Professional Documents
Culture Documents
Home Measurements
Prize fund
for January 2020
Description and circuit diagram of the
1. 1000 rub
multimeter M890G Soldering Iron Site
2.200 rub.
From users
join
Similar articles:
Description: The
M890G multimeter is a compact, wear-resistant, pocket-sized multimeter for monitoring constant and
alternating voltage, direct current, resistance, capacitance, frequency, temperature, checking diodes and
transistors, and a continuity.
Dual Integration CMOS ADC with automatic zero correction, automatic polarity detection and overload
indexing. Overload protection is provided up to the specified limits.
Ideal for use in the field, laboratory, workshop and household.
Display - 3 1/2 - digit, 7-segment liquid crystal display.
Power supply: one 9-volt battery type 6F22. Dimensions: 88x170x38mm. Weight 340g.
Accuracy is guaranteed for 1 year, at 23 ± 5 ° C and relative humidity less than 75%.
Features:
Power switch - ON-OFF key.
One 30-position switch for choosing the type of work and / or limit.
High sensitivity - 100 μV.
Automatic overload indication - "1" in the high order.
Automatic polarity detection of direct voltage or current.
All limits are protected against overload.
Testing resistances from 0.1 ohms to 200 megohms.
Check capacitance from 1pF to 20uF.
Testing diodes with a fixed forward current of 1mA.
Checking transistors at I = 100 μA.
Temperature measurement
Specifications
Constant pressure
AC voltage
Limit Resolution Accuracy
2B 1 mB ± 0.8% ± 3 units
20 B 10 mB ± 0.8% ± 3 units
200 B 100 mB ± 0.8% ± 3 units
700 B 1 B ± 1.2% ± 5 units;
D.C
Alternating current
Resistance
Overload
15s maximum 200V eff. on all limits.
Protection:
At the limit of 200 megohms, when the probes are closed, the display will read 10 units,
Note:
which should be subtracted from the reading.
Capacity
Temperature
Frequency
Model Constant AC D.C Alternating Resistance Diode Sound Transistor Auto Frequency Temperature
pressure voltage current test probe test off
890B + (+ + (+ 2mA,
+ + + + + + - - -
+ 200mV) 20mA)
890C + + + + + + + + - - +
+ (+
890D + + + + + + + - - -
20mA)
890F + + + + + + + + + + -
890G + + + + + + + + + + +
Reward I collected 0 0
Reply
Reply
Reply
Reply
Reply
Reply
Reply
Reply
Reply
Vladimir 07/13/2013 10:50 # 0
The device turns on for a second and then goes out. If you press the power button many times, the
multimeter turns on. The battery is new. The switch replaced.
Reply
Reply
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Ответить
Прибор - откровенный шлак без защиты. Если в режиме омметра нарваться на фазу или
постоянное напряжение Вольт так 90, то прибор просто сгорает. Те же UNI-T гораздо
живучее.
Ответить
Ответить
Ответить
Прибор Mastech M890G+. Не точные показания при измерении 12В, в пределе измерений
20В. На пределе измерения 200В, показания нормальные. Подскажите где искать причину?
Ответить
Ребята, прошу помочь с ремонтом M890F: сразу после включения показывает значок питания
и через 1 сек гаснет индикатор. Может быть - из-за схемы атоотключения; как она работает.
Работал в позиции переключателя "KHz"; видимо - не совсем корректно (измерял
незнакомую цепь).
В качестве питания использую трансформат. блок пит. (транс+мост+электролит) без стаба, с
выходом порядка (10-12) вольт. Может ЭТО быть причиной.
Ответить
Добавить комментарий
Ваш комментарий
Текст:
Оставить комментарий