Professional Documents
Culture Documents
3
1.1 Introduction of cutter master V6.x’s functions..............................3
1.2. How to distinguish the original Cutter Master V6.x...............................5
1.3 Shortcut table of menu...................................................................5
2. The ABC of Cutter Master...............................................................................11
2.1. System installation.................................................................................11
2.2. How to log in Cutter Master V6.x.........................................................15
2.3.Settings of layout....................................................................................15
2.4 how to input the characters....................................................................16
2.5 character attribute...................................................................................16
2.6 the usage of graphical library......................................................16
2.7 Operations of graphics...........................................................................17
2.8 Cutters output...............................................................................17
3. Attribute of character and layout.....................................................................18
3.1 Input of characters........................................................................18
3.2 Attribute of characters............................................................................20
3.3 Operation of typeset...............................................................................24
4. Graphic processing...........................................................................................34
4.1 line................................................................................................34
4.2 rectangle..................................................................................................34
4.3 circle.......................................................................................................35
4.4 polyline/polygon..........................................................................35
4.5 Bezier curve............................................................................................35
4.6 settings of right polygon/right polygon..................................................36
4.7 additional rectangle................................................................................36
4.9 form(TABLE).........................................................................................36
5. Deformation processing...................................................................................38
5.1 general deformation................................................................................38
5.2 artistic deformation.................................................................................40
5.3 clip................................................................................................41
5.4 Cutting..........................................................................................42
5.5. Thickening and thinning of lines.................................................44
6. Graphical library.....................................................................................46
6.1 Operation of graphical library......................................................46
6.2 Management of graphical library...........................................................47
7. Editing of node.................................................................................................48
7.1 logging in the editing of node................................................................48
7.2 Introduction of toolbar............................................................................49
7.3 Operational instructions of toolbar........................................................50
8. Selecting of colors and using of pallette..........................................................52
8.1 Selecting of colors........................................................................52
8.2 Setting of background..................................................................52
9. Scanning of images and sketching of curves...................................................53
9.1 Scanning of images................................................................................53
9.2 Reading of images..................................................................................54
9.3 Sketching of images...............................................................................54
9.4 Sketching of screen images....................................................................55
9.5 Vectorizing bar (grayscale vectorization).............................................55
1
10. Output.............................................................................................................56
10.1 Output of cutters...........................................................................56
10.2 Off-line output /multiple output...................................................59
10.3 Print...............................................................................................60
11 Frequently Asked Questions...........................................................................61
2
1. General
3
This system can provide the standardized interfaces for other Chinese
typesetting software and graphic processing software such as Word, WPS,
Photoshop, CoreIDRAW etc so that the Cutter Master can much more
compatible with others software.
The point editing is easy for using.
This software has advanced images editing function.
Zoom in/out
The users can display the output images in any scales and printout in actual
scale.
Off-line plotting
Some homemade plotting machines haven’t buffers so that the computers are
occupied as plotting, this new software has solved this problems.
Perfect output functions:
This system has been used for color preliminary, specified color output, zoom
output, sorting output, mirror output, rotating output, off-line output, multiple
output etc, and it is can also be connected to any plotting machines.
Multiple languages:
The software of Cutter Master V6.x can support the input of characters of the
minority nationality such as Korean character and Russian character, we also
provide the input of Mongolian character, Uygur character and Tibetan
character in the subsequent versions.
The functions provided by Cutter Master and some traditional tools are easier
for operation, how to effectively combine these functions to improve the work
efficiency is what the users must continuously grasp and accumulate their
experience to complete.
March, 2000
4
1.2. How to distinguish the original Cutter Master
V6.x
Firstly thanks for purchase the Cutter Master V6.x, and congratulate on your
becoming one of the users of Cutter Master. You can obtain the perfect
technical service.
If you order the Cutter Master for the first time, please inspect the followings:
1. One operation instructions of Cutter Master V6.x
2. One operation instructions of graphical library of Cutter Master V6.x
3. One softLock .
4. One disk.
5. One guaranty of Cutter Master V6.x.
5
Delete: delete the selected images or characters, the shortcut is Del
Multiple copies: one-off replicated the selected contents to as much as possible,
the shortcut key is F7 (P35)
Cards copies: one-off replicated the selected contents to as much as possible, the
shortcut key is Shift+F7 (P35)
Cutter Master
6
Align top: aligning several objects at the top side, the shortcut key is Ctrl+↑
Center horizontal: aligning several objects at the horizontal central line, the
shortcut key is Ctrl+End
Center vertical: aligning several objects at the vertical central line, the shortcut
key is Ctrl+PgDn
Align center: aligning several objects at the center position, the shortcut key is
Ctrl+5
Left/right uniform spacing: adjust the horizontal equidistance of several objects
Top/bottom uniform spacing: adjust the vertical equidistance of several objects
Alignment operations of layout:
Align left: moving several objects to the utmost left side of the layout
Align right: moving several objects to the utmost right side of the layout
Align bottom: moving several objects to the utmost bottom side of the layout
Align top: moving several objects to the utmost top side of the layout
Center horizontal: aligning Text Block at the horizontal central position of the
layout
Center vertical: aligning Text Block at the vertical central position of the layout
Align center: aligning the center of Text Block with the center of layout
Center layout: array the Text Block to the middle of layout
Layout of Text Blocks: (P30)
Forward landscape: the characters can be adopted horizontal mode from left to
right
Backward landscape: the characters can be adopted horizontal mode from right
to left
Forward portrait: the characters can be adopted vertical mode from top to
bottom
Backward portrait: the characters can be adopted vertical mode from bottom to
top
Vaulted typeset: the characters can be arrayed along vaulted line
Typeset along curve: the characters can be arrayed along a curve
Arced typeset: the characters can be arrayed along a specified arc line
Align left of characters: aligning the characters at left side
Full of characters: the whole screen can be filled with Text Blocks
Layout of characters:
Line head alignment: automatic indent (see page 38)
Canceling of line head alignment: cancel the automatic indent (see page 38)
Automatic uniform spacing: you can set the uniform spacing and inhibit array
mode of Text Block
Punctuation inhibited mode: the punctuation can’t be placed at the head of lines
Up-turn: turn one or more blocks to the front of the other blocks (see page 39).
Down-turn: turn one or more blocks to the behind of the other blocks (see page
39)
Cutter Master
5. Graphics
Line: you can draw a line on the screen (see page 41)
Rectangle: you can draw a rectangle on the screen (see page 41)
7
Circle: you can draw a circle on the screen (see page 41)
Others:
Polyline: you can draw lines of different points on the screen (see page 42)
Polygon: you can draw a polygon on the screen (see page 42)
Bezier curve: you can draw a Bezier curve on the screen (see page 42)
Regular polygon: you can draw a regular polygon on the screen (see page 42)
Regular polygon settings: you can modify the parameters of regular polygon
(see page 42)
Additional rectangle: you can add a rectangle frame for selected graphics (see
page 42)
Form: you can draw a form (see page 42)
6. characters
Changing of font size: you can change the size and angle of characters (see page
25)
Normal font size: standard font size mode (see page 26)
Absolute font size: absolute size of characters (see page 26)
Absolute uniform font size: relative size of characters (see page 26)
English parameter settings: you can set the size and base line of English (see
page 38)
7. system menu
Layout setup: you can setup the size and color of layout.
Seizure:
Seize the aligning line (see page 40)
Seizure of boundary:
Seizure of background grid:
Help:
Help topic:
About Master98: the system version, copyright and hotline of Cutter Master
V6.x
Path settings: you can setup the file paths for the Cutter Master
Vectorizing configurations of graphics: the vecorization of graphics and you can
design the parameter.
Cutter Master
8. windows
New windows: you can open a new window
Cascade: decrease the window and arrange them in multiple layers
Tile: you can array all windows with tile method
Arrange icons: setup the window icons
Other windows: the users can switch different windows here
Cutter Master
8
1. menu bar
2. toolbox
3. attribute bar
4. character attribute bar
5. character editor
6. window toolbar
7. file toolbar
8. color palette
9. region-position list
10. status bar
Cutter Master
Some of these buttons are double functions, when the mouse is moved to button,
the message with black letters and yellow background will appear. If the mouse
is moved to the selection status button, message of “ select status, select all” will
be appeared. Press the left button of mouse is the left of the comma and the right
button is the right of the comma, in this case, press the right button of mouse is
for selecting all.
2. Character attribute bar
a. Character library types b. Font c. Font size d. Standard font size e. Uniform
font size f. Absolute font size g. Alignment of line head h. Canceling of
alignment of line head i. Chinese characters j. Korean characters
3.Window toolbars
a. Displayed and hidden toolbox b: displayed and hidden status bar c: displayed
and hidden color palette d. Displayed and hidden character editor e.
Displayed and hidden region-position list f. Displayed and hidden attribute
bar
9
Cutter Master
4. Color palette
a. Expanding color palette b. Color control bar
5. Status bar
Status description of mouse:
1. Select status (the cursor is used for display the status)
This status is used for selecting one or more blocks
2. character status (the cursor is used for “I” status)
This status is used for character entering or selecting status
3. the node editing status (the cursor is used for display the status)
This status is used for editing glyph block or changing the attribute of other
blocks
Description of various types of blocks
1. Text Block: there are only character contents in this Text Block
2. Graphical block: there are graphics of graphical library in Cutter Master in
this graphical block
3. Glyph block: this block is the combination of lines or contour line
4. Line block: this block is used for single line
5. Rectangle block: there is a rectangle or rounded rectangle in this block
6. Circle block: there is a circle or arc shape in this circle block
7. Deformation block: this is the artistic block of Cutter Master
8. Group block: it is composed by various types of blocks
Cutter Master
10
2. The ABC of Cutter Master
If you want to master the ABC of this software in a short time, then please to
directly read this chapter. Here we will introduce the ABC of this software such
as “system installation, how to login in cutter master V6.x, layout, how to input
character, layout of character, output of cutter, etc”.
According to what we prompted, you can operate step by step.
11
a. Here, you must agree to license protocol of software, press YES to
continueCutter Master
b. Set up the path of installation, and press Browse to select a directory. If you
have finished your selection, then you can press Next> button to continue.
12
c. Select types of installation as following:
c. Here, you can select the parts that you want to install, press [Next] button to
continue.
13
d. Here, you can create a name of file document at Windows Starting menu.
Press “Next(N) >” , then the program will start to install automatically.
14
2.2. How to log in Cutter Master V6.x
1. Click to “Start” button in the Windows95/98
2. Move the cursor to “master V6.X”
3. Click the left mouse button, and log in cutter master V6.X.
2.3.Settings of layout
1. You can move the mouse to “Pageset” under “system” menu, click the left
mouse button, the layout setup will be appear (or shortcut key is Ctrl+F10).
We can design the required shown layout as your own requirements, if you need
the length is 60cm, then you can setup the length of 600mm. If you need the
length is 1m, then you can setup its length of 1000mm
Width of instantaneous offset paper (mm) width of layout (mm)
450 430
600 580
900 880
2. If you need the fixed layout such as standard shown layout, A4 paper, A3
paper etc, then click the pulling-down arrow at the right side of layout types to
select what you want to.
3. If you want to setup the background color of layout, then you can click the
button of Background Color.
4. You can setup the alignment grids and their colors.
At this time we will see the configured layout
15
2.4 how to input the characters
1. Select the Character option at the Edit menu, (or click T button in toolbox),
the cursor turn to I status.
2. Click the left button of mouse at the position where need to input the
characters, the prompt cursor will flash on layout
3. Select the input methods: you can press the Ctrl key on the keyboard, the
input method can be changed for each pressing of Shift key.
4. We now describe the input method by the Text Block “cutter master”
16
2.7 Operations of graphics
1. Ellipse
Select the specified region of Ellipse option in “Draw” Menu, drag the left
button of mouse and then release it, the ellipse will appear on the layout.
2. Circle
Select Circle option in “Draw” Menu, click the left button of mouse on the
required position of layout, then the system will popup a dialog window,
You can add the x- radial parameter and y-radial parameter, and then press OK
button
3. Rectangle/ square
Select rectangle or square option in “Draw” Menu, drag the left button of mouse
on the required position of layout, then the rectangle or square will appear on
the layout
Cutter Master
17
3. Attribute of character and layout
We will introduce the input of characters and graphics and their own attributes,
and the layout knowledge about characters and graphics. It is important for your
using and understanding this software
2. Input the four characters of Cutter Master shown as figure F3-1 on layout,
the font, font size of the four characters is set to default attribute, there is a
red line on the top of Cutter Master, called the base-line for typesetting.
18
3.1.2 Input the characters by batch processing method
1. Select the button in toolbar, the system will pop up the dialog box of
Text Editor
2. Move the cursor to the input region, press the left button of mouse, the
cursor I will flash in the frame.
3. Select the input methods
4. Input the characters such as the characters of “Cutter Master”
5. After the characters have been input, the cursor turn to I status, blacken the
characters required to be called in the layout, and then press the Ctrl button,
double click the left button of mouse, then the input characters will be
shown on the layout.
Remarks:
You can greatly improve the input speed by batch processing method, so you
can use this method when you have a great deal of characters. Otherwise, we
have provided a standard port of Windows for batch processing method, that is,
you can input the characters in the other software (such as Notepad or Wordpad
of Windows). Blacken the whole page of characters and select copy mode, and
then paste these contents to batch characters editor of Cutter Master. Thus the
whole characters will be called into the Cutter Master system or directly called
to the layout of Cutter Master, or directly called into Cutter Master system by
the File Paste option in File of Cutter Master.
Cutter Master
19
3.2 Attribute of characters
After select characters block or part of characters, you can select Change Font
Size option (or with the shortcut key Ctrl+F, or click the right button of mouse
in the T of toolbox) in Characters menu. The system will popup a dialog
window, you can setup EnglishWin Font Characters Library, TimesNewRoamce
Font, 15.51mm height, and 15.51mm width as shown above
Ⅱ. The modification of characters attribute bar
After selected the Chinese block or part of characters, you can directly modify
the attribute of each item in the Character Attribute Bar of Windows
20
| types | Font | Size |
r
When one of the Text Block is selected, there will appear 8 black control points,
you can drag the control points at the four corners, then you can directly change
the size of the whole characters block
Ⅳ). The using of Absolute font and Absolute Uniform font(only for Chinese
Fonts)
For the different fonts, there will be error between the output characters size and
real input value, if you want to reduce the error, we here provide two styles:
a. Absolute Uniform font size
For coordinating the overall beauty of Chinese, We can draw the longest side
(height or width) to required width, and then the other side can multiply its
drawing proportion, you can only press the button in the toolbar.
b. Absolute font size
Draw the each side of a character to required length, you can use the button in
toolbar.
We don't commend you in real operations, otherwise the beauty of characters
will be affected
21
cursor to the word “Master”, release the left button of mouse, the two words
of “Cutter” are blackened and selected as shown
When the cursor is on the I status, the users can adjust the word gap with Space
key or Backspace key, and the shortcut key Ctrl+F, the system will pop up a
dialog window, you can directly input values to change the word gap. Here we
setup the word gap as 20 (the unit of word gap is mm), at this time, the system
can automatic select and adjust the corresponding characters
The Cutter Master provides the easier method for adjusting the word gap, you
can select one Text Block in Select Status, then there will appear a red base line.
You can only adjust the distance of base line, select Text Block Typesetting, Fill
Line in Typeset menu, and then you can adjust the word gap as shown below:
22
3.2.3 the rotary and slope of characters
Select the Change Font Size option in Character menu (or use the shortcut key
Ctrl+F), the system will popup a dialog window shown as below, you can setup
the accurate angles of slope or rotary.
Note: (1). The final results of sloping and rotary of characters or Text Block is
different, for the Text Block, the slope and rotary is the whole Text Block.
(2). The operations of slope and rotary of Text Block (see the 1st section of 5th
chapter for the rotary part)
23
3.3 Operation of typeset
We will introduce the align operations of characters, layout of characters block,
automatic uniform spacing of character typeset, uniform spacing settings of
Text Block, Punctuation inhibiting mode, up-turn and down-turn etc, you can
typeset your characters much more beautiful by using these functions
24
The results are shown
as left
Remarks:
This results are
different from the later
arced typeset.
Attribute adjustment
Press the attribute button in Window Toolbar, or press Alt until popup attribute
toolbar after double click the left button of mouse in Text Block
Consist of:
25
Center alignment of the characters’ line
Backward landscape:
26
(2). Arced typeset
| 1-7 | 8 | 9 | 10 |
Consist of
1-7 typeset along the same arc line 8. Typeset angle of initial arc
9 typeset angle of end arc 10. The length of redial
Press Enter after the adjustment is over
(3). Typeset along curves
Operation instructions: we also
take the Cutter Master as an
example:
Input the four words of Cutter
Master, click the right button of
mouse and go back to select
status, select this Text Block.
Select the Typeset Along Curves in Layout menu, the results are shown as
27
following:
28
3.3.2 alignment operations
1. The operations such as align left, align right, align bottom, align top of
various blocks are identical.
We take the align left of Text Block and graphics block for examples,
(1). First we input the Text Block or
graphic block into the layout, and then
select the block that require to be aligned
left shown as right figure.
Remarks:
If you adopt selection of box dragging, you can select several objects at the
same times, press Shift key until move the cursor to other objects after selected
an object, click the left button of mouse and you can select the second object
continuously. Thus you can select several objects by this method, you can only
move the mouse if you want to move.
29
3.3.4 Copy of characters and graphics
1. copy of characters and graphics
If you want to copy the characters or graphics, you can operate by the
followings:
First: select the target object, copy first in Edit option of menu (or use the
shortcut key Ctrl+C), and then paste (or use the shortcut key Ctrl+V)
Second: select the target object, press Ctrl button and move the mouse, the
system will automatically copy what you want
Remarks: the replicated objects can be pasted for unlimited times
2. multiple copies
You can adopt the method above if you want to copy an object for one time. If
you want to copy for more than one copy, you can adopt the second method,
that is the Multiple Copies in Edit of menu (or shortcut key F7), the system will
popup the following dialog window shown as figure F3-19:
You can select the horizontal or vertical, the horizontal space and vertical space
between objects and adopting copy of whole page.
Cutter Master
30
will popup dialog box.
Input various parameters, press the (replicate) button.
Note: the system can automatically calculate the required copies by pressing the
button of Copy Whole Page.
31
3.9. Chinese punctuation and symbols
The Cutter Master provides such a symbol input method because some of the
Chinese platform can’t provide the input of Chinese symbols.
Press the Word button on the right of screen, a dialog box of region-location list
will appear on the screen shown as right figure, there are some adjust buttons on
its top.
In the typing and typesetting status, you can firstly place the cursor at the end of
a word, and double click the left button of mouse on the required punctuation
and symbols, and then you can typeset the required punctuation and symbol in
the location where the cursor is placed.
3.10 horizontal /vertical uniform spacing
This function can automatically adjust the inter-space of several blocks. The
system can calculate the total length of several blocks, and then calculate the
inter-space according to the quantity of blocks
3.11 automatic uniform spacing and punctuation inhibiting
Ⅰ). Automatic uniform spacing
Select the Text Block and then click Automatic Uniform Spacing in Layout, you
can typeset the Text Block, the Cutter Master will automatically align the end of
each line.
Ⅱ). Punctuation inhibiting
The punctuation can’t be placed at the head of lines in special typesetting field
(punctuation inhibiting). You can select the Punctuation Inhibiting in Typeset,
and typeset a Text Block again, the Cutter Master will automatically carry out
the function of Punctuation inhibiting.
Cutter Master
3.12 Alignment of line head and cancel the alignment of line head
For the special requirements of typeset, we adopt the method as following:
Blacken the characters that require to be aligned, and select the command
Typeset→Character typeset→Alignment of line head or press the corresponding
button in the character attribute bars.
3.13 Re-typeset of Text Block
Select the required target Text Block, and there are a large black box and a red
base line near the Text Block, you can draw one end of the red base line and
then the Cutter Master will automatically re-typeset.
3.14 Settings of English parameters
(only for Chinese system)For coordinating the output proportion of English and
Chinese, this software can used for setup the English parameters. You can select
English Parameter Setting in Character, then the dialog box will display as the
left figure
32
The English base line is used for adjust the proportion of English and Chinese
base line, the font size proportion is the ratio of width and height of Chinese and
English.
3.15 the attribute of layout
Ⅰ). Zoom in/out of layout
Zoom in or zoom out the contents on the layout in order to look clearly, the
operational steps are as following:
Method1: select the Zoom in or Zoom out in Zoom option of Typeset, and then
take the mouse’s location as center to zoom the contents (or shortcut key of
zoom in is F2 and shortcut key of zoom out is F3)
Method2: press Shift key, and press the right button of mouse to draw box (the
contents that need to be zoomed in or zoomed out may be in the drawing-box)
And display the contents full screen.
Ⅱ). Full page
We can check the final results what we input on the whole page, its operations is
the same as zoom in and zoom out, the shortcut key is F4
Press Shift and press the right button of mouse, and then the system will display
the contents in full page.
Ⅲ). The whole graphic
This function can display all contents in and out the layout, its operations is the
same as zoom in and zoom out, the shortcut key is F4+A
If you have selected one or several blocks, then you can display it with the
maximum mode
3.16 up/down turn
With this function, you can setup the hierarchy of one block in layout, such as
you can place one block on the other or at the end of other block, and carry out
adjustment for this block
3.17. Other editing operations such as paste
1. Cancel (shortcut key is Ctrl+Z)
Select this function to go back to the last operation. This function can go back
more than ten steps. If you have opened several windows, it can only operate in
the current window.
2. Delete
Delete the selected characters or blocks
3. Copy
Cutter Master
This function can copy the selected characters or blocks to buffers (that is
memory these contents and different from the normal copy)
4. paste
This function can copy the contents in buffer
5. cut
This function is equal to Copy+Delete
3.18 Seizure of aligning line/boundary
Press the left button of mouse at the place of ruler, drag to layout and then a pair
of aligning lines will appear on the screen. If you drag it out of layout, then you
delete it
Press Z button when you move a block, and then you can seize the aligning line
33
Press X button when you move a block, and then you can seize the boundary of
layout
34
4. Graphic processing
We will introduce the strong manual drawing functions in Cutter Master
4.1 line
It is easier to draw a line. You can select line operation, press the left button of
mouse on the layout and drag. When you select line, you can directly adjust the
line at its ends with the mouse
4.2 rectangle
Method 1: you can directly drag a rectangle with a mouse. If you press Shift
when you drag, then you can drag a square
Method 2: when you have selected rectangle operation, you can select a mouse
at the original point. And then a window will appear shown as the right figure,
you can input accurate values in this window and press OK
35
4.3 circle
Method 1: you can directly drag a circle
with a mouse. If you press Shift when
you drag, then you can drag a regular
circle
Method 2: when you have selected
circle operation, you can select a mouse
at the original point. And then a
window will appear shown as the right figure, you can input accurate values in
this window and press OK
When you have selected this circle, you can double click this circle (enter into
node editing), then there will be red squares at this circle, you can drag this
circle to an arc, pie or bow shape.
4.4 polyline/polygon
The polygon is a closed contour, but the polyline is non-closed contour, and
their operation instructions are identical.
Select polyline command, and drag some lines with mouse continuously, press
the right button of mouse and then the work is over.
Note: the polygon will automatically close the contour
36
4.6 settings of right polygon/right polygon
When you have selected polygon, a window will appear shown as figure below:
The difference of an acute angle polygon and polygon is shown as above, you
can adjust the laterals of ploygon, the width can be adjusted as graphic of
double line
You can select polygon command after adjustment is over, and drag a polygon
in layout with mouse.
4.9 form(TABLE)
The window shown as right will appear after you select the form generating
command.
The width and height of each box can be separated with comma and the unit is
37
mm
The purpose of width of outside line and inside lines are as following:
38
5. Deformation processing
Ⅰ. Zoom
Zoom functions are used for zoom in or zoom out the input characters and
graphics according to the ratio.
Select the Zoom in the General Deformation of Deformation, the system will
popup a dialog box of Zoom in or out. The Horizontal and Vertical on layout
represent the height and width of current selected contents. Enter values in
Ratio, zoom out if the value is less than 1 and zoom in if the value is more than
1. When you select geometric proportion, the zoom will carry out horizontally
and vertically at the same ratio.
You can also directly draw the 8 small black squares at the selected block to
carry out zoom processing. The left-top, left-bottom, right-top, right-bottom will
be draw at the same ratio. The top, bottom, left and right are draw along single
direction.
Ⅱ. Rotary
There are two different methods of rotary, you can select the Rotary in General
Deformation of Deformation. The system cans popup a dialog box of Rotary
shown as right figure. Press OK after you entered the accurate values.
You can also place the mouse to Chinese Text Block or graphics status, click the
left button of mouse shown as right figure. Press one of the four corners with the
left button of mouse, The graphic will be rotated. The center blue point is the
control point (can be moved). At this time, you can press Ctrl to copy in rotation
39
method.
Ⅲ. Slope
The Cutter Master provide two different rotary methods, you can select the
Slope in General Deformation of Deformation. The system cans popup a dialog
box of Slope shown as right figure. Press OK after you entered the accurate
values.
You can also place the mouse in select status to select characters and graphics,
click the left button of mouse shown as figure F4-5. Press one of the four
laterals with the left button of mouse, The graphic will be sloped.
Cutter Master
Ⅳ. Mirror
Shift of mirror is used for changing the characters or graphics to the image with
the results that seen from mirror. You can take the horizontal or vertical line or
both the horizontal and vertical line as the mirror base line. The dialog box is
shown as right figure.
40
5.2 artistic deformation
The Cutter Master has provided the users with plenty of artistic deformation
resource, the users can carry out the artistic deformations for any Text Blocks.
The results is shown as following:
1. Firstly you must input the characters or graphics in the layout of Cutter
Master,
2. In the select status, the mouse can select the required characters and graphics
3. A dialog box will be displayed at the Artistic Deformation of Deformation.
4. Select what you want in result names or icons, and then press OK.
5. The detailed adjustment of various deformations can be modified in the node
editing status shown as the following figures. In this case there are two
circles, the outer circle is base circle and can’t be modified, the inner circle is
proportional circle and you can adjust it with the mouse as the mouse is in the
node editing status.
41
5.3 clip
Ⅰ. Merge
The merge function is that you can take out the common part of two graphics
and merge them as a whole graphic shown as figure F4-6:
The operational instructions are as following:
1. Firstly you must choose the required contents
2. And then select the Merge command in Clip of Deformation
Ⅱ. Cut
Operational instructions: the same as the Merge functions
Ⅲ. AND
Operational instructions: the same as the Merge functions
42
Ⅳ exclusive-OR
Operational instructions: the same as the Merge functions
5.4 Cutting
Ⅰ. Line cutting
We provide the users with three line cuttings. Cutting is just like that the users
are given a knife to cut the whole Text Block or graphic into several parts, the
cut parts can carry out the operations such as select, color and deformation
shown as the following figure:
43
Ⅱ. Contour cutting
This function is that you can cut the other contour with a specified contour.
Firstly, you must select two glyph blocks, and then carry out the command of
contour cutting
Ⅲ. Parallel cutting
The parallel cutting is described as following:
1). Select the Text Block of Cutter Master and circle it with frame
2). Select Parallel Cutting in Cutting of Deformation
3). You can carry out the cutting operation according to the provided parameters
in the windows such as angle, width of cutting line, the initial point of cutting
etc
44
Ⅳ. Radioactive cutting
Operational instructions: the same as above, the results are as following:
Ⅴ. Ring cutting
Operational instructions: the same as above
45
The processing of turnings:
When the angle of turning is very small, the following change will be appear
during thickening and thinning shown as right figures:
The length of l will be lengthened with the decreasing of α, you must adjust the
processing method of turnings for avoiding this case.
Rounded turnings:
You can replace the turning with arc if the angle of
turning has been less than Turning Threshold during
thickening and thinning shown as the right figures.
Cutter Master
Turnings maintenance
You can replace the turning with others if the
angle of turning has been less than Turning
Threshold during thickening and thinning
shown as the right figures.
Retain original state
Without any processing, the characters or graphics are keeping original state.
Crocheting of characters
The left figure adopts the crocheting processing but the right figure doesn’t.
Accuracy:
It is used for calculating, at special condition you can increase the accuracy.
46
6. Graphical library
1. The graphical library of Cutter Master V6.x includes five types such as
foreign graphical library, foreign characters library, system graphical library
1, system graphical library 2, system graphical library 3, and Chinese
traditional patterns. Move the cursor to the name of graphical library, click
the left button of mouse, the system will display the types of library. You can
select one of the five types of library.
2. Move the cursor to left and right arrows at the right side of Number item,
click the left button of mouse to select the numbers of graphics (see
graphical library manual), the selected graphic is displayed in black.
3. Move the cursor to required graphic and click the left button of mouse, move
the mouse to layout region, and then click the mouse at the location of
designing of layout, the required contents will be displayed in layout region
shown as the following figure
4. The size of graphical library can be customized. Click any black spot with
mouse to change the size of library after you have selected the library.
47
6.2 Management of graphical library
The users can save their customized graphics into the library of Cutter Master
with the management of graphical library. The users can use these graphics at
any time.
Input the saved filename (*.LIB) in New item, and press the new button. Then
there is a New Library on the left side. Select the New Library and click it with
mouse, there will be a frame by the New Library, thus you can modify the name
of graphical library.
Ⅲ. Append of graphics
1. Append graphics from the other libraries
Select a graphical type at the left, and select other graphics from the right
window, double click this graphic. And then this graphical library can be
appended to the left types.
2. Append the new graphic
Press the graphical library button, and select required library and type in the
library toolbar, press the button, thus the graphic in the working window can be
appended.r
48
7. Editing of node
We will introduce how to edit with the node. Every graphic, character and
vectored contour is composed by lots of nodes, so the users can obtain great
benefit if they can grasp the tool of node editing.
49
7.2 Introduction of toolbar
The user can see the toolbar of node-edit, this toolbar includes
various functions such as increasing of node, decreasing of node,
breaking of node, connecting of node etc, these functions is
shown as following:
50
7.3 Operational instructions of toolbar
1.The selecting of node
Click the node in select status and then this node can be selected. And you can
also draw frame in the select status of node, thus several nodes can be selected
altogether in the frame.
Note: press Shift key to select
2.The moving of node
The Cutter Master V6.x can adopt relative
simply method, you can only click one or more
selected nodes in node-edit status with mouse
and then move to the required location and
release
If two nodes of one line have been moved, then
the location of this line have been moved.
3. Appending of node
Double click the left button of mouse at the line required to append nodes, or
select one node on line, then you can append a node according to the node-edit
toolbar.
4. Decreasing of node
Select one or several nodes, press the button in toolbox, and then delete all
selected nodes.
Press Ctrl button and frame or click a node with the right button of mouse, and
then this node can be deleted
Otherwise, if you append two nodes on a line, you append a new line. At the
same time, if you delete two nodes on a line, you reduce this line
5. change the line into curve and change the curve into line (shortcut key is
space button)
The users usually meet these cases, that is, you need to change a line into curve
or change the line into curve. Firstly you must select one point on line or curve,
and then press Space button or the button in toolbox, thus the line can be
changed.
51
Others:
Press Shift+top/bottom/left/right keys after select several nodes, then these
nodes can be aligned
Press top/bottom/left/right keys after select several nodes, then these nodes can
be moved
Press Shift+moving of left button of mouse after select several nodes, then this
node and its fore-and-aft nodes can be draw into right angle.
52
8. Selecting of colors and using of pallette
The Cutter Master V6.x is color version, we will introduce how to color a Text
Block or graphical block and how to setup background colors.
2. Select the required colors in the background colors of window, and then
press OK button. (If the background need to be setup, you can setup size
and the color of background grids by the size of background grids). There
aren’t background grids if the size value is zero or less than zero.
53
9. Scanning of images and sketching of
curves
54
9.2 Reading of images
This function can call the other files saved and scanned by other software into
the Cutter Master system.
The detailed operation instructions are as following:
1). Select the Reading images command in Image of File menu, then the
following window will appear.
(2). Select the path of file
3). Enter your required files in filename, and then press Open button.
Note: we call the 512 box as grayscale that will be used in the sketching of
screen images.
3). You can select the commands in the window, and then carry out
vectorization processing shown as left figure.
4). The processing time will be different according to the
size of images, the results will be shown as following after
processed.
5). If you want to distinguish the results with the original
graphic, you can only zoom in what you want to see. If
you want to process the vectorized images, you can only
move and delete the original images.
55
9.4 Sketching of screen images
This function is useful for the modification and sketching of images. The
modification and sketching of images in the other graphics processing software
(such as Photoshop, PhotoStyler, ImagePal etc) is that you must firstly scan the
graphics and then saved (the graphics can be displayed fully on the screen). For
the Cutter Master system, you can select Sketching of Screen Images in Scan of
File menu, the screen will automatically upturn the graphics processing
software. You can draw a frame to frame what you want to sketch with the
mouse. The Cutter Master will automatically sketch the framed images and save
them into the layout of Cutter Master.
Note: if the image is a color or monochrome graphic, you can adjust one item of
grayscale in Images Vectorization window to determine the points, the value
range is 1-768, the less the values, the more the points.
We will automatically calculate the total bars according to the height of images
and the height of each bar. The commended height of each bar is about 5mm,
and the error of fitting is 1-5. Press the Bar Processing button, the grayscale
vectorization will be carry out automatically.
56
10. Output
Descriptions of icons:
Select: the mouse is at the status of selection
Settings of output region: select the output contents on the layout
Clear all settings in the output region: clear all settings in the output
region on the layout
Setup the output region: move the settings of the output region, and
select the output contents and then output.
Setup the unable output region: don’t output the settings of an output
region
Output of cutters: click the Output of Cutters after selected the output
region, the system will popup a dialog window.
Cutter Master
57
Ⅰ. Settings of output
The users must setup the output devices when they log in this dialog for the first
time, and also they must check the output devices before output, the output
devices consist of:
(1). Devices: the users can select the devices according to the type of plotting
machine, if there aren’t options in the pulling-down menu of plotting machine,
you must contact with dealer, or determine the languages accepted by plotting
machine are HPGL or DMPL, and then select the corresponding output options
2). Ports:
The settings of ports is very important, the plotting machine will be out of work
if the settings of ports aren’t correct. There are normally three ports such as
COM1, COM2 and LPT1, after all, you must ensure that your plotting machine
has been connected with the signal line of computers, and then determine your
ports. If you can’t determine, you can test them orderly.
There is File item in ports, it can be used to output the data for plotting machine
to a file. If you select this item, the system will prompt you entering the
filename as output
3). The width and height of instantaneous offset papers: consist of 45CM,
60CM, 90CM and 120CM. The real width usually less about 2-3CM for
retaining the roller’s width of plotting machine.
4). Velocity: you can setup the cutting velocity of plotting machine in software,
but some of the plotting machine can’t support the settings of velocity.
5). Cutter’s pressure: you can setup the pressure in software, but some of the
plotting machine can’t support the settings of velocity.
Cutter Master
6). Test: this button is mainly used for adjusting pressure, when you have setup
the pressure, a square will be output to plotting machine after you selected this
58
button. You can check the pressure and adjust as requirements.
7). Reset: a reset command will be send to plotting machine then the plotting
machine can reset to original status when you press this button
8). Output: when you press this button, the plotting machine start to cutting.
Ⅱ. plotting options:
1. save paper method
If this method has been selected, the plotting machine will automatically setup
the output from initial point. That is, if the Text Block is at the middle of layout,
but it must be plotted from the initial point for saving the offset paper.
2. output of specified color
If the full colors have been selected (there is a √ before the Full Color option),
all contents can be one-off output without the limiting of colors.
If you haven’t selected the full color, you can select the color in Output of
Colors, and then the plotting machine will output the corresponding colors after
you have selected Cutter option. If there isn’t this color, the plotting machine
will not output
3. Automatic paper feed
4. Character line: each character can be framed
5. Framed layout: the output layout can be framed.
6. Sorting: sort what you want to output
7. Off-line cutting: with the off-line cutting, the users can do the other works
after the plotting machine has started to work. At this time, the plotting
machine hasn’t occupied the computers. With this function, the users can
obtain high efficiency. The detailed description see the off-line cutting
8. Using of half-cutting
It likes the margin of stamps, a kind of cutting method that can made the
margin with virtual real mode. It mainly used for half a paper
9. Accuracy: the accuracy value is 1.0-9.0, less the value, the higher the
accuracy. Cutter Master
10. Zoom: the machine can output according to the zoom in or zoom out, the
value 1 represent the original size, 0.5 is 1/2 of original size, 2 is double size.
11. Paper feeding: when cutting is over, a little more paper need to be feed for
cutting
12. Mirror: the whole contents will be mirrored horizontally.
13. Rotary: the whole contents will be rotated in 90°
Ⅲ. Output parameters:
Drawing mode/compensation
There aren’t hardware compensation in home-made plotting machine, and adopt
compensation by software, the compensation value is setup in Compensation,
when you use the drawing pen, please select the drawing mode
Closing:
For some reasons, some plotting machine can’t close the initial and end point of
contour, thus we must adjust this value about 100.
59
Cascade of page: settings of interval between papers, the unit is mm
Pause: when you select off-line cutting, the output is not only one page. If you
select this item, the output will pause at interval and wait for command
Ratio adjustment: adjust the horizontal or vertical output ratio of plotting
machine according to requirements
Ⅳ. Settings of ports
This is the communication method between computers and output devices, these
settings can’t be changed except professors. You can press Recall Data to recall
the original value.
This item is used for cutting start without pause, automatically cut the whole
data
Start to cut, and pause after a work is over
Start to cut, and pause at interval
Pause the current cutting
Stop the current cutting
Stop the current cutting and clear the current cutting data
Add the cutting copies
Reduce the cutting copies
Select the cutting data that wasn’t deleted last time in hard disk
Delete all cutting data
60
10.3 Print
The results can be output by printers, we will introduce how to print
1. settings of printing
Here you can setup the type of printer, and paper size
2. selection of output
print boundary: print the outer frame of layout
print image: you can print lattice image (graphics block)
90rotation: print the layout with 90rotation
3. zoom
zoom according to layout
You can calculate the scale according to size of layout, paper, and spacing
zoom according to image
You can calculate the scale according to the real size of image, paper, and
spacing
custom
You can manually customize the printing ratio and fill at ratio position
4. Settings of copies
Copies
5. spacing
settings of margin on layout
61
11 Frequently Asked Questions
62
6). There are error on plotting machine, you can contact with the dealer
7). There are error on plotting software, you can install the system disk again
63
Select the required printer in printer list, you can select Install from Disk if there
are printer driver disk
Select the corresponding disk and installation program and go on the next step
The system will prompt the required ports for printer, usually you can select
LPT1
Setup the printer as fault printer
At this time turn on the printer, and select Recommend printing test page on the
operational interface
Click Complete button, the system finish the installation of printer
64