Professional Documents
Culture Documents
Ampeg Bass Amp Manual
Ampeg Bass Amp Manual
Owner’s Manual
BA Series Bass Guitar Combo
Laite on liitettävä suojakoskettimilla varustettuun The lightning flash with arrowhead symbol within an equilateral
triangle means “electric shock hazard”. It is intended to alert
pistorasiaan. the user to the presence of uninsulated “dangerous” voltage
within the product enclosure, that may be of significant
magnitude to constitute a risk of electric shock to persons.
Apparatet må tilkoples jordet stikkontakt.
The exclamation point within an equilateral triangle means
“Warning/Caution!”. It is intended to alert the user of the
presence of important operating and maintaining (servicing)
Apparaten skall anslutas till jordat uttag. instructions in the literature accompanying the appliance.
2
BA Series Bass Guitar Combo
NOTE: This equipment has been tested Class A/Class B (whichever is applicable)
and found to comply with the limits for a limits for radio noise emissions from digital
Class B digital device, pursuant to part 15 apparatus as set out in the radio interference
of the FCC Rules. These limits are designed regulations of the Canadian Department of
to provide reasonable protection against Communications.
harmful interference in a residential Exposure to extremely high noise levels may
installation. This equipment generates, cause permanent hearing loss. Individuals
uses, and can radiate radio frequency vary considerably in susceptibility to
energy and, if not installed and used in noise-induced hearing loss, but nearly
accordance with the instructions, may everyone will lose some hearing if exposed
cause harmful interference to radio to sufficiently intense noise for a period of
communications. However, there is no time. The U.S. Government’s Occupational
guarantee that interference will not occur Safety and Health Administration (OSHA)
in a particular installation. If this equipment has specified the permissible noise level
does cause harmful interference to radio or exposures shown in the following chart.
television reception, which can be determined According to OSHA, any exposure in excess
by turning the equipment off and on, of these permissible limits could result
the user is encouraged to try to correct in some hearing loss. To ensure against
the interference by one or more of the potentially dangerous exposure to high
following measures: sound pressure levels, it is recommended
• Reorient or relocate the receiving that all persons exposed to equipment
antenna. capable of producing high sound pressure
• Increase the separation between levels use hearing protectors while the
the equipment and the receiver. equipment is in operation. Ear plugs or
protectors in the ear canals or over the
• Connect the equipment into an outlet ears must be worn when operating the
on a circuit different from that to which equipment in order to prevent permanent
the receiver is connected. hearing loss if exposure is in excess of
• Consult the dealer or an experienced the limits set forth here:
radio/TV technician for help. Duration, per Sound Level Typical Example
day in hours dBA, Slow
CAUTION: Changes or modifications to this Response
8 90 Duo in small club
device not expressly approved by Yamaha 6 92
Guitar Group Inc. could void the user’s author- 4 95 Subway Train
ity to operate the equipment under FCC rules. 3 97
2 100 Very loud classical music
1.5 102
This apparatus does not exceed the 1 105 The boss screaming at his minions about manual
deadlines
0.5 110
0.25 or less 115 Loudest parts at a rock concert
Correct disposal of this product: This symbol indicates that this product should not be disposed of with your household waste,
according to the WEEE directive (2012/19/EU) and your national law. This product should be handed over to an authorized
collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have
a possible negative impact on the environment and human health due to potentially hazardous substances that are gener-
ally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling,
please contact your local city office, waste authority, or your household waste disposal service.
3
BA Series Bass Guitar Combo
TABLE OF CONTENTS
4
BA Series Bass Guitar Combo
Introduction
Plus, performance-driven features like integrated DIs and effects loops are perfect
for serious gigging and rehearsal. Portable by design and built for gigging, a protective
all-steel amp chassis, durable double-thick Tolex® and metal corners deliver the durability
you need during transport.
Like all Ampeg products, your BA combo is designed by musicians and built using only
the best of components. Each combo is tested to confirm that it meets our specifications,
and we believe that this combo is the absolute best that it can be.
In order to get the most out of your new combo, please read this manual before
you begin playing. Best of luck in all of your musical endeavors!
BA Series Features:
• Classic Tone
• Legacy Ampeg preamp and tone stack circuits
• Ampeg Ultra Hi/Lo tone shaping*
• Bass Scrambler™ overdrive for SVT grind*
• Perfectly-matched Ampeg Custom™ speakers
• Modern Flexibility
• True 60˚ sound reinforcement monitor angle
• Integrated DIs, effects loops, extension speaker outs*
• Aux in / headphone outs
• Rugged Portability
• Protective all-steel amp chassis
• Impact-resistant metal corners
• Durable double-thick Ampeg classic black Tolex®
• Rugged, braced enclosures
2 4 9
1 5 3 6 7 8 10 11 12
1. INPUT: The signal output from an trying something new. It does not affect
instrument (active or passive) may the signal fed to the aux input.
be connected to this 1/4" input by 8. ULTRA LO: This switch, when engaged,
means of a shielded instrument cable. enhances the amount of low-end
2. –15 dB: Press this switch in to output by 1 dB at 40 Hz and –10 dB
reduce the input signal by 15 dB cut at 500 Hz.
and compensate for higher output [BA-112, BA-115, BA-210]
sources. This attenuation is suited 9. ULTRA HI: This switch, when engaged,
for use with basses that have active enhances the amount of high frequency
electronics or high-output pickups. output by 5 dB at 8 kHz.
3. SCRAMBLER: Engage this switch to [BA-112, BA-115, BA-210]
activate the Bass Scrambler™ overdrive 10. BASS: Use this to adjust the low
circuit. This allows for varying amounts frequency level of the amplifier. The low
of tube-like grind and distortion. frequency output is flat at the center
4. SCRAMBLER LED: This LED position. See pages 10-14 for technical
illuminates green when the Bass specifications.
Scrambler™ overdrive is on. 11. MID: Use this to adjust the midrange
5. DRIVE: Use this to adjust the amount frequency level of the amplifier.
of Bass Scrambler™ overdrive effect. The midrange frequency output is flat
Rotate the control clockwise for a more at the center position. Rotate the control
overdriven sound, or counter-clockwise counter clockwise for a “contoured”
for a less overdriven sound. sound (more distant, less midrange
6. BLEND: Use this to blend the Bass output) or clockwise for a sound which
Scrambler™ affected signal with the really cuts through. See pages 10-14
clean unaffected signal. for technical specifications.
7. VOLUME: Use this to control the 12. TREBLE: Use this to adjust the high
overall output level. It affects the preamp frequency level of the amplifier.
level to speaker and phone outputs. Use The high frequency output is flat
it wisely, and turn it down when making at the center position. See pages
connections, putting on headphones, or 10-14 for technical specifications.
6
BA Series Bass Guitar Combo
14 17
13 14 15 16 18 19 20 21 22
13. AUX LEVEL: Use this to control the 16. EFFECTS SEND JACK: Use this 1/4"
output level of the signal fed to the aux TS unbalanced output to send a line-level
input. Use it wisely, and turn it down output to an external effects processor
when making connections, putting on (for example). The output here is
headphones, or trying something new. affected by all controls except the
aux level.
14. AUX INPUT: The audio output from
line-level sources, such as an iPod®, Use the effects return jack to feed
MP3, or CD player, can connect to the returned processed signals back
either of these inputs. The incoming into the power amplifier.
audio is mixed with the preamp signals, [BA-115, BA-210]
so you can play along to a practice 17. EFFECTS RETURN JACK: Use this
track. 1/4" TS unbalanced input to return the
15. XLR LINE OUT JACK: Typically, you processed line-level output of an external
would connect this post-EQ, balanced effects processor (for example).
output to the balanced input of an The processor could be fed by signals
external mixer, or a recorder. In this from the effects send.
way, you do not have to mic the speaker [BA-115, BA-210]
cabinet in order to add it to the main 18. PHONES: Use this 1/8" TRS stereo
mix, or to record. The level of this signal output to connect your headphones.
is affected by the volume control. The output here is a mix of the line-level
This output can connect to external signals reaching the amplifier, and any
power amplifiers, or powered incoming audio from the aux input jacks.
loudspeakers, as long as they have their Before putting on headphones, make
own input controls to adjust the volume sure the volume and aux controls are
level. turned down, and (if connected) any
[BA-115, BA-210] external audio source has its level turned
down. This will reduce the chance of
hearing damage due to loud volumes.
NOTE: Speakers are muted when
headphones are plugged in.
7
BA Series Bass Guitar Combo
19 20 21 22 23 24
19. HF MUTE: Press this switch in to 24. EXT SPKR OUT: Use this 1/4" TS
mute the high-frequency output. output jack to connect the amplifier
[BA-115, BA-210] to an 8 extension speaker. The
20. FOOTSWITCH: Connect a single internal speaker remains active when
footswitch to this jack for Scrambler an extension speaker is connected.
on/off control. Use a speaker cable with 1/4" TS
[BA-112, BA-115, BA-210] ends only to make the connection.
NOTE: A footswitch may be purchased Do not use instrument cables as
at your local Ampeg Dealer. they may overheat.
Be sure to ask for model #AFP1. [BA-210]
21. ON LED: This LED illuminates red
when the power is on.
22. POWER SWITCH: Use this switch
to turn the overall system power
on or off. Press the top of the switch
to turn on the power, and press the
bottom to turn it off.
23. POWER CONNECTOR: This is
where you connect the supplied
AC power cord.
8
BA Series Bass Guitar Combo
Favorite Settings
9
BA Series Bass Guitar Combo
BA-108 TECHNICAL SPECIFICATIONS
Output Power Rating 20 watts @ 4 ohms, 10% THD+N
INPUT
MUTE POWER
AMPLIFIER 8” WOOFER
20 W 4 OHM
LIMITER
Mono 1/4”
AUX Inputs
Stereo1/8”
PHONES
STEREO 1/8”
AUX LEVEL
10
BA Series Bass Guitar Combo
BA-110 TECHNICAL SPECIFICATIONS
Output Power Rating 40 watts @ 4 ohms, 10% THD+N
BYPASS
SCRAMBLER TONE CONTROL CIRCUITRY
INPUT
FET
PREAMP DRIVE MIX VOLUME TREBLE MIDRANGE BASS
MUTE POWER
AMPLIFIER 10” WOOFER
40 W 4 OHM
LIMITER
Mono 1/4”
AUX Inputs
Stereo1/8”
PHONES
STEREO1/8”
AUX LEVEL
11
BA Series Bass Guitar Combo
BA-112 TECHNICAL SPECIFICATIONS
Output Power Rating 75 watts @ 4 ohms, 10% THD+N
BYPASS
TONE CONTROL TONE CONTROL TONE CONTROL
SCRAMBLER
CIRCUITRY CIRCUITRY CIRCUITRY
INPUT
FOOTSWITCH
POWER
AMPLIFIER 12” WOOFER
75 W 4 OHM
LIMITER
Mono 1/4”
AUX Inputs
Stereo1/8”
PHONES
STEREO 1/8”
AUX LEVEL
12
BA Series Bass Guitar Combo
BA-115 TECHNICAL SPECIFICATIONS
Output Power Rating 150 watts @ 8 ohms, 10% THD+N
BYPASS
TONE CONTROL TONE CONTROL TONE CONTROL
SCRAMBLER
CIRCUITRY CIRCUITRY CIRCUITRY
INPUT LINE
OUT
SEND
EFFECTS POWER
LOOP AMPLIFIER 1” PIEZO
50 W 8 OHM
RETURN MUTE XOVER HF MUTE LIMITER
MONO 1/4”
AUX INPUTS
PHONES
STEREO 1/8” STEREO 1/8” POWER 15” WOOFER
AMPLIFIER 8 OHM
150 W
LIMITER
AUX LEVEL
13
BA Series Bass Guitar Combo
BA-210 TECHNICAL SPECIFICATIONS
Output Power Rating 450 watts @ 4 ohms, 3% THD+N
283 watts @ 8 ohms, 10% THD+N
BYPASS
TONE CONTROL TONE CONTROL TONE CONTROL
SCRAMBLER
CIRCUITRY CIRCUITRY CIRCUITRY
INPUT
SEND
POWER
EFFECTS AMPLIFIER
LOOP 50 W @ 8 ohm 1” TWEETER
8 OHMS
RETURN MUTE XOVER HF MUTE LIMITER
MONO 1/4”
10” WOOFER
AUX INPUTS PHONES 16 OHMS
STEREO 1/8” STEREO 1/8” POWER
AMPLIFIER
283 W @ 8 ohm
450 W @ 4 ohm
LIMITER
AUX LEVEL 10” WOOFER
16 OHMS
EXTERNAL
SPEAKER
8 Ohms minimum
14
BA Series Bass Guitar Combo
Service Information
If you are having a problem with your BA-series combo, you can go to our website
(www.ampeg.com) and click on Support for service information, or call Technical Support
at 1-818-575-3600 Monday-Friday during normal business hours, Pacific Time, to receive
assistance. If you are outside of the U.S., contact your local distributor for technical support
and service.
BA-series combos are covered with a durable fabric-backed vinyl material, so be sure to clean it with
a dry lint-free cloth. Never spray cleaning agents on the BA-series combo. Avoid abrasive
cleansers which would damage the finish.
Ampeg continually develops new products and improves upon existing ones. For this reason, the specifications
and information in this manual are subject to change without notice.
“Ampeg” is a registered trademark of Yamaha Guitar Group Inc. All other brand names mentioned are tradmarks
or registered trademarks of their respective holders and are hereby acknowledged.
www.ampeg.com
©2018 Yamaha Guitar Group Inc.
26580 Agoura Road • Calabasas, CA 91302-1921
Part No. SW1064 Rev. D 07/18
15
012-AB dna 511-AB ,211-AB ,011-AB ,801-AB
launaM s’renwO