Professional Documents
Culture Documents
Philips 29pt9457 1-1-55 Chassis Sk5 0l CA SM
Philips 29pt9457 1-1-55 Chassis Sk5 0l CA SM
SK5.0L
CA
H_17220_000.eps
210607
Contents Page
1. Technical Specifications, Connections, and Chassis
Overview 2
2. Safety Instructions, Warnings, and Notes 4
3. Directions for Use 5
4. Mechanical Instructions 6
5. Service Modes, Error Codes, and Fault Finding 8
6. Block Diagrams, Test Point Overview, and
Waveforms
Block Diagram Chassis 9
Schematic Overview Chassis 10
7. Circuit Diagrams and PWB Layouts
Mono Carrier: Power Supply (A1) 11 19-20
Mono Carrier: Line Deflection (A2) 12 19-20
Mono Carrier: Frame Deflection (A3) 13 19-20
Mono Carrier: Tuner IF (A4) 14 19-20
Mono Carrier: AV Switch (A5) 15 19-20
Mono Carrier: Tone Control (Optional) (A6) 16 19-20
Mono Carrier: Audio Amplifier (A7) 17 19-20
Mono Carrier: CPU & Decoder (A8) 18 19-20
CRT Board (B) 21 19-20
Keyboard Control Panel (D) 22 23
Mains Filter Panel (E) 24 24
Side A/V Panel (G) 25 25
8. Alignments 29
9. Circuit Descriptions, Abbreviation List, and IC Data
Sheets 34
Abbreviation List 35
IC Data Sheets 36
10. Spare Parts List 51
11. Revision List 54
©
Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.
Published by JY 0768 BU CD Customer Service Printed in the Netherlands Subject to modification EN 3122 785 17460
EN 2 1. SK5.0l CA Technical Specifications, Connections, and Chassis Overview
1.1.1 Vision
: UHF 280607
Aerial - In
Sound systems : Stereo, SAP
- - F-connector Coax, 75 ohm D
Maximum power (WRMS) : 2x5
B CRT BOARD
E MAINS FILTER
D CONTROL PANEL
A1 POWER SUPPLY
A2 LINE DEFLECTION
A3 FRAME DEFLECTION
A4 TUNER IF
MONO CARRIER A A5 AV SWITCH
A6 TONE CONTROL
BTSC PANEL M A7 AUDIO AMPLIFIER
A8 CPU & DECODER
SIDE AV PANEL G
H_17220_024.eps
280607
Safety regulations require the following during a repair: • In order to prevent damage to ICs and transistors, avoid all
• Connect the set to the Mains/AC Power via an isolation high voltage flashovers. In order to prevent damage to the
transformer (> 800 VA). picture tube, use the method shown in figure “Discharge
• Replace safety components, indicated by the symbol h , picture tube”, to discharge the picture tube. Use a high
only by components identical to the original ones. Any voltage probe and a multi-meter (position VDC). Discharge
other component substitution (other than original type) may until the meter reading is 0 V (after approx. 30 s).
increase risk of fire or electrical shock hazard.
• Wear safety goggles when you replace the CRT.
2.4.2 Schematic Notes avoid mixed regimes. If this cannot be avoided, carefully
clear the solder-joint from old tin and re-solder with new tin.
• All resistor values are in ohms, and the value multiplier is
often used to indicate the decimal point location (e.g. 2K2 2.4.4 Alternative BOM identification
indicates 2.2 kohm).
• Resistor values with no multiplier may be indicated with In September 2003, Philips CE introduced a change in the way
either an "E" or an "R" (e.g. 220E or 220R indicates the serial number (or production number, see Figure 2-2) is
220 ohm). composed. From this date on, the third digit in the serial
• All capacitor values are given in micro-farads (μ= x10-6), number (example: AG2B0335000001) indicates the number of
nano-farads (n= x10-9), or pico-farads (p= x10-12). the alternative BOM (Bill of Materials used for producing the
• Capacitor values may also use the value multiplier as the specific model of TV set). It is possible that the same TV model
decimal point indication (e.g. 2p2 indicates 2.2 pF). on the market is produced with e.g. two different types of
• An "asterisk" (*) indicates component usage varies. Refer displays, coming from two different O.E.M.s.
to the diversity tables for the correct values. By looking at the third digit of the serial number, the service
• The correct component values are listed in the Spare Parts technician can see if there is more than one type of B.O.M.
List. Therefore, always check this list when there is any used in the production of the TV set he is working with. He can
doubt. then consult the At Your Service Web site, where he can type
in the Commercial Type Version Number of the TV set (e.g.
2.4.3 Lead-free Soldering 28PW9515/12), after which a screen will appear that gives
information about the number of alternative B.O.M.s used.
Due to lead-free technology some rules have to be respected If the third digit of the serial number contains the number 1
by the workshop during a repair: (example: AG1B033500001), then there is only one B.O.M.
• Use only lead-free soldering tin Philips SAC305 with order version of the TV set on the market. If the third digit is a 2
code 0622 149 00106. If lead-free solder paste is required, (example: AG2B0335000001), then there are two different
please contact the manufacturer of your soldering B.O.M.s. Information about this is important for ordering the
equipment. In general, use of solder paste within correct spare parts!
workshops should be avoided because paste is not easy to For the third digit, the numbers 1...9 and the characters A...Z
store and to handle. can be used, so in total: 9 plus 26 = 35 different B.O.M.s can
• Use only adequate solder tools applicable for lead-free be indicated by the third digit of the serial number.
soldering tin. The solder tool must be able:
– To reach a solder-tip temperature of at least 400°C. 2.4.5 Practical Service Precautions
– To stabilize the adjusted temperature at the solder-tip.
– To exchange solder-tips for different applications. • It makes sense to avoid exposure to electrical shock.
• Adjust your solder tool so that a temperature of around While some sources are expected to have a possible
360°C - 380°C is reached and stabilized at the solder joint. dangerous impact, others of quite high potential are of
Heating time of the solder-joint should not exceed ~ 4 sec. limited current and are sometimes held in less regard.
Avoid temperatures above 400°C, otherwise wear-out of • Always respect voltages. While some may not be
tips will increase drastically and flux-fluid will be destroyed. dangerous in themselves, they can cause unexpected
To avoid wear-out of tips, switch “off” unused equipment or reactions that are best avoided. Before reaching into a
reduce heat. powered TV set, it is best to test the high voltage insulation.
• Mix of lead-free soldering tin/parts with leaded soldering It is easy to do, and is a good service precaution.
tin/parts is possible but PHILIPS recommends strongly to
4. Mechanical Instructions
Index of this chapter: 4.1.1 Rear Cover Removal
4.1 Set Disassembly
4.2 Assembly / Board Removal Warning: disconnect the mains power cord before you remove
4.3 Set Re-assembly the rear cover.
Note: Figures below can deviate slightly from the actual 1. Remove all the fixation screws of the rear cover.
situation, due to the different set executions. 2. Now, pull the rear cover backwards and remove it.
H_17220_036.eps
280607
1. From the mono carrier disconnect the main power and the
keyboard circuit cables. Release the main power cord and
the keyboard circuit cable from it’s strain reliefs.
2. Then, remove the six fixation screws [1] of the power
switch and control panel and remove the board.
H_17230_027.eps
290607
H_17220_023.eps
210607
1. Disconnect the side panel cable from the mono carrier and
remove the cable from it’s strain reliefs.
2. Then, remove the four fixation screws [1] and remove the
board.
5.1 Test Points 5.4.7 Picture with Horizontal Bright Line and Sound
See chapter 6 "Block Diagrams, Testpoint Overviews, and Check both supply voltages of vertical IC301 and relevant
Waveforms". circuitry on correctness. Also check the vertical synchronizing
signal from IC201.
Perform measurements under the following conditions:
• Service Default Mode. 5.4.8 Remote Control Malfunction
• Video: colour bar signal.
• Audio: 3 kHz left, 1 kHz right. Check the voltage on pin 64 of IC201. The normal value should
be 5.15 V. If this is correct check front control panels soldering
connections. If can't be solved, check the remote control,
5.2 Service Modes crystal or transmitting diode of the remote control are in good
condition.
This chassis does not contain a specific Service Mode. Service
and Alignment of the TV set can be done via the Factory Mode 5.4.9 No Sound
by the service technician, see further down in this manual.
5.4.1 Power on Failure Check the sound system after searching the channel which
should set at NTSC or AUTO. If still has problem, check
Check whether the power supply is working properly and accompany board circuit on chassis good or not.
whether the values of voltages normal. If those are correct,
check line transistor and transformer are working properly or
check fore or back line for defects.
9 LQ 9 LQ
VLGH 9
5 *% A6 A7
9LGHR6: +() /
$037'$
/ 63/
721( &21752/
7'$
$9 LQ & LQ
5
5 635
A8 1,&$07'$
,) A5
6$:
781(5 ,) $03
,) M 0767'$
%
%
9'<
9 )25 %
9D R XW
32:(5 6833/<
9 )25 +GULYH 9$03 7'$$-
9E RXW
&
A3 +'<
9 )25 0$,1
6:
:$
99
A1 +'5,9(
6/,0 3$57
$
A2 $
'(* &2,/
H_17460_008.eps
280907
Block Diagrams, Test Point Overview, and Waveforms SK5.0A CA 6. EN 10
1
R515 220
2
15K
D504
M001 H501 Q506 BA158
BF420
RD5 RD4 RD3 RD2 RR1 3 2 1 R510
U101 GND Q504
BT +33V
22
BM +5V
10K 18K 100 2K7 100 R
IFGND
C4544
AGC
G
SDA
SAS
SCL
45.75MHz
NC
NC
NC
CRT
IF
L109
B Q505
+8V_VCC MENU BL
1 CR1
10uF/16V R511 R513 R512
BF421
R R517
10
11
100uH 2K2 270 22 R514 2K7 KR
C103 C164 C163 1
100nF 220uF +5V_VCC LED RD1 270 R527 KG
VOL+ VOL- PRO+ PRO- C502
NG 0.82uH SW004 SW003 SW002 SW001 D503 330PF 2K7
R103
R106 L101 R107
820
LED 100 1N4148 KB
C111 NG
5
C112
C110 R113 R112 R111 C405 5.6K R120 R508
C109 C105 2K7
E
10uF NC 47K
100pF 100 100 100pF 47uF C101 IF C118 1K E
SCL
PTC
SDA
Vdd
0.01u ZD102 C117 ZD501 C508
10nF R526
Q101 5V1 IC102 8V2
1
100uF R525 220
C2717 100nF C108 C107 R145 R130 R131 R132 1000PF
2
24C08 15K
5
3
1
2
4
R109 +5V 100pF 100pF 22K 3.3K 3.3K 3.3K R121 Q106 D506
GND
KEY
LED
IR
R102
5V
C1815 Q509
Vss
WP
n.c.
BA158
A2
10K 1K2 10K BF420
R105
ZD101 R108 R521 Q507
R110 5V1 22
1
33 22
R149 R148
4
180 +5V_VCC C4544
3.3K 3.3K
IC201
R140
KEY Q508
BF421
G
R101 STANDBY 1 64 R520 R523 R522
STANDBY IRin 2K2 270 22 R524
1
AGC 0.1uF 10uH R725 10K R506 220
2
VOL 7 58 15K C507
2
10uH
C148 Q503 NC
+
8 57 R725 75 BA158
R122 BAND OscGnd
TDA9363 for AP
220K
8V2 9 56 33pF R501 Q501
SCREEN
10K
EHT
Vss C/P VddC
FOCUS
22K 22
VO Q703 MUTE R724 R725 R425 C4544
C720 10
MUTE VpE
55 C149 33K R414
C1815 10nF 27K ZD104 ZD106 ZD107 ZD108
11 54 10K Q502
8V2 VIDEO OUT
R717 C710 10uF
C129
PAL/NTSC VddA
R144 100
39K 8V2 8V2 8V2 8V2 1
GND
R502 R503 R504
BF421 B H502
HEATER
+180V
GND
12 53
+
VssA B OUT B 2K2 270 22 R505
68 470uF R711 R712 10uF/16V C127 220nF 13 52 R143 100 2 1
V L205
SECPLL G OUT G 270
75 22K +8V
14
Vp2 R OUT
51 R142 100 3
R
CN102 D501
C501
330PF
ZD714 R721 220nF 1N4148
10uH C128 10nF C130 15 50 R141 10K 4
8V2 75 DECDIG BLANKING BL
C132 4n7 C131 2200p 16 49 5 BCL
CVBS OUT PH2LF BCL IN
C133 17 48 C727 0.1uF U / B in
Y IC761 PH1LF B / U IN
+
C120 C119 1uF/50V R138 18 47 C726 0.1uF Y / G in
ZD705 R722 HEF4052 + GND3 G / Y IN
+12V_VCC 0.1U/63V 10uF/16V 18K C725 0.1uF V / R in
8V2 100 1
Vdd
16 19
DECBG R / V IN
46
+
SAW101 IREF CVBSINT 47uF 4RM 10W
L702 REAR AV 470uF Lout
39K
3
C717
Q1976M
C135 26 39 8V 8RM 6W
33uH
L706 6 11 0.1U/63V
VSC Vp1
R125
D762 1 1
15uH
E AGC 27 38 R413 1N4148
R765
SW2
RO L701 10uF
TUNER AGC IFVO/SVO
R147 C144 R137 D761
33uH 7
Vee
10 A1 28
AUDEEM/SIF1 PLL IF
37 220 100K
MUTE Q761
1K 2 2
C701 R701 ZD701 0.1U/63V Rout SPR
ZD703 8V2 29 36 390 X-RAY 1K 1N4148
C1815 C768 SW2
4RM 10W
8V2 1000pF 47K 8 9 A2 DECSDEM/SIF2 EHTO R771 470uF
8RM 6W
Vss 10K
C136 30 35 R412
GND2 AUDEXT/QSSO
C137
VIDEO SWITCH 33PF 10UF
C138 R139 31 34 27K R764
SNDPLL/SIFAGC FBISO PWM R763 6.2K
4.7nF 3.9K 32 33
AVL/REFO H. OUT 15K
C760 C761
C139 C140 10uF/16V
1uF
V in 330pF 4.7uF AFC
50V
Y H-out C750 R770 1K
Y in
L R OUT 1uF
U in
P701 S-VHS CVBS/Y IN L OUT C749 R769 1K C765
U 1uF
P702 C C785
C IN C766
+8V 4700PF 4700PF
YUV
R
10uF
V
Y ZD707
R779 8V2 AUDIO R out +20V_VCC
AUDIO L out
75
C708 C707
10uF 10uF Q107
TV CVBS OUT
IC851 C1815
Q702 Q701 TDA9850 L103
R852
C777
1
VEO Cs 32
C862
1uF
R127 12uH R728 TV CVBS IN
R706 C1815 R705 C1815 C863 R853 8K2
2 31 C861 R742
VEI Cw 1K 13K
V out V IN 1K8 1K8 47nF 150 C864
1uF
R126 100 XT155 R729
10uF 3 30 C860 ZD715
Cnr Cts 10uF 180 XT-4.5 C740
C772
R710 R708 R709 R707 10uF
4 29 C809 GND C? 1K2 8V2
P701 L002
C865
0.1uF
Cm Ctw
10uF
220PF/50V C752
C753 C754 100uF/16V
16
15
14
13
12
11
10
R778 100
R777 R780
1
2.2uF
100
8V2 ZD709 ZD711 OUT L OUT R SCL R856 100 9
SCL Vref 24 C868
47K 47K
TONE CONTROL
8V2 8V2 100uF
SCL
LOUT_R
LIN_R
N.C.
MOUT_R
SCOUT_R
MIN_R
V_P
C_SMO
C_TR
C_BR2
C_BR1
GND
MIN_L
P1
SCIN_L
SIDE AV IN C002 R854 10 23
C 1000p In Out Vcc SAP C
Gnd
+12V 10 11
COMP Csde 22
C858
C003 TV L IC852 15nF
1000p L7809
C851 C877
C878 C876 C875
0.1uF C869 12
Vcap OUTR 21 C871 IC740
1uF 10uF 1uF
100pF 100pF 100uF 13 20 C873
Cp1 Cr 2.2uF TDA9859
C852 14 19 C877
IC762 R857 Cp2 Css 4.7uF
47K R851 0.47uF
15 18 C856
HEF4052
SCOUT_L
Cph Cmo
MOUT_L
LOUT_L
SCIN_R
4.7uF
+12V_VCC 2K2
AIN_R
C_BL2
C_BL1
AIN_L
L
C_PS2
C_PS1
LIN_L
1 16 16 17
C_TL
MAD
C879 C853 Cadj CER
SDA
Vdd
N.C.
QSS Q851
P2
4.7uF C854
C1815 C855 X851
SIDE L 2 15 SIDE R 1uF 0.22uF 10uF 503KHz
R745 R746
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
0 47K 47K R858 R860
C778 3 14 C742 47K 1K SDA
1 REAR R AUDIO L
2
V IN C775 3
0 AUDIO L
1
BTSC out L
10uF 4 13 R 10uF
BTSC out R
2 AUDIO R
C770 10uF 3 C741
P701 L IN
L704
15uH
C783
10uF
REAR L
5
6
12
11
C771 10uF
AUDIO R
TV R
BTSC BOARD C748
5n6
C746
0.15uF
C745
68nF
C744
15nF
C743
15nF
E
1000p C773
L703
15uH 7 10
10uF
A1
FOR LATAM R743
R IN
TV L
TV R
Vee 13K
10uF
R776 R775 R719 ZD712 ZD708 ZD710 8 9 A2
Vss
47K 47K 100 8V2 8V2 8V2
REAR AV IN
C776
AUDIO SWITCH R744 R747
47K 47K CN301 CN401
1000p
V - DEF H-DEF CONNECT TO H502 FOR RF Tube
IC301 8V
! TDA4865AJ R462 1 OHM ( 2W )
1
VP4 -17.5V
R417 4.7K ( 1/6W)
VP1 +17.5V
R413
5
Vp3 pump
6 100K
! R419 390K (1/6W)
V out
VP3-
INN
INP
ZD402 D404
R421 X-ray
X-ray
C463 0.36uF (400V)
18V
180
1N4148
C438 1500pF (2000V)
1
100V R412
R461
C456 R422
680 C407
R418
NC
27K C431 6800pF (2000V)
R423
5.6 1/4W
6.2 2W NC C432 6800pF (2000V)
C455 0.1uF/100V
R640 VDRA R460 L440 790uH
100V R453
D627
RL601 0 100
100uF/50V
L430 30uH
R457 35V 270 1W
C640 Q625 VDRB R452
R423 5.6 (2W)
1N4148 R644 C1815 5.6
100 D452
B C611
RELAY 10K
J408 BA158 C433 18nF (630V) B
AC220V 470PF 220uF C160 C161 1K8
C639 R643 C460 C461 R459 R441 75K (1/6W)
47uF 47K 470P 470P 1nF/50V 1nF 1K8 ! R440 6.8 (2W)
C612 50V +16.2V
AC220V 470PF C459 D450
T402 C435 0 OHM
0.1uF/100V R463 BYW36
R450
4 HV TO CRT L431 not used
EHT
C603A C603B 220/2W 470pF 0.22 +16.2V
25mH L603 R468 2W -16.2V R451
2W L432 not used
Rs 4700pF 4700pF C624
2 3 +21V_VCC 5.1 R462
0.82
5
-16.2V
C445 R407 R409 AFC C464 not used
D451 0.22 AFC
C603 A B T603 680pF 500V C627 C628
BYW36
2n2F/100V 22K 27K C465 not used
0.22uF R469
1000uF 1000uF 8
PTC601 Rp AC250V
D603
16 1 D623 25V 25v +12V_VCC 5 OHM C452
470pF
HEATER ZD401
CN604 NTC 2200uF/25V C444 8V2
9RM 1
N L D C RU4YX C453 6 39PF/50V
2200uF/25V
N L C603D C603C C607 15 2 <20V> R624
R632 IC104 +8V_VCC AFC
9
CN602 FOR CB In Out
FOR EMC R600 FBP
C600 L602 NTC
4700pF 4700pF 220uF 0.22 2W 1 L7808 Gnd 390 +5V_VCC
PFC 15mH×2 5RM 450V
14 3 D626 +12V R645 3
0.1uF/250V C602 C623 BA158 R638 +3.3V_VCC
680pF 500V
0.22uF/250V C604 C625 C626 C641 22 Q626 FOCUS
R602 13 4<12V> R622 D622 1000uF 1000uF Q624 2200uF R650 C1815 +135V_VCC 2
FOCUS
2
FB
VCC
D
OLP/SS
OCP/BD
FOR SLIM
H_17460_002.eps
240907
1 2 3 4 5
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 11
A1 POWER SUPPLY A1
R640
D RL601 D627 0 D
C640 Q625
1N4148 R644 C1815
RELAY 220uF 10K
C639 R643
47uF 47K
C603A C603B
Rs T601 4700pF 4700pF C624
2 3 +20V_VCC
+20V_VCC
C603 A B T603 680pF 500V C627 C628
0.22uF 1000uF 1000uF
PTC601 Rp AC250V
D603
16 1 D623 25V 25v +12V_VCC
CN604
9RM N L D C RU4YX +12V_VCC
1
N CN602 L C603D C603C C607 15 2<20V>R624
R632 IC104 +8V_VCC
C FOR CB In Out +8V_VCC C
C600
FOR EMC
L602
R600
NTC
4700pF 4700pF 220uF 0.22 2W 1 L7808 Gnd 390 +5V_VCC
+5V_VCC
PFC 15mH×2 5RM 450V
14 3 D626 +12V R638
R645
0.1uF/250V C602 C623 BA158 +3.3V_VCC
+3.3V_VCC
680pF 500V
0.22uF/250V C604 C625 C626 C64122 Q626
R602 R650 C1815
13 4<12V>R622 D622 1000uF 1000uF Q624 2200uF
2
OCP/BD
S/GND
2.2M 1/2W
VCC
FB
D
R631
2 N
BLUE IC622 1K
CN601 F601 R630
1 680 Q623
R608 ZD620 R634
AC90-270V BROWN L 10K C1815 J615
T3.15A
2K2 5V1
STANDBYSTANDBY
AC250V IC601 OPTOISO1
10K
STR-W6556A R610 8.2M
R627 C634 H:WORKING
0.1uF L:STANDBY
IC621 6.2K
Q621 50V
SE120
C610 0.0022uF C1815
A A
H_17220_001.eps
5800-A5P190-00 180607
1 2 3 4 5 6
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 12
8V
1
R413
6 5
D 100K D
! D404
ZD402
R421 X-ray
X-ray
180
18V 1N4148
R422 R418 R412
27K
R423 680 C407 NC
3.9 2W NC
!
T402
R450 HV TO CRT
+V 4
EHT
0.22 +13V
2W
R451
-V 5
-13V
C445 R407 R409 AFC
0.22 AFC
C 2n2F/100V 22K 27K C
8
HEATER ZD401
C444 8V2
6 27PF/50V
AFC
9
FBP
FOCUS
+48V_VCC FOCUS
2
B+
R406 ! 10
1K/1W
+8V_VCC 180V SCREEN R417
SCREEN
D433 R433
C437 C436 BA158 +8V_VCC
0.33
10uF 560pF 5K6
1W
250V 2KV R419 R416
560K 1K
R443
470 R441 R440 R432
270
75K 6.8 2W L430
L440 790uH C406 20uH
Q440 1uF C464
F630 C440 250V 0.18uF
4.7uF C442
0.01uF
! 100V
50V C463 ! 2200PF
A 0.33uF D432 L431 A
R430 160uH
C441
ZD440 15K BA158
0.01uF
8.2V 50V
A3 FRAME DEFLECTION A3
CN301
D IC301 D
! TDA4863AJ
Vp3 pump
VP1 +13V
5
VP4 -13V
6
!
V out
VP3-
INN
INP
7
1
100V
C456
R461
5.6 1/4W
VDRAR460 C455 0.1uF/100V
C VDRA 100V R453 C
100
R457 35V 100uF/50V 270 1W
R452
VDRB 5.6 D452
VDRB 100 J408 BA158
1K8
C460 C461 R459
1nF/50V 1nF 1K8
50V +14V
C459 D450
0.1uF/100VR463 BYW36
R462 +V
2W1 220/2W 470pF
-14V
B +V B
D451
BYW36
470pF
C452
0.1uF 1000uF/25V
0.1uF C453
1000uF/25V
A A
H_17220_003.eps
5800-A5P190-00 180607
1 2 3 4
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 14
A4 TUNER IF A4
E E
D U101 D
BT +33V
BM +5V
IFGND
AGC
SDA
SAS
SCL
38.9MHz
NC
NC
NC
IF
R104 +5V
1 +5V
10
11
1
9
220
C103
10nF R116
R106 L101 R107 10K
C112 C111 C113 R103 1K 1uH 470
C110 R113 R112 R111 C405 5.1K
C109 C105
10uF NC 47K
100pF 100 100 100pF 47uF C101 IF
220uF IF
0.01u
Q101 10nF
C C2717 C106
C
SIF
R109 +5V SIF
R102 10nF
10K 1K5 R105
ZD101 1 R108
22
NTSC
R110 5V1 33
180
L102
C102
+32V_BT
10nF 31.9MHz R117
+8V_VCC
R101 Q102
SYSTEM
75 C1815
C115
10K SYSTEM
SCL SDA 10nF
AGC
AGC
SDA
SCL
B +32V_BT B
+8V_VCC
A A
H_17220_004.eps
5800-A5P190-00 180607
1 2 3 4 5
1 2 3 4
AV SWITCH
A5 A5
GND 21 +8V
C719
D D
VI 20 R713
10uF 20K
VO 19 Q703 C720
VIG18 R715 C1815
8V2 8V2 75 VIDEO OUT C710 10uF
R717
Mono Carrier: AV Switch
VOG 17
BL16 68 470uF R711 R712
V / R 15 75
BG14 ZD714 R721
RGND 13 8V2 75
CVBS OUT
NC12 CVBS OUT
Y / G 11 IC761
ZD705 R722 HEF4052
NC10 SCART1 AV 1 16
+8V_VCC
8V2 75 Vdd +8V_VCC
GGND 9
NO USE J743 only for scart SIDE AV 2 15
OPT8 C780
10K 0 100uF
U/B 7 C716 C779 OUT 3 14
1
10uF 2
0
L in6
C784 3 1
R731 R723 ZD713 R70210uF ZD702 4 13
BGND 5 2
75 8V2 47K 10uF TV
820 3
GND4 8V2 5 12
Circuit Diagrams and PWB Layouts
LO 3 REAR AV
C717
R in 6 11
2 E
10uF
RO 1 7 10 A1
ZD701 Vee A1
ZD703 R701
8V2 8 9 A2
C
P701 21PIN 8V2 47K Vss A2 C
VIDEO SWITCH
BLANK
BLANK
SK5.0A CA
U CVBS/Y IN
P702 C785
C IN C IN
YUV
R
10uF
ZD707
V R779 8V2 AUDIO L out AUDIO R out
75
C708 C707
EN 15
10uF 10uF
Q702 Q701
C777
R706 C1815 R705 C1815
V out V IN 1K8 1K8
10uF
C772
R710 R708 R709 R707
P701
L out L IN
20K 20K 20K 20K
P701 10uF
AV OUT C774 R? R?
ELECTRO1 ELECTRO1
R out R IN
10uF
B R777 R780 R778 ZD706 B
ZD709 ZD711 OUT L OUT R
47K 47K 75 8V2 8V2 8V2
SIDE AV IN
TV L
TV L
GND 21
V in20 IC762
VO 19 HEF4052
L1 16 +8V_VCC
VIG18 Vdd +8V_VCC
VOG SIDE L2
17 15 SIDE R R745 R746
BL16 0 47K 47K
C778 3 1 14 C742
R 15 REAR R AUDIO L
2 AUDIO L
V IN C775 0
BG14 3 1
10uF 4 13 R 10uF
2
RG 13 L C770 10uF 3 C741
5 12 AUDIO R
NO USE NC12 AUDIO R
R P701 L IN REAR L
G 10uF C771 10uF
11 6 11 TV R
E TV R
NC10 C773
10uF
R IN 7 10 A1
Vee A1
10uF
GG 9
OPT8 R776 R775 R719 ZD712 ZD708 ZD710
8 9 A2
Vss A2
B 47K 47K 75 8V2 8V2 8V2
7 REAR AV IN
AUDIO SWITCH R744 R747
LI 6 47K 47K
BG 5
A A
GND
4
LO 3
RI 2
RO 1
P701 21PIN
H_17220_005.eps
5800-A5P190-00 180607
1 2 3 4
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 16
A6 TONE CONTROL A6
+8V_VCC
AUDIO R
AUDIO L
SDA
SCL
A A
+8V_VCC R748
SCL
AUDIO R
AUDIO L
SDA
A7 Audion Amplifier
0
B B
R OUT
L OUT
IC740
C 17 16 C
SDA SCL
18
TDA9859 15
C748
5n6
LOUT_L LOUT_R
19 14
C_TL C_TR
C752
6n8
20 N.C. N.C. 13
0.15uF
C746
D 21 12 D
C_BL2 C_BR2
0.15uF/63V
13K
R743
13K
R742
C753
22 11
C_BL1 C_BR1
68nF
C745
23 LIN_L LIN_R 10
68nF
C754
24 9
MOUT_L MOUT_R
25 MAD GND 8
E E
ZD715
26 7
15nF
C744
8V2
SCOUT_L SCOUT_R
27 6
C_PS2 V_P
28 AIN_L MIN_R 5
29 4
C_PS1 C_SMO
F F
15nF
C743
100uF/16V
30 3
C740
AIN_R MIN_L
31 2
P2 P1
32 1
SCIN_R SCIN_L
G G
H_17220_006.eps
5800-A5P190-00 180607
1 2 3 4 5 6 7 8 9 10
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 17
A7 AUDIO AMPLIFIER A7
D D
+8V_VCC IC760
+8V_VCC
2 4 6 8 TFA9843AJ---10W
D763 IN4148 1 3 5 7 9 TFA 9842AJ---6W
C728 RI RO L in
100uF R768 L out
R766 Q760 100K
A1015 C767 SPL
47K C764 220uF C769
47uF CN760
C 470uF Lout 4RM 10W C
8RM 6W
D762
R765
1 1
1N4148 SW2
R137 D761
MUTE
MUTE Q761
1K 2 2
SPR
C1815 C768 Rout SW2
1K 1N4148
R771 470uF 4RM 10W
10K 8RM 6W
R764
PWM R763 10K
PWM
15K
C760 C761
10uF/16V
1uF
50V
C750 R770 1K
R OUT 1uF
+20V_VCC
+20V_VCC
Pin 15
Pin 18
A6 Tone Control
IC740 TDA9859
A A
H_17220_007.eps
5800-A5P190-00 180607
1 2 3 4
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 18
D D
5
R120
C118 1K
PTC
SCL
Vdd
SDA
ZD102 C117
5V1
100uF/16V IC102 C108 C107 R132 LED
100nF 24C08 R145 R130R131
100pF100pF22K 3.3K 3.3K 3.3K R121 Q106
Vss
n.c.
WP
C1815
A2
10K
R149R148
1
4
3.3K 3.3K
IC201
STANDBY R140
1 64
STANDBY STANDBY IRin IR
SCL R133 100 2 63
100 A2
SCL SCL AV2 A2
SDA R134 100 3 62 A1
SDA SDA AV1 A1
4 61
L105
10uH +3.3V
AV3/TUNING VddP
OPTION only for scart 5 60
OPTION SCART ID RESET C145+ C146 L106
KEY R135 47 6 59
X101 C147 RCA : R724 33K
KEY KEY XTAL OUT 100uF 0.1uF 10uH R725 10K
33pF
SYSTEM
C148 C150
+
8 57 R725 75
R122
TDA9363 for AP
+3.3V 8V2 9 56 33pF 100uF/16V
10K Vss C/P VddC
R724
MUTE 10 55 C149 R725 R425
MUTE MUTE VpE
R115 R119
11 54 10nF 33K R414 10K 27K ZD104 ZD106 ZD107 ZD108
+5V PAL/NTSC VddA 39K 8V2 8V2 8V2 8V2 GND
+5V 4K7 NTSC 3K3 C129 12 53 R144100 1
B
+
VssA B OUT
SYSTEM
10uF/16V C127 220nF 13 52 R143100 2
SYSTEM SECPLL G OUT G
+8V
L205
10uH 14
Vp2 R OUT
51 R142100 3
R
CN102
Q103 C130 220nF
C128 10nF 15 50 R14110K 4
C1815
DECDIG BLANKING BL
C1324n7 C131 2200p 16
PH2LF BCL IN
49 5 BCL
BCL
C133 17 48 C7270.1uF U / B in
PH1LF B / U IN U / B in
+
C120 C1191uF/50V
R138 18 47 C726 0.1uF Y / G in
+ GND3 G / Y IN Y / G in
0.1U/63V 10uF/16V 18K 19 46 C7250.1uF V / R in
DECBG R / V IN V / R in
EW
EW 20
AVL/EWD BLANK
45 BLANK
BLANK
VDRB 21 44 TV AUDIO OUT
VDRB VDRB AUDOUT/AMOUT TV AUDIO OUT
VDRA 22 43 C IN
VDRA VDRA C IN C IN
IF 1 4 23 42 CVBS/Y IN
IF IF1 CVBS/Y IN CVBS/Y IN
C105 2 5 24 41
IF2 GND1
10nF
R151 25 40 C116 1uF TV CVBS IN
+
SAW101 IREF CVBSINT TV CVBS IN
39K
3
SW02B
C135 26
VSC Vp1
39 8V +8v
B AGC 0.1U/63V 27 38
R125 R413 B
AGC TUNER AGC IFVO/SVO
SIF 220 R147 C144 100K
1 4 28 37
SIF AUDEEM/SIF1 PLL IF
2 5 29 36 390 0.1U/63V X-RAY
DECSDEM/SIF2 EHTO X-RAY
Q9362M 27K
2n2 10uF 31
SNDPLL/SIFAGC FBISO
34
1.5nF 2.7K 32 33
NICAM AVL/REFO H. OUT
C139 C140
NO NICAM 330pF 4.7uF AFC
+8V AFC
H-out
H-out
XT160
GNDXT-6.0
XT155Q104 R727
A Q105
GNDXT-5.5
CVBS OUT A
CVBS OUT
C1815 100
R124 C1815
R123
4K7 XT145 4K7
GNDXT-4.5
SYSTEM
NTSC
H_17220_008.eps
5800-A5P190-00 180607
1 2 3 4
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 19
H_17220_011.eps
280607
5800-A5P190-00
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 20
H_17220_012.eps
5800-A5P190-00 280607
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 21
CRT Board
1 2 3 4 5 6 7 8 9 10
B CRT BOARD B
A A
R516
1
R515 220
2
15K
D504
H501 Q506
BF420
BA158
R510
GND 22
Q504
R C4544
B G B
B
BL
Q505
CRT
R511 R513 R512
22
BF421
R514
R R517
2K7
2K2 270 1 KR
270 R527 KG
C502
D503 470PF 2K7 KB
1N4148
R508
2K7
C C
ZD501 C508 R526
8V2
1
82PF R525 220
2
15K
D506
Q509 BA158
BF420
R521 Q507
22
C4544
D D
Q508
BF421
G
R520 R523 R522
CRT AMPLIFY CIRCUIT
E E
R507
1
R506 220
2
15K C507
D502 R528 C506 L501
2
Q503 BA158 NC 10uH
BF420 NC
220K
R501 Q501
SCREEN
FOCUS
EHT
22
C4544
F Q502
F
R504
BF421 B H502
+180V
R502 R503
HEATER
GND
2K2 270 22 R505
1
270
C501
D501 470PF
1N4148
G G
H_17220_013.eps
5800-C3P512-00 190607
1 2 3 4 5 6 7 8 9 10
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 22
D KEY CONTROL D
A A
KEYBOARD CIRCUIT
B
KEYBOARD CIRCUIT B
M001
RD5 RD4 RD3 RD2 RR1 3 2 1
LED RD1
VOL+ VOL- PRO+ PRO-
SW004 SW003 SW002 SW001
LED 100
D D
5
3
1
2
GND 4
KEY
LED
IR
5V
E LED E
KEY
+5V_VCC
IR
F F
G G
H_17220_014.eps
5800-D9SL7Y-05 190607
1 2 3 4 5 6 7 8 9 10
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 23
Layout Keyboard Control Panel (Top Side) Layout Keyboard Control Panel (Bottom Side)
H_17220_038.eps
5800-D9SL7Y-05 H_17220_015.eps 5800-D9SL7Y-05 290607
190607
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 24
E MAINS FILTER E
C603A C603B
Rs T601 4700pF 4700pF
2 3
C603 A B
0.22uF
PTC601 Rp AC250V
D603
CN604
9RM N L D C
1
N CN602 L
FOR CB C603D C603C C607
FOR EMC R600 4700pF 4700pF
C600 L602 NTC 220uF
PFC 15mH×2 5RM 450V
0.1uF/250V C602
0.22uF/250V C604
R602
2
1000pF 200K
CN603
R606 ZD602
C601 R604 C605
39K 6K8 18V
D604 0.1uF
DEGAUSSING 0 100V
R605
0.22uF/250V
220 D605
C606 BA158
VDR601 R603 470pF
GAS DISCHARGE
TUBE
1
7
C609 C608
R601 10nF 10uF
OLP/SS
S/GND
2.2M 1/2W
FB
VCC
OCP/BD
D
2
N
BLUE
CN601 F601
1
AC90-270V BROWN L T3.15A
AC250V H_17220_033.eps
IC601
STR-W6556A
5800-5P190-00 180607
H_17220_017.eps
5800-5P190-00 270607 Layout Mains Filter (Bottom Side)
5800-5P190-00 H_17220_034.eps
270607
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 25
G Side AV Panel G
S-VHS
P702 C785
10uF
ZD707
R779 8V2
75
P701
Side AV Bottom Layer
C777
V IN
10uF
C772
L IN
10uF
C774
R IN
10uF
R777 R780 R778
47K 75 ZD706 ZD709 ZD711
8V2 8V2 8V
SIDE AV IN
H_17220_018.eps
5800-G9SL7Y-05 250607
5800-G9SL7Y-05
H_17220_019.eps
250607
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 26
BTSC Panel
BTSC out L
BTSC out R
TV R
TV L
5800-M5P190-00
H_17460_003.eps
240907
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 27
Layout BTSC Panel (Top Side) Layout BTSC Panel (Bottom Side)
5800-M5P190-00 H_17460_004.eps
240907
5800-M5P190-00 H_17460_005.eps
240907
Circuit Diagrams and PWB Layouts SK5.0A CA 7. EN 28
Personal Notes:
E_06532_013.eps
131004
Alignments SK5.0L CA 8. EN 29
8. Alignments
Index of this chapter: 8.3.3 Screen Voltage Adjust
8.1 General Alignment Conditions
8.2 Hardware Alignments 1. Set picture to “Standard” mode, without signal input.
8.3 Software Alignments 2. Press the keys [i+], “Smart sound” and “Smart picture” to
8.4 Factory mode Settings enter the factory menu. When in “B/W BALANCE” page,
press “mute” on the RC. There will be a level light line
displays.
3. Adjust flyback transformers Screen knob till the level bright
8.1 General Alignment Conditions
line just can be seen.
4. When in the light-line screen, CUT R and CUT G can be
8.1.1 Default Alignment Settings adjusted if needed with the following RC key mapping:
To increase /decrease CUT R (See table 8-1)
Perform all electrical adjustments under the following To increase /decrease CUT G (See table 8-2)
conditions: 5. Press “MUTE” key to return to the “B/W BALANCE” page.
• Power supply voltage: 230 VAC / 50 Hz (± 10%).
• Connect the set to the mains via an isolation transformer Table 8-1 To increase /decrease CUT R
with low internal resistance.
• Allow the set to warm up for approximately 20 to 30
minutes. Function CUT R+ CUT R-
• Measure voltages and waveforms in relation to chassis RC key 1 4
ground (with the exception of the voltages on the primary
side of the power supply). Table 8-2 To increase /decrease CUT G
Caution: never use heatsinks as ground.
• Test probe: 100: 1, Ri > 10 Mohm, Ci < 3.5 pF.
• Use an isolated trimmer/screwdriver to perform Function CUT G+ CUT G-
alignments. RC key 2 5
8.3.2 Focus Fine Adjust 1. Menu OSD position adjustment: Provide a 50/60 Hz cross
hatch pattern. Put the set in MENU mode.
1. Provide a cross-hatch pattern signal. – Press the keys [i+], “Smart sound” and “Smart picture”
2. Set state to “Rich” mode. to enter the factory menu.
3. Adjust flyback transformers Focus knob till picture is clear. – Press the keys [i+] again and “ADJUST” appears on
screen.
2. Press key 4 to enter the factory mode. Adjust VP and HP
item, to obtain menu OSD at the centre of CRT screen.
3. Provide a RGB or YUV cross hatch signal, set the TV in the
standard mode, adjust “YUV OSD HS” till picture horizontal
centre is at the CRT centre (optional).
EN 30 8. SK5.0L CA Alignments
Main Page
"I+"
"0" "1" "2"
ADJUST
Soft Voice
BRIGHT 50 BASS 30
CONTRAST 70 TREBLE 50
COLOR 50 SURROUND OFF
SHARP 70
YUV SHARP 70
COLOR TEMP WARM
Rich Music
BRIGHT 55 BASS 55
CONTRAST 100 TREBLE 60
COLOR 55 SURROUND OFF
SHARP 90
YUV SHARP 90
COLOR TEMP COOL
Natural Theatre
BRIGHT 55 BASS 80
CONTRAST 80 TREBLE 70
COLOR 50 SURROUND ON
SHARP 80
YUV SHARP 80
COLOR TEMP NORMAL
Description of the factory menu Storage address Display string Range (Index value) Default SK5.0L CA
B/W balance
White point R adjustment. 0x00d DRI R 0-63 32 32
White point G adjustment 0x00e DRI G 0-63 32 32
White point B adjustment 0x00f DRI B 0-63 32 32
Black level off-set R adjustment 0x010 CUT R 0-63 32 32
Black level off-set G adjustment. 0x011 CUT G 0-63 32 32
“BRIGHTNESS” of “White Balance Adjustment page” setting 0x02f BT 0-63 32 32
“CONTRAST” of “White Balance Adjustment page” setting 0x030 CT 0-63 32 32
COOL offset according to “DRI R” value of tv, white point R of “COOL” 0x017 COOL DR 0-63 -2 6
COOL offset according to “DRI G” value of tv, white point G of “COOL” 0x018 COOL DG 0-63 0 6
COOL offset according to “DRI B” value of tv, white point B of “COOL” 0x019 COOL DB 0-63 10 13
COOL offset according to “CUT R” value of tv, black level off-set R of “COOL” 0x01a COOL CR 0-63 0 0
COOL offset according to “CUT G” value of tv, black level off-set R of “COOL” 0x01b COOL CG 0-63 0 0
WARM offset according to “DRI R” value of tv, white point R of “COOL” 0x01c WARM DR 0-63 10 7
Warm offset according to “DRI G” value of tv, white point G of “COOL” 0x01d WARM DG 0-63 0 0
Warm offset according to “DRI B” value of tv, white point B of “COOL” 0x01e WARM DB 0-63 0 -6
Warm offset according to “CUT R” value of tv, black level off-set R of “COOL” 0x01f WARM CR 0-63 0 0
Warm offset according to “CUT G” value of tv, black level off-set R of “COOL” 0x020 WARM CG 0-63 0 0
Direct key “0”
50hz/60hz Frequency 60 Hz
Horizontal center ox008 H PH 0-TV-63-TV 31-TV 33-TV
Vertical slope ox009 V SL 0-63 24 40
Vertical center ox00a V SH 0-63 21 28
Vertical amplitude. ox00b V SI 0-63 33 51
Vertical s-correction. ox00c V SC 0-63 27 27
EW WIDTH 0x04b EW WIDTH 0-63 32 45
EW parabola/width 0x04c EW PARA 0-63 32 49
EW upper/lower corner parabola 0x04d UP CORNER 0-63 32 28
Bottom curve 0x04e LO CORNER 0-63 32 34
Horizontal parallelogram 0x04f H-PARA 0-63 32 35
Horizontal bow 0x050 H-BOW 0-63 32 39
EW trapezium 0x051 EW TRAPE 0-63 32 21
Expand 4:3 mode horizontal WIDTH adjust 0x0ed(bit4) ZOOM 0-63 44 44
50hz/60hz Frequency 50 Hz
Horizontal center 0x003 H PH 0-TV-63-TV 31-TV 31-TV
Vertical slope 0x004 V SL 0-63 24 40
Vertical center 0x006 V SH 0-63 21 28
Vertical amplitude. 0x005 V SI 0-63 33 52
Vertical s-correction. 0x007 V SC 0-63 27 27
EW WIDTH 0x044 EW WIDTH 0-63 32 45
EW parabola/width 0x045 EW PARA 0-63 32 48
EW upper/lower corner parabola 0x046 UP CORNER 0-63 32 32
Bottom curve 0x047 LO CORNER 0-63 32 32
Horizontal parallelogram 0x048 H-PARA 0-63 32 35
Horizontal bow 0x049 H-BOW 0-63 32 32
EW trapezium 0x04a EW TRAPE 0-63 32 26
Expand 4:3 mode horizontal WIDTH adjust 0x062 ZOOM 0-63 44 44
Horizontal center in AV source. 0x05e H PH +5-AV 32 32
Horizontal center in AV source. 0x05f H PH +5-AV 32 32
Horizontal center in YUV source. 0x05c H PH +0-YUV 32 32
Horizontal center in YUV source. 0x05d H PH +0-YUV 32 32
Direct key “1”
Out of box setting, Smart Picture: Rich, Contrast +: On, NR: Off, SHIPMODE OFF ON
Smart Sound: Theatre, Tuner Mode: Auto, Volume: 30, CC: Off
RF.AGC adjust 0x002 AGC 0-63 24 32
AGC speed 0x0de (bit5, bit4) AGC SPEED 0-63 1 1
IF choose 0x0dd (bit7, bit6) IF 58.75 Mhz 45.75 Mhz 45.75 Mhz 45.75 Mhz
HRC and IRC of N system for auto search selection 0x0ea (bit4) HRC & IRC OFF ON OFF OFF
ON: PAL M/N ON, OFF: PAL M/N OFF 0x0ea (bit1) MULTI SYSTEM OFF ON ON ON
White apex limit 0x0cb (bit7-bit4) PWL 0-15 0 15
X ray protect 0x0e1 (bit2, bit3) XDT 0-2 1 1
X ray protection detect count 0x073 XDT COUNT 0-255 30 30
NTSC decode matrix 0x0e7(bit2) MUS USA JAP USA USA
PAL, NTSC decode matrix 0x0ed (bit0) MAT OFF ON OFF ON
Bypass of sound bandpass filter 0x0e1 (bit5, bit4) BPB 0-2 1 1
Video dependent coring 0x0de (bit3, bit2) CORING 0-3 3 3
Switch-off in vertical overscan 0x0e7 (bit7) OSO OFF ON ON ON
Direct key “2”
UOC control volume switch 0x0e8 (bit7) UOC VOL SW OFF ON OFF OFF
UOC/PWM modify volume value 0x02e UOC/PWM VOL 0-63 41 40
Volume of 9859 modify value when sound is mono 0x052 MONO GAIN 0-63 48 52
EN 32 8. SK5.0L CA Alignments
Description of the factory menu Storage address Display string Range (Index value) Default SK5.0L CA
Volume of 9859 modify value when sound is stereo 0x053 STEREO GAIN 0-63 48 52
Volume of 9859 modify value when sound is SAP 0x054 SAP GAIN 0-63 48 50
Volume of 9859 modify value when system is AV state 0x055 AV GAIN 0-63 48 48
9859 control pin output state 0x0e0 (bit3, bit2) 9859INPUT 0-2 2 0
10% volume point 0x026 VOL 10 0-100 25 20
25% volume point 0x027 VOL 25 0-100 50 45
50% volume point 0x028 VOL 50 0-100 75 60
80% volume point 0x029 VOL 80 0-100 90 80
100% volume point 0x02a VOL 100 0-100 100 100
FM demodulate frequency width 0x0de (bit1, bit0) FMWS 0-2 0 0
AVL function switch 0x0e8 (bit6) AVL OPT OFF ON OFF OFF
Direct key “3”
AV control logic choose 0x0e1 (bit7, bit6) AV OPT 0-3 1 0
AV choose 0x0cc (bit7-bit4) AV CFG 0-7 3 3
AV2 choose 0x0ea (bit5) 2 AV OFF ON OFF OFF
DVD choose 0x0e9 (bit4) YC/DVD OFF ON OFF OFF
Video output 0x0e7 (bit4) VIDEO OUT IF CVBS CVBS CVBS
Pin 5 choose function 0x0cc (bit3-bit0) PIN 5 NTSC NTSC
Pin 7 choose function 0x0cd (bit7-bit4) PIN 7 VOL1 VOL1
Pin 8 choose function 0x0cd (bit3-bit0) PIN 8 MUTE MUTE
MUTE pin mode 0x0e9 (bit0) MUTEPIN OFF ON OFF
MODE
OFF: Pin 7 control volume curve 0x0ee (bit6) MUTEPIN SEL OFF
ON: Pin 4 control volume curve
CCD Horizontal width adjust 0x05a CC HP 0-15 13 13
CCD scan Horizontal row when PAL N system 0x060 CC LINE 0-60 21 21
CCD delay adjustment 0x0d1 (bit3-bit0) CC DELAY 8-23 20 12
Direct key “4”
OSD up down position 0x02b VP 0-63 52 51
OSD left right position 0x02c HP 0-63 54 42
RGB/YUV OSD Horizontal Center 0x05b YUV OSD HS 0-60 38 44
OSD output contrast 0x0df (bit7, bit6) OSD L 0-3 0 0
Menu translucence 0x0e9 (bit1) HALFTONE OFF ON ON ON
Software version number SOFTWARE
VERSION
NUMBER
Direct key “5”
Sound mode BTSC-MODE MONO STEREO SAP
Stereo noise limit 0x0ce (bit7-bit4) BTSC-ST 0-15 0 0
SAP noise limit 0x0ce(bit3-bit0) BTSC-SP 0-15 0 0
Sound input level adjustment 0x040 BTSC-LI 0-15 7 9
Separate 0x041 BTSC-A1 0-31 23 14
Separate 0x042 BTSC-A2 0-31 22 6
Time constant 0x0cf (bit7-bit4) BTSC-TC 0-7 4 3
Stereo level switch 0x0e8 (bit3) BTSC-STS OFF ON OFF ON
Stereo adjustment on/off 0x0e8 (bit2) BTSC-ADJ BUSY START START START
MTS detect time delay 0x001 MTS DETECT 0-255 50 50
STEREO and SAP detect count 0x072 MTS FILTER 0-255 20 20
MONO detect count 0x074 MTS FILTER2 0-255 20 3
Direct key “6”
POWER ON MODE 0x0dd (bit3, bit2) POW 0-2 2 2
POWER ON time delay 0x0cb (bit3-bit0) POWER ON TIM 2-17 12 12
Black current stabilization 0x0e8 (bit0) AKB OFF ON ON ON
Black current loop detect 0x0e9 (bit7) NBL OFF ON ON ON
WATCH DOG 0x0eb (bit7) WATCHDOG OFF ON OFF ON
ON: Philips RC 0x0eb (bit6) PHILIPS RC OFF ON ON ON
OFF: Skyworth RC
VCHIP FUNCTION SWITCH 0x0ea (bit7) VCHIP OFF ON OFF OFF
GAME FUNCTION SWITCH 0x0eb (bit5) GAME OFF ON OFF OFF
CALENDER FUNCTION SWITCH 0x0eb (bit4) CALENDER OFF ON OFF OFF
4:3 expand function choose 0x0ec (bit6) ZOOM OPT OFF ON ON ON
ON: Blue Screen 0x0e9 (bit6) BLUE BLACK OFF ON ON ON
OFF: Black Screen
EW WIDTH offset according to “EW WIDTH” value when TV is no signal 0x06d BB WIDTH 53-10 +0 1
Video mute during change to program 0x0e1 (bit1, bit0) BLACK BACK 0-2 0 0
RGB BLANKING 0x0ee (bit7) RGB BLANKING OFF ON ON ON
Direct key “7”
Sub contrast 0x057 SUB BRI 0-63 0 3
Sub brightness 0x059 SUB CON 0-63 0 2
Sub color 0x023 SUB COL 0-63 30 30
Alignments SK5.0L CA 8. EN 33
Description of the factory menu Storage address Display string Range (Index value) Default SK5.0L CA
Sub Sharpness 0x024 SUB SHA 0-63 32 32
TV Sub tint 0x025 SUB TIN 0-31 16 16
AV Sub tint 0x075 SUB TIN-AV 0-31 16 16
PAL Luminance delay 0x0c9 (bit3-bit0) YDL PAL 0-15 2 10
NTSC Luminance delay 0x0c9 (bit7-bit4) YDL NTSC 0-15 2 10
AV Luminance delay 0x0ca(bit7-bit4) YDL AV 0-15 4 10
Maximum brightness 0x056 MAX BRI 0-63 63 52
Middle brightness 0x021 MID BRI 0-63 18 27
Maximum contrast 0x058 MAX CON 0-63 63 63
Middle contrast 0x022 MID CON 0-63 15 28
Line-level of brightness 0x02d SC.BRI 0-63 8 8
Direct key “8”
YUV offset according to “DRI R” value of TV, white point R of YUV. 0x012 YUV DR (-32) - (+31) +0 +0
YUV offset according to “DRI G” value of TV, white point G of YUV 0x013 YUV DG (-32) - (+31) +0 +0
YUV offset according to “DRI B” value of TV, white point B of YUV 0x014 YUV DB (-32) - (+31) +0 +0
YUV offset according to “CUT R” value of TV, black level offset R of YUV 0x015 YUV CR (-32) - (+31) +0 +0
YUV offset according to “CUT G” value of TV, black level offset G of YUV 0x016 YUV CG (-32) - (+31) +0 +0
English OSD switch 0x0eb (bit3) ENGLISH OFF ON ON ON
Spanish OSD switch 0x0eb (bit2) SPANISH OFF ON ON ON
French OSD switch 0x0eb (bit1) FRANCE OFF ON OFF OFF
Portuguese OSD switch 0x0eb (bit0) PORTUGUESE OFF ON ON ON
External Y (Luminance) input gain during YPRPB. 0x0ee (bit4) YGN OFF ON OFF ON
OFF: gain 0 dB reduced, ON: gain 3 dB reduced
Cathode drive level 0x0ca (bit3-bit0) CATHE 3 3
EHT tracking mode 0x0ea (bit6) HCO ON ON
Black current measuring lines in overscan 0x0e9 (bit2) OSVE OFF OFF
Manual INIT E2PROM
INITEEP
Key “Smart sound”
BASS set value in Voice state 0x064 BASS 30 30
TREBLE set value in Voice state 0x065 TREBLE 50 50
SURROUND set value in Voice state 0x066 SURROUND OFF OFF
BASS set value in Music state 0x067 BASS 55 55
TREBLE set value in Music state 0x068 TREBLE 60 60
SURROUND set value in Music state 0x069 SURROUND OFF OFF
BASS set value in Theatre state 0x06a BASS 80 80
TREBLE set value in Theatre state 0x06b TREBLE 70 70
SURROUND set value in Theatre state 0x06c SURROUND ON ON
Key “Smart image”
Bright set value in Soft state 0x036 BRIGHT 55 55
Contrast set value in Soft state 0x037 CONTRAST 50 50
Color set value in Soft state 0x038 COLOR 45 45
Sharpness set value in Soft state 0x039 SHARP 45 45
Sharpness set value in Soft state of YUV 0x070 YUV SHARP 50 50
COLOR TEMP set value in Soft state 0x03a COLOR TEMP WARM WARM
Bright set value in Rich state 0x03b BRIGHT 70 70
Contrast set value in Rich state 0x03c CONTRAST 85 85
Color set value in Rich state 0x03d COLOR 70 70
Sharpness set value in Rich state 0x03e SHARP 70 70
Sharpness set value in Rich state of YUV 0x071 YUV SHARP 80 80
COLOR TEMP set value in Rich state 0x03f COLOR TEMP COOL COOL
Bright set value in Natural state 0x031 BRIGHT 50 50
Contrast set value in Natural state 0x032 CONTRAST 75 75
Color set value in Natural state 0x033 COLOR 50 50
Sharpness set value in Natural state 0x034 SHARP 50 50
Sharpness set value in Natural state of YUV 0x06f YUV SHARP 50 50
COLOR TEMP set value in Natural state 0x035 COLOR TEMP NORMAL NORMAL
EN 34 9. SK5.0L CA Circuit Descriptions, Abbreviation List, and IC Data Sheets
SAP Demodulator
9.1 Introduction
The composite signal is fed from the output of the input level
adjustment stage to the SAP demodulator circuit through a 5fH
The SK5.0L CA is a CRT TV for the year 2007, based on the band-pass filter. The demodulator level is automatically
5P19 platform. In this chapter, only a general description of the controlled. The SAP demodulator includes an internal field
various circuits is given. For more detailed information, see the strength detector that mutes the SAP output in the event of
circuit diagrams in this manual. insufficient signal conditions. The SAP identification signal can
be read by the I2C-bus.
9.2 The various circuits
Noise Detector
The composite input noise increases with decreasing antenna
9.2.1 Tuner
signal. This makes it necessary to switch stereo or SAP off at
certain thresholds. These thresholds can be set via the I2C-
The function of the tuner is to select the channel to be received bus. With ST0 to ST3 the stereo threshold can be selected and
and suppress the interference of neighboring channels, to
with SP0 to SP3 the SAP threshold. A hysteresis can be
amplify the high frequency signal, to improve the receiving
achieved via software by making the threshold dependent of
sensitivity and SNR, and to generate a PIF signal through the identification bits STP and SAPP.
frequency conversion.
Mode Selection
9.2.2 IF Channel
The stereo/SAP switch feeds either the L - R signal or the SAP
demodulator output signal via the internal dbx noise reduction
The IF Channel mainly ensures the sensitivity and selectivity of circuit to the dematrix/switching circuit. Different switch modes
the complete TV set. The IF AMP integrated in the UOCIII is provided at the output pins OUTR and OUTL are available.
made up of a three-stage dual-differential amplifier with a gain
value above 70dB, a SNR of 55dB and a bandwidth of 7 MHz. dbx Decoder
The video demodulation circuit is made from the built-in PLL The dbx circuit includes all blocks required for the noise
Sync Detector. The spectrum of the demodulation carrier is
reduction system in accordance with the BTSC system
unitary and it is not affected by the content of the video signal.
specification. The output signal is fed through a 73 ms fixed de-
The tuner features stable receptivity while the signal output emphasis circuit to the dematrix block.
from the video detector features high fidelity. The built-in PLL
circuit of the UOCIII generates a 38.0 MHz or 38.9 MHz
SAP Output
demodulation reference signal for the sync detector to
demodulate the video signal; this is called “PLL sync Independent of the stereo/SAP switch, the SAP signal is also
available at pin SAP. At SAP, the SAP signal is not dbx
demodulation”.
decoded. The capacitor at SDE provides a recommended de-
emphasis (150 ms) at SAP.
9.2.3 Sound Channel
Integrated Filters
An external ceramic filter is used to select the second SIF
The filter functions necessary for stereo and SAP demodulation
signal for the sound channel of UOCIII from the signal output of
and part of the dbx filter circuits are provided on-chip using
the video detector. The audio signal is obtained after limiting transconductor circuits. The required filter accuracy is attained
amplification and demodulation by the intermediate frequency
by an automatic filter alignment circuit.
detector for the SIF signal, and then the audio signal is fed to
the BTSC stereo/SAP decoder TDA9850. From that it is output
to the audio amplifier TFA9842, which drives the speakers to 9.2.5 CRT Drive Circuit
provide the sound. The intermediate frequency detector and
volume-control attenuator that are built in the UOCIII are set In the driver circuit, both the voltage and current of the R/G/B
and adjusted via the CPU. signal are amplified, after which the CRT drive circuit
modulates the cathode beam current of the CRT. The R/G/B
signal input into the driver circuit is of negative polarity.
9.2.4 BTSC stereo/SAP decoder
H_17210_039.eps
120607
H_17210_039.eps
120607
Block Diagram
THERMAL TDA4865AJ
PROTECTION
DIFFERENTIAL
VERTICAL FLYBACK REFERENCE
INPUT
OUTPUT GENERATOR CIRCUIT
STAGE
7 6 5 4 3 2 1
INP INN VOUT GND VP2 VP3 VP1
RS1 CS1 CF
D1
C2
deflection R5
RP
coil
R3
C1
R6
from
deflection controller R1
R2
VN VP
Pin Configuration
VP1 1
VP3 2
VP2 3
GND 4 TDA4865AJ
VOUT 5
INN 6
INP 7
H_17210_035.eps
120607
Block Diagram
Pin Configuration
H_17210_041.eps
120607
Block Diagram
VCC
9
4 8
IN1 OUT1
60
kΩ
1 2
IN2 OUT2
60
kΩ
3 SHORT-CIRCUIT
CIV AND
TEMPERATURE
VREF
PROTECTION
VCC
7 VOLUME
VC
CONTROL
0.5VCC 6
SVR
TFA9842AJ
GND
Pin Configuration
IN2 1
OUT2 2
CIV 3
IN1 4
GND 5 TFA9842AJ
SVR 6
VC 7
OUT1 8
VCC 9
H_17210_033.eps
110607
Block Diagram
C3 +
C4 ceramic
C2 + C5 Q1 resonator C6 + C7 +
R1
13 14 15 16 17 18 19
L+R stereo
27
DEMATRIX OUTL mono
+ SAP
STEREO DECODER MODE to
L − R/SAP 21
SELECT OUTR audio
processing
TDA9850
C8
22
composite INPUT NOISE STEREO/SAP
11 DE-EMPHASIS
+
7
SAP STEREO SUPPLY LOGIC, I2C-
DBX ADJUST TRANSCEIVER
DEMODULATOR 28
MAD
5 4 26 3 1 2 32 31 30 29 25 20 10 12 6 24 8 9
R2
+ + + + + + + + + +
C16 C15 C17 C19 C18
C14 C12 C11 C10 C9 CL CR
R3 SDA SCL
Pin Configuration
VEO 1 32 CS
VEI 2 31 CW
CNR 3 30 CTS
CM 4 29 CTW
CDEC 5 28 MAD
AGND 6 27 OUTL
DGND 7 26 CND
SDA 8 25 CL
TDA9850
SCL 9 24 Vref
VCC 10 23 SAP
COMP 11 22 CSDE
VCAP 12 21 OUTR
CP1 13 20 CR
CP2 14 19 CSS
CPH 15 18 CMO
CADJ 16 17 CER
H_17450_004.eps
200907
Block Diagram
H_17210_034.eps
130607
Pin Configuration
H_17210_029.eps
130607
H_17210_030.eps
130607
Pinning
H_17210_031.eps
130607
Block Diagram
QSSO/AMOUT/AUDEXT
AUDOUT/AMOUT
ADC IN (4x)
SOUND
VST OUT
RESET
TRAP
SIFIN
VPE
TUNERAGC
IFVO/SVO
REF
H
VIDEO SWITCH LUMA DELAY
CLOSED CAPTION OSD
VIDEO IDENT. CVBS
CVBS/Y PEAKING ROM/RAM
ACQUISITION V DISPLAY
VIDEO FILTERS BLACK STRETCH
C
SYNC COR R G B BL
REF RO
CONTR/BRIGHTN
BASE-BAND OSD/TEXT INSERT GO
PAL/NTSC
(REFOUT) BO
DECODER DELAY LINE CCC
WHITE-P. ADJ. BCLIN
BLKIN
R G B
Pin Configuration
handbook, halfpage
P1.3/T1 1 64 P1.2/INT0
P1.6/SCL 2 63 P1.1/T0
P1.7/SDA 3 62 P1.0/INT1
P2.0/TPWM 4 61 VDDP
P3.0/ADC0/PWM0 5 60 RESET
P3.1/ADC1/PWM1 6 59 XTALOUT
P3.2/ADC2/PWM2 7 58 XTALIN
P3.3/ADC3/PWM3 8 57 OSCGND
VSSC/P 9 56 VDDC
P0.5 10 55 VPE
P0.6 11 54 VDDA
TDA937X PS/N2 series (SDIP-64)
VSSA 12 53 BO
I.C. 13 52 GO
VP2 14 51 RO
DECDIG 15 50 BLKIN
16 49 BCLIN
PH2LF
XXX
PH1LF 17 48 B2/U/PBIN
GND3 18 47 G2/YIN
DECBG 19 46 R2/V/PRIN
AVL/EWD/ 20 45 INSSW2
DECSDEM
VDRB 21 44 AUDOUT
VDRA 22 43 C
IFIN1 23 42 CVBS/Y
IFIN2 24 41 GND1
IREF 25 40 CVBS1
VSC 26 39 VP1
AGCOUT 27 38 IFVO/SVO
AUDEEM/SIFIN1 28 37 PLLIF
DECSDEM/SIFIN2 29 36 EHTO
GND2 30 35 AUDEXT/QSSO
31 34 FBISO
SNDPLL/SIFAGC
AVL/SNDIF/REFO/ 32 33 HOUT
H_17450_012.eps
AUDEEM 210907
H_17210_035.eps
120607
Pin Configuration
H_17210_036.eps
120607
R137 9965 000 40304 CFR 1KΩ 1/16W R632 9965 000 40513 MOFR 1Ω
R138 9965 000 40688 CFR 18kΩ 1/16W R633 9965 000 40108 CFR 5.1kΩ d
R139 9965 000 40693 CFR 2.7kΩ 1/16W R634 9965 000 39976 CFR 10kΩ 1/16W
R140 9965 000 39975 CFR 100Ω 1/16W R635 9965 000 39980 CFR 22kΩ 1/8W D402 9965 000 40218 1N4148 150mA/100V
R141 9965 000 39976 CFR 10kΩ 1/16W R638 9965 000 41085 MOFR 22Ω D403 9965 000 40224 Zener 8V2 1/2W 5%
R142 9965 000 39975 CFR 100Ω 1/16W R639 9965 000 39976 CFR 10kΩ 1/16W D404 9965 000 40218 1N4148 150mA/100V
R143 9965 000 39975 CFR 100Ω 1/16W R643 9965 000 40701 CFR 47kΩ 1/16W D430 9965 000 40569 BY228
R144 9965 000 39975 CFR 100Ω 1/16W R644 9965 000 39976 CFR 10kΩ 1/16W D431 9965 100 04906 3A/800V(DO-27)
R145 9965 000 39980 CFR 22kΩ 1/8W R645 9965 100 04844 390Ω 5% 1/6W D433 9965 000 40219 BA158 600V/1A
R147 9965 000 40687 CFR 1.8kΩ 1/16W R647 9965 100 05394 RESIS 0.51 OHM 1W 5% D450 9965 100 05390 TBYW362A/600V
R148 9965 000 40695 CFR 3.3kΩ 1/16W R648 9965 000 39980 CFR 22kΩ 1/8W D451 9965 100 05390 TBYW362A/600V
R149 9965 000 40695 CFR 3.3kΩ 1/16W R649 9965 000 40000 CFR 2.2kΩ D452 9965 000 40219 BA158 600V/1A
R151 9965 000 40122 MOFR 39kΩ R650 9965 100 05380 430Ω 5% 1/16-1/6W D501 9965 000 40218 1N4148 150mA/100V
R401 9965 000 40700 CFR 4.7kΩ 1/16W R701 9965 000 40701 CFR 47kΩ 1/16W D502 9965 000 40219 BA158 600V/1A
R404 9965 000 39975 CFR 100Ω 1/16W R702 9965 000 40701 CFR 47kΩ 1/16W D503 9965 000 40218 1N4148 150mA/100V
R405 9965 100 04848 5.6kΩ 5% 1/16-1/6W R705 9965 000 40687 CFR 1.8kΩ 1/16W D504 9965 000 40219 BA158 600V/1A
R406 9965 000 40774 MOFR 1kΩ R706 9965 000 40687 CFR 1.8kΩ 1/16W D505 9965 000 40218 1N4148 150mA/100V
R407 9965 000 40001 CFR 22kΩ R707 9965 000 40701 CFR 47kΩ 1/16W D506 9965 000 40219 BA158 600V/1A
R409 9965 100 04841 27kΩ 5% 1/16-1/6W R708 9965 000 40701 CFR 47kΩ 1/16W D603A 9965 100 05391 Rectifier 800V/1.5A
R412 9965 100 04841 27kΩ 5% 1/16-1/6W R709 9965 000 40701 CFR 47kΩ 1/16W D603B 9965 100 05391 Rectifier 800V/1.5A
R413 9965 000 39977 CFR 100kΩ R710 9965 000 40701 CFR 47kΩ 1/16W D603C 9965 100 05391 Rectifier 800V/1.5A
R414 9965 000 40698 CFR 39kΩ 1/16W R711 9965 000 39984 CFR 75Ω 1/16W D603D 9965 100 05391 Rectifier 800V/1.5A
R416 9965 000 40304 CFR 1KΩ 1/16W R713 9965 000 39980 CFR 22kΩ 1/8W D605 9965 000 40219 BA158 600V/1A
R417 9965 000 40695 CFR 3.3kΩ 1/16W R717 9965 000 40705 CFR 68Ω 1/16W D620 9965 100 07483 High Speed Rect. RU4
R419 9965 100 05142 270kΩ 5W 1/16-1/6W R719 9965 000 39975 CFR 100Ω 1/16W D621 9965 000 40219 BA158 600V/1A
R420 9965 000 39988 CFR 1kΩ 1/4W R721 9965 000 39984 CFR 75Ω 1/16W D622 9965 100 05390 TBYW362A/600V
R421 9965 100 04838 180Ω 5% 1/16-1/6W R722 9965 000 39975 CFR 100Ω 1/16W D623 9965 100 05406 HSRD 200V/3A
R422 9965 100 04849 680Ω 5% 1/16-1/6W R723 9965 000 39984 CFR 75Ω 1/16W D626 9965 000 40219 BA158 600V/1A
R423 9965 100 07328 6.2Ω 5% 2W R724 9965 000 39982 CFR 33kΩ 1/16W D627 9965 000 40218 1N4148 150mA/100V
R424 9965 000 40689 CFR 2kΩ 1/16W R725 9965 000 39976 CFR 10kΩ 1/16W D761 9965 000 40218 1N4148 150mA/100V
R425 9965 100 04841 27kΩ 5% 1/16-1/6W R727 9965 000 39975 CFR 100Ω 1/16W D762 9965 000 40218 1N4148 150mA/100V
R432 9965 000 40491 CFR 270Ω 1W R728 9965 000 40304 CFR 1KΩ 1/16W D763 9965 000 40218 1N4148 150mA/100V
R433 9965 000 40520 Fusible Res. 0.33Ω 1W R729 9965 100 04836 1.2kΩ 5% 1/16-1/6W
R440 9965 100 07699 Fusible Res. 2.2Ω 2W R742 9965 100 05138 13kΩ 5% 1/16-1/6W
R441 9965 100 05218 56kΩ 5% 1/16-1/6W R743 9965 100 05138 13kΩ 5% 1/16-1/6W c e
R443 9965 000 40699 CFR 470Ω 1/16W R744 9965 000 40701 CFR 47kΩ 1/16W
R450 9965 100 05160 0.22Ω 5% 2W R745 9965 000 40701 CFR 47kΩ 1/16W IC101 9965 100 07701 uP
R451 9965 100 05160 0.22Ω 5% 2W R746 9965 000 40701 CFR 47kΩ 1/16W IC102 9965 000 40597 8k-BIT IIC EEPROM
R452 9965 100 05395 RESIS 5.6 OHM 1W 5% R747 9965 000 40701 CFR 47kΩ 1/16W IC103 9965 000 40249 KA33V
R453 9965 000 41086 MOFR 270Ω R748 9965 000 39979 CFR 150Ω 1/6W IC104 9965 000 40247 L7808CV
R454 9965 000 41087 MOFR 33Ω R763 9965 000 40686 CFR 15kΩ 1/16W IC301 9965 100 04918 TDA4865AJ DBS7P
R457 9965 000 39975 CFR 100Ω 1/16W R764 9965 000 40704 CFR 6.2kΩ 1/16W IC601 9965 100 05407 W6556A SANKEN
R459 9965 000 40687 CFR 1.8kΩ 1/16W R765 9965 000 40304 CFR 1KΩ 1/16W IC621 9965 100 05369 SE120N SANKEN (120V)
R460 9965 000 39975 CFR 100Ω 1/16W R766 9965 000 40701 CFR 47kΩ 1/16W IC622 9965 000 40601 PC817C Sharp
R461 9965 000 39985 CFR 5.6Ω R768 9965 100 05150 91kΩ 5% 1/4W IC740 9965 000 40596 TDA9859
R462 9965 100 05312 0.82Ω 2W R769 9965 000 40304 CFR 1KΩ 1/16W IC760 9965 100 04917 TFA9842AJ PHILIPS
R463 9965 000 40138 MOFR 220Ω R770 9965 000 40304 CFR 1KΩ 1/16W IC761 9965 000 40309 HCF4052BF SGS
R464 9965 100 05624 NTC 50kΩ 5% R771 9965 000 39976 CFR 10kΩ 1/16W IC762 9965 000 40309 HCF4052BF SGS
R466 9965 000 40698 CFR 39kΩ 1/16W R775 9965 000 40701 CFR 47kΩ 1/16W IC851 9965 100 07712 TDA9850 (IIC Bus)
R467 9965 000 39980 CFR 22kΩ 1/8W R776 9965 000 40701 CFR 47kΩ 1/16W IC852 9965 100 07713 L78L09CZ SGS TO-92
R468 9965 100 07705 MOFR R777 9965 000 40701 CFR 47kΩ 1/16W Q101 9965 000 40237 2SC2717
R469 9965 000 40524 NTC 5/5A R778 9965 000 39975 CFR 100Ω 1/16W Q106 9965 000 40232 2SC1815Y/2PC1815
R501 9965 000 39998 CFR 22Ω 1/4W R779 9965 000 39984 CFR 75Ω 1/16W Q107 9965 000 40232 2SC1815Y/2PC1815
R502 9965 000 40000 CFR 2.2kΩ R780 9965 000 40701 CFR 47kΩ 1/16W Q401 9965 000 40234 2SC2482/3DG2482Y
R503 9965 000 40491 CFR 270Ω 1W R851 9965 100 04839 2.2kΩ 5% 1/6W Q440 9965 000 41191 Trans. FQPF630
R504 9965 000 39998 CFR 22Ω 1/4W R852 9965 100 05146 8.2kΩ 5% 1/16-1/6W Q501 9965 000 40585 2SC4544/3DA4544Y
R505 9965 000 40509 MOFR 270Ω R853 9965 000 39979 CFR 150Ω 1/6W Q502 9965 000 40239 BF423 PNP (-250V)
R506 9965 000 40517 MOFR 15kΩ R854 9965 000 39986 CFR 10Ω 1/4W Q503 9965 000 40238 BF422 NPN (250V)
R507 9965 000 40129 MOFR 220Ω R855 9965 000 39975 CFR 100Ω 1/16W Q504 9965 000 40585 2SC4544/3DA4544Y
R508 9965 000 40525 CCR 2.7kΩ R856 9965 000 39975 CFR 100Ω 1/16W Q505 9965 000 40239 BF423 PNP (-250V)
R510 9965 000 39998 CFR 22Ω 1/4W R857 9965 000 39976 CFR 10kΩ 1/16W Q506 9965 000 40238 BF422 NPN (250V)
R511 9965 000 40000 CFR 2.2kΩ R858 9965 000 39976 CFR 10kΩ 1/16W Q507 9965 000 40585 2SC4544/3DA4544Y
R512 9965 000 39998 CFR 22Ω 1/4W R860 9965 000 40304 CFR 1KΩ 1/16W Q508 9965 000 40239 BF423 PNP (-250V)
R513 9965 000 40491 CFR 270Ω 1W RL601 9965 100 05413 OMIT-SS-112LM Q509 9965 000 40238 BF422 NPN (250V)
R514 9965 000 40509 MOFR 270Ω VDR601 9965 000 40275 Gas Tube CMQX0680 Q621 9965 000 40232 2SC1815Y/2PC1815
R515 9965 000 40517 MOFR 15kΩ Q622 9965 000 40232 2SC1815Y/2PC1815
R516 9965 000 40129 MOFR 220Ω Q623 9965 000 40232 2SC1815Y/2PC1815
R517 9965 000 40525 CCR 2.7kΩ b Q624 9965 100 04912 2SA1013
R520 9965 000 40000 CFR 2.2kΩ Q625 9965 000 40232 2SC1815Y/2PC1815
L101 9965 000 40602 Peaking coil 1μH 10% Q626 9965 000 40232 2SC1815Y/2PC1815
R521 9965 000 39998 CFR 22Ω 1/4W
L103 9965 100 07711 Peaking coil 12μH 10% Q701 9965 000 40232 2SC1815Y/2PC1815
R522 9965 000 39998 CFR 22Ω 1/4W
L104 9965 000 40252 Peaking coil 10μH 10% Q702 9965 000 40232 2SC1815Y/2PC1815
R523 9965 000 40491 CFR 270Ω 1W
L105 9965 000 40252 Peaking coil 10μH 10% Q703 9965 000 40232 2SC1815Y/2PC1815
R524 9965 000 40509 MOFR 270Ω
L106 9965 000 40252 Peaking coil 10μH 10% Q760 9965 000 40231 2SA1015Y\2PA1015
R525 9965 000 40517 MOFR 15kΩ
L430 9965 100 07718 Linear Coil 36μH Q761 9965 000 40232 2SC1815Y/2PC1815
R526 9965 000 40129 MOFR 220Ω
L431 9965 100 05629 Chock Coil 160μH 10% Q851 9965 000 40232 2SC1815Y/2PC1815
R527 9965 000 40525 CCR 2.7kΩ
L432 9965 100 04924 Choke Coil 790μH A101 9965 100 07704 TUNER
R528 9965 000 40503 CFR 220kΩ 1W
L440 9965 100 07717 Choke Coil 2.8MHz 10% J120 9965 000 40304 CFR 1KΩ 1/16W
R529 9965 000 40492 CFR 33Ω 0.25W
L501 9965 000 40252 Peaking coil 10μH 10% J615 9965 000 39976 CFR 10kΩ 1/16W
R600 9965 000 40524 NTC 5/5A
R601 9965 100 05373 2.2MΩ 5% 1/2W L601 9965 000 40607 AC Line Filter 15MHz N401 9965 000 40588 2SD2553/3DD2553 1.7
R602 9965 100 05397 200kΩ 5% 2W L603 9965 100 05411 AC Line Filter 15mH
L604 9965 000 41227 Bead 3.5 x 1 x 9mm
R604 9965 000 40698 CFR 39kΩ 1/16W
R605 9965 000 40691 CFR 220Ω 1/16W L701 9965 000 40311 Peaking coil 33μH 10% Keyboard & Control Panel [D]
R606 9965 000 40706 CFR 6.8kΩ 1/16W L702 9965 000 40311 Peaking coil 33μH 10%
L703 9965 000 40254 Peaking coil 15μH 10%
R607 9965 000 40128 MOFR 22Ω Various
R608 9965 000 40000 CFR 2.2kΩ L704 9965 000 40254 Peaking coil 15μH 10%
R609 9965 100 05410 Coke 200μH L705 9965 000 40254 Peaking coil 15μH 10%
L706 9965 000 40254 Peaking coil 15μH 10% SW001 9965 100 05199 Tact Switch
R610 9965 000 40154 High Volt. 8.2MΩ 1W SW002 9965 100 05199 Tact Switch
R621 9965 100 05160 0.22Ω 5% 2W T401 9965 100 05412 Transformer BCT-19G
T402 9965 100 05371 29" Flyback Transformer SW003 9965 100 05199 Tact Switch
R622 9965 100 05160 0.22Ω 5% 2W SW004 9965 100 05199 Tact Switch
T603 9965 100 05372 Switching Transformer
R624 9965 100 05160 0.22Ω 5% 2W SW601 9965 100 05423 MPS.SDDF-3-03 W
R627 9965 100 05366 6.2kΩ 5% 1/4W
R630 9965 000 40113 CFR 680Ω
R631 9965 000 39988 CFR 1kΩ 1/4W
Spare Parts List SK5.0L CA 10. EN 53
g
C001 9965 000 40529 33pF 50V
CR1 9965 100 04879 10μF 20% 10V
f
RD1 9965 000 39986 CFR 10Ω 1/4W
RD2 9965 000 40003 CFR 2.7kΩ
RD3 9965 000 39987 CFR 100Ω
RD4 9965 000 40489 CFR 18kΩ 1W
RD5 9965 000 39989 CFR 10kΩ 1/4W
RR1 9965 000 39986 CFR 10Ω 1/4W
b
LED 9965 000 40273 LED 3.1mm red
d
D001 9965 000 40221 Zener 5V1 1/2W 5%
M001 9965 100 05378 IR Rec. HS0038B 38KHz
EN 54 11. SK5.0L CA Revision List