Professional Documents
Culture Documents
July, 2012
Rev 1.3
HHP Global CS team
HHP EHQ Review
© Samsung Electronics Co., LTD | Confidential
Revision History: This version replaces all previous versions
Date Version Comments
2012-07-23 V1.3 EHQ edit from Initial Version (GT-I9300 Repair Guide Rev 1.2)
Following slides removed as not relevant for this document: (not relevant for the purpose of this document)
Types of NFF
Liquid Ingress
Corrosion
Cracked BGA
Damaged Connector
How to use GSPN
Flux Guide
Oscilloscope Settings – to be released as separate document
1. All functionalities, features, specifications and other product information provided in this document
including, but not limited to, the benefits, design, pricing, components, performance, availability, & capabilities
of the product are subject to change without notice or obligation. Samsung reserves the right to make changes
to this document and the product described herein, at anytime, without obligation on Samsung to provide
notification of such change.
2. This document contains information proprietary to Samsung Electronics. Therefore, it is strictly prohibited to
distribute this document, or parts of it, to unauthorised parties.
OS Android ICS
8M w/LED, BIS,
8M w/LED Faster, High-Quality and Intelligent Camera
Zero Shutter Lag
NO Liquid/Physical
In warranty Damage Check
period
YES
YES NO
Out Of Warranty, Quote for Check software
Check rooted Diagnose fault
YES Repair version & upgrade
NO Or when required
Quote for Repair Return
YES un-
Has unit been Proceed with Fault as
Show record repaired
repaired previously per diagnosed fault
repeat repair within 90 days
NO
RF calibration
YES (only required)
Send to
senior Allocation of repair Another fault
technician diagnosed record
Writing IMEI
on internal
Technician to confirm
system
reported fault
Final test & QC
NO NO
NO
Reported fault If QC pass
No Fault Found Record
confirmed
Result YES
Return to customer
YES Check Accessories
If necessary
Through Settings
1. Go to Settings > About Device > Status
1. Enter into Download Mode: Volume Down + Home + Power, then press Volume Up to continue
You can use the old 7 Pin cable for IMEI writing,
however you must insert the battery into the
handset for supplying power.
Pre-Requisites:
Item File Name Location
Power Supply
GT-I9300 Handset
3) Check ‘IMEI Write’ and ‘IMEI Check’ option, & click ‘IMEI SVC & Repair Option’ to check ‘SVC’ option.
5) Click ‘Port Setting’ in the phone option, & select correct port for IMEI writing.
11. Once the IMEI write process is complete, disconnect the handset and switch off the
equipment
© Samsung Electronics Co., LTD | Confidential 16
Boot Recovery (1/14)
Brief JTAG Process for GT-I9300:
1. First copy the JTAG (bootloader) file to an external micro SD card using a working GT-I9300
2. Insert the micro SD card to the Faulty PBA & copy the bootloader file to the
3. After downloading bootloader file to the defective PBA, rebuild the handset & software update the handset
with full s/w files (Pit, PDA, CSC, Modem)
Pre Requisites:
4. Enter into download mode with the working phone (with micro SD card inserted)
- To enter download mode: press
- a. Volume Down + Home Key + Power.
- b. Volume Up
a b
6. Once connection is established and you can see the COM Port selected as above, click the ‘Start’
button to copy the “GT-I9300_Boot_Loader.tar” to the phone
11. Enter the working phone into download mode and connect to the PC again.
12. Ensure you have a micro SD card inserted into the phone. (2GB minimum requirement)
13. Click Start button to copy the “GT-I9300_Boot_Recovery.tar” file to the micro SD Card.
14. After downloading is complete, disconnect the working phone from the PC & remove micro SD Card
- At this stage, our micro SD card is ready & will be used to recover Bootloader of the faulty PBA
15. Now disassemble the faulty phone. Connect a working OCTA to your faulty PBA.
16. Now insert the micro SD card (which has BOOTLOADER_SDCARD.tar file) which we prepared
previously & insert into the faulty PBA.
17. Short Circuit R313 using tweezers for about 5 seconds after switching on the phone. You must short
circuit R313 before switching on the device (please follow this step and the next in conjunction with
the video supplied)
18. Using the Anyway S102 Jig and the test cable (Part No. GH81-10631A), power up the main PBA
19. After about 7 ~ 8 seconds, the Bootloader file is downloaded from external micro SD card (which you
inserted) into the eMMC of the phone.
20. At this stage you will see this message on the phone display: “SDCARD DOWNLOAD COMPLETED”.
Disconnect the power supply from the main PBA after about 20 seconds.
21. Now you can continue to download All software binary files on to the device (Pit, PDA, CSC, Modem)
QnA:
Q. After flashing the GT-I9300_Boot_Recovery.tar file on the micro SD card, when I insert this micro SD
Card in a good working GT-I9300, I get the below shown message/error
A. This is normal. You may not be able to see the contents of the micro SD card when accessing from
within the handset.
Q. When I insert the prepared micro SD card into laptop/PC, it asks me to format the drive.
A. Please do not format the drive. It is normal operation once you have prepared your micro SD Card
QnA:
Q. When checking the properties of the micro SD card in My Computer, it shows 0 bytes but fully occupi
ed drive. Is this normal?
These problems may occur due to dust inside the connector or around the interface
connector.
2. Pre-requisite
③ Gently clean the inside of the IF connector ④ Blow the IPA excess away with the air gun
using the antistatic brush. from the pin-side of the IF connector.
Warning – Read and understand the MSDS for the IPA product that you are using before use.
Wait until the connector is dry before applying power.
GT-I9300 Galaxy S3
Electronic Components
Guide
SPK Module
Ant. Contact
8M GH59-12159B (for GPS)
CAMERA
Shield Can (for RF performance)
GH96-05593A
Dome key
(for Volume key)
Proximity Sensor
GH96-05758A
Motor(for Vibration)
Home key Touch key
GH31-00585A contact connector
© Samsung Electronics Co., LTD | Confidential 35
SMD parts (TOP side)
HEA700 3711-007071
Ant200 3712-001375
Connector(CAM&SENSOR)
Ant. Contact (for GPS)
LED500 0601-003079
Ant203 3712-001375
Flash LED
Ant. Contact (for BT/WIFI)
HDC601 3711-008157
U207 1205-004510
Connector(RCV & LED & SIDE KEY)
NFC control IC
OSC100 2801-005166
Ant500&501 3712-001373
Oscillator - 26Mhz
Contact (for wireless charging)
UCP300 1205-004511
MOT500&501 3712-001378 CP (Call Processor) + CP PMIC
Motor contact
U706 1203-007269
DC – DC converter (for LCD)
UME300 1108-000472
MCP(Multi Chip Package) Memory U204 1209-002041
Magnetic Sensor
MIC600 3003-001136 KEY500&501 3712-001375
MIC (1st) Touch key contact
© Samsung Electronics Co., LTD | Confidential 37
Assembly & Disassembly Instruction
GT-I9300 Galaxy S3
Diagnostics Guide
Step 5
C558 = 1.0V
C561 = 1.0V
TP(AP_PS_HOLD) > 1.8V
C559 = 1.1V
C556 = 1.0V
OSC100(C505)
Should be 32kHz
Abnormal Settings
Check the settings
2
(airplane mode, Mobile networks)
Normal Go to the next step
Coaxial cable
(connect Rx diversity ant.
with PBA)
GH59-12196A
CHECK SETTINGS
U106 1201-003406
PAM(Power Amplitude
Module)
R200 = 37Mhz
Check the clock of R200 (Same signal compared with BT/WiFi IC (U202)
a good PBA)
5
Notice. It should be measured when the BT/WIFI path
is activated
If not the correct value OSC201
Step4,5
U500(PMIC)
C220
BT/ WIFI IC
R200
OSC201(37Mhz)
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
Solved Settings error
2 Perform factory reset (*2767*3855#)
Not solved Go to the next step
Broken, dust, corrosion Speaker connector
3 Check the speaker connector (HDC600)
Normal Go to the next step
Solved speaker
4 Replace the speaker module (GH59-12159B)
Not solved Go to the next step
Connect the OCTA, and power on with a power
5 - -
supply (power supply voltage : 3.8V ~ 4.2V)
Activate the speaker path
6 - -
(*#0*# → Speaker)
Check the signal of speaker contact Same signal compared with a
(C665,C666) PMIC (U615)
good PBA
7
Notice. It should be measured when the No signal Audio Codec (U605)
speaker path is activated
HDC600
Speaker connector
GH59-12159B
SPK Module
Step 7
C665
C666
U605
Audio Codec
Check the voltage of C735 = 2.2V If not the correct value LDO(U707)
6 Notice. It should be measured when the display is
activated C735=2.2V Go to the next step
Check the voltage of following chips If not the correct value L703,L706,U706
(C713,C712)
7 C713 = 4.6V
Notice. It should be measured when the display is MAIN CHIP
activated C712 = 3.0 ~ 4.4VV
Step 2 Step 5
HDC702
LCD CONNECTOR
C549
C712
C713
C735
Check the I2C Signal of following chips If not the correct value R466,R467,R706
(R466,R467,R706)
7
Notice. It should be measured when the display is Standard I2C Signal – Refer to slide
activated 58. You can also reference it from a MAIN CHIP or PBA
Working PBA
TSP
CONNECTOR
TSP IC
OCTA CONNECTOR
Step6
Step 6 - Resistors
Reference Signal
Ste
Check point Result value Defect point
p
Confirm the defect symptom
1 - -
(*#0*# → Receiver)
Solved Setting error
2 Make a factory reset (*2767*3855#)
Not solved Go to the next step
Broken, dust, corrosion connector
3 Check the receiver connector(HDC601)
Normal Go to the next step
Solved Receiver
4 Replace the receiver module (GH59-12217A)
Not solved Go to the next step
Connect a working OCTA, & power on with a
5 - -
power supply (power supply voltage: 3.8V ~ 4.2V)
Activate the speaker path
6 - -
(*#0*# → Receiver)
Receiver connector
Step4
Receiver GH59-12217A
STATUS LED Lamp
Dome key
(for Volume key)
Microphone
Microphone
Rubber Holder
Step 6
U605
Audio Codec
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
SIM socket or
Broken, dust, corrosion
2 Check the SIM socket & Connector Connector
Normal Go to the next step
Power on with a power supply
3 - -
(power supply voltage : 3.8V ~ 4.2V)
Check the signal of SIM socket Pin 2,3 & 4 3V or 3V clock Go to the next step
(TP 329,330,331)
4
Notice. It should be measured when the phone Call Processor
is switched ON If not the correct value
(UCP300)
Step5
CHECK SETTING
Battery
GH43-03699A
Step 4
GPS Antenna
(FPCB type, in speaker module)
GPS
Antenna Contact
GH59-12159B
Step 5
Step 4