Professional Documents
Culture Documents
1-27
MB32V001 - FRICTION
LOSS
Locating Non-Locating
Static
Frictional
Designation Bearing rating life Grease safety Power loss
moment
factor
Catalogue
SKF Explorer Basic SKF life Total
grease life
h Nmm W
* SKF rating life ( L10mh ) for steel-steel bearings; GBLM load based life ( L10GMh ) for hybrid bearings
Errors:
Warnings:
! Both : - Low viscosity ratio k, reduced asperity contact. It is recommended to select a higher viscosity lubricant or improve cooling. It is not
appropriate to look at basic rating life only. Instead use SKF rating life method. Recommended to use anti-wear (AW) or extreme pressure (EP)
additives to reduce wear
This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
2. Input
2.1. Bearing data
Designation Bearing type Principal dimensions Basic load ratings Fatigue load limit
Popular item d D B C C0 Pu
mm kN
Reference Limiting
nref nlim
r/min
This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
2.2. Loads & Speed
Coordinate Case
Load Coordinates Forces Speed
system weight
mm mm|deg mm kN kN kN r/min
LC1 F1 Cartesian 0.0 0.0 0.0 0.0 -0.141 0.0 3000.0 1.0
70.92
F2 Cartesian 0.0 0.0 0.0 36.18 0.0
5
2.3. Temperature
°C
LC1 70 65 70 65
- Maximum temperature is used for calculating the actual viscosity, kappa, aSKF and SKF rating life.
- Mean temperature is used for calculating bearing friction and power loss.
This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
2.4. Lubrication
Effective EP
Designation Lubricant Viscosity
additives
Designation Contamination
This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
3. Results
SKF Explorer
kN
Popular item Fr Fa Fr m
kN
Adjusted reference
Designation Adjustment factors
speed
r/min
Right 628/8-2Z
This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
Errors:
Viscosity
Designation Operating viscosity
ratio
Rated @ 40
SKF Explorer Actual Rated
°C
mm²/s
Catalogue
Designation Speed factor
grease life
h mm/min
Right 628/8-2Z
Errors:
This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
3.6. Bearing rating life
* SKF rating life ( L10mh ) for steel-steel bearings; GBLM load based life ( L10GMh ) for hybrid bearings
Warnings:
! Both : - Low viscosity ratio k, reduced asperity contact. It is recommended to select a higher viscosity lubricant or improve cooling. It is not
appropriate to look at basic rating life only. Instead use SKF rating life method. Recommended to use anti-wear (AW) or extreme pressure (EP)
additives to reduce wear
Power
Designation Frictional moment Friction sources
loss
At start
20-30°C
SKF Explorer Total Rolling Sliding Seals Drag loss
and zero
speed
Nmm W
This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
3.8. Bearing frequencies
Designation Rotational frequencies
SKF Explorer Inner ring Outer ring Rolling element set & cage Rolling element about its axis
Popular
fi fe fc fr
item
Hz
Hz
LIMITED WARRANTY : The SKF Bearing Select software tool of the SKF Company supports the calculation and selection of bearings.
This software is provided 'as is' with out any warranty of any sort, implicitly as well as explicitly.
Please note that the obtained results can be affected by many external parameters and/or the quality of the assumptions taken into account.
The results obtained using this software must be validated by the user who accepts the fact that the use of this software and the exploitation
of the obtained results are under the user's entire and sole responsibility.
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.