Professional Documents
Culture Documents
Bosch Rexroth Axial Piston Fixed Motor A2FM Re91001 PDF
Bosch Rexroth Axial Piston Fixed Motor A2FM Re91001 PDF
2012
Replaces: 09.07
1/46
A2FM
Data sheet
Series 6
Size Nominal pressure/Maximum pressure
5 315/350 bar
10 to 200 400/450 bar
250 to 1000 350/400 bar
Open and closed circuits
Contents Features
Ordering code for standard program 2 –– Fixed motor with axial tapered piston rotary group of bent-
axis design, for hydrostatic drives in open and closed circuits
Technical data 4
–– For use in mobile and stationary applications
Dimensions 11
–– The output speed is dependent on the flow of the pump and
Flushing and boost pressure valve 34
the displacement of the motor.
Pressure-relief valve 36
–– The output torque increases with the pressure differential
Counterbalance valve BVD and BVE 38 between the high-pressure and the low-pressure side.
Speed sensors 42 –– Finely graduated sizes permit far-reaching adaptation to the
drive case
Installation instructions 44
–– High power density
General instructions 46
–– Small dimensions
–– High total efficiency
–– Good starting characteristics
–– Economical design
–– One-piece tapered piston with piston rings for sealing
2/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
Hydraulic fluid
Mineral oil and HFD. HFD for sizes 250 to 1000 only in combination with long-life bearings "L" (without code)
01 HFB, HFC hydraulic fluid Sizes 5 to 200 (without code)
Sizes 250 to 1000 (only in combination with long-life bearings "L") E-
Operating mode
04 Motor (plug-in motor A2FE, see RE 91008) M
Size (NG)
Geometric displacement, see table of values on page 7
05
5 10 12 16 23 28 32 45 56 63 80 90 107 125 160 180 200 250 355 500 710 1000
Series
06 6
Index
NG10 to 180 1
07 NG200 3
NG5 and 250 to 1000 0
Direction of rotation
08 Viewed on drive shaft, bidirectional W
Seals
09 FKM (fluor-caoutchouc) V
1) Conical shaft with threaded pin and woodruff key (DIN 6888). The torque must be transmitted via the tapered press fit.
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 3/46
Port plates for service lines2) 5 10-16 23 28, 32 45 56,63 80,90 107-125 160-180 200 250 355-500 1000
SAE flange ports 01 0 – – 010
A and B at rear 7 – – – – – – – – – – – – 017
SAE flange ports 02 0 – – – – – 020
A and B at side, opposite 7 – – – – ▲ ▲ – – – 027
9 – – – – – – – – – – – 029
Threaded ports A and B 03
0 – – – – – – – – – 030
at side, opposite
Threaded ports A and B 04
0 – – – – – m – – 040
at side and rear3)
SAE flange ports 10
0 – – – – – m – 100
A and B at bottom (same side)
Port plate BVD 17 – – – – – – – – 171
12 with 1-level pressure- 1 178
relief valves for mounting a 18 8 – – – – – – – 181
counterbalance valve5) BVE 18 – – – – – – – – –4) – – 188
Port plate with 19 1 – – – – – – – 191
pressure-relief valves 2 – – – – – – – 192
Speed sensors (see pages 42 and 43) 5 to 16 23 to 180 200 250 to 500 710 to 10004)
Without speed sensor (without code)
Prepared for HDD speed sensor – ▲ ▲ – F
13 HDD speed sensor mounted7) – ▲ ▲ – H
Prepared for DSA speed sensor – m m m – U
DSA speed sensor mounted7) – m m m – V
Special version
Standard version (without code)
14
Special version for slew drives (standard with port plate 19) J
= Available m = On request – = Not available ▲ = Not for new projects = Preferred program
Technical data
Hydraulic fluid Details regarding the choice of hydraulic fluid
Before starting project planning, please refer to our data The correct choice of hydraulic fluid requires knowledge of the
sheets RE 90220 (mineral oil), RE 90221 (environmentally operating temperature in relation to the ambient temperature: in
acceptable hydraulic fluids), RE 90222 (HFD hydraulic fluids) a closed circuit, the circuit temperature, in an open circuit, the
and RE 90223 (HFA, HFB, HFC hydraulic fluids) for detailed reservoir temperature.
information regarding the choice of hydraulic fluid and applica- The hydraulic fluid should be chosen so that the operating
tion conditions. viscosity in the operating temperature range is within the
The fixed motor A2FM is not suitable for operation with HFA optimum range (νopt see shaded area of the selection diagram).
hydraulic fluid. If HFB, HFC or HFD or environmentally accept- We recommended that the higher viscosity class be selected
able hydraulic fluids are used, the limitations regarding technical in each case.
data or other seals must be observed. Example: At an ambient temperature of X °C, an operating tem-
perature of 60 °C is set in the circuit. In the optimum operating
Selection diagram viscosity range (νopt., shaded area), this corresponds to the
-40° -20° 0° 20° 40° 60° 80° 100° viscosity classes VG 46 or VG 68; to be selected: VG 68.
1600 1600
1000
600 Note
400 The case drain temperature, which is affected by pressure and
200 speed, can be higher than the circuit temperature or reservoir
VG 68
VG
VG 32
VG 46
VG 2
100
0
Viscosity ν [mm2/s]
5 5
-40° -25° -10° 0° 10° 30° 50° 70° 90° 115°
Temperature t [°C]
tmin = -40°C Hydraulic fluid temperature range tmax = +115°C
Technical data
Filtration of the hydraulic fluid Sizes 250 to 1000
Permissible pressure loading The values are valid for an ambient pressure pabs = 1 bar.
The service life of the shaft seal is influenced by the speed of Temperature range
the axial piston unit and the case drain pressure (case pres- The FKM shaft seal may be used for case drain temperatures
sure). The mean differential pressure of 2 bar between the from -25 °C to +115 °C.
case and the ambient pressure may not be enduringly exceed-
ed at normal operating temperature. For a higher differential Note
pressure at reduced speed, see diagram. Momentary pressure For application cases below -25 °C, an NBR shaft seal is
spikes (t < 0.1 s) of up to 10 bar are permitted. The service life required (permissible temperature range: -40 °C to +90 °C).
of the shaft seal decreases with an increase in the frequency of State NBR shaft seal in plain text when ordering.
pressure spikes. Please contact us.
Technical data
Operating pressure range Minimum pressure – pump mode (inlet)
(operating with mineral oil) To prevent damage to the axial piston motor in pump operating
mode (change of high-pressure side with unchanged direction
Pressure at service line port A or B of rotation, e. g. when braking), a minimum pressure must be
guaranteed at the service line port (inlet). The minimum pres-
Size 5 sure depends on the speed of the axial piston unit (see charac-
teristic curve below).
Nominal pressure pnom___________________ 315 bar absolute
12
Maximum pressure pmax_________________ 350 bar absolute
Single operating period______________________________ 10 s
6
Sizes 10 to 200
Nominal pressure pnom__________________ 400 bar absolute 4
Sizes 250 to 1000 This diagram is valid only for the optimum viscosity range from
nopt = 36 to 16 mm2/s.
Nominal pressure pnom__________________ 350 bar absolute Please contact us if these conditions cannot be satisfied.
Maximum pressure pmax_________________ 400 bar absolute Definition
Single operating period______________________________ 10 s
Total operating period______________________________ 300 h Nominal pressure pnom
The nominal pressure corresponds to the maximum design
Summation pressure (pressure A + pressure B) pSu __ 700 bar pressure.
Minimum pressure (high-pressure side) ____25 bar absolute Maximum pressure pmax
The maximum pressure corresponds to the maximum operat-
Rate of pressure change RA max ing pressure within the single operating period. The sum of the
with integrated pressure-relief valve_____________ 9000 bar/s single operating periods must not exceed the total operating
without pressure-relief valve___________________ 16000 bar/s period.
Minimum pressure (high-pressure side)
pnom
Minimum pressure at the high-pressure side (A or B) which is
Dt required in order to prevent damage to the axial piston unit.
Summation pressure pSu
Pressure p
Time t
Total operating period = t1 + t2 + ... + tn
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 7/46
Technical data
Table of values (theoretical values, without efficiency and tolerances; values rounded)
Size NG 5 10 12 16 23 28 32 45 56 63 80
Displacement geometric, Vg cm3 4.93 10.3 12 16 22.9 28.1 32 45.6 56.1 63 80.4
per revolution
Speed maximum1) nnom rpm 10000 8000 8000 8000 6300 6300 6300 5600 5000 5000 4500
nmax 2) rpm 11000 8800 8800 8800 6900 6900 6900 6200 5500 5500 5000
Input flow3)
at nnom and Vg qV L/min 49 82 96 128 144 177 202 255 281 315 362
Torque4)
at Vg and Δp = 350 bar T Nm 24.75) 57 67 89 128 157 178 254 313 351 448
Δp = 400 bar T Nm – 66 76 102 146 179 204 290 357 401 512
Rotary stiffness c kNm/rad 0.63 0.92 1.25 1.59 2.56 2.93 3.12 4.18 5.94 6.25 8.73
Moment of inertia for JGR kgm2 0.00006 0.0004 0.0004 0.0004 0.0012 0.0012 0.0012 0.0024 0.0042 0.0042 0.0072
rotary group
Maximum angular a rad/s2 5000 5000 5000 5000 6500 6500 6500 14600 7500 7500 6000
acceleration
Case volume V L 0.17 0.17 0.17 0.20 0.20 0.20 0.33 0.45 0.45 0.55
Mass (approx.) m kg 2.5 5.4 5.4 5.4 9.5 9.5 9.5 13.5 18 18 23
Size NG 90 107 125 160 180 200 250 355 500 710 1000
Displacement geometric, Vg cm3
90 106.7 125 160.4 180 200 250 355 500 710 1000
per revolution
Speed maximum1) nnom rpm 4500 4000 4000 3600 3600 2750 2700 2240 2000 1600 1600
nmax 2) rpm 5000 4400 4400 4000 4000 3000 – – – – –
Input flow3)
at nnom and Vg qV L/min 405 427 500 577 648 550 675 795 1000 1136 1600
Torque4)
at Vg and Δp = 350 bar T Nm 501 594 696 893 1003 1114 1393 1978 2785 3955 5570
Δp = 400 bar T Nm 573 679 796 1021 1146 1273 – – – – –
Rotary stiffness c kNm/rad 9.14 11.2 11.9 17.4 18.2 57.3 73.1 96.1 144 270 324
Moment of inertia for JGR kgm2 0.0072 0.0116 0.0116 0.0220 0.0220 0.0353 0.061 0.102 0.178 0.55 0.55
rotary group
Maximum angular a rad/s2 6000 4500 4500 3500 3500 11000 10000 8300 5500 4300 4500
acceleration
Case volume V L 0.55 0.8 0.8 1.1 1.1 2.7 2.5 3.5 4.2 8 8
Mass (approx.) m kg 23 32 32 45 45 66 73 110 155 325 336
Technical data
Permissible radial and axial forces of the drive shafts
(splined shaft and parallel keyed shaft)
Size NG 5 53) 10 10 12 12 16 23 23
Drive shaft ø mm 12 12 20 25 20 25 25 25 30
Maximum Fq Fq max kN 1.6 1.6 3.0 3.2 3.0 3.2 3.2 5.7 5.4
radial force1)
at distance a a mm 12 12 16 16 16 16 16 16 16
(from shaft collar) a
with permissible torque Tmax Nm 24.7 24.7 66 66 76 76 102 146 146
≙ permissible pressure Δp Δp perm bar 315 315 400 400 400 400 400 400 400
Maximum axial force2) +Fax max N 180 180 320 320 320 320 320 500 500
Fax+
– –Fax max N 0 0 0 0 0 0 0 0 0
Permissible axial force per bar operating pressure ±Fax perm/bar N/bar 1.5 1.5 3.0 3.0 3.0 3.0 3.0 5.2 5.2
Size NG 28 28 32 45 56 564) 56 63 80
Drive shaft ø mm 25 30 30 30 30 30 35 35 35
Maximum Fq Fq max kN 5.7 5.4 5.4 7.6 9.5 7.8 9.1 9.1 11.6
radial force1)
at distance a a mm 16 16 16 18 18 18 18 18 20
(from shaft collar) a
with permissible torque Tmax Nm 179 179 204 290 357 294 357 401 512
≙ permissible pressure Δp Δp perm bar 400 400 400 400 400 330 400 400 400
Maximum axial force2) +Fax max N 500 500 500 630 800 800 800 800 1000
Fax+
– –Fax max N 0 0 0 0 0 0 0 0 0
Permissible axial force per bar operating pressure ±Fax perm/bar N/bar 5.2 5.2 5.2 7.0 8.7 8.7 8.7 8.7 10.6
Permissible axial force per bar operating pressure ±Fax perm/bar N/bar 10.6 10.6 10.6 12.9 12.9 12.9 16.7 16.7 16.7
Maximum axial force2) +Fax max N 1600 2000 2500 3000 4400 4400
Fax+
– –Fax max N 0 0 0 0 0 0
Permissible axial force per bar operating pressure ±Fax perm/bar N/bar 16.7 5) 5) 5) 5) 5)
1) With intermittent operation 6) When at a standstill or when axial piston unit operating in
2) Maximum permissible axial force during standstill or when non-pressurized conditions. Higher forces are permissible
the axial piston unit is operating in non-pressurized condi- when under pressure, please contact us.
tion. Note
3) Conical shaft with threaded pin and woodruff key (DIN 6888) Influence of the direction of the permissible axial force:
4) Restricted technical data only for splined shaft +Fax max = Increase in service life of bearings
5) Please contact us. –Fax max = Reduction in service life of bearings (avoid)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 9/46
Technical data
Effect of radial force Fq on the service life of bearings Determining the operating characteristics
By selecting a suitable direction of radial force Fq, the load on Vg • n
the bearings, caused by the internal rotary group forces can be Input flow qv = [L/min]
reduced, thus optimizing the service life of the bearings. Rec- 1000 • ηv
ommended position of mating gear is dependent on direction
qV • 1000 • ηv
of rotation. Examples: Speed n = [min-1]
Vg
Toothed gear drive V-belt output
NG ϕopt ϕopt Vg • Δp • ηmh
Torque T = [Nm]
5 to 180 ± 70° ± 45° 20 • π
200 to 1000 ± 45° ± 70°
2π•T•n qv • Δp • ηt
Power P = = [kW]
Alternating 60000 600
direction of rotation
t o
op pt
Vg = Displacement per revolution in cm3
t
op
Δp = Differential pressure in bar
op t
n = Speed in rpm
ηv = Volumetric efficiency
ηmh = Mechanical-hydraulic efficiency
Clockwise
"Counter-clockwise" "Counter-clockwise"
direction
direction of rotation direction of rotation
of rotation
Pressure at Pressure at Pressure at
port B port A port B
10/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 11/46
Y
521) 24
View Y
10 45° 45°
T1, T2 T2
A
ø60 -0.046
56
70
25°
75
6.4
48.5
62
70
T1
4 8
61
B, A
B
51 80
Drive shafts
B Parallel keyed shaft C Conical shaft with threaded pin and woodruff key, 3x5
DIN 6885, A4x4x20 (DIN 6888), (tapering 1:10)
M10 x 13)5)
10
ø12 +0.001
+0.012
M4 x 0.72)3)
3.2
ø12.8
4
13.5
ø15
7.3
ø15
9.5
24
10.5
22.5
Ports
Designation Port for Standard6) Size3) Maximum pressure [bar]4) State7)
A, B Service line DIN 3852 M18 x 1.5; 12 deep 350 O
T1 Drain line DIN 3852 M10 x 1; 8 deep 3 O
T2 Drain line DIN 3852 M10 x 1; 8 deep 3 O
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Thread according to DIN 3852, maximum tightening torque: 30 Nm
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
12/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
Dimensions sizes 10, 12, 16 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
45°
45°
201) 95
6 95
T1
29
ø80–0.019
40°
95
0
10
54
9
18.2 12
60 A B
5
T2
ø8
Flange
similar to ISO 3019-2
Drive shafts
Sizes 10, 12, 16 Sizes 10, 12 Sizes 10, 12, 16 Sizes 10, 12
A Splined shaft DIN 5480 Z Splined shaft DIN 5480 B Parallel keyed shaft P Parallel keyed shaft
W25x1.25x18x9g W20x1.25x14x9g DIN 6885, AS8x7x32 DIN 6885, AS6x6x32
22 16 22 16
M10x1.52)3)
ø25+0.002
ø20+0.002
+0.015
+0.015
Key Key
M10x1.52)3)
7.5 5 7.5 5
M6x12)3)
22.5
ø28
ø28
ø28
28
22 22 40 40
28 34
Ports
Designation Port for Standard Size3) Maximum pressure [bar]4) State7)
A, B Service line (see port plates) 450
T1 Drain line DIN 38526) M12 x 1.5; 12 deep 3 X5)
T2 Drain line DIN 38526) M12 x 1.5; 12 deep 3 O5)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 13/46
Dimensions sizes 10, 12, 16 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
Detail Y Detail Y
34
B A
56
56
69
B A
91
91
131 131
166 Y 85 147 85
Y
166 95
Dimensions sizes 23, 28, 32 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
45°
45°
251) 106
118
8
T1
ø100–0.022
40°
25
118
5
12
56
11
23.2 18
42 T2 A B
06
ø1
Flange
ISO 3019-2
Drive shafts
Sizes 23, 28, 32 Sizes 23, 28 Sizes 23, 28, 32 Sizes 23, 28
A Splined shaft DIN 5480 Z Splined shaft DIN 5480 B Parallel keyed shaft P Parallel keyed shaft
W30x2x14x9g W25x1.25x18x9g DIN 6885, AS8x7x40 DIN 6885, AS8x7x40
22 19 22 19
M10x1.52)3)
ø30+0.002
ø25+0.002
+0.015
+0.015
M8x1.252)3)
Key Key
M8x1.252)3)
M10x1.52)3)
7.5 6 7.5 6
width 8 width 8
ø35
ø35
ø35
33
ø35
28
27 28 50 50
35 43
Ports
Designation Port for Standard Size3) Maximum pressure State7)
[bar]4)
A, B Service line (see port plates) 450
T1 Drain line DIN 38526) M16 x 1.5; 12 deep 3 X5)
T2 Drain line DIN 38526) M16 x 1.5; 12 deep 3 O5)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 15/46
Dimensions sizes 23, 28, 32 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
13 .5
18.2
70
40
78
B A
117
106
144
153 13 120
190 Y
173 Y 59
70
88
70
117
117
B A
144 144
190 120 166 120
Y Y
190 130
40
B
106
91
115
59
13
40.5
158
178
18.2 A
Y
Note
Port plates 18 and 19: see pages 37 and 40
16/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
45°
45°
321) 108
150
12
T1
ø125–0.025
40 °
28
150
0
16
13.5
63
30 20
42 T2 A B
18
ø1
Flange
ISO 3019-2
Drive shafts
Z Splined shaft DIN 5480 P Parallel keyed shaft
W30x2x14x9g DIN 6885, AS8x7x50
28
ø30+0.002
28
M12x1.752)3)
+0.015
Key
M12x1.752)3)
27 60
35
Ports
Designation Port for Standard Size3) Maximum pressure State7)
[bar]4)
A, B Service line (see port plates) 450
T1 Drain line DIN 38526) M18 x 1.5; 12 deep 3 X5)
T2 Drain line DIN 38526) M18 x 1.5; 12 deep 3 O5)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 17/46
23.8
19 .8
80
50
89
B A
122
133
166 19 155 128
194 Y 75 207
Y
04 – Threaded ports at side and rear 10 – SAE flange ports at bottom (same side)
Detail Y Detail Y
58 49
B A B
102
80
100
119
147
133
75
19
50.8
155 169
179 128 193 23.8 A
207 Y 141
Y
Note
Port plates 18 and 19: see pages 37 and 40
18/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
45°
45°
321) 117
150
10
T1
ø125–0.025
31
40 °
150
0
16
13.5
70
30 20
T2 A B
50
28
ø1
Flange
ISO 3019-2
Drive shafts
NG56, 63 NG56 NG56, 63 NG56
A Splined shaft DIN 5480 Z Splined shaft DIN 5480 B Parallel keyed shaft P Parallel keyed shaft
W35x2x16x9g W30x2x14x9g DIN 6885, AS10x8x50 DIN 6885, AS8x7x50
28 28
M12x1.752)3)
28 28
ø35+0.002
M12x1.752)3)
+0.018
ø30+0.002
M12x1.752)3)
M12x1.752)3)
+0.015
Key Key
9.5 9.5 9.5 width 10 9.5 width 8
ø40
ø40
38
ø40
ø40
33
32 27 60 60
40 35
Ports
Designation Port for Standard Size3) Maximum pressure State7)
[bar]4)
A, B Service line (see port plates) 450
T1 Drain line DIN 38526) M18 x 1.5; 12 deep 3 X5)
T2 Drain line DIN 38526) M18 x 1.5; 12 deep 3 O5)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 19/46
19 .8
23.8
87
50
142
96
B A
130
171
182 19 225 Y 136
206 Y 75
04 – Threaded ports at side and rear 10 – SAE flange ports at bottom (same side)
Detail Y Detail Y
58 49
B A B
87
107
107
130
147
142
75
19
50.8
182
171 206 A
195 136 23.8
Y
225 149
Y
Plate Designation Port for Standard Size1) Maximum pressure State5)
[bar]2)
01, 02, A, B Service line SAE J5183) 3/4 in 450 O
10 Fastening thread A/B DIN 13 M10 x 1.5; 17 deep
04 Service line DIN 38524) M33 x 2; 18 deep 450 1x O each
1) Observe the general instructions on page 46 for the maximum tightening torques
2) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
3) Only dimensions according to SAE J518, metric fastening thread is a deviation from standard.
4) The spot face can be deeper than specified in the appropriate standard.
5) O = Must be connected (plugged on delivery)
Note
Port plates 18 and 19: see pages 37 and 40
20/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
45° 45°
321) 132
165
10
T1
ø140–0.025
41
40°
165
0
18
13.5
83
29 20
63 T2 A B
38
ø1
Flange
ISO 3019-2
Drive shafts
NG80, 90 NG80 NG80, 90 NG80
A Splined shaft DIN 5480 Z Splined shaft DIN 5480 B Parallel keyed shaft P Parallel keyed shaft
W40x2x18x9g W35x2x16x9g DIN 6885, AS12x8x56 DIN 6885, AS10x8x56
36 28 36 ø35+0.002 28
ø40+0.002
M12x1.752)3)
M12x1.752)3)
+0.018
+0.018
Key Key
M16x22)3)
M16x22)3)
ø45
ø45
43
38
ø45
ø45
37 32 70 70
45 40
Ports
Designation Port for Standard Size3) Maximum pressure State7)
[bar]4)
A, B Service line (see port plates) 450
T1 Drain line DIN 38526) M18 x 1.5; 12 deep 3 X5)
T2 Drain line DIN 38526) M18 x 1.5; 12 deep 3 O5)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 21/46
27.8
25 2
.
99
57
104
144 B A
162
203 25 196 160
233 Y 84 257 Y
166
25
84
57.2
206 27.8 A
236
Y
Plate Designation Port for Standard Size1) Maximum pressure State4)
[bar]2)
01, 02, A, B Service line SAE J5183) 1 in 450 O
10 Fastening thread A/B DIN 13 M12 x 1.75; 17 deep
1) Observe the general instructions on page 46 for the maximum tightening torques
2) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
3) Only dimensions according to SAE J518, metric fastening thread is a deviation from standard.
4) O = Must be connected (plugged on delivery)
Note
Port plates 18 and 19: see pages 37 and 40
22/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
Dimensions sizes 107, 125 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
45°
45°
T1
ø160–0.025
40
40 °
190
0
20
17.5
85
36.5 23
T2 A B
65
50
ø1
Flange
ISO 3019-2
Drive shafts
NG107, 125 NG107 NG107, 125 NG107
A Splined shaft DIN 5480 Z Splined shaft DIN 5480 B Parallel keyed shaft P Parallel keyed shaft
W45x2x21x9g W40x2x18x9g DIN 6885, AS14x9x63 DIN 6885, AS12x8x63
36 28
M12x1.752)3)
36 28
ø45+0.002
ø40+0.002
M12x1.752)3)
+0.018
+0.018
Key Key
M16x22)3)
12 9.5
M16x22)3)
48.5
ø50
ø50
43
42 37
80 80
50 45
Ports
Designation Port for Standard Size3) Maximum pressure State7)
[bar]4)
A, B Service line (see port plates) 450
T1 Drain line DIN 38526) M18 x 1.5; 12 deep 3 X5)
T2 Drain line DIN 38526) M18 x 1.5; 12 deep 3 O5)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 23/46
Dimensions sizes 107, 125 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
.2
31.8
57
110
25
B A
181
120
159
10 – SAE flange ports at bottom (same side) 02 – SAE flange ports at side, opposite (size 125)
Detail Y
70 Detail Y
B 31
.8
32 7
.
136
66
110
157
B A
194
99
181
32
66.7
226
261 31.8 A 213 178
285 Y
Y
Note
Port plates 17, 18 and 19: see pages 37 and 40
24/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
Dimensions sizes 160, 180 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
45°
45°
T1
ø180–0.025
47
40 °
210
4
22
17.5
96
37.2 25
T2 A B
72
80
ø1
Flange
ISO 3019-2
Drive shafts
NG160, 180 NG160 NG160, 180 NG160
A Splined shaft DIN 5480 Z Splined shaft DIN 5480 B Parallel keyed shaft P Parallel keyed shaft
W50x2x24x9g W45x2x21x9g DIN 6885, AS14x9x70 DIN 6885, AS14x9x70
36 36 36 36
ø50+0.002
Key Key
+0.018
ø45+0.002
+0.018
M16x22)3)
M16x22)3)
M16x22)3)
48.5
ø60
ø60
ø60
ø60
44 42 90 90
55 50
Ports
Designation Port for Standard Size3) Maximum pressure State7)
[bar]4)
A, B Service line (see port plates) 450
T1 Drain line DIN 38526) M22 x 1.5; 14 deep 3 X5)
T2 Drain line DIN 38526) M22 x 1.5; 14 deep 3 O5)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 25/46
Dimensions sizes 160, 180 Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
31.8
32 7
121
.
66
134
B A
188
188
252 32 237
294 Y 99 294 Y 202
Detail Y
70
B
149
185
194
99
32
66.7
252
290 31.8
A
Note
Port plates 18 and 19: see pages 37 and 40
26/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
45 °
45 °
401) 156
9 236
T1
77
ø200–0.029
25°
236
0
25
102.5
84
22
166
Y
32 32 T2 A B
89
Flange
ISO 3019-2 284
306
Detail Y
206
66.7
Drive shafts B A
A Splined shaft DIN 5480 B Parallel keyed shaft
W50x2x24x9g DIN 6885, AS14x9x80
211
36 36 Key
ø50+0.002
+0.018
M16x22)3)
12
M16x22)3)
12 width 14
31.8
32
53.5
ø70
ø70
99
44 100
55
Ports
Designation Port for Standard Size3) Maximum pressure State8)
[bar]4)
A, B Service line SAE J5185) 1 1/4 in 450 O
Fastening thread A/B DIN 13 M14 x 2; 19 deep
T1 Drain line DIN 38527) M22 x 1.5; 14 deep 3 X6)
T2 Drain line DIN 38527) M22 x 1.5; 14 deep 3 O6)
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Only dimensions according to SAE J518, metric fastening thread is a deviation from standard.
6) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
7) The spot face can be deeper than specified in the appropriate standard.
8) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 27/46
Notes
28/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
45°
45°
501) 82
9 22
U T1
124
105
ø224 -0.072
`
30
26°
246
0
28
105
22
0
48 25 T2 ø21
Flange 82
246
ISO 3019-2
Drive shafts
Z Splined shaft DIN 5480 P Parallel keyed shaft
W50x2x24x9g DIN 6885, AS14x9x80
36 36
ø50+0.002
Key
+0.018
22)3)
M16x22)3)
12 12 width 14
M16 x
53.5
ø60
ø60
49 82
58
Ports
Designation Port for Standard Size3) Maximum pressure State7)
[bar]4)
A, B Service line (see port plates) 400
T1 Drain line DIN 38526) M22 x 1.5; 14 deep 3 O5)
T2 Drain line DIN 38526) M22 x 1.5; 14 deep 3 X5)
U Bearing flushing DIN 38526) M14 x 1.5; 12 deep 3 X
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
6) The spot face can be deeper than specified in the appropriate standard.
7) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 29/46
B A 31
31.8
.8
B A
.7
82
93
66
32
172
172
32
100
288 Y 267 Y
314 323
`
22°30
501) 83
14 23.5 °
45
U T1
MA (MB)
171
128
36
0
`
30
ø280 -0.081
26°
335
18
0
32
102
128
198
T2 Y
48 28
83
320 335
350
Flange Detail Y
ISO 3019-2
250
245
Drive shafts 36.6
79.4
W60x2x28x9g DIN 6885, AS18x11x100
42
MB
42 Key
+0.030
M20x2.52)3)
M20x2.52)3)
ø60+0.011
15 15 width 18 MA
ø70
64
ø70
40
71 105 120
82
Ports
Designation Port for Standard Size3) Maximum pressure State8)
[bar]4 )
A, B Service line SAE J5185) 1 1/2 in 400 O
Fastening thread A/B DIN 13 M16 x 2; 21 deep
T1 Drain line DIN 38527) M33 x 2; 18 deep 3 O6)
T2 Drain line DIN 38527) M33 x 2; 18 deep 3 X6)
U Bearing flushing DIN 38527) M14 x 1.5; 12 deep 3 X
MA, M B Measuring operating pressure DIN 38527) M14 x 1.5; 12 deep 400 X
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Only dimensions according to SAE J518, metric fastening thread is a deviation from standard.
6) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
7) The spot face can be deeper than specified in the appropriate standard.
8) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 31/46
`
22°30
501) 98
14 27.5
°
45
U T1
MA (MB)
192
40
142
0
`
30
ø315 -0.081
26°
375
0
112.5
142 36
220
22
48 30 T2 Y
111
Flange 362 375
ISO 3019-2 396
Detail Y
276
270
Drive shafts 36.6
Z Splined shaft DIN 5480 P Parallel keyed shaft
W70x3x22x9g DIN 6885, AS20x12x100 B A
79.4
42 42 MB
+0.030
ø70+0.011
M20x2.52)3)
M20x2.52)3)
Key
15 15 width 20 MA
74.5
ø80
ø80
40
67 105 130
80
Ports
Designation Port for Standard Size3) Maximum pressure State8)
[bar]4)
A, B Service line SAE J5185) 1 1/2 in 400 O
Fastening thread A/B DIN 13 M16 x 2; 21 deep
T1 Drain line DIN 38527) M33 x 2; 18 deep 3 O6)
T2 Drain line DIN 38527) M33 x 2; 18 deep 3 X6)
U Bearing flushing DIN 38527) M18 x 1.5; 12 deep 3 X
MA, M B Measuring operating pressure DIN 38527) M14 x 1.5; 12 deep 400 X
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Only dimensions according to SAE J518, metric fastening thread is a deviation from standard.
6) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
7) The spot face can be deeper than specified in the appropriate standard.
8) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
32/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
`
22°30
501) 131
14 41.5 °
U T1 45
MA (MB)
236
50
183
0
ø400 –0.089
`
30
18°
465
22
102
0
45
183
249
Y
47 35 T2
156
Flange 485 465
ISO 3019-2 507
Detail Y
344
340
Drive shafts 44.5
Z Splined shaft DIN 5480 P Parallel keyed shaft
W90x3x28x9g DIN 6885, AS25x14x125 B A
MB MA
50 50
+0.035
ø90+0.013
Key
96.8
M24x32)3)
18
M24x32)3)
18 width 25
ø100
ø100
95
50
170
91 130
105
Ports
Designation Port for Standard Size3) Maximum pressure State8)
[bar]4)
A, B Service line SAE J5185) 2 in 400 O
Fastening thread A/B DIN 13 M20 x 2.5; 30 deep
T1 Drain line DIN 38527) M42 x 2; 20 deep 3 O6)
T2 Drain line DIN 38527) M42 x 2; 20 deep 3 X6)
U Bearing flushing DIN 38527) M18 x 1.5; 12 deep 3 X
MA, M B Measuring operating pressure DIN 38527) M14 x 1.5; 12 deep 400 X
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Only dimensions according to SAE J518, metric fastening thread is a deviation from standard.
6) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
7) The spot face can be deeper than specified in the appropriate standard.
8) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 33/46
`
22°30
501) 131
14 41.5 °
U T1 45
MA (MB)
236
50
183
0
ø400 –0.089
`
30
26°
465
22
0
143
183 45
277
47 35 T2 Y
156
Flange 468 465
ISO 3019-2 511
Detail Y
344
Drive shafts 340
44.5
Z Splined shaft DIN 5480 P Parallel keyed shaft
W90x3x28x9g DIN 6885, AS25x14x125
B A
50 MB MA
50
+0.035
Key
ø90+0.013
M24x32)3)
18
M24x32)3)
18
96.8
width 25
ø100
ø100
95
50
170
91
130
105
Ports
Designation Port for Standard Size3) Maximum pressure State8)
[bar]4)
A, B Service line SAE J5185) 2 in 400 O
Fastening thread A/B DIN 13 M20 x 2.5; 30 deep
T1 Drain line DIN 38527) M42 x 2; 20 deep 3 O6)
T2 Drain line DIN 38527) M42 x 2; 20 deep 3 X6)
U Bearing flushing DIN 38527) M18 x 1.5; 12 deep 3 X
MA, M B Measuring operating pressure DIN 38527) M14 x 1.5; 12 deep 400 X
1) To shaft collar
2) Center bore according to DIN 332 (thread according to DIN 13)
3) Observe the general instructions on page 46 for the maximum tightening torques.
4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
5) Only dimensions according to SAE J518, metric fastening thread is a deviation from standard.
6) Depending on installation position, T1 or T2 must be connected (see also installation instructions on page 44).
7) The spot face can be deeper than specified in the appropriate standard.
8) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
34/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
Flushing and boost pressure valve Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
The flushing and boost pressure valve is used to remove heat Standard flushing flows
from the hydraulic circuit.
Flushing and boost pressure valve, mounted (code 7)
In an open circuit, it is used only for flushing the housing.
Size Flushing flow ø [mm] Mat. No.
In a closed circuit, it ensures a minimum boost pressure level in qv [L/min] of orifice
addition to the case flushing. 45 3.5 1.2 R909651766
Hydraulic fluid is directed from the respective low pressure 107, 125 8 1.8 R909419696
side into the motor housing. This is then fed into the reservoir, 160, 180 10 2.0 R909419697
together with the case drain fluid. The hydraulic fluid, removed
250 10 2.0 R909419697
out of the closed circuit must be replaced by cooled hydraulic
fluid from the boost pump. 355, 500 16 2.5 R910803019
With port plate 027, the valve is mounted directly on the fixed With sizes 45 to 180, orifices can be supplied for flushing
motor (sizes 45 to 180, 250); with port plate 017 (sizes 355 flows from 3.5 to 10 L/min. For other flushing flows, please
and 500) on a plate. state the required flushing flow when ordering. The flushing
flow without orifice is approx. 12 to 14 L at low pressure
Cracking pressure of pressure retaining valve
ΔpND = 25 bar.
(observe when setting the primary valve)
Sizes 45 to 500, fixed setting________________________16 bar Flushing and boost pressure valve, integrated (code 9)
Switching pressure of flushing piston Dp Size Throttle ø [mm] qv [L/min]
Sizes 45 to 500_________________________________ 8±1 bar 56, 63, 1.5 6
Flushing flow qv 80, 90 1.8 7.3
Orifice (throttles with integrated valve) can be used to set the
flushing flows as required.
Following parameters are based on:
DpND = pND – pG = 25 bar and ν = 10 mm2/s
(pND = low pressure, pG = case pressure)
Schematic
T1 A (B) Flushing piston
Flushing orifice
Pressure
retaining valve
T2 B (A)
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 35/46
Flushing and boost pressure valve Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
Dimensions
Port plate 027 – SAE flange ports at side Port plate 017 – SAE flange ports at rear
View X
View Y
A1
M16x2; 21 deep1)
A
B A
A2
98
A4
Y
X
B 40
A2
A1 ø18; 40 deep
A3
Size A1 A2 Size A1 A2 A3 A4
45 223 151 355 356 120 421 198
107, 125 294 192 500 397 130 464 220
160, 180 315 201
1) DIN 13, observe the general instructions on page 46 for the
250 344 172 maximum tightening torques
Port plate 029 – SAE flange ports at side
A1 View Y
A B
A2
125
Y
Size A1 A2
56, 63 225 176
80, 90 257 186.7
36/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
The MHDB pressure-relief valves (see RE 64642) protect the Version without pressure boost facility "191"
hydraulic motor from overload. As soon as the set cracking T1 MB
pressure is reached, the hydraulic fluid flows from the high-
pressure side to the low-pressure side. B
The pressure-relief valves are only available in combination with
port plates 181, 191 or 192 (counterbalance valve for mounting
to port plate 181: see next page).
S1
Cracking pressure setting range_ _____________ 50 to 420 bar
With the version "with pressure boost facility" (192), a higher
pressure setting can be realized by applying an external pilot A
pressure of 25 to 30 bar to port PSt.
When ordering, please state in plain text: T2 MA
–– Cracking pressure of pressure-relief valve Version with pressure boost facility "192"
–– Cracking pressure with pilot pressure applied to PSt T1 MB PSt
(only with version 192)
B
S1
T2 MA PSt
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 37/46
Dimensions
D1
D2
D5 View Z:
Version without pressure boost facility "191" or "181"
D8
D3
T1
D7
D6
Z
T2
MB MA
MB S1 S1
View Y Y View Z:
D10
Version with pressure boost facility "192"
D12
D8
D11
PSt
D4
Only with
B port plate
D9
"181"
A
D6
D13
MB S1 MA
Ports
Designation Port for Standard Size Maximum pressure State3)
[bar]2)
A, B Service line SAE J518 See above 450 O
S1 Supply (only with port plate 191/192) DIN 3852 See above 5 O
MA, M B Measuring operating pressure DIN 3852 See above 450 X
PSt Pilot pressure (only with port plate 192) DIN ISO 228 See above 30 O
1) Observe the general instructions on page 46 for the maximum tightening torques.
2) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and
fittings.
3) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
38/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
Counterbalance valve BVD and BVE Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
Function
Travel drive/winch counterbalance valves are designed to reduce the danger of overspeeding and cavitation of axial piston motors
in open circuits. Cavitation occurs if the motor speed is greater than it should be for the given input flow while braking, travelling
downhill, or lowering a load.
If the inlet pressure drops, the counterbalance spool throttles the return flow and brakes the motor until the inlet pressure returns
to approx. 20 bar.
Note
–– BVD available for sizes 28 to 180 and BVE available for sizes 107 to 180.
–– The counterbalance valve must be ordered additionally. We recommend ordering the counterbalance valve and the motor as a
set. Ordering example: A2FM90/61W–VAB188 + BVD20F27S/41B–V03K16D0400S12
–– The counterbalance valve does not replace the mechanical service brake and park brake.
–– Observe the detailed notes on the BVD counterbalance valve in RE 95522 and BVE counterbalance valve in RE 95525!
–– For the design of the brake release valve, we must know for the mechanical park brake:
-- the pressure at the start of opening
-- the volume of the counterbalance spool between minimum stroke (brake closed) and maximum stroke
(brake released with 21 bar)
-- the required closing time for a warm device (oil viscosity approx. 15 mm2/s)
Application option
–– Travel drive on wheeled excavators
Gext MB
L´
B B´
A A´
G´
MA T
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 39/46
Counterbalance valve BVD and BVE Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
Application options
–– Winch drive in cranes (BVD and BVE)
–– Track drive in excavator crawlers (BVD)
D D´
S
C´
C L´
D2
MA T Winch with
D1 mechanical
Mk MP1 park brake
VF VG
Counterbalance valve BVD and BVE Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
Dimensions
View Y
B1
B3
Pressure-relief valve,
see page 36, 37
T B
B5
Gext
S
B7
B2
B6
MB A
B4 A,B
Ports
Designation Port for Version Standard Size1) Maximum State4)
pressure [bar]2)
Counterbalance valve BVD and BVE Before finalizing your design, request a binding
installation drawing. Dimensions in mm.
B1
the motor port plate using the provided tacking screws. The
counterbalance valve is finally mounted to the motor by screw-
ing on the SAE flange with the following screws:
B2
6 screws (1, 2, 3, 4, 5, 8) _______________ length B1+B2+B3
2 screws (6, 7) ___________________________ length B3+B4
B4
B3
Tighten the screws in two steps in the specified sequence from Y
1 to 8 (see following scheme).
View Y
In the first step, the screws must be tightened with half the
SAE flange
tightening torque, and in the second step with the maximum
tightening torque (see following table).
Thread Strength class Tightening 2 4
torque [Nm] 6 8
M6 x 1 (tacking screw) 10.9 15.5
7 5
M10 10.9 75 Tacking screws
3 1 (M6 x 1,
M12 10.9 130
length = B1+B2,
M14 10.9 205 DIN 912)
Size 28, 32, 45 56, 63 80, 90 107, 125, 160, 180 107, 125
Port plate 18 17
B11) M10 x 1.5; 17 deep M10 x 1.5; 17 deep M12 x 1.75; 18 deep M14 x 2; 19 deep M12 x 1.75; 17 deep
B2 782) 68 68 85 68
B3 customer-specific
B4 M10 x 1.5; 15 deep M10 x 1.5; 15 deep M12 x 1.75; 16 deep M14 x 2; 19 deep M12 x 1.75; 17 deep
1) Minimum required thread reach 1 x ø-thread
2) Including sandwich plate
42/46 Bosch Rexroth AG A2FM Series 6 RE 91001/06.2012
The versions A2FM...U and A2FM...F ("prepared for speed Version "H"
sensor", i.e. without sensor) is equipped with a toothed ring on Sizes 250 to 500 with HDD sensor
the rotary group.
On deliveries "prepared for speed sensor", the port is plugged T1 X
with a pressure-resistant cover. D 30
A
With the DSA or HDD speed sensor mounted a signal propor-
tional to motor speed can be generated.
The sensors measures the speed and direction of rotation.
Ordering code, technical data, dimensions and details on the
B
C
connector, plus safety information about the sensor can be
found in the relevant data sheet.
DSA_ _______________________________________ RE 95133
HDD________________________________________ RE 35135
The sensor is mounted at the specially provided port D as fol- View X
lows:
DSA_ _____________________________with one mounting bolt
Without HDD sensor With HDD sensor
HDD_____________________________ with two mounting bolts M6x1 (DIN 13)
8 deep
We recommend ordering the A2FM fixed motor complete with
22
20 22
sensor mounted.
20
Version "V"
ø18.2
°
Sizes 23 to 200 with DSA sensor 90
D
A
C
B
Version "V"
Sizes 250 to 500 with DSA sensor
On request
RE 91001/06.2012 A2FM Series 6 Bosch Rexroth AG 43/46
Installation instructions
General Below-reservoir installation (standard)
During commissioning and operation, the axial piston unit must Below-reservoir installation means that the axial piston unit is
be filled with hydraulic fluid and air bled. This must also be installed outside of the reservoir below the minimum fluid level.
observed following a relatively long standstill as the axial piston 1 2
unit may drain back to the reservoir via the hydraulic lines.
ht min ht min
Particularly in the installation position "drive shaft upwards"
filling and air bleeding must be carried out completely as there hmin hmin
is, for example, a danger of dry running.
T1 T2
The case drain fluid in the motor housing must be directed to
the reservoir via the highest available drain port (T1, T2).
For combinations of multiple units, make sure that the respec-
tive case pressure in each unit is not exceeded. In the event of
pressure differences at the drain ports of the units, the shared
drain line must be changed so that the minimum permissible
3 4
case pressure of all connected units is not exceeded in any
situation. If this is not possible, separate drain lines must be ht min ht min
laid if necessary.
hmin hmin
To achieve favorable noise values, decouple all connecting
lines using elastic elements and avoid above-reservoir installa- R(U)
T1
tion.
In all operating conditions, the drain line must flow into the T2
reservoir below the minimum fluid level.
Installation position
See the following examples 1 to 8.
Further installation positions are possible upon request.
Above-reservoir installation
Recommended installation positions: 1 and 2.
Above-reservoir installation means that the axial piston unit is
Note installed above the minimum fluid level of the reservoir.
With sizes 10 to 200 with installation position "shaft upward",
Recommendation for installation position 8 (drive shaft
an air-bleed port R is required (state in plain text when ordering
upward): A check valve in the drain line (cracking pressure
- special version). With sizes 250 to 1000, port U is provided
0.5 bar) can prevent draining of the motor housing.
as standard in the area near the bearings for air bleeding.
Installation 5 6
Air bleed Filling
position L1 L1
1 – T1 T1 T2
2 – T2
3 – T1
4 R (U) T2
5 L1 T1 (L1)
6 L1 T2 (L1) ht min
ht min
7 L1 T1 (L1) hmin
hmin
8 R (U) T2 (L1)
7 8
L1 Filling / air bleed
L1
R Air bleed port (special version) R(U)
T1
U Bearing flushing / air bleed port L1
T1, T2 Drain port T2
0.5 bar
1-Headline
General instructions
–– _The motor A2FM is designed to be used in open and closed –– The data and notes contained herein must be adhered to.
circuits.
–– _The product is not approved as a component for the safety
–– The project planning, installation and commissioning of the concept of a general machine according to ISO 13849.
axial piston unit requires the involvement of qualified person-
–– The following tightening torques apply:
nel.
-- Fittings:
–– Before using the axial piston unit, please read the corre-
Observe the manufacturer's instructions regarding tighten-
sponding instruction manual completely and thoroughly. If
ing torques of the fittings used.
necessary, these can be requested from Bosch Rexroth.
-- Mounting bolts:
–– During and shortly after operation, there is a risk of burns
For mounting bolts with metric ISO thread according to
on the axial piston unit. Take appropriate safety measures
DIN 13 or with thread according to ASME B1.1, we recom-
(e. g. by wearing protective clothing).
mend checking the tightening torque in individual cases in
–– Depending on the operating conditions of the axial piston accordance with VDI 2230.
unit (operating pressure, fluid temperature), the characteris-
-- Female threads in the axial piston unit:
tic may shift.
The maximum permissible tightening torques MG max are
–– Service line ports: maximum values for the female threads and must not be
exceeded. For values, see the following table.
-- The ports and fastening threads are designed for the
specified maximum pressure. The machine or system -- Threaded plugs:
manufacturer must ensure that the connecting elements For the metallic threaded plugs supplied with the axial pis-
and lines correspond to the specified application condi- ton unit, the required tightening torques of threaded plugs
tions (pressure, flow, hydraulic fluid, temperature) with the MV apply. For values, see the following table.
necessary safety factors.
-- The service line ports and function ports can only be used
to accommodate hydraulic lines.
Bosch Rexroth AG © This document, as well as the data, specifications and other information set
Mobile Applications forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
Glockeraustrasse 4 An den Kelterwiesen 14 duced or given to third parties without its consent.
89275 Elchingen, Germany 72160 Horb, Germany The data specified above only serve to describe the product. No statements
Tel.: +49-7308-82-0 Tel.: +49-7451-92-0 concerning a certain condition or suitability for a certain application can be de-
Fax: +49-7308-72-74 Fax: +49-7451-82-21 rived from our information. The information given does not release the user from
the obligation of own judgment and verification. It must be remembered that our
info.brm@boschrexroth.de
products are subject to a natural process of wear and aging.
www.boschrexroth.com/axial-piston-motors
Subject to change.