Professional Documents
Culture Documents
Exhibit:
A. Serial0/1.103
B. FastEthernet 0/1
C. Serail0/1.102
D. Serial0/0
E. FastEthernet 0/0
QUESTION NO: 2
Configuration exhibit:
You work as a network technician at TestKing.com. Study the exhibits carefully.
Assume that all router interfaces are operational and correctly configured. In
addition, assume that OSPF has been correctly configured on Router TestKing2.
How will the default route configured on TestKing1 affect the operation of
TestKing2?
A. Any Packet destined for a network that is not referenced in the routing table of Router
TestKing2 will be directed to TestKing1. TestKing1 will then send that packet back to
TestKing2 and a routing loop will occur
B. Any packet destined for a network that is not directly connected to router TestKing1
will be dropped
C. The networks directly connected to router TestKing2 will not be able to communicate
with the 172.16.100.0, 172.16.100.128 and 172.16.100.64 subnetworks
D. Any packet destined for a network that is not directly connected to Router TestKing2
will be dropped immediately because of the lack of a gateway on TestKing1
E. Any packet destined for a network that is not directly connected to router TestKing2
will be dropped immediately
F. None of the above
QUESTION NO: 3
QUESTION NO: 4
QUESTION NO: 5
Which of the following OSPF commands, when used together, will put the network
192.168.10.0/24 into OSPF area 0? (Select all valid responses)
QUESTION NO: 6
Under which circumstance, i.e. network type, would an OSPF router establish a
neighbor adjacency, even though the DR/BDR election process was not performed?
A. Point-to-point
B. Broadcast multicast
C. Nonbroadcast multicast
D. Backbone area 0
E. Virtual Link
QUESTION NO: 7
On the assumption that every OSPF router in a particular area is configured with
the same priority value; which secondary value would be used as a router ID when
there is no loopback interface set?
QUESTION NO: 8
On the topic of OSPF routing; which of the following are the traits of an OSPF
area? (Select all that apply)
QUESTION NO: 9
A. 1
B. 64
C. 1562
D. 64000
E. 1500
F. None of the above
QUESTION NO: 10
TestKing is using OSPF as the routing protocol in their network. What are some of
the characteristics of this routing protocol? (Select all valid answer choices)
QUESTION NO: 11
Which of the following are true statements regarding the characteristics of OSPF
areas? (Select all that apply)
QUESTION NO: 12
On what kinds of networks does the OSPF protocol elect a backup designated
router? (Select all that apply)
A. Point-to-point
B. Point to multipoint
C. Broadcast
D. Non-broadcast multi-access
E. None of the above
QUESTION NO: 13
Three TestKing routers are configured for OSPF area 0 as shown in the diagram
below:
You wish to ensure that router TK2 will be preferred as the designated router (DR)
for the 172.16.1.0 /24 LAN segment.
What configuration tasks could be used to establish this preference? (Choose all
that apply)
A. Configure the priority value of the Fa0/0 interface of RouterTK2 to a higher value than
any other interface on the Ethernet network.
B. Change the router id for Router TK2 by assigning the IP address 172.16.1.130/24 to
the Fa0/0 interface of RouterTK2.
C. Configure a loopback interface on RouterTK2 with an IP address higher than any IP
address on the other routers.
D. Change the priority value of the Fa0/0 interface of RouterTK2 to zero.
E.Change the priority values of the Fa0/0 interfaces of RouterTK1 and RouterTK3 to zero.
F. No further configuration is necessary.
G. All of the above will make TK2 the DR
QUESTION NO: 14
TestKing uses OSPF in their WAN. The OSPF Hello protocol performs which of the
following tasks in this network? (Choose two)
QUESTION NO: 15
TK1 and TK2 are OSPF routers on a point-point link. On this point-to-point
network, OSPF hello packets are addressed to which address?
A. 192.168.0.5
B. 254.255.255.255
C. 223.0.0.1
D. 172.16.0.1
E. 224.0.0.5
F. 127.0.0.1
G. None of the above
QUESTION NO: 16
Which of the following statements below best describe the process identifier that is
used to run OSPF on a TestKing router? (Choose two)
A. It is an optional parameter required only if multiple OSPF processes are running on the
router.
B. It is locally significant.
C. It is needed to identify a unique instance of an OSPF database.
D. All routers in the same OSPF area must have the same process ID if they are to
exchange routing information.
E. It is globally significant.
F. It is shared among all OSPF routers
QUESTION NO: 17
.
Router TestKing3 was just successfully rebooted. Based on the information shown
above, correctly identify the current OSPF router ID for Router TestKing3.
A. 220.173.149.10
B. 208.149.23.194
C. 208.149.23.162
D. 190.172.32.10
E. None of the above
QUESTION NO: 18
Prior to the command shown above, you had configured OSPF with the command:
TestKing3(config-router)# network 192.168.12.64 0.0.0.63 area 0
After completing the configuration, you now discover that not all the interfaces are
participating in OSPF. Based on the information shown above, which three of the
interfaces will participate in OSPF according to this configuration statement?
(Choose three)
A. Serial0/1.104
B. Serial0/1.102
C. Serial0/0
D. Serial0/1.103
E. FastEthernet0 /1
F. FastEthernet0 /0
QUESTION NO: 19
Which one of the following privileged EXEC mode IOS show commands will display
the state of the OSPF DR/BDR (designated router / backup designated router)
election process?
QUESTION NO: 20
On your OSPF network, routers TK1 and TK2 belong to the same Ethernet
network. However, they are unable to establish an adjacency over this link. While
troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"
command on each router. The output from these commands is displayed below:
QUESTION NO: 21
Router TK1 is being installed. You wish to add this router to your existing OSPF
network. In doing so, you configure the following:
QUESTION NO: 22
QUESTION NO: 23
Based on the output from the show ip ospf neighbor command on TK-2, what must
a network administrator do to ensure that TK-2 will always be the DR and TK-3
will never be the DR or BDR for OSPF area 0? (Choose three.)
QUESTION NO: 24
Referring to the Testking Border router shown below, what can be concluded from
the output of this debug command?
Exhibit:
A. The output represents normal OSPF operation.
B. The OSPF router connected to interface Serial0/1 has NOT formed a neighbor
relationship with the Border router.
C. The interfaces of two OSPF routers connected to the Border router are in the same
subnet.
D. A router is connected to interface Serial0/3 of the Border router. The OSPF router ID
of the connected router is the IP address of the connected interface.
E. None of the above
QUESTION NO: 25
A. Testking-1
B. Testking-2
C. Testking-3
D. Testking-4
E. Branch-1
F. Branch-2
QUESTION NO: 26
TestKing is using OSPF in their WAN. What is the maximum number of hops OSPF
allows before it deems a network unreachable?
A. 15
B. 16
C. 99
D. 255
E. Unlimited
F. None of the above
QUESTION NO: 27
On the topic of the OSPF hello protocol; which of the statements below are true?
(Select two answer choices)
QUESTION NO: 28
You are an administrator and you've just configured OSPF on a router with both
physical and logical interfaces. Which of the following factors determine the router
ID?
QUESTION NO: 29
Under which network type circumstance would an OSPF router establish router
adjacencies while not performing the DR/BDR election process?
A. Point-to-point
B. Broadcast
C. Non-broadcast multi-access
D. Backbone area 0
E. None of the above
QUESTION NO: 30
On the topic of OSPF routing; which of the following are the traits of an OSPF
area? (Select three)
QUESTION NO: 31
Router TK1 is running OSPF. What is the default administrative distance (AD) of
this protocol?
A. 90
B. 100
C. 110
D. 120
E. 170
F. None of the above
QUESTION NO: 32
Router TK1 is running OSPF. On this router, what kind of packets does OSPF send
to keep up connectivity with its neighboring routers?
A. SPF packets
B. hello packets
C. keepalive packets
D. dead interval packets
E. LSU packets
QUESTION NO: 33
QUESTION NO: 34
Based on the information shown above, which two statements are true about the
loopback address that is configured on TK-B? (Choose two)