Professional Documents
Culture Documents
TECHNICAL SPECIFICATIONS -
LOW VOLTAGE INDUCTION MOTORS
Rev 00 Page 2 of 2
INDEX SHEET
The document Cover Sheet indicates revisions made in this document along with the purpose of
issue of the revised document. The details of revisions made in the enclosures of this document
are listed in the table of Contents below and the enclosures listed therein are an integral part of
this document.
CONTENTS
Part Doc. Description No. Of Rev. Revised Clauses
Size Pages No.
017 018
019 ATEX 1999/92/EC, 020
021 ISO-1940-1, NEMA-MG-1, IEEE-112 022
023 024
025 026
027 028
029 Stator Winding
a. Winding Connection : Star or Delta <100L, Delta >100L
b. Insulation : Class-F, temperature rise limited to class B
c. Temperature Rise (by resistance method)
i) For Industrial/ Ex-'d'/ Ex-'n' motors : 70°C over an ambient of 50°C
ii) For Ex-'e' motors : 70°C over an ambient of 50°C for single layer
and 60°C for other insulated windings
030 Winding Treatment (non-VFD) : Vacuum pressure impregnated for frame 315 & above
otherwise varnished-baked
031 Tropical Protection : Antifungus, Moisture resistant (Epoxy gel coating on winding overhang)
032 Temperature rise of bearings (skin temperature) & lubricant
i) At full load : To suit the withstand temperature of lubricant but
final temperature not exceeding 100 Deg C
ii) At no-load : 15 Deg C above ambient of 50° C
iii) Lubricant : UNIREXN-3 (Suitable for operation at temperature of 130 Deg C minimum)
033 Cooling Designation as per IS 6362 : IC411
CHARACTERISTICS
034 Overvoltage withstand capacity, for Changeover of Power Supply : 150 % of rated voltage
035 Minimum Permissible Voltage for -
a. Starting at full load : 80 % of rated voltage
b. 5 minute running without overheating : 75 % of rated voltage (Occassionally)
036 Max. starting current : 9.2 times rated full load current (including tolerance)
037 Maximum slip at full load : % *
038 Shaft voltage : Max. 200 mV *
039 Min. starting torque : As per IS 12615
040 Noise Level : 85 dB at 1 meter
041 Class of Vibration severity : Grade 'A' of IEC 60034-14, freely placed on test bench without bolting
042 Balancing of rotor :
a. Upto 160KW : To meet vibration severity requirement *
b. Above 160 kW :
i) Speed 3000 rpm & above and turbo compressor motor : To meet vibration severity requirement *
ii) Other motors : To meet vibration severity requirement *
We reserve all the rights relating to this technical document © ...2015...ThyssenKrupp Industrial Solutions (India) Private Limited QAD No.PIN-LES–ELT-1020, R0
056 Winding Leads & Terminals : All 6 leads broughtout for frame > 100L
057 Insulators : Non Hygroscopic, Non-Flammable
058 End connection : Studs & lugs (crimped or brazed)
059 Separate terminal boxes for space heater & thermistor terminals shall be provided
060 Cable Glands : By purchaser, Type : Nickel plated Brass, Double comp., ISO metric, 1.5 mm thread pitch
Terminal blocks shall be suitable for Purchaser's cable sizes which shall be specified after order.
061 Primer : 2 coats of epoxy based primer, spray painted
062 Final Paint : 2 coats of epoxy based finish paint (acid alkali proof)
063 Final paint shade
PAINTING
torque application
078 Design Basis : Stator critical
079 Combined testing of motor & VFD at motor works : For Ex 'e', Ex 'n' & Ex 'd' motors (See Note-3)
'tE' for increased safety motor Class for energy efficient motor
Certificate no., temperature class & Gas group for Hazardous area application if applicable
Separate nameplate for motor tag no. & service Direction of Rotation
SUITABILITY FOR
GD2 OF MOTOR
DESIGNATION
GD2 OF LOAD
Speed Range
VFD YES/NO
METHOD OF
METHOD OF
FRAME SIZE
LUBRICANT
KW RATING
MOUNTING
COUPLING
STARTING
REMARKS
Time 'tE'
DUTY,
kg-m2
kg-m2
COUPLED
(sec)
PERM VOLT.
RPM
(#)
AT RATED
AT MAX.
PL.OUT
(Secs.)
(Secs.)
START
START
kgf-m
%FLC
VOLT.
3/4FL
3/4FL
%FLT
%FLT
Amps
Amps
NDE
DE
NL
FL
FL
FL
FL
%
Vrated
(Sec)
(Sec)
Vmin
NOTE: 1. ALL THE ABOVE DATA TO BE FURNISHED BY VENDOR.
2. DATA FURNISHED SHALL BE APPLICABLE FOR ANY TYPE OF MOTOR MOUNTING.(i.e B3 / V1 etc.)
3. VENDOR SHALL FURNISH COOLING TIME CONSTANT AND HEATING TIME CONSTANT FOR MOTORS RATED ABOVE 110 KW
Pg.1 of 1
Plant Client Contract Code Document ID Contract No.
NaOH GRASIM VILAYAT-NaOH
0200-ELT-00-EC-0015 66-0200
EXPANSION VILAYAT EXPN
1. Offer shall be submitted in two parts viz. Technical part and Price part.
b. Copy of “Design Data Sheet” of this specification duly filled in clearly and legibly in the
assigned space against items marked thus '', along with all documents requested with
the offer.
c. Copy of “Scope of Supply & Schedule of Prices” of this specification marked ‘quoted’
against each item, to confirm that the vendor is making an offer as per break up requested
therein.
d. “Inspection Test Plan” of this specification with acceptance of all clauses to be indicated
by letter 'A’ and duly signed.
f. Filled up “Compliance Declaration” of this specification with seal of the company and
initial of the authorized person.
a. Copy of “Scope of Supply & Schedule of Prices” of this specification with unit rate of
each item and total price of each section, with total price of the tender, including supplies
and various services as specified or as recommended by the vendor.
b. Covering letter enclosing above price part and deviation on commercial terms if any.
4. Both the parts of offer shall be submitted in separate sealed envelope indicating details of
offer such as Technical or Price part, enquiry no. and date of submission.
5. Offer will be evaluated based on above documents only and any other document enclosed
with the offer shall not be considered for evaluation of offer.
PIN-LES–ELT-1020, Rev.0, 12-2015
Plant Client Contract Code Document ID Contract No.
NaOH GRASIM VILAYAT-NaOH
0200-ELT-00-EC-0015 66-0200
EXPANSION VILAYAT EXPN
i. DE Bearing 1 no.
ii. NDE Bearing 1 no.
Price break-up to be furnished
iii. External fan 1 no. separately.
iv. End shield of DE 1 no.
v. End shield of NDE 1 no.
vi. Terminal box cover 1 no.
vii. Terminal block 1 no.
TESTING & INSPECTION
3.
Tests as specified Part-IV of this
specification shall be performed in
presence of purchaser’s representative, if
so desired by the purchaser.
TOTAL PRICE OF THIS TENDER FOR ITEM NOS. 1 AND 3 ABOVE Rs.
PIN-LES–ELT-1020, Rev.0, 12-2015
We reserve all the rights relating to this technical document © ...2015...ThyssenKrupp Industrial Solutions (India) Private Limited QAD No.PIN-LES–ELT-1020, R0
2 B3 S1 DOL DD TEFC UR
0.75
4 B3 S1 DOL DD TEFC UR
2 B3 S1 DOL DD TEFC UR
1.1
4 B3 S1 DOL DD TEFC UR
2 V1 S1 DOL DD TEFC UR
1.1
4 V1 S1 DOL DD TEFC UR
2 B3 S1 DOL DD TEFC UR
1.5
4 B3 S1 DOL DD TEFC UR
2 V1 S1 DOL DD TEFC UR
1.5
4 V1 S1 DOL GD TEFC 1
2 B3 S1 DOL DD TEFC UR
2.2
4 B3 S1 DOL DD TEFC UR
2 V1 S1 DOL DD TEFC UR
2.2
4 V1 S1 DOL GD TEFC 1
2 B3 S1 DOL DD TEFC UR
6 B3 S1 DOL DD TEFC UR
2 V1 S1 DOL DD TEFC UR
3.7
4 V1 S1 DOL DD TEFC UR
2 B3 S1 DOL DD TEFC 2
6 B3 S1 DOL DD TEFC 1
2 V1 S1 DOL DD Industrial UR
5.5
4 V1 S1 DOL DD Industrial UR
2 V1 S1 DOL DD Industrial UR
7.5
4 V1 S1 DOL DD Industrial UR
2 B3 S1 DOL DD Industrial 3
6 B3 S1 DOL DD Industrial UR
2 B3 S1 DOL DD Industrial UR
9.3
4 B3 S1 DOL DD Industrial 1
2 V1 S1 DOL DD Industrial UR
9.3
4 V1 S1 DOL DD Industrial UR
2 B3 S1 DOL DD Industrial 2
11
4 B3 S1 DOL DD Industrial UR
2 V1 S1 DOL DD Industrial UR
11
4 V1 S1 DOL DD Industrial UR
2 V1 S1 DOL DD Industrial UR
15
4 V1 S1 DOL DD Industrial UR
2 B3 S1 DOL DD Industrial 4
15
4 B3 S1 DOL GD / DD Industrial UR
2 B3 S1 DOL DD Industrial UR
18.5
4 B3 S1 DOL GD / DD Industrial UR
Pg. 1 of 2
We reserve all the rights relating to this technical document © ...2015...ThyssenKrupp Industrial Solutions (India) Private Limited QAD No.PIN-LES–ELT-1020, R0
2 B3 S1 DOL DD Industrial 2
22
4 B3 S1 DOL DD Industrial UR
2 B3 S1 DOL DD Industrial UR
30
4 B3 S1 DOL DD Industrial UR
2 B3 S1 DOL DD Industrial 2
37
4 B3 S1 DOL DD Industrial UR
2 B3 S1 DOL DD Industrial UR
45
4 B3 S1 DOL DD Industrial UR
2 B3 S1 DOL BD Industrial UR
75
4 B3 S1 DOL BD Industrial UR
Pg. 2 of 2
We reserve all the rights relating to this technical document © ...2015...ThyssenKrupp Industrial Solutions (India) Private Limited QAD No.PIN-LES–ELT-1020, R0
LOW VOLTAGE INDUCTION MOTORS Code VILAYAT-NaOH EXPN
ANNEXURE - II TO PART - IIIB Contract no. 66-0200
Doc. 0200-ELT-00-EC-0015
Rev. 0 Page 1 of 1
DIRECTION OF ROTATION
SR. MOUN FRAME METHOD OF VIEWED FROM DE MANUFACTURING
TAG SERVICE KW POLES DUTY ENCLOSURE TYPE EFFICIENCY CLASS POWER CABLE SIZE REMARKS
NO. TING SIZE STARTING (CLOCKWISE/ ANTI- STATUS
CLOCKWISE)
C Additional Tests
D Certificates
Notes:
1) R = Review of test certificates; W = Witness, P = Perform. (On project equipment), PPROTO= Perform (on prototype)
2) To be carried out for motors for which temperature rise test has not been performed.
Plant Client Contract Code Document ID Contract No.
NaOH GRASIM VILAYAT-NaOH
0200-ELT-00-EC-0015 66-0200
EXPANSION VILAYAT EXPN
Compliance Declaration
Please note that vendor shall indicate his replies to the following points without which the offer shall
be liable for rejection.
Deviations if any from this specification shall be listed in the enclosed format (List of Deviations)
indicating the applicable specification clause. The vendor will be made liable for full
compliance with the specification requirements, if deviations are not listed in “List of
Deviations” as it will be deemed as “No deviation”.
(Signature of Vendor)
Name:
Designation :
Date : (Company Seal)
Plant Client Contract Code Document ID Contract No.
NaOH GRASIM VILAYAT-NaOH
0200-ELT-00-EC-0015 66-0200
EXPANSION VILAYAT EXPN
LIST OF DEVIATIONS
Doc. No:
(Signature of Vendor)
Name:
Designation :
Date : (Company Seal)