Professional Documents
Culture Documents
This standard has been approved for use by agencies of the Department of Defense.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
D 1183
5.4 Substitute Ocean Water, with the following composition 9. Calculations
(Note 3): 9.1 The average strength value determined in accordance
Compound Concentration, g/L with the designated method of test is used to calculate the
NaCl 24.53
MgCl2·6H2O 11.11 change in strength, as follows:
Na2SO4 4.09 R 5 @~Y 2 X!/X#3 100 (1)
CaCl2 1.16
KCl 0.695
NaHCO3 0.201
where:
KBr 0.101 R = percent change in strength as a result of exposure to the
H3BO3 0.027 test conditions,
SrCl2·6H2O 0.042
X = initial strength, and
NaF 0.003
Y = strength after exposure to the test conditions.
NOTE 3—These requirements for composition of substitute ocean water The sign of the result will indicate whether there is a gain
are identical with those prescribed for substitute ocean water, without
( + ) or loss (−) in strength.
heavy metals, in Specification D 1141.
9.2 Specimens or panels that delaminate during the tests
5.5 Other Apparatus as required by the ASTM method for have a change in strength of − 100 %. Specimens that delami-
the particular strength property used to evaluate the extent of nate during the tests before the strength test can be made have
degradation. a strength of 0, included in calculating the average strength and
standard deviation.
6. Test Specimens
6.1 The number and type of test specimens meet the 10. Report
requirements of the particular strength method used to evaluate 10.1 Report the following information:
the extent of degradation. Test panels may also be exposed to 10.1.1 Title and designation of strength method used,
those conditions, after which the specified test specimens shall
10.1.2 Information required in particular strength method
be cut from the panels. One set of specimens shall be tested
used,
without exposure to the accelerated service tests, and another
10.1.3 Test procedure,
set after exposure.
10.1.4 Number of cycles,
7. Conditioning 10.1.5 Whether test specimens or panels were used,
10.1.6 Percentage change in strength,
7.1 Condition all specimens for 7 days at a relative humidity
10.1.7 Changes in appearance of test specimens or panels,
of 50 6 2 % at 23 6 1°C.
10.1.8 Number of specimens which delaminated and per-
8. Procedure cent delamination during the test before the strength tests were
made,
8.1 Subject specimens or panels to the number of cycles of
10.1.9 Standard deviation, and
one of the test procedures listed in Table 1, as specified in the
10.1.10 Average wood failure, in percent, for bonded wood
material specifications.
specimens.
8.2 Place the specimens or panels in the containers so that
free access of the controlled atmosphere is obtained for at least
11. Precision and Bias
75 % of the total area of each test specimen or panel.
8.3 After completion of the exposure of the test specimens 11.1 Precision and bias does not exist for these test methods
or panels to one of the procedures in Table 1, condition the test because resources necessary for round-robin testing have not
specimens or panels for 7 days at a relative humidity of 50 % been forthcoming.
at 236 1°C (73.46 2°F) and then test them immediately for the
specified strength properties, unless otherwise stated in the 12. Keywords
material specifications. 12.1 adhesives; humidity; laboratory aging; temperature
2
D 1183
3
D 1183
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org).