MANUAL FOR
am Olen dS
LOAD
CALCULATIONS
Bs
e
Canoe Ch
LECTURE SERIES ON WIND + EARTHQUAKE ENGINEERING
(BASED ON NSCP 2015): LOADED‘OUTCOME: Understanding & Computing STRUCTURE PERIOD
USING METHOD A, DESIGN BASE SHEAR, and SIMPLIFIED
DESIGN BASE SHEAR per Section 208 of NSCP 2015
Design Base Shear Section 208.5.2.1
Find the design base shear for a 5-story steel special moment-resisting frame building
shown below, given the following informatica:
Z=04
Seismic source type = B
Distance to seismic source = 5 km
Soil profile type = 5
a1
R=85
TT
[|
[|
LI
Wa7aM kn Ott
18.30 myCalculations and Discussion Code Reference
In solving this example, the following steps are followed:
L.Determine the structure period, T
2.Determine the seismic coefficients C, and C,
3.Determine base shear, V
Calculations and Discussion Code Reference
(Section 208.5.2.2)
1, Determine the structure period. p22US
where:
Method A to be used, G for steel moment resisting frames | G = (0853 for eel moments
is 0.0853, resisting frames.
C= 0.0731 for reinforced
1 Catg*= 088531839) = (€9.208-12) |" concrete mamentrsising
M55 as ‘ames. and eecemtrically
braced frames
~ 8.0488 forall other
buildingsors ihlagronnu gee ina
Cade Reference
Calculations and Discussion
(Table 208-$ & 208-6)
2, Determine the seismic coefficients C, and C,; nae
Table 208-5 Near-Soarce Foto Na
Find N,, and N, from Tables 208-5 and 208-6, ‘Seles ‘Chsest Distance Te
7 Source Seine Source!
respectively, knowing that the seismic source type | “Type _23km |= 5 ken co
is B and the distance 5.0 km. a
c to 1] 16
No= 10
Calculations and Discussion Code Reference
(abe 20827 & 208-8)
2, Determine the seismic coefficients C, and C.: PHT ccmune
From Table 208-7, for soil profile type S- and Z= 0.4 sea sna
C,=040N, —
ce
From Table 208-8, for soil profile type Sand Z = 0.4 =
Ca= 0.56N, "pum,
‘Sara aa
we |e aes |
=| ae} ae
See Se
ers Fab
tantra lie
ops oat epee oem
cmap2. Determine the seismic coefficients C, and C.:
Therefore:
ae (Fable 208.7 & 208.8
Cy 0.56(1.2) = 0.672 petit
AC ig one ong gee
Calculations and Discussion Code Reference
3. Determine base shear.
The total base shear in a given directions determined from:
Cl
= S219 57.232 762 KN (0.208-8)
P22143. Determine base shear,
‘However, the code indicates that the total design base shear shall not exceed
= 2SROAKO 5 959 = 8508 KN (2.208-99
yn 2at
“TR 85 p22
w
3. Determine base shear.
Another requirement is that the total base shear shall not be less than:
- - - (€9.208-10)
V=O011C 0 =O.11 x 0.40 x 1.0 x 7,232 = 318.2 KN p22Calculations and Discussion Code Reference
3. Determine base shear.
In Zone-4, total base shear also shall not be less than:
validly OB KOAKL2XLO, 9 959 2 3967 AN (6208-11)
R BS aad
3. Determine base shear,
(Section 208:52.0
In this example, design base shear is controlled by Eg.208-8: | p.2.214
Therefore: V=762KN EE
Bq 20e9 -W=n30 KN.
iq 208-10-V~31R2 KN
[Bg 208- 11: W= 226.7 RNUI MP!
(Giection ORLA
\p2-20?
Commentary:
‘The near source factor N, used to determine
C, need not execed 1.1 if the conditions of
‘Sec. 208.4.4.3 are met
Guide es the Use of Section 208
Earthquake Loads of NSCP 2015