 197.9 302.8
WEIGHT Kg W/N 3.2 3.2 3.9 4.5 6.4 10.9 16.3 21.8 31.3 59.9 74.5 123.9 206.1 313.3
WEIGHT Kg BLIND 1.8 2.7 4.1 4.6 6.4 11.4 15.9 21.8 33.2 65.0 72.0 137.0 230.0 352.0
* MINIMUM THICKNESS INCLUDING RAISED FACE BUT EXCLUDING HUB OR WELD NECK
** HUB LENGTH FOR SLIP ON, SCREWED & SOCKET WELD FLANGES
*** APPROXIMATE WEIGHT FOR SLIP ON, SOCKET WELD & SCREWED
# OD OF PIPE MUST BE NOMINATED
FLANGES ABOVE DN 600 ARE NOT INCLUDED IN ASME B16.5 AND THE CLASS DESIGNATIONS IN THESE
LARGE DIAMETERS DO NOT IMPLY SPECIFIC TEMPERATURE/PRESSURE RATINGS.
90° ELBOW TEE CROSS 45° ELBOW COUPLING HALF COUPLING CAP
UNION
SOCKET WELD UNION SCREWED
6 6.83 / 6.43 3.17 3.17 1.24 41.40 21.80 10.92 3.17 22.40 9.60 14.70 2.41
8 9.85 / 9.45 3.17 3.17 1.24 41.40 21.80 14.22 3.30 22.40 9.60 19.00 3.02
10 13.92 / 3.51 3.43 3.43 1.37 46.00 25.90 17.78 3.48 26.90 9.60 22.90 3.20
15 17.47 / 17.07 3.68 3.68 1.50 49.00 31.20 21.84 4.06 26.90 9.60 27.70 3.73
20 21.79 / 21.39 4.06 4.06 1.68 56.90 31.10 27.18 4.27 31.80 12.70 33.50 3.91
25 28.14 / 27.74 4.57 4.44 1.85 62.00 45.50 34.04 4.95 34.30 12.70 41.40 4.55
32 35.76 / 35.36 5.33 5.21 2.13 71.10 54.90 42.67 5.28 40.60 12.70 50.50 4.85
40 41.61 / 41.20 5.84 5.59 2.31 76.50 61.50 48.77 5.54 42.20 12.70 57.20 5.08
50 52.53 / 52.12 6.60 6.35 2.69 86.10 75.20 61.47 6.05 45.50 15.80 70.10 5.54
65 64.72 / 64.31 7.49 7.11 3.07 102.40 91.70 74.17 7.65 61.70 15.80 85.30 7.01
80 77.67 / 77.27 8.25 8.00 3.53 109.00 109.20 90.17 8.31 63.80 15.80 102.40 7.62
9 Forged Steel High Pressure Fittings to ASME B16.11 Forged Steel High Pressure Fittings 300lb & 6000lb 10
FORGED STEEL HIGH PRESSURE FITTINGS TO B16.11 10
SOCKET WELD
MAX/MIN 3000 6000 3000 6000 3000 6000 3000 6000 3000 6000 3000 6000
6 11.2/10.8 7.6/6.1 4.8/3.2 3.18 3.43 2.41 3.15 9.5 11.00 11.00 8.00 8.00 6.5 16.0 4.8 6.4
8 14.6/14.2 10.0/8.5 7.1/5.6 3.30 4.01 3.02 2.68 9.5 11.00 13.50 8.00 8.00 6.5 16.0 4.8 6.4
10 18.0/17.6 13.3/11.8 9.9/8.4 3.50 4.37 3.20 4.01 9.5 13.50 15.50 8.00 11.00 6.5 17.5 4.8 6.4
15 22.2/21.8 16.6/15.0 12.5/11.0 4.09 5.18 3.73 4.78 9.5 15.50 19.00 11.00 12.50 9.5 22.5 6.4 7.9
20 27.6/27.2 21.7/20.2 16.3/14.8 4.27 6.04 3.91 5.56 12.5 19.00 22.50 13.00 14.00 9.5 24.0 6.4 7.9
25 34.3/33.9 27.4/25.9 21.5/19.9 4.98 6.93 4.55 6.35 12.5 22.50 27.00 14.00 17.00 12.5 28.5 9.6 11.2
32 43.1/42.7 35.8/34.3 30.2/28.7 5.28 6.93 4.85 6.35 12.5 27.00 32.00 17.50 20.50 12.5 30.0 9.6 11.2
40 49.2/48.8 41.6/40.1 34.7/33.2 5.54 7.80 5.08 7.14 12.5 23.00 38.00 20.50 25.50 12.5 32.0 11.2 12.7
50 61.7/61.2 53.3/51.7 43.6/42.1 6.04 9.50 5.54 8.74 16.0 38.00 41.00 25.50 28.50 19.0 41.0 12.7 15.7
65 74.4/73.9 64.2/61.2 7.67 7.01 16.0 41.00 28.50 19.0 43.0 15.7 19.0
80 90.3/89.8 79.4/76.4 8.30 7.62 16.0 57.00 32.00 19.0 44.5 19.0 22.4
100 115.7/115.2 103.8/100.7 9.35 8.56 19.0 66.50 41.00 19.0 48.0 22.4 28.4
WORKING PRESSURES
Possible Temperature Limitations
Nominal
TEMPERATURE °C
Pressure
Ratings 38 66 93 121 149 177 204 232 260 288 316 343 371 399 427 427* 428* 510* *538*
2000lb 13780 13573 13366 13194 13056 12918 12746 12470 11954 11299 10610 9852 8991 8130 6993 5718 4237 2928 1619
3000lb 20670 20359 20084 19808 19602 19360 19119 18706 17948 16949 15915 14813 13504 12229 10507 8612 6373 4409 2445
6000lb 41340 40754 40168 39617 39232 38756 38239 37412 37142 33933 31831 29627 27008 24459 21014 17225 12780 8853 4926
+ These pressures are in accordance with ANSI Code for Pressure Piping (ASME 831.1)
* Suggest Alloy Steel above 482°C.
NOMINAAL SIZE
TABLE D 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
THICKNESS* D 5 5 5 6 6 8 8 10 10 13 13 13 16 19 22 22 25 29 32
OD A 95 100 115 120 135 150 165 185 215 255 280 335 405 455 525 580 640 705 825
PCD K 67 73 83 87 98 114 127 146 178 210 235 292 356 406 470 521 584 641 756
No BOLTS 4 4 4 4 4 4 4 4 4 8 8 8 8 12 12 12 12 16 16
BOLT SIZE H M12 M12 M12 M12 M12 M16 M16 M16 M16 M16 M16 M16 M20 M20 M24 M24 M24 M24 M27
BOLT LENGTH*** 45 45 45 50 50 60 60 60 65 65 65 70 75 85 100 95 100 110 120
WEIGHT SOW Kg 0.3 0.3 0.4 0.5 0.6 0.9 1.1 1.6 2.1 3.7 4.1 5.1 8.8 11.9 20.2 23.1 30.7 42.4 60.2
BLD Kg 0.28 0.31 0.41 0.54 0.68 1.12 1.36 2.14 2.89 5.28 6.36 9.11 16.39 24.56 37.86 46.21 63.94 90.00 136.00
TABLE E 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
THICKNESS* D 6 6 7 8 9 10 10 11 13 14 17 19 22 25 29 32 35 38 48
OD A 95 100 115 120 135 150 165 185 215 255 280 335 405 455 525 580 640 705 825
PCD K 67 73 83 87 98 114 127 146 178 210 235 292 356 406 470 521 584 641 756
No BOLTS 4 4 4 4 4 4 4 4 8 8 8 8 12 12 12 12 15 16 16
BOLT SIZE H M12 M12 M12 M12 M12 M16 M16 M16 M16 M16 M20 M20 M20 M24 M24 M24 M24 M24 M30
BOLT LENGTH*** 45 45 45 50 50 60 60 60 65 65 70 75 75 90 100 95 100 110 140
WEIGHT SOW Kg 0.3 0.4 0.5 0.6 0.9 1.2 1.3 1.8 2.7 3.9 5.3 7.5 12.1 15.6 26.6 33.6 42.9 55.5 90.3
BLD Kg 0.34 0.37 0.58 0.72 1.02 1.40 1.70 2.35 3.75 5.58 8.32 13.31 22.53 32.32 49.91 67.22 89.50 117.93 204.00
TABLE H 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
THICKNESS* D 13 13 14 17 17 19 19 22 25 29 29 32 35 41 48 54 60 67 76
OD A 115 115 120 135 140 165 185 205 230 280 305 370 430 490 550 610 675 735 850
PCD K 83 83 87 98 105 127 146 165 191 235 260 342 381 438 495 552 610 673 781
No BOLTS 4 4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20 24 24
BOLT SIZE H M16 M16 M16 M16 M16 M16 M16 M16 M16 M20 M20 M20 M24 M24 M27 M27 M30 M30 M33
BOLT LENGTH*** 60 60 60 65 65 75 75 75 85 100 100 100 120 120 130 140 160 150 180
WEIGHT SOW Kg 1.0 1.0 1.2 1.7 1.8 2.8 3.4 4.7 6.2 10.6 11.8 17.6 23.7 34.1 52.1 68.7 90.8 115.9 162.9
BLD Kg 1.01 1.07 1.26 1.93 2.08 3.23 4.06 5.77 8.26 14.31 16.84 27.35 40.41 61.47 90.66 125.47 170.7 226.00 343.00
PN16 15 20 25 32 40 50 65 80 100 125 150# 200# 250 300 350 400 450 500 600
THICKNESS* D 14 16 16 16 16 18 18 20 20 22 22 24 28 28 30 32 36 36 44
OD A 95 105 115 140 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840
PCD K 65 75 85 100 110 125 145 160 180 210 240 295 355 410 470 525 585 650 770
No BOLTS 4 4 4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20 20
BOLT SIZE H M12 M12 M12 M16 M16 M16 M16 M16 M16 M16 M20 M20 M20 M24 M24 M27 M27 M30 M33
BOLT LENGTH*** 50 55 55 60 60 65 65 70 75 80 90 90 100 100 120 120 120 130 140
WEIGHT SOW Kg 0.7 1.0 1.2 1.7 1.9 2.4 3.2 4.1 4.4 5.0 7.3 9.3 10.1 14.5 24.5 28.8 31.0 42.8 53.5
BLD Kg 0.8 1.1 1.3 2.0 2.3 3.1 3.9 4.6 5.6 8.1 11.2 17.3
* THICKNESS OF PLATE FLANGE NOTE IT IS NOT PRACTICAL TO PROVIDE PLATE FLANGES LESS THAN 12mmTHICK
# 0D OF PIPE MUST BE NOMINATED
*** LENGTHS OF BOLTS FOR PLATE STEEL FLANGES
NOTE PLATE FLANGES MUST NOT BE USED ON PRESSURE VESSELS -CERTIFIED BOILER PLATE FLANGES MUST BE USED
ELBOW ‘F. & F.’ ELBOW ‘M. & F.’ TEE ‘F’ TEE ‘F’ REDUCING
1 1 3 1 3 1 1 1
Elbows, ‘F. & F.’ —
8
—
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 4
1 3 1 3 1 1 1
Elbows, ‘M. & F.’ — —
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 —
1 1 3 1 3 1 1 1
Tees. ‘F.’ —
8
—
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 4
3 1 1 1 1 3 3 3 3 1 1 3 1 1 3 1 1 1 1
—X—
8 4
—X—
2 4
—X—
2 8
—X—
4 8
—X—
4 2
1 X—
2
1 X—
4
1—
4
X 1 1— X — 1— X 1 1— X 1— 2 X —
2 4 2 2 4 2
Tees. ‘F.’
Reducing 3 1 1 1 1 1 1
2 X—
4
2x1 2 X 1—
4
2 X 1—
2
2—
2
X 1— 2— X 2
2 2
3x2 3 X 2—
2
4x2 4x3 — —
Adaptor 1 3 1 3
B.S.P to B.S.P. or — — — — — 1 — — — — — — — —
N.P.T. to B.S.P. 4 8 2 4
1 1 3 1 1 1 1 3 3 1 3 3 3 1 1 3 1 3 1 3 1 1 3
—X—
4 8
—X—
8 4
—X—
2 4
—X—
2 8
—X—
4 4
—X—
4 8
—X—
4 2
1 X—
4
1 X—
8
1 X—
2
1 X—
4
1—
4
X — 1— X 1 1— X —
4 4 2 4
Sockets
Reducing 1 1 1 3 1 1 1 1 1 1 1
1—
2
X 1 1— X 1— 2 X —
2 4 4
2x1 2 X 1—
4
2 X 1—
2
2—
2
X 1— 2— X 2
2 2
3x1 3x2 3 X 2—
2
4x2 4 X 2—
2
4x3
1 1 3 1 3 1 1 1
Sockets —
8
—
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 — — —
1 3 1 3 1 1 1
Caps — —
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 4 — —
UNION ‘M. & F.’ UNION ‘F. & F.’ NIPPLE HEX. REDUCING NIPPLE HEX.
1 3 1 3 1 1 1
— —
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 4
Unions, ‘M. & F.’
All available in Steel to Steel or Steel to Bronze or Bronze to Bronze Seats
1 1 3 1 3 1 1 1
—
8
—
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 4
Unions, ‘F. & F.’
All available in Steel to Steel or Steel to Bronze or Bronze to Bronze Seats
1 1 3 1 3 1 1 1 1 3 3 3 3 1 1 3 1 3 1 1 3
— X—
4 8
— X— — X—
8 8 8 4
—
2
X —
4
—
2
—
8
X —
4
X—
8
— X—
4 2
1 X —
2
1 X —
4
1—
4
X — 1— X 1 1— X 1—
4 4 2 4
Nipples, Hex. Reducing 1 X 1 1 3 1 1 1 1 1 1
1—2
1 1—
2
X 1— 2 X —
4 4
2x1 2 X 1—
4
2X 1—
2
2—2
X 1—
2
2—
2
X 2 3x2 3 X 2—
2
4x2 4x3
1 1 3 1 3 1 1 1
Nipples, Hex. —
8
—
4
—
8
—
2
—
4
1 1—4
1—
2
2 2—
2
3 4
1 1 3 1 3 1 1 1 1 3 3 1 3 3 3 1 1 3 1 3 1 1 1 3 1
— X— — X— — X— — X— — X— — X— — X— — X—
4 8 8 8 8 4 2 4 2 8 4 4 4 8 4 2
1 X—
4
1 X—
8
1 X—
2
1 X—
4
1— X — 1— X — 1— X 1
4 2 4 4 4
—
Bushes, Hex.
1 1 1 3 1 1 1 1 3 1 1 1 1 1 1 1
1— X — 1— X — 1—X 1 1—X 1— 2 X — 2 X — 2 x 1 2 X 1— 2 X 1— 2—X1— 2—X 2 3 x 2 3 X 2— 4 x 2 4 X 2— 4 x 3
2 2 2 4 2 2 4 2 4 4 2 2 2 2 2 2
1 1 3 1 3 1 1 1
Plugs, Hex. —
8
—
4
—
8
—
2
—
4
1 1—
4
1—
2
2 2—
2
3 4 — — — —
1 1 3 1 3
Plugs, Square. —
8
—
4
—
8
—
2
—
4
— — — — — — — — — — —
1 1 3 1 3 1 1
Back Nuts —
8
—
4
—
8
—
2
—
4
1 1—
4
1—
2
2 — — — — — — —
TEMPERATURE
The SI unit of TEMPERATURE is the KELVIN -Symbol K
For most practical purposes of temperature measurement and most calculations involving temperatures, degrees Celsius, symbol DC will be used.
DEGREES FAHRENHEIT TO CELSIUS DEGREES CELSIUS TO FAHRENHEIT
(ºF _ 32) X 5/9 = °C (OC x 9/5) + 32 = of