Professional Documents
Culture Documents
INSTRUCTION MANUAL
COMMUNICATIONS RECEIVER
iR10
This device complies with Part 15 of the FCC rules. Operation is sub-
ject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IC-R10.qxd 02.1.10 11:44 Page i (1,1)
IMPORTANT CAUTIONS
READ ALL INSTRUCTIONS CAREFULLY be- RWARNING! NEVER connect the receiver to an AC
fore attempting to operate the receiver. outlet. This may pose a fire hazard or result in an electric
shock.
SAVE THIS INSTRUCTION MANUAL — This
instruction manual contains important safety and operating in- RWARNING! NEVER operate the receiver with a
structions for the IC-R10. headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the
volume level or discontinue use.
EXPLICIT DEFINITIONS
NEVER connect the receiver to a power source of more
The following explicit definitions apply to this manual. than 16 V DC such as a 24 V battery. This connection will ruin
WORD DEFINITION the receiver.
Personal injury, fire hazard or electric shock
RWARNING may occur. NEVER cut the DC power cable between the DC plug and
fuse holder. If an incorrect connection is made after cutting,
CAUTION Equipment damage may occur.
the receiver might be damaged.
If disregarded, inconvenience only. No risk
NOTE of personal injury, fire or electric shock. NEVER expose the receiver to rain, snow or any liquids.
Versions of the IC-R10 which display the “CE” symbol on DO NOT connect the receiver to a power source using re-
the serial number seal, comply with the ETSI specifica- verse polarity. This connection will not only blow fuses but
tion prETS300 684 (EMC product standard for also may damage the receiver.
Commercially Available Amateur Radio Equipment).
i
IC-R10.qxd 02.1.10 11:44 Page ii (1,1)
UNPACKING
Accessories included with the receiver:
DO NOT use or place the receiver in areas with tempera- Qty.
tures below –10°C (+14°F) or above +50°C (+122°F) or, in
q Antenna............................................................................1
areas subject to direct sunlight, such as the dashboard.
w Handstrap.........................................................................1
AVOID placing the receiver in excessively dusty environ- e Belt clip (with 2 screws)....................................................1
ments. r Wall charger*....................................................................1
t Ni-Cd batteries .................................................................4
AVOID the use of chemical agents such as benzine or al- * Not supplied with some versions.
cohol when cleaning, as they damage the receiver surfaces.
ii
IC-R10.qxd 02.1.10 11:44 Page iii (1,1)
TABLE OF CONTENTS
IMPORTANT ..................................................................................... i 4 MEMORY MODE .............................................................. 23 – 34
EXPLICIT DEFINITIONS .................................................................. i ■ General ................................................................................................ 23
CAUTIONS ....................................................................................... i ■ Selecting memory mode ...................................................................... 23
UNPACKING .................................................................................... ii ■ Setting a bank and memory channel ................................................... 24
TABLE OF CONTENTS .................................................................. iii ■ Programming a memory channel—1 ................................................... 25
OPERATING THEORY ................................................................... iv ■ Programming a memory channel—2 ................................................... 26
OPERATING NOTES ...................................................................... iv ■ Programming a memory channel—3 ................................................... 27
■ Programming example 1 ..................................................................... 29
1 PANEL DESCRIPTION ......................................................... 1 – 6 ■ Programming example 2 ..................................................................... 30
■ Front and side panels ............................................................................ 1 ■ Programming example 3 ..................................................................... 31
■ Top panel ............................................................................................... 2 ■ Memory copy ....................................................................................... 33
■ Function display ..................................................................................... 3 ■ Copying example 1 .............................................................................. 34
■ Keypad .................................................................................................. 5 ■ Copying example 2 .............................................................................. 34
2 Ni-Cd BATTERIES AND ACCESSORIES ............................ 7 – 9 5 SCANNING OPERATION ................................................. 35– 46
■ Charging Ni-Cd batteries ....................................................................... 7 ■ General ............................................................................................... 35
■ Charging precautions ............................................................................ 7 ■ Before scanning ................................................................................... 37
■ About Ni-Cd batteries ............................................................................ 7 ■ Full scan .............................................................................................. 39
■ Battery installation ................................................................................. 8 ■ Memory scan ....................................................................................... 39
■ Charging connections ............................................................................ 8 ■ Program scan ...................................................................................... 40
■ Accessory attachment ........................................................................... 9 ■ Auto memory write scan ...................................................................... 41
3 BASIC OPERATION ......................................................... 10 – 22 ■ BANK scan .......................................................................................... 43
■ General ................................................................................................ 10 ■ Mode select scan ................................................................................. 44
■ Selecting VFO mode ........................................................................... 10 ■ Skip function ........................................................................................ 45
■ Selecting a receive mode .................................................................... 12 ■ SIGNAVI function ................................................................................. 46
■ Selecting a tuning step ........................................................................ 13 6 PRIORITY WATCH ........................................................... 47 – 49
■ Tuning a frequency (via the keypad) ................................................... 14 ■ General ............................................................................................... 47
■ Tuning a frequency (via the [DIAL]) ..................................................... 15
■ Dial select steps .................................................................................. 16 7 EASY MODE ............................................................................ 50
■ Band scope function ............................................................................ 17 ■ General ................................................................................................ 50
■ Listening example 1 ............................................................................. 19 ■ EASY mode operation ........................................................................ 50
■ Listening example 2 ............................................................................. 21
8 EDIT FUNCTION .............................................................. 51 – 58
iii
IC-R10.qxd 02.1.10 11:44 Page iv (1,1)
1 PANEL DESCRIPTION
SPEAKER
Emits the receive audio.
1
IC-R10.qxd 02.1.10 11:44 Page 2 (1,1)
PANEL DESCRIPTION 1
■ Top panel
2
IC-R10.qxd 02.1.10 11:44 Page 3 (1,1)
1 PANEL DESCRIPTION
■ Function display
q w e r t y u i !0 o
!1
3
IC-R10.qxd 02.1.10 11:44 Page 4 (1,1)
PANEL DESCRIPTION 1
u VSC INDICATOR
Appears while the VSC function is turned ON (p. 38).
i ATTENUATOR INDICATOR
Appears while the attenuator is turned ON (p. 65).
o AFC INDICATOR
Appears while the AFC function is turned ON (p. 63).
4
IC-R10.qxd 02.1.10 11:44 Page 5 (1,1)
1 PANEL DESCRIPTION
■ Keypad
KEY PRIMARY FUNCTION SECONDARY FUNCTION (while pushing [FUNC])
Push for 1 sec. to toggle power ON and OFF. Opening mes-
POWER Not available
sage appears for 1 sec. after power ON (p. 10).
MONI Push and hold this switch to force the squelch open (p. 64). Not available
TS
Selects a receive mode: FM, AM, USB, LSB, CW or WFM
MODE Selects tuning step set mode (p. 13).
(p. 12).
SET Clears numeric key input (p. 14).
CLR
Selects SET mode (p. 59).
Stops scanning (p. 39).
SCAN
Starts/stops scanning (p. 39). In VFO mode: selects a dial select step (p. 16).
SEARCH
EASY
Selects EASY mode (p. 50). Selects memory channel name search mode (p. 67).
LOCK
Selects memory edit mode. (except when in VFO mode; p. Locks all switches and controls electronically except [VOL],
EDIT 51). [SQL], [FUNC], [POWER] and [MONI] (p. 64).
NB/ANL In VFO mode: enters the selected receive frequency (p. 14).
Activates the noise blanker while in SSB and CW mode, or
ENT
In MEMORY mode: enters the selected memory channel by
the ANL function while in AM mode (p. 65).
the memory search function (p. 68).
5
IC-R10.qxd 02.1.10 11:44 Page 6 (1,1)
PANEL DESCRIPTION 1
1 When FM receive mode is selected in VFO mode: toggles the band scope function (p. 17).
VSC
SLEEP
3
Selects the sleep timer conditions (p. 66).
5 4 5 6 In VFO mode: sets program scan edge frequencies for auto memory write scan (p. 41).
BANK-S
8
In MEMORY mode: sets the BANK for bank scan (p. 43).
PRIO
9
Starts/stop priority watch (p. 49).
ATT
6
IC-R10.qxd 02.1.10 11:44 Page 7 (1,1)
RB
RC
hausted under normal conditions. We recommend battery rechargeable batteries. The batteries are recy-
C
RBR
charging just after receiving becomes impossible. clable. At the end of their useful life, under vari-
Ni-Cd ous state and local laws, it may be illegal to
dispose of these batteries into the municipal waste stream.
■ Charging precautions Call 1-800-8-BATTERY for battery recycling options in your
area or contact your dealer.
NEVER attempt to charge dry cell batteries. This will cause
internal liquid leakage and damage the receiver.
7
IC-R10.qxd 02.1.25 13:10 Page 8 (1,1)
BC-110A/E/D/V*
*Not supplied with
some versions.
Install 4 AA (R6) size dry cell, alkaline or the supplied Ni-Cd to [DC] CP-12L (optional)
batteries into the receiver. To cigarette lighter
socket
Black
CHARGE
CAUTION: Make sure the polarity of the batteries is cor- OFF ON
CAUTION: Make sure the
rect before installing. Reverse polarity may damage the re- [CHARGE] switch is in the OFF po-
ceiver. sition when operating the receiver
NOTE: DO NOT use different types of batteries at the with one of the above power sup-
same time otherwise the receiver may not work properly. plies.
8
IC-R10.qxd 02.1.10 11:44 Page 9 (1,1)
■ Accessory attachment
Antenna Belt clip Handstrap
Insert the supplied antenna into the Attach the belt clip using the supplied Attach the handstrap as shown in the
antenna connector and rotate the an- screws. diagram below. Facilities carrying.
tenna as shown in the diagram Conveniently attaches to your belt.
below. Keep the jack cover attached
when jacks are not in use to avoid
bad contacts.
9
IC-R10.qxd 02.1.10 11:44 Page 10 (1,1)
BASIC OPERATION 3
■ General ■ Selecting VFO mode
Operating the IC-R10 is easy. However,
in order to get the most out of its oper- 1. Turn power ON 2. Adjust the volume
ating potential, please go through the Push [POWER] for 1 sec. to turn Adjust the audio to a suitable level
following procedures, step-by-step. power ON. using [VOL].
Then, try the examples contained at the • Opening message is displayed for 1
end of this chapter. sec.
What is VFO?
The IC-R10 has several operating
modes, each of which has its own dis-
tinct functions. VFO (Variable
Frequency Operation) is one of these
modes.
10
IC-R10.qxd 02.1.10 11:44 Page 11 (1,1)
3 BASIC OPERATION
3. Adjust the squelch 3-1. Adjust the RF gain 4. Select VFO mode
Rotate [SQL] maximum counter- Rotate [SQL] maximum counter- When MEMORY mode is selected,
clockwise, then rotate it clockwise clockwise, to adjust RF gain to opti- push [V/M] to select VFO mode.
until audio is just muted when receiv- mum level. When SET or TS set mode is se-
ing no signal for FM, WFM or AM lected, push [CLR] to select VFO
mode. (see right page) mode.
• The VFO indicator appears.
VFO indicator
VFO
FM
11
IC-R10.qxd 02.1.10 11:44 Page 12 (1,1)
BASIC OPERATION 3
144.0000
WFM TV broadcasting, FM broadcasting
USB, LSB commercial, amateur, short wave radio When programmed
(see p. 69)
CW commercial, amateur
VFO
FM
3 BASIC OPERATION
BASIC OPERATION 3
VFO 4 5 6
FM
7 8 9
AFC ATT NB/ANL
14
IC-R10.qxd 02.1.10 11:44 Page 15 (1,1)
3 BASIC OPERATION
15
IC-R10.qxd 02.1.10 11:44 Page 16 (1,1)
BASIC OPERATION 3
■ Dial select steps Changing the frequency with the dial select step
VFO
+
DIAL SEL 144.0000
FM
SCAN
144.0000 DIAL SEL
FM
VFO
SCAN
VFO
100 kHz FM
144.0000
DIAL SEL
1 MHz SCAN
10 MHz
100 MHz VFO
FM
144.0000
DIAL SEL
SCAN
16
IC-R10.qxd 02.1.10 11:44 Page 17 (1,1)
3 BASIC OPERATION
When the tuning step is set above 20 kHz, the band scope
function automatically changes its sweep step to 20 kHz. r
However, when the sweep step is changed to 20 kHz, the
tuning step remains the same.
e
Also, when a user-programmable tuning step is selected, the
band scope function automatically selects the 20 kHz sweep
step.
we t
17
IC-R10.qxd 02.1.10 11:44 Page 18 (1,1)
BASIC OPERATION 3
VFO
FM
144.0000
signal
strength
lower freq. higher freq.
displayed freq.
Repeat the above step or push [CLR] to turn OFF the band
scope function.
18
IC-R10.qxd 02.1.10 11:44 Page 19 (1,1)
3 BASIC OPERATION
19
IC-R10.qxd 02.1.10 11:44 Page 20 (1,1)
BASIC OPERATION 3
Use the keypad to enter the fre- Enter the frequency from the 100 kHz Rotate [DIAL] to search for nearby
quency — (example 59.75 MHz). digit when you want to change below stations above and below the tuned
the 1 MHz digit only — (example frequency.
[Example] from 59.75 MHz to 59.25 MHz).
VFO
WFM
59.2000
5
WFM
VFO [Example]
. 59
9
. VFO
WFM
[DIAL]
59.
VFO
WFM
59.2500
. VFO
WFM
59.
2 VFO
WFM
59. 25 [DIAL]
5 VFO
WFM
59.3000
7 VFO
WFM
59. 75
5
ENT VFO
WFM
ENT VFO
59.2500 NOTE: WFM and regular FM share the
WFM
same circuit. Depending on the receive
59.7500 condition, this may result in distortion.
In such cases, try lowering the fre-
quency 30–50 kHz.
20
IC-R10.qxd 02.1.10 11:44 Page 21 (1,1)
3 BASIC OPERATION
21
IC-R10.qxd 02.1.10 11:44 Page 22 (1,1)
BASIC OPERATION 3
Enter a frequency of 118.0000 MHz* Enter the frequency from the 100 kHz Rotate [DIAL] to search for nearby
using the keypad (p. 14). digit when you want to change below stations above and below the tuned
the 1 MHz digit only — (example frequency.
from 118 MHz to 118.925 MHz).
1 . VFO VFO
VFO
AM AM AM
1
118 118. 118.9000
8
ENT VFO
9 VFO [DIAL] VFO
AM AM AM
118.9250 118.9500
22
IC-R10.qxd 02.1.10 11:44 Page 23 (1,1)
4 MEMORY MODE
23
IC-R10.qxd 02.1.10 11:44 Page 24 (1,1)
MEMORY MODE 4
4 MEMORY MODE
25
IC-R10.qxd 02.1.10 11:44 Page 26 (1,1)
MEMORY MODE 4
26
IC-R10.qxd 02.1.10 11:44 Page 27 (1,1)
4 MEMORY MODE
w
q
27
IC-R10.qxd 02.1.10 11:44 Page 28 (1,1)
MEMORY MODE 4
t Push [EDIT], then rotate [DIAL] to select the attenuator When you want to return to VFO mode immediately, push
condition. [EDIT] for 2 sec. at any time.
28
IC-R10.qxd 02.1.10 11:44 Page 29 (1,1)
4 MEMORY MODE
B07 .
7
.
BLANK 0 VFO
AM
29
IC-R10.qxd 02.1.10 11:44 Page 30 (1,1)
MEMORY MODE 4
5 VFO
e Rotate [DIAL] select channel “45”
WFM
or push [4] and [5] to enter the
59.7500
9
30
IC-R10.qxd 02.1.10 11:44 Page 31 (1,1)
4 MEMORY MODE
■ Programming example 3 — (121.5 MHz, EMER.,AM, SKIP: OFF, ATT: OFF, Aviation to channel F01)
1. Setting the frequency 2. BANK and memory 3. Programming details
channel setting
q Push [V/M] to select VFO mode. q While pushing [FUNC], push q Push [EDIT] to enter memory set-
w Rotate [DIAL] or push numeral [(V/M)MW]. ting mode.
keys to enter 121.5 MHz. w While pushing [FUNC], rotate EDIT VFO
FM
[DIAL] to select BANK “F”.
SET CH NAME
FUNC
FM
VFO
F01
+
SET BANK w Rotate [DIAL] until the character
F: “E” appears then push [ENT] or
1 VFO [DIAL] push [3] twice to enter the “E.”
FM
121.5000
2
VFO
FM
e Rotate [DIAL] or push [0] then [1]
SET CH NAME
1
SET CH NO.
3
[DIAL] 52
F01 BLANK
e Rotate the [DIAL] then push [ENT]
to enter the characters ”M”, “E”,
“R” and “.” for memory names or
push numeral keys (see page 72
for alphanumeric key assign-
ments).
31
IC-R10.qxd 02.1.10 11:44 Page 32 (1,1)
MEMORY MODE 4
ATT: OFF
VFO
FM EDIT VFO
32
IC-R10.qxd 02.1.10 11:44 Page 33 (1,1)
4 MEMORY MODE
■ Memory copy
What is the memory copy function?
The memory copy function copies the contents (minus BANK Copy to the other memory channel
names) of the selected memory channel to VFO or to another q Push [V/M] to select memory mode. (p. 23)
memory channel. This is quite useful when you want to w Select the BANK and memory channel you want to copy
search for signals around the displayed frequency or when (p. 24).
you want to edit memory channels. e While pushing [FUNC], push [(V/M)MW].
r Set the BANK and channel number you want to copy to
(p. 24).
Copy to VFO mode t While pushing [FUNC], push [(V/M)MW] for 2 sec.
q Push [V/M] to select memory mode.
w Select the BANK and memory channel you want to copy
(p. 24).
e While pushing [FUNC], push wr
[(V/M)MW] for 2sec.
w
e
r
t
qe t
wr
33
IC-R10.qxd 02.1.10 11:44 Page 34 (1,1)
MEMORY MODE 4
+
MW
MEMO
V/M AM
MEMORY COPY
FUNC MEMO
WFM
+
MW
A45 59.7500 r While pushing [FUNC], FUNC MEMO
AM
rotate [DIAL] to select
V/M
BANK “F”.
+ SET BANK
F:Aviation
[DIAL]
WFM
VFO
t Rotate [DIAL], or push MEMO
59.7500
AM
[0], [2] to select chan-
nel “02”.
[DIAL] SET CH NO.
F02 BLANK
y While pushing [FUNC], FUNC MEMO
AM
push [(V/M)MW] for 2
sec. to transfer the
+
MW F02 118.0250
V/M
contents of B07 to F02.
34
IC-R10.qxd 02.1.10 11:44 Page 35 (1,1)
5 SCANNING OPERATION
MEMORY SCAN
What is scanning?
Blank
Scanning is an automatic search function that detects signals A03
A02
as it checks through a range of frequencies or memory chan- A04
nels.
A01
A05
Scanning functions are useful for discovering new frequen-
cies to listen to or for searching through previously pro- B01–R99 A49
grammed frequencies for signals. B00
35
IC-R10.qxd 02.1.10 11:44 Page 36 (1,1)
SCANNING OPERATION 5
36
IC-R10.qxd 02.1.10 11:44 Page 37 (1,1)
5 SCANNING OPERATION
■ Before scanning
Set the following conditions before
scanning. 1. Set receive mode 2. Set the volume and
squelch levels
Set any receive mode EXCEPT USB, Set [VOL] to a suitable audio output
LSB and CW. level.
Set [SQL] so that the noise audio is
INFORMATION just muted.
What happens when you rotate the tun-
ing dial during scanning?
While scanning—
Scanning direction is changed.
Example:
If you rotate [DIAL] counterclockwise
while scanning up (frequency/memory
channel number increase), scan
changes to down scanning (fre-
quency/memory channel number de- The squelch control activates for RF
crease). gain control while USB, LSB, or CW
mode is selected. RF gain control
While pausing— does not activate for audio noise
muting, therefore, the receiver is in a
Scanning starts again (pause is can-
busy condition at all times. In such
celled).
case, searching speed is either very
slow or searching doesn’t even start.
37
IC-R10.qxd 02.1.10 11:44 Page 38 (1,1)
SCANNING OPERATION 5
38
IC-R10.qxd 02.1.10 11:44 Page 39 (1,1)
5 SCANNING OPERATION
SCANNING OPERATION 5
144.0000
1. Select program scan channel
Flashes while scanning
q Push [V/M] to select VFO mode (p. 11).
To change the direction of the scan, rotate [DIAL] during
w While pushing FUNC VFO scanning.
FM
[FUNC], push
[(4)PROG-S].
+
PROG-S
PROGRAM SCAN
When the program skip
4 00 function is ON (p. 61), fre- FM
VFO
40
IC-R10.qxd 02.1.10 11:44 Page 41 (1,1)
5 SCANNING OPERATION
channels. The same frequency ranges used for program scan 144.0000
are used for auto memory write scan.
Displays “PROGRAM
AMWS” with program FM
VFO
SCANNING OPERATION 5
42
IC-R10.qxd 02.1.10 11:44 Page 43 (1,1)
5 SCANNING OPERATION
F01 121.5000
1. Select BANK scan and BANK number
Flashes while scanning
q Push [V/M] to select MEMORY mode (p. 23).
To change the scan direction, rotate [DIAL] during scan-
w While pushing ning.
FUNC MEMO
FM
[FUNC], push
[(8)BANK-S].
+
BANK-S BANK SCAN
8 A: When the memory skip MEMO
AM
function is ON (p. 61),
F01 121.5000
specified memory chan-
Rotate [DIAL] to se- MEMO SKIP
lect the BANK num-
FM nels (p. 56) are skipped.
ber.
[DIAL] BANK SCAN Also, “SKIP” is dis-
F:Aviation played. Skip indicator
43
IC-R10.qxd 02.1.10 11:44 Page 44 (1,1)
SCANNING OPERATION 5
F01 121.5000
1. Select mode select scan and mode
Flashes while scanning
q Push [V/M] to select MEMORY mode (p. 23).
To change the scan direction, rotate [DIAL] during scan-
w While pushing MEMO
ning.
FUNC
FM
[FUNC], push
[(7)MODE-S].
+
MODE-S MODE SCAN
7
When the memory skip func- MEMO
AM
Displays “MODE SCAN”. tion is ON (p. 61), specified
memory channels (p. 56) are
F01 121.5000
skipped. Also, “SKIP” is
SKIP
e Push [MODE] once MODE MEMO
mode.
Push [CLR] or [SCAN] to stop scanning.
44
IC-R10.qxd 02.1.10 11:44 Page 45 (1,1)
5 SCANNING OPERATION
45
IC-R10.qxd 02.1.10 11:44 Page 46 (1,1)
SCANNING OPERATION 5
144.0000
FUNC VFO
FM e Push [SCAN] or [CLR] to stop
+
SIGNAVI 144.0000 scanning.
6 SIGNAVI
46
IC-R10.qxd 02.1.10 11:44 Page 47 (1,1)
6 PRIORITY WATCH
47
IC-R10.qxd 02.1.10 11:44 Page 48 (1,1)
PRIORITY WATCH 6
A01 A32
48
IC-R10.qxd 02.1.10 11:44 Page 49 (1,1)
6 PRIORITY WATCH
59 7500
after beep 121.5000
MEMO
AM
Appears while watching
PRIO SET frequency or band
121.5000
While pushing [FUNC], push [(9)PRIO], or push [CLR] only
after 2 sec.
to stop priority watch.
Start priority watch MEMO
AM
automatically. F01 121.5000
121 5000
49
IC-R10.qxd 02.1.10 11:44 Page 50 (1,1)
EASY MODE 7
■ General ■ EASY mode operation
The IC-R10 has an EASY mode which
provides simple operation by only scan- 1. Select EASY mode 2. Select frequency range
ning programmed frequency ranges. and start scanning
When you select EASY mode, 1 of 10 Push [EASY] to select EASY mode. q Push a numeral key to select a
pre-programmed frequency ranges can frequency range to search.
be selected.
w Push [SCAN] to
10 different frequency ranges are pro- start scanning.
grammed for EASY mode operation in
some transceiver versions; however, e Push [SCAN] or
0.5–1300.0000 MHz with FM receive [CLR] to stop
mode is pre-programmed into all 10 scanning.
channels in other versions.
0: 0.5000 0: 0.5000
8 EDIT FUNCTION
51
IC-R10.qxd 02.1.10 11:44 Page 52 (1,1)
EDIT FUNCTION 8
EDIT EDIT
EDIT * 1 or CLR * 2
EDIT EDIT
MEMO MEMO
FM EDIT FM
52
IC-R10.qxd 02.1.10 11:44 Page 53 (1,1)
8 EDIT FUNCTION
53
IC-R10.qxd 02.1.10 11:44 Page 54 (1,1)
EDIT FUNCTION 8
54
IC-R10.qxd 02.1.10 11:44 Page 55 (1,1)
8 EDIT FUNCTION
55
IC-R10.qxd 02.1.10 11:44 Page 56 (1,1)
EDIT FUNCTION 8
Program/auto-memory write scan and EASY mode channel edit flow chart
0: 144.0000
VFO EASY VFO EASY
FM FM
56
IC-R10.qxd 02.1.10 11:44 Page 57 (1,1)
8 EDIT FUNCTION
q Push [V/M] or [EDIT] to select q Enter channel q Enter the start frequency via the
VFO or EASY mode (p. 11 or 50). q names from the keypad or [DIAL].
w While pushing [FUNC], push keypad or by ro- w Push [EDIT] to change the item.
[(4)PROG-S] or [(5)AMWS] to se- tating [DIAL].
lect program or auto-memory write • When you enter q
scan mode; then select the scan channel names
with [DIAL] or a
channel (pgs. 40, 41) when VFO character assigned
mode is selected in q, push digit to the same key,
key to select scan channel when push [ENT] before
EASY mode is you enter the next
selected in q. character to
q
change the digit
w
(see page 72 for
e Push [EDIT] alphanumeric key
to enter assignments). q
w w
memory edit w Push [EDIT] to change the item.
mode. either either
w
q
[DIAL] SET CH NAME [DIAL] START FRQ
w
e
or or 144.0000
digit digit
key key
57
IC-R10.qxd 02.1.10 11:44 Page 58 (1,1)
EDIT MODE 8
4. Set end frequency 5. Set receive mode and 6. Set scan delay time
tuning step
q Enter the start frequency via the q Rotate [DIAL] to select receive q Rotate [DIAL] to select scan delay
keypad or [DIAL]. mode. time.
w Push [EDIT] to change the item. either either
q FM
VFO EASY
FM
VFO EASY
58
IC-R10.qxd 02.1.10 11:44 Page 59 (1,1)
9 SET MODE
A00 144.0000
CLR
tions to suit your operating require-
ments. EASY
FM
SET MODE 9
CONTRAST
LOW HI
60
IC-R10.qxd 02.1.10 11:44 Page 61 (1,1)
9 SET MODE
61
IC-R10.qxd 02.1.10 11:44 Page 62 (1,1)
SET MODE 9
CI-V BAUD
SCAN DELAY CI-V ADDRESS 300 CI-V TRN
5SEC 01 OFF
1200
4800
62
IC-R10.qxd 02.1.10 11:44 Page 63 (1,1)
10 OTHER FUNCTIONS
Setting AFC
VFO
While pushing [FUNC], push [(.)AFC] to toggle the AFC
FM
function ON and OFF.
144.0000
LOW BATTERY
appears once every 5 sec.
Appears
FUNC VFO
FM AFC
+
AFC 144.0000
.
63
IC-R10.qxd 02.1.10 11:44 Page 64 (1,1)
OTHER FUNCTIONS 10
Appears
FUNC VFO
FM
+
LOCK 144.0000
EDIT
64
IC-R10.qxd 02.1.10 11:44 Page 65 (1,1)
10 OTHER FUNCTIONS
FUNC VFO
AM
+ 118.0000
NB/ANL
ANL
Appears ENT
Appears
FUNC VFO AT T
FM
+
ATT
144.0000
0 FUNC VFO
USB
+
NB/ANL
14.1950
ENT NB
Appears
65
IC-R10.qxd 02.1.10 11:44 Page 66 (1,1)
OTHER FUNCTIONS 10
q While pushing [FUNC], push [(3)SLEEP] one or more times to set the sleep timer Set tuning step
condition.
w Release [FUNC] to set the selected condition. q Enter tuning step set mode (p.
e When the specified time elapses, the receiver emits 5 beeps then powers OFF. 13), then rotate [DIAL] until
“USER TS” appears.
*When you want to VFO
w Enter the desired tuning step
FUNC
SLEEP TIMER
3
first, then enter EASY SLEEP
kHz step).
mode. 3
40min
FM
VFO
e Push [CLR] to set tuning step and
SLEEP SLEEP TIMER return to VFO.
3
60min
release [FUNC]
VFO VFO
FM FM
144.0000 USER TS
TS 5.00kHz
Appears User TS default setting
66
IC-R10.qxd 02.1.10 11:44 Page 67 (1,1)
10 OTHER FUNCTIONS
FUNC MEMO
(ex.) MEMO
FM FM
+
SEARCH
NAME SEARCH NAME SEARCH
EASY [DIAL] E
or
2
67
IC-R10.qxd 02.1.10 11:44 Page 68 (1,1)
OTHER FUNCTIONS 10
MEMO
FM
MEMO
NAME SEARCH FM
MEMO MEMO
FM AM
68
IC-R10.qxd 02.1.10 11:44 Page 69 (1,1)
10 OTHER FUNCTIONS
69
IC-R10.qxd 02.1.10 11:44 Page 70 (1,1)
OTHER FUNCTIONS 10
70
IC-R10.qxd 02.1.10 11:44 Page 71 (1,1)
10 OTHER FUNCTIONS
■ Data cloning
The IC-R10 has receiver-to-receiver
data cloning capability. This function is
Set cloning mode and start cloning
useful when you want to copy all of the q Turn power OFF. e Connect an optional OPC-474 be-
programmed contents from one w While pushing [V/M], push tween both [SP] jacks.
IC-R10 to another. [POWER] for 1 sec. to enter OPC-474
cloning mode.
An optional OPC-474 CLONING CABLE
is required.
CLONE OUT
V/M
+
CLONE MODE
CLONE END
POWER
71
IC-R10.qxd 02.1.10 11:44 Page 72 (1,1)
1 Q (Q), Z(Z), 1(1) q (q), z(z), 1(1) !(exclamation mark) "(double quotation mark)
#(number) $(dollar sign)
2 A (A), B(B), C(C), 2(2) a (a), b(b), c(c)2(2)
%(percent sign) &(ampersand)
3 D (D), E(E), F(F), 3(3) d (d), e(e), f(f), 3(3) '(single quotation mark) ((left parenthesis)
4 G (G), H(H), I(I), 4(4) g (g), h(h), i(i), 4(4) )(right parenthesis) *(asterisk)
+(plus sign) /(slash)
5 J (J), K(K), L(L), 5(5) j (j), k(k), l(l), 5(5) :(colon) ;(semi-colon)
6 M (M), N(N), O(O), 6(6) m (m), n(n), o(o), 6(6) <(left angle bracket) =(equals sign)
>(right angle bracket) ?(question mark)
7 P (P), R(R), S(S), 7(7) p (p), r(r), s(s), 7(7) @(at symbol) [(left bracket)
8 T (T), U(U), V(V), 8(8) t (t), u(u), v(v), 8(8) \(yen symbol) ](right bracket)
9 W (W), X(X), Y(Y), 9(9) w (w), x(x), y(y), 9(9) ^(caret) _(under score)
`(grave accent) {(left brace)
0 0 (0) 0(0) |(bar) }(right brace)
. (period),
(space), (space), . (period),
.
, (comma), - (hyphen) , (comma), - (hyphen)
72
IC-R10.qxd 02.1.10 11:44 Page 73 (1,1)
12 CONTROL COMMANDS
■ General q
w
Preamble code (fixed)
Receiver’s default address
The IC-R10 can be connected to a PC via the PC’s RS-232C e Controller’s default address
port using an optional CT-17 CI-V LEVEL CONVERTOR. This r Command number (see table below)
allows you to control the receiver from the PC and/or transfer t Sub command number (see table below)
data from the receiver to the PC. y BCD code data for frequency entry
u End of message code (fixed)
Control is provided via Icom’s CI-V Communication Interface.
■ Command table
■ Data format Description
Transfers frequency data (transceive)
Cn
00
Sc
—
The CI-V system can be operated using the following data Transfers mode data (transceive) 01 —
formats. Data formats differ according to command numbers.
Reads display frequency 03 —
A data area is added for some commands.
Reads display mode 04 —
Controller ➡ IC-R10 Sets frequency data 05 —
73
IC-R10.qxd 02.1.10 11:44 Page 74 (1,1)
CONTROL COMMANDS 12
Computer
Power supply Optional
9–15VDC BC-25
RS-232C
cable
CT-17
to [CI-V]
IC-R10
CI-V connection example
74
IC-R10.qxd 02.1.10 11:44 Page 75 (1,1)
13 TROUBLESHOOTING
If your receiver seems to be malfunctioning, please check the
following points before sending it to a service center.
PROBLEM POSSIBLE CAUSE SOLUTION REF.
No power comes on. • The installed batteries are exhausted. • Charge the batteries or place new dry cell batter- p. 8
(A slight current flows in the circuits even when ies in the battery case.
the power is OFF.) (Remove the batteries if you will not be using the
receiver for a long time.)
• The batteries have been installed in reverse po- • Re-install the batteries in the correct orientation. p. 8
larity.
No audio is output. • [VOL] is turned to the minimum position. • Turn [VOL] to a suitable level. p. 10
• Earphone or headphone is connected. • Disconnect the earphone or headphone.
• The [SQL] is turned too far clockwise. • Turn the [SQL] counterclockwise. p. 11
• VSC function is activated. • Release the VSC function. p. 38
Weak reception, excessive • Not centered on the frequency. • Set to the center frequency using a small tuning p. 13
distortion or too much step.
noise. • Wrong receive mode is selected. • Select the correct receive mode. p. 12
• ATT function is activated. • Release the ATT function. p. 65
• The [SQL] (RF gain) is set too far clockwise (when • Turn the [SQL] (RF gain) counterclockwise. p. 11
USB, LSB or CW is selected).
• Batteries are nearly exhausted. • Charge the batteries or place new dry cell batter- p. 8
ies in the battery case.
Cannot tune frequency via • Lock function is ON. • While pushing [FUNC], push [(EDIT)LOCK] to turn p. 64
the keypad or [DIAL] the lock function OFF.
Cannot charge the installed • [CHARGE] is set to the OFF position. • Set [CHARGE] to the ON position. p. 8
Ni-Cd batteries.
75
IC-R10.qxd 02.1.10 11:44 Page 76 (1,1)
TROUBLESHOOTING 13
76
IC-R10.qxd 02.1.10 11:44 Page 77 (1,1)
14 SPECIFICATIONS
GENERAL RECEIVER
Frequency coverage : (Unit: MHz) Receive system : Triple-conversion superheterodyne
Version Frequency Range Intermediate frequencies :
0.5000– 823.9999 1st 266.7 MHz (340.0000–999.9999MHz)
U.S.A. 849.0001– 868.9999 429.1 MHz (except above freq.)
894.0001–1300.0000 2nd 10.7 MHz
Europe 0.5000–1300.0000 3rd 455 kHz
0.5000– 87.5000 Sensitivity :
France 108.0000–1300.0000
Freq. (MHz) FM WFM AM SSB/CW
Tuning steps : 0.1, 0.5, 1, 5, 6.25, 8, 9, 10, 12.5, 15, 0.5– 4.9999 0.5 µV — 1.6 µV 0.4 µV
20, 25, 30, 50 and 100 kHz 5– 74.9999 —
0.32 µV 1.0 µV 0.25 µV
or user programmable (0.1–999.99 75– 199.9999 1.0 µV
kHz/0.1 kHz steps) 200– 339.9999 0.45 µV 2.2 µV 1.6 µV 0.4 µV
Number of mem. channels : 1000 340– 699.9999 0.35 µV 1.3 µV 1.4 µV 0.32 µV
Receive modes : FM, AM, WFM, USB, LSB, CW 700– 799.9999 0.79 µV 2.0 µV 2.0 µV 0.63 µV
Antenna connector : BNC (50 Ω) 800– 899.9999 1.6 µV
0.5 µV 1.6 µV 0.4 µV
Power supply requirement : 4.8 V DC [4 AA (R6) Ni-Cd cells]; 900–1300.0000 —
4.8–16 V DC acceptable
Squelch sensitivity :
(negative ground)
Current drain (at 13.5 V DC) : Freq. (MHz) FM WFM AM
Rated audio 180 mA typ. 0.5– 4.9999 0.5 µV — 1.6 µV
Stand-by 110 mA typ. 5– 74.9999 —
0.32 µV 1.0 µV
Power saved 38 mA typ. 75– 199.9999 1.0 µV
Usable temperature range : –10˚C to +50˚C (+14˚F to +122˚F) 200– 339.9999 0.45 µV 2.2 µV 1.6 µV
Scan speed : 16.7 ch/sec. (programmed) 340– 699.9999 0.35 µV 1.3 µV 1.4 µV
6.25 ch/sec. (memory) 700– 799.9999 0.79 µV 2.0 µV 2.0 µV
Dimensions : 58.5(W) × 130(H) × 31.3(D) mm 800– 899.9999 1.6 µV
0.5 µV 1.6 µV
2.3(W) × 5.1(H) × 1.2(D) in 900–1300.0000 —
Weight : 310 g; 10.9 oz. Selectivity : AM, FM More than 15 kHz/6 dB
CI-V connector : 3-conductor 3.5 (d) mm (1/8 in) SSB More than 4 kHz/6 dB
WFM More than 150 kHz/6 dB
All stated specifications are subject to change without notice Audio output power : More than 120 mV at 10 % distortion
or obligation. with an 8 Ω load
77 External speaker connector : 3-conductor 3.5 (d) mm (1/8 in)
IC-R10.qxd 02.1.10 11:44 Page 78 (1,1)
OPTIONS 15
• CS-R10 CLONING SOFTWARE + OPC-478 CLONING CABLE
Allows you to transfer data from memories, etc., quickly and
easily edit and store data via an IBM compatible PC.
• LC-140 CARRYING CASE
Protects the receiver from everyday wear and tear.
• CT-17 CI-V LEVEL CONVERTOR
For receiver remote control using an IBM compatible per-
sonal computer.
• HP-4 HEADPHONE /SP-13 EARPHONE
Provides increased readability of signals in noisy environ-
ments and listening privacy.
• CP-12L CIGARETTE LIGHTER CABLE WITH NOISE FILTER
Allows you to operate the receiver through a 12 V cigarette
lighter socket.
• OPC-254L POWER CABLE
Allows you to operate the receiver with 4.5 to 16 V external
DC power.
• OPC-474 CLONING CABLE
Allows you to transfer data between receivers.
78
IC-R10.qxd 02.1.10 11:44 Page 79 (1,1)
A-5410H-1EX-t
Printed in Japan
Copyright 1996 by Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan