Professional Documents
Culture Documents
This material is a property of Samsung Electronics Co., Ltd. Any unauthorized use of this material can be punished under
applicable International and/or domestic law.
- This document cannot be used without Samsung’s Authorization - Confidential
Notice
This guide is intended solely for the Samsung Electronics internal training and may contain
trade secret, industrial technology or privileged and confidential information otherwise
protected under applicable law including the Unfair Competition Prevention and Trade Secret
Protection Act. Any unauthorized dissemination, distribution, copying of use of the information
contained in this guide is strictly prohibited and subject to legal action.
All functionality, features, specifications and other product information provided in this
document including, but not limited to, the benefits, design, pricing, components, performance,
availability, and capabilities of the product are subject to change without notice or obligation.
Samsung reserves the right to make changes to this guide and the product described herein,
at anytime, without obligation on Samsung Electronics to provide notification of such change.
2. H/W
2-1. Disassembly & Assembly
2-2. Parts Diagram (Module & ICs)
2-3. Troubleshooting
2-4. R/F Calibration
3. S/W
3-1. S/W Download
3-2. Key Features
2G/3G LTE
Network
Support Cat11 (600 Mbps Down-Link / 75 Mbps Up-Link )
Connectivity & LBS Bluetooth 5.0, WIFI a/b/g/n/ac, NFC, USB 2.0, MST GPS & Glonass & Beidou
In case of
the back-glass Back-glass Inner tape GH81-15176A
disassembly
Fingerprint Deco WP tape GH02-15669A
CU sheet GH02-15948A
In case of
the damaged
Oring GH81-15238A
gasket at
I/F Connector
** Usage guide of the Power & Current test jig has been uploaded at GSPN. (Power & Current Tester_Rev5_150716.pdf)
- This document cannot be used without Samsung’s Authorization - Confidential
Troubleshooting
No Power (cont’)
Step Check point Result value Defect point
26MHz TRCV (U2004)
7 Check the frequency of TCX2000
If not the correct value X-TAL (TCX2000)
Step6,7
Step5
TCX2000
=26Mhz
** Test a customer’s charger using the Power & PASS Go to the step 1
4
Current test jig TA test mode. FAIL Customer’s Charger
Dust Clean I/F connector
5 Disassemble and check I/F connector visually Damage Replace I/F connector
Normal Go to the step 6
C5123 = 5V Go to the step 7
6 Check the voltage of C5123
If not the correct value may not connected charger
C5165 = 5V Replace the U5008
7 Check the voltage of C5115
If not the correct value Replace the U5001
** Usage guide of the Power & Current test jig has been uploaded at GSPN. (Power & Current Tester_Rev5_150716.pdf)
- This document cannot be used without Samsung’s Authorization - Confidential
Troubleshooting
No Charging
Step 6
Step 6
C5123 = 5V
0000
U5001 C5165 = 5V
U5008
U302 Transceiver
PA200 PAM(Power
Amplitude Module)
Metal sheet
(connect Main Ant.
with PBA)
Main
DEBUG SCREEN STATUS ANTENNA contact ANT. Contact (for main RF)
Same value compare to
normal device.
Step5
Step4
Diversity
ANTENNA contact
Replace the speaker, and also replace the Assy Solved speaker
3
spk-rear to use a new speaker tape. Not solved Go to the next step
Activate the speaker path.
4 - -
(*#0*# → Speaker)
Check the signal at two of speaker contacts. Same signal compared with a
Go to step 6
ANT6002, ANT6003(Using oscilloscope) good PBA
5
Notice : It should be measured when the
speaker path is activated on. No signal Go to step 7
Solved Inductors
Replace inductor at two of speaker
7
L6005, L6006.
No signal Go to step 8
Solved U6002
Replace SPK AMP at speaker
8
U6002
Not solved Go to step 3
Front PBA
ANT6003
NFC_MST ANT ANT6002
L6005
L6006
U6002
SPK AMP
Check the voltage of C7096 = 1.5V If not the correct value LDO(U7061)
6 Notice. It should be measured when the display is
activated on C7096=1.5V Go to the next step
Check the voltage of following chips If not the correct value U7094
(C7099,C7101,C7100) C7099 = 7.3V
7
Notice. It should be measured when the display C7101 = -1.4 ~ -4.4V MAIN CHIP
is activated on C7100 = 4.6V
HDC7001
LCD CONNECTOR U7061
U7062
C7096 C7097
C7099
C7100 C7101
U900
U7094
2 50 ohm
2 GH81-11962E
Termination
3 RF cable
2 GH81-11962D
(Divider to phone)
4 RF cable
1 GH81-11962B
(Instrument to divider)
5 Anyway JIG 1 -
6 Power Supply 1 E3632A
7 RF Equipment 1 CMW500
8 IF cable 1 GH81 – 11962W
7 1
CMW 4 4 Port 7
500 Divider
2 2
Connection PC
Diagram 3 3
6 1
4
P 5 8
/ Anyway PHONE 3
S
2
Entering Path : CAMERA → Live Focus Entering Path : GALLERY → Adjust Background Blur
AP/CP Water
Charger Spec IF Cable RF Cable
Chipset Resistance
Samsung Adaptive
GH81-11962W GH81-11962D (pi : 1.35T) IP 68
Exynos 7885 (9.0V-1.67A)