Professional Documents
Culture Documents
XCAP LTE Analyzer LTE Parameter Accuver PDF
XCAP LTE Analyzer LTE Parameter Accuver PDF
Web: http://www.accuver.com
Email: sales@accuver.com
Introduction
Introduction of Appendix
This Analyzer Parameter Description manual specifies asynchronous parameters in
Parameter Trees in Analyzer graph/map/table/CDF/PDF.
History
Samsung ............................................................................................... 26
Common Basic Info .......................................................................... 26
Common Data Info ........................................................................... 26
LTE N Cell Information....................................................................... 27
LPHY Cell Search Info ....................................................................... 28
LPHY System Info ............................................................................ 29
LPHY Channel Quality Info ................................................................. 30
LPHY Parameter Info ........................................................................ 30
LPHY PHICH Info ............................................................................ 31
LL1 RF & Sync Info .......................................................................... 31
LL1 Downlink Info ............................................................................ 32
LL1 Uplink Info ................................................................................ 32
LL1 Measurement Config Info .............................................................. 32
LL2 SCH Configuration Info ................................................................. 33
Timer & Preamble Info ....................................................................... 33
Power Ramping & RA Supervision Info.................................................... 33
Max HARQ Msg3Tx & RACH Info ......................................................... 34
LL2 RNTI Info ................................................................................. 34
LL2 RLC Info .................................................................................. 34
LL2 PDCP Info ................................................................................ 35
LRRC Serving Cell Info ...................................................................... 36
LRRC State Variables Info .................................................................. 36
LRRC Timer info .............................................................................. 37
LNAS State Variables Info ................................................................... 37
LNAS MM(SIM/PLMN/Security) Info ....................................................... 38
Qualcomm ............................................................................................. 40
Configuration Info ............................................................................ 40
Power Info ..................................................................................... 50
Cell Search .................................................................................... 50
Ant Correlation Result ....................................................................... 51
Intrafreq Measurement Info ................................................................. 51
Channel Quality Info ......................................................................... 53
ML1 Downlink Info ........................................................................... 54
ML1 Uplink Info ............................................................................... 55
Random Access Procedure ................................................................. 55
Radio Link Monitoring Info .................................................................. 59
NAS ESM Bearer Context Info ............................................................. 59
NAS EMM State .............................................................................. 60
RRC Serving Cell Info ....................................................................... 61
RRC PLMN Search Info ..................................................................... 62
ML1 Serving Cell Info(Acquisition) ......................................................... 63
Physical Throughput ......................................................................... 63
MAC Throughput ............................................................................. 64
RLC Throughput .............................................................................. 64
PDCP Throughput ............................................................................ 64
GCT .................................................................................................... 66
L1 Status Info ................................................................................. 66
Serving Cell Signal Quality Info ............................................................ 67
Tx Power Info ................................................................................. 67
RACH Info ..................................................................................... 67
Timing Adjustment Info ...................................................................... 67
Cell Info ........................................................................................ 68
Search Result ................................................................................. 71
Channel Info .................................................................................. 71
CQI Info........................................................................................ 72
Multi-paths Profile ............................................................................ 73
PBCH BLER .................................................................................. 73
PDSCH BLER ................................................................................ 73
LGE
L1 Status Info
L1 status information shows physical layer status such as channel setup status, serving cell information,
PCH DRX and measurement periodicity, etc.
Parameter Description
The serving cell quality information shows SNR of reference signal (RS SNR) and received power of
reference signal (RS RSSI).
Parameter Description
Tx Power Info
Time sync report log shows the time sync status of UE.
Parameter Description
RACH Info
Parameter Description
Parameter Description
Cell Info
Cell Information display cell lists which are collected from Mp Searcher and Cell Searcher.
Parameter Description
INTRA>SYNC> RSRP Reference Signal Received Power of Intra cell which is known the sync position.
INTRA>SYNC> RSRQ Reference Signal Received Quality of Intra cell which is known the sync position
INTRA>SYNC> RSSI Received Power of Intra cell which is known the sync position
INTRA>SYNC>
Cell frame boundary in Intra Sync
FrameBound
INTRA>SYNC> CP length in Intra Sync
CPLength 0: Unknown
1 : Normal CP
2 : Extended CP
INTRA>SYNC> DL
Earfcn number in Intra Sync
Earfcn
INTRA>SYNC> Top Set PCI PCI with RSRP strength from top 1 to 20 from Intra Sync Cell
RSRP Top 1 to 20 RSRP from Intra Sync Cell
RSRQ Top 1 to 20 RSRQ from Intra Sync Cell
RSSI Top 1 to 20 RSSI from Intra Sync Cell
FrameBound Top 1 to 20 FrameBound from Intra Sync Cell
CPLength Top 1 to 20 CPLength from Intra Sync Cell
DL Earfcn Top 1 to 20 DL Earfcn from Intra Sync Cell
INTRA>ASYNC> RSRP Reference Signal Received Power of Intra cell which is unknown the sync position.
INTRA> ASYNC>
Reference Signal Received Quality of Intra cell which is unknown the sync position
RSRQ
INTRA> ASYNC> RSSI Received Power of Intra cell which is unknown the sync position
INTRA> ASYNC>
Cell frame boundary in Intra Async
FrameBound
Search Result
Search Result log shows Mp Search result and Cell Search result.
Parameter Description
Cell Searcher> PCI# Cell Search Energy, PCIG, Half Frame Idx and CP Length per PCI
(PCIG: 0 ~ 167, PCI: 0 ~ 503)
Earfcn EARFCN number
Used Cell Searcher
Num of Used Cell Searcher
Num
Channel Info
Parameter Description
Tx Correlation> Freq
Tx Correlation in Total Band(Sub Band 1 ~ 30)
Total Band(Avg)
Tx Correlation> Freq
Tx Correlation per Sub Band
Sub Band x
Rx Correlation> Freq
Rx Correlation in Total Band(Sub Band 1 ~ 30)
Total Band(Avg)
Rx Correlation> Freq
Tx Correlation per Sub Band
Sub Band x
H00 (Real)> Freq Sub
H00 (Real value) per Sub Band
Band x
H00 (Imaginary)> Freq
H00 (Imaginary value) per Sub Band
Sub Band x
H01 (Real)> Freq Sub
H00 (Real value) per Sub Band
Band x
H01 (Imaginary)> Freq
H00 (Imaginary value) per Sub Band
Sub Band x
H10 (Real)> Freq Sub
H00 (Real value) per Sub Band
Band x
H10 (Imaginary)> Freq
H00 (Imaginary value) per Sub Band
Sub Band x
H11 (Real)> Freq Sub
H00 (Real value) per Sub Band
Band x
H11 (Imaginary)> Freq
H00 (Imaginary value) per Sub Band
Sub Band x
CQI Info
The wideband CQI information shows measured CQI of wideband in the UE.
The sub-band CQI information shows the CQI (channel quality information) of sub-bands. The sub-band is
defined a unit for a group of resource elements used for reporting sub-band CQI.
Parameter Description
Multi-paths Profile
This information shows the channel impulse response of reference signals in the time domain.
Parameter Description
PBCH BLER
PBCH BLER displays how much transport blocks get CRC_NOK about total received transport blocks.
Parameter Description
PDSCH BLER
PDSCH BLER displays how much transport blocks get CRC_NOK about total received transport blocks.
Parameter Description
UE can’t calculate PDCCH BLER because UE doesn’t know when eNode-B sends its PDCCH. In other
words, UE detects PDCCH blindly. So, UE DM supports this item similar with PDCCH BLER.
Parameter Description
DL Grant & UL ACK/NACK Status(Improved) displays DL grant regardless any DCI format in every TTI.
According to TS36.212, each DCI format has the specific fields, not all, and the unnecessary fields are
displayed to the blank. Additionally, UL_ACK/NACK, CFI, and DCI_3/3A payload will be included in this
item.
Parameter Description
UL ACK/NACK> CW0>
ACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW0
ACK Rate
UL ACK/NACK> CW0>
NACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW0
NACK Rate
UL ACK/NACK> CW0>
DTX Count/(ACK Count+NACK Count+DTX Count)*100 in CW0
DTX Rate
UL ACK/NACK> CW1>
CW1 UL ACK result
ACK Count
UL ACK/NACK> CW1>
CW1 UL NACK result
NACK Count
UL ACK/NACK> CW1>
CW1 UL DTX result
DTX Count
UL ACK/NACK> CW1>
ACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW1
ACK Rate
UL ACK/NACK> CW1>
NACK Count/(ACK Count+NACK Count+DTX Count)*100 in CW1
NACK Rate
UL ACK/NACK> CW1>
DTX Count/(ACK Count+NACK Count+DTX Count)*100 in CW1
DTX Rate
DCI 3(Mode)> DCI 3/3A
CW0 DCI3/3A value
Value(CW0)
DCI 3(Mode)> DCI 3/3A
CW1 DCI3/3A value
Value(CW1)
DL Grant & UL Ack/Nack Status Info(Improved)[Detail per TTI] displays the related information per TTI.
Parameter Description
UL Grant Info Status log shows get UL Scheduling Grant information to PDCCH.
Parameter Description
UL Grant & DL Ack/Nack Status info[Detail per TTI] displays the related information per TTI.
Parameter Description
PDSCH PHY Throughput has displays how much to get the downlink data in 1sec.
Parameter Description
This information shows the log of transmit physical resource mapping information.
Parameter Description
Parameter Description
L2 DL Throughput
Parameter Description
L2 UL Throughput
Parameter Description
This item is for MAC BLER of downlink (PDSCH). Ratio of transport blocks which remain un-
acknowledged (CRC failure) after HARQ retransmission divided by total number of initial transmissions
received by UE MAC
Parameter Description
Parameter Description
Tx States> RB ID (x)>
Tx States RLC Mode (AM /UM/TM)
Mode
Tx States> RB ID (x)>
Tx States RLC Tx Entity state (NULL/DTR)
State
Rx States> RB ID (x)>
Rx States RLC Mode (AM /UM/TM)
Mode
Rx States> RB ID (x)>
Rx States RLC Tx Entity state (NULL/DTR)
State
XCAP-LTE Analyzer Parameter Description/Ed.04
Parameter Description
Parameter Description
Parameter Description
Parameter Description
RACH Response
RACH response receiving time
Receiving Time
Result 0: NACK, 1: ACK
RACH Preamble Identity RACH Preamble Identity
BackOff Indicator BackOff Indicator
Time Advance Time Advance
Temporary C-RNTI Temporary C-RNTI
MCS Modulation and coding Scheme
XCAP-LTE Analyzer Parameter Description/Ed.04
RNTI Info
Parameter Description
C-RNTI C-RNTI
RA-RNTI RA-RNTI
Temporary C-RNTI Temporary C-RNTI
Parameter Description
Parameter Description
Parameter Description
This item provides the state information of EMM (EPS Mobility Management), ECM (EPS Connection
Management) and PLMN and EU (EPS Update) status when each state is changed.
Parameter Description
This item provides the NAS state information of EMM (EPS Mobility Management), ECM (EPS Connection
Management) and PLMN and EMM Cache status when each state is changed.
Parameter Description
Parameter Description
Parameter Description
This item provides the information on both source cell and target cell when RRC perform cell reselection.
Parameter Description
Handover History
Parameter Description
Parameter Description
This item includes ESM instance information R3. Maximum number of ESM instance is 15(1~15). The
EPS Id uniquely identifies each ESM instance.
Parameter Description
st nd th
Tab Index 1: 1 tab, 2: 2 tab, … 15: 15 tab
EPS Id EPS ID
Linked Bearer Id Linked Bearer ID
XCAP-LTE Analyzer Parameter Description/Ed.04
Parameter Description
Parameter Description
Parameter Description
EUTRAN>PLMN PLMN
EUTRAN>Serving Cell
Serving Cell ID(PCI 0 ~ 503)
Info> Cell ID
EUTRAN>Serving Cell Serving Cell RSSI
Info>RSSI
EUTRAN>Serving Cell Serving Cell CINR
Info>CINR
EUTRAN>Serving Cell Serving Cell RSRP
Info>RSRP
EUTRAN>Serving Cell Serving Cell RSRQ
Info>RSRQ
EUTRAN>Serving Cell Serving Cell RSSI/CINR/RSRP/RSRQ per PCI
Info>All Cell Info
EUTRAN>Neighbor Cell
Neighbor Cell number
Info>NCell Num
EUTRAN>Neighbor Cell
Neighbor Cell EARFCN per Cell ID(PCI)
Info>EARFCN
EUTRAN>Neighbor Cell
Neighbor Cell RSSI per Cell ID(PCI)
Info>RSSI
EUTRAN>Neighbor Cell
Neighbor Cell RSRP per Cell ID(PCI)
Info>RSRP
EUTRAN>Neighbor Cell
Neighbor Cell RSRQ per Cell ID(PCI)
Info>RSRQ
EUTRAN>Neighbor Cell EARFCN Top 1 to 20 EARFCN from Neighbor Cell
Info>Top Set Cell ID PCI with RSRP strength from top 1 to 20 from Neighbor Cell
RSSI Top 1 to 20 RSSI from Neighbor Cell
RSRP Top 1 to 20 RSRP from Neighbor Cell
RSRQ Top 1 to 20 RSRQ from Neighbor Cell
EUTRAN>All Set All(Serving/Neighbor) Cell EARFCN/RSSI/CINR/RSRP/RSRQ per PCI
EUTRAN>Top Set Cell ID PCI with RSRP strength from top 1 to 20 from Neighbor Cell
EARFCN Top 1 to 20 EARFCN from All(Serving/Neighbor) Cell
RSSI Top 1 to 20 RSSI from All(Serving/Neighbor) Cell
RSRP Top 1 to 20 RSRP from All(Serving/Neighbor) Cell
RSRQ Top 1 to 20 RSRQ from All(Serving/Neighbor) Cell
Top 1 to 20 Cell State from All(Serving/Neighbor) Cell
Cell State
Serving, Neighbor
UTRAN>UARFCN UARFCN per PSC
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
S-measure S-measure
Gap Pattern Gap Pattern
Gap Start SFN Gap Start System Frame Number
Gap Start Subframe Gap Start Subframe
EUTRA quantity EUTRA quantity
EUTRA FC RSRP EUTRA Fc RSRP (where, Fc: Frequency of the carrier centre frequency)
EUTRA FC RSRQ EUTRA Fc RSRQ (where, Fc: Frequency of the carrier centre frequency)
XCAP-LTE Analyzer Parameter Description/Ed.04
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
SI-RNTI SI-RNTI
P-RNTI P-RNTI
Temp C-RNTI Temporary C-RNTI
C-RNTI C-RNTI
RA-RNTI RA-RNTI
SPS-RNTI SPS-RNTI
Parameter Description
Uplink>RB ID [x]>Poll Poll retransmit timer for Uplink (where, x = 0 ~ 31) [Unit: ms]
retransmit timer
Uplink>RB ID [x]>Poll Poll PDU for Uplink (where, x = 0 ~ 31)
PDU
Uplink>RB ID [x]>Poll Poll Byte for Uplink (where, x = 0 ~ 31) [Unit: kB]
Byte
Uplink>RB ID [x]>Max Max Retransmit threshold for Uplink (where, x = 0 ~ 31) [Unit: n]
Retransmit threshold
Uplink>RB ID [x]>Active Active Info for Uplink (where, x = 0 ~ 31)
Info
Downlink>RB ID [x]>UM UM SN length for Downlink (where, x = 0 ~ 31)
SN length
Downlink>RB ID [x]>T1 T1 time value for Downlink (where, x = 0 ~ 31) [Unit: ms]
time value
Downlink>RB ID Status Prohibit timer value for Downlink (where, x = 0 ~ 31) [Unit: ms]
[x]>Status Prohibit timer
value
Downlink>RB ID Active Info for Downlink (where, x = 0 ~ 31)
[x]>Active Info - Deactive
- Active
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Physical Layer>UL
LTE PUSCH Throughput [Unit: Mbps]
Throughput
Physical Layer>DL
LTE PDSCH Throughput [Unit: Mbps]
Throughput
Parameter Description
Parameter Description
SRS Hopping
SRS hopping bandwidth (Range is 0 to 3)
Bandwidth
Freq Domain Position Frequency Domain Position (Range is 0 to 23)
0 corresponds to single and value 1 to indefinite
Duration
(Range is 0 to 1)
Tx Combination Tx Combination (Range is 0 to 1)
Cyclic Shift Cyclic Shift (Range is 0 to 7)
SRS Config Index SRS Config Index (Range is 0 to 1023)
GM Dedicated> PHR 0x0 – Disable
PHR Enabled
Config 0x1 – Enable
PERIODIC_PHR_TIMER Value in number of subframes
Periodic PHR Timer
(Range is 0 to 1000).
PROHIBIT PHR TIMER Value in number of subframes
Prohibit PHR Timer
(Range is 0 to 1000).
DL Pathloss Change DL Pathloss Change Value in dB
Threshold (Range is 0 to 6)
GM Dedicated> PUSCH 0x0 – Disable
PUSCH TPC Enabled
TPC Config 0x1 – Enable
PUSCH TPC DCI 0x0 - Format 3
Format 0x1 – Format 3a
Index of N or M
PUSCH TPC Index N or M is dependent on the used DCI format
(Range is 1 to 31)
RNTI for PUSCH power control using DCI format
PUSCH TPC-RNTI
3/3A
GM Dedicated> PUCCH 0x0 – Disable
PUCCH TPC Enabled
TPC Config 0x1 – Enable
PUCCH TPC DCI 0x0 - Format 3
Format 0x1 – Format 3a
Index of N or M
PUCCH TPC Index N or M is dependent on the used DCI format
(Range is 1 to 31)
RNTI for PUCCH power control using DCI format
PUCCH TPC-RNTI
3/3A
GM Dedicated> UL SCH MAX HARQ
max-HARQ-Tx (Range is 1 to 28)
Config Transmissions
Configures TTI bundling on and OFF; can be configured
TTI Bundling Enabled
for FDD and for TDD only for configurations 0, 1 and 6
GM Dedicated> UL Accumulation-enabled
Power Control Config Accumulation Enabled 1 corresponds to enabled, whereas 0 corresponds to
disabled
P0 UE PUSCH P0 UE PUSCH (Range is -8 to 7)
On Duration Timer
On Duration Timer
pdcch subframes (Maximum value 200)
Inactivity Timer
Inactivity Timer
pdcch subframes (Maximum value 2560)
DL DRX Retx Timer
DL DRX Retx Timer
pdcch subframes (Maximum value 33)
Long Cycle Len
Long Cycle Len
pdcch subframes (Maximum value 2560)
Cycle Start Offset
Cycle Start Offset
pdcch subframes (Maximum value 2559)
Short DRX Cycle 0x0 – Disable
Enable 0x1 – Enable
Short DRX Cycle Len
Short DRX Cycle Len
pdcch subframes (Maximum value 640)
Short DRX Timer
Short DRX Timer
pdcch subframes (Maximum value 16)
PRACH Logical Root ZadOFF-Chu Sequence number for various
preamble formats
Logical Root Seq Index
Range is 0 to 837 for Preamble Format 0-3
Range is 0 to 137 for Preamble Format 4
Random Access Preamble timing for a range of
RA Preamble Timing
Preamble Formats (Range is 0 to 15)
Controls grouping of preamble sequences in two sets, to
High Speed Flag
differentiate a high speed UE from normal
PRACH Frequency
Frequency Resource offset (Range is 0 to 104)
Offset
Max Transmissions Maximum number of HARQ re-transmissions from UE for
MSG3 RACH message3 (Range is 1 to 8)
Cyclic Shifts for various Preamble Formats
Cyclic Shift Zone Length Range is 0 to15 for Preamble Formats 0-3
Range is 0 to 6 for Pramble Format 4
RA Response Window Window size for reception of RACH message2
Size (Range is 2 to 10)
TDD 0 – SUBFRAME_ASSIGN_0
1 – SUBFRAME_ASSIGN_1
2 – SUBFRAME_ASSIGN_2
Subframe Assignment 3 – SUBFRAME_ASSIGN_3
4 – SUBFRAME_ASSIGN_4
5 – SUBFRAME_ASSIGN_5
6 – SUBFRAME_ASSIGN_6
Power Info
Parameter Description
RSSI(In-band) Ant0 RSSI(In-band) for Ant0 (Range: -120 dBm to -10 dBm)
Ant1 RSSI(In-band) for Ant1 (Range: -120 dBm to -10 dBm)
Comb [RSSI(In-band)>Ant0 + RSSI(In-band)>Ant1]/2
RSSI(Total Band) Ant0 RSSI(Total Band) for Ant0 (Range: -120 dBm to -10 dBm)
Ant1 RSSI(Total Band) for Ant1 (Range: -120 dBm to -10 dBm)
Comb [RSSI(Total Band)>Ant0 + RSSI(Total Band)>Ant1]/2
RSSI(Broadband) Ant0 RSSI(Broadband) for Ant0 (Range: -120 dBm to -10 dBm)
Ant1 RSSI(Broadband) for Ant1 (Range: -120 dBm to -10 dBm)
Comb [RSSI(Broadband)>Ant0 + RSSI(Broadband)>Ant1]/2
Tx Power PUSCH PUSCH Tx Power (Range: -112 dBm to 23 dBm)
PUCCH PUCCH Tx Power (Range: -112 dBm to 23 dBm)
PRACH PRACH Tx Power (Range: -112 dBm to 23 dBm)
SRS SRS Tx Power (Range: -112 dBm to 23 dBm)
AGC AGC Tx Power (Range: -70 dBm to 32.3 dBm)
Cell Search
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Parameter Description
Random Access
Request(MSG1)> Preamble Sequence Index.
Preamble Sequence
Random Access
Physical Root Sequence Index corresponding to
Request(MSG1)>
Preamble Sequence
Physical Root Index
Random Access
Request(MSG1)> Cyclic Cyclic Shift
Shift
Random Access
Request(MSG1)> PRACH Transmit Power (Range is -112 dBm to 23 dBm)
PRACH Tx Power
Random Access
Request(MSG1)> Beta Beta PRACH (Range is 0 to 2047)
PRACH
Random Access
Request(MSG1)>
N_ra_prb (Range is 0 to 104)
Frequency Resource
Offset
Random Access
Request(MSG1)> Preamble format (based on PRACH configuration parameter signaled).
Preamble Format
Random Access System Duplex Mode
Request(MSG1)> 0: FDD
Duplex Mode 1: TDD
Density per 10 ms
0x0: 0.5
0x1: 1
0x2: 2
d_ra
0x3: 3
0x4: 4
0x5: 5
0x6: 6
Random Access
Random Access Response Timing - System frame number
Response(MSG2)> SFN
Random Access
Response(MSG2)> Random Access Response Timing - Subframe number
Sub-Fn
Random Access
Response(MSG2)> Timing Advance Value
Timing Advance
Random Access
0x0 – Contention free
Response(MSG2)>
0x1 – Contention based
RACH Procedure Type
Random Access
0x0 – Initial access
Response(MSG2)>
0x1 – Connected mode RACH procedure
RACH Procedure Mode
Random Access 0x0 – C_RNTI
Response(MSG2)> 0x1 – SPS_RNTI
RNTI Type 0x2 – P_RNTI
0x3 – RA_RNTI
0x4 – TEMP_C_RNTI
0x5 – SI_RNTI
0x6 – TPC_PUSCH_RNTI
0x7 – TPC_PUCCH_RNTI
0x8 – MBMS RNTI
Random Access
Response(MSG2)> RNTI value
RNTI Value
UE
Identification(MSG3)> TPC command to be applied to MSG3 transmission
TPC
UE
Identification(MSG3)> Modulation and Coding Scheme
MSC
UE
Identification(MSG3)> Resource Indicator Value
RIV
Contention
0x0 – Contention failed
Resolution(MSG4)>
0x1 – Contention passed
Contention Result
Contention
Resolution(MSG4)> UL System frame number of MSG4 ACK
ACK Timing SFN
Contention
Resolution(MSG4)> UL Subframe number of MSG4 ACK
ACK Timing Sub-Fn
Parameter Description
Out of Sync BLER Out of Sync BLER, calculated from the measured SNR. The out_sync BLER
corresponds to the BLER if the actual transmission parameters equal to the
parameters specified in Spec for out_sync.
x / (1<<15) * 100(%)
In Sync BLER In Sync BLER, calculated from the measured SNR. The in_sync BLER corresponds
to the BLER if the actual transmission parameters equal to the parameters specified
in Spec for in_sync.
x / (1<<15) * 100(%)
Parameter Description
Parameter Description
XCAP-LTE Analyzer Parameter Description/Ed.04
Parameter Description
Parameter Description
PLMN Search Request> Allowed access on the cell based on network select mode indicated by NAS
NETWORK_SELECT_ 1 - Automatic
MODE 2 - Manual
PLMN Search Request> Service Search type indicated by NAS
SEARCH_TYPE 1 – None
2 – Background Automatic
3 - Background Manual
PLMN Search Request> 1 – GSM
RAT_LIST> List[x] 2 – WCDMA
3 – LTE
PLMN Search Request>
MCC and MNC
PLMN_LIST> List[x]
PLMN Search Active RAT
Response> Active RAT 1 – GSM
2 – WCDMA
3 – LTE
PLMN Search 1 – Completed
Response> 2 – Timed out
SEARCH_STATUS 3 – Abort Confirmation
4 - Aborted
XCAP-LTE Analyzer Parameter Description/Ed.04
PLMN Search
Response> MCC and MNC
PLMN_LIST> List[x]
Parameter Description
Physical Throughput
Parameter Description
PDSCH Throughput>
∑PDSCH Throughput>HARQ[x] (Unit: Mbps)
Total
PDSCH Throughput>
(within 1 second ∑pdsch_tb_size)*8/(1sec)/(10^6) (Unit: Mbps)
HARQ[#]
PUSCH Throughput>
∑PUSCH Throughput>HARQ[x] (Unit: Mbps)
Total
MAC Throughput
Parameter Description
DL MAC Throughput>
∑DL MAC Throughput>HARQ[x] (Unit: Mbps)
Total
DL MAC Throughput>
(within 1 second ∑MAC DL TBS)*8/(1 sec)/(10^6) (Unit: Mbps)
HARQ[#]
UL MAC Throughput>
∑UL MAC Throughput>HARQ[x] (Unit: Mbps)
Total
UL MAC Throughput>
(within 1 second ∑MAC UL GRANT(BYTE))*8/(1 sec)/(10^6) (Unit: Mbps)
HARQ[#]
RLC Throughput
Parameter Description
DL RLC Throughput>
∑DL RLC Throughput>RB CFG IDX[x] (Unit: Mbps)
Total
DL RLC Throughput> (∆RLC Rx Byte)*8/(∆Timestamp)/(10^6) (Unit: Mbps)
RB CFG IDX[#] Where, RLC Rx Byte = DATA_PDU_BYTES + STATUS_RXED_BYTES +
INVALID_PDU_BYTES
UL RLC Throughput>
∑UL RLC Throughput>RB CFG IDX[x] (Unit: Mbps)
Total
UL RLC Throughput> (∆RLC Tx Byte)*8/(∆Timestamp)/(10^6) (Unit: Mbps)
RB CFG IDX[#] Where, RLC Tx Byte = NUM_NEW_DATA_PDU_BYTES +
NUM_CTRL_PDU_BYTES_Tx + NUM_RETX_PDU_BYTES
PDCP Throughput
Parameter Description
DL PDCP Throughput>
∑DL PDCP Throughput>RB CFG IDX[x] (Unit: Mbps)
Total
DL PDCP Throughput> (∆PDCP Rx Byte)*8/(∆Timestamp)/(10^6) (Unit: Mbps)
RB CFG IDX[#] Where, PDCP Rx Byte = NUM_DATA_PDU_RX_BYTES +
NUM_CONTROL_PDU_RX_BYTES + NUM_PDU_INVALID_BYTES
UL PDCP Throughput>
∑UL PDCP Throughput>RB CFG IDX[x] (Unit: Mbps)
Total
XCAP-LTE Analyzer Parameter Description/Ed.04
L1 status information shows physical layer status such as channel setup status, serving cell information,
PCH DRX and measurement periodicity, etc.
Parameter Description
The serving cell quality information shows SNR of reference signal (RS SNR) and received power of
reference signal (RS RSSI).
Parameter Description
Tx Power Info
Time sync report log shows the time sync status of UE.
Parameter Description
RACH Info
Parameter Description
Parameter Description
Cell Info
Cell Information display cell lists which are collected from Mp Searcher and Cell Searcher.
Parameter Description
INTRA>SYNC> RSRP Reference Signal Received Power of Intra cell which is known the sync position.
INTRA>SYNC> RSRQ Reference Signal Received Quality of Intra cell which is known the sync position
INTRA>SYNC> RSSI Received Power of Intra cell which is known the sync position
INTRA>SYNC>
Cell frame boundary in Intra Sync
FrameBound
INTRA>SYNC> CP length in Intra Sync
CPLength 0: Unknown
1 : Normal CP
2 : Extended CP
INTRA>SYNC> DL
Earfcn number in Intra Sync
Earfcn
INTRA>SYNC> Top Set PCI PCI with RSRP strength from top 1 to 20 from Intra Sync Cell
RSRP Top 1 to 20 RSRP from Intra Sync Cell
RSRQ Top 1 to 20 RSRQ from Intra Sync Cell
RSSI Top 1 to 20 RSSI from Intra Sync Cell
FrameBound Top 1 to 20 FrameBound from Intra Sync Cell
CPLength Top 1 to 20 CPLength from Intra Sync Cell
DL Earfcn Top 1 to 20 DL Earfcn from Intra Sync Cell
INTRA>ASYNC> RSRP Reference Signal Received Power of Intra cell which is unknown the sync position.
INTRA> ASYNC>
Reference Signal Received Quality of Intra cell which is unknown the sync position
RSRQ
INTRA> ASYNC> RSSI Received Power of Intra cell which is unknown the sync position
INTRA> ASYNC>
Cell frame boundary in Intra Async
FrameBound
INTRA> ASYNC> CP length in Intra Async
CPLength 0: Unknown
1 : Normal CP
2 : Extended CP
INTRA> ASYNC> DL
Earfcn number in Intra Async
Earfcn
INTRA> ASYNC > Top PCI PCI with RSRP strength from top 1 to 20 from Intra Async Cell
Set RSRP Top 1 to 20 RSRP from Intra Async Cell
XCAP-LTE Analyzer Parameter Description/Ed.04
All Set All Cell RSRP/RSRQ/RSSI/FrameBound /CPLength/DL Earfcn/Cell State per PCI
Top Set PCI PCI with RSRP strength from top 1 to 20 from All Cell
RSRP Top 1 to 20 RSRP from All Cell
RSRQ Top 1 to 20 RSRQ from All Cell
RSSI Top 1 to 20 RSSI from All Cell
FrameBound Top 1 to 20 FrameBound from All Cell
CPLength Top 1 to 20 CPLength from All Cell
DL Earfcn Top 1 to 20 DL Earfcn from All Cell
Top 1 to 20 Cell State from All Cell
- Intra Sync
- Intra Async
Cell State - Intra Detect
- Inter Sync
- Inter Async
- Inter Detect
Search Result
Search Result log shows Mp Search result and Cell Search result.
Parameter Description
Channel Info
Parameter Description
Tx Correlation> Freq
Tx Correlation in Total Band(Sub Band 1 ~ 30)
Total Band(Avg)
Tx Correlation> Freq
Tx Correlation per Sub Band
Sub Band x
CQI Info
The wideband CQI information shows measured CQI of wideband in the UE.
The sub-band CQI information shows the CQI (channel quality information) of sub-bands. The sub-band is
defined a unit for a group of resource elements used for reporting sub-band CQI.
Parameter Description
CQI(Subband)> Rank2
Rank2 sub band CQI for CW0
CW0 CQI
CQI(Subband)> Rank2
Rank2 sub band CQI for CW1
CW1 CQI
CQI(Subband)> Rank1
Rank1 sub band PMI
PMI
CQI(Subband)> Rank2
Rank2 sub band PMI
PMI
Multi-paths Profile
This information shows the channel impulse response of reference signals in the time domain.
Parameter Description
PBCH BLER
PBCH BLER displays how much transport blocks get CRC_NOK about total received transport blocks.
Parameter Description
PDSCH BLER
PDSCH BLER displays how much transport blocks get CRC_NOK about total received transport blocks.
Parameter Description
UE can’t calculate PDCCH BLER because UE doesn’t know when eNode-B sends its PDCCH. In other
words, UE detects PDCCH blindly. So, UE DM supports this item similar with PDCCH BLER.
Parameter Description
DL Grant & UL ACK/NACK Status(Improved) displays DL grant regardless any DCI format in every TTI.
According to TS36.212, each DCI format has the specific fields, not all, and the unnecessary fields are
displayed to the blank. Additionally, UL_ACK/NACK, CFI, and DCI_3/3A payload will be included in this
item.
Parameter Description
DL Grant & UL Ack/Nack Status Info(Improved)[Detail per TTI] displays the related information per TTI.
Parameter Description
UL ACK/NACK
UL ACK/NACK result in CW0
Result(CW0)
DCI 3(CW0) DCI3/3A value in CW0
MCS(CW1) MCS in CW1
NDI(CW1) NDI in CW1
RV(CW1) redundancy version in CW1
MOD Type(CW1) modulation type in CW1
New/Retrans
new or retransmission type in CW1
Type(CW1)
TB Size(CW1) transport block size in CW1
CRC Result(CW1) CRC result in CW1
UL ACK/NACK
UL ACK/NACK result in CW1
Result(CW1)
DCI 3(CW1) DCI3/3A value in CW1
UL Grant Info Status log shows get UL Scheduling Grant information to PDCCH.
Parameter Description
UL Grant & DL Ack/Nack Status info[Detail per TTI] displays the related information per TTI.
Parameter Description
PDSCH PHY Throughput has displays how much to get the downlink data in 1sec.
Parameter Description
This information shows the log of transmit physical resource mapping information.
Parameter Description
Parameter Description
L2 DL Throughput
Parameter Description
L2 UL Throughput
Parameter Description
This item is for MAC BLER of downlink (PDSCH). Ratio of transport blocks which remain un-
XCAP-LTE Analyzer Parameter Description/Ed.04
acknowledged (CRC failure) after HARQ retransmission divided by total number of initial transmissions
received by UE MAC
Parameter Description
Parameter Description
Tx States> RB ID (x)>
Tx States RLC Mode (AM /UM/TM)
Mode
Tx States> RB ID (x)>
Tx States RLC Tx Entity state (NULL/DTR)
State
Rx States> RB ID (x)>
Rx States RLC Mode (AM /UM/TM)
Mode
Rx States> RB ID (x)>
Rx States RLC Tx Entity state (NULL/DTR)
State
Parameter Description
Parameter Description
Parameter Description
RACH Response
RACH response receiving time
Receiving Time
Result 0: NACK, 1: ACK
RACH Preamble Identity RACH Preamble Identity
BackOff Indicator BackOff Indicator
Time Advance Time Advance
Temporary C-RNTI Temporary C-RNTI
MCS Modulation and coding Scheme
TPC for scheduled
TPC command for scheduled PUSCH
PUSCH
Hopping Flag Hopping Flag
UL Delay UL Delay
CQI Request CQI Request
Resource Block
Resource block assignment(10bits)
Assignment
Access RACH Latency Access RACH Latency (sec)
RNTI Info
Parameter Description
C-RNTI C-RNTI
Parameter Description
Parameter Description
Parameter Description
This item provides the state information of EMM (EPS Mobility Management), ECM (EPS Connection
Management) and PLMN and EU (EPS Update) status when each state is changed.
Parameter Description
This item provides the NAS state information of EMM (EPS Mobility Management), ECM (EPS Connection
Management) and PLMN and EMM Cache status when each state is changed.
Parameter Description
Parameter Description
Parameter Description
This item provides the information on both source cell and target cell when RRC perform cell reselection.
Parameter Description
Handover History
Parameter Description
Parameter Description
This item includes ESM instance information R3. Maximum number of ESM instance is 15(1~15). The
EPS Id uniquely identifies each ESM instance.
Parameter Description
st nd th
Tab Index 1: 1 tab, 2: 2 tab, … 15: 15 tab
EPS Id EPS ID
Linked Bearer Id Linked Bearer ID
PDN Address PDN IP Address
APN Access Point Name
QCI QCI (1 ~ 9)
EPS Type - NONE BEARER TYPE
- DEFAULT_BEARER
- DEDICATED_BEARER
ESM State - DEACTIVE
- ACTIVE
PTI PTI
Instance Id Instance ID