Professional Documents
Culture Documents
Way Radios
Radios bidirectionnelles
User Guide
Guide de l’utilisateur
CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Battery Features. . . . . . . . . . . . . . . . . . . . . . 13
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .5 About the Li-Ion Battery . . . . . . . . . . . . . 13
Package Contents . . . . . . . . . . . . . . . . . . . . . .5 Battery Recycling and Disposal . . . . . . . 14
FCC Licensing Information . . . . . . . . . . . . .7 Installing the Lithium-Ion
Canada Licensing Information . . . . . . . . . .7 (Li-Ion) Battery . . . . . . . . . . . . . . . . . . . . 15
General Information. . . . . . . . . . . . . . . . . . . . .7 Removing the Lithium-Ion
(Li-Ion) Battery . . . . . . . . . . . . . . . . . . . . 15
The License Application . . . . . . . . . . . . . . . . .7
Power Supply, Adaptor and
Batteries and Chargers
Safety Information . . . . . . . . . . . . . . . . . . . .8 Drop-in Tray Charger . . . . . . . . . . . . . . . 17
1
English
Getting Started . . . . . . . . . . . . . . . . . . . . . .27 Reading CTCSS/DPL Values . . . . . . . . 38
Turning radio ON/OFF. . . . . . . . . . . . . . . . . .27 Reading Auto-Scan Values . . . . . . . . . . 39
Adjusting Volume . . . . . . . . . . . . . . . . . . . . .27 Programming Frequencies, Codes
CONTENTS
2
English
Cloning with a Multi Unit Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Charger (MUC) . . . . . . . . . . . . . . . . . . . .49 Audio Accessories . . . . . . . . . . . . . . . . . . . . 71
Cloning Radio using the Radio Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
to Radio (R2R) Cloning Cable Carry Accessories . . . . . . . . . . . . . . . . . . . . 72
CONTENTS
(Optional Accessory). . . . . . . . . . . . . . . .51 Power Supplies AC Pin Adaptors. . . . . . . . . 72
Cloning using the CPS (Computer Software Applications. . . . . . . . . . . . . . . . . . 72
Programming Software) . . . . . . . . . . . . .53 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Troubleshooting . . . . . . . . . . . . . . . . . . . . .54
Power Supplies . . . . . . . . . . . . . . . . . . . . . . 73
Use and Care . . . . . . . . . . . . . . . . . . . . . . .58
Accessories . . . . . . . . . . . . . . . . . . . . . . . .71
3
English
This device complies with Part 15 of the FCC
SAFETY Rules. Operation is subject to the condition that
this device does not cause harmful
PRODUCT SAFETY AND RF
interference.
EXPOSURE COMPLIANCE
Before using this product,
read the operating
instructions and RF energy
! awareness information
Caution contained in the Product
SAFETY
ATTENTION!
This radio is restricted to occupational use only
to satisfy FCC RF energy exposure
requirements.
4
English
Business Radios,
INTRODUCTION
Mailstop 1C15, Motorola
Thank you for purchasing the Motorola® RM 8000 West Sunrise Boulevard
Series Radio. This radio is a product of Plantation, Florida 33322
Motorola's 80 plus years of experience as a
world leader in the designing and
manufacturing of communications equipment. PACKAGE CONTENTS
The RM Series radios provide cost-effective • Radio
communications for businesses such as retail
• Holster
stores, restaurants, schools, construction sites,
• Lithium-Ion Battery
manufacturing, property and hotel
• Power Supply
management and more. Motorola professional
two-way radios are the perfect communications • Quick Reference Guide
solution for all of today's fast-paced industries. • Warranty Card
Note: Read this user guide carefully to ensure you • Drop-in Tray Charger
know how to properly operate the radio
INTRODUCTION
• Product Safety & RF Exposure Booklet
before use
5
English
This User Guide can be downloaded from
www.motorolasolutions.com/RMSeries.
Product-related questions, contact:
6
English
(FCC). To transmit on these frequencies, you
FCC LICENSING are required to have a license issued by the
INFORMATION FCC. Application is made available on FCC
INTERFERENCE INFORMATION Form 601 and Schedules D, H, and Remittance
Form 159.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition that To obtain these FCC forms, request document
this device does not cause harmful 000601 which includes all forms and
interference. instructions. If you wish to have the document
FCC LICENSING
faxed, mailed or have questions, use the
INFORMATION
RM Series Business two-way radios operate
following contact information.
on radio frequencies that are regulated by the
Federal Communications Commission
9
English
Before filling out your application, you must Replacement of any transmitter component
decide which frequency(ies) you can operate (crystal, semiconductor, etc.) not authorized by
on. See “Frequencies and Code Charts”. For the FCC equipment authorization for this radio
questions on determining the radio frequency, could violate FCC rules.
call Motorola Product Services at:
Use of this radio outside the country where it
1-800-448-6686 was intended to be distributed is subject to
Changes or modifications not expressly government regulations and may be prohibited
FCC LICENSING
10
English
THE LICENSE APPLICATION
CANADA LICENSING
CANADA LICENSING
INFORMATION General Instructions
1. Fill in the items as per the instructions. If you
GENERAL INFORMATION
need additional space for any item use the
The operation of your Motorola radio is subject reverse side of the application.
to the Radiocommunications Act and must
2. Be sure to use a typewriter or print legibly.
comply with rules and regulations of the
3. Make a copy for your files.
Federal Government’s department of Industry
Canada. Industry Canada requires that all 4. Prepare a cheque or money order made out to
operators using Private Land Mobile the “Receiver General for Canada”, for an
frequencies obtain a radio license before amount, which is on the following schedule, for
operating their equipment. each radio purchased. (License is valid until
April 1st of each year, and the renewed.
An application for your Industry Canada license
is made on the form included with your radio. 5. Mail your completed application, along with your
Additional forms and latest license application cheque or money order to the closest Industry
versions can be obtained from the nearest Canada District office, according to the list on
Industry Canada District office. A list of these pages
offices is included for your information. To obtain the latest Canadian License
Application form, please go to:
www.ic.gc.ca
7
English
3. To reduce risk of damage to the electric plug
BATTERIES AND and cord, pull by the plug rather than the cord
CHARGERS SAFETY when disconnecting the charger.
INFORMATION 4. An extension cord should not be used unless
absolutely necessary. Use of an improper
This document contains important safety and
extension cord could result in risk of fire and
operating instructions. Read these instructions
BATTERIES AND CHARGERS
8
English
OPERATIONAL SAFETY • In equipment using fuses, replacements must
comply with the type and rating specified in the
GUIDELINES
equipment instructions.
• Turn the radio OFF when charging battery.
• Maximum ambient temperature around the power
• The charger is not suitable for outdoor use. Use supply equipment must not exceed 40°C (104°F).
only in dry locations/conditions.
• Power output from the power supply unit must not
SAFETY INFORMATION
and wired supply of the correct voltage (as located at the bottom of the charger.
specified on the product).
• Make sure that the cord is located where it will
• Disconnect charger from line voltage by removing not be stepped on, tripped over, or subjected to
main plug. water, damage, or stress.
9
English
RADIO OVERVIEW
PARTS OF THE RADIO
Antenna
On/Off/Volume
knob
Button
SB2- Scan/Nuisance
Lithium-Ion Channel delete
Model Label
battery
10
English
On/Off/Volume Knob Side Buttons
Used to turn the radio ON or OFF and to adjust Push-to-Talk (PTT) Button
the radio’s volume. • Press and hold down this button to talk,
Accessory Connector release to leasten it
Used to connect compatible audio accessories. Side Button 1 (SB1)
Model Label • The Side Button 1 is a general button
Indicates the model of the radio. that can be configured by the Computer
Microphone Programming Software - CPS. The
Speak clearly into the microphone when sending default setting of SB1 is ‘Monitor’.
a message. Side Button 2 (SB2)
Antenna On all RM Series radios, the antenna is • The Side Button 2 is a general button
non-removable that can be configured by the CPS. The
SB2 default setting is set to scroll until
LED Indicator
the desired channel is selected.
Used to give battery status, power-up status,
radio call information and scan status. RM Series provides a Li-Ion battery. For more
RADIO OVERVIEW
information, see “Battery Feature on Pg.13.
11
English
This User Guide covers multiple RM Series
models, and may detail some features your
radio does not have. The radio’s model is
shown on the bottom of the radio and provides
you the following information:
Transmit Number of
Model Frequency Power Antenna
Band Channels
(Watts)
12
English
BATTERY FEATURES which receives minimal overcharging and
averages only 25% discharge, lasts even
longer.
RADIO OVERVIEW
greater the overcharge and the deeper the Motorola rapid-rate battery chargers contain a
average discharge, the fewer cycles a battery temperature-sensing circuit to ensure that
will last. For example, a battery which is batteries are charged within the temperature
overcharged and discharged 100% several limits stated above.
times a day, lasts fewer cycles than a battery
that receives less of an overcharge and is
discharged to 50% per day. Further, a battery
13
English
Battery Recycling and Disposal Many retailers and dealers participate in this
Li-Ion rechargeable batteries can be recycled. program. For the location of the drop-off facility
However, recycling facilities may not be closest to you, access RBRC's Internet web
available in all areas. Under various U.S. state site at:
laws and the laws of several other countries, www.rbrc.com
batteries must be recycled and cannot be
or call:
disposed of in landfills or incinerators. Contact
your local waste management agency for 1-800-8-BATTERY
specific requirements and information in your
This internet site and telephone number also
area. Motorola fully endorses and encourages
provides other useful information concerning
the recycling of Li-Ion batteries. In the U.S. and recycling options for consumers, businesses
Canada, Motorola participates in the
and governmental agencies.
nationwide Rechargeable Battery Recycling
Corporation (RBRC) program for Li-Ion battery
collection and recycling.
RADIO OVERVIEW
14
English
Installing the Lithium-Ion (Li-Ion) Battery Removing the Lithium-Ion (Li-Ion) Battery
RADIO OVERVIEW
pack, fit the tabs at the bottom of the battery
into the slots at the bottom of the radio’s body.
3. Press the top part of the battery towards the
radio until a click is heard.
Note: To learn about the Li-Ion Battery Life
features, refer to “About the Li-Ion Battery”
on page 13
15
English
Holster Power Supply and Drop-in Tray Charger
RADIO OVERVIEW
then press the radio against the back of the
holster until the top clips are inserted in the
top latches of the battery.
17
English
Battery Life Information
When the Battery Save feature is ON (enabled by default) the battery life will be longer. The
following chart summarizes battery life estimations:
RADIO OVERVIEW
18
English
Charging the Battery Charging with the Drop-in Tray
The RM series radios offers two types Single Unit Charger (SUC)
of power supplies:
20
English
To charge only the battery - at step 4, insert the
RADIO OVERVIEW
battery into the tray, with the inside surface of
the battery facing the front of the charger, as
shown. Ensure the slots in the battery correctly
engage in the charger
21
English
Drop-in Tray Charger LED Indicators
RADIO OVERVIEW
23
English
Estimated Charging Time
The following table provides the estimated charging time of the battery. For further details, see
“Battery” on page 71.
RADIO OVERVIEW
25
English
Charging a Radio and Battery using Notes:
a Multi Unit Charger- MUC (Optional • This Multi Unit Charger also allows you to
Accessory) clone up to 2 radios (2 Source radios and 2
Target radios). Refer to page 51 for details.
26
English
GETTING STARTED SELECTING A CHANNEL
To select a channel, press SB2 side button until
GETTING STARTED
For the following explanations, refer to “Parts of you reach the desired channel.Voice
the Radio” on page 10. announcement will indicate the channel selected.
TURNING RADIO ON/OFF 2 channels are active with factory default setting.
To turn ON the radio, rotate the On/Off/Volume Refer to "Advanced Radio Configuration" on
Knob clockwise. The radio will chirp and the Page 34 to active more channels. The radio can
LED Indicator will briefly blink red. operate up to 4 channels.
To turn the radio OFF, rotate the On/Off/Volume Each channel has its own Frequency,
Knob counterclockwise until you hear a ‘click’ Interference Eliminator Code and Scan Settings.
and the radio LED Indicator turns OFF. TALKING AND MONITORING
ADJUSTING VOLUME It is important to monitor for traffic before
Turn the On/Off/Volume Knob clockwise to transmitting to avoid ‘talking over’ someone
increase the volume, or counterclockwise to who is already transmitting.
decrease the volume. To monitor, long press and hold the SB1(*)
Note: Do not hold the radio too close to the ear button to access channel traffic. If no activity is
when the volume is high or when present, you will hear ‘static’. To release, press
adjusting the volume. SB1 again. Once channel traffic has cleared,
proceed with your call by pressing the PTT
button. When transmitting, the LED Indicator will
be On solid red during transmission.
27
English
Notes: TALK RANGE
GETTING STARTED • To listen to all activity on a current channel, short
press the SB1 to set the CTCSS/DPL code to 0.
This feature is called ‘CTCSS/DPL Defeat
(Squelch set to SILENT)’.
• (*) This assumes SB1 is not being programmed
for a different mode.
RECEIVING A CALL
1. To select a channel, press SB2 side button
until you reach the desired channel, Voice
announcement will indicate the channel
selected
28
English
To establish a proper two-way communication, 4. Scramble Code: Codes that make the
the channel, frequency, and interference transmissions sound garbled to anyone
GETTING STARTED
eliminator codes must be the same on both listening who is not set to that specific code.
radios. This depends on the stored profile that 5. Bandwidth: Some frequencies have selectable
has been preprogrammed on the radio: channel spacing, which must match other
1. Channel: Current channel that the radio is radios for optimum audio quality (only
using, depending on radio model. available for RMU2043).
2. Frequency: The frequency the radio uses to For details on how to set up frequencies and
transmit/receive. CTCSS/DPL codes in the channels, refer to
3. Interference Eliminator Code: These codes “Programming Selection Mode” in page 36.
help minimize interference by providing a
choice of code combinations.
29
English
RADIO LED INDICATORS
GETTING STARTED
RADIO STATUS LED INDICATION
Channel Alias Edit Red heartbeat
Channel Busy Solid orange
Cloning Mode Two orange heartbeats
Cloning In Progress Solid orange
One green blink, one orange blink, one green blink, then repeat for 4
Fatal Error at Power up
seconds
Low Battery Orange blink
Low Battery Shutdown Orange heartbeat
Monitor LED is OFF
Power-Up Solid red for 2 seconds
‘Idle’ Programming Mode /
Green heartbeat
Channel Mode
Scan Mode Red Blink
Transmit (Tx)/Receive (RX) Solid red
30
English
HANDS-FREE USE/VOX 1. Turn the radio OFF.
GETTING STARTED
3. Insert the audio accessory’s plug firmly into
accessory port.
4. Turn radio ON. The LED Indicator will
blink double red.
5. Lower radio volume BEFORE placing
accessory near ear.
VOX
6. To transmit, speak into accessory microphone
Accessory
and to receive, stop talking.
Accessory
Port/ 7. VOX can be temporarily disabled by pressing
Connector the PTT button or by removing the audio
hands-free (VOX) when used with compatible Note: To order accessories, refer to:
VOX accessories. www.motorolasolutions.com/RMseries or
call 1 (800) 448-6686, or contact your
With Compatible VOX Accessories Motorola point of purchase
The default factory setting for VOX sensitivity
level is OFF. Before using VOX, set VOX
level to a setting different from ‘OFF’ via the
CPS (Customer Programming Software).
Then, perform the following steps:
31
English
Setting VOX Sensitivity Battery Save
GETTING STARTED The sensitivity of the radio's accessory or Battery Save feature extends battery life as
microphone can be adjusted to suit different your radio goes into ‘Idle’ state. To enable/
operating environments. VOX sensitivity can disable press SB1 and SB2 buttons
be programmed via the CPS. simultaneously for 2 or 3 seconds while
Default value is OFF. If you want to use the powering up the radio until you hear a quick
series of beeps. To have a slightly better attack
VOX feature, VOX level should be set at a
time, set Battery Save feature to OFF so that
value different from OFF.
the radio is always ready to transmit or receive
• 1 = Low audio input levels will trigger the Tx
without any delays.
• 2 = Medium sensitivity
Note: Battery Save feature is set to ON by default
• 3 = High audio input levels will trigger the Tx
Reset to Factory Defaults
Microphone Gain
Reset to Factory Defaults will set back all radio
The sensitivity of the microphone can be features to the original factory default settings.
adjusted to fit different users or operating To do so, press PTT, SB2 and SB1
environments. simultaneously while turning ON the radio until
This feature can be adjusted only through the you hear a high tone chirp.
CPS. Microphone default setting is set to 2 =
Medium Gain.
32
English
End of Transmission Tone (Roger Beep
Tone)
GETTING STARTED
Short press the SB1 button while turning ON
the radio to enable/disable End of
Transmission Tone.
Note: This setting is set to OFF by default
33
English
PROGRAMMING When the radio is set to Advanced
Configuration, you are able to read and modify
FEATURES
four features:
To easily program all the features in your radio,
• Frequency Selection
it is recommended to use the Costumer
• CTCSS/DPL Codes
Programming Software (CPS) and
• Auto-Scan.
programming cable.
• Active Channels
CPS software download is available for free
The Frequency Select feature allows you to
at www.motorolasolutions.com/RMseries
PROGRAMMING
Advanced Configuration
The Interference Eliminator Code (CTCSS/
Advanced Configuration is a configuration DPL) helps minimize interference by providing
mode that allows the customization of you with a choice of code combinations that
additional features via the front panel. filter out static, noise, and unwanted
The non-display models don't have a display messages.
to show programmed values, then The Auto-Scan feature allows you to set a
navigation is guided via voice prompt. particular channel to automatically enable Scan
each time you switch to that channel.
The Active Channels feature allows you to
increase or decrease the amount of channels
active (In the range of maximum channels).
34
English
Entering Advanced Configuration Mode Once you are in the 'Idle' Programming Mode,
Note: Before programming the features, make you will be able to hear the Frequencies,
Codes, Auto-Scan and active channels
sure your radio is set to the channel you
wish to program. You can do so before settings by short pressing the PTT button to
entering Advanced Configuration Mode move along the different programmable
or at any time during the Advanced features.
Configuration Mode by pressing SB2
Entering Frequencies Values
until reaching the desired channel.
RM Series radios have 89 frequencies for UHF.
To read or modify Frequencies, Codes,
PROGRAMMING
Auto-Scan or Active Channels, set the radio Once in ‘Idle’ Programming Mode, the first
FEATURES
to 'Advanced Configuration Mode' by value available to change is Channel number,
pressing and holding the PTT and SB1 you can change the channel by pressing SB2
buttons simultaneously for 3 to 5 seconds button until you reach desired Channel, voice
while powering up the radio and until you
announcement will indicate channel selected.
hear a voice prompt saying "Programming
Mode" and "Channel #". Using SB1 and SB2 you can change values.
The value selected is announced by voice
Note: 'Idle' Programming Mode is the stage of
prompt.
the Programming Mode in which the
radio is waiting for the user to start the
radio programming cycle.
37
English
Reading CTCSS/DPL Values Saving Settings
If you are satisfied with the setting, you
If you continue short pressing the PTT button can either:
the radio will move forward to programming
CTCSS/PL Codes. short press PTT to continue
•
After hearing the current value for CTCSS/PL programming,
Code you can scroll to a new code value
• long press PTT to save and return to
using the SB1 or SB2 button.
'Idle' Programming Mode, or
RM Series have up to 122 codes available
PROGRAMMING
(refer to “Frequencies and Codes Charts” long press the PTT button twice to exit
FEATURES
•
Section). 'Idle' Programming Mode and return to
Reading Auto-Scan Values the normal radio operation.
After hearing the CTCSS/DPL codes, short
press the PTT button and the radio will move Note:
forward to programming Auto-Scan. • If you do not wish to save the value you just
Auto-Scan only has two values: programmed, turn the radio OFF.
- Enabled
- Disabled • If you ‘roll-over’ to the beginning of ‘Idle’
Programming Mode you will hear "Channel #"
Note: While in Auto-Scan Mode, if you short press
and the LED Indicator will start blinking green
PTT button, the radio will move forward to
again. All values that were changed will be
programming the "Active Channels" feature, so
automatically saved.
you can modify the amount of channels
available for your unit using the SB1 or SB2
button.
38
English
Programming Mode FAQ 2. I am trying to program a frequency (or
1. I got distracted while programming and code) value but the radio would not do it.
forgot which feature I was It rolled over and took me back to value
programming. What should I do? ‘0’.
Return to 'Idle' Programming Mode and start
The radio will not allow you to program any
over.
values that are not available in the frequencies
• Long press the PTT button. The radio will return and codes pool. For example, if you try to
to the 'Idle' Programming Mode or, program code 128, the radio would not accept
PROGRAMMING
• Turn OFF the radio and enter Programming it, as the maximum value allowed is 122. Same
FEATURES
Mode again (see instructions in the beginning of thing will happen with frequencies. Check the
this section) Frequencies and Codes Charts section to
make sure you are programming a valid
number.
3. I am trying to enter the Programming
Mode but the radio would not do it.
40
English
4. When I was programming I made a 6. I am done programming the features in
mistake and programmed the wrong this channel and want to program another
value. How can I erase it or re-program channel.
it?
Press short PTT several times until you hear
If you make a mistake while programming a "Channel #", then switch channel using
value you have two choices: Channel Selector Knob. If you wish to save
the changes, make sure you are in the ‘Idle’
• The radio settings will roll-over each time
Programming Mode before switching the
they reach a maximum or minimum value.
channel as otherwise you will lose the changes
PROGRAMMING
Keep increasing (short press SB1) or
made.
FEATURES
decreasing (short pressing SB2) until you get
the desired value or,
PROGRAMMING VALUES EXAMPLE
• Turn OFF the radio and start-over.
Example of Programming a Frequency
5. I just programmed the value I wanted.
Assuming current frequency value is set to
How do I exit Programming Mode? Channel 1, with the UHF default frequency ‘02’
• If you are in Programming Mode you can exit by (equivalent to 464.5500 MHz), and you want to
long pressing the PTT button twice. change it to Frequency Number = ‘13’ (which is
• If you are already in the ‘Idle’ Programming mapped to 461.1375 MHz), follow this
Mode, long press the PTT button once. sequence:
• Enter Programming Mode
41
English
• Short press the PTT button to enter Frequency Example of Programming a Code
Programming Selection Mode. Radio will
Assuming current code value is set to factory
announce current value ‘2’
default ‘001’, and you want to change it to
• Press SB1 button eleven times to scroll up the CTCSS/DPL Code = 103 follow the sequence
frequency list and you will hear frequency "13" below:
• Long press the PTT button. LED Indicator will • Enter into Advanced Configuration Mode
show a green heartbeat to indicate 'Idle' state.
• Short press the PTT button twice and you will
• Long press the PTT button to exit Programming hear "Code #" (Entering CTCSS/DPL
PROGRAMMING
42
English
Example of Programming Auto-Scan Example of Programming Active Channels
Auto-Scan is the third Programming Mode Active Channels is the last Programming Mode and
and can be set to either ON or OFF on a It allows you to modify the number of active channels
particular channel. the radio will be programmed to support.
PROGRAMMING
Active Channels Programming Selection Mode.
Auto-Scan Programming Selection Mode. The
FEATURES
• The radio will announce "Active Channels" and
radio will announce "Auto-Scan" and current
current value.
setting (Enabled or Disabled).
• Short press the SB1 or SB2 buttons until you
• Short press the SB1 or SB2 buttons to
hear the number of channels desired.
toggle Enabled/Disabled for the Auto-Scan
feature on the selected channel. • Long press the PTT button. LED Indicator will
show a green heartbeat to indicate “Idle” state.
• Long press the PTT button. LED Indicator will
show a green heartbeat to indicate “Idle” state. • Long press the PTT button to exit
Programming Mode or turn radio OFF.
• Long press the PTT button to exit
Programming Mode or turn radio OFF.
43
English
OTHER PROGRAMMING FEATURES • To stop scanning, short press the SBx
button again.
Scan
• By pressing the PTT button while the radio is
Scan allows you to monitor other channels to detect
scanning, the radio will transmit on the channel
conversations. When the radio detects a
which was selected before Scan was activated.
transmission, it will stop scanning and will receive on
If no transmission occurs within five seconds,
the active channel. This will allow you to listen and
scanning will resume.
talk to people on that channel without having to
change channel. If there is are transmissions on • If you want to scan a channel without
another channel once the radio has stopped Interference Eliminator Codes (CTCSS/DPL),
PROGRAMMING
scanning then you will not hear that activity. After set the code settings for the channels to ‘0’ in the
FEATURES
activity has ceased on the channel which the radio CTCSS/DPL Programming Selection Mode.
has stopped, scanning will resume again after 5
seconds of no activity on that channel.
Whenever the radio is set up in Scan, the LED
• To start scanning, press the SBx (x=1 or 2)
Indicator will signal a Red blink.
button (Scan has to be programmed to either
SB1 or SB2 via CPS). SB2 default is Scan/
Nuisance delete,
44
English
Editing Scan List To delete a channel from the Scan List:
Scan Lists can be edited by using the CPS • To start scanning, press the SBx (x=1 or
(refer to CPS section on page 46) 2) button (Scan has to be programmed to
either SB1 or SB2 via CPS). SB2 default
Nuisance Channel Delete • is Scan/Nuisance delete,
Nuisance Channel Delete allows you to
Wait until the radio stops on the channel
temporarily remove channels from the Scan
you wish to eliminate, then long press the
List. This feature is useful when frequent, •
SBx button to delete it.
irrelevant conversations on a channel tie up
The channel will not be scanned again
PROGRAMMING
the scanning feature, becoming a nuisance
until you exit Scan by short pressing the
FEATURES
to the user.
SBx button again or by turning the radio
OFF and back ON.
45
English
CPS (COMPUTER PROGRAMMING To program, connect the RM Series radio
SOFTWARE) via the Drop-in Charger Tray and CPS
Programming Cable as shown in the picture
above.
CPS allows the user to program frequencies,
PL/DPL codes, as well as other features such
as: Bandwidth Select, Time-out Timer, Power
Select, Scan List, Call Tones, Scramble,
PROGRAMMING
46
English
Bandwidth Select (Only Canada models) Power Select
All US models are compliants with the Power Select allows you to select between
narrowbandwith FCC regulation. high and low transmission power per channel.
The power levels for RM Series toggle
Default setting for Bandwidth Select depends between 2W and 1W.
on the specific frequency and channel. Some
Call Tones
frequencies have selectable channel spacing,
which must match with other radios for Call Tones feature allows you to transmit an
optimum audio quality. audible tone to other radios on the same
channel and alerting them that you are about
PROGRAMMING
For details, refer to Frequency and Code
to talk or alerting them
FEATURES
Charts section.
without speaking. The call tones feature must
Time-Out Timer be programmed to SB1 or SB2 and 1 of 3 pre-
When pressing the PTT button, transmissions recorded tones selected
will be terminated after a preset time of Reverse Burst
continuous transmitting. The default setting Reverse Burst eliminates unwanted noise
is 60 sec and can be changed using the CPS. (squelch tail) during loss of carrier detection.
Scramble You can select values of either 180 or 240 to
be compatible with other radios. Default is
The Scramble feature makes transmissions 180.
sound garbled to anyone listening without the
Notes: Some of the features available with the CPS
same code. Scramble default value is OFF.
software may vary depending on the radio
The Scramble feature must be programmed model.
to SB1 or SB2.
47
English
CLONING RADIOS or copied from) and
You can clone RM Series radio profiles from • a Target radio (the radio which profile will be
one Source radio to a Target radio by using any cloned from the source radio.)
one of these 3 methods: The Source radio has to be in Pocket 1 or 4
• Using a Multi Unit Charger (MUC - optional while the Target radio has to be in Pocket 2 or
accessory), 5, matching in the MUCs pockets by pairs as
• Two Single Unit Chargers (SUC) and a Radio-to- follows:
Radio cloning cable (optional accessory),
• 1 and 2 or,
• the CPS (free software download) and CPS
PROGRAMMING
programming cable ((optional accessory). • 4 and 5
FEATURES
Cloning with a Multi Unit Charger (MUC)
When cloning, the MUC does not need to be
plugged into a power source, but ALL radios
require charged batteries.
1. Turn ON the Target radio and place it into one of
the MUC Target Pockets
2. Power the Source radio following the sequence
below:
To clone radios using the MUC, there must be • Long press the PTT button and SB2
at least two radios: simultaneously while turning the radio ON.
49
English
• Wait for 3 seconds before releasing the When ordering the MUC, please refer
buttons until a distinctive audible tone is to P/N PMLN6384A.
heard and ‘Cloning’ is announced. Notes:
3. Place the Source radio in the source pocket
• Paired Target radios and Source radios must
that pairs with the target pocket you chose in
be of the same band type in order for the
step 1. ress ̀ and release SB1 on Source
cloning to run successfully.
radio.
After cloning is completed, the Source radio will a • MUC pockets numbers should be read from
4.
nnounce either ‘Successful’ (cloning wa left to right with the Motorola logo facing front.
PROGRAMMING
50
English
CPS and Cloning Cables (Optionals) CPS Cable
• Both CPS and Cloning cables are made to
work either with RM Series radios or RDX
series. Cloning cable also can work with a
mix of RDX and RM radios.
• The CPS cable is made to program RM Cloning Cable
series radio when the switch is in "Flash"
position. If you want to use the CPS cable
PROGRAMMING
to program an RDX radio, make sure the
FEATURES
switch is in "CPS" position and attach a
USB convertor provided as part of the CPS
Micro-to-Mini USB Convertor
cable kit.
51
English
Cloning Radio using the Radio to Radio 2. Unplug any cables (power supply or USB
(R2R) Cloning Cable (Optional Accessory) cables) from the SUCs.
3. Plug one side of the cloning cable mini
connector to one SUC. Plug the other end to
the second SUC.
Note: During the cloning process no power is
being applied to the SUC. The batteries will
not be charged. A data communication is
being established between the two radios.
PROGRAMMING
4. Turn ON the Target radio and place it into one of
FEATURES
the SUCs.
5. On the Source radio, power the radio following
Operating Instructions the sequence below:
• Long press the PTT button and SB2
1. Before beginning the cloning process, make
simultaneously while turning the radio
sure you have:
ON.
• A fully charged battery on each one of
• Wait for 3 seconds before releasing the
the radios.
buttons until you hear a distinctive
• Two Single Unit Chargers (SUC).
audible tone and the word "Cloning"
Either 2 SUC for RM Series or 1 SUC
for RM Series and 1 SUC for RDX 6. Place the Source radio in its SUC, press and
Series release SB1.
• Turn OFF the radios and,
51
English
7. After cloning is completed, the Source radio will 3. Ensure that the battery is engaged properly on
announce either ‘pass’ (cloning was to the radio.
successful) or ‘fail’ (cloning process has 4. Ensure that there is no debris in the charging
failed). If the Source radio is a display model, it tray or on the radio contacts.
will either show ‘Pass’ or ‘Fail’ on the display (a
5. Ensure that the Target radio is turned ON.
tone will be heard within 5 seconds).
6. Ensure that the Source radio is in cloning mode.
7. Ensure that radios are both from the same
frequency band, same region and same
8.
PROGRAMMING
52
English
Cloning using the CPS (Computer
Programming Software)
When cloning using this method, you will need
to have the CPS software, a Drop-in Tray
Charger and the CPS Programming Cable.
To order the CPS Programming
Cable, please refer to HKKN4028A
PROGRAMMING
available either in:
FEATURES
• the CPS Help File --> Content and Index -->
Cloning Radios, or
• in the CPS Programming Cable Accessory
Leaflet.
53
English
TROUBLESHOOTING
Scramble Code might be ON, and/or setting does not match the other radios'
Message Scrambled
settings.
54
English
Symptom Try This...
Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease
range. Check for clear line of sight to improve transmission.
Wearing radio close to body such as in a pocket or on a belt decreases range.
Change location of radio. To increase range and coverage, you can reduce
Limited talk range obstructions, increase power. UHF radios provides greater coverage in
industrial and commercial buildings. Increasing power provides greater signal
range and increased penetration through obstructions.
Refer to See “Talking and Monitoring” on page 27.
TROUBLESHOOTING
Message not transmitted or Recharge, replace and/or reposition batteries. Refer to “About your Li-Ion
received Battery” section on page 14.
Obstructions and operating indoors, or in vehicles, may interfere. Change
location. Refer to “Talking and Monitoring” Section on page 27.
Verify that the radio is not in Scan. Refer to “Scan” on page 44 and “Nuisance
Channel Delete” on page 45.
55
English
Symptom Try This...
Radios are too close; they must be at least five feet apart.
Heavy static or interference Radios are too far apart or obstacles are interfering with transmission.
Refer to “Talking and Monitoring” on page 27.
Check that the radio/battery is properly inserted and check the battery/charger
contacts to ensure that they are clean and charging pin is inserted correctly.
Drop-in Charger LED light
Refer to “Charging the Battery” section on page 21, “Drop-in Tray Charger LED
does not blink
Indicators” section on page 24 and “Installing the Lithium-Ion Battery” section
on page 16.
TROUBLESHOOTING
56
English
Symptom Try This...
VOX feature might be set to OFF.
Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’.
Cannot activate VOX
Accessory not working or not compatible.
Refer to “Hands-Free Use/VOX” section on page 31.
Check drop-in tray charger is properly connected and correspond to a
compatible power supply.
Ensure that you have the drop-in tray charger adjustable piece placed on the
Battery does not charge
right position.
although it has been placed in
Refer to “Charging with the Drop-In Tray Single Unit Charger” section on
the drop-in charger for a while
page 21 and “Charging a Standalone Battery” section on page 22.
Check the charger’s LEDs indicators to see if the battery has a problem. Refer
to “Drop-in Tray Charger LED Indicators” section on page 24.
Note: Whenever a feature in the radio seems to not correspond to the default or preprogrammed values, check
TROUBLESHOOTING
to see if the radio has been programmed using the CPS with a customized profile.
57
English
USE AND CARE
USE AND CARE
Turn radio OFF and Dry with soft cloth Do not use radio until
remove batteries completely dry
58
English
FREQUENCY AND CODE CHARTS
RMU2043 - UHF DEFAULT FREQUENCIES CHART
Frequency
Channel Frequency # Code # Code Bandwidth
59
English
RMU2040 - UHF DEFAULT FREQUENCIES CHART
60
English
RMM2050 - MURS DEFAULT FREQUENCIES CHART
61
English
PL/DPL Codes
DPL Code DPL Code DPL Code
39 23 55 116 71 243
40 25 56 125 72 244
41 26 57 131 73 245
FREQUENCY AND CODE
42 31 58 132 74 251
43 32 59 134 75 261
44 43 60 143 76 263
45 47 61 152 77 265
46 51 62 155 78 271
47 54 63 156 79 306
48 65 64 162 80 311
49 71 65 165 81 315
50 72 66 172 82 331
51 73 67 174 83 343
52 74 68 205 84 346
53 114 69 223 85 351
54 115 70 226 86 364
62
English
PL/DPL Codes (Continued)
DPL Code DPL Code DPL Code
87 365 104 565 121 754
88 371 105 606 123 645
89 411 106 612 124 Customized PL
90 412 107 624 125 Customized PL
63
English
PL/DPL Codes (Continued)
DPL Code DPL Code DPL Code
139 Inverted DPL 48 156 Inverted DPL 65 173 Inverted DPL 82
140 Inverted DPL 49 157 Inverted DPL 66 174 Inverted DPL 83
141 Inverted DPL 50 158 Inverted DPL 67 175 Inverted DPL 84
142 Inverted DPL 51 159 Inverted DPL 68 176 Inverted DPL 85
FREQUENCY AND CODE
64
English
PL/DPL Codes (Continued)
DPL Code DPL Code DPL Code
190 Inverted DPL 99 200 Inverted DPL 109 210 Inverted DPL 119
191 Inverted DPL 100 201 Inverted DPL 110 211 Inverted DPL 120
192 Inverted DPL 101 202 Inverted DPL 111 212 Inverted DPL 121
193 Inverted DPL 102 203 Inverted DPL 112 213 Inverted DPL 123
65
English
Products and Accessories
MOTOROLA LIMITED
WARRANTY FOR THE Products Covered Length of Coverage
UNITED STATES AND
CANADA Products and
Accessories as defined
One (1) year from the date
of purchase by the first
consumer purchaser of the
above, unless otherwise
What Does this Warranty Cover? provided for below.
product unless otherwise
provided for below.
Subject to the exclusions contained below,
Motorola, Inc. warrants its telephones, pagers, and Decorative
consumer and business two-way radios (excluding Accessories and Limited lifetime warranty
Cases. for the lifetime of ownership
commercial, government or industrial radios) that Decorative covers, by the first consumer
operate via Family Radio Service or General bezels, PhoneWrap™ purchaser of the product.
Mobile Radio Service, Motorola-branded or covers and cases.
WARRANTY
Products and warranty or for ninety (90)
the period(s) outlined below. Accessories that are days from the date returned
This limited warranty is a consumer's exclusive Repaired or Replaced. to the consumer, whichever
is longer.
remedy, and applies as follows to new Motorola
Products, Accessories and Software purchased by
consumers in the United States, which are
accompanied by this written warranty.
67
English
Exclusions Use of Non-Motorola Products and
Normal Wear and Tear. Periodic maintenance, Accessories. Defects or damage that result from
repair and replacement of parts due to normal the use of Non-Motorola branded or certified
wear and tear are excluded from coverage. Products, Accessories, Software or other
peripheral equipment are excluded from coverage.
Batteries. Only batteries whose fully charged
capacity falls below 80% of their rated capacity Unauthorized Service or Modification. Defects
and batteries that leak are covered by this limited or damages resulting from service, testing,
warranty. adjustment, installation, maintenance, alteration,
or modification in any way by someone other than
Abuse & Misuse. Defects or damage that result
Motorola, or its authorized service centers, are
from: (a) improper operation, storage, misuse or
excluded from coverage.
abuse, accident or neglect, such as physical
damage (cracks, scratches, etc.) to the surface of Altered Products. Products or Accessories with
the product resulting from misuse; (b) contact with (a) serial numbers or date tags that have been
liquid, water, rain, extreme humidity or heavy removed, altered or obliterated; (b) broken seals
perspiration, sand, dirt or the like, extreme heat, or or that show evidence of tampering; (c)
food; (c) use of the Products or Accessories for mismatched board serial numbers; or (d)
commercial purposes or subjecting the Product or nonconforming or non-Motorola housings, or
Accessory to abnormal usage or conditions; or (d) parts, are excluded form coverage.
WARRANTY
68
English
Communication Services. Defects, damages, or Software NOT Embodied in Physical Media.
the failure of Products, Accessories or Software Software that is not embodied in physical media
due to any communication service or signal you (e.g. software that is downloaded from the
may subscribe to or use with the Products internet), is provided “as is” and without warranty.
Accessories or Software is excluded from
WHO IS COVERED?
coverage.
This warranty extends only to the first consumer
Software purchaser, and is not transferable.
WARRANTY
warranty is made that the software will meet your
copyrighted software, such as the exclusive rights
requirements or will work in combination with any
to distribute or reproduce the copyrighted
hardware or software applications provided by
software. Accordingly, any copyrighted software
third parties, that the operation of the software
contained in the Motorola products may not be
products will be uninterrupted or error free, or that
modified, reverse-engineered, distributed, or
all defects in the software products will be
reproduced in any manner to the extent allowed by
corrected.
law.
69
English
Furthermore, the purchase of the Motorola EXPORT LAW ASSURANCES
products shall not be deemed to grant either
This product is controlled under the export
directly or by implication, estoppel, or otherwise,
regulations of the United States of America. The
any license under the copyrights, patents, or
Governments of the United States of America may
patent applications of Motorola or any third party
restrict the exportation or re-exportation of this
software provider, except for the normal, non-
product to certain destinations. For further
exclusive, royalty-free license to use that arises by
information contact the U.S. Department of
operation of law in the sale of a product.
Commerce.
PATENT NOTICE
This product is covered by one or more of the
following United States patents.
5896277 5894292 5864752 5699006 5742484
D408396 D399821 D387758 D389158 5894592
5893027 5789098 5734975 5861850 D395882
D383745 D389827 D389139 5929825 5926514
5953640 6071640 D413022 D416252 D416893
D433001
WARRANTY
70
English
ACCESSORIES
ACCESSORIES
AUDIO ACCESSORIES BATTERY
71
English
CABLES Carrying
ACCESSORIES
Part No. Description Part No. Description
CHARGERS
72
English
m
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks
or registered trademarks of Motorola Trademark Holdings, LLC and are used under
license. All other trademarks are the property of their respective owners. ©2013 Motorola,
Inc. All rights reserved. Printed in Malaysia.
Motorola Solutions, Inc. 1301 East Algonquin Road Schaumburg, Illinois 60196, 68012009071
U.S.A. 800-367-2346 motorolasolutions.com