Professional Documents
Culture Documents
MapsourceManual PDF
MapsourceManual PDF
mapping software
user’s manual
© Copyright 2004-2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc. Garmin (Europe) Ltd. Garmin Corporation
1200 E. 151st Street, Unit 5, The Quadrangle, No. 68, Jangshu 2nd Road,
Olathe, Kansas 66062 U.S.A. Abbey Park Industrial Estate, Shijr, Taipei County, Taiwan
Tel. 913/397.8200 or 800/800.1020 Romsey, SO51 9DL U.K. Tel. 886/2.2642.9199
Fax. 913/397.8282 Tel. 44/0870.8501241 Fax. 886/2.2642.9099
Fax. 44/0870.8501251
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted,
disseminated, downloaded, or stored in any storage medium for any purpose without prior written consent of Garmin. Garmin hereby
grants permission to download a single copy of this manual and of any revision to this manual onto a hard drive or other electronic
storage medium to be viewed, and to print one copy of this manual or any revision hereto, provided that such electronic or printed
copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial
distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and
to make changes in the content without obligation to notify any person or organization of such changes or improvements. Visit the
Garmin Web site (www.garmin.com) for current updates and supplemental information concerning the use and operation of this and
other Garmin products.
Garmin®, BlueChart®, City Select®, MapSource®, MetroGuide®, and iQue® are registered trademarks and Que™ is a trademark of
Garmin Ltd. or its subsidiaries, and may not be used without the express written permission of Garmin.
July 2005 Part Number 190-00417-20 Rev. C Printed in Taiwan
INTRODUCTION > TABLE OF CONTENTS
To unlock your product with a 25-Character 5. If you would like to register your product, you
Unlock Code: can do so at this time by clicking Yes, I have
NOTE: An Internet connection is required for the a new Registration Code. Enter the 7-digit
following procedure. registration code on the yellow piece of paper.
Click Next and follow the on-screen instructions
1. In MapSource, click Utilities > Unlock Maps. to register your product.
Then click Next.
If you would like to register your product later,
2. Click Yes, I have a 25-character unlock code. click No, I will register my product later and
Then click Next. click Next. You can now close the UnlockWizard
3. Click I have an Unlock certificate, I will type it and use MapSource.
in. Then click Next.
To unlock your product with an 8-character
Coupon Code:
NOTE: An Internet connection is required for the
following procedure.
1. In MapSource, click Utilities > Unlock Maps.
Then click Next.
2. Click No, I need to get a 25-character unlock
code. Then click Next.
UnlockWizard 3. Enter your personal information in the fields
provided and click Next.
4. Enter your 25-character unlock code and then a
comment, if desired. Click Next.
Connecting Your GPS Unit to a If your GPS unit came with a USB data
cable, connect your GPS to an available USB
Computer data port.
Install your MapSource software or run the installation
disk for your product before you connect your GPS
unit to your computer. If your MapSource product
came with a setup guide, follow those instructions to
learn how and when to connect your GPS unit to your USB Data Port
computer. You can also find this information in your
2. Verify that your GPS is turned on and the Serial
GPS unit owner’s manual.
Data Format is set to Garmin, if possible.
To connect your GPS unit to your computer: To verify proper connection to the
1. If your GPS unit came with a PC Interface computer:
Cable, connect your GPS to a serial 1. In MapSource, click Utilities > Get Unit ID.
communications port on your computer (see
2. Verify that the name of your GPS unit appears
illustration below).
in the Device field. If not, your GPS unit may
not be connected properly. Verify that the unit is
turned on, check the connection, and then click
Serial Communications Port
Find Device.
USING MAPSOURCE
Parts of MapSource
The MapSource window contains five main parts: the (1) toolbars, (2) data tabs, (3) splitter bar, (4) Graphic Map,
and (5) status bar.
2 3 4
5
MapSource User’s Manual 9
USING MAPSOURCE > LOADING MAPS TO YOUR GARMIN GPS UNIT
• Transfer the maps to your GPS unit. 2. Click the Map tool or click Tools > Map.
Move the mouse over the Graphic Map. Each
For help connecting your GPS unit to your computer, map region becomes outlined in yellow when
see page 8 or consult the owner’s manual for your you move over it with the mouse. The name and
GPS unit. To select maps and send them to your GPS size of the map region appear in the status bar.
unit, see the next two sections, “Selecting Maps” and 3. Click a map region to select it. To select several
“Transferring MapSource Data.” You may also be able map regions at once, click and drag the mouse
to view a tutorial on your MapSource installation disk over the areas you want to select. Selected map
about selecting and sending maps. regions are shaded pink.
Names of map
regions.
To select maps around waypoints, routes, For example, if you select both Topographical and
or tracks: Roads & Recreational data for the same geographical
Right-click a route, waypoint, or track in its area, you will not see a combination of topographic
Data tab and click Select Maps Around Route and road data. You will only see data from the Roads &
(Waypoint/Track) from the shortcut menu. Recreation data set. In order to see the Topographical
NOTE: Some MapSource products sell area maps data, turn the Roads & Recreational data off in your
separately. You can only select maps that you have GPS unit.
purchased and installed on your computer.
Transferring MapSource Data or tracks, you will not erase the maps on the card.
You can send map sets, waypoints, routes, and tracks to You can transfer waypoints, routes, and tracks from
your GPS unit or storage card, or you can receive data a data card to your GPS unit’s internal memory to
from your GPS unit or storage card. You may use one prevent them from being deleted from your data card.
of the following methods to transfer data to or from You cannot save maps from a data card to your GPS
your GPS unit (check your GPS unit owner’s manual to unit’s internal memory.
see what data transfer options are available):
• Serial or USB Cable
iQue® Users
To transfer data to and from an iQue, you may need to
• USB Data Card Programmer—You can use synchronize with your personal computer. You may not
this method if your GPS unit uses a Garmin be able to send or receive all types of data to/from your
data card (not preprogrammed). The USB Data iQue. For more information, refer to your iQue owner’s
Card Programmer works only with Windows 98, manual.
Windows 2000, Windows ME, or Windows XP.
• Compact Flash (CF) or Secure Digital (SD)
Card Reader—If your GPS unit uses a CF or
SD card, you can purchase a third-party card
reader to transfer data.
Each time you transfer maps to a data card, you
completely erase all data currently stored on the card
and replace it with new data. However, if you store
maps on a data card and you transfer waypoints, routes,
Sending Data to Your GPS Unit • If you are using a USB card programmer,
If your GPS unit has a storage card, verify that the card “USB Data Card Programmer” appears in
is inserted correctly into the unit. Also, connect your the Device field.
GPS unit to your computer and set your unit’s Data • If you are using a CF or SD card reader,
Transfer mode to Garmin, if applicable (see your unit select the correct drive letter from the
owner’s manual for instructions). Device field.
• If you are sending data to an iQue or cf
Types of data you can send are maps, waypoints, Que, select where you want to save data
routes, or tracks. Remember, you can only send maps under Map Storage Location. If necessary,
to an iQue. select the correct user name from the
Device fields.
NOTE: MapSource transfers all of the data listed
3. Under What to Send, check the boxes next to
in a data tab to your GPS unit each time you
each type of data you want to send.
transfer data.
4. Click Send. MapSource begins sending data to
To send data to a GPS unit or card reader: your GPS unit or card reader. After you begin
1. Select the data you want to send to your GPS transferring data, you can check the box next to
unit or card. The data appears in the correct tab Turn Off GPS After Transfer, if available.
on the left side of the window.
5. If you are using an iQue or cf Que, synchronize
2. Click Send To Device or click Transfer > with your personal computer, if necessary, so
Send To Device.... The name of your GPS unit that your unit receives the data.
or card reader should appear automatically in
the Device menu. If not, click Find Device.
Receiving Data from Your GPS Unit • If you are using a USB card programmer,
If your GPS unit has a storage card, verify that the card “USB Data Card Programmer” appears in
is inserted correctly into the unit. Also, connect your the Device field.
GPS unit or card reader to your computer and set your • If you are using a CF or SD card reader,
unit’s Data Transfer mode to Garmin, if applicable select the correct drive letter from the
(see your unit owner’s manual for instructions). Device field.
• If you are using an iQue, select the correct
To receive data from a GPS unit or card user name from the Device field.
reader: 3. Under What to Receive, check the boxes next
1. If you are using an iQue, synchronize with your to each type of data you want to receive.
personal computer, if necessary, so that you
4. Click Receive. MapSource begins receiving
can send information to MapSource.
data from your GPS unit or card reader. The
2. Click Receive From Device , or click data appears in the correct tab on the left side
Transfer > Receive From Device. The name of the window.
of your GPS unit or card reader should appear
automatically in the Device menu. If not, click
Find Device.
Creating and Editing Routes To create a route using the Route Properties
Routes tell you how to get from one place to another. dialog box:
Depending on your MapSource product, you can create 1. Press Ctrl + R or click Edit > New Route to
a direct route (a straight-line route), or an auto-route open the Route Properties dialog box.
(turn-by-turn over roads). 2. To add an existing waypoint to the route, click
Insert Waypoint. Select the waypoint from the
Creating Routes list that appears. To select multiple waypoints,
You can create and modify routes in MapSource by press the Ctrl or Shift key while you click
using the Route Properties dialog box, the Route tool several waypoints. Then click OK.
, or the Waypoints tab. A route can contain several 3. To add a city, point of interest, address, or
points; each point is called a via point. intersection, click the Find Places button
inside the dialog box.
NOTE: Not all MapSource products can create 4. Repeat steps 2–3 until you are finished adding
an auto-route. You must be using a routable points to your route. Each point you add is
MapSource product for MapSource to calculate listed in order from first to last under the Via
an auto-route. Points tab.
5. To rearrange the points in the list, highlight each
point and click the arrows to move the point up
or down in the list. To reorder the points from
last to first, click Invert.
Customizing MapSource
After you become comfortable using MapSource, you
may want to customize preferences to meet your needs.
You can change many settings by opening MapSource
Preferences. Click Edit > Preferences to open the
Preferences dialog box.
Filtering Tracks
Each track point contains time, position, and speed
information. From the Track Properties dialog box,
click Filter. When you filter a track you have loaded
from your GPS unit, you tell MapSource which track
points you want to keep and which to discard. You can
filter track points by time or distance, or you can let Preferences dialog box
MapSource filter the track points automatically.
WARNINGS AND CAUTIONS WARNING: This product has been produced, in part or whole,
from the United Kingdom Hydrographic Office products. No
CAUTION: GARMIN MAKES NO WARRANTY AS TO liability is accepted for the use of this product and it must not
THE ACCURACY OR COMPLETENESS OF THE MAP be used to assist in navigation. The digital chart(s) contained
DATA IN THIS PRODUCT AND DISCLAIMS ANY AND herein have not been verified or updated. For your safety,
ALL EXPRESS, IMPLIED, OR STATUTORY WARRANTIES, users are advised to consult official updated nautical charts for
INCLUDING ANY IMPLIED WARRANTY OF navigational purposes. The Hydrographic Office has not verified
MERCHANTABILITY OR FITNESS FOR A PARTICULAR the extracted data and the printed chart should be consulted for
PURPOSE. IT IS THE USER’S RESPONSIBILITY TO full navigational details.
USE THIS PRODUCT PRUDENTLY. THIS PRODUCT IS CAUTION: The Australian Hydrographic Office does not
INTENDED TO BE USED ONLY AS A TRAVEL AID AND check the information on this product and the Commonwealth
MUST NOT BE USED FOR ANY PURPOSE REQUIRING accepts no liability for the accuracy of copying or for any
PRECISE MEASUREMENT OF DIRECTION, DISTANCE, modifications that may have been made to the information
LOCATION, OR TOPOGRAPHY. which it has supplied. Furthermore, the Commonwealth does
The following Warnings and Cautions may apply to some or all not warrant that this product meets any regulations as an
of the content in the MapSource BlueChart® installation disk: appropriate product for navigation or that it contains the latest
WARNING: No National Hydrographic Office has verified hydrographic information available.
the information in this product and none accept liability for the
accuracy of reproduction or any modifications made thereafter.
No National Hydrographic Office warrants that this product
satisfies national or international regulations regarding the use
of the appropriate products for navigation.
W
Warnings and Cautions 24
Waypoints 17–20
adding to routes 20–24
creating 17
creating custom symbols
18
editing 18
selecting maps around
12–16
Waypoints Tab 17
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com