Professional Documents
Culture Documents
Sharp LC-32M44L LC-37M44L PDF
Sharp LC-32M44L LC-37M44L PDF
LC-32/37M44L
SERVICE MANUAL
No. S48J1LC32M44L
LC-32M44L
LC-32M44L LC-37M44L
MODELS LC-37M44L
In the interests of user-safety (Required by safety regulations in some countries) the set should
be restored to its original condition and only parts identical to those specified should be used.
OUTLINE
This model is based on the LC-32/37D44U and is changed some parts. This Service Manual covers the modifications
alone. For the other points, refer to the LC-32D44U (No. SY7C1LC32D44U) and LC-37D44U (No. S18D7LC37D44U)
Service Manual.
CONTENTS
OUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINE.................................................................... i
LIST OF CHANGED PARTS (LC-32M44L)................ i
LIST OF CHANGED PARTS (LC-37M44L)............... ii
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY
PRECAUTION...........................................................iii
PRECAUTIONS A PRENDRE LORS DE LA
REPARATION .......................................................... iv
PRECAUTIONS FOR USING LEAD-FREE
SOLDER ................................................................... v
PRECAUTIONS IN SERVICING THE HDCP-
KEY ROM................................................................. vi
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS .................................................1-1
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS ........................................................3-1
Parts Guide
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
OUTLINE
This model is based on the LC-32/37D44U and is changed some parts. This Service Manual covers the modifications alone. For the other points,
refer to the LC-32D44U (No. SY7C1LC32D44U) and LC-37D44U (No. S18D7LC37D44U) Service Manual.
LC-32D44U LC-32M44L
Ref. No. Description Note
(No. SY7C1LC32D44U) (No. S48J1LC32M44L)
PRINTED WIRING BOARD ASSEMBLIES
R/C, LED Unit DUNTKE264FM02 ← Some parts changed
KEY Unit DUNTKE266FM02 ← —
MAIN Unit DUNTKE450FM01 DUNTKE450FM03 Some parts changed
POWER/INVERTER Unit RUNTKA397WJQZ RUNTKA419WJQZ —
LCD PANEL
LCD Panel Module Unit R1LK315T3GW20Z R1LK315T3GW30Z —
MAIN Unit
D1306 Photo Diode VHPGPFSV51T-1 VHPGPFSV51V-1 Change
D9003 Zener Diode RH-EX1234CEZZY — Delete
IC1604 IC VHiSii9185+-1Q VHiSii9185A-1Q Change
P2001 Plug QPLGN0060CEZZY — Delete
P9202 Plug QPLGNA144WJZZY — Delete
P9301 Plug QCNCWA562WJQZY — Delete
Q509 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q510 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
Q515 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q516 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q517 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q518 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q519 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q520 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q521 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q522 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q523 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q524 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q1101 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
Q1102 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
Q1307 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q2001 Transistor VSKRC404E++-1Y — Delete
Q5414 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q9301 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
R9209 Resistor VRS-CZ1JF470JY — Delete
i
LC-32/37M44L
LIST OF CHANGED PARTS (LC-37M44L)
LC-37D44U LC-37M44L
Ref. No. Description Note
(No. S18D7LC37D44U) (No. S48J1LC32M44L)
PRINTED WIRING BOARD ASSEMBLIES
R/C, LED Unit DUNTKE264FM02 ← Some parts changed
KEY Unit DUNTKE266FM02 ← —
MAIN Unit DUNTKE450FM01 DUNTKE450FM03 Some parts changed
POWER Unit RDENCA272WJQZ RDENCA270WJQZ —
INVERTER Unit RUNTKA418WJQZ ← —
LCD PANEL
LCD Panel Module Unit R1LK370T3GW20Z ← —
MAIN Unit
D1306 Photo Diode VHPGPFSV51T-1 VHPGPFSV51V-1 Change
D9003 Zener Diode RH-EX1234CEZZY — Delete
IC1604 IC VHiSii9185+-1Q VHiSii9185A-1Q Change
P2001 Plug QPLGN0060CEZZY — Delete
P9202 Plug QPLGNA144WJZZY — Delete
P9301 Plug QCNCWA562WJQZY — Delete
Q509 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q510 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
Q515 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q516 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q517 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q518 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q519 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q520 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q521 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q522 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q523 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q524 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q1101 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
Q1102 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
Q1307 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q2001 Transistor VSKRC404E++-1Y — Delete
Q5414 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
Q9301 Transistor VS2SA1530AR-1Y VSKTA1504SG-1Y Change
R9209 Resistor VRS-CZ1JF470JY — Delete
ii
LC-32/37M44L
LC-32/37M44L
SAFETY PRECAUTION Service Manual
WARNING • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted. • Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
2. Disconnect AC power before servicing. and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
C A U T I O N : F O R C O N T I N U E D PROTECTION
reversed. (If necessary, a nonpolarized adaptor plug must be used
AGAINST A RISK OF FIRE REPLACE ONLY WITH only for the purpose of completing these checks.)
SAME TYPE FUSE.
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
F7101 (250V 6.3A) must be corrected before returning the monitor to the owner.
F7102 (250V 1A)
F7103 (250V 6.3A)
DVM
AC SCALE
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard) 1.5k ohm
Before returning the receiver to the user, perform the following 10W
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
0.15 µF
4. Inspect all protective devices such as non-metallic control knobs, TEST PROBE
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner. TO EXPOSED CONNECT TO
• Plug the AC cord directly into a 110-240 volt 50/60Hz AC outlet. METAL PARTS KNOWN EARTH
GROUND
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
iii
LC-32/37M44L
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les télévi- Pour assurer la protection, ces pièces doivent être identiques à celles
seur ACL présentent des caractéristiques spéciales relatives à la sé- utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec- les mêmes caractéristiques que les pièces recommandées par l'usine,
tion ne peut pas être nécessairement augmentée en utilisant des indiquées dans ce manuel, peut provoquer des électrocutions, incen-
pièces de remplacement étalonnées pour haute tension, puissance, dies, radiations X ou autres accidents.
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
iv
LC-32/37M44L
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
v
LC-32/37M44L
PRECAUTIONS IN SERVICING THE HDCP-KEY ROM
The HDCP-KEY ROM shall be protected and managed for its information inside. In servicing this ROM, therefore, take the following information pro-
tection/management measures.
1) When disposing of the component parts and PWBs, destruct the IC itself in a proper way.
(For repairing or replacing the component parts and PWBs as well as clearing those in stock)
2) In storing the component parts, protect and manage them against theft and disclosure.
(For storing the service parts, service units, etc.)
vi
LC-32/37M44L
CHAPTER 1. SPECIFICATIONS
LC-32/37M44L
Service Manual
[1] SPECIFICATIONS
1–1
LC-32/37M44L
CHAPTER 2. OPERATION MANUAL
LC-32/37M44L
Service Manual
Part Names
TV (Front)
OPC indicator
SLEEP indicator
POWER indicator
TV (Top/Rear)
AC INPUT terminal
INPUT 1 terminals
SERVICE terminal
INPUT 2 terminals
Antenna/Cable in
INPUT 3 terminals
The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
The examples used throughout this manual are based on the LC-32M44L model.
2–1
LC-32/37M44L
Part Names
2–2
LC-32/37M44L
QUICK REFERENCE
Attaching/Detaching the Stand Setting the TV on the Wall
Before attaching (or detaching) the stand, unplug the AC CAUTION
cord from the AC INPUT terminal.
This TV should be mounted on the wall only with the
Before performing work spread cushioning over the base
AN-37AG5 (SHARP) wall mount bracket. The use of
area to lay the TV on. This will prevent it from being
other wall mount brackets may result in an unstable
damaged.
installation and may cause serious injuries.
CAUTION Installing the TV requires special skill that should
Attach the stand in the correct direction. only be performed by qualified service personnel.
Do not remove the stand from the TV unless using an Customers should not attempt to do the work
optional wall mount bracket to mount it. themselves. SHARP bears no responsibility for
Be sure to follow the instructions. Incorrect installation improper mounting or mounting that results in
of the stand may result in the TV falling over. accident or injury.
Using an optional bracket to mount the TV
1 Confirm that there are 9 screws and a hex key
supplied with the stand unit. You can ask a qualified service professional about
using an optional AN-37AG5 bracket to mount the TV
to the wall.
Carefully read the instructions that come with the
2 Attach the supporting post for the stand unit onto bracket before beginning work.
the base using the box for the stand unit as shown
below.
Hex key 3 Hanging on the wall
AN-37AG5 wall mount bracket.
Screws (See the bracket instructions for details.)
0/5/10/15/20q
LC-32M44L
The center of the display:
11
/ 64 inch (4.0 mm) under
3 Ԙ Insert the stand into the openings on the bottom
of the TV. the "A" position.
ԙ Insert and tighten the 4 screws into the 4 holes LC-37M44L
on the rear of the TV. The center of the display:
1
/ 4 inch (6.0 mm) above
Hex key 2
the "A" position.
Screws Refer to the operation
manual of AN-37AG5 for
details.
2–3
LC-32/37M44L
Appendix
Troubleshooting
Problem Possible Solution
Unit cannot be operated. External influences such as lightning, static electricity, may cause improper operation.
In this case, operate the unit after first turning off the power of the TV or unplugging
the AC cord and replugging it in after 1 or 2 minutes.
Remote control unit does not Are batteries inserted with polarity ( , ) aligned?
operate. Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control sensor?
The TV sometimes makes a This is not a malfunction. This happens when the cabinet slightly expands and
cracking sound. contracts according to change in temperature. This does not affect the TV's
performance.
Troubleshooting-Digital Broadcasting
The error message about reception of broadcast
The example of an error message
Error code Possible Solution
displayed on a screen
No broadcast now. E203 Check the broadcast time in the program guide.
2–4
LC-32/37M44L
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal.
PC Resolution Horizontal Frequency Vertical Frequency VESA Standard
720 x 400 31.5 kHz 70 Hz *
31.5 kHz 60 Hz O
VGA
640 x 480 37.9 kHz 72 Hz O
37.5 kHz 75 Hz O
35.1 kHz 56 Hz O *
37.9 kHz 60 Hz O
PC SVGA 800 x 600
48.1 kHz 72 Hz O
46.9 kHz 75 Hz O *
48.4 kHz 60 Hz O
XGA 1024 x 768 56.5 kHz 70 Hz O
60.0 kHz 75 Hz O
WXGA 1360 x 768 47.7 kHz 60 Hz O
*These 3 formats are not supported by the analog RGB terminal.
2–5
LC-32/37M44L
CHAPTER 3. DIMENSIONS
LC-32/37M44L
Service Manual
[1] DIMENSIONS
LC-32M44L
30 9/ 16 (776) Unit: inch (mm)
(393.8)
15 1/ 2
13 5/ 64
(332)
2 1/ 16
(52)
15 27/ 32 (402)
2 59/ 64 3 45/ 64
7 7/ 8 (200) (74) (94)
4 11/ 32
(110)
7 7/ 8 (200)
9 1/ 16 (230)
LC-37M44L
35 19/ 32 (904)
Unit: inch (mm)
32 15/ 32 (824.4)
23 1/ 32 (585)
25 3/ 32 (637)
18 17/ 64
(463.8)
14 29/ 64 (367)
2 1/ 16
(52)
15 27/ 32 (402)
2 25/ 32 3 3/ 4
7 7/ 8 (200) (71) (95)
3 61/ 64
(100)
(200)
7 7/ 8
9 1/ 16 (230)
3–1
PartsGuide
LC-32/37M44L
PARTS GUIDE
No. S48J1LC32M44L
Note:
The reference numbers on the PWB
LC-32M44L
are arranged in alphabetical order.
MODELS LC-37M44L
CONTENTS
[2] LCD PANEL (NOTE: THE PARTS HERE [10] PACKING PARTS (NOT REPLACEMENT ITEM)
SHOWN ARE SUPPLIED AS AN ASSEMBLY
BUT NOT INDEPENDENTLY.) [11] SERVICE JIG (USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
LC-32/37M44L
[5] NOTE (Conductive cloth tape/Gasket) (LC-32M44L)
Added parts
Conductive Cloth Tape
˴Parts code: ԘPSLDMB359WJZZ Q'ty 1 ԙPSLDMB360WJZZ Q'ty 2
ԚQEARZA123WJZZ Q'ty 3 ԛPSLDMB361WJZZ Q'ty 2
ԜPSLDMB362WJZZ Q'ty 2
Gasket
˴Parts code: ԝPMLT-A533WJZZ Q'ty 1 ԞPMLT-A534WJZZ Q'ty 1
Bond
˴Parts code: ԟZSLCN-098P2KE (One 150g tube)
Apply bond to
Back Light Chassis Apply bond to
1 location.
8 1 location.
8 8
Apply bond to
1 1 location.
2
8 2
Apply bond to
1 location.
Main Shield
3
Main PWB Holder
MAIN Unit
5
Main PWB Holder
7
6
4
5
Attention
When peeling off the conductive cloth tape/gasket for repair, please use the NEW conductive cloth tape/gasket. (When using
the conductive cloth tape/gasket again, keep in mind the decrease in the adhesive power of the conductive cloth tape/gasket.
The purpose of using the NEW conductive cloth tape/gasket is to prevent the conductive cloth tape/gasket from peeling off.)
3
LC-32/37M44L
[6] CABINET AND MECHANICAL PARTS (LC-32M44L)
7
37
1 36
37
30
KEY Unit
1-6 36
1-1 1-5
32
31
1-6 1-5
1-8 38
35
1-7
1-4 38
R/C, LED Unit 46
6
1-3 39
42
1-2 1-7
27 2-2
41
49 48
45 2
49
20
45
40 42
34
26
2-1
5
33 50 21 45
9
44
17
12 43 45
46 25
POWER/INVERTER Unit 46
43 45 29 22
51 23
14
43 28 51 47
45 15
21 47-2 47-3
24 17
19 14
10
12 MAIN Unit 50
13
45
11
43 45
35 4
18 45 47-1
53 47-3
8
45
10 45
11
16 35
4
LC-32/37M44L
5
LC-32/37M44L
[7] NOTE (Conductive cloth tape/Gasket) (LC-37M44L)
Added parts
Conductive Cloth Tape
˴Parts code: ԘPSLDMB359WJZZ Q'ty 1 ԙPSLDMB360WJZZ Q'ty 1
ԚPSLDMB276WJKZ Q'ty 1 ԛPSLDMB375WJKZ Q'ty 1
ԜQEARZA123WJZZ Q'ty 1 ԝPSLDMB361WJZZ Q'ty 2
ԞPSLDMB362WJZZ Q'ty 2
Gasket
˴Parts code: ԟPMLT-A533WJZZ Q'ty 1 ԠPMLT-A534WJZZ Q'ty 1
Bond
˴Parts code: ԡZSLCN-098P2KE (One 150g tube)
Apply bond to
1 location.
10 Apply bond to
1 10 1 location.
10
Apply bond to RA wire 2
1 location.
3
Apply bond to
10 1 location.
10
5 4 Apply bond to
2 locations.
SP wire
Main Shield
9
8
6
7
Attention
When peeling off the conductive cloth tape/gasket for repair, please use the NEW conductive cloth tape/gasket. (When using
the conductive cloth tape/gasket again, keep in mind the decrease in the adhesive power of the conductive cloth tape/gasket.
The purpose of using the NEW conductive cloth tape/gasket is to prevent the conductive cloth tape/gasket from peeling off.)
6
LC-32/37M44L
[8] CABINET AND MECHANICAL PARTS (LC-37M44L)
7 45
35
1-5 1
30 36
KEY Unit
37
36
1-5
37
1-1 INVERTER Unit
1-5
1-5 32
1-7
31
1-5 38
1-8
1-5 50
1-6
38
1-4
R/C, LED Unit 49
39
1-3
6
1-2 1-6 42
2-2
27 41
34 13 2
51 45
20
45
52
40 42
26 2-1 5
33 53 21 45
9 48
44
17
POWER Unit
12 45 46 25
45 46
29
22 15
14 54 23
28 54 47
43 45 12 21
17 47-2 47-3
14 24
14
10 19
MAIN Unit 53
18
43
11 45
45
4
47-1
45
47-3
56
45
8
11 43 10 45
16
43
16
16
7
LC-32/37M44L
8
LC-32/37M44L
[9] SUPPLIED ACCESSORIES
X1 Cable Clamp X2 AC Cord X3 Remote Control Unit Operation Manual
X4
X5
9
LC-32/37M44L
[10] PACKING PARTS (NOT REPLACEMENT ITEM)
S8
S9
S7
S7
S4
S5
S6
S10
S2
S3
S7
S7 S11
S1
10
LC-32/37M44L
11
LC-32/37M44L
SHARP CORPORATION
AV Systems Group
Jun. 2008 CS Promotion Center
TQ2534-S MI. KD Yaita, Tochigi 329-2193, Japan