Professional Documents
Culture Documents
Tda2003 PDF
Tda2003 PDF
DESCRIPTION
The Contek TDA2003 is a monolithic audio power amplifier
integrated circuit.
FEATURES 1
*Very low external component required.
*High current output ( up to 3 A).
*Low harmonic and crossover distortion.
*Built-in Over temperature protection.
*Short circuit protection between all pins.
TO-220B
PIN CONFIGURATIONS
1 Non inverting input
2 Inverting input
3 Ground
4 Output
5 Supply Voltage
BLOCK DIAGRAM
3
Contek
1 2
TEST CIRCUIT
+Vs
100 mF
C3
100nF
Vi
1
5 C4
C1 1000 m F
Contek 4
1 mF
TDA2003
2 3 R1
220 W R3
1W RL
Rx C2
39 W 470 m F R2 100nF
2.2 W
Cx
39nF
C3
mA 100nF
Vi Vi
1 1
5 5 C4
1000 mF
C1 1000mF
Contek 4 Contek 4
1 mF
TDA2003 TDA2003
2 3 R1 2 3
220W R1
220W R3
RL 1W RL
R2 Rx C2
470 mF
V 2.2W 39W 470 mF R2
100nF
2.2W
Cx
39nF
Rx=20*R2 Cx=1/(2pB*R1)
8 80 20 Gv=40dB
f=1kHz
d=10% R=1.6W
6 60 15
R=2W
4 40 10 R=3.2W
R=4W
2 20 5
0 0 0
8 10 12 14 16 Vs(V) 8 10 12 14 16 Vs(V) 0 5 10 15 20 Vs(V)
Fig.4outputpowervs.load
Fig.5Gainvs.Inputsensitivity Fig.6Gainvs.Inputsensitivity
resistance
58 58
Po
(W) 54 54
Gv=40dB
Gv=40dB f=1kHz
16 Gv=40dB 52 52
Vs=16V f=1kHz RL=2W
f=1kHz
RL=4W
d=10% 48 48
Vs=14.4V
12 44 44
40 40
Vs=12V
8 36 36
32 32
Vs=8V
4 28 28
24 24
0 20 20
0 2 4 6 8 10 100 Vi(rms) 1000 10 100 Vi(rms) 1000
RL(W)
1
Po=2.5W
0.4 -30
0.1
0.2 -40
Po=50mW
0.01 0 -50
0.1 1 10 100 1 2 3 4 30 35 40 45 50 55
Po(W) 10 10 10 10
Frequency (Hz) Gv(dB)
Ptot
-60 R2=1W
2 20 2 20
-80 0 0 0 0
2 3 4 5 0 2 4 6 8 0 2 4 6 8
10 10 10 10 10
frequency(Hz) Po(W) Po(W)
B=15kHz
15 15
10
RL=1.6W B=20kHz
10 10
RL=2W
10 X C/W
RL=3.2W R2=2.2W
5 5
RL=4W
30 X C/W
0 0 1
0 5 10 15 20 Vs(V) 0 50 100 150 200 36 40 44 48 Gv(dB)
Tamb( X C)
APPLICATION CIRCUIT
+Vs
100 mF
C3
100nF
Vi
1
5 C4
C1 1000 m F
Contek 4
1 mF
TDA2003
2 3 R1
220 W R3
1W RL
Rx C2
39 W 470 m F R2
100nF
2.2 W
Cx
39nF
1W 0.1mF
2.2 mF 2.2 mF
1 5 5 1
Contek 4 4 Contek
TDA2003 TDA2003
2 RL=4W 2
3 3
0.1 mF
200W 430W
C3 C4
15 mF 16W 10 mF
16W
The Values of the capacitors C3 and C4 are different to optimize the SVR(Typ. 40dB)
Vs=14.4V
0.1 mF
0.1 mF 0.1 mF
1 5 RL=4W 5 1
Contek 4 4 Contek
TDA2003 TDA2003
2 2
0.1 mF
0.1 mF
3 3
C3
15 mF 620W
1nF
t1=50ms
Vs
(V)
40
A B
2mH
From
To
Supply 3000 mF Pin 5
Voltage 16V
14.4
t
t2=1000ms
POLARITY INVERSION
High current(up to 5A) can be handled by the device with no damage for a longer period than the blow-out time of a
quick 1A fuse(normally connected in series with the supply).
The feature is added to avoid destruction if, during fitting to the car, a mistake on connection of the supply is made.
OPEN GROUND
When the radio is in the ON condition and the ground is accidentally opened, a standard audio amplifier will be
damaged. On the Contek TDA2003 protection diodes are included to avoid any damage.
INDUCTIVE LOAD
A protection diode is provide between pin 4 and pin 5(see the internal schematic diagram) to allow use of the Contek
TDA2003 with inductive loads. In particular, the Contek TDA2003 can drive a coupling transformer for audio modulation.
DC VOLTAGE
The maximum operating DC voltage on the Contek TDA2003 is 18V.
However the device can withstand a DC voltage up to 28V with no damage. This could occur during winter if two
batteries were series connected to crank the engine.
APPLICATION SUGGESTION
The recommended values of the components are those shown on application circuit of Fig.16. Different values can be
used. The following table can help the designer.
www.DatasheetCatalog.com