Professional Documents
Culture Documents
Garage Door Opener Installation Manual
Garage Door Opener Installation Manual
INTRODUCTION....................................................................3
Tools needed........................................................................5
Assemble the Rail................................................................6
Garage door opener assembly.........................................10
Hardware..............................................................................10
Fasten the Rail to the garage door opener......................12
Determine the Header Bracket Location...........................13
Install the Header Bracket...................................................15
Connect the Rail to the Header Bracket..............................17
Position the garage door opener..........................................18
Hang the garage door opener............................................19
Attach the Emergency Release Rope and Handle...............20
Install the door bracket.......................................................21
Connect the door arm to the trolley.....................................23
Install the Wall Control.....................................................25
Attach the Warning Labels...............................................28
Install The Photo Eye Safety System............................29
Power and adjustments...................................................33
Programming and adjustment..........................................34
Programming buttons...........................................................34
Preparation...........................................................................34
Connect Power.....................................................................34
Program the travel................................................................35
Remote Control....................................................................36
To Erase the Memory...........................................................37
The adjustment of reverse force.........................................38
Circuit board.........................................................................40
Use photoelectric switches...................................................41
Turn off light automatically...............................................42
Power failure clutch lock...................................................42
Backup battery..................................................................42
Door within a Door...........................................................43
Maintenance and repair.....................................................43
Technical parameter..........................................................43
Trouble shooting................................................................44
2
INTRODUCTION
This garage door opener has been designed and tested to offer
safe service provided it is installed, operated, maintained and
tested in strict accordance with the instructions and warnings
contained in this manual. When you see these Safety Symbols and
Signal Words on the following pages, they will alert you to the
possibility of serious injury or death if you do not comply with the
warnings that accompany them.
The hazard may come from something or from electric shock. Read
the warnings carefully.
When you see this Signal Word on the following pages, it will alert
you to the possibility of damage to your garage door and/or the
garage door opener if you do not comply with the cautionary
statements that accompany it. Read them carefully.
3
5. The opener should be installed above the center of the
door. If there is a torsion spring or center bearing plate in
the way of the header bracket, it may be installed within 4
feet (1.2 m) to the left or right of the door center. See
Installing the Header Bracket section.
4
Tools needed
5
1、Assemble the Rail
Rail Accessories
6
Assemble the Rail
7
Assemble the Rail
RailAssembly
Rail
Rail Assembly
Assembly
1.1、Remove the three rail sections and place them on
1.1、Removethe
1.1、Remove
1.1、Remove thethree
the threerail
three railsections
rail sectionsand
sections andplace
and place them
place them on
on
floor.
floor.
floor.
Three holes
Three holes rail
rail
Three holes rail
Center rail
Center rail Seven holes rail
Center rail Seven holes rail
1.2、Rail connectors
1.2、Rail
1.2、Rail connectors
connectors installation.
installation.
installation.
1.2、Rail connectors installation.
A3
A3
A3
A1
A1
A1
A2
A2
A2 A4
A4
A4
1.3、Spread carefully
1.3、Spread carefully the
the chain/belt
chain/belt straight
straight inside
inside the
the rail.
rail. Check
Check
1.3、Spread
1.3、Spread carefully the chain/belt
carefully the straight
chain/belt inside the
straight rail. Check
inside the rail.
to be
to be sure
sure the
the chain
chain is
is not
not twisted.
twisted.
Check
to to the
be sure be chain
sure the chain
is not is not twisted. Note: Make sure the
twisted.
Note: Make
Note: Make sure
sure the
the chain
chain engage
engage the
the 10-tooth
10-tooth sprocket
sprocket as
as shown.
shown.
chain
Note: engage
Make surethe
the10-tooth sprocket
chain engage the as shown.
10-tooth sprocket as shown.
66
6
8
Assemble the Rail
Rail
1.4 Assembly
Screw and lock washer installation.
1.4、Screw and lock washer installation.
Rail Assembly
1.4、Screw
Rail and lock washerA6
Assembly (2)
installation. A5(2)
1.4、Screw and lock washer installation.
A6(2) A5(2)
A6(2) A5(2)
1.5、Tightenthe
1.5、Tighten theChain
Chain
1.5.1 To increase the tension and tighten the chain, turn the tension
1.5.1 To increase
1.5、Tighten
the tension and tighten the chain, turn the
the Chainor adjustable wrench until the nut is spaced
nut clockwise
tension nut clockwise or adjustable wrench until the nut is spaced
1.5、Tighten
properly the
theChain
1.5.1 Toproperly from
increase
from the
theend
rail rail
tension end
and-plate.
-plate. tighten the chain, turn the tension
1.5.2
1.5.1 nut Once
Toclockwise
increasethethenutadjustable
or is spaced
tension and correctly,
wrench any
until
tighten the additional
the nut turn
chain, tightening
is spaced
the tension will
1.5.2 Once
over
properly
nut the nut
tighten is
from the
clockwise or spaced
theadjustable
chain
rail correctly,
endand any
may cause
-plate.
wrench additional
damage
until the nut isto tightening
the system.
spaced will
over tighten the chain and may cause damage to the system.
1.5.3
1.5.2 Once To the
properly loosenutthe
from tension,
is spaced turn nut counterclockwise.
rail end correctly,
-plate. any additional tightening will
1.5.2over
1.5.3 ToOncetighten
loose the the chain
nuttension,
the and
is spaced may nutcause
correctly,
turn damage
any to the
additional
counterclockwise. system. will
tightening
1.5.3over
Totighten
loose the tension, turn nut counterclockwise. 25mm
the chain and may cause damage to the system.
1.5.3 To loose the tension, turn nut counterclockwise.
25mm
25mm
7
9 7
Garage door opener assembly
Hardware
10
Garage door opener assembly
11
Garage door opener assembly
12
Garage door opener assembly
2.1 Close the door and mark the inside vertical centerline of the
garage door.
2.2 Extend the line onto the header wall above the door.
You can fasten the header bracket within 4 feet (1.22 m) of the
left or right of the door center only if a torsion spring or center
bearing plate is in the way; or you can attach it to the ceiling
when clearance is minimal. (It may be mounted on the wall
upside down if necessary, to gain approximately 1/2" (1 cm).
If you need to install the header bracket on a 2x4 (on wall or
ceiling), use lag screws (not provided) to securely fasten the 2x4 to
structural supports.
2.3 Open your door to the highest point of travel as shown. Draw
an intersecting horizontal line on the header wall above the high
point: 2" (5 cm) above the high point for sectional door with track.
NOTE: If the total number of inches exceeds the height available in
your garage, use the maximum height possible.
13
Garage door opener assembly
14
3、Install the Header Bracket You can attach the header bracket
either to the wall above the garage door, or to the ceiling. Follow
the instructions which will work best for your particular
requirements. Do not install the header bracket over drywall. If
installing into masonry, use concrete anchors (not provided).
3.1A Center the bracket on the vertical centerline with the bottom
edge of the bracket on the horizontal line as shown (with the arrow
pointing toward the ceiling).
3.2A Mark the holes. Drill 3/16" pilot holes and fasten the bracket
securely to a structural support with the hardware provided.
15
Option B CEILING INSTALLATION
3.2B Center the bracket on the vertical mark, no more than 6" (15
cm)
3.3B from the wall. Make sure the arrow is pointing away from the
wall. The bracket can be mounted flush against the ceiling when
clearance is minimal.
3.4B Mark the holes. Drill 3/16" pilot holes and fasten bracket
securely to a structural support with the hardware provided.
16
4、Connect the Rail to the Header Bracket
Align the rail to the header bracket, fasten with the bolts and nuts
(H1) (H2) as shown below.
HARDWARE
17
5、Position the garage door opener
NOTE: A 2x4 is ideal for setting the distance between the rail and
the door. If the ladder is not tall enough you will need help at this
point.
If the door hits the trolley when it is raised, pull the trolley release
arm down to disconnect the chain connector kit and trolley. Slide
the trolley toward the garage door opener. The trolley can remain
disconnected until further instruction.
18
6、Hang the garage door opener
19
7、Attach the Emergency Release Rope and Handle
7.1 Insert one end of the emergency release rope through the
handle. Tie a knot at least 1 inch (2.5 cm) from the end of the
emergency release rope.
7.2 Insert the other end of the emergency release rope through the
hole in the trolley release arm. Make sure the handle is 6 feet (1.83
m) above the floor and secure with a knot.
20
8、Install the door bracket
Figure 1 shows one piece of angle iron as the horizontal brace. For
the vertical brace, 2 pieces of angle iron are used to create a U-
shaped support. The best solution is to check with your garage
door manufacturer for an opener installation door reinforcement kit.
21
A horizontal and vertical reinforcement is needed for
lightweight garage doors (fiberglass, aluminum, steel, doors
with glass panel, etc.) (not provided). A horizontal
reinforcement brace should be long enough to be secured to
two or three vertical supports. A vertical reinforcement brace
should cover the height of the top panel.
Option SECTIONAL DOORS
8.2 Position the top edge of the bracket 2"-4" (5-10 cm) below the
top edge of the door, OR directly below any structural support
across the top of the door.
· Drill 3/16" fastening holes. Secure the door bracket using the two
self-threading screws (C2). (Figure 2)
· Alternately, use two 5/16" bolts, lock washers and nuts (not
provided). (Figure 3)
22
9、Connect the door arm to the trolley
HARDWARE
9.1 9.2
23
9.2 Attach the curved door arm to 9.4
the door bracket using the
shouldered shaft (H2). Attach with
the cotter (H5).
NOTE: If the straight door arm is hanging down too far, you may
cut 6 inches (15 cm) from the solid end.
24
10、Install the Wall Control
INTRODUCTION
Install the wall control within sight of the door at a minimum height
of 5 feet (1.5 m) where small children cannot reach, and away from
the moving parts of the door. Your product may look different than
the illustrations.
25
a
26
c
a
a
a
b
a
27
11、 Wire the wall control to the garage door opener
11.1 Strip 7/16 inch (11 mm) of insulation from one end of the wire
and separate the wires.
11.2 Connect the white wire to the GND terminal and the red\white
wire to the PBSW terminal on garage door opener.
28
12、 Attach the warning labels
12.1 Attach the entrapment warning label on the wall near the door
control with tacks or staples.
Introduction
29
The sending sensor (with a red LED) transmits an invisible light
beam to the receiving sensor (with a green LED). If an obstruction
breaks the light beam while the door is closing, the door will stop
and reverse to the full open position, and the garage door opener
lights will flash three minutes
NOTE: For energy efficiency the garage door opener will enter
sleep mode when the door is fully closed. The sleep mode shuts
the garage door opener down until activated. The sleep mode is
sequenced with the garage door opener light bulb; as the light bulb
turns off the sensor LEDs will turn off and whenever the garage
door opener lights turn on the sensor LEDs will light. The garage
door opener will not go into the sleep mode until the garage door
opener has completed 5 cycles upon power up.
· Sensors are installed inside the garage, one on either side of the
door.
· Sensors are facing each other with the lenses aligned and the
receiving sensor lens does not receive direct sunlight.
· Sensors are no more than 6 inches (15 cm) above the floor and
the light beam is unobstructed.
30
Install the Photo Eye Safety System 1、Install the Safety
Reversing Sensors
Position the mounting bracket against the wall with the curved arms
facing the door. Make sure there is enough clearance for the beam
to be unobstructed. Attach the mounting bracket to the wall using
lag screws.
Strip 7/16 inch (11 mm) of insulation from each set of wires.
Separate the wires. Twist the white wires together. Twist the
white/red wires together.
31
Insert the white wires into the GND terminal on the garage door
opener. Insert the white/red wires into the PB terminal on the
garage door opener.
Ensure the Safety Reversing Sensors are aligned The door will
not close if the sensors have not been installed and aligned
correctly.
Check to make sure the LEDs in both sensors are glowing steadily
.The LEDs in both sensors will grow steadily if they are aligned and
wired correctly.
32
Power
Connect power
33
Adjustments
34
Programming and adjustment
a) Programming buttons
b) Preparation:
Move the door to lock the trolley so that the opener can
drive the door when adjustment.
c) Connect Power:
Puts through the power source, the LED display from “9” to
“1”.
If the number direction displayed on LED is opposite, press
button “SETTING”, the LED displayed would be inverted,
then display again from “9” to “1”.
35
d) Program the travel
NOTE: The UP and DOWN Buttons can be used to move the door
up and down as needed.
36
e) Remote Control
To open or close the garage door, press and hold button. When the
garage door move, release button. To stop garage door during
travel, press and hold button until door stops, the release button.
37
f) To Erase the Memory
Press and hold the CODE button on garage door opener, the “●”
will turn on. Release the CODE button when the “●” turns off. All
remote control are now erased. Reprogram any accessory you
wish to use.
38
g) The adjustment of reverse force
39
Close door automatically
CODE
Press and hold the “+
SETTING
”Button until the screen
show the “—”
+ _
screen 1 2 3 4 5 6 7 8 9
minute 1 2 3 4 5 6 7 8 9
40
h) Circuit board
41
i) Use photoelectric switches
42
Turn off light automatically
It has turned off light function so do not need to set. When the
opener is running, the light is brighten automatically .If have no wall
switch and press any button in 3 minutes, the light will be off
automatically.
Backup battery
43
Door within a Door
Technical parameter
b. Motor: 24VDC
44
Trouble shooting
45