Professional Documents
Culture Documents
Boomer M2 C 9850 2181 01e
Boomer M2 C 9850 2181 01e
Boomer M2 C
Equipped with COP 1638, COP 1838ME or COP 2238 rock drills
Coverage area up to 53 m2
www.atlascopco.com
M2
M2
Standard features
»»Rock drill »»Control system
• COP 1638, COP 1838ME or COP 2238 rock drill with • Advanced Rig Control System (RCS) allowing several levels
dual-damping system for optimal consumable life of automation to suit customer requirements
• Pressurized housing and mating surfaces to reduce internal • Standard functions include soft collaring and the anti-jam-
contamination of the rock drill ming function Rotation Pressure Controlled Feed (RPCF)
• Integrated diagnostic and event logging system to assist in
»»Hydraulic boom equipment maintenance
• Interactive operator panel with full-colour display
• BUT 32 heavy-duty boom with double tripod suspension
for accurate hydraulic parallel holding in all directions
»»Carrier
»»Hydraulic feed • Sturdy, articulated carrier with four-wheel drive
• Powered by a 4-cylinder, EPA III/COM III (Tier 3/Stage IIIA)
• BMH 6800-series heavy-duty aluminium feed with high approved diesel engine
bending and torsional resistance for maximum durability • Four jacks for stable set up
• Snap-on stainless steel sleeves and polymer contacts
»»General
• FOPS-approved telescopic protective roof
• Hydraulically driven water booster pump
• Hydraulically driven compressor
• Cable reel
• Working lights
Boomer M2 C
Specifications
ROCK DRILL »»Electrical system
COP 1638 COP 1838ME COP 2238
• Total installed power....................................................158 kW
• Main motors...............................................................2x75 kW
Shank adapter R32/R38/T38 R32/R38/T38 R32/R38/T38
• Voltage.................................................................380–1,000 V
Height over drill centre 88 mm 88 mm 88 mm
• Frequency. ................................................................50–60 Hz
Length without shank 1,008 mm 1,008 mm 1,008 mm • Starting method........................star/delta (1,000 V direct start)
Impact power 16 kW 18 kW 22 kW • Electronic overload protection for electric motors
Impact rate 60 Hz 60 Hz 73 Hz • Percussion hour meter on operator display
Hydraulic pressure 200 bar 230 bar 250 bar • Digital voltmeter/amperage meter in electric cabinet
Rotation system Separate rotation Separate rotation Separate rotation • Phase sequence indicator
Rotation speed 0–340 rpm 0–340 rpm 0–340 rpm
• Earth fault indicator
• Battery charger
Rotation torque, max 640 Nm 640 Nm 640 Nm
• Transformer. ...................................................................8 kVA
Lub. air consump. at 2 bar 6 l/s 6 l/s 6 l/s • Cable reel, diameter................................................. 1,600 mm
Water consumption 1.1 l/s 1.1 l/s 1.1 l/s • Dual controls for cable reel
Weight 170 kg 170 kg 170 kg
Sound level <106 dB(A) <106 dB(A) <106 dB(A)
»»Hydraulic system
FEED • Hydraulic pumps...............2 separate units, one for each boom
BMH 6800 BMH 6812 BMH 6814 BMH 6816 • Pumps unloaded at start
• System pressure, max. ...................................................250 bar
Total length 5,287 mm 5,882 mm 6,502 mm
• Hydraulic oil tank, volume max/min......................... 255/170 l
Drill steel length 3,700 mm 4,310 mm 4,920 mm
• Low oil level indicator
• Oil temperature gauge on oil tank
Hole depth 3,443 mm 4,043 mm 4,668 mm
• Electrical oil filling pump
Weight, incl. drill 601 kg 631 kg 665 kg
• Oil filter indicator
Feed force 20.0 kN 20.0 kN 20.0 kN
• Water cooled oil
• Filtration. ........................................................................ 16 µm
»»Boom • Mineral hydraulic oil
• Big hole drilling system
• Boom............................................................................BUT 32
• Feed extension......................................................... 1,800 mm
• Boom extension....................................................... 1,250 mm »»Carrier
• Parallel holding..........................................................complete
• Feed roll-over.................................................................... 360° • Deutz 4-cylinder, TCD 2013 L04, EPA III/COM III (Tier 3/
• Max. lifting angle..................................................... +65°/–30° Stage IIIA) approved 4-stroke prechamber diesel engine
• Max. swinging angle.........................................................±45° • Power rating at 2,300 rpm. ........................... 120 kW (160 hp)
• Weight, boom only......................................................2,075 kg • Torque at 1,600 rpm.....................................................618 Nm
• Articulated steering................................... ±41° steering angle
• Fixed seat for tramming
»»Air system • Four-wheel drive
• Hydrostatic power steering system
• Hydraulically driven screw compressor. .. Atlas Copco GAR 5 • Hydrodynamic transmission.................................Clark 24000
• Capacity, max at 9 bar. .....................................................26 l/s • Front axle............................................................. Dana 123/90
• Adjustable speed • Rear axle ....................................Dana 123/90, ±8° oscillation
• Air pressure gauge • Automatic differential lock on front axle, limited slip
• Hole blowing kit with 80 l air receiver • Tyres. ......................................................................12.00xR24
• Clearance outside axles................................21° front, 13º rear
• Hydraulic jacks, front . ........................................ 2 extendable
»»Water system • Hydraulic jacks, rear...............................................................2
• Service brakes..............................................2 separate circuits
• Hydraulically driven water booster pump. ....Flygt PXR1607H
• Emergency and parking brakes......................................SAHR
• Water booster pump max capacity at 15 bar.............. 250 l/min • Fuel tank, volume. ........................................................... 100 l
• Min water inlet pressure at 200 l/min, ..............................2 bar • Exhaust catalyser
• Water pressure gauge • Silencer
• Water flow guard • Electric system..................................................................24 V
• Batteries...........................................................2x12 V, 125 Ah
• Tramming lights........................................................... 8x70 W
»»Control system • Working lights......................................................... 2x1,000 W
• Rig Control System (RCS) – versatile and upgradeable to a • Brake lights
• Illuminated stairs for platform..................................... 2x70 W
higher degree of automation
• Fire extinguisher
• One adjustable, electronic control panel with colour display • Central lubrication system
• PC-card for transfer of data and backup settings • Spirit level....................one for longitudinal, one for sideways
• Integrated diagnostic system • Gradeability at max. load on drive wheels. ........................ 1:4
• Separate battery for electronic system • Horn, beacon and reverse alarm
• Shelf for drill bits and tools
Boomer M2 C
SR35-H35-T38 45
Couplings
SR35-R39-T38 45
Thread Diameter Length
R32-R39-T38 45
mm R38 55 170
SR35-R39-T38 45
T38 55 190
SR35-R39-T38 Speedrod 45
mm Rnd 32 Speedrod 51
Rnd 38 Speedrod 64
Optional equipment
»»Rock drill/Drilling • Swingable seat for drilling and tram- rear carrier frame)
ming (one operator panel only) • Exhaust particle filter Unikat
system • Two operator panels for standing • Fire suppression system ANSUL
• Water mist flushing, external water operation only (manual or Checkfire)
and air supply • Fire suppression system FORREX
»»Cabin (manual or automatic)
»»Feed • Large plates for boom frame hydrau-
• FOPS-approved cabin, noise level <80 lic jacks
• Telescopic feed BMHT 6000-series dB(A), height
(max 18 ft) 3,044 mm including:
• Extension drilling set BSH 110 -- Air conditioning unit »»Electrical system
(BMH feeds only) -- Fixed seat • Stainless steel electrical enclosure
• Feed prepared for RAS -- CD-changer • Electric cable type H07RN-F or
• Rod Adding System, RAS -- Boot washing kit Buflex
• Water spraying kit on cradle • Cabin body made of stainless steel • Plug for cable
• Front window, 24 mm • Switch gear
»»Boom • Heating function for air conditioning • Electric outlet for accessories, 16 A
(water transferred) (CE and not for 1,000 V)
• Automatic boom lubrication kit,
• Electrical heater, 1.2 kW, 230 V (CE) • Extra transformer 3-phase, 15kVA
rear part of boom
• Joystick-controlled spotlights left and/ (230/400 V outlet)
or right • Starting method – soft start (not for
»»Software • Swingable seat for drilling and tram- 1000 V)
• ABC Basic ming (one operator panel only)
• ABC Regular • Two operator panels (for standing
• ABC Total operation only)
»»Miscellaneous
• Rig prepared for ABC Total • Service platform, SP2 (not with
• Electronic parallel holding (ABC BMHT feeds or RAS)
»»Air system • Protective roof for service platform
Regular)
• Measure While Drilling (MWD) • Compressor, GAR 30 • Water and air outlet in service
logging and analyzing drill data platform
• Bolt view (ABC Regular and Total) »»Water system • Hose/cable guiding at water/cable
• Rig Remote Access (RRA) • Water hose reel reel
• RRA server • Hydraulic Swellex pump type H1
• Wireless Local Area Network con- for manual installation
nection (WLAN)
»»Hydraulic system • Manual lubrication kit
• Biodegradable hydraulic oil • Rig washing kit
• Heater kit for hydraulic oil tank, diesel • Boot washing kit
»»Protective roof engine and electric motors • Ni-Cr plated piston rods (limitations
• Mounting height -80 mm/+60 exist)
mm/+310 mm • Hydraulic outlet for charging with
• Manual spotlight, left and/or right
»»Carrier
Mini SSE
• Deutz TCD 2013 L06 engine (longer
Boomer M2 C
Measurements
side view
3044
www.atlascopco.com
2303
M2
1958
M2
Illustrations and photos in this brochure may show equipment with optional extras. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer Center for specific information.
801 1800 1940 802
© Copyright 2008, Atlas Copco Rock Drills AB, Örebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or copying of the contents or any part thereof is prohibited.
2906 3740 932
13837 with BMH 6814
Coverage area
1720
6450
6100
3010
1930
200
1310
2245
2690
8200
9000
WEIGHT
gross weight, depending on configuration
08/2008
kg Total 21,500–25,600