Professional Documents
Culture Documents
REMOVAL
PROCEDURE
S E R V I C E M A N U A L
2.0/2.5/3.5 kW Class
9000/13000 Btu/h Class
Indoor Unit
Inverter / Non-Inverter
Wall Mounted Type
Table of Contents
1. Air Filters .................................................................................................2
2. Front Panel..............................................................................................3
3. Front Grille ..............................................................................................4
4. Horizontal Blades / Vertical Blade ASSYs ..............................................5
5. Electrical Box ..........................................................................................7
6. PCBs .......................................................................................................9
7. Drain Pan Unit / Swing Motor................................................................13
8. Fan Motor..............................................................................................15
9. Indoor Heat Exchanger .........................................................................17
10.Fan Rotor ..............................................................................................20
Note: The illustrations may be slightly different depending on the model.
Removal Procedure 1
Downloaded from www.Manualslib.com manuals search engine
Air Filters Si041251EC
1. Air Filters
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1. Remove the air filters. The air filter is not marked
1 Open the front panel. for difference between the
Front panel
right and left sides.
2 Pull out the air filter
downward and remove Insert the air filter with the
it. “FRONT” mark faced up.
Titanium apatite
photocatalytic air-
purifying filter ASSY (R17198)
(R13174)
2 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Front Panel
2. Front Panel
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1 Open the front panel Front panel
over the position where
it stops.
(R4312)
(R4313)
Removal Procedure 3
Downloaded from www.Manualslib.com manuals search engine
Front Grille Si041251EC
3. Front Grille
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1 Remove the screw Horizontal blade Open the horizontal blades
covers and screws. before removing the screw
(right and left) covers and screws.
(R17199)
(R12715)
(R16030)
(R4327)
Spacer
Section View
(R4590)
(R4565)
4 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Horizontal Blades / Vertical Blade ASSYs
(R4329)
(R4330)
(R4331)
Removal Procedure 5
Downloaded from www.Manualslib.com manuals search engine
Horizontal Blades / Vertical Blade ASSYs Si041251EC
Hook
(R17200)
(R4336)
Hook
6 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Electrical Box
5. Electrical Box
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1 Remove the screw of
the wire fixture. Electrical box
Wire fixture
(R17926)
(R17202)
(R4343)
Removal Procedure 7
Downloaded from www.Manualslib.com manuals search engine
Electrical Box Si041251EC
Clip
(R21411)
(R11234)
(R4346)
(R17204)
[S1]
(R4349)
8 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC PCBs
6. PCBs
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1. Remove the shield plate.
1 The figure shows the
appearance of the
electrical box.
(R4350)
Shield plate
Hook
Hook
(R4352)
(R19206)
Removal Procedure 9
Downloaded from www.Manualslib.com manuals search engine
PCBs Si041251EC
Terminal board
(R4354)
(R19301)
Hook
(R12725)
Hook
(R16033)
10 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC PCBs
(R20213)
(R4363)
3 Disconnect the
connector [S36] from
the INTELLIGENT EYE INTELLIGENT
sensor PCB. EYE sensor PCB
(R17206)
Removal Procedure 11
Downloaded from www.Manualslib.com manuals search engine
PCBs Si041251EC
Display PCB
(R4366)
Hook
(R4367)
3 Disconnect the
connector [S27] from [S27]
the display PCB.
(R20214)
12 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Drain Pan Unit / Swing Motor
Hook
Twist here.
(R4376)
Swing motor
(R17208)
Removal Procedure 13
Downloaded from www.Manualslib.com manuals search engine
Drain Pan Unit / Swing Motor Si041251EC
(R4382)
Hook
Hook
(R4383)
(R4384)
14 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Fan Motor
8. Fan Motor
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1 Release the fan motor
lead wires from the
hooks.
(R4389)
(R4390)
Hook (a)
(R20215)
Removal Procedure 15
Downloaded from www.Manualslib.com manuals search engine
Fan Motor Si041251EC
(R20216)
Fan motor
(R4394)
16 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Indoor Heat Exchanger
Caution Be sure to conduct pump down operation before disassembling the refrigerant pipe.
If the refrigerant leaks, repair the spot of leaking, then collect all refrigerant from the
unit. After conducting vacuum drying, recharge proper amount of refrigerant.
From the viewpoint of global environmental protection, make sure to use a vacuum
pump for air purging.
Step Procedure Points
1 Remove the 2 screws
which fix the indoor
heat exchanger to the
installation plate.
(R4396)
Drain hose
Carry out the removal work
(R17210)
with 2 wrenches.
(R4400)
Removal Procedure 17
Downloaded from www.Manualslib.com manuals search engine
Indoor Heat Exchanger Si041251EC
(R4401)
(R17211)
Upper
hook (left) (R17927)
Lower hook
(left)
(R17928)
18 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Indoor Heat Exchanger
(R4405)
Removal Procedure 19
Downloaded from www.Manualslib.com manuals search engine
Fan Rotor Si041251EC
10.Fan Rotor
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1 Remove the 2 screws When reassembling the fan
Fan motor lead wire
of the right side plate. motor and the fan rotor,
provide as much as 5 mm
2 Release the fan motor (0.2 inch) of play between
lead wire from the the side face of the rotor and
hooks and remove the the bottom frame.
right side plate. Hook
remove the fan motor (1) Insert the fan motor with
and the fan rotor. Screw approx. 5 mm (0.2 inch) left.
(2) Tighten the screw until it
stops. Then give the screw
one more turn.
(3) Rotate the fan rotor and
confirm the fan motor and
the fan rotor are installed
appropriately.
Fan rotor Fan motor (4) Tighten the screw
(R19302)
completely if appropriate.
(5) If not appropriate, go back to
(1).
20 Removal Procedure
Downloaded from www.Manualslib.com manuals search engine
Si041251EC Fan Rotor
Left side
plate
(R4414)
Hook
Hook
(R4415)
(R4416)
Removal Procedure 21
Downloaded from www.Manualslib.com manuals search engine
Revision History
Month / Year Version Revised contents
Dealer
Head Office:
Umeda Center Bldg., 2-4-12, Nakazaki-Nishi,
Kita-ku, Osaka, 530-8323 Japan
Tokyo Office:
JR Shinagawa East Bldg., 2-18-1, Konan,
Minato-ku, Tokyo, 108-0075 Japan
http://www.daikin.com/products/ac/
c All rights reserved
zSpecifications, designs and other content appearing in this brochure are current as of February 2015 but subject to change without notice.
Si041251EC
02/2015 AK.B