Professional Documents
Culture Documents
Steps Of Job:
1. Use WEBLMT to login the eNodeB
Use the Ethernet cable to connect to ETH port of LMPT board.
Configure the IP 192.168.0.2 on laptop.
Use IE and visit the website:
http://192.168.0.49/
Username:admin
Password: admin123
DSP ETHPORT:SN=7,SBT=BASE_BOARD;
%%/*52789*/DSP ETHPORT:SN=7,SBT=BASE_BOARD;%%
RETCODE = 0 Operation succeeded.
DSP ETHPORT Result
Cabinet No. = 0
Subrack No. = 0
Slot No. = 7
Subboard Type = Base Board
Port No. = 0
Port Attribute = Fiber
Port Status = Up
Physical Layer Status = Up
Maximum Transmission Unit(byte) = 1500
ARP Proxy = Enable
Flow Control = Open
MAC Address = 707B-E8C5-5A80
Loopback Status = No Loop
In Loopback Mode or Not = No
Ethernet OAM 3AH Flag = Disable
Number of RX Packets(packet) = 34645
Number of RX Bytes(byte) = 4227324
Number of RX CRC Error Packets(packet) = 0
RX Traffic(byte/s) = 38
Number of TX Packets(packet) = 99806
Number of TX Bytes(byte) = 14221782
TX Traffic(byte/s) = 137
Local Configuration Negotiation Mode = Automatic Negotiation
Local Actual Negotiation Mode = Automatic Negotiation
Local Speed = 1000M
Local Duplex = Full Duplex
1/6
Peer Actual Negotiation Mode = Unknown
Peer Speed = 1000M
Peer Duplex = Unknown
Number of IPs = 2
IP Address List = 10.140.3.181 255.255.255.252
= 10.226.11.181 255.255.255.252
(Number of results = 1)
--- END
If you find wrong configuration, please use SET ETHPORT to modify as the picture below:
5. ADD DEVIP:
LST DEVIP:
LST DEVIP Result
LST DEVIP:;
O&M #1573
%%/*52894*/LST DEVIP:;%%
RETCODE = 0 Operation succeeded.
List Device IP Configuration Data
---------------------------------
Cabinet No. Subrack No. Slot No. Subboard Type Port Type Port No. IP Address Mask
0 0 7 Base Board Ethernet Port 0 10.20.2.3 255.255.255.0
0 0 7 Base Board Ethernet Port 0 10.20.3.11 255.255.255.0
0 0 7 Base Board Ethernet Port 0 10.20.4.69 255.255.255.0
(Number of results = 3)
--- END
ADD VLANMAP:
LST VLANMAP:
If you find wrong configuration, please use “RMV VLANMAP”to modify as the picture below:
2/6
ADD OMCH:
If you find wrong configuration, please use “RMV OMCH”to modify as the picture below:
PING:SN=7,SRCIP="10.20.3.11",DSTIP="172.168.3.1",CONTPING=DISABLE,APPTIF=NO;
Test01
PING 172.168.3.1: 32 data bytes
Reply from 172.168.3.1: bytes=32 Sequence=1 ttl=217 time=1 ms
Reply from 172.168.3.1: bytes=32 Sequence=2 ttl=217 time=1 ms
Reply from 172.168.3.1: bytes=32 Sequence=3 ttl=217 time=1 ms
Reply from 172.168.3.1: bytes=32 Sequence=4 ttl=217 time=1 ms
--- 172.168.3.1 ping statistics ---
4 packet(s) transmitted
4 packet(s) received
Percent 0.00 packet lost
round-trip min/avg/max = 1/1/1 ms
13 reports in total
--- END
Total: 13 packet(s) received.
DSP OMCH:
DSP OMCH Result:
DSP OMCH:FLAG=MASTER;
Test01
+++ HUAWEI 2012-04-05 17:53:39
O&M #1582
%%/*52944*/DSP OMCH:FLAG=MASTER;%%
RETCODE = 0 Operation succeeded.
3/6
Cabinet No. = 0
Subrack No. = 0
Slot No. = 7
Subboard Type = Base Board
Binding Route = No
Destination IP = NULL
Destination Mask = NULL
Route Type = NULL
Next Hop IP = NULL
Preference = NULL
OM Channel Status = Normal
Used State = In Use
(Number of results = 1)
--- END
3 Add the board and GPS information; Check the GPS Status and VSWR of the ports.
Run these commands as below:
RMV RRU: CN=0, SRN=60, SN=0;
RMV RRU: CN=0, SRN=61, SN=0;
RMV RRU: CN=0, SRN=62, SN=0;
RMV RRU: CN=0, SRN=63, SN=0;
RMV RRU: CN=0, SRN=64, SN=0;
RMV RRU: CN=0, SRN=65, SN=0;
RMV RRU: CN=0, SRN=66, SN=0;
RMV RRU: CN=0, SRN=67, SN=0;
RMV RRU: CN=0, SRN=68, SN=0;
RMV RRU: CN=0, SRN=69, SN=0;
RMV RRU: CN=0, SRN=70, SN=0;
RMV RRU: CN=0, SRN=71, SN=0;
RMV RRU: CN=0, SRN=72, SN=0;
RMV RRU: CN=0, SRN=73, SN=0;
RMV RRU: CN=0, SRN=74, SN=0;
RMV RRU: CN=0, SRN=75, SN=0;
RMV RRU: CN=0, SRN=76, SN=0;
RMV RRU: CN=0, SRN=77, SN=0;
ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RXNUM=4, TXNUM=4, RS=LO_TD, ALMPROCSW=ON;
ADD RRU: CN=0, SRN=61, SN=0, TP=TRUNK, RCN=1, PS=0, RT=MRRU, RXNUM=4, TXNUM=4, RS=LO_TD, ALMPROCSW=ON;
4/6
DSP GPS:; (Make sure the GPS Card State is Normal; And the GPS Satellites Traced is larger than 8.)
STR VSWRTEST:;(Make sure the VSWR result of RRU RF port connected is lower than 1500.)
5/6
6/6