Professional Documents
Culture Documents
Calculating Soil Bearing Pressure Under Mobile Crane Outrigger PDF
Calculating Soil Bearing Pressure Under Mobile Crane Outrigger PDF
The process of determining the soil bearing pressure under mobile crane outriggers is relatively
simple process of taking the maximum outrigger load and dividing it by the effective area of the bearing
pad/mat under the outrigger. The following formula may be used to calculate bearing pressure under a
mobile crane outrigger.
=
×
where,
Q = bearing pressure
While determining the soil bearing pressure is relatively simple, determining the maximum
outrigger load is not so simple. Calculating the maximum outrigger load is complicated and over the skills
of the riggers, supervisor etc. Most crane manufactures have charts that can be used to determine the
maximum outrigger load for a given crane configuration. However, these charts are not typically available
as most crane manufactures do not like to disseminate this information.
Determining the outrigger loads without manufactures charts is a complicated process of crane
data collection and mathematical calculations. The following crane data is required to determine
outrigger loading of which not all is readily available from the manufactures published technical data on
the crane.
W c = Carrier weight
W b = Boom weigh and its center of gravity from boom king pin
Page 1 of 4
Calculating Soil Bearing Pressure under Mobile Crane Outriggers
Lb =Boom and jib center of gravity horizontal distance from boom king pin
θ = Boom angle
L = Lifted Load
= + cos
= + −
= + +
= − −
=
= ±
moment portion is added for rear outrigger
4 2" and subtracted for front outrigger
+
#
= + + Boom side front outrigger
4 2" 2"
+
# = − + Counterweight side front outrigger
4 2" 2"
+
= + − Boom side rear outrigger
4 2" 2"
+
= − − Counterweight rear front outrigger
4 2" 2"
where,
Mb = Boom moment
Mu = Moment of upperworks
Page 2 of 4
Calculating Soil Bearing Pressure under Mobile Crane Outriggers
Mnr = Moment of all loads about outrigger center of gravity lifting over rear
Mns = Moment of all loads about outrigger center of gravity lifting over side
Moment effect values remain constant for a particular load, operating radius, and boom position
relative to longitudinal axis—only the sign changes.
The same condition exists when the boom is positioned over the corner at an angle from the
longitudinal axis of crane, operating over the rear. In this case, the value of Mnr and Mns will be calculated:
= cos ∝ − −
= sin ∝
α is the slew angle of boom from rear of the crane. Mnr is portion of moment due to effect load lift
over the rear, and Mns is portion of moment over the side. The individual outrigger pressure is in
combination of vertical load and moment.
1
#
= + ) − *
4 2 " "
Boom side front outrigger
1
# = − ) + * Counterweight side front outrigger
4 2 " "
1
= + ) + *
4 2 " "
Boom side rear outrigger
1
= − ) − * Counterweight rear front outrigger
4 2 " "
It is not unusual for the calculated value for one of the outriggers to be negative. This means that the
crane lifts free of an outrigger beam or even lifts a float. In this case, it is considered that the reaction at
that outrigger is 0. When two outrigger floats lift or two reactions have negative calculated values, the
crane is in the process of tipping. The sum of all outrigger reactions must be equal to total weight of
crane + load + boom. In addition, the sum of all moments about crane longitudinal centerline and about
transverse line must be 0.
A reasonable approximation of the maximum outrigger load can be made using the information in
the Australian Mobile Crane Code of Practice (2006). Section 10.2.6 Calculating pressure applied by
outriggers states the following:
If a crane is designed in accordance with AS 1418.5: Cranes, hoists and winches – Mobile
cranes, the crane will overturn within the stability part of the load chart when the maximum safe
working load (SWL) is multiplied by a factor of 1.33. In reality, a crane will not approach this
Page 3 of 4
Calculating Soil Bearing Pressure under Mobile Crane Outriggers
condition, provided the operator does not overload the crane. However, a reasonable
approximation for maximum ground pressure applied by the outriggers is detailed below.
2
Pressure (tonnes per m ) applied by outrigger feet:
0.65 × C; + L
=
area
where,
W L – Total Weight of Lifted Load (including block, lines, rigging, load, etc)
A good source for further information on soil bearing pressure under crane outriggers and crane
pad/mat design is a paper titled “Effective Bearing Length of Crane Mats” by David Duerr, P.E. that was
presented at the 2010 Crane & Rigging Conference in Houston, Texas.
References:
1. Effective Bearing Length of Crane Mats” by David Duerr, P.E., presented at the 2010 Crane &
Rigging Conference in Houston, Texas
3. Australian Mobile Crane Code of Practice 2006, Queensland Government, Department of Justice
and Attorney-General.
Page 4 of 4