Professional Documents
Culture Documents
Hydraulics
each tailored to a particular application or use. This catalog 30 to 15,000 psi, depending on the coupling series, size and
is arranged according to those categories. In each section the materials. Rated pressures as shown in this catalog are
construction of a specific design will be detailed. However, defined by ISO 5598, as “the qualified operating pressures
based on the valving of the coupling, hydraulic couplings which are recommended for a component or a system by
generally fall into one of two groups, either Double Shut-Off or the manufacturer.” Parker “Rated Pressures” have been
Straight-Thru. established on the basis of laboratory tests which include,
but are not limited to, static burst tests and multiple cycle
Double Shut-Off couplings are used extensively when it is
impulse tests. System characteristics such as high cycling
important to minimize fluid loss upon disconnection. Both
rates and high amplitude shocks either hydraulic or
halves of the coupler, the body and the nipple, contain shut-off
mechanical, can reduce the functioning life of a coupling,
valves. These valves open automatically when the body and
even if the system’s nominal pressure falls within the rated
nipple are connected, and close automatically when the two
pressure range of the coupling.
halves are disconnected—keeping fluid loss to a minimum.
For assistance in analyzing your application, contact your
Parker Straight-Thru couplings have no valves in either half
nearest Parker sales office or the Quick Coupling Division
and are ideal for maximum flow application. Their smooth, open
bore offers the lowest pressure drop of any quick disconnect in Minneapolis.
coupling, and allows them to be thoroughly cleaned. Since there Refer to the Safety Guide at the end of this catalog for
are no valves in either half, fluid flow should be shut off before considerations when selecting a Quick Coupling.
the coupling is disconnected. Refer to the Fluid Compatibility Chart (note Table of Contents)
for seal selection assistance for both Double Shut-Off and
Straight-Thru couplings.
B Hydraulics
n
1/4 to 1 Poppet/Ball n Ball Nitrile -40° to +250° F 3000 psi 4000 Series
3/8 to 1/2 Poppet/Ball n Ball Nitrile -40° to +250° F 3000 psi 4200 Series
Non-Spill
3/8 to 1 Flush Face n Ball Nitrile -40° to +250° F 2500 psi NS Series
Nitrile/ EAS/SAE
1/2 Flush Face/Poppet n Ball -40° to +250° F 3000-3625 psi
Polyurethane Adapters
Nitrile/
1/4 to 1 Flush Face n Ball -40° to +250° F 3000-5000 psi FF Series
Polyurethane
Nitrile/
1/4 to 1 Flush Face n Ball -40° to +250° F 3000-5000 psi FEM Series
Polyurethane
1/4 to 1 Flush Face n Ball Fluorocarbon -15° to +400° F 2000 psi FS Series
Materials:
A - Aluminum B - Brass S - Steel S3 - 303 Stainless S6 - 316 Stainless HP - High Pressure
Stainless Steel
B-3 Parker Hannifin Corporation
Quick Coupling Division
Minneapolis, MN
www.parker.com/quickcouplings
*Seal Material Options
To select proper seal materials, see Fluid Compatibility Chart or contact QCD.
Contact QCD for additional seal material options.
Features:
• Accepts ISO 7241-1, Series B compliant nipples
• Poppet valves along with a metal to metal valve stop
maintains valve alignment and prevents flow checking
• Steel, brass, and stainless steel material options
B Hydraulics
• Brass couplers have double O-rings and stainless steel
locking balls
• Steel coupler sleeve and steel nipple body are hardened to
be wear resistant
• Standard end configurations include female pipe and straight
thread ORB
• Optional Sleeve-Lok and alternative seal materials available
Applications include:
• Industrial hydraulic lines
• Food and chemical processing
• Water and coolant lines
• Mobile equipment
• May be used with some gases
Body Size 1/8 1/4 3/8 1/2 3/4 1 1 1/2 2 1/2 1/8 1/4 3/8 1/2 3/4 1 1 1/2 2 1/2
Rated Pressure (psi) Rated Pressure (psi)
Brass 1000 1000 1000 1000 1000 1000 800 800 3000 3700 2700 3500 2200 1500 1500 1200
Stainless 2000 2000 1500 1500 1500 1000 1000 1000 5000 5000 5000 5000 3000 3000 1500 1500
steel
Steel 5000 5000 4000 4000 2500 2000 1000 1000 5000 5000 4000 4000 2500 2000 1500 1500
Steel w/ N/A 5000 4000 4000 3000 3000 N/A N/A 5000 5000 4000 4000 3000 3000 N/A N/A
HD nipple
Seal Temperature Range: Nitrile: -40°F to +250°F (Standard seal for Brass, Steel, & 303 Stainless Steel couplings).
Fluorocarbon: -15°F to +400°F (Standard seal for 316 Stainless Steel couplings).
Other Seal materials: Contact the Division for availability.
acuum Data: 27.4 inches Hg (-0.9 Bar) both connected and disconnected. (1-1/2” and 2-1/2” body size 60 Series couplings are not recommended for service in
V
disconnected mode)
Performance
35
25
Pressure Drop in PSID
1/4"
15
10 1/2"
10
5
5
0 0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 0 2 4 6 8 10 12 14 16 18
Flow in USGPM Flow in USGPM
40
120
Pressure Drop in PSID
35
3/4" 100
Pressure Drop in psid
30
25 80
1" 2-1/2"
20 60
15 1-1/2"
40
10
20
5
0 0
0 10 20 30 40 50 60 70 0 50 100 150 200 250 300
Flow in US gpm
Flow in USGPM
Part Part No. Weight Part No. Weight Thread Overall Wrench Largest
Body Weight Part No. Weight
No. Type 303 Type 316
Size (lbs.) Steel (lbs.) (lbs.) (lbs.) Size Length Flats Diameter
Brass Stainless Stainless
B Hydraulics
1/8 BH1-60 0.16 H1-62 0.16 SH1-62 0.16 SSH1-62Y 0.15 1/8-27 NPTF 1.90 0.68 0.96
1/8 - - H1-62-T4 0.18 SH1-62-T4 0.10 SSH1-62Y-T4 0.17 7/16-20 ORB 2.06 0.68 0.96
1/4 BH2-60 0.32 H2-62 0.30 SH2-62 0.30 SSH2-62Y 0.30 1/4-18 NPTF 2.26 0.81 1.14
1/4 – - H2-62-T6 0.31 SH2-62-T6 0.31 SSH2-62Y-T6 0.31 9/16-18 ORB 2.41 0.81 1.14
3/8 BH3-60 0.43 H3-62 0.40 SH3-62 0.40 SSH3-62Y 0.40 3/8-18 NPTF 2.49 0.88 1.40
3/8 – - H3-62-T8 0.51 SH3-62-T8 0.51 SSH3-62Y-T8 0.51 3/4-16 ORB 2.75 1.00 1.40
1/2 BH4-60 0.80 H4-62 0.73 SH4-62 0.75 SSH4-62Y 0.76 1/2-14 NPTF 2.87 1.12 1.77
1/2 - - H4-62-T10 0.78 SH4-62-T10 0.75 SSH4-62Y-T10 0.78 7/8-14 ORB 3.05 1.12 1.77
3/4 BH6-60 1.31 H6-62 1.30 SH6-62 1.31 SSH6-62Y 1.33 3/4-14 NPTF 3.56 1.31 2.14
3/4 – - H6-62-T12 1.39 SH6-62-T12 1.34 SSH6-62Y-T12 1.40 1-1/16 - 12 ORB 3.56 1.31 2.14
1 BH8-60 1.95 H8-62 1.95 SH8-62 1.95 SSH8-62Y 1.95 1 - 11 1/2 NPTF 4.18 1.62 2.52
1 – - H8-62-T16 1.95 SH8-62-T16 1.95 SSH8-62Y-T16 1.95 1-5/16 - 12 ORB 4.18 1.62 2.52
1-1/2 BH12-60L 4.58 H12-62L 4.70 SH12-62L 4.68 SSH12-62LY 4.68 1-1/4 - 11 1/2 NPTF 4.86 2.38* 3.00
1-1/2 BH12-60N 4.58 H12-62N 4.70 SH12-62N 4.68 SSH12-62NY 4.68 1-1/2 - 11 1/2 NPTF 4.86 2.38* 3.00
1-1/2 – 4.61 H12-62-T20 4.72 SH12-62-T20 4.71 SSH12-62Y-T20 4.71 1-5/8 - 12 ORB 4.86 2.38* 3.00
1-1/2 – 4.61 H12-62-T24 4.72 SH12-62-T24 4.71 SSH12-62Y-T24 4.71 1-7/8 - 12 ORB 4.86 2.38* 3.00
2-1/2 BH2016-60 11.06 H2016-62 10.58 SH2016-62 – SSH2016-62Y – 2 - 11 1/2 NPTF 5.57 3.75 4.10
2-1/2 BH2020-60 11.42 H2020-62 10.91 SH2020-62 – SSH2020-62Y – 2 1/2 - 8 NPTF 6.04 3.75 4.10
2-1/2 BH2024-60 – H2024-62 – SH2024-62 – SSH2024-62Y – 3 - 8 NPTF 6.69 4.00 4.35
* This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker Coupler.
† Largest diameter on Brass is 2.96” across Hex Corners
‡ Hex on 303 Stainless is 2.50 in.
B Hydraulics
3/4 50001-218-0010 4148001 1/2 H67F-62K H4-62 H67F-63K H4-63
1 50001-222-0010 4158001 1/2 BH67F-60K BH4-60 BH67F-61K BH4-61
1-1/2 50001-124-0010 (Valve) 1/2 SH67F-62K SH4-62 SH67F-63K SH4-63
1-1/2 50001-138-0260 (Fitting) 1/2 SSH67F-62KY SSH4-62Y SSH67F-63KY SSH4-63Y
1-1/2 50001-224-0010 (Body 2 req.) 3/4 H67G-62K H6-62 H67G-63K H6-63
2-1/2 50001-133-0010 (Valve) 3/4 BH67G-60K BH6-60 BH67G-61K BH6-61
2-1/2 50001-234-0260 (Fitting) 3/4 SH67G-62K SH6-62 SH67G-63K SH6-63
2-1/2 50001-333-0010 (Body) 3/4 SSH67G-62KY SSH6-62Y SSH67G-63KY SSH6-63Y
1 H67J-62K H8-62 H67J-63K H8-63
1 BH67J-60K BH8-60 BH67J-61K BH8-61
1 SH67J-62K SH8-62 SH67J-63K SH8-63
1 SSH67J-62KY SSH8-62Y SSH67J-63KY SSH8-63Y
Body Coupler Dust Plug Coupler Dust Plug Nipple Dust Cap Nipple Dust Cap
Size Aluminum Rubber Aluminum Rubber
1/8 H1-65 H1-65M H1-66 H1-66M
1/4 H2-65 H2-65M H2-66 H2-66M
3/8 H3-65 H3-65M H3-66 H3-66M
1/2 H4-65 H4-65M H4-66 H4-66M
3/4 H6-65 H6-65M H6-66 H6-66M
1 H8-65 H8-65M H8-66 H8-66M
1-1/2 H12-65 - H12-66 -
2-1/2 H20P-65 - H20P-66 -
Features:
• Accepts ISO 7241-1, Series B compliant nipples
• Poppet valves along with a metal to metal valve stop
maintains valve alignment and prevents flow checking
• Brass couplers have double O-rings and stainless steel
B Hydraulics
locking balls
• Standard end configuration is female pipe thread
Applications:
• Steam systems
• Cleaning equipment
* This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker Coupler.
Features:
• Accepts ISO 7241-1, Series A compliant nipples
• Poppet valves and a metal perch to maintain valve
alignment and prevent flow checking
• Coupler sleeve and nipple body are hardened to be damage
resistant
B Hydraulics
• Standard end configurations include female pipe and
straight thread ORB
• Protective zinc plating with clear trivalent
chromate finish
Applications include:
• Snow plows
• Truck trailer connections
• Mobile applications
• Attachments
Performance:
6600 Series (1/4") 6600 Series (3/8"& 1/2")
Test Fluid: Oil - 150 SUS Test Fluid: Oil - 150 SUS
25
45
40
20 35
Pressure Drop in PSID
30
Pressure Drop in PSID
1/2"
15 25
1/4" 3/8"
20
10
15
10
5
5
0
0 0 2 4 6 8 10 12 14 16 18
0 0.2 0.4 0.6 0.8 1 1.2
Flow in USGPM
Flow in USGPM 6600 Series (3/4" & 1")
Test Fluid: Oil - 150 SUS
50
45
40
Pressure Drop in PSID
35
1"
30
3/4"
25
20
15
10
0
0 10 20 30 40 50 60 70
Flow in USGPM
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
Body Weight
Dust Plug (Coupler) Color/Material Dust Cap (Nipple)
Size (lbs.)
1/4 H1-65M Black Rubber H1-66M .02
B Hydraulics
3/8 TR-37 Black Rubber TR-37 .04
1/2 5205-4M Black Rubber 5209-4M .04
3/4 6659-12M Black Rubber 6657-12M .06
1 6659-16M Black Rubber 6657-16M .08
Features:
• Sizes 1/4” - 4”
• Available in steel, brass, aluminum and 316 stainless steel
• Standard seal material is nitrile with other options available
• Optional sleeve lock helps to prevent accidental
Applications include: disconnection
• Industrial hydraulic lines • Double-shut-off version has low pressure drop
• Water and coolant lines • Manually operated sleeve provides secure connection
• Mobile equipment
Ball Bearing
Two -Piece Body Postive Ball-Lock Sleeve Lock
Construction Design
O-Ring and Back-Up
Jet Stream
Valve Design Hardened Localized Poppet Has Non-Shift Wide Choice
Sleeve Induction Metal-to-Metal Valve of End-Fittings
Hardened
PH Series Version
Stop
Land
Performance
PH Series H Series
Valved and Valved (Double Shut-Off) Valved and Valved (Double Shut-Off)
Valved and Valved (Double Shut-off) Valved and Valved (Double Shut-off)
Flow Rate (LPM) Flow Rate
FLOW RATE(LPM)
(LPM)
FLOW RATE (LPM)
2271.00
2649.50
3785.00
3028.00
3406.50
1514.00
1892.50
1135.50
1135.50
378.50
757.00
265.00
302.80
340.70
265.00
227.10
340.70
757.00
227.10
302.80
378.50
189.30
113.60
151.40
189.30
113.60
151.40
26.50
34.07
22.71
37.85
75.70
30.28
26.50
30.28
75.70
15.14
34.07
37.85
22.71
11.36
18.93
18.93
15.14
11.36
3.79
7.57
7.57
3.79
B Hydraulics
200 13.79
200 13.79
100 6.90
100 6.90 90 6.21
90 6.21 80 5.52
80 5.52 70 4.83
70 4.83 4.14
60
60 4.14
50 3.45
50 3.45
PR ESSUR E LO S S ( B A R)
P R ES S UR E LOSS ( PSI )
Pressure Loss (PSI)
40 2.76
PRESSU RE L O SS (BA R)
30 2.07
30 2.07
20 1.38
20 1.38
/4"
/2"
"
"
"
"
1/4
3/4
3/8
1"
1/2
2"
Pressure
1-1
"
1-1
"
"
3/4
1/2
3/8
1"
10 .69
9 .62
10 .69 8 .55
9 .62 7 .48
8 .55
7 6 .41
.48
6 .41 5 .34
5 .34 4 .27
4 .27
3 .21
3 .21
2 .14
2 .14
1 .07
1
60
400
4
20
200
9
50
70
80
100
300
700
1000
2
8
3
90
800
900
40
500
600
7
10
30
1 .07
1
8
9
6
100
7
300
4
200
2
10
20
80
40
70
90
50
60
Flow Rate
(MiL-H-6083 (GPM)
OIL @ 90°F ± 5°F)
FLOW RATE (GPM)
Flow Rate (GPM)
(MiL-H-6083 OIL @ 90°F ± 5°F) (MIL-H-6083 oil @ 90°F ± 5°F)
(MIL-H-6083 oil @ 90°F ± 5°F)
S V H C 6 - SPK
3785.00
2271.00
2649.50
3028.00
3406.50
1135.50
1514.00
1892.50
227.10
340.70
757.00
265.00
378.50
302.80
151.40
113.60
189.30
26.50
22.71
75.70
34.07
30.28
37.85
11.36
15.14
18.93
3.79
7.57
300 20.69
Seals:
Blank = Nitrile (Code A) 200 13.79
V = Fluorocarbon
E = Ethylene Propylene 100
90
6.90
6.21
80 5.52
Spare Parts/Repair Kits 70
60
4.83
4.14
50 3.45
Coupling Body Size:
P RE
S (PSI)
E L O S(PSI)
40 2.76
Pressure
6 = 3/8"
S S U R E L O SS
30 2.07
8 = 1/2"
Loss
12 = 3/4"
20 1.38
PR E SSU R
4"
Pressure
2"
Loss
"
16 = 1"
"
"
"
1/4
3/4
3/8
2"
1/2
1"
/
1-1
(B AR )(bar)
1-1
N = Nipple 5 .34
4 .27
Series: 3 .21
H = Poppet valve or plain/unvalved
PH1 = Poppet valve with pressure relief feature
2 .14
Type:
1
V = Valved
.07
1
200
700
7
40
50
100
400
600
300
800
900
3
8
9
10
20
30
90
500
1000
4
60
70
80
B Hydraulics
1/4 - - VHC4-2F Valved 1/8-27 NPTF 1.65 1.00 0.88
1/4 APHC4-4F BPHC4-4F PHC4-4F Non-Valved 1/4-18 NPTF 1.34 1.02 0.88
1/4 AVHC4-4F BVHC4-4F VHC4-4F Valved 1/4-18 NPTF 1.65 1.19 1.00
1/4 - - VHC4-4EF Valved 7/16-20 UNF 1.80 1.02 0.88
3/8 APHC6-6F BPHC6-6F PHC6-6F Non-Valved 3/8-18 NPTF 1.50 1.19 1.00
3/8 AVHC6-6F BVHC6-6F VHC6-6F Valved 3/8-18 NPTF 1.90 1.19 1.00
3/8 - - VHC6-6EF Valved 9/16-18 UNF 2.20 1.19 1.00
1/2 - BPHC8-8F PHC8-8F Non-Valved 1/2-18 NPTF 1.62 1.39 1.19
1/2 AVHC8-8F BVHC8-8F VHC8-8F Valved 1/2-18 NPTF 2.09 1.39 1.19
1/2 - - VHC8-8EF Valved 3/4-16 UNF 2.19 1.39 1.19
3/4 - BPHC12-12F PHC12-12F Non-Valved 3/4-18 NPTF 1.91 1.73 1.50
3/4 - BVHC12-12F VHC12-12F Valved 3/4-18 NPTF 2.42 1.73 1.50
3/4 - - VHC12-12EFV Valved 1-1/16 - 12 UNF 2.92 1.73 1.50
1 - BPHC16-16F PHC16-16F Non-Valved 1 - 11-1/2 NPTF 2.07 2.17 1.88
1 - BVHC16-16F VHC16-16F Valved 1 - 11-1/2 NPTF 2.67 2.17 1.88
1 - - VHC16-16EF Valved 1-5/16 - 12 UNF 2.94 2.17 1.88
1-1/4 - BPHC20-20F PHC20-20F Non-Valved 1-1/4 - 11-1/2 NPT 2.28 2.31 2.00
1-1/4 - BVHC20-20F VHC20-20F Valved 1-1/4 - 11-1/2 NPT 3.54 2.31 2.00
1-1/2 - BPHC24-24F PHC24-24F Non-Valved 1-1/2 - 11-1/2 NPT 2.57 2.89 2.50
1-1/2 - BVHC24-24F VHC24-24F Valved 1-1/2 - 11-1/2 NPT 3.27 3.18 2.75
2 - BPHC32-32F PHC32-32F Non-Valved 2 - 11-1/2 NPT 2.48 3.75 3.25
2 - BVHC32-32F VHC32-32F Valved 2 - 11-1/2 NPT 3.92 4.33 3.75
Part Valved or
Body Largest Wrench
Number Non-Valved Port End Length (in)
Size Diameter Flats
Stainless Steel (Plain)
B Hydraulics
Valved or
Body Part Largest Wrench
Non-Valved Port End Length (in)
Size Number Diameter Flats
(Plain)
B Hydraulics
1/4 SVHC4-4M Valved 1/4-18 NPT 2.09 1.02 0.88
3/8 SVHC6-6M Valved 3/8-18 NPT 2.19 1.19 1.00
1/2 SVHC8-8M Valved 1/2-18 NPT 2.57 1.39 1.19
3/4 SVHC12-12M Valved 3/4-18 NPT 2.88 1.73 1.50
1 SVHC16-16M Valved 1 - 11-1/2 NPT 3.21 2.17 1.88
Valved or
Body Part Largest Wrench
Non-Valved Port End Length (in)
Size Number Diameter Flats
(Plain)
1/4 VHC4-4EM Valved 7/16-20 UNF 2.80 1.02 0.88
3/8 VHC6-6EM Valved 9/16-18 UNF 2.24 1.19 1.00
1/2 VHC8-8EM Valved 3/4-16 UNF 2.46 1.39 1.19
3/4 VHC12-12EM Valved 1-1/6 - 12 UNF 3.05 1.73 1.50
Valved or
Body Part Largest Wrench
Non-Valved Port End Length (in)
Size Number Diameter Flats
(Plain)
3/8 VPHC6-6F Valved 3/8-18 NPTF 1.90 1.19 1.00
1/2 VPHC8-8F Valved 1/2-14 NPTF 2.09 1.39 1.19
3/4 VPHC12-12EF Valved 1-1/16 - 12 UNF 2.92 1.73 1.50
3/4 VPHC12-12F Valved 3/4-14 NPTF 2.42 1.73 1.50
Valved or
Body Part Largest Wrench
Non-Valved Port End Length (in)
Size Number Diameter Flats
(Plain)
B Hydraulics
1/4 SPHN4-2F Non-Valved 1/8-27 NPSF* 1.11 0.62 0.56
1/4 SVHN4-2F Valved 1/8-27 NPSF* 1.59 1.00 0.56
1/4 SPHN4-4F Non-Valved 1/4-18 NPSF* 1.32 0.73 0.63
1/4 SVHN4-4F Valved 1/4-18 NPSF* 1.59 1.02 0.88
3/8 SPHN6-6F Non-Valved 3/8-18 NPSF* 1.52 0.94 0.81
3/8 SVHN6-6F Valved 3/8-18 NPSF* 1.84 1.19 1.00
1/2 SPHN8-8F Non-Valved 1/2-18 NPSF* 1.72 1.15 2.00
1/2 SVHN8-8F Valved 1/2-18 NPSF* 1.98 1.39 1.19
3/4 SPHN12-12F Non-Valved 3/4-18 NPSF* 1.92 1.37 1.19
3/4 SVHN12-12F Valved 3/4-18 NPSF* 2.29 1.73 1.50
1 SPHN16-16F Non-Valved 1 - 11-1/2 NPSF* 2.10 1.73 1.50
1 SVHN16-16F Valved 1 - 11-1/2 NPSF* 2.55 2.17 1.88
1-1/4 SPHN20-20F Non-Valved 1-1/4 - 11-1/2 NPTF 2.22 2.17 1.88
1-1/4 SVHN20-20F Valved 1-1/4 - 11-1/2 NPTF 3.41 2.31 1.88
1-1/2 SPHN24-24F Non-Valved 1-1/2 - 11-1/2 NPTF 2.44 2.46 2.13
1-1/2 SVHN24-24F Valved 1-1/2 - 11-1/2 NPTF 3.11 3.18 3.75
2 SPHN32-32F Non-Valved 2 - 11-1/2 NPTF 2.60 3.18 2.75
2 SVHN32-32F Valved 2 - 11-1/2 NPTF 3.72 4.33 3.75
Valved or
Body Part Largest Wrench
Non-Valved Port End Length (in)
Size Number Diameter Flats
(Plain)
1/4 SPHN4-2M Non-Valved 1/8-27 NPT 1.22 0.64 0.56
1/4 SPHN4-4M Non-Valved 1/4-18 NPT 0.78 0.65 0.56
1/4 SVHN4-4M Valved 1/4-18 NPT 2.03 1.02 0.88
3/8 SPHN6-6M Non-Valved 3/8-18 NPT 0.98 0.80 0.69
3/8 SVHN6-6M Valved 3/8-18 NPT 2.13 1.19 1.00
1/2 SPHN8-8M Non-Valved 1/2-18 NPT 1.01 1.02 0.88
1/2 SVHN8-8M Valved 1/2-18 NPT 2.46 1.39 1.19
3/4 SVHN12-12M Valved 3/4-18 NPT 2.75 1.73 1.50
1 SVHN16-16M Valved 1 - 11-1/2 NPT 3.09 2.17 1.80
1-1/4 SVHN20-20M Valved 1-1/4 - 11-1/2 NPT 3.46 2.31 2.00
Valved or
Body Part Largest Wrench
Non-Valved Port End Length (in)
Size Number Diameter Flats
(Plain)
B Hydraulics
1/4 VHN4-4EM Valved 7/16-20 UNF 2.02 1.02 0.88
3/8 VHN6-6EM Valved 9/16-18 UNF 2.24 1.19 1.00
1/2 VHN8-8EM Valved 3/4-16 UNF 2.35 1.39 1.19
3/4 VHN12-12EM Valved 1-1/6 - 12 UNF 2.92 1.73 1.50
Valved or
Body Part Largest Wrench
Non-Valved Port End Length (in)
Size Number Diameter Flats
(Plain)
1/2 VPHN8-8F Valved 1/2-14 NPTF (Female) 1.98 1.39 1.19
1/2 VPHN8-8EM Valved 3/4-16 UNF (Male) 2.35 1.39 1.19
Body Coupler Dust Plug Coupler Dust Plug Nipple Dust Cap Nipple Dust Cap Nipple Pressure
Size Plastic Aluminum Plastic Aluminum Cap
1/4 PDP-4 AMPH-4 PDC-4 ADCH-4 MCH-4
3/8 PDP-6 AMPH-6 PDC-6 ADCH-6 MCH-6
1/2 PDP-8 AMPH-8 PDC-8 ADCH-8 MCH-8
3/4 PDP-12 AMPH-12 PDC-12 ADCH-12 MCH-12
1 PDP-16 AMPH-16 PDC-16 ADCH-16 MCH-16
1-1/4 - AMPH-20 - ADCH-20 MCH-20
1-1/2 - AMPH-24 - ADCH-24 MCH-24
2 - AMPH-32 - ADCH-32 MCH-32
2-1/2 - AMPH-40 - ADCH-40 MCH-40
3 - AMPH-48 - ADCH-48 MCH-48
Features:
• Vacuum capability
• Available in a variety of materials
• Wide range of sizes
• Nitrile is standard seal material, other options available
B Hydraulics
Applications include:
• Aircraft fabrication
• Plastic molding
• Horizontal boring and dewatering
EA Series Specifications
Force to Connect (Valved and Valved) Spillage on Disconnect (Valved and Valved)
Body
Size Internal Force to With 10 psi Internal With 50 psi Pressure
Pressure (psi) Connect (lbs) Pressure (cc or ml) (cc or ml))
1/4 200 50 1.2 1.5
3/8 200 60 1.4 2.5
1/2 200 95 4.2 4.6
3/4 100 95 10.5 11.6
Pressure ratings were established under static pressure conditions. Therefore, pressure ratings for any given flow, pressure surge and/or vibration
may vary from those ratings.
Performance
EA Series Valved & Valved EA Series Valved & Plain
(Double Shut-off) (Single Shut-off)
Flow Rate (LPM) Flow Rate (LPM)
227.10
265.00
302.80
378.50
340.70
113.60
151.40
189.30
227.10
265.00
302.80
378.50
340.70
113.60
151.40
189.30
30.28
37.85
75.70
22.71
26.50
34.07
15.14
11.36
18.93
30.28
37.85
75.70
22.71
26.50
34.07
11.36
15.14
18.93
3.79
7.57
3.79
7.57
300 20.69 300 20.69
B Hydraulics
100 6.90 100 6.90
90 6.21 90 6.21
80 5.52 80 5.52
70 4.83 70 4.83
60 4.14 60 4.14
50 3.45 50 3.45
40 2.76 40 2.76
30 2.07 30 2.07
20 1.38 20 1.38
"
"
"
"
"
"
"
"
3/8
1/4
1/4
3/8
3/4
1/2
3/4
1/2
10 .69 10 .69
9 .62 9 .62
8 .55 8 .55
7 .48 7 .48
6 .41 6 .41
5 .34 5 .34
4 .27 4 .27
3 .21 3 .21
2 .14 2 .14
1 .07 1 .07
7
1
9
10
20
50
80
30
40
60
70
90
100
2
5
6
3
8
4
9
10
20
50
80
30
40
60
70
90
100
2
7
8
4
5
6
3
Flow Rate (GPM) Flow Rate (GPM)
(88 ssu (18CSt oil) (88 ssu (18CSt oil)
Repair Kits
EA Series Repair Kits and Replacement Parts S V EA C 8 - SPK
Body
Part Number Description Seal Material Seals:
Size
Blank = Nitrile (Code A)
1/2 VEAC8-SPK Coupler Valve Repair Kit Nitrile V = Fluorocarbon
1/2 VEAN8-SPK Nipple Valve Repair Kit Nitrile E = Ethylene Propylene
Spare Parts/Repair Kits
1/4 EA4-58AS Coupler Interface Seal Aflas
Coupling Body Size:
1/2 EA8-58V Coupler Interface Seal Fluorocarbon 4 = 1/4" 8 = 1/2”
3/4 EA12-55A Valve Seal Nitrile 6 = 3/8" 12 = 3/4”
Coupling Half:
3/4 EA12-58A Coupler Interface Seal Nitrile
C = Coupler
N = Nipple
Series:
EA
Type:
V = Valved
P = Plain (without valve)
Material:
Blank = Steel, clear trivalent plating
A = Aluminum, clear anodized
B = Brass
S = 316 Stainless Steel
Optional Seal Materials for Couplers and Valved Nipples
(add code to part number)
Code Description Part Number Example
suffix V Fluorocarbon seal material VEAN4-4FV
suffix E Ethylene Propylene seal material (EPR) VEAC6-6ME
suffix AS Aflas seal material VEAC6-6FAS
Contact QCD for availability and additional options.
To select proper seal materials, see Fluid Compatibility Chart or contact QCD.
1/4 BPEAC4-4F PEAC4-4F 1/4-18 NPTF SPEAC4-4F 1/4-18 NPSF Non-Valved 1.33 1.13 0.88
1/4 BVEAC4-4F VEAC4-4F 1/4-18 NPTF SVEAC4-4F 1/4-18 NPSF Valved 1.61 1.13 0.88
3/8 BPEAC6-6F PEAC6-6F 3/8-18 NPTF - - Non-Valved 1.58 1.31 1.00
3/8 BVEAC6-6F VEAC6-6F 3/8-18 NPTF - - Valved 1.86 1.31 1.00
1/2 BPEAC8-8F PEAC8-8F 1/2-14 NPTF - - Non-Valved 1.70 1.44 1.19
1/2 BVEAC8-8F VEAC8-8F 1/2-14 NPTF SVEAN8-8F 1/2-14NPSF Valved 2.09 1.44 1.19
3/4 BPEAC12-12F - 3/4-14 NPTF SPEAN12-12F 3/4-14 NPSF Non-Valved 2.41 1.88 1.50
3/4 BVEAC12-12F VEAC12-12F 3/4-14 NPTF SVEAN12-12F 3/4-14 NPSF Valved 1.91 1.88 1.50
B Hydraulics
1/4 - - - SVEAN4-2F 1/8-27 NPSF Valved 1.61 1.00 0.88
1/4 BPEAN4-4F PEAN4-4F 1/4-18 NPTF SPEAN4-4F 1/4-18 NPSF Non-Valved 1.33 0.73 0.62
1/4 - VEAN4-4F 1/4-18 NPTF SVEAN4-4F 1/4-18 NPSF Valved 1.61 1.00 0.88
3/8 BPEAN6-6F PEAN6-6F 3/8-18 NPTF - - Non-Valved 1.58 0.94 0.81
3/8 BVEAN6-6F VEAN6-6F 3/8-18 NPTF - - Valved 1.86 1.15 1.00
1/2 BPEAN8-8F PEAN8-8F 1/2-14 NPTF - - Non-Valved 1.70 1.15 1.00
1/2 BVEAN8-8F VEAN8-8F 1/2-14 NPTF SVEAN8-8F 1/2-14NPSF Valved 2.09 1.31 1.19
3/4 BPEAN12-12F - 3/4-14 NPTF SPEAN12-12F 3/4-14 NPSF Non-Valved 2.05 1.37 1.19
3/4 BVEAN12-12F VEAN12-12F 3/4-14 NPTF SVEAN12-12F 3/4-14 NPSF Valved 2.29 1.73 1.50
Body Coupler Dust Plug Coupler Dust Plug Nipple Dust Cap Nipple Dust Cap Nipple Pressure
Size Plastic Aluminum Plastic Aluminum Cap
1/4 PDP-4 AMPE-4 PDC-4 ADCE-4 MCE-4
3/8 PDP-6 AMPE-6 PDC-6 ADCE-6 MCE-6
1/2 PDP-8 AMPE-8 PDC-8 ADCE-8 MCE-8
3/4 PDP-12 AMPE-12 PDC-12 ADCE-12 MCE-12
Features:
• Rated pressures up to 6000 psi
• Poppet valves have captive seals to minimize seal washout
• Steel material with standard nitrile seals
B Hydraulics
Applications:
• Industrial hydraulic lines
• Mobile equipment
Specifications
Body Size 1/4 1/2 3/4
Rated Pressure (PSI) 6,000 6,000 4,500
Rated Flow (GPM) 3 12 28
Temperature Range (Nitrile Seals) -40° to +250°F
Performance
SM Series (1/4") SM Series (1/2" & 3/4")
Test Fluid: Oil - 200 SUS Test Fluid: Oil - 200 SUS
25 35
30
20
25
Pressure Drop in PSID
15
20
1/2"
1/4" 15
10
3/4"
10
5
5
0 0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 0 5 10 15 20 25 30 35 40
Flow in USGPM Flow in USGPM
B Hydraulics
1/4 SM-251-6FP 3/8-18 NPTF 2.24 1.06 0.94 0.28
1/4 SM-251-6FB G3/8 BSPP 2.24 1.06 0.94 0.26
1/4 SM-251-6FO 9/16-18 ORB 2.24 1.06 0.75 0.25
1/2 SM-501-8FP 1/2-14 NPTF 3.00 1.56 1.25 0.70
1/2 SM-501-8FB G1/2 BSPP 3.00 1.56 1.25 0.74
1/2 SM-501-8FO 3/4-16 ORB 3.16 1.56 1.25 0.70
1/2 SM-501-12FP 3/4-14 NPTF 3.07 1.56 1.37 0.81
1/2 SM-501-12FB G3/4 BSPP 3.16 1.56 1.37 0.85
3/4 SM-751-12FO 1 1/16-12 ORB 3.89 2.22 1.62 1.78
3/4 SM-751-12FP 3/4-14 NPTF 3.77 2.22 1.62 1.83
3/4 SM-751-12FB G3/4 BSPP 3.89 2.22 1.62 1.88
3/4 SM-751-16FP 1-11 1/2 NPTF 3.98 2.22 1.62 1.84
3/4 SM-751-16FB G 1 BSPP 3.98 2.22 1.62 1.89
3/4 SM-751-16FO 1-5/16 - 12 ORB 3.98 2.22 1.62 1.89
* This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker Coupler.
Body
Nipple Dust Cap Color/Material Coupler Dust Plug
Size
1/4 N/A Plastic PL-25
1/4 CR-25 Black Rubber PR-25
1/4 C-25 Aluminum P-25
B Hydraulics
Features:
• Rated pressures up to 5000 psi
• Smooth flow path with minimal pressure drop
• Heat treated steel nipple and heavy duty sleeve withstand
pressure surges
• Couplings have protective zinc with clear trivalent chromate
B Hydraulics
finish
• Standard end configurations include female pipe and
straight thread ORB
• Alternative seal materials available
Applications:
• Industrial hydraulic lines
• Mobile equipment
1-1/2"
Temperature Range (std seals) -40° to +250°F
25
1"
20
15
10
0
0 20 40 60 80 100 120 140
Flow in USGPM
Couplers
Body
Part Number Thread Size Length Largest Diameter Wrench Flats Weight (lbs.)
Size
1 HP-1001-16FP 1 11-1/2 NPSF 3.95 2.38 1.62 2.10
B Hydraulics
Nipples
* This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker Coupler.
Features:
• 1/2” size accepts ISO 5675 universal tips
• Basic operation where coupler sleeve is manually
retracted to allow connection with male tip
• Critical parts are hardened
B Hydraulics
• Ball and poppet valve options
• Protective zinc plating with clear trivalent
chromate finish
Applications include:
• Hydraulic Loaders
• Add-on hydraulic circuits
• Hydraulic tools
Performance:
4000 Series (1/4", 3/8", 1/2") 4000 Series (3/4" & 1")
Test Fluid: Oil - 200 SUS Test Fluid: Oil - 200 SUS
70 90
80
60
70
3/4"
Pressure Drop in PSID
50
Pressure Drop in PSID
1/2" 60
1/4"
40
50
3/8" 1"
30 40
30
20
20
10
10
0
0
0 2 4 6 8 10 12 14 16 18
0 10 20 30 40 50 60 70
Flow in USGPM
Flow in USGPM
1/4 4050-2P-T8M 3/4-16 ORB (Male) Poppet 1.80 1.06 0.88 0.21
1/4 4050-T6 9/16-18 ORB Poppet 2.18 1.06 0.88 0.27
1/4 4050P-T6* 9/16-18 ORB Poppet 2.43 1.33 0.88 0.33
3/8 4050-3P 3/8-18 NPTF Poppet 2.31 1.33 0.94 0.51
1/2 4050-4 1/2-14 NPTF Ball 2.60 1.50 1.06 0.58
1/2 4050-4P 1/2-14 NPTF Poppet 2.60 1.50 1.06 0.58
1/2 4050-5 3/4-14 NPTF Ball 2.69 1.50 1.13 0.71
1/2 4050-5P 3/4-14 NPTF Poppet 2.69 1.50 1.13 0.71
1/2 4050-15 3/4-16 ORB Ball 2.81 1.50 1.06 0.64
1/2 4050-15P 3/4-16 ORB Poppet 2.81 1.50 1.06 0.64
1/2 4050-16 7/8-14 ORB Ball 2.75 1.50 1.06 0.59
1/2 4050-16P 7/8-14 ORB Poppet 2.75 1.50 1.06 0.59
1/2 4050-29BSPP 1/2-14 BSPP Ball 2.68 1.50 1.06 0.59
3/4 4150-5 3/4-14 NPTF Ball 3.06 1.87 1.38 1.00
1 4050-6P 1-11 1/2 NPTF Poppet 3.84 2.08 1.63 1.89
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
4050 Series Replacement O-Rings 4000 Series Dust Caps and Plugs
Body
Material Part Number Durometer
Size
1/4 Nitrile 50001-113-0260 90
3/8 Nitrile 50001-116-0260 90
1/2 Nitrile 50001-211-0260 90
3/4 Nitrile 50001-215-0010 70
Body Dust Plug Dust Cap Weight
Color/Material
1 Nitrile 50001-218-0260 90 Size (Coupler) (Nipple) (lbs.)
B Hydraulics
1/4 5205-2M Black Rubber 5209-2M .02
3/8 5205-3M Black Rubber 5209-3M .03
1/2 5205-4M Black Rubber 5209-4M .04
1/2 5005-4 Steel w/Chain 5009-4 .21
1/2 5205-4M-BU Blue Rubber 5209-4M-BU .04
1/2 5205-4M-GR Green Rubber 5209-4M-GR .04
1/2 5205-4M-RE Red Rubber 5209-4M-RE .04
1/2 5205-4M-YE Yellow Rubber 5209-4M-YE .04
3/4 5205-5M Black Rubber 5209-5M .05
1 5205-6M Black Rubber 5209-6M .06
The 4200 Series brings to the industry a proven design for use
on agricultural machinery, construction equipment, and other
rugged applications where a breakaway feature is desirable.
Features:
• 1/2” size accepts ISO 5675 universal tips
• Grooves in sleeve to accommodate retaining rings for
bulkhead mounting
• One-handed push-to-connect operation when coupler is
clamp mounted
B Hydraulics
Applications include:
• Hydraulic Loaders
• Add-on hydraulic circuits
• Implement breakaway
• Hydraulic tools
70
60
Body Dust Plug Dust Cap Weight
Color/Material
Pressure Drop in PSID
B Hydraulics
1/2 4250-4 1/2-14 NPTF Ball 2.68 1.50 0.94 0.55
1/2 4250-4P 1/2-14 NPTF Poppet 2.68 1.50 0.94 0.55
1/2 4250-15 3/4-16 ORB Ball 2.68 1.50 0.94 0.55
1/2 4250-15P 3/4-16 ORB Poppet 2.68 1.50 0.94 0.55
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
Features:
• Rated pressure up to 2500 psi
• Positive valve stop prevents flow checking
• Heat treated steel nipple and heavy duty sleeve withstand
B Hydraulics
pressure surges
• Standard sleeve lock guards against accidental
disconnection
• Couplings have protective zinc with clear trivalent
chromate finish
• Standard end configurations include female pipe, straight
thread ORB, and BSPP
• Alternative seal materials available
Applications:
• Hydraulic hand tools
• Utility equipment
• Mining equipment
45
Specifications
40 Body Size 3/8 1/2 3/4 1
35 Rated Pressure (psi) 2,500
Pressure Drop in PSID
0
0 2 4 6 8 10 12 14 16 18
Flow in USGPM NS Series Dust Plug/Caps
1"
15 3/4 NR-75
3/4" 1 NR-100
10
0
0 10 20 30 40 50 60 70
Flow in USGPM
Couplers
B Hydraulics
3/8 NS-371-6FB G3/8 BSPP 2.10 1.13 1.06 0.38
3/8 NS-371-8FO 3/4-16UNF 2.20 1.13 1.06 0.40
1/2 NS-501-8FP 1/2-14 NPSF 2.88 1.56 1.25 0.84
1/2 NS-501-8FB G1/2 BSPP 2.95 1.56 1.25 0.74
1/2 NS-501-10FO 7/8-14UNF 2.97 1.56 1.25 0.80
3/4 NS-751-12FP 3/4-14 NPSF 3.19 1.96 1.56 1.48
3/4 NS-751-12FB G3/4 BSPP 3.38 1.96 1.56 1.54
3/4 NS-751-12FO 1 1/16-12UN 3.51 1.96 1.56 1.58
1 NS-1001-16FP 1-11 1/2 NPSF 3.70 2.25 1.75 2.35
1 NS-1001-16FB G 1 BSPP 3.81 2.25 1.75 2.36
1 NS-1001-16FO 1 5/16-12UN 3.81 2.25 1.75 2.36
Nipples
* This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker Coupler.
Standard Port Configurations
FP - Female Pipe Thread
FO - Female Straight Thread
FB - Female British Standard Parallel Pipe
Optional Seal Materials:
(add code to part number)
Code Description Part Number Example
suffix -E5 Ethylene Propylene seal material (EPR) NS-502-8FP-E5
suffix -E4 Fluorocarbon seal material NS-502-8FP-E4
Contact QCD for availability and additional options.
To select proper seal materials, see Fluid Compatibility Chart or contact QCD.
Features:
• Adapts flush, non-spill valving to / from poppet style
• Global interchangeability with other ISO 16028 and ISO
7241-A compliant couplings
B Hydraulics
Applications include:
• Skid loader attachments
50
E A S – 500
1/2" Body Size
Pressure Drop in PSID
40
Male Half of Adapter
E – FEM Series (ISO 16028 Standard)
30
1/2" S – 6600 Series
20
Adapter Series
Specifications
Flush Face End Flush Face End
Body
Rate Pressure (psi) Rated Flow (gpm) Temperature Range Spillage (ml) Air Inclusion (ml)
Size
max. per disconnect max. per connect
1/2 3625 12 -40º to +250º F .020 .070
Adapters
Body Largest
Part Number Thread Size Length Wrench Flats
Size Diameter
1/2 EAS-500 N/A 3.36 1.38 1.50
1/2 SAE-500 N/A 3.00 1.25 1.48
Features
• Flush, non-spill valving
• Hardened steel sleeves and nipple bodies
B Hydraulics
• Locking sleeve
• Blow-out resistant seal
• Connect-under-pressure FC nipple option
• Protective zinc plating with clear trivalent chromate finish
Applications include:
• Hydraulic tools
• Mobile equipment
• Industrial hydraulics
40
20 35
Pressure Drop in PSID
1/2" 30
15 1"
3/8" 25
1/4" 3/4"
20
10
15
5 10
0 0
0 2 4 6 8 10 12 14 16 18 0 10 20 30 40 50 60 70
Flow in USGPM Flow in USGPM
FF Series Specifications
Body Rated Pressure Rated Flow Temperature Spillage (ml) max. Air Inclusion (ml) Body Sleeve Seal
Size (psi) (gpm) Range per disconnect max. per connect Material Type Material
1/4 5000 3 .015 .020
3/8 3000 6 .015 .020
Nitrile/
-40º to +250ºF Push to
1/2 3000 12 .080 .070 Steel Polyure-
Connect
thane
3/4 3000 28 .150 .100
1 3000 50 .200 .150
FF Series Couplers
FF Series Nipples
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
B Hydraulics
1/4” Nipple FF-252-KIT FF-252-KIT-E4 FF-252-KIT-E5 –
1/4” Coupler FF-251-KIT FF-251-KIT-E4 FF-251-KIT-E5 FF/FS-251-TOOL
3/8” Nipple FF-372-KIT FF-372-KIT-E4 FF-372-KIT-E5 –
3/8” Coupler FF-371-KIT FF-371-KIT-E4 FF-371-KIT-E5 FF/FS-371-TOOL
3/4” Nipple FF-752-KIT FF-752-KIT-E4 FF-752-KIT-E5 –
3/4” Coupler FF-751-KIT FF-751-KIT-E4 FF-751-KIT-E5 FF/FS-751-TOOL
1” Nipple FF-1002-KIT FF-1002-KIT-E4 FF-1002-KIT-E5 –
1” Coupler FF-1001-KIT FF-1001-KIT-E4 FF-1001-KIT-E5 FF/FS-1001-TOOL
Features:
• Connect-under-pressure nipple
• Flush, non-spill valving
• Hardened locking surface
• Blow-out resistant seal
• Protective zinc plating with clear trivalent chromate finish
Applications include:
• Hydraulic tools
FC Series Specifications 60
Test Fluid: Oil - 200 SUS
40
(psi) Pressure (gpm) discon- max. per
Capabilty nect connect 30
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
Features
• Flush, non-spill valving
• Global interchangeability with other ISO 16028
compliant couplings
B Hydraulics
• Hardened steel sleeves and nipple bodies
• Optional locking sleeve
• Connect-under-pressure FEC nipple option
• Protective zinc plating with clear trivalent
chromate finish
Applications include:
• Skid loader attachments
Materials of Construction • Hydraulic tools
Body: Steel
Finish: Zinc with clear trivalent chromate
Valve: Flush face valving
Seal: Polyurethane and Nitrile
Performance FEM Series (1/4", 3/8" & 1/2") FEM Series (5/8", 3/4" & 1")
Test Fluid: Oil - 150 SUS Test Fluid: Oil - 150 SUS
30.00 45.00
40.00
25.00
35.00
1/4"
Pressure Drop in PSID
1/2"
Pressure Drop in PSID
20.00 30.00
3/4"
25.00
15.00 1"
20.00
3/8"
5/8"
10.00 15.00
10.00
5.00
5.00
0.00 0.00
0.00 2.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 0.00 10.00 20.00 30.00 40.00 50.00 60.00 70.00 80.00
Coupled Length
Body Coupler Largest Wrench Weight
Port End Length (when connected to
Size Part Number Diameter Flats (lbs.)
corresponding nipple)
1/4 FEM-251-4FP-NL 1/4-18 NPSF 1.96 3.98 1.16 27mm 0.52
B Hydraulics
Coupled Length
Body Coupler Largest Wrech Weight
Port End Length (when connected to
Size Part Number Diameter Flats (lbs.)
corresponding nipple)
1/2 FEM-501-10BMF-NL 7/8-14 UNF 4.04 7.24 1.54 1.25 1.13
1/2 FEM-501-10BMS-NL 1-14 UNS 4.04 7.24 1.54 1.25 1.13
Coupled Length
Body Nipple Largest Wrench Weight
Port End Length (when connected to
Size Part Number Diameter Flats (lbs.)
corresponding coupler)
B Hydraulics
1/4 FEM-252-4FP 1/4-18 NPSF 1.71 3.98 0.96 22mm 0.20
1/4 FEM-252-6FO 9/16-18 NPSF 1.95 4.06 0.96 22mm 0.19
3/8 FEM-372-6FP 3/8-18 NPSF 2.48 4.43 1.26 30mm 0.40
3/8 FEM-372-8FO 3/4-16 UNF 2.48 4.67 1.26 30mm 0.41
1/2 FEM-502-8FP 1/2-14 NPSF 2.77 5.09 1.38 1.25 0.54
1/2 FEM-502-8FO 3/4-16 UNF 2.77 5.09 1.38 1.25 0.54
1/2 FEM-502-10FO 7/8-14 UNF 2.77 5.09 1.38 1.25 0.54
1/2 FEM-502-12FO 1 1/16-12 UN 3.02 5.59 1.38 1.25 0.54
5/8 FEM-622-12FO 1 1/16-12 UN 3.09 5.64 1.57 36mm 0.72
3/4 FEM-752-12FP 3/4-14 NPSF 3.38 6.00 1.97 46mm 1.17
3/4 FEM-752-12FO 1-1/16 12 UN 3.38 6.20 1.974 46mm 1.20
1 FEM-1002-16FP 1-11 1/2 NPSF 3.85 6.79 2.36 55mm 1.94
1 FEM-1002-16FO 1-5/16 12 UN 3.85 6.79 2.36 55mm 1.90
Coupled Length
Body Nipple Largest Wrench Weight
Port End Length (when connected to
Size Part Number Diameter Flats (lbs.)
corresponding nipple)
1/2 FEM-502-10BMF 7/8-14 UNF 3.85 7.24 1.38 1.25 .84
1/2 FEM-502-10BMS 1-14 UNS 3.85 7.24 1.38 1.25 .84
Standard Port Configurations: FP - Female Pipe Thread FO - Female Straight Thread BMF - Bulkhead Flare BMS - Bulkhead Face Seal
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
Applications
Parker FEC Series nipple provide connect-under-pressure
capability with up to 3000 PSI of trapped pressure in the nipple
and are ideal for applications where residual pressure makes
reconnect difficult. Utilized primarily in the construction
equipment market, FEC Series products are commonly found
on hydraulic attachments used in skid steer applications. The
FEC Series mates with the FEM Series interface ISO 16028
couplers.
Features:
B Hydraulics
• Connect-Under-Pressure nipple
• Hardened locking surface
• Steel construction, Chromium-6 Free plating
for corrosion resistance
• Anti blowout bonded nipple seal
• Flush face valving
Connect Under Pressure Operation Performance FEC Series (1/2", 5/8", 3/4")
Test Fluid: Oil - 200 SUS
FEC Series products operate slightly different from traditional 80
non-spill couplings. With no pressure in the coupler and up
to 3000 PSI of trapped pressure in the nipple, begin to couple 70
40
1/2"
FEC Series Specifications 30
Coupled Length
Body Largest Wrench Weight
Part Number Mating Half Port End Length (when connected to
Size Diameter Flats (lbs.)
corresponding nipple)
1/2 FEC-502-8FP FEM-501 1/2-14 NPSF 3.50 5.82 1.22 1.125 –
1/2 FEC-502-10FO FEM-501 7/8-14 UNF 3.50 5.82 1.22 1.125 –
1/2 FEC-502-12FO FEM-501 1 1/16-12 UNF 3.79 6.36 1.65 1.500 –
5/8 FEC-622-12FO FEM-621 1 1/16-12 UN 3.39 5.94 1.65 1.500 –
3/4 FEC-752-12FO FEM-751 1 1/16-12 UN 3.76 6.58 1.65 1.500 –
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
Features:
• Rated pressure up to 10,000 psi
• Push to connect operation
B Hydraulics
• Red finish on nipple body and coupler sleeve
• Standard sleeve lock guards against accidental disconnection
• Not interchangeable with lower pressure flush face
couplings
• Standard end configurations include female pipe, male pipe,
and BSPP threads
• Alternative seal materials available
Applications:
• Hydraulic crimpers, cutters, benders, clamps, wedges
• Rescue equipment
• High pressure test equipment
30
Temperature Range -40° to +250° F
25
3/8" Spillage (ML)
.020
20 (max. per disconnect)
Air Inclusion (ML)
15 .070
(max. per connect)
10
0
Materials of Construction
0 1 2 3 4 5 6 7 8 9 Body Steel
Flow in USGPM
Finish Chromium-6 Free plating
Valve Flush Face Valves
Seal Anti blow-out Nitrile/PTFE bonded seal (nipple only)
Couplers
Nipples
Standard Port Configurations: FP - Female Pipe Thread MP - Male Pipe Thread FB - Female British Parallel Pipe
Body Size Coupler Dust Cap - Rubber Nipple Dust Cap - Rubber
3/8 NR-50 NR-37
Features:
• Flush, non-spill valves enable ease of cleaning
• 316 stainless steel material for chemical compatibility
• Push to connect operation
B Hydraulics
• Fluorocarbon standard seal material with options available
Applications include:
• Chemical dispensing systems
• Chemical processing
• Food processing
• Corrosive media transfer
Materials of Construction
Machined Parts: Stainless Steel, AISI type 316
Springs: Stainless Steel, AISI type 316.
Locking Balls: 1/4 - 3/8”: 302 SS;
1/2 - 3/4”: 316 SS
1”: 440 SS
Backup Washers: PTFE
Elastomer Seals: Fluorocarbon is standard.
Wide range is available. Performance Flow Data
FS Series (1/4", 3/8", 1/2")
Test Fluid: Water
30
Specifications
25
Rated Rated Spillage (ml) Air Inclusion
Body 1/2"
Pressure Drop in PSID
Standard Port Configurations: FP - Female Pipe Thread MP - Male Pipe Thread FO - Female Straight Thread
* This dimension represents the portion of the nipple that is exposed when the nipple and coupler are connected.
FS Repair Kits
Replacement Seals
TOOL Spline tool for No Suffix Fluorocarbon Seals
B Hydraulics
Coupler Repair E5 Ethylene Propylene (EPR)
E35 Perfluoroelastomer (Contact Factory for Seal Options).
Features:
• Connect under residual pressure up to 5000 psi
• Disconnect under residual pressure up to 2500 psi
• High impulse resistance
B Hydraulics
Applications include:
• Mobile drill rigs
• Oil field equipment
• Umbilical lines
• High impulse mobile circuits
• Excavator attachments
D D
W1
W1 L W1
B Hydraulics
L L
W2
W2
W2
Largest
Body Coupler Wrench Flats Wrench Flats Weight
Port End Bolt Thread Size Length (in) Diameter
Size Part Number W1 (mm) W2 (in) (lbs.)
(in)
3/4 FET-751-16SF Flange Head - 7.60 2.31 55 2 4.17
3/4 FET-751-16SFP Flange Pad 7/16 - 14 UNC 5.45 2.31 55 2-3/4 4.82
1 FET-1001-20SF Flange Head - 7.78 2.75 65 2-3/16 5.44
1 FET-1001-20SFP Flange Pad 1/2 - 13 UNC 5.83 2.75 65 3 6.90
1-1/2 FET-1501-24SF Flange Head - 9.83 3.75 85 2-5\8 11.37
1-1/2 FET-1501-24SFP Flange Pad 5/8 - 11 UNC 6.82 3.75 85 2-5\8 13.31
D
D
W1
B Hydraulics
L L
W2
W1
W1 W2
W2
Largest
Body Nipple Wrench Flats Wrench Flats Weight
Port End Bolt Thread Size Length (in) Diameter
Size Part Number W1 (mm) W2 (in) (lbs.)
(in)
3/4 FET-752-16SF Flange Head - 6.32 2.31 55 2 3.10
3/4 FET-752-16SFP Flange Pad 7/16 - 14 UNC 4.74 2.31 55 2-3/4 4.33
1 FET-1002-20SF Flange Head - 6.70 2.75 65 2-3/16 4.71
1 FET-1002-20SFP Flange Pad 1/2 - 13 UNC 5.27 2.75 65 3 6.78
1-1/2 FET-1502-24SF Flange Head - 7.77 3.75 75 2-5\8 8.08
1-1/2 FET-1502-24SFP Flange Pad 5/8 - 11 UNC 5.94 3.75 75 2-5\8 12.17
B Hydraulics
Body Nipple Coupler
Size Dust Cap Dust Plug
3/8 FET3DC-01 FET3DP-01
1/2 FET5DC-01 FET5DP-01
5/8 FET6DC-01 FET6DP-01
3/4 FET7DC-01 FET7DP-01
1 FET10DC-01 FET10DP-01
1-1/2 FET15DC-01 FET15DP-01
Features:
• Rated pressures up to 3000 psi
• Thread to connect operation
B Hydraulics
Applications:
• Submersible pumps
• Oil field equipment
• Dump trailers
Performance 6100 Series (1/2" & 3/4")
Test Fluid: OIL 150 SUS • Engine test stands
100
• Bulk liquid transfer
90
80
Pressure Drop in PSID
70
3/4"
60
50
40
Specifications
30
1/2" Body Size 3/4 3/4 1 1 - 1/4 1 - 1/2
20
20
10
0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
Flow in USGPM
B Hydraulics
3/4 6100-08 6120-08 1/2-14 NPTF 5.20 2.12
3/4 6100-12 6120-12 3/4-14 NPTF 5.32 2.00
1 6100-16 6120-16 1-11 1/2 NPTF 5.99 3.19
1 1/4 6100-20 6120-20 1 1/4-11 1/2 NPTF 6.48 4.25
1 1/2 6100-24 6120-24 1 1/2-11 1/2 NPTF 6.80 6.13
Couplers - Wingnut
Nipples
Mounting Flanges
Body Part Number Bolt Hole Bolt Circle
Size Steel Diameter Diameter
3/4 6107-08 (1 piece) .208 2.13
1 6107-16 (1 piece) .208 2.38
1 1/4 6107-20 (2 piece) .208 2.63
1 1/2 6107-24 (2 piece) .281 3.25
Features:
• Accepts ISO 5675 universal tips
B Hydraulics
• Connect under system pressure on the coupler side
and residual pressure on the nipple side
• Sleeve designed to accommodate bracket mounting
• One-handed push-to-connect operation when coupler
is clamp mounted
• 1/2” body size couplers are compatible with 5001-4
and 5006-4 breakaway clamps
• Critical parts are hardened
• Protective zinc plating with clear trivalent chromate finish
Applications include:
• Tractors
• Mid-sized agricultural equipment
• Agricultural attachments requiring breakaway
60
50
Pressure Drop in PSID
40
1/2"
30
20
10
0
0 2 4 6 8 10 12 14 16 18
Flow in USGPM
Optional Seal Materials:
(add code to part number)
Code Description Part Number Example
suffix W Ethylene Propylene seal material- EPR (Couplers) 8250-15W
suffix Y Fluorocarbon seal material (Couplers) 8250-15Y
suffix Z Neoprene seal material (Couplers) 8250-15Z
Contact QCD for availability and additional options.
To select proper seal materials, see Fluid Compatibility Chart or contact QCD.
1/2 8250-15 3/4-16 ORB Poppet 3.29 1.50 0.87 0.63 8200-15
1/2 8250-16 7/8-14 ORB Poppet 3.29 1.50 0.87 0.63 8200-16
Body Weight
Dust Plug (Coupler) Color/Material Dust Cap (Nipple)
Size (lbs.)
1/2 5205-4M Black Rubber 5209-4M .04
1/2 5005-4 Steel w/Chain 5009-4 .21
1/2 5205-4M-BU Blue Rubber 5209-4M-BU .04
1/2 5205-4M-GR Green Rubber 5209-4M-GR .04
1/2 5205-4M-RE Red Rubber 5209-4M-RE .04
1/2 5205-4M-YE Yellow Rubber 5209-4M-YE .04
Features:
• Accepts ISO 5675 universal tips
B Hydraulics
• Premier connect under pressure coupling
• Locked valves prevent flow checking
• Functionally can replace a double shut-off quick coupling and
two high pressure ball valves
• Protective zinc plating with clear trivalent chromate finish
Applications include:
• Mobile equipment
• Industrial hydraulics
• Not recommended for use with gaseous or compressible media
80
70
60
Pressure Drop in PSID
50
1/2"
40
30
20
10
0
0 2 4 6 8 10 12 14 16 18
Flow in USGPM
Body
Coupler Dust Cover Color/Material Nipple Dust Cap Weight (lbs.)
Size
1/2 9507-4-1 Black Rubber 5209-4M .04
Features:
• Accepts ISO 5675 universal tips
B Hydraulics
• Manual, threaded actuation, connect under pressure coupling
• Protective zinc plating with clear trivalent chromate finish
Applications include:
• Lubrication systems
• Hydraulic tools
• Attachments
60
50
Pressure Drop in PSID
40
1/2"
30
20
10
0
0 2 4 6 8 10 12 14 16 18
Flow in USGPM
Body
Dust Plug (Coupler) Color/Material Dust Cap (Nipple) Weight (lbs.)
Size
1/2 5205-4M Black Rubber 5209-4M .04
1/2 5205-4M-BU Blue Rubber 5209-4M-BU .04
1/2 5205-4M-GR Green Rubber 5209-4M-GR .04
1/2 5205-4M-RE Red Rubber 5209-4M-RE .04
1/2 5205-4M-YE Yellow Rubber 5205-4M-YE .04
1/2 5005-4 Steel w/Chain 5009-4 .21
Features:
• Connect under residual pressure
• Thread-to-connect
• Up to 5,000 psi (345 bar) rated pressures
B Hydraulics
• Rugged steel construction with Zinc Trivalent
Chromate plating
• Stainless steel construction also available
• Wide range of sizes
• Nitrile is standard seal material, other options available
• DBP version is “Fire Safe” rated to API 16D
Applications include:
• Cranes
• Power tongs
• Horizontal boring and dewatering
75 Series Specifications
Body Size 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4
Spillage (cc) 8 16 31 64 141 204 320 400
Air Inclusion (cc) 12 25 48 98 205 368 480 610
Snap-tite
250
75 Series 28.25
600
10000
800
3000
300
400
2500
7000
900
1000
5000
6000
8000
100
200
250
700
150
2000
500
9000
1500
4000
INTERNAL PRESSURE (psig)
Performance
INTERNAL PRESSURE
Internal Pressure (bar)
(bar) FLOW RATE(LPM)
Flow Rate (lpm)
3028.00
2271.00
3785.00
2649.50
3406.50
1892.50
1514.00
1135.50
413.79
265.00
378.50
303.00
689.66
206.90
482.76
344.83
340.70
620.69
757.00
227.00
551.72
172.41
275.86
189.30
137.93
103.45
151.40
113.60
48.28
41.38
68.97
37.90
27.59
62.07
75.70
10.34
55.17
34.48
20.69
17.24
13.79
6.90
/4"
/2"
/2"
"
6000 678.00 60
1"
4.14
3/4
2"
1-1
3"
1-1
4"
2-1
B Hydraulics
PRESSURE
2"
(psi)
(inchpounds)
Pressure Loss
LOSS(PSI)
1-1/2"
TORQUE
1-1/4"
Torque (N.m)
1500 169.50
1"
Pressure Loss
3/4"
Torque (inch
LOSS(bar)
900 9 .62
PRESSURE
(N.m.)
800 90.40 8 .55
TORQUE
(bar)
500 56.50 5 .34
400 45.20 4 .27
300
500
700
900
10
70
800
40
400
80
30
600
20
60
90
100
200
1000
50
10000
600
800
3000
300
400
2500
7000
900
1000
100
5000
6000
8000
150
200
250
700
2000
500
9000
1500
4000
75 Series Couplers
3/4” size
Part Part
Body Length Largest Wrench
B Hydraulics
Number Port End Number Port End
Size (in) Diameter Flats
Steel 316 Stainless Steel
3/4 75C12-12F 3/4-14 NPSF S75C12-12F 3/4-14 NPSF 2.84 2.06 1.31
3/4 75C12-12F-DBP 3/4-14 NPSF - - 2.84 2.06 N/A
1 75C16-16F 1-11-1/2 NPSF S75C16-16F 1-11-1/2 NPSF 3.45 4.25 1.69
1 75C16-16F-DBP 1-11-1/2 NPSF - - 3.45 4.25 N/A
1-1/4 75C20-20F 1-1/4-11-1/2 NPTF S75C20-20F 1-1/4-11-1/2 NPT 4.40 4.75 2.00
1-1/4 75C20-20F-DBP 1-1/4-11-1/2 NPTF - - 4.40 4.75 N/A
1-1/2 75C24-24F 1-1/2-11-1/2 NPTF S75C24-24F 1-1/2-11-1/2 NPT 5.04 5.75 2.25
1-1/2 75C24-24F-DBP 1-1/2-11-1/2 NPTF - - 5.04 5.75 N/A
2 75C32-32F 2-11-1/2 NPT S75C32-32F 2-11-1/2 NPT 6.07 6.75 3.00
2 75C32-32F-DBP 2-11-1/2 NPT - - 6.07 6.75 3.00
2-1/2 75C40-40F 2-1/2-8 NPTF S75C40-40F 2-1/2-8 NPTF 5.29 8.00 3.50
3 75C48-48F 3-8 NPTF S75C48-48F 3-8 NPTF 5.84 8.50 4.25
75 Series Nipples
Part Part
Body Length Largest Wrench
Number Port End Number Port End
Size (in) Diameter Flats
Steel 316 Stainless Steel
3/4 75N12-12F 3/4-14 NPSF S75N12-12F 3/4-14 NPSF 3.27 1.75 1.56
3/4 75N12-12F-DBP 3/4-14 NPSF - - 3.27 1.75 N/A
1 75N16-16F 1-11-1/2 NPSF S75N16-16F 1-11-1/2 NPSF 4.17 2.25 2.00
1 75N16-16F-DBP 1-11-1/2 NPSF - - 4.17 2.25 N/A
1-1/4 75N20-20F 1-1/4-11-1/2 NPTF S75NC20-20F 1-1/4-11-1/2 NPT 5.36 2.62 2.38
1-1/4 75N20-20F-DBP 1-1/4-11-1/2 NPTF - - 5.36 2.62 N/A
1-1/2 75N24-24F 1-1/2-11-1/2 NPTF S75N24-24F 1-1/2-11-1/2 NPT 5.97 3.25 2.88
1-1/2 75N24-24F-DBP 1-1/2-11-1/2 NPTF - - 5.97 3.25 N/A
2 75N32-32F 2-11-1/2 NPT S75N32-32F 2-11-1/2 NPT 7.05 4.00 3.50
2 75N32-32F-DBP 2-11-1/2 NPT - - 7.05 4.00 N/A
2-1/2 75N40-40F 2-1/2-8 NPTF S75N40-40F 2-1/2-8 NPTF 7.46 5.00 3.50
3 75N48-48F 3-8 NPTF S75N48-48F 3-8 NPTF 8.26 6.00 4.25
Contact QCD for additional sizes and end configurations.
Optional Seal Materials and Features for Couplers and Nipples (add code to part number)
Code Description Part Number Example
suffix V Fluorocarbon seal material 75C12-12FV
suffix E Ethylene Propylene seal material (EPR) 75C12-12FE
suffix W Wrench flats on body (standard on 2-1/2” and larger, no code required) 75C12-12FW
suffix DBP “Fire Safe” BOP version (3/4”- 2” steel only, no alternate seal options) SB-75C12-12F-DBP
Contact QCD for availability and additional options.
To select proper seal materials, see Fluid Compatibility Chart or contact QCD.
Features:
• Flush face/Non-spill
• Push-to-connect
B Hydraulics
Applications include:
• Industrial hydraulic lines
• Off-shore drilling
Specifications
Body Size 1/4 3/8 x 1/41 3/8 3/8 x 1/22 1/2 3/4 1 1 x 1-1/43 2 x 1-1/44 2
Spillage (cc) .02 .02 .02 .02 .03 .06 .10 .10 5.25 5.25
Air Inclusion (cc) .01 .02 .02 .02 .03 .04 .06 .06 30.50 30.50
Performance
11355.00
1135.50
1135.50
2271.00
3406.50
3028.50
3785.00
2649.50
1892.50
7570.00
1514.00
113.60
265.00
227.10
340.70
757.00
302.80
378.50
151.40
189.30
227.10
340.70
378.50
302.80
757.00
265.00
113.60
151.40
189.30
37.85
22.71
34.07
75.70
30.28
11.36
26.50
18.93
15.14
37.85
75.70
7.57
3.79
B Hydraulics
100 6.90 100 6.90
90 6.21 90 6.21
80 5.52 80 5.52
70 4.83 70 4.83
60 4.14 60 4.14
50 3.45 50 3.45
(psi)
PRESSURE
40 2.76 40 2.76
(psi)
PRESSURE
PressureLOSS
LOSS(psi)
LOSS(psi)
PressureLOSS
4"
30 2.07 30 2.07
2"
4"
1/
Loss
Loss
Maximum Maximum
2"
8"
4"
1-
1.38
1/
20 1.38 20
Recommended
PRESSURE
Recommended
&
PRESSURE
1/
3/
3/
Loss(bar)
Loss
Flow Rate
Pressure
Pressure
Flow Rate
&
2"
1"
(bar)
1/
(bar)
(bar)
10 .69 10 .69
1-
9 .62 9 .62
8 .55 8 .55
7 .48 7 .48
6 .41 6 .41
5 .34 5 .34
4 .27 4 .27
3 .21 3 .21
2 .14 2 .14
1 .07 1 .07
10
40
70
80
100
300
600
700
1000
2000
3000
20
30
60
900
90
500
50
400
200
800
1
40
7
100
3
90
50
60
6
4
30
70
80
2
8
10
20
200
300
Flow
FLOWRate
RATE(GPM)
(gpm) Flow Rate (GPM)
FLOW RATE (gpm)
Hydraulic
HYDRAULIC Fluid Hydraulic
HYDRAULIC Fluid
FLUID
FLUID
Gallons per minute (gpm) in US gallons. Test Media MIL-H-6083 Hydraulic Fluid at 90°F ± 5°F (+32°C ± 1.5°C) sg .83
Ordering Guide
71-3 C 4 - 4 F
Options:
SL = Sleeve Lock
Seals:
Standard Seal = Nitrile
V = Fluorocarbon
E = Ethylene Propylene
M = MHO
End Fitting Type:
F* = Female NPTF
EF = Female SAE
RP = Female British Parallel BS2779
Autoclave cone & threaded fittings available
(consult QCD)
End Fitting Size:
4 = 1/4" 16 = 1"
6 = 3/8" 20 = 1-1/4"
8 = 1/2" 24 = 1-1/2"
12 = 3/4" 32 = 2"
Coupling Body Size:
4 = 1/4" 12 = 3/4"
6 = 3/8" 16 = 1"
8 = 1/2" 32 = 2"
Coupling Half:
C = Coupler
N = Nipple
Series:
71 = 1-1/2" & 2" Nipples Only
71-1 = 1-1/2" & 2" Couplers Only
71-3 = 1/4" thru 1-1/4" Both
Material:
Blank = Steel, zinc trivalent plating * For sizes up to 1" NPTF threads in steel.
S = 316 Stainless Steel For sizes up to 1" NPSF threads in stainless steel.
SH = High Pressure Stainless Steel For sizes over 1" NPT threads.
71 Series Couplers
1/4 71-3C4-4F 1/4 - 18 NPTF S71-3C4-4F SH71-3C4-4F 1/4 - 18 NPTF 1.96 1.19 0.94
1/4 71-3C4-4EF 7/16 - 20 UNF S71-3C4-4EF - 7/16 - 20 UNF 1.96 1.19 0.94
3/8 71-3C6-4F 1/4 - 18 NPTF - - - 2.36 1.56 1.19
3/8 71-3C6-6F 3/8 - 18 NPTF S71-3C6-6F SH71-3C6-6F 3/8 - 18 NPSF 2.36 1.56 1.19
3/8 71-3C6-6EF 9/16 - 18 UNF S71-3C6-6EF SH71-3C6-6EF 9/16 - 18 UNF 2.36 1.56 1.19
3/8 71-3C6-8F 1/2 - 14 NPTF S71-3C6-8F - 1/2 - 14 NPSF 2.57 1.56 1.19
1/2 71-3C8-8F 1/2 - 14 NPTF S71-3C8-8F SH71-3C8-8F 1/2 - 14 NPSF 2.77 1.88 1.50
1/2 71-3C8-8EF 7/8 - 14 UNF S71-3C8-8EF - 7/8 - 14 UNF 2.77 1.88 1.50
3/4 71-3C12-12F 3/4 - 14 NPTF S71-3C12-12F SH71-3C12-12F 3/4 - 14 NPSF 3.05 2.25 1.75
3/4 71-3C12-12EF 1-1/16 - 12 UNF S71-3C12-12EF - 1-1/16 - 12 UNF 3.05 2.25 1.75
1 71-3C16-16F 1 - 11-1/2 NPTF S71-3C16-16F SH71-3C16-16F 1 - 11-1/2 NPSF 3.32 2.63 2.00
1 71-3C16-16EF 1-5/16 - 12 UNF S71-3C16-16EF - 1-5/16 - 12 UNF 3.32 2.63 2.00
1 71-3C16-20F 1-1/4 - 11-1/2 NPT S71-3C16-20F - 1-1/4 - 11-1/2 NPT 3.32 2.63 2.00
1 71-3C16-20EF 1-5/8 - 12 UNF S71-3C16-20EF - 1-5/8 - 12 UNF 3.32 2.63 2.00
2 71-1C32-24F 1-1/2 - 11-1/2 NPT - - - 6.21 4.50 3.38
2 71-1C32-24EF 1-7/8 - 12 UNF - - - 6.21 4.50 3.38
2 71-1C32-32F 2 - 11-1/2 NPT - - - 6.21 4.50 3.38
2 71-1C32-32EF 2-1/2 - 12 UNF - - - 6.21 4.50 3.38
71 Series Nipples
B Hydraulics
1/4 71-3N4-4F 1/4 - 18 NPTF S71-3N4-4F SH71-3N4-4F 1/4 - 18 NPTF 1.84 0.89 0.81
1/4 71-3N4-4EF 7/16 - 20 UNF S71-3N4-4EF - 7/16 - 20 UNF 1.84 0.89 0.81
3/8 71-3N6-4F 1/4 - 18 NPTF - - - 1.84 1.18 1.00
3/8 71-3N6-6F 3/8 - 18 NPTF S71-3N6-6F SH71-3N6-6F 3/8 - 18 NPSF 2.32 1.18 1.00
3/8 71-3N6-6EF 9/16 - 18 UNF S71-3N6-6EF SH71-3N6-6EF 9/16 - 18 UNF 2.32 1.18 1.00
3/8 71-3N6-8F 1/2 - 14 NPTF - - - 2.57 1.65 1.25
1/2 71-3N8-8F 1/2 - 14 NPTF S71-3N8-8F SH71-3N8-8F 1/2 - 14 NPSF 2.38 1.65 1.50
1/2 71-3N8-8EF 7/8 - 14 UNF S71-3N8-8EF SH71-3N8-8EF 7/8 - 14 UNF 2.38 1.65 1.50
3/4 71-3N12-12F 3/4 - 14 NPTF S71-3N12-12F SH71-3N12-12F 3/4 - 14 NPSF 2.96 1.92 1.75
3/4 71-3N12-12EF 1-1/16 - 12 UNF S71-3N12-12EF - 1-1/16 - 12 UNF 2.96 1.92 1.75
1 71-3N16-16F 1 - 11-1/2 NPTF S71-3N16-16F SH71-3N16-16F 1 - 11-1/2 NPSF 3.23 2.09 1.88
1 71-3N16-16EF 1-5/16 - 12 UNF S71-3N16-16EF - 1-5/16 - 12 UNF 3.23 2.09 1.88
1 71-3N16-20F 1-1/4 - 11-1/2 NPT S71-3N16-20F - 1-1/4 - 11-1/2 NPT 3.23 2.20 1.88
1 71-3N16-20EF 1-5/8 - 12 UNF S71-3N16-20EF - 1-5/8 - 12 UNF 3.23 2.20 1.88
2 71N32-24F 1-1/2 - 11-1/2 NPT - - - 4.50 3.50 3.25
2 71N32-24EF 1-7/8 - 12 UNF - - - 4.50 3.50 3.25
2 71N32-32F 2 - 11-1/2 NPT - - - 4.50 3.50 3.25
Features:
• Manual threaded connection and actuation
• Hard, chrome alloy ball valves
• Polyurethane interface seal resists high pressure extrusion
• Threaded retainer provides a positive valve stop
B Hydraulics
Applications include:
• Hydraulic rams
• Portable hydraulic tools
• Crimping equipment
140
120
3/8"
Pressure Drop in PSID
100
80
1/4"
60
40
20
0
0 1 2 3 4 5 6 7 8 9
Flow in USGPM
B Hydraulics
1/4 3050-2 1/4-18 NPTF (Male) Ball 2.38 1.13 0.81 0.25
3/8 3050-3 3/8-18 NPTF (Male) Ball 2.38 1.38 1.00 0.49
3/8 3050-3-231 3/8-18 NPTF (Female) Ball 2.38 1.38 1.00 0.49
3000 Series Replacement O-Rings 3000 Series Dust Caps and Plugs
Body
Material Part Number Durometer
Size
1/4 Polyurethane 50001-114-0296 90
3/8 Polyurethane 50001-210-0296 90
Body Dust Cap Dust Plug Weight
Color/Material
Size (Nipple) (Coupler) (lbs.)
1/4 3009-2 Steel 3005-2 .02
3/8 3009-3 Steel 3005-3 .04
Features:
• Rated pressure up to 10,000 psi
• Manual sleeve operation
B Hydraulics
• Fluorocarbon seals
• Standard sleeve lock guards against accidental
disconnection
• Positive valve stop prevents flow checking
• Standard end configuration is female pipe thread
• Protective zinc plating with clear trivalent chromate finish
Applications:
Performance TC Series (3/8")
• Hydraulic jacking and house moving equipment
Test Fluid: Oil - 200 SUS
100 • Construction equipment
90 • Railway maintenance
80
70 Specifications
Pressure Drop in PSID
Coupler
Body
Part Number Thread Size Overall Length Largest Diameter Wrench Flats Weight (lbs.)
Size
3/8 TC-371 3/8-18 NPSF 2.48 1.25 0.94 0.43
Nipple
Body
Part Number Thread Size Overall Length Exposed Length Largest Diameter Wrench Flats Weight (lbs.)
Size
3/8 TC-372 3/8-18 NPSF 1.82 0.66 1.08 0.94 0.14
Features:
• 303 stainless steel body
• Rated pressure up to 10,000 psi and 17,000 psi intermittent
pressure
• Small diameter mating seal keeps separation forces to
B Hydraulics
a minimum, allowing easier threaded connection and
disconnection at pressures up to 5,000 psi
• Polyurethane seals to resist extrusion and abrasion
• Self locking threads guard against accidental disconnection
• Visual connection indicator – when fully coupled, sleeve edge
is flush with the end of the male thread
• Standard end configuration is female pipe thread
Specifications • Dust caps and plugs included
Body Size 1/4
Rated Pressure (psi) 10,000 Applications:
Rated Connect-Under-Pressure Capability (psi) 5,000 • Off shore equipment
Rated Flow (gpm) 3 • Hydraulic lines in corrosive environments
Temperature Range (Polyurethane seals) -30° to +180° F
Vacuum Test 20 in/Hg
Torque to connect at 1000 psi 47 in/lbs.
Coupler
Body
Part Number Thread Size Length Sleeve Hex Wrench Flat Weight (lbs.)
Size
1/4 1141-62 1/4-18 NPTF 2.75 1.00 0.88 0.40
Nipple
Body
Part Number Thread Size Length Wrench Flat Weight (lbs.)
Size
1/4 1141-63 1/4-18 NPTF 2.00 0.88 0.26
Features
• Steel nipples are case hardened for resistance to Brinelling
• Functionally interchanges with similar straight-through
design couplings
B Hydraulics
Applications:
• High pressure water
• Steam washers
• Carpet cleaners
Specifications
Body Rated Pressure (psi) Rated Pressure (psi) Rated Pressure (psi) Temperature Range
Rated Flow
Size Brass Coupler/Nipple Brass Coupler/Steel Nipple 303 SS Coupler/Nipple (standard seals)
1/8 2500 2600 4200 3
1/4 5200 5500 6700 6
3/8 2700 3500 5500 12
1/2 2200 2700 3000 12
-40º to +250º F
3/4 1700 2700 3000 28
1 1200 2000 1700 50
1-1/4 1700 – – 76
1-1/2 1400 – – 100
Performance ST Series (1/8", 1/4", 3/8", 1/2") ST Series (3/4", 1", 1-1/4")
Test Fluid: Oil - 150 SUS
Test Fluid: Oil - 150 SUS
12
5
10 1"
1/8" 4
Pressure Drop in PSID
8
3/4" 1-1/4"
3
6
3/8"
1/2"
2
4
1/4"
2 1
0 0
0 2 4 6 8 10 12 14 16 18 0 20 40 60 80 100
Flow in USGPM Flow in USGPM
B Hydraulics
1/8 BST-1 SST-1 1/8-27 NPTF 1.06 0.69 0.56 0.06 0.05
1/4 BST-2 SST-2 1/4-18 NPTF 1.54 0.94 0.81 0.17 0.15
3/8 BST-3 SST-3 3/8-18 NPTF 1.64 1.16 1.00 0.26 0.24
1/2 BST-4 SST-4 1/2-14 NPTF 1.98 1.30 1.13 0.40 0.37
3/4 BST-6 SST-6 3/4-14 NPTF 2.15 1.66 1.44 0.62 0.57
1 BST-8 SST-8 1-11 1/2 NPTF 2.43 2.02 1.75 0.99 0.93
1-1/4 BST-10 – 1 1/4-11 1/2 NPTF 2.44 2.51 2.00 1.38 –
1-1/2 BST-12 – 1 1/2-11 1/2 NPTF 2.88 3.00 2.50 2.43 –
303
Body Wrench
B Hydraulics
303
Body Brass Weight. Steel Weight. Weight. Largest Wrench
Stainless Length
Size Part No. (lbs.) Part No. (lbs.) (lbs.) Diameter Flats
Part No.
1/8 BST-N1M 0.02 ST-N1M 0.02 SST-N1M 0.02 1.04 0.51 0.44
1/4 BST-N2M 0.06 ST-N2M 0.05 SST-N2M 0.05 1.53 0.65 0.56
3/8 BST-N3M 0.08 ST-N3M 0.07 SST-N3M 0.08 1.69 0.79 0.69
1/2 BST-N4M 0.15 ST-N4M 0.13 SST-N4M 0.13 1.94 1.01 0.88
3/4 BST-N6M 0.23 ST-N6M 0.21 SST-N6M 0.22 2.19 1.23 1.06
1 BST-N8M 0.46 ST-N8M 0.43 SST-N8M 0.43 2.51 1.59 1.38
1-1/4 BST-N10M 0.96 – – – – 2.85 2.17 1.88
1-1/2 BST-N12M 1.46 – – – – 3.25 2.45 2.13
Features:
• Brass and stainless steel construction
• Nitrile seals
Applications include:
B Hydraulics
• Garden hoses
• Wash down systems
• Mobile water tank lines
Specifications
Body
Rated Pressure (psi) Rated Flow (gpm) Temperature Range (std seals)
Size
3/4 200 28 -40º to +250º F
Coupler
Nipple
Body Nipple
Port End Overall Length Exposed Length Weight (lbs.)
Size Part Number
3/4 1163-61 3/4-11 1/2 NH 1.25 0.50 0.08
Features:
• Steel material with electroless nickel plating
• Nitrile seals with PTFE back up ring
• No valving, unrestricted flow
B Hydraulics
Applications:
• Paper and pulp processing
• Refinery systems
• Testing systems
Specifications
Body Size 1/4 3/8 1/2
Rated Pressure (PSI) 15,000 15,000 10,000
Rated Flow (GPM) 3 6 12
Temperature Range (std seals) -40° to +250°F
Couplers
Nipples
Features:
• Rated pressure is 200 psi
• Valved and unvalved options. Valved couplers have silver
colored sleeves
B Hydraulics
• Brass material with standard silicone interface seals are
compatible with water and water glycol fluids. Valved
versions have a fluorocarbon seal on the poppet.
• Optional fluorocarbon seal for use with oil based media
• Short nipples can be installed recessed below the mold
Performance Moldmate Series (1/4", 3/8", 1/2") surface enabling more efficient storage and protecting the
Test Fluid: Water (Straight Coupler) nipple from damage
50
• Standard and Push-Lok hose barb ends are available in
45
1/4" Valved straight, 45 or 90 degree configurations
40
3/8" Valved
• Manual sleeve operation
35
Pressure Drop in PSID
30
• Extension nipples are offered in several lengths
1/4" Non-valved
25
20
Applications:
3/8" Non-valved
15 • Mold coolant lines
1/2" Non-valved
10 • Die casting equipment
5
0
0 2 4 6 8 10 12 14 16 18
Special Order Information:
Flow in USGPM Standard seal material is Silicone and is compatible with
water and water glycol fluids commonly used in heat transfer
Guidelines for Selection and Use: systems. Fluorocarbon seals are available for use with oil-
Non-valved couplers provide maximum flow for efficient based media. To specify a Fluorocarbon seal, add the suffix “Y”
cooling. Valved couplers shut off automatically when to the standard moldmate part number, thus: PC206Y.
disconnected. Valved couplers can be used with either valved
or non-valved nipples. A valved nipple, however, must be used
with a valved coupler.
Moldmate couplings are rated for 200 psi max pressure. Most
thermoplastic and thermoset heat transfer systems have pumps
which provide relatively high flow rates at low pressures. Water Specifications
and water glycol systems usually have capacities ranging Body Size 1/4 3/8 1/2
from 10 to 40 gpm with most from 10 to 15 gpm. Normal medial
opening pressures are 20 to 60 psi for these systems. Heat Rated Pressure (psi) 200
transfer systems using oil generally operate from 10 to 30 psi. Rated Flow (gpm) 3 6 12
However, their flow rates are usually much higher, requiring
the total volume of oil to be circulated at least once per minute.
The number of hose connections in a single mold system results Material Temperature Range
in a cumulative pressure drop. Please note the Pressure Drop Standard Silicone seal -20° to +400° F
vs. Flow Rate chart provided, to select the appropriate size.
*Optional Fluorocarbon seal -15° to +400° F
Temperature is another important consideration. Parker
Moldmate couplings with the standard silicone seal have a * For use with oil based media only
temperature capability of -90° to +400°F. Rapid deterioration
of the seal and leakage may result if used beyond these limits.
Couplers - Straight
Non-Valved Valved
1/4 PC204 0.10 PC204AV 0.10 1/4 1.87 0.63 2.67 0.71 0.63
1/4 PC204-BP* 0.10 PC204AV-BP 0.10 1/4 1.89 0.63 2.52 0.71 0.63
1/4 PC205 0.09 PC205AV 0.10 5/16 1.87 0.63 2.67 0.71 0.63
1/4 PC206 0.09 PC206AV 0.10 3/8 1.87 0.63 2.67 0.71 0.63
1/4 PC206-BP* 0.11 PC206AV-BP 0.13 3/8 2.04 0.63 2.70 0.71 0.63
3/8 PC306 0.24 PC306V 0.27 3/8 3.01 0.96 3.17 1.01 0.88
3/8 PC306-BP* 0.26 PC306V-BP 0.29 3/8 3.15 0.96 3.31 1.01 0.88
3/8 PC308 0.25 PC308V 0.28 1/2 3.15 0.96 3.17 1.01 0.88
3/8 PC308-BP* 0.25 PC308V-BP 0.03 1/2 3.27 0.96 3.43 1.01 0.88
1/2 PC504 0.46 NA – 1/2 3.55 1.30 –
1/2 PC504-BP* 0.50 NA – 1/2 3.68 1.21 –
1/2 PC506 0.48 NA – 3/4 3.80 1.21 –
1/2 PC506-BP* 0.52 NA – 3/4 3.80 1.21 –
NA = Not Available
Couplers - 45 Degree
* Suffix BP in part number denotes Push-Lok hose barb. Without suffix denotes standard hose barb.
Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps.
Valved Couplers can be used with either non-valved or valved nipples.
Couplers - 90 Degree
Body Part No. Brass Weight Part No. Brass Weight Hose Overall Wrench Largest Overall Wrench Largest
Size Non-Valved (lb.) Valved (silver sleeve) (lb.) I.D. Length Flats Diameter Length Flats Diameter
B Hydraulics
Non-Valved Valved
1/4 PC214 0.13 PC214AV 0.14 1/4 1.78 0.56 0.71 1.98 0.63 0.71
1/4 PC214-BP* 0.14 PC214AV-BP 0.14 1/4 1.78 0.56 0.71 1.98 0.63 0.71
1/4 PC215 0.13 PC215AV 0.14 5/16 1.78 0.56 0.71 1.98 0.63 0.71
1/4 PC216 0.14 PC216AV 0.15 3/8 1.78 0.56 0.71 1.98 0.63 0.71
1/4 PC216-BP* 0.16 PC216AV-BP 0.17 3/8 1.80 0.56 0.71 2.00 0.63 0.71
3/8 PC316 0.31 PC316V 0.31 3/8 2.78 0.88 0.96 2.78 0.88 0.96
3/8 PC316-BP* 0.37 PC316V-BP 0.37 3/8 2.78 0.88 0.96 2.78 0.88 0.96
3/8 PC318 0.33 PC318V 0.35 1/2 2.78 0.88 0.96 2.78 0.88 0.96
3/8 PC318-BP* 0.37 PC318V-BP 0.39 1/2 2.80 0.88 0.96 2.80 0.88 0.96
1/2 PC514 0.79 NA – 1/2 3.50 1.12 1.21 –
1/2 PC514-BP* 0.83 NA – 1/2 3.50 1.12 1.21 –
1/2 PC516 0.80 NA – 3/4 3.50 1.12 1.21 –
1/2 PC516-BP* 0.84 NA – 3/4 3.50 1.12 1.21 –
* Suffix BP in part number denotes Push-Lok hose barb. Without suffix denotes standard hose barb.
Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps.
Valved Couplers can be used with either non-valved or valved nipples.
Body Body
B Hydraulics
Body Body
Part Number Material Part Number Material
Size Size
1/4 P200-9A * Silicone 1/4 P200-9AY * Fluorocarbon
3/8 P300-9A * Silicone 3/8 P300-9AY * Fluorocarbon
1/2 P500-9A * Silicone 1/2 P500-9AY * Fluorocarbon
Weight Weight
Body Part No. Part No. Thread Overall Exposed Wrench Largest
(lb.) (lb.)
Size Brass Steel Size Length Length** Flats Diameter
Brass Steel
1/4 BPN251F 0.02 PN251F 0.02 1/8-27 NPTF 0.97 0.58 0.50 0.58
B Hydraulics
1/4 BPN252F 0.05 PN252F 0.04 1/4-18 NPTF 1.28 0.89 0.63 0.72
1/4 BPN253F 0.08 PN253F 0.08 3/8-18 NPTF 1.41 1.02 0.75 0.87
3/8 BPN352F 0.05 PN352F 0.05 1/4-18 NPTF 1.48 0.88 0.63 0.72
3/8 BPN353F 0.07 PN353F 0.06 3/8-18 NPTF 1.58 0.98 0.75 0.87
Valved Nipple
Features:
• Rated pressure is 250 psi
• Double shut-off valving
• Fluorocarbon seals
• Standard end configurations are female and male pipe thread
B Hydraulics
Applications:
• Dental equipment
• Lubrication lines
• Fluid transfer
• Coolant lines
8
Locking Device (balls) 5
6 Rated Flow (gpm) 0.8
1/8"
Temperature Range -15°F to +400°F
4
0 How To Order
0 0.2 0.4 0.6 0.8 1 1.2
Flow in USGPM DM - 12 1 - 4 FP
1= Valved Coupler
2= Valved Nipple
DM Series
* This dimension represents the portion that is exposed when a nipple is inserted into a Parker DM Series coupler.
* This dimension represents the portion that is exposed when a nipple is inserted into a Parker DM Series coupler.
B Hydraulics
corrosion situations, or other high wear and tear situations
such as dragging the product along the ground. Please see the No suffix is required when ordering products with the standard Nitrile
seals. When specifying an optional seal, refer to the following chart to
Fluid Compatibility Chart at the end of the catalog for a guide in
determine the appropriate suffix.
selecting material for various media. It is always recommended
that the Quick Coupling Division be contacted with any questions Coupling Ethylene Fluoro- Perfluoro-
Neoprene
concerning specific product application needs. Series Propylene carbon elastomer
60 Series W Y Z ***
Typically, a prefix or suffix is added to the base part number 6600 Series W Y Z ***
to specify a non-standard O-ring seal, or special option such SM Series E5 E4 E12 ***
as a sleeve lock. The Optional Seals Suffix chart illustrates
HP Series E5 E4 E12 ***
the designations.
4000 Series W Y Z N/A
4200 Series W Y Z N/A
NS Series E5 E4 N/A ***
FF Series E5 E4 N/A ***
Std. is E49
FH Series E5 E4 N/A ***
FS Series E5 STD E12 ***
6100 Series W Y Z N/A
5000 Series W Y Z N/A
8200 Series W Y Z N/A
9200 Series W Y Z N/A
3000 Series Available with Polyurethane only (no suffix needed)
TC Series Available with Fluorocarbon only (no suffix needed)
1141 Series Available with Polyurethane only (no suffix needed)
ST Series W Y Z
Water Service Available with Nitrile only
HO Series E5 E4 E12 N/A
Moldmate
Series N/A Y** N/A N/A
Std. is Silicone
** Fluorocarbon seal available for use only with oil based media, not
water glycol.
Description
These popular Quick Coupling Key Chains are constructed of
anodized aluminum and are available in an array of colors.
The original design, nickel plated version can be ordered as
well.
KEY-BK Black
KEY-BU Blue
KEY-GR Green
KEY-RD Red
KEY-CL Clear
KEY-NI Old style nickel plated