Professional Documents
Culture Documents
0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Removal
Engine removal is not required for this procedure.
1. Disconnect the battery negative terminal. (Refer to Engine and transaxle assembly in this group)
2. Remove the RH front wheel. (Refer to SS group – “Wheel”)
3. Remove the under cover. (Refer to Engine and transaxle assembly in this group)
4. Remove the RH side cover. (Refer to Timing system in this group)
5. Remove the engine cover. (Refer to Engine and transaxle assembly in this group)
6. Remove the air duct and the air cleaner assembly. (Refer to Intake and exhaust system in this group)
7. Loosen the drain plug, and drain the engine coolant. Remove the radiator cap to help drain the
coolant faster. (Refer to Cooling system in this group)
8. Disconnect the radiator upper hose and lower hose. (Refer to Cooling system in this group)
Disconnect the wiring connectors and harness clamps, and then remove the wiring and protectors
from the cylinder head and the intake manifold.
(1) The intake OCV (Oil control valve) connector (A)
9.
1/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
3/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
(13) The MAPS (Manifold absolute pressure sensor) & IATS (Intake air temperature sensor)
connector (A)
10. Disconnect the brake booster vacuum hose (A) and the heater hoses (B).
4/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
11. Disconnect the fuel hose (A) and PCSV (Purge control solenoid valve) hose (B).
5/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
18. Remove the intake CVVT assembly (A) and exhaust CVVT assembly (B).
6/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
When removing the CVVT assembly bolt, hold the camshaft with a wrench to prevent the
camshaft from rotating.
7/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
21. Remove the HLA (Hydraulic lash adjuster) (A) and the swing arm (B).
The HLA and swing arm should be kept together as pairs during storage after removal and
reinstallation.
8/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
9/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
29. Remove the spark plugs (A). (Refer to EE group – “Ignition system”)
10/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Head warpage or cracking could result from removing bolts in an incorrect order.
(2) Lift the cylinder head (A) from the dowels on the cylinder block and place the cylinder head on
wooden blocks on a bench.
Be careful not to damage the contact surfaces of the cylinder head and cylinder block.
Disassembly
Identify, valves and valve springs as they are removed so that each item can be reinstalled in its
original position.
When installing the SST, insert the front support (A) directly into the bolt hole on the
cylinder head.
11/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Inspection
Cylinder Head
1. Inspect for flatness.
Using a precision straight edge and feeler gauge, measure the contacting surface of the cylinder
12/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
13/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
(3) Subtract the valve stem diameter measurement from the valve guide inside diameter
measurement.
If the clearance is greater than specification, replace the valve or the cylinder head.
Margin
[Standard]
Intake: 1.30 mm (0.0512 in.)
Exhaust: 1.26 mm (0.0496 in.)
14/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Valve length
[Standard]
Intake: 102.22 mm (4.0244 in.)
Exhaust: 104.04 mm (4.0961 in.)
[Limit]
Intake: 101.97 mm (4.0146 in.)
Exhaust: 103.79 mm (4.0862 in.)
(5) Check the surface of the valve stem tip for wear.
If the valve stem tip is worn, replace the valve.
3. Inspect the valve seats and the valve guides.
(1) Check the valve seat for evidence of overheating and improper contact with the valve face.
If the valve seat is worn, replace the cylinder head.
(2) Check the valve guide for wear.If the valve guide is worn, replace the cylinder head.
4. Inspect the valve springs.
(1) Using a steel square, measure the out-of-square of valve spring.
(2) Using a vernier calipers, measure the free length of valve spring.
If the free length is not as specified, replace the valve spring.
Valve spring
[Standard]
Free height: 45.93 mm (1.8083 in.)
Out-of-square : Less than 1.5°
15/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Camshaft
1. Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
If the cam lobe height is less than specification, replace the camshaft.
Cam height
Intake: 39.0 mm (1.5354 in.)
Exhaust: 39.0 mm (1.5354 in.)
16/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
(4) Install the bearing caps and tighten the bolts with specified torque.
Tightening torque
M6 bolts:
11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)
M8 bolts:
18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)
17/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
(4) Intake CVVT : Apply approx. 150 kPa (1.5 kgf/㎠, 21 psi ) of compressed air into the unsealed
advance hole to release the lock.
Exhaust CVVT : Apply approx. 150 kPa (1.5 kgf/㎠, 21 psi ) of compressed air into the unsealed
retard hole to release the lock.
Cover the oil paths with a piece of cloth when applying compressed air to prevent oil from
spraying.
(5) Intake CVVT : With compressed air applied, rotate the CVVT into the advance direction
(counterclockwise) within its phasing range and check that the CVVT turns smoothly.
Exhaust CVVT : With compressed air applied, rotate the CVVT into the retard direction
(clockwise) and check that the CVVT turns smoothly.
18/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
(6) Intake CVVT : Rotate the CVVT into the most retarded position (clockwise) and then check that
the CVVT is locked.
Exhaust CVVT : Rotate the CVVT into the most advanced position (counterclockwise) and then
check that the CVVT is locked.
HLA (Hydraulic Lash Adjuster)
With the HLA filled with engine oil, hold A and press B by hand.
If B moves, replace the HLA.
19/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Reassembly
20/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Place the valve springs so that the side coated with enamel faces toward the valve spring
retainer and then installs the retainer.
(3) Using the SST (09222-3K000, 09222-3K100), compress the spring and install the retainer locks.
Before releasing the valve spring compressor, ensure that the retainer locks are correctly in
place after pushing down and releasing the compressor handle 2 ~ 3 times.
When installing the SST, insert the front support (A) directly into the bolt hole on the
cylinder head.
Installation
Apply liquid gasket on the edge of the cylinder block and cylinder head gasket.
21/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Assemble the cylinder head gasket and the cylinder head within 5 minutes after applying
sealant.
2. Place the cylinder head (A) carefully to protect damage to the head gasket during installation.
Tightening torque
1st step:
32.4 ~ 36.3 N.m (3.3 ~ 3.7 kgf.m, 23.9 ~ 26.8 lb-ft)
2nd step: 90~95°
3rd step: 90~95°
22/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Tightening torque:
23/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Tightening torque:
34.3 ~ 39.2 N.m (3.5 ~ 4.0 kgf.m, 25.3 ~ 28.9 lb-ft)
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
24/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
8. Install the oil control adapter (A) with a new gasket (B).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
Tightening torque:
19.6 ~ 23.5 N.m (2.0 ~ 2.4 kgf.m, 14.5 ~ 17.4 lb-ft)
12. Install the HLA (Hydraulic lash adjuster)(A) and the swing arm (B).
(1) When installing HLA, it should be held upright so that engine oil in HLA may not spill and
assured that dust does not adhere to HLA.
(2) HLA should be inserted carefully to the cylinder head not to spill engine oil.
In case of spilling, air bleed should be done in accordance with the air bleed procedure.
Stroke HLA in diesel oil 4 ~ 5 times by pushing its cap while pushing the ball down slightly
with a hard steel wire. (Take care not to severely push a hard steel wire down since ball is
several grams.)
26/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
(4) Place the cam carrier (A) on the cylinder head. The dowel pins on the cam carrier and holes on
the cylinder head should be used as a reference in order to assemble the cam carrier in exact
position.
(5) Fasten the cam carrier bolts.
Tightening torque:
18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)
27/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Tightening torque
M6 bolts:
11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)
28/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
M8 bolts:
18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)
15. Install the intake CVVT assembly (A) and exhaust CVVT assembly (B).
Tightening torque:
64.7 ~ 76.5 N.m (6.6 ~ 7.8 kgf.m, 47.7 ~ 56.4 lb-ft)
When installing the CVVT assembly bolt, hold the camshaft with a wrench to prevent the
camshaft from rotating.
29/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
19. Install the timing chain including the drive belt, the cylinder head cover, the alternator and the
30/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
Tightening torque:
18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)
22. Connect the fuel hose (A) and PCSV (Purge control solenoid valve) hose (B).
23. Connect the brake booster vacuum hose (A) and the heater hoses (B).
24. Install the wiring and protectors on the cylinder head and the intake manifold and then connect the
wiring connectors and harness clamps.
(1) The intake OCV (Oil control valve) connector (A)
31/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
33/35
2014 > G 2.0 MPI > Sistema mecanico de motor > Conjunto culata motor > Valvulas > Procedimientos de reparación
(13) The MAPS (Manifold absolute pressure sensor) & IATS (Intake air temperature sensor)
connector (A)
25. Connect the radiator upper hose and lower hose. (Refer to Cooling system in this group)
26. Install the air duct and the air cleaner assembly. (Refer to Intake and exhaust system in this group)
27. Install the engine cover. (Refer to Engine and transaxle assembly in this group)
28. Install the RH side cover. (Refer to Timing system in this group)
29. Install the under cover. (Refer to Engine and transaxle assembly in this group)
30. Install the RH front wheel. (Refer to SS group – “Wheel”)
31. Connect the battery negative terminal. (Refer to Engine and transaxle assembly in this group)
32. Add all the necessary fluids and check for leaks.
Connect GDS. Check for codes, note, and clear. Recheck.
35/35