Professional Documents
Culture Documents
Geolite Modifier 210 is a stabilizing Relative to Geolite Modifier 205, Key Features and Typical Benefits
additive whose technology can foams made using Geolite uses existing urethane raw materials
offer ways to fully eliminate or Modifier 210 should reduce provides stability for use at isocyanate
dramatically reduce the use of more ABA, be softer, possess index as low as 85
auxiliary blowing agents (ABAs) improved “hand”, and exhibit yields softer foam over previous
in many grades of conventional compression set improvements Geolite products, giving improved
processing
slabstock foam. over other additives and technolo-
often eliminates all ABAs
gies used to reduce consumption
Like our earlier Geolite products,
of ABAs. Geolite Modifier 210 also
good properties in most grades,
this technology is based on the comparable to conventional foam
allows the manufacture of foams
principle of lowering the hardness excellent processability of all currently
possessing greater air flow. available soft foam technologies
of foam by reducing isocyanate
Therefore, it may offer greater
index. This permits the use of useful with varied processing
processing latitude, depending on technologies, including mechanical
higher water and lower blowing
foaming equipment. A consequence cooling
agent levels to achieve desired
of this may be the need for slightly plant operational in one to two days
foam hardness.
higher concentrations of tin catalyst. can reduce amine and tin catalyst
The use of Geolite Modifier 210 levels
can facilitate the production of
numerous foam grades at very low
indices (down to about 85), while
Typical Physical Properties
maintaining acceptable physical
Physical Form Liquid
properties and processing latitude. Specific Gravity at 25°C 1.115
The addition of Geolite Modifier 210, Weight per Gallon at 25°C (77°F), lb (kg) 9.27 (4.20)
Foam Properties
Using Geolite Modifier 210 with low-index, high-water formulations typically yields foam with improved physical properties – near
those obtained in conventional, lower water, ABA-based systems. In certain cases, with mechanical cooling processes, for example,
this technology can lead to foams with vastly improved physical properties, including compression sets. Moreover, this technology
helps enable the production of soft, ABA-free foams of manydensities. Soft foams with densities ranging from less than 1.05 pcf (17
kg/m3) to greater than 2.5 pcf (40 kg/m3) have been produced using Geolite Modifier 210.
Several performance test formulated grades using this Geolite Modifier 210 technology are shown in the following table.
Density, pcf 1 1 1.25 1.25 1.25 1.25 1.5 1.5 1.5 1.5 1.8 1.8 1.8 1.8
IFD, 25% 15 20 15 20 25 30 15 20 25 30 15 20 25 30
GM-210, pphp 3.5 3.6 2.4 2.5 2.6 2.7 1.7 1.9 2.0 2.1 1.1 1.3 1.5 1.6
Index 85.0 93.0 85.0 93.0 99.0 105.0 85.0 93.0 99.0 105.0 85.0 93.0 99.0 105.0
MeCl2, pphp 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Water, total, pphp 6.65 6.30 5.12 4.92 4.76 4.63 4.17 4.03 3.92 3.83 3.41 3.31 3.24 3.18
% ABA Reduction 100 100 100 100 100 100 100 100 100 100 100 100 100 100
Product formulations are included as illustrative examples only. Momentive makes no representation or warranty of any kind with respect to any such formulations, including,
without limitation, concerning the efficacy or safety of any product manufactured using such formulations.
Emergency Service
Momentive Performance Materials maintains an around-the-clock emergency service for its products.
Location Emergency Service Provider Emergency Contact Number
DO NOT WAIT. Phone if in doubt. You will be referred to a specialist for advice.
Worldwide
4information@momentive.com
DISCLAIMER: THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS INC., MOMENTIVE PERFORMANCE MATERIALS USA INC.,
MOMENTIVE PERFORMANCE MATERIALS ASIA PACIFIC PTE. LTD., MOMENTIVE PERFORMANCE MATERIALS WORLDWIDE INC., MOMENTIVE PERFORMANCE
MATERIALS GmbH, THEIR SUBSIDIARIES AND AFFILIATES DOING BUSINESS IN LOCAL JURISDICTIONS (collectively “SUPPLIERS”), ARE SOLD BY THE RESPECTIVE
LEGAL ENTITY OF THE SUPPLIER SUBJECT TO SUPPLIERS’ STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR
OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY
INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SUPPLIERS MAKE NO WARRANTY OR GUARANTEE, EXPRESS
OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY
OF ANY DESIGN INCORPORATING SUPPLIERS’ PRODUCTS, MATERIALS, SERVICES, RECOMMENDATIONS OR ADVICE. AFOREMENTIONED EXCLUSIONS OR
LIMITATION OF LIABILITY ARE NOT APPLICABLE TO THE EXTENT THAT THE END-USE CONDITIONS AND/OR INCORPORATION CONDITIONS CORRESPOND
TO THE RECOMMENDED CONDITIONS OF USE AND/OR OF INCORPORATION AS DESCRIBED BY SUPPLIER IN ITS PRODUCT DATA SHEET AND/OR PRODUCT
SPECIFICATIONS. EXCEPT AS PROVIDED IN SUPPLIERS’ STANDARD CONDITIONS OF SALE, SUPPLIERS AND THEIR REPRESENTATIVES SHALL IN NO EVENT BE
RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS OR SERVICES DESCRIBED HEREIN. Each user bears full responsibility
for making its own determination as to the suitability of Suppliers’ materials, services, recommendations, or advice for its own particular use. Each user must identify and
perform all tests and analyses necessary to assure that its finished parts incorporating Suppliers’ products, materials, or services will be safe and suitable for use under
end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of
Suppliers’ Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by Suppliers. No statement contained
herein concerning a possible or suggested use of any material, product, service or design is intended, or should be construed, to grant any license under any patent or other
intellectual property right of Suppliers or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product, service
or design in the infringement of any patent or other intellectual property right.
Momentive and the Momentive logo are trademarks of Momentive Performance Materials Inc.
Copyright 2003-2012 Momentive Performance Materials Inc. All rights reserved. MPM 121-021-60E-GL 06/12 Printed in U.S.A.
Page 4 of 4