Professional Documents
Culture Documents
TECHNICAL SPECIFICATIONS
This set of Specifications shall govern the methods of construction and the kinds of
materials to be used for the CONTINUATION OF ROOFING SYSTEM FOR ONE (1) BASKETBALL
COURT, TWO (2) VOLLEYBALL COURTS AND ONE (1) LAWN TENNIS shown in the plans and
detail drawings.
GENERAL CONDITIONS
All parts of the construction shall be finished with first class workmanship, to the fullest
talent and meaning of the plans and these Specifications, and the entire satisfaction of the
Architect/Engineer.
The construction shall conform to all the requirements of the National Building Code,
as well as the local rules and regulations of the Office of the Building Official of Naval, Biliran,
Philippines.
The Contractor shall be responsible for safety of all workmen and other persons
entering the Works and shall at his own expense; where not stated otherwise take all
measures, subject to the Engineer's approval, necessary to ensure their safety.
Such measures shall include but not be limited to:
• Provision of safety and emergency regulations for fire, gas, and electric shock
prevention, together with rescue operation plan
• Safe control of flowing water
• Provision and maintenance of suitable lighting to provide adequate illumination
at place of work with appropriate spares and standby unit
• Provision and maintenance of safe, sound slings, pulleys, ropes, net and other
lifting device
• Provision of safe access to any part of the works.
• Provision of notices in local dialect temporarily or permanently during
construction at locations likely to be used by the public. Placement of such
notices shall depend on the existence of the nature of work in the vicinity.
These notices shall be in addition to any other statutory requirements demanded
of the Contractor
- The Contractor shall ensure that all his Employees are fully conversant with
the regulations, emergency and rescue procedures etc. and shall enforce a
rule that will instantly dismiss any employee committing a serious breach of such
regulations.
- The Contractor shall provide one (1) First Aider and (1) one Part-time Safety
Practitioner
• The scope of work shall include service of at least one part-time experienced
health worker/health assistant with a minimum of once a week full time site visit
CONTINUATION OF ROOFING SYSTEM FOR ONE (1) BASKETBALL COURT, TWO (2) VOLLEYBALL COURTS AND ONE (1) LAWN TENNIS Page 3
as work assignment. The Contractor shall also supply and provide adequate
medicines and facilities required for standard first aid.
• The Contractor shall inform the Engineer regarding the medical facility within
a week after its establishment and operation.
Safety Equipment:
Safety Helmets
Safety Shoes
Safety Gloves
Safety Vest
Rubber Boots
All excavations shall be made to grade indicated in the drawings. Where the
construction site is covered with any kind of fill, the excavation for footings should be made
deeper until the stratum for safe bearing capacity of the soil is reached.
Equipment:
- Excavator w/ breaker (Cap. 0.28 cu.m.) - Dump Truck (12yd³)
- Diesel Powered Water Pump - Minor Tools
Equipment:
- Excavator with breaker (Cap. 0.28 cu.m.)
- Dump Truck (5 cu.m capacity)
- Plate Compactor
- Minor Tools
Materials:
Crushed Gravel ¾”
All concrete shall be mixed thoroughly until there is uniform distribution of the cement
and aggregates, and should be deposited as nearly as practicable in its final position, care
being taken to avoid segregation of the aggregates.
Water to be used for mixing concrete shall be clean and free from injurious amount
of oil, acids, alkalis, salt and other organic materials.
PROPORTIONING OF CONCRETE
All concrete work shall be done in accordance with the standard specifications for
plain and reinforced concrete as adopted by the Government. Cement to be used shall be
Portland Cement.
The following proportion of concrete mixture shall be used for the various parts of the
building:
Columns, footings, Wall Footing &
Footing tie beam - Class A (1 : 2 : 4)
Concrete Hollow Blocks - Class B (1 : 3)
Reinforced Concrete Beams and Slabs - Class A (1 : 2 : 4)
Concrete slab floor (suspended) - Class A (1 : 2 : 4)
The fine aggregate for concrete shall consist of natural sand, or of inert materials with
similar characteristics, having clean, hard and durable grains, free from organic matter or
loam.
The coarse aggregate for concrete shall consist of crushed rock or durable or strong
qualities or clean and hard gravel. Size of the coarse aggregate to be used shall vary from
20mm to 40mm (3/4” to 1-1/2”)
Materials: Equipment:
- Portland Cement, Type I, 40Kg Concrete Mixer, 1-2.0 bagger
- Washed Fine Sand Concrete Vibrator
- Crushed Gravel ¾”
CONTINUATION OF ROOFING SYSTEM FOR ONE (1) BASKETBALL COURT, TWO (2) VOLLEYBALL COURTS AND ONE (1) LAWN TENNIS Page 5
Description of Works: Columns, Footings, Footing Tie Beams, Beams, Suspended Slabs
(Concrete Bleacher Top), Slab on fill (Elevated floor) & Canal Flooring.
Concrete slab on fill shall be poured on a gravel bed of not less than 50mm thick.
Each concrete slab course to be poured shall not be more than one meter wide, and each
course shall be poured alternately to the indicated floor finish.
Stainless Floor Drains size 4” in diameter shall be provided on the floor at every 5-
meter span of perimeter wall which will be attached to 4” in diameter pvc Elbow with 4’’ to
2’’ Reducing bush and 2” diameter pvc pipe going to the drainage canal outside the
building. Please refer to the Structural Design as indicated in the plans.
Materials:
4” Stainless Floor drain Bee hive type
4’’ pvc elbow, sch.40
4” to 2” Reducing bush, sch.40
2” diam. pvc pipe, sch.40
Materials: Equipment:
- 4” Concrete Hollow Block (Interior Walls) Concrete Mixer, 1.5-2.0 bagger
All steel reinforcing bars to be used in this construction shall consist of round
deformed bars with lugs or projections on their sides to provide greater bond between the
concrete and steel. All steel reinforcing bars to be used shall be:
Materials: Equipment:
12 mm ø x 6 m Deformed RSB
16 mm ø x 6 m Deformed RSB Rebar Cutter
10 mm Ø x 6m Deformed RSB Hacksaw Blade
G.I Tie Wire Ga.#16
Heavy Duty Hacksaw Blade
All steel reinforcing bars shall be accurately placed and secured against
displacement by tying them together at each bars intersection with Gauge # 16 galvanize
iron wire.
The steel reinforcing bars indicated for footings, columns, slabs, beams girders and
other concrete members shall all conform to the number, size and spacing as indicated in
the drawings or schedule of steel reinforcements.
No metal reinforcement shall be installed in place unless it is free from rust, scale or
other coatings, which will destroy or reduced the bond with concrete. Use Rust converter in
removing the presence of rust prior to fabrication of Steel Reinforcement.
For Safety Hand Railings at the Reinforced Concrete Ramp, use 2” diameter Stainless
Steel Pipe Welded in accordance to satisfactory quality using stainless welding rod with
distances indicated on the drawing.
Description of Works: Columns, Column Footings, Wall & Wall footing, Footing Tie Beams,
Beams, Suspended Slabs (Bleacher Top), Slab on fill, Canal Wall &
Canal flooring, Bleachers Support, Sag Rod & Turn buckle
All work shall comply with all applicable codes including National Mechanical
Code as adopted by the local government.
Provide all materials, tools and labor required to perform the work shown on
the drawing and described in these specifications. If any material, devices, equipment or
related accessories not included on the plans but are required to complete the system and
installation shall be included of the contractor. Mechanical contractor shall not proceed to
any installation due to changes without proper submittal and approval. All materials to be
used shall be new and shall conform to the Reference Code and Standards Layout
dimension shown in drawing are approximate only and intended to serve as an installation
guide. Dimension may be adjusted as required to meet field condition.
Work shall include fabrication and installation of steel trusses, Louver Windows & Door, Safety
Harness, Entrance Door Roof Purlins and Support
Materials Equipment
2" x 3" x 1.2 mm thick Rectangular Tube Portable Welding Machine
2" x 4" x 1.2 mm thick Rectangular Tube Generator Set 1 KVA
2" x 4" x 1.5 mm thick Rectangular Tube Oxyacetylene Cutting outfit
CONTINUATION OF ROOFING SYSTEM FOR ONE (1) BASKETBALL COURT, TWO (2) VOLLEYBALL COURTS AND ONE (1) LAWN TENNIS Page 7
2" x 3" x 1.5 mm thick Rectangular Tube Electrical Saw 12” diam.
Steel Plate 12 mm Thick x 4' x 8’ Crawler Crane 46-50T
Expansion Bolt 4''
1/4" thick x 4" x 4" Angle Bar
1/4" thick x 2'' x 2'' Angle Bar
1/4" thick x 1/2" x 1-1/2" Angle Bar
1/4” thick x 0.15 m x 0.20 Gusset Plate
Heavy Duty Welding Rod
Stainless Welding Rod
12 mm ø x 6 m Stainless Round bar
12 mm ø x 6 m Deformed RSB
16mm∅ Stainless Steel Safety Harness anchor ring w/ 1/2" thick. Base Plate
Turn Buckle
12 mm thick Steel Buckle Plate
16mm ∅ x 6 m Steel Round Bar, Grade 40
All forms for concrete works shall be properly braced or connected together so as to
maintain the correct position and shapes of the concrete members. Forms shall be
constructed sufficiently tight to prevent bulging and seepage of water.
Forms shall not be removed until the concrete has attained sufficient strength to
support its own weight and any loads that may be placed on it. Side forms of beams and
girders maybe removed earlier than the bottom forms but additional post or shoring must be
placed under the beams or girders until they have attained the strength.
Materials:
1/4'' thck x 4' x 8' US Marine Plywood
2" x 2" x 12' Coco Lumber
2" x 2" x 10' Coco Lumber
2" x 6" x 12' Coco Lumber
2" x 3" x 12' Coco Lumber
# 4 CWN
# 2 CWN
# 1 1/2 CWN
G.I Tie Wire Ga.# 16
Metal Scaffolding
6 mm. THK. Pre-Painted Dura Curved Rib Type Roofing Long Span (22.94 m x 1.2 m)
Stainless J Bolt 1/4 x 2-1/2 with bonded washer and hex nut
CONTINUATION OF ROOFING SYSTEM FOR ONE (1) BASKETBALL COURT, TWO (2) VOLLEYBALL COURTS AND ONE (1) LAWN TENNIS Page 8
Paint works shall conform to proper painting procedure where surface area to be
painted must be free from dust, water and rust for steel surfaces. For presence of rust, rust
converter must be applied prior to painting. Fresh or new concrete or masonry shall be
treated with neutralizer and sealant prior to primer (2 coats) and top coat finish (2 coats).
Rectangular tubes shall be painted with Red Oxide Primer (2 coats) and Metallic Gray
Acrylic Paint Finish (2 coats). (Refer to plans)
Materials:
For Steel Trusses
Metal Primer Red Oxide
Quick dry Enamel Red
Paint Thinner
Roller Brush 2 inches
Paint Brush 2-1/2 inches
Paint Tray 7 inches
For Walls
Flat Wall latex
Semi-Gloss Flat Latex
Concrete Neutralizer
Concrete Sealer (Acrytex Primer)
Roller Brush 7 inches
Paint Tray 7 inches
Acrytex Cast
For Columns
Flat Wall latex
Semi-Gloss Flat Latex
Concrete Neutralizer
Concrete Sealer (Acrytex Primer)
Roller Brush 7 inches
Paint Brush 2-1/2 inches
Paint Tray 7 inches
Acrytex Cast
CRB Reducer
Roller Brush 7 inches
Paint Tray 7 inches
Paint Brush 2-1/2 inches
Rubber floor CRB Marking Yellow
Rubber floor CRB White
For Rectangular Tube Louver door, Roof purlins & frame support
Metal Primer Red Oxide
Quick dry Enamel Red
Paint Thinner