Professional Documents
Culture Documents
Service Guide
1
Service Guide Version and Revision
2
Copyright
Copyright © 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties
of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is
sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer
Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the software.
Trademarks
Acer is a registered trademark of Acer Incorporated.
All other trademarks are property of their respective owners.
Conventions
The following conventions are used in this manual:
3
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided
for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness,
your regional office may have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra
memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such
cases, please contact your regional offices or the responsible personnel/channel to provide you with further
technical details.
2. Please note WHEN ORDERING FRU PARTS,you should check the most up-to-date information available on
your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the
printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list
provided by your regional Acer office to order FRU parts for repair and service of customer machines.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to
this equipment. It is the responsibility of the user to correct such interference.
As ENERGY STAR® Partner our company has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
Warning:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are
present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
4
Precautions
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or
in a wet basement.
Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and
cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold
with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the manufacturer
and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable
operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered.
Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator
or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of
the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter (Output 12Vdc), which has UL, CSA listed license.
The following symptoms are normal with LCD monitor and do not indicate a problem.
Notes
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and
then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a
missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,
when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image
or turning off the Power Switch for hours.
5
Table Of Contents
Introduction ……………………………………… 7
Electrical Requirements ……………………………………… 8
LCD Monitor General Specification ……………………………………… 9
LCD Panel Specification ……………………………………… 10
Support Timing ……………………………………… 11
Block Diagram ……………………………………… 12
Main Board Diagram ……………………………………… 13
Software Flow chart ……………………………………… 14
Main Board Layout ……………………………………… 16
Front Bezel ……………………………………… 17
Rear Bezel ……………………………………… 18
6
Monitor Features Chapter 1
Introduction
Scope
This specification defines the requirements for the 20” MICROPROCESSOR based Multi-mode supported high
resolution color LCD monitor. This monitor can be directly connected to general 15 pin D-sub VGA connector and 24
pin DVI connector. It also supports VESA DPMS power management and plug & play function. There is a build-in
stereo audio amplifier with OSD control to drive a pair of speakers.
Description
The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no
radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop
space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF
target is 50k hours or more.
Chart of AL2051W
D-SUB
Signal Interface
DVI
DDC DDC2B
Speaker Yes
Microphone Jack No
7
Electrical Requirements
Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified.
Measurement systems
The units of measure stated in this document are listed below:
1 gamma = 1 nano tesla
1 tesla = 10,000 gauss
cm = in x 2.54
Lb = kg x 2.2
Degrees F = [°C x 1.8] + 32
Degrees C = [°F - 32]/1.8
u' = 4x/(-2x + 12y + 3)
v' = 9y/(-2x + 12y + 3)
x = (27u'/4)/[(9u'/2) - 12v' + 9]
y = (3v')/[(9u'/2) - 12v' + 9]
nits = cd/(m2) = Ft-L x 3.426
lux = foot-candle x 10.76
8
LCD Monitor General Specification
M201EW01.
Digital interface
DVI-D 24pin
9
LCD Panel Specification
LCD Panel Model (AU M201EW01)
Display Type active matrix color TFT LCD
Resolution 1680 x 1050
Display Dot 1680(x3) x 1050
Display Area 433.44mm(H) x 270.90mm(V)
Pixel Pitch 0.258mm(H) x 0.258mm(V)
Display Color 16.7M (true)
Lamp Frequency 50kHz(Max.)
Lamp Current 6.0 mArms (typ)
Weight 2950g (typ)
Optical Specifications
The optical characteristics are measured under stable conditions at 25℃:
10
Supported Timing
Support Modes
There will be 20 total support modes to accommodate the above mode and other video modes within the frequency
range of the monitor.
11
Monitor Block Diagram
The LCD monitor will contain a main board, a power board, which house the flat panel control logic, brightness
control logic and DDC.
The Inverter board will drive the backlight of panel.
AC-IN
Host Computer Video signal, DDC
100V-240
12
Main Board Diagram
Panel connector
(CN407)
OSD Control
KEY PAD
MST9251A-LF-205
MCU (Include: ADC, OSD etc) Frame
W79E632 (U401) Memory
(U402) (U303)
EEPROM
D-Sub Connector DVI Connector
AT24C16AN-10SU-2.7
(CN101) (CN102)
(U403)
DB15_SDA DVI_SDA
DB15_SCL DVI_SCL
EEPROM EEPROM
M24C02-WMN6TP M24C02-WMN6TP
(U101) (U102)
13
Software Flow Chart
Y
2 3
N
N
5
N
7 8
Y
N
10 11
N N
12 13
Y Y
N
14 15 16
17
N
18 19
14
Remark:
1) MCU initializes.
12) Check the analog port, are there any signals coming?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the
message disappears.
15
Main Board Layout
16
Front Bezel
External Controls
17
Rear Bezel
18
Operating Instructions Chapter 2
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will light up.
External Controls
19
Front Panel Control
• Power Button:
Press this button to turn the monitor ON or OFF, and display the monitor’s state.
• Menu / Enter:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD
menu when in Volume Adjust OSD status.
• <Volume:
Activates the volume control when the OSD is OFF or navigates through adjustment icons when OSD is ON or
adjust a function when function is activated.
• >/Volume:
Activates the volume control when the OSD is OFF or navigates through adjustment icons when OSD is ON or
adjusts a function when function is activated.
• Power Indicator:
Blue — Power On mode.
Orange —Power Off mode
NOTES
Notes
• Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to
direct sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your
monitor.
• For maximum protection, repackage your monitor as it was originally packed at the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a
cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor
before cleaning it.
20
Adjusting the Picture
a. How to Adjust a Setting
1. Press the MENU-button to activate the OSD window.
2. Press <or >to select the desired function.
3. Press the MENU-button to select the function that you want to adjust.
4. Press < or >to change the settings of the current function.
5. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4.
21
b. The Description For Control Function
22
23
Hot-Key Menu
a. Outline
OSD Message
a. Outline
Item Description
Auto Config When Analog signal input, if User Press Hot-Key “Auto”, will show this message, and the
Please Wait monitor do the auto config function.
Input Not When the Hsync Frequency, Vsync Frequency or Resolution is out of the monitor
Supported support range, will show this message. This message will be flying.
Cable Not Analog-Only Model: When the video cable is not connected, will show this message.
Connected This message will be flying.
Analog-Only Model: When the video cable is connected, but there is no active signal
No Signal
input, will show this message, then enter power saving.
24
Logo
When the monitor is power on, the LOGO will be showed in the center, and disappear slowly.
The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over
the DDC2B channel.
This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to
operate properly, there must be a video input signal.
This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA)
and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no
video-input signal present. When there is no video input signals this monitor, following a time-out period, will
automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the
video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is
similar to a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or clicking
the mouse restores the display.
25
Machine Disassembly Chapter 3
This chapter contains step-by-step procedures on how to assemble the monitor for
maintenance.
Disassembly Procedure
26
1. Remove two screws. (Fig 1)
2. Remove the hinge cover. (Fig 2)
3. Remove the one screw. (Fig 3)
Fig 1
Fig 2
Fig 3
27
4. Firstly, find out the two hooks position. (Fig 4)
5. Then, pry the rear cover up as arrowhead direction. (Fig 5)
6. Remove the six screws. (Fig 6)
Fig 4
Fig 5
Fig 6
28
7. Disconnect the wire harnesses of main board and panel, main board and power board. (Fig 7)
8. Remove four screws. (Fig 8)
9. Pry the main frame on the left to remove bezel. (Fig 9.1)
Pry the main frame on the right to remove bezel. (Fig 9.2)
Fig 7
Fig 8
Fig 9.1
29
Fig 9.2
10. Remove the screws for frame on the left. (Fig 10.1)
Remove the screws for frame on the right. (Fig 10.2)
Fig 10.1
Fig 10.2
30
11. Disconnect the wire harness for power board and lamps. (Fig 11)
12. Remove the four screws to remove the main board. (Fig 12)
13. Remove the eight screws to remove BKT base. (Fig 13)
Fig 11
Fig 12
Fig 13
31
14. Remove the two screws to loose the copper manganese wire. (Fig 14)
15. Remove the four screws and disconnect the wire harness. (Fig 15)
16. Remove the four screws. (Fig 16)
Fig 14
Fig 15
Fig 16
32
17. Turn the six clips anticlockwise to remove the shielding. (Fig 17)
18. Disconnect the wire harness of main board and panel. (Fig 18) The end!!
Fig 17
Fig 18
33
Troubleshooting Chapter 4
This chapter provides troubleshooting information for the AL2051W:
1. Main board
No power
No power
NG
NG
OK Replace X401, X402
Replace U402
NG
Replace U401
34
No picture (LED orange)
No picture
OK
OK
Check reset circuit of NG Check Correspondent
U402 is normal component
Measure U703 PIN2=1.8V
U705 PIN2=3.3V OK
Replace U402
OK
X402 oscillate NG
waveform is normal
Replace U703, U705
NG
OK
Replace X402
NG
OK Check Correspondent
component
Replace U401
35
White screen
White screen
NG
Measure Q701 base X401 oscillate
is high level? waveform is normal
OK NG Replace X401
OK
NG Check Correspondent
Check Correspondent NG
component.
component.
OK
OK
Replace U402
Replace Panel
36
2. Power Board
No power
No power
NG
OK Check AC line
OK NG
Check F901, bridge rectified circuit
OK NG
Check R903, R904,IC901
OK
NG Check Q902,Q903
Check T901, D902
37
3. Inverter Board
No backlight
Check L805 =12V
NG
OK
Check adapter board
NG
OK
Check Q802,Q804,ZD803 circuit
OK NG
Check R821,C821
OK NG
Check feedback
38
Keypad Board
N
Is Keypad Board connecting normally? Connect Keypad Board
Y
N
Is Button Switch normally? Replace Button Switch
N
Is Keypad Board Normally? Replace Keypad Board
39
Connector Information Chapter 5
The following figure shows the connector locations on the monitor:
1 5
6 10
11 15
40
FRU (Field Replaceable Unit) List Chapter 6
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of AL2051W.Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
NOTE: Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information
available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part number
change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of
this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order
FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on
how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.
41
Exploded Diagram (Model: AL2051W)
42
Part List
Above picture show the description of the following component.
Item Picture Description Part No.
2 BEZEL 34G1782AQW B
43
5 SHIELDING 85G 732 1
6 PANEL 750GLUA1W1211N
44
10 SPEAKERS 78G 322 3B
11 BASE 34G1785 QW B
45
Schematic Diagram Chapter 7
Main Board
MST9251A B2
SCHEMATIC
B1
RIN RIN +3.3DV1
GNDR GNDR +3.3DV2
TXD GIN GIN AVDDPLL2
RXD GNDG GNDG AVDDPLL
DDC_CLK SOG SOG AVDDA
DDC_DAT BIN BIN AVDD_DVI
DDC_WP GNDB GNDB +APLL
ST_DET1 HSYNC HSYNC VDDC
ST_DET2 VSYNC VSYNC VDD_MPLL
VLCD
R+ R+
R- R-
G+ G+
G- G- VLCD
B+ B+
B- B- VDD_MPLL
CLK+ CLK+ VDDC
CLK- CLK- +APLL
AVDD_DVI
AVDDA
3.INPUT
B3 AVDD_PLL
AVDDPLL2
ST_DET2
ST_DET1 +3.3DV2 +2.5MVDD
DDC_WP ALE ALE +3.3DV1
DDC_CLK RD RD
DDC_DAT WR WR +2.5MVDD
VCPU RXD HWRESET HWRESET
TXD INT INT
VDDC
+2.5V_DMC +2.5V_DMQ+2.5MVDD VDD_MPLL
+2.5MVDD
+2.5V_DMQ Title
+2.5V_DMC
715G1765-1 for AL2051W (acer)
Size Document Number Rev
2.POWER 4.SCALER B TOP 1
Date: Tuesday, January 03, 2006 Sheet 2 of 8
46
VCC5V VCC5V VCC12V VCC5V VLCD VCC5V
L701A1 09/27 Modified by SC
VLCD 5
NC
VCC12V
R702 R703 R704 C771
L701
R717
R705
C710綼 U701 U701 22uH 10K 1/16W NC 10K 1/16W 0.1uF/16V
1 8 D R707
S D VCPU
2 7 FB701 600 OHM R708 51K 1/16W Q701
3 S D 6 D704 D705 G AO3401 NC
S D VCPU 7 S
C710 4 5 SBM84PT SBM84PT C773
0 1/16W
0 1/16W
+ + + +
C
1uF/25V G D C706 C707 C708 C709 1000pF R709 4.7K 1/16W C772
0805 220uF/16V 220uF/16V 220uF/16V 220uF/16V 0805 B Q702
AM4811P-T1-PF 7 onPanel_5V/3.3V
C702 (NC)0.1uF/16V
PMBS3904
VCC12V C704 (NC)1uF/16V
E
D125 R710
0.1uF + C703
R719 C711 100uF/16V 10K 1/16W
CN701 LP701 62K 1/10W 1% 1000pF LL5232B 5.6V 5%
U707 0805 0805
1+12V_IN 6 3 8 1
7 VIN ISENSE 2
5 2 6 PGATE GND 3
+ + R721 5 PWRGND NC 4
2
R724
R725
10K 1/16W 10K 1/16W 0.1uF/16V
D
VCC12V_AUDIO R726 51K 1/16W 706
VCC12V FB702 120 OHM FB703 120 OHM G AO3401
S
0 1/16W
0 1/16W
C
MH1 MH4 MH5 MH6 R727 4.7K 1/16W C777
VCC12V_AUDIO 8
B Q705
7 onPOWER
FB704 600 OHM (NC)0.1uF/16V
PMBS3904
1
C775
E
D706 R728
0.1uF + C778
NC 100uF/16V 10K 1/16W
VCC12V
VCC5V
C713 + C714
Change to CN702
0.1uF/16V
6 10K 1/16W
U702 +3.3AVDD +3.3AVDD for 5
3 2 4 ON_OFF R712 4.7K 1/16W
Vin Vo2 4 AVDD_DVI 3 VCC5V
Vo2 2
pin4,pin10
C
ADJ
E
0.1uF 47uF/16V 0.1uF C722 C723 C724 R715 C
+
B E
10uF/50V 0.1uF 0.1uF Q704
C
1K 1/16W R716
+3.3DVDD + C716 B
TO-263 VCPU 22uF/16V
AdjBACKLITE 5
VCC5V+ +3.3DVDD PMBS3904 1K 1/16W
U705 +3.3AVDD for
E
AIC1084-33M AVDD_PLL C
3 2 AVDD_PLL +3.3AVDD
VIN VOUT 4 FB705 NC L715 B E
1
ADJ
VOUT AVDD_PLL 5
120 OHM
Change to AZ1084-18 +2.5VM
C731 C730 + C732 L704 120 OHM
C733 +
pin12
C734 TO263
U703
VCC5V+ +2.5MVDD
0.1uF 47uF/16V 0.1uF 10uF/50V +1.8V_VDD U704 L703
0.1uF
3 2 3 2
GND
Vin Vout 4 VI VO 4 120 OHM
Vout C720 + C726 VO C721 + C727
GND
+3.3AVDD for PLL_GND C728 C725 + C729
47uF/25V 0.1uF 0.1uF
1
AVDDA 0.1uF AP1084D18 47uF/16V 0.1uF 47uF/25V
+3.3AVDD L706 AVDDApin17,pin34
1
AVDDA 5
120 OHM
+3.3DVDD C749 + C750 C751
10uF/50V
L707 +3.3DV1 1.8V for pin86, pin102,pin113
pin162,pin182 0.1uF 0.1uF +2.5MVDD
VDDC ,pin125,pin139,pin154
+3.3DV1 5 pin63,pin79,pin131,
120 OHM + C753 C754 C755
pin156,pin173,pin185,pin195 +2.5MVDD
10uF/50V +1.8V_VDD L705 VDDC
0.1uF 0.1uF 3.3V(6251) for +2.5MVDD 5
AVDD_PLL2 120 OHM
VDDC 5
+ C736 C737 C738 C739 C740 C741 C742 C743 C744 C745 C746 C747 C748
AVDDPLL2 pin109 Audio PLL C735
+3.3AVDD 10uF/50V
1.8V 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
AVDDPLL2 5
L710 120 OHM
+3.3DVDD C758 + C759 +1.8V_VDD +APLL
L711 +3.3DV2 10uF/50V
pin66 +APLL 5
0.1uF L708 120 OHM
+3.3DV2 5
+ C756 C757
120 OHM
C760
+ C762
PLL_GND
pin49
10uF/50V 0.1uF
Change to
+3.3V for TO-252
VDD_MPLL 2.5V
10uF/50V 0.1uF
FOR
+3.3AVDD PLL_GND VCC5V+ L712 DDR
L713 VDD_MPLL pin204 U706 +2.5V_DMC
3 2
Vin Vo2 +2.5V_DMC 6
4 120 OHM
VDD_MPLL 5 Vo2
120 OHM C763 + C766 +
Remove C94/C95/U13 C765 + C769 ADJ C764 C767 C768
10uF/50V 47uF/25V 0.1uF 47uF/25V 0.1uF 0.1uF
+3.3DV1=>LCD I/F Pad AIC1084-33PE
0.1uF L714
1
47
RXD 7
DB15
TXD 7
11 1 FB101 0 1/16W R102 100 1/16W C102 0.047uF
RIN 5
6
12 2 FB102 0 1/16W R103 100 1/16W C103 0.047uF
GIN 5
7
13 3 FB103 0 1/16W R104 100 1/16W C104 0.047uF
BIN 5
8
470 1/16W C105 0.001uF
75 1/16W
75 1/16W
14 4 R105
SOG 5
R106
R107
9 PC5V R101 C101 C106 C107
15 5 VGA_CON
10 75 1/16W NC NC NC
17
16
TZMC5V6-GS08
TZMC5V6-GS08 CN101 R109 100 1/16W C109 0.047uF
GNDG 5
R110 100 1/16W C110 0.047uF
GNDB 5
3
D103 D104 D105
BAV99 BAV99 BAV99 VCC5V
VCC5V
C111 C112 C113 R111
10K 1/16W
1
0.1uF 0.1uF 0.1uF
1
HSI FB104 150 OHM R113 1K 1/16W
HSYNC 5
3
TZMC5V6-GS08 TZMC5V6-GS08 TZMC5V6-GS08
2.2K 1/16W 33pF 10K 1/16W 220pF R118 R119 R120 C116
10K 1/16W U101
10K 1/16W 4.7K 1/16W 8 1 0.1uF
7 VCC A0 2
CLK_DDC R121 100 1/16W 6 WP A1 3
DAT_DDC R122 100 1/16W 5 SCL A2 4
SDA GND
VCC5V D110 M24C02WMN6
CN102 TZMC5V6-GS08 D111
TZMC5V6-GS08
7 DDC_DAT
25 R123
R 7 DDC_CLK
26
G 27 10K 1/16W VCC5V DVI5V
B 29
RGB GND
1
28
HSYNC 8
VSYNC 15 R124 100 1/16W
SYNC GND ST_DET2 7
6 CLK_DDC2 R125 100 1/16W DVI5V D112
DDC SCL 7 DAT_DDC2 R126 100 1/16W R127 BAV70
DDC SDA 14 10K 1/16W
+5V 16
HPD
3
11
1/3shield 3 R128 D113 D114 D115 D116 C117 R129 R130 C118
2/4shield 19 LL5232B 5.6V 5% LL5232B 5.6V 5% LL5232B 5.6V 5% LL5232B 5.6V 5% 10K 1/16W U102
0/5shield 22 NC 0.1uF 10K 1/16W 8 1 0.1uF
clk shield R131 4.7K 1/16W 7 VCC A0 2
18 R132 10 1/16W 6 WP A1 3
DAT0+ B+ 5 SCL A2
17 R133 10 1/16W 5 4
DAT0- B- 5 SDA GND
10 R134 10 1/16W
DAT1+ G+ 5
9 R135 10 1/16W M24C02WMN6
DAT1- G- 5
2 R136 10 1/16W
DAT2+ R+ 5
1 R137 10 1/16W
DAT2- R- 5
13
DAT3+ 12
DAT3- 5 R138
DAT4+ DDC_WP 7
4
DAT4- 21 NC
DAT5+ 20
DAT5- 23 R139 10 1/16W
clk+ CLK+ 5
24
clk- CLK- 5
R140 10 1/16W
31
32
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 715G1765-1 for AL2051W(acer)
Size Document Number Rev
B INPUT 1
Date: Tuesday, January 03, 2006 Sheet 4 of 8
48
CONNECTOR for PANEL
CN407
2 1
4 3
GND TXA0- 6 5 TXA0+ GND
TXA1- 8 7 TXA1+
TXA2- 10 9 TXA2+
+3.3DV1 AVDD_PLL TXAC- 12 11 TXAC+
TXA3- 14 13 TXA3+
3 AVDD_PLL TXB0- TXB0+
AVDDPLL2 16 15
VDD_MPLL +APLL TXB1- 18 17 TXB1+
For AOC LCD I/F- TXB2- 20 19 TXB2+
3 VDD_MPLL +3.3DV1 3 AVDDPLL2 3 TXBC- TXBC+
+3.3DV2 22 21
AVDD_DVI
3 +APLL F/W default set Odd/Even Swap. TXB3- 24 23 TXB3+
3 +3.3DV2
3 AVDD_DVI
+2.5MVDD VDDC 4/13/93 26 25
28 27
3 +2.5MVDD VDDC 3
AVDDA 30 29
3 AVDDA
GND
204
162
182
102
113
125
139
154
109
131
156
173
185
195
199
198
197
196
193
192
191
190
189
188
U401 VLCD CONN GND
17
34
10
66
86
49
12
63
79
4
(5mm)
AVDD_APLL
AVDD_PLL
VDDP
VDDP
VDDP
AVDD_PLL2
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
AVDD_MPLL
VDDM
VDDM
VDDM
VDDM
VDDM
VDDM
VDDC
VDDC
VDDC
VDDC
VDDC
VDDC
VDDC
AVDD_DVI
AVDD_DVI
AVDD_ADC
AVDD_ADC
3 VLCD
DVI INPUT 187 TXA0-
120 OHM
360 1/10W
360 1/10W
360 1/10W
360 1/10W
360 1/10W
LVB0M
R445
R446
R447
R465
R466
RX2+ 207 186 TXA0+ L404 + C425
4 R+ RX2- DVI_R+ LVB0P TXA1-
208 181
4 R- RX1+ DVI_R- LVB1M
2 180 TXA1+ C424 0.1uF
4 G+ RX1- DVI_G+ LVB1P
3 179 TXA2- 22uF/50V
4 G- RX0+ DVI_G- LVB2M
5 178 TXA2+
4 B+ RX0- DVI_B+ LVB2P
6 177 TXAC-
4 B- RXC+ DVI_B- LVBCKM
8 176 TXAC+
4 CLK+ DVI_CK+ LVBCKP
RXC- 9 175 TXA3-
4 CLK- DVI_CK- LVB3M
11 174 TXA3+
AVDD_DVI REXT LVB3P TXB0-
R444 14 171
390 1/16W 15 DDCD_DA LVA0M 170 TXB0+
DDCD_CK LVA0P 169 TXB1-
18 LVA1M 168 TXB1+
19 HSYNC1 LVA1P 167 TXB2-
20 VSYNC1 LVA2M 166 TXB2+
21 BIN1 LVA2P 165 TXBC-
22 BIN1M LVACKM 164 TXBC+
SOGIN1 LVACKP
VGA INPUT
23 161 TXB3-
24 GIN1 LVA3M 160 TXB3+
25 GIN1M LVA3P
26 RIN1 FSDATAU[0..31]
RIN1M FSDATAU[0..31] 6
153
DQS[0] FSDQSU0 6
27 152 FSDATAU0
4 GNDB BIN0M MDATA[0]
28 151 FSDATAU1
4 BIN BIN0 MDATA[1]
29 150 FSDATAU2
4 GNDG GIN0M MDATA[2]
30 149 FSDATAU3
4 GIN GIN0 MDATA[3]
31 148 FSDATAU4
4
4
4
SOG
GNDR
RIN
32
33
SOGIN0
RIN0M MST9251A(208Pin) MDATA[4]
MDATA[5]
147
146
FSDATAU5
FSDATAU6
36 RIN0 MDATA[6] 145 FSDATAU7
4 HSYNC HSYNC0 MDATA[7]
37 144 FSDATAU8
4 VSYNC VSYNC0 MDATA[8]
38 143 FSDATAU9
C427 0.1uF 39 RMID MDATA[9] 142 FSDATAU10
40 REFP MDATA[10] 141 FSDATAU11
0.1uF REFM MDATA[11] 138 FSDATAU12
C428 MDATA[12] 137 FSDATAU13
41 MDATA[13] 136 FSDATAU14
42 VI_DATA[8] MDATA[14] 135 FSDATAU15
43 VI_DATA[9] MDATA[15] 134
VI_DATA[10] DQS[1] FSDQSU1 6
44 133 FSDQM0U R448 33 1/16W
VI_DATA[11] DQM[0] FSDQM0 6
45 101 FSDQM1U R449 33 1/16W
VI_DATA[12] DQM[1] FSDQM1 6
46 100
VI_DATA[13] DQS[2] FSDQSU2 6
47 99 FSDATAU16
48 VI_DATA[14] MDATA[16] 98 FSDATAU17
51 VI_DATA[15] MDATA[17] 97 FSDATAU18
52 GPIO[5]/VHS MDATA[18] 96 FSDATAU19
53 GPIO[4]/VCLK2 MDATA[19] 95 FSDATAU20
54 VI_CK MDATA[20] 94 FSDATAU21
55 VI_DATA[0] MDATA[21] 93 FSDATAU22
56 VI_DATA[1] MDATA[22] 92 FSDATAU23
57 VI_DATA[2] MDATA[23] 91 FSDATAU24
58 VI_DATA[3] MDATA[24] 90 FSDATAU25
59 VI_DATA[4] MDATA[25] 89 FSDATAU26
60 VI_DATA[5] MDATA[26] 88 FSDATAU27
61 VI_DATA[6] MDATA[27] 85 FSDATAU28
77 VI_DATA[7] MDATA[28] 84 FSDATAU29
GPIO[2]/VVS MDATA[29] 83 FSDATAU30
HWRESET R442 100 1/16W 67 MDATA[30] 82 FSDATAU31
INT 68 HWRESET MDATA[31] 81
ALE INT DQS[3] FSADDR11 FSDQSU3 6
69 130
R443 C421 RD 70 ALE MADR[11] 129 FSADDR10 FSADDR[0..11]
RDZ MADR[10] FSADDR[0..11] 6
10K 1/16W WR 71 128 FSADDR9
0.1uF AD0 72 WRZ MADR[9] 127 FSADDR8
MCU INTERFACE
22pF C419
Unloaded trace impedance on this interface is 90 Ohm
103
108
114
126
132
140
155
157
159
163
172
183
184
194
205
206
13
16
35
50
64
65
80
87
1
7
+2.5MVDD
Loaded trace impedace with DRAM load is 65 Ohm (for 2.5 inch total trace
length)
R450
MVref
R451
1K 1/16W C422 C423
0.1uF 0.001uF
Title
715G1765-1 for AL2051W (acer)
Size Document Number Rev
C Scaler (MST9251A) 1
Date: Tuesday, January 03, 2006 Sheet 5 of 8
49
+2.5V_DMQ +2.5V_DMC
+ C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 + C317 C318 C319 C320 C321 C322 C323 C324 C325
22uF/50V 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 22uF/50V 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
M12
D11
H10
D10
B11
E10
K10
F10
J10
FSDATA[0..31]
D2
H3
C6
C7
D3
B2
B4
B6
B7
B9
E3
K3
K6
K7
F3
J3
U303
VREF
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
RN301 33 1/16W
5 FSADDR[0..11] FSADDR0 FSDATA16
M4 A6 FSDATA24 8 1 FSDATAU24
FSADDR1 M5 A0 DQ0 B5 FSDATA17 FSDATA25 7 2 FSDATAU25
FSADDR2 L5 A1 DQ1 A5 FSDATA18 FSDATA26 6 3 FSDATAU26
FSCLK+ FSADDR3 A2 DQ2 FSDATA19 FSDATAU[0..31] 5
M6 A4 FSDATA27 5 4 FSDATAU27
FSADDR4 M7 A3 DQ3 B1 FSDATA20
R311 FSADDR5 L8 A4 DQ4 C2 FSDATA21 RN302 33 1/16W
150 1/16W 1% FSADDR6
FSADDR7
M8
M9
A5
A6
A7
DQ5
DQ6
DQ7
C1
D1
FSDATA22
FSDATA23 2 FSDATA28
FSDATA29
8
7
1
2
FSDATAU28
FSDATAU29
FSDATAU0
FSDATAU1
FSCLK- FSADDR8 M10 FSDATA30 6 3 FSDATAU30 FSDATAU2
FSADDR9 L7 A8/AP J12 FSDATA0 FSDATA31 5 4 FSDATAU31 FSDATAU3
Place this parallel termination close to FSADDR10 K5 A9 DQ8 J11 FSDATA1 FSDATAU4
corresponding memory IC Pins FSADDR11 L6 A10 DQ9 H12 FSDATA2 RN303 33 1/16W FSDATAU5
A11 DQ10 H11 FSDATA3 FSDATA8 8 1 FSDATAU8 FSDATAU6
DQ11 F12 FSDATA4 FSDATA9 7 2 FSDATAU9 FSDATAU7
5
5
FSBKSEL0
FSBKSEL1
FSBKSEL0
FSBKSEL1
M3
L4 BA0
BA1
DQ12
DQ13
DQ14
F11
E12
FSDATA5
FSDATA6 0 FSDATA10
FSDATA11
6
5
3
4
FSDATAU10
FSDATAU11 FSDATAU8
E11 FSDATA7 FSDATAU9
FSCLK- L11 DQ15 RN304 33 1/16W FSDATAU10
5 FSCLK- FSCLK+ CK# FSDATA12
L10 E2 FSDATA24 8 1 FSDATAU12 FSDATAU11
5 FSCLK+ FSCKE CK DQ16 FSDATA13
M11 E1 FSDATA25 7 2 FSDATAU13 FSDATAU12
5 FSCKE CKE DQ17 FSDATA14
M1 F2 FSDATA26 6 3 FSDATAU14 FSDATAU13
/FSRAS L1 CS# DQ18 F1 FSDATA27 FSDATA15 5 4 FSDATAU15 FSDATAU14
LAYOUT Joyce request
5 /FSCAS
5
5
/FSRAS
/FSWE
/FSCAS
/FSWE
K1
K2
RAS#
CAS#
WE#
DQ19
DQ20
DQ21
H2
H1
FSDATA28
FSDATA29
3 RN305 33 1/16W
FSDATAU15
R310 C316
10K 1/16W
0.1uF GND
G5
G6
G7
G8
D4
D6
D7
D9
H5
H6
H7
H8
E5
E6
E7
E8
K4
K9
F5
F6
F7
F8
J5
J6
J7
J8
EM6A9320BI-5M
50
VCPU
3 VCPU
10K 1/16WR452
10K 1/16WR453
10K 1/16WR454
10K 1/16WR455
5
6
7
8
5
6
7
8
RP401
R464 C431 RP402
10K 1/16W
0.1uF 10K 1/16W
10K 1/16W
U402
4
3
2
1
4
3
2
1
C432 22pF
44
X402 35 2
VCC
EA/VP P1.0 AD0 5
3
P1.1 AD1 5
21 4
X1 P1.2 AD2 5
+ C433 20MHz 5
10uF/16V P1.3 AD3 5
VCPU 6
20 P1.4 7
X2 P1.5 DDC_WP 4
U404 MAX810STR C434 22pF 8 R440
P1.6 RD 5
9
C
P1.7 WR 5
3 2 10 22K 1/16W
VCC RST RESET 24 B Q403
GND
E
R417 100 1/16W 16 INT1/P3.3 P2.3 28 LEFT C445
Reset
1
GND
P4.2 P4.0 RXD 4
R426 10K 1/16W Standby 12 34 LED_B
8 AUDIO_SD P4.3/ISP P4.1
R429 10K 1/16W Mute
8 AUDIO_MU
4 ST_DET1
22
MTV416/W79E632
4 ST_DET2
5 HWRESET
C437 C438
5 ALE
3 onPANEL_5V/3.3V
0.1uF 0.1uF
3 onBACKLITE
R437 R438
LED_B B Q401 Q402 B LED_O
4.7K 1/16W PMBS3906 PMBS3906 4.7K 1/16W
3
3
D404 D405 D406 D407 D408
LED_GRN LED_ORANGE BAV99 BAV99 BAV99 BAV99 BAV99
C
C
1
VCPU
DP1 SW401 SW402 SW403 SW404 SW405
3
D402
3
BAV99 D403 C443 C442 C441 C440 C439 LCD ONOFF KEY LEFT KEY AUTO KEY RIGHT KEY MENU
2
1
VCPU DUAL LED BAV99
3
C451
2
1000pF C452
1000pF
Title
715G1765-1 for AL2051W (acer)
Size Document Number Rev
B MCU 1
Date: Tuesday, January 03, 2006 Sheet 7 of 8
51
VCC12V_AUDIO
3 VCC12V_AUDIO
+ + C603
C601 C602 0.1uF
220uF/16V 220uF/16V
U601
TDA7496L
16
15
8
VS
VS
NC
CN602
4 R601 18K 1/16W C604 0.47uF/16V 4 17 C605 220uF/16V OUT_L
+
3 INL OUTL
2 R602 C606 0.47uF/16V 9 14 C607 220uF/16V OUT_R
+
1 INR OUTR
5 18K 1/16W 6 10
VOLUME SVR
11 7
7 AUDIO_SD STBY VAROUT_R
PHONEJACK
12 5
7 AUDIO_MU MUTE VAROUT_L
GND
GND
GND
GND
GND
GND
GND
+ R603 R604
C609 + C610 + C608
220uF/16V 1K 1/16W 1K 1/16W
13
18
19
20
20K 1/16W
1
2
3
R605
R606
C611 C612
100pF 100pF
R607
Volume 5
220K 1/16W
C613
0.1uF
CN603 CN601
1
5 1
4 2
3 R608 75 1/16W OUT_R 3
2 OUT_L 4
7 R609 75 1/16W
8
Title
715G1765-1 for AL2051W (acer)
Size Document Number Rev
A4 1
AUDIO
Date: Tuesday, January 03, 2006 Sheet 8 of 8
52
Power/Inverter board
53
C801 33pF/3KV CN801
D801
SB240 1
L805 C802 33pF/3KV 2
CN805 200uH 470uF/25V 3
1 C803 4
+
VIN FSI4502
C806 C804 33pF/3KV 5
2 Q801 4.7uF/1206 X5R
VIN C847 C848 R801 1 8
3 0.1uF/0805 0.1uF/0805 2.4K 0805 R802 ZD801 C805 S1N D1N CONN 33G8020-5D-U
ON/OFF 470 1206 5.6V 104/0805 2 7 6 7
4 Q802 R804 ZD802 G1N D1N C808
DIM DTA144WKA 10K 0805 R803 5.6V 3 6 C807 10pF/3KV
S2P D2P
2
5 L806 10K 085 4.7uF/1206 X5R
GND 1 4 5 2 1 R862 CN802
G2P D2P
3
6 200uH 1K 0805
GND
3
4.7uF/1206 X5R C810 C811 1
1 Q803 C809 2
3
33L8009-6N-H Q804 PMBS3904 SB240 D802 PT801 0.022uF/0805 X7R N.C D803
3
DTC144WKA 80LL17T-16 BAV99
1 R810 SB240 D804 R860 33G8021 2D U
2
ZD803 22 0805 C812 R863
2
R806 104/0805 0 0805 1K 0805
5.6V 10K 0805 1 8
2
C814 S1N D1N
0.1uF/0805 C815 2 7
1uF/0805 G1N D1N R807
2M 0805
2M 0805
C813 3 6
N.C
N.C
S2P D2P
3
1uF/25V D805 R809
1
R808
4 5 1N4148 L801 120K 1/8W
G2P D2P L802
R805 L
R813 22 0805 Q805 FSI4502 L
R811
R855
C816 22 0805 R812
0 0805
0.22uF/0805 R814
4
2M 0805
10 1206
SB240 D806
2
R856 0 0805
R815
R857
C818 IC801 C817 120K 1/8W
1.0uF/0805 0.047uF/0805
R818 R816 R861
C819 0 0805 1 20 C820 1K 0805
1uF/0805 CTIMR NDRV_B N.C 2M 0805
2 19 R817
Q806 R819 NC OVP PDRV_A R821 120K 1/8W
NC 3 18 C821 30K 0805 D807 N.C
R820 3 2 ENA CT 220PF/0805 R823
NC 4 17 620K 0805
SST RT
3
OZ1060
R822 9.1k 0805 R824 1M/ 0805 NC C823
1 5 16 220pF
C822 VDDA PWRGND C824 D808 1N4148
1
NC 7 14 C827
REF DIM
C825
1uF/0805 8 13 NC
C826 470pF
は layout
RT1 LPWM
3
C828 D809
9 12 0.047uF/0805 2
C829 FB PDRV_C Q808
0.0068uF/25V 10 11 RK7002 4148 D810
CMP NDRV_D R827 BAV99
R826 39K 0805 22 0805
1
R829 R830
R828 15K 0805 430 1% 0805
NC
R831 Q809
R867 39K NC R832
RK7002 NC
0 OHM
2
+
3
Q811 4
D821 C839 C832 AM4502 C833 2 1 C836 33pF/3KV 5
4148 0.01uF/0805 470uF/25V 4.7uF/1206 X5R C835
1M 0805 1 8 PT802 10pF/3KV
R836 S1N D1N 80LL17T-16 CONN 33G8020-5D-U
R835 N.C C837 2 7 C838
G1N D1N
3
104/0805 4.7uF/1206 X5R N.C
3 6 C840 C841
S2P D2P
82K 1/4W 4 5 0.022uF/0805 X7R D812 R865 CN804
G2P D2P BAV99 1K 0805
R839 R838 1
22 0805 SB240 D813 2
2
R864
C842 R840 1K 0805
1uF/0805 NC NC R859 33G8021 2D U
SB240 0 0805
D814
1 8
C843 S1N D1N
104/0805 2 7 R841
G1N D1N 2M 0805 R866
N.C
N.C
2
3
3 6 D815 R842 R843 1K 0805
S2P D2P
1
1N4148 L803 2M 0805
4 5 L804 120K 1/8W
G2P D2P L
L
R844
R845
R854
22 0805 Q812 R846
0 0805
FSI4502 R847
R853 0 0805
R858
2M 0805 120K 1/8W R848
2
SB240 D816 2M 0805
R850 R849
620K 0805 120K 1/8W
C844 D817 N.C
JP801 220pF
D818 1N4148
2 1
C845
470pF
3
D819
2
Q813
RK7002 4148 D820
BAV99
AOC (Top Victory) Electronics Co., Ltd.
1
R851 R852
15K 0805 430 1% 0805
Title
INPC2062AUA1P
Size Document Number Rev
Custom 2
Tuesday, January 03, 2006
Date: Sheet 2 of 3
54