‘3000 | 2000 | 1600 | 1280
‘3000 | 3000 | 1600 | 1250
‘3000 | 2000 | 1600 [ 1250 | 1000 | #00
1600 | 1250 | 800
‘3000 | 3000 | 1280 | @2s
‘3000 | 2000 | 1600 | 1250 | 62s
3000) os
‘3000 | 2000 | 1600 | 1250 | 1000 | 800
‘3000 | 3000 | 2000” | 1600 | ¥2s0_| 800
3000 | 2000 | 1600 | 1250 | 1000 | soo | #00
‘3000 | 3000 | 2000 | 1600 | 1250 | 1000 | 800
‘3000 | 2000 | 1600 | 1350) 1000 | 800 | 800 | 800 | as
‘3000 | 3000” | 2000 | 1600 | 1260 | 1000 | 800 | soo | #00
‘3000 | 2000 | 160 | 1250 | 1000 | 800 | 800 | soo | #00
3000 | se | 2000 | 1600 | 1250 | vo00 | 00 | 00 | 800
Notes (epplicable 10 Tables 2 co 4)
(1) The joints and stiffeners have been rated in terms of duct longer side and maximum spacing — see 104
fe joins and 10 for stiffeners,
@ In
(@) Stiffened panels may limit the choice of insulation materials.
(4) For ductwork galvanized after manufacture, see 10.6 and Appendix E.
(5) For aluminium ductwork, see Appendix H.
(6) For constructional constraints of stainless steel ductwork see Appendix F.
(3) Although not covered in this speciation, due to their relatively infequect use, cleted cross joints ae
fn accepted constructional practice and the HVCA Ductwork Group should be contacted if detils of
18|__ ae [| a |
Fig. 10 | Duct ends sumed up 8 mm
ae
oe) (Gee aay
+ ed Fixing Bolts Angle flanged joint does NOT
| require DW/TMI cetificstion
25x3 | 6mm |
Ne 30x4 | & mm
| oxd | sam ‘A turn up as ilusiated i¢ NOT
ending reser | 505 | 10 mm mandatory. Tf not uted, the toe
| of the angle is 10 be sealed.
Fins cannes Goal ALES tae el rome
2K —f.
ane epee ese
Fig. 12 Examples of typical cross joint flanges formed from the duct wall
a gai eS
al
NOTE: The above illastatons are typical examples sf cross joint profiles that are in common use for counting
rectangular atest meal dts,
Thace te no set dimensions for these profiles shows ia Figs. 11 and 12 provided they are certified under the HVCA.
testing scheme DW/TMI “Acceptance Scheme for new products ~ Rectungular cross Joint clesifienion” and ate
Appropriate to the duct aplication. The manufactrer's technica deta should be fllowed wih respect to
CConmestions to aut wall
(Comer teatmest
Aaihion of cle
‘Applieton of sealants
we Stennis
Applction of te ban,
4 ist oF manufacturers and profiles that ae covered by cumeht DW/TMI certificate jx available from the Ductwork
Group Secretary st HVCA,
aT
Section u Thickness Rating
(Fig. a8 35 3
. 0 4
ee +
Pa 5
6a 5 |
Fig. 18 |
i 2s 16 |
30 16 3
0 16 83
50 20 st
pees 20 16 si
25 16 sz
3 16 3
“ 20 pe
Fig. 3 —z oF
20 2 2
2s 16 83
0 16 st
aa 20 os
Fig. 22
20 os st
30 10 8
| s 40 res 3
(Fig. | |
33 os si
Note — Other profiles may be used providing the duct deflecion is limited to « macimum of Taw of the dust
side under operating. pressu
useing show rolled steel engle
silffeces. Sufenes shown in Fisk 19 10
23 are permitod. If used ae fall inh
stiffeners rigid comers are requied.
Back to back stiffener with
: “bolted corners
Longest side stitfener
with short side 400 mm and less
Ductwork
eae ae A eS
a