Professional Documents
Culture Documents
Nilfi SK C 100.5 Nilfi SK C 110.3, C 110.3 X-TRA: User Manual
Nilfi SK C 100.5 Nilfi SK C 110.3, C 110.3 X-TRA: User Manual
5
Nilfisk C 110.3, C 110.3 X-TRA
User Manual
Index
1 Safety precautions and warnings .............................................3
2 Description ...............................................................................5
3 Before you start using your pressure washer ...........................6
4 Operating your pressure washer ..............................................7
5 After using your pressure washer .............................................9
6 Maintenance ...........................................................................10
7 Trouble shooting .....................................................................12
8 Further information .................................................................13
9 Technical data ........................................................................14
10 Declaration .............................................................................14
3
safety only use original spare 1.0 mm² max. 12.5 m backflow preventer has been
parts from the manufacturer 1.5 mm² max. 20 m installed, Type BA according
or approved by the manufac- 2.5 mm² max. 30 m to EN 1717. The backflow pre-
turer. venter can be ordered under
High pressure hoses, fittings If the electric cable is number 106411177. The length
and couplings are important damaged, it must be re- of the hose between the back-
for the safety of the appli- placed by the manufacturer flow preventer and the high
ance. Only use hoses, fittings or his service agent or simi- pressure washer must be at
and couplings recommended larly qualified person in order least 10 metres to absorb pos-
by the manufacturer. to avoid a hazard. sible pressure peaks (min diam-
Do not use the appliance eter ½ inch).
if a supply cord or impor- Mains power connection Operation by suction (for ex-
tant parts of appliance are ample from a rainwater vessel)
damaged, e.g. safety device , is carried out without backflow
high pressure hose and trig- preventer. Recommended suc-
ger gun. tion set: 126411387.
The appliance is intended to The following should be ob- As soon as water has flown
clean cars and garden etc.. served when connecting the through the BA valve, this water
Appropriate ear protection high pressure washer to the is not considered to be drinking
has to be used. electric installation: water any more.
Never use the machine in The electric installation shall
an environment where there be made by a certified elec- IMPORTANT! Only use wa-
could be a danger of explo- trician and comply with IEC ter without any impurities. If
sion. If any doubt arises, 364. there is a risk of running sands
please contact the local It is recommended that the in the inlet water (i.e. from your
authorities. electric supply to this appli- own well), an additional filter
It is not allowed to clean as- ance should include either a should be mounted.
bestos-containing surfaces residual current device that
with high pressure. will interrupt the supply if the Safety devices
This high pressure washer leakage current to earth ex- The unloader valve can re-
must not be used at tempera- ceeds 30 mA for 30 ms. duce pressure if it exceeds
tures below 0°C. pre-set values.
Water connection
WARNING! Connection to the public Locking device on spray gun
Inadequate extension cables mains according to regula- (7a) (see illustration at the end
can be dangerous. Cables on tions. of this manual):
drums should always be com- Inlet hose can be connected The spray gun features a lock-
pletely unwinded to prevent the to the water mains with a ing device. When the pawl is
cable from overheating. max. inlet pressure of 10 activated, the spray gun cannot
bars. be operated.
If an extension cable is used,
the plug and the socket must be This high pres- Thermal sensor:
waterproof and comply with the sure washer is A thermal sensor protects the
below-mentioned requirements only allowed to be motor against overloading. The
for length and cable dimen- connected with machine will restart after a few
sions. the drinking water minutes when the thermal sen-
mains, when an appropriate sor has cooled.
4
2 Description
2.1 Application This high-pressure washer has Only use the high-pressure
been developed for domestic washer for purposes described
use within: in this manual.
5
3 Before you start using your
pressure washer
6
4 Operating your pressure washer
Warning: When
attaching the Click
& Clean nozzles,
the pawl on the
side of the spray
lance (6) should come out
again.
7
4.3 Water connection An ordinary 1/2" garden hose of IMPORTANT! Only use wa-
min. 10 m and max. 25 m will ter without any impurities. If
be suitable. there is a risk of running sands
in the inlet water (i.e. from
NOTE: Connection to the public your own well), an additional
mains according to regulations. filter (106411231) should be
mounted.
4.4 Start and stop of the The spray lance is affected Do not cover the machine
machine by a thrust during operation during operation or use it in a
- therefore always hold it firmly room without adequate ventila-
with both hands. IMPORTANT: tion !
Point the nozzle at the
ground. Note: If the ma-
chine is left or not
1. Check that the machine is in used for 5 min-
uprigth position. utes, it must be switched off on
NOTE: Do not place the ma- the start/stop switch "O" (1):
chine in high grass!
2. Release the trigger lock (7a). 1. Press the start/stop switch
3. Activate the trigger of the "O".
spray gun and let the water 2. Disconnect the electrical plug
run until all air has escaped from the socket.
from the water hose. 3. Shut off the water supply and
4. Press the Start/stop switch activate the trigger to relieve
"I" (1). the machine of pressure.
5. Activate the trigger of the 4. Lock the spray gun (7a).
spray gun.
When releasing the trigger of
Always adjust the distance and the spray gun, the machine
thus the pressure of the nozzle automatically stops. The ma-
to the surface, which is to be chine will start again when you
cleaned. re-activate the spray gun.
8
5 After using your pressure washer
5.1 Storing the washer The machine should be sto- 3. Stop the machine, unplug
red in a frost-free room! and wind up hose and cable.
4. Place spray handle, nozzles
Pump, hose and accessories and other accessories in the
should always be emptied of holders of the machine.
water prior to storing as follows:
Should the machine by mistake
1. Stop the machine (press the be frozen, it will be necessary
start/stop switch “O” (1) and to check it for damage.
detach water hose and ac-
cessory. NEVER START-UP A FROZEN
2. Restart the machine and MACHINE.
activate the trigger. Let the
machine run until no more Frost damages are not
water runs through the spray covered by the guarantee!
gun.
9
6 Maintenance
10
6.3 Cleaning of machine The machine should be kept
vents clean so as to let cooling air
pass freely through the ma-
chine vents.
11
7 Trouble-shooting
To avoid unnecessary disappointments, you should check the following before contacting the Nilfisk
service organization:
In case problems other than the above occur, please contact your local Nilfisk distributor.
12
8 Further information
8.1 Recycling the washer Make the old cleaner unusable As specified in European Direc-
immediately. tive 2002/96/EC on old electri-
cal and electronic appliances,
1. Unplug the cleaner and cut used electrical goods must
the electric cable. be collected separately and
recycled ecologically.
Do not discard electrical appli-
ances with household waste. Contact your local authorities or
your nearest dealer for further
information.
8.2 Warranty conditions Nilfisk guarantees high pres- that only water without any
sure washers for domestic use impurities has been used.
for 2 years. If your high pres- that the high pressure
sure washer or accessories are washer has not been used
handed in for repair, a copy of for rental nor used commer-
the receipt must be enclosed. cially in any other way.
Guarantee repairs are being
made on the following condi- Repairs under this guarantee
tions: include replacement of defec-
that defects are attributable tive parts, exclusive of packing
to flaws or defects in materi- and postage/carriage. Besides,
als or workmanship. (wear we refer to your national law of
and tear as well as misuse sale.
are not covered by the
guarantee). The machine should be for-
that the directions of this warded to one of the service
instruction manual have been centres of the Nilfisk organisa-
thoroughly observed. tion with description/specifica-
that repair has not been tion of the fault.
carried out or attempted by
other than Nilfisk-trained Repairs not covered by the
service staff. guarantee conditions will be
that only original accessories invoiced. (I.e. malfunctions due
have been applied. to Causes mentioned in section
that the product has not been Troubleshooting Chart of the
exposed to abuse such as instruction manual).
knocks, bumps or frost.
13
9 Main Technical Data
Type C 100.5-5 C 110.3-5 C 110.3-5 X-TRA
bar/
Rated pressure 70/7.0 75/7.5 75/7.5
MPa
bar/
Permissible pressure max. 100/10.0 max. 110/11.0 max. 110/11.0
MPa
Rated flow l/min 5.3 5.2 5.2
Rated input kW 1.3 1.4 1.4
Rated voltage V 230-240 230-240 230-240
Max. water temperature °C 40 40 40
bar/
Inlet pressure 0.15-10/0.015-1.0 0.15-10/0.015-1.0 0.15-10/0.015-1.0
MPa
Sound pressure level dB(A) 78 78 78
Guaranteed sound power level dB(A) 93 93 93
Vibration according to ISO 5349 m/s2 max. 2.5 max. 2.5 max. 2.5
10 Declaration
Declaration
Manufacturer's name and address or his Nilfisk-Advance A/S
authorized representative in the Community Industrikvarteret
9560 Hadsund
Denmark
Name of the person responsible for the Anton Sørensen, General Manager of Technical Operations EAPC
technical documentation
Declaration The equipment refer in this document fulfils all the requirements of
the Directive :
Machine Directive 2006/42/EC
Low-voltage Directive 2006/95/EEC
EMC Directive 2004/108/EEC
Outdoor Noise Directive 2000/14/EC
EN ISO 12100-1, EN ISO 12100-2, EN 60335-2-79
EN 55014-1 (2006), EN 55014-2 (2001), EN 61000-3-2 (2006)
Signature
14
Nilfisk-Advance A/S, Industrivej 1, DK - 9560 Hadsund, tel.: (+45) 7218 2100