Professional Documents
Culture Documents
Unistrut: Application, Installation, Specification Guide
Unistrut: Application, Installation, Specification Guide
Unistrut: Application, Installation, Specification Guide
TM
®
Metal Framing
ELECTRICAL CONSTRUCTION
APPLICATION,
INSTALLATION,
SPECIFICATION
GUIDE
Metal Framing
INTRODUCTION
Lighting Supports
Fluorscent Fixture Applications . . . . . 4
High-bay Fixture Applications . . . . . . . 5
Mounting Options . . . . . . . . . . . . . . . . . . . . 5
Channel and Related Components . . . . 6
Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Florescent Fixture/Raceway Hangers . . 7
Finishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical Accessories . . . . . . . . . . . . . . 8-13
Technical Data . . . . . . . . . . . . . . . . . . . 14-18
Guide Specification . . . . . . . . . . . . . . . . . . 19
WALL-MOUNTED
CONDUIT SUPPORTS
Wall-mounted Unistrut channel and
pipe clamps work together to provide Note: All dimensions in parenthesis are
an ideal support system for this millimeters, unless otherwise indicated.
vertical conduit run.
3
TM
P1000
P3184
P2521-75
P2540
P2603
P3184
P1280W
Fixture attached to raceway by P2603 1/2" nipple assembly Conduit enters raceway by means of a P2521-75 end
at channel knockout. P1280W end cap, P3184 closure strip, connector. Open section of channel slot is closed by cut length
P2535 conduit connector, and P2855 raceway hanger of P3184 closure strip. Fixture is attached to and wired from
complete the assembly. For splicing channel into continuous P2540 wiring stud nut. P2855 raceway hanger supports
runs, use splice fitting P3922. raceway. For splicing together a continuous run, use splice
P2855 fitting P3922.
P2763
Plug-in
system
P2537
P1000
P2521-75
Conduit enters raceway by means of P2521-75 end
connector. P2763 duplex receptacle feeds plug-in type
fixture. P3184 closure strip covers open slot areas of
channel. P2855 raceway hanger supports raceway from
threaded rod. P2537 hanger supports fixture from raceway.
P3184
Conduit connects through knockout in fixture. Fixture is Conduit connects through knockout in fixture. Fixture is
supported by P1006-1420 spring nut and 1/4" round-head supported by HHCS series hex bolt and hex nut. Raceway is
machine screw. Assembly is supported by P2855 raceway supported by P2855 raceway hanger. To splice a continuous
hanger. run, use splice fitting P3922.
4
LIGHTING RACEWAY/SUPPORT SYSTEMS
HIGH-BAY FIXTURE RACEWAY APPLICATIONS
P3184 P2536 P1280W
P2535 Fixture attached to and
wired from raceway by
1/2" nipple assembly of P3184
P2855
P2855 desired length at channel Fixtures are connected
P1280W knockout. P1280W end to and wired from
cap, P3184 closure strip, P100 KO raceway by conduit
P2535 conduit connector, hanger P2536 or P2535.
and P2855 raceway hanger Raceway is supported by
P100 KO complete assembly. For P2855 raceway hanger.
splicing channels into P1280W endcaps and
continuous raceway runs, P3184 closure strip
use splice fitting P3922. complete the assembly.
H.I.D. Conduit connected to
knockout raceway through
mounted High-bay channel knockout.
system dual
P3184
mounted P2602 P1280W
P2763 system
P3184
P2521-75 P2761
P2855
M2250
Fixtures are supported by P2602 high
Fixtures, supported by P2855 raceway hangers and bay lamp hangers. Cover plate on P2761
M2250 swivel hangers, plug into receptacle mounted in outlet box provides access to receptacle
P2763 receptacle unit. P2855 hangers also support box. Raceway is supported and wired by
raceway. P2521-75 end connector joins conduit to top mounted P2535 conduit connectors.
raceway. P1280W end caps (not shown) and P3184 P1280W end caps and P3184 closure
closure strip complete assembly. P2855
strip complete assembly.
MOUNTING OPTIONS
A variety of clamps simplifies attachment to structural beams.
Other mounting options include concrete inserts, expansion anchors and powder-actuated fasteners.
5
TM
CHANNEL
UNISTRUT
HS T KO H3 DS
9/16" holes on 1 1/8" x 9/16" slots 7/8" knockouts 9/16" holes on 7/8" X 2 3/4" slots
1 7/8" centers on 2" centers on 6" centers 1 7/8" centers on 3 1/2" centers
8"
(203.2)
P3712P
Optional plastic filler to
prevent concrete seepage.
Wt. Wt. Wt.
Lgth Lbs/C Lgth Lbs/C Lgth Lbs/C
P 3249 3" 85 P 3257 32" 527 P 3264 9' 1741
P 3250 4" 100 P 3257A 36" 616 P 3265 10' 1947
P 3251 6" 130 P 3258 40" 661 P 3266 12' 2334 P3184 P P3184
P 3252 8" 159 P 3259 4' 786 P 3267 14' 2717 Material: GE Noryl® Material: Steel
P 3253 12" 227 P 3260 5' 1003 P 3268 16' 3116 Wt. 9.4 Lbs. / C Ft. Wt. 47 Lbs. / C Ft.
P 3254 16" 270 (14.0 kg/100 m) (69.9 kg/100 m)
P 3261 6' 1173 P 3269 18' 3530
P 3255 20" 357 P 3262 7' 1390 P 3270 20' 3882
P 3256 24" 399 P 3263 8' 1560 Standard length -10 feet.
6
NUTS/HANGERS
NUTS
Part Thread WT.
Part Thread WT. Part Thread WT. Number Size Lbs/C
Number Size Lbs/C Number Size Lbs/C
P3016-
P1006- P4006- 0632 #6 32 2
1420 1/4" 20 7 1420 1/4" 20 7 0832 #8 32 2
P1007 5/16" 18 6 P4007 5/16" 18 6 1024 #10 24 4
P1008 3/8" 16 10 P4008 3/8" 16 9 1420 1/4" 20 4
P1009 7/16" 14 9 P4009 7/16" 14 9
for P3300, P4000 & P5000
P1010 1/2" 13 12 P4010 1/2" 13 8 channels
Part Thread WT.
Number Size Lbs/C
P1012S 5/8" 11 21 P4012S 5/8" 11 11
P1023S 3/4" 10 21 P4023S 3/4" 10 11 P5506-
P1024S 7/8" 9 21 1420 1/4" 20 1
for P3300, P4000 P5507 5/16" 18 6
for P1000, P1100, P2000 & channels
P5508 3/8" 16 10
P3000 channels
P5509 7/16" 14 10
P5510 1/2" 13 12
for P5500 channel
RACEWAY HANGERS
A P2855
P2755 A Part “A” Weight/C
P2856
P2756 Number In mm Lbs kg
P2867
P2757 P2755 9/16 14.3 44 20
4 1⁄4" P2756 7/8 22.2 44 20 2 3⁄4"
(108.0) (69.9)
P2757 13/32 10.3 44 20
P2855 9/16 14.3 32 14.5
P2856 7/8 22.2 32 14.5
9 Design Load
Design Load P2857 13/32 10.3 32 14.5 ⁄32" (7.1)
120 Lbs. (.5 kN) 120 Lbs. (.5 kN)
9
⁄32" (7.1) Sq. Hole
Sq. Hole
Use with channels: P1001, P1101, Use with channels: P1000, P1100, P2000, P3000,
P2001, P5000 and P5500. P3300, P4000, P4001, P4100 and P4101.
Material: 14 gage (1.9) Material: 14 gage (1.9)
FINISHES
Pregalvanized channel is coated with zinc by hot-dipped process prior to roll forming of press operations. The zinc weight coating is
0.45 oz./side per square foot of material conforming to ASTM specification A-653.
Electro-galvanized parts, screws and nuts are coated with zinc electrolytically to commercial standards. (Federal Specification No. QQ-Z-325A.)
Hot-dipped galvanized material is coated with zinc after being roll formed or after all manufacturing operations are completed. The zinc weight
is 2 oz. per square foot of surface conforming to ASTM specifications Nos. A-123 and/or A-153.
Nuts, bolts and pipe clamps are electro-galvanized.
(Alternate finishes may be specified, such as pregalvanized finish and hot-dipped galvanized finish for various parts of the metal framing
system. Refer to Unistrut General Engineering Catalog #12 and supplementary bulletins for the availability and appropriateness of the finish for
various parts.)
7
TM
ELECTRICAL ACCESSORIES
UNISTRUT
CONDUIT HANGER CONNECTION FOR 1/2” CONDUIT CONDUIT HANGER CONNECTION FOR 3/4” CONDUIT
1
1
⁄4" X 5⁄8" Flat Head
⁄4" X 5⁄8" Flat Head P2536 Machine Screws and
P2535 7 Machine Screws and
⁄8" (22.2) Dia. P3016-1420 Nuts Included
P3016-1420 Nuts 1 3⁄32" (27.8) Dia.
Design Load Included
400 Lbs (1.3 kN) Design Load
200 Lbs (1.3 kN)
1 5⁄8"
4" (41.3) 5 1⁄8"
(101.6) (130.2)
Material: 12 gage (2.7) Wt./C 28 lbs. (12.7 kg) Material: 16 gage (1.5) Wt./C 36 lbs. (16.3 kg)
1 2 1⁄4"
6 1⁄4" ⁄4" X 5⁄8" Flat Head Machine (57.2)
(158.8) 3 Knockouts Screw and P3016-1420 Nut
7
⁄8" (22.2) Dia. Included
Material: 12 gage (2.7) Wt./C 35 lbs (15.9 kg) Material: 12 gage (2.7) Wt./C 27 lbs. (16.3 kg)
END CONNECTORS FOR 1/2” & 3/4” CONDUIT END CONNECTORS FOR 1/2” & 3/4” CONDUIT
P5500
P2521-50 A P5521-50 A
P2521-75 P5521-75
1
⁄4" X 5⁄8" Flat Head 1
Machine Screw and ⁄4" X 5⁄8" Flat Head
P3016-1420 Nut Machine Screw and
Included P3016-1420 Nut
2 1⁄16" Included
(52.4) 1 3⁄8"
(34.9)
Part Conduit Size A Weight/C Part Conduit Size A Weight/C
Number In Lbs kg For Unistrut channels Number In Lbs kg
P1000, P1100 & P2000.
P2521-50 1/2 27 12.2 Material: 12 gage (2.7) P5521-50 1/2 27 12.2
P2521-75 3/4 26 11.8 P5521-75 3/4 26 11.8 Material: 12 gage (2.7)
END CONNECTORS FOR 1/2” & 3/4” CONDUIT END CONNECTORS FOR 1” CONDUIT
Tapped for 1"
P5500
P5021-50 A Conduit Thread
P2521-100
P5021-75
1 P1000
⁄4" X 5⁄8" Flat Head
Machine Screw and
1
P3016-1420 Nut ⁄4" X 5⁄8" Flat Head
Included Machine Screw and
P3016-1420 Nut 2 1⁄16"
1 3⁄8"
(34.9) Included (52.4)
Part Conduit Size A Weight/C
Number In Lbs kg
P5021-50 1/2 31 14.1 Not UL-listed or CSA approved
P5021-75 3/4 30 13.6 Material: 12 gage (2.7) Material: 12 gage (2.7) Wt./C 24 lbs. (10.9 kg)
8
ELECTRICAL ACCESSORIES
END CONNECTOR FOR 1” CONDUIT END CONNECTOR FOR 1” CONDUIT
Tapped for 1" Tapped for 1"
Conduit Thread Conduit Thread
P5021-100 P5521-100
P5000 P5500
Material: 12 gage (2.7) Material: 12 gage (2.7)
Wt/C 28 Lbs (12.7 kg) Wt/C 24 Lbs (10.9 kg)
1
⁄4" X 5⁄8" Flat Head
1 5
⁄4" X ⁄8" Flat Head Machine Screw and
Machine Screw and P3016-1420 Nut
1 5⁄8"
P3016-1420 Nut Included (41.3)
1 5⁄8"
Included (41.3)
Not UL-listed or CSA approved Not UL-listed or CSA approved
P2540 Wiring
2"
Stud Nut 2" (50.8)
Flourescent Fixture
(50.8) Material: Sintered metal.
1 21⁄32" 4"
(42.1) (101.6) PART CONDUIT SIZE A WEIGHT/C
NUMBER In mm Lbs kg
Material: 12 gage (2.7) P2540 1-1/8 28.6 10 4.5
Wt./C 24 lbs (10.9 kg)
P2540 A 5/8 15.9 8 3.6
P2552
P3116-125 1 1⁄2" 1 1⁄2"
1
⁄4" x 20 Thd. (38.1) (38.1)
1 3⁄16"
(30.2)
9
TM
ELECTRICAL ACCESSORIES
UNISTRUT
SPLICE FITTINGS
Assembly Use “A” Clevis Back Plate Weight/C
Number With Number Clevis Nut
P3922 - P2869 14 gage (1.9) Channel In mm Number Number Lbs kg
P3926 P1000
A P3922 P1100 1 5/8 41.3 P2377 P2517 P2869 100 45.4
P2000
Threaded P3923 P3000 1 3/8 34.9 P3377 P2517 P2869 97 44.0
Plate Nut
P3924 P4000 13/16 20.6 P5377 P2517 P2869 80 36.3
3 5 P3925 P5500 1 5/8 41.3 P2377 P5517 P2869 103 46.7
6 ⁄4" 1
⁄4" X ⁄8" Flat Head Machine Screws
(171.5) and 4 Hole Splice Plate Nut Included P3926 P5000 1 5/8 41.3 P2377 P5017 P2869 106 48.1
IN-CHANNEL JOINERS
P2900 P2901 P2902 P2903
Wt./C 20 lbs (9.1 kg) Wt./C 35 lbs (15.9 kg) Wt./C 27 lbs (12.2 kg) Wt./C 45 lbs (20.4 kg)
P1000
BRACKETS
2" (50.8)
2"
P2513A- 2"
(50.8) P2513 - (50.8) P2542 - 13
⁄16"
P2516A P2516 1
⁄4"
P2546 (20.6)
1 A
⁄4" (6.4)
(6.4)
3
3 3⁄4" 3 ⁄4"
(95.3) (95.3)
6 1⁄4"
(158.8)
P1001
3
⁄8"
A (9.5)
A Part Std.
Part Std. Part Std. Number Lengths
Number Lengths Number Lengths
P2542 12"
P2513A 6" P2513 6" P2543 18"
P2514A 12" P2514 12" P2544 24"
P2515A 18" P2515 18" P2545 30"
P2516A 24" P2516 24" P2546 36"
10
ELECTRICAL ACCESSORIES
DUPLEX GROUNDED RECEPTACLE
P2553
P2557 Wire Connectors Oval Head
#6-32 X 1"
• 125 V, 15 amp receptacle, NEMA
configuration S-15R, cover plate.
• #6 screws, nuts and wire connectors
included. 6"
• Leads are 14 gage 105˚C plastic (152.4)
covered.
• Ground wire is green 16 gage. P3016-0632
P3184 Closure
RECEPTACLE BOX
P2761 7
⁄8" Knockout
1⁄4" x 5⁄8"
P2762 Part Weight/
Number Outlet Lbs kg
P2761 Single 88 39.9
P2762 Duplex 88 39.8
Includes Nuts
and Screws
P3016-1420
RECEPTACLE UNIT
P2763 NEMA
P2764 7
⁄8" Knockout 1⁄4" x 5⁄8" Part Weight/ Receptacle
P2765 Number Outlet Lbs kg Configuration
P2763 125V 108 49 5-15R
P2764 250V 108 49 6-15R
P2765 277V 108 49 7-15R
Includes Nuts
and Screws
P3016-1420
JUNCTION BOXES
P2810 P2812 P2814
Wt./C 135 lbs (61.2 kg) Wt./C 155 lbs (70.3 kg) Wt./C 195 lbs (88.5 kg)
P2811 P2813
Wt./C 155 lbs (70.3 kg)
Wt./C 175 lbs (79.4 kg)
11
TM
ELECTRICAL ACCESSORIES
UNISTRUT
Separator
Use with steel clamp and Everdur hardware. Order clamp separately. Material: Paraffin impregnated
Material: Dry process porcelain white glaze. maple hardwood.
P1791 2 1/4 57.2 274 124.3 • Use with steel clamp and
P1120 E 4 1/2 114.3 Everdur hardware. Order clamp
P1791 A 2 3/8 60.3 267 121.1 separately.
P1791 B 2 1/2 63.5 259 117.5
• Specify hole size when
P1791 C P1120 E 2 5/8 66.7 4 1/2 114.3 252 114.3 ordering.
P1793 C 3 5/8 92.1 450 204.1 P1691 P1115 E 1/2 – 1 12.7 – 25.4 2 1/8 54.0 42 19.1
P1794 3 3/4 95.3 712 323.0 P1692 P1117 E 3/4 – 1 1/2 19.1 – 38.1 2 5/8 66.7 54 24.5
P1794 A 3 7/8 98.4 696 315.7
P1124 E 7 1/4 184.2 P1693 P1118 E 1 1/4 – 1 3/4 31.8 – 44.5 3 76.2 65 29.5
P1794 B 4 101.6 683 309.8
P1794 C 4 1/8 104.8 670 303.9 P1694 P1119 E 1 1/2 – 2 1/4 38.1 – 57.2 3 5/8 92.1 84 38.1
P1795 4 1/4 108.0 645 292.6 P1695 P1120 E 2 – 2 1/2 50.8 – 63.5 4 1/8 104.8 107 48.5
P1795 A P1124 E 4 3/8 111.1 7 1/4 184.2 632 286.7 P1696 P1121 E 2 1/4 – 3 57.2 – 76.2 4 5/8 117.5 123 55.8
P1795 B 4 1/2 114.3 617 279.9
P1697 P1123 E 3 – 4 76.2 – 101.6 5 3/4 146.1 163 73.9
12
ELECTRICAL ACCESSORIES
CABLE SADDLES
P1753 FG 2"
P1754 FG A Assembly
(50.8) “A” Maximum
Number Cable Diameter Weight/C
P1753 PO In mm In mm Lbs kg
P1754 PO
P1753 FG 2 13/16 71.4 3 76.2 12 5.4
P1754 FG 3 3/4 95.3 4 1/2 114.3 17 7.7
P1753 PO 3 76.2 3 76.2 75 34.0
Material: FG - Fiberglass Reinforced Polyester. P1754 PO 4 101.6 4 1/2 114.3 95 43.1
PO - Dry Process White Glazed Porcelain.
• 3/8" flat head machine screw included. P2649 F 3 – 3 1/2 76.2 – 88.9 5 1/2 139.7 3 76.2 80 36.3
• Specify hole size when ordering. P2649 G 3 1/2 – 4 88.9 – 101.6 6 152.4 3 1/4 82.6 94 42.6
• Order channel nuts as required.
Material: Paraffin impregnated maple hardwood. P2649 H over 4 over 101.6
SWIVEL HANGERS
M2037 A M2137 A
M2250
M2050 M2150
Wt./C 18 lbs (8.2 kg) 1 3⁄4" 3
⁄8"
(44.5)
3 (9.5) Dia.
3 ⁄8"
⁄8" B
B
(9.5) Dia. (9.5) Dia. 1"
(24.5)
1"
(24.5)
A 3
⁄8" (9.5) Dia. 1
⁄2" - 13 Thd.
Part “B” Weight/C A 3
1 ⁄4"
Number “A” In mm Lbs kg
(44.5)
M2037 3/8" - 16 2 31/32" 67.5 23 10.4
1
M2050 1/2" - 13 2 3/4" 69.9 32 14.5 ⁄2" - 13 Thd.
M2137 3/8" - 16 2 29/32" 67.5 27 12.2
M2350
M2150 1/2" - 13 2 3/4" 69.9 45 20.4 Wt./C 20 lbs (9.1 kg)
13
TM
TECHNICAL DATA
UNISTRUT
TECHNICAL DATA
UNISTRUT
*Load limited by spot weld shear †Bearing load limited by capacity **KL > 200
r
NOTE: 1. Above loads include the weight of the member. This weight must be deducted to arrive at the net allowable load the
beam will support.
2. Long span beams should be supported in such a manner as to prevent rotation and twist.
3. Allowable uniformly distributed loads are listed for various simple spans, that is, a beam on two supports. If load is
concentrated at the center of the span, multiply load from the table by 0.5 and corresponding deflection by 0.8.
ELEMENTS OF SECTION
Axis 1 - 1 Axis 2 - 2
Channel Areas Of
Section l S r l S r
In2 cm2 In4 cm4 In3 cm3 In cm In4 cm4 In3 cm3 In cm
P1000 0.556 3.60 0.185 7.70 0.202 3.30 0.577 1.50 0.236 9.80 0.290 4.70 0.651 1.70
P1001 1.112 7.20 0.930 38.70 0.572 9.40 0.915 2.30 0.472 19.60 0.580 9.50 0.651 1.70
P1100 0.417 2.70 0.149 6.20 0.166 2.70 0.597 1.50 0.183 7.60 0.230 3.70 0.662 1.70
P1101 0.834 5.40 0.741 30.80 0.456 7.50 0.942 2.40 0.366 15.20 0.450 7.40 0.662 1.70
P2000 0.340 2.20 0.124 5.20 0.140 2.30 0.605 1.50 0.151 6.30 0.190 3.00 0.667 1.70
P2001 0.681 4.40 0.616 25.60 0.379 6.20 0.951 2.40 0.303 12.60 0.370 6.10 0.667 1.70
P3000 0.503 3.20 0.121 5.00 0.154 2.50 0.490 1.20 0.205 8.50 0.250 4.10 0.639 1.60
P3001 1.007 6.50 0.693 24.70 0.431 7.10 0.767 1.90 0.411 173.10 0.510 8.30 0.639 1.60
P3300 0.398 2.60 0.037 1.50 0.072 1.20 0.306 0.78 0.145 6.00 0.178 2.90 0.603 1.50
P3301 0.797 5.10 0.177 7.40 0.202 3.30 0.471 1.20 0.289 12.00 0.356 5.80 0.603 1.50
P4000 0.239 1.50 0.023 0.96 0.048 0.79 0.308 0.78 0.091 3.80 0.112 1.80 0.617 1.60
P4001 0.478 3.10 0.101 4.20 0.125 2.00 0.460 1.20 0.182 7.60 0.224 3.70 0.617 1.60 I - Moment of
P4100 0.284 1.90 0.025 1.00 0.053 0.90 0.298 0.80 0.106 4.40 0.130 2.10 0.609 1.50 Inertia
P4101 0.574 3.70 0.114 4.70 0.141 2.30 0.447 1.10 0.212 8.80 0.260 4.30 0.609 1.50
P5000 0.897 5.80 1.099 45.70 0.628 10.30 1.107 2.80 0.359* 14.90 0.442* 7.20 0.695 1.80 S - Section
P5001 1.794 11.60 5.578* 232.20 1.716* 28.10 1.864 4.70 0.719* 29.90 0.884* 14.50 0.695 1.80 Modulus
P5500 0.826 4.70 0.523 21.80 0.391 6.40 0.848 2.20 0.335 13.90 0.410 6.80 0.679 1.70
P5501 1.453 9.40 2.811 117.00 1.153 18.90 1.391 3.50 0.669 27.80 0.820 13.50 0.679 1.70 r - Radius of
Gyration
16
TECHNICAL DATA
ELEMENTS OF SECTION
RACEWAY DATA
UNISTRUT channel is listed by Underwriters’ P1000, &-KO, P1100, &-KO, P2000 &-KO P3000, &-KO
Laboratories as a surface metal raceway. Number & Conductor Size (AWG) Number & Conductor Size (AWG)
Snap-in closure strip is used to complete the 14Ga. 12Ga. 10Ga. 8Ga. 6Ga. 14Ga. 12Ga. 10Ga. 8Ga. 6Ga.
raceway. Accessory parts listed by THWN, THHN 88 66 42 20 14 THWN, THHN 72 54 34 17 12
Underwriters are noted on drawings. XHHW 58 46 35 16 12 XHHW 48 37 29 13 10
Tables show maximum number of conductors T, TW 57 44 34 16 9 T, TW 46 36 28 13 7
when raceway is not employed with fixtures THW 37 30 24 12 9 THW 30 25 20 10 7
or where the clearance between fixtures and RH 33 27 16 9 6 RH 27 22 13 7 5
raceway is greater than 1/2 inch. In all cases RHH, RHW 23 20 16 9 6 RHH, RHW 19 16 13 7 5
the snap-in cover is required to complete
raceway enclosure.
NOTE: Suitable for number of wires in Column A when installed to support and supply electric discharge type lighting fixtures when
raceway wiring is suitable for at least 75˚C except wire suitable for 60˚C may be used when clearance between fixtures and raceways is
at least 1/2 inch. Also suitable for number of wires in Column B when installed to support electric discharge type lighting fixtures when
raceway wiring is suitable for at least 75˚C and clearance between fixtures and raceway is a least 1/8 inch.
17
TM
TECHNICAL DATA
UNISTRUT
1. Simple Beam,
Uniform Load SPAN 1.00 1.00
2. Simple Beam,
Concentrated Load at Center .50 .80
3. Simple Beam,
Two Equal Concentrated Loads at 1/4 Pts. 1.00 1.10
6. Cantilever Beam,
Uniform Load .25 2.40
7. Cantilever Beam,
Concentrated Load at End .12 3.20
EXAMPLE I EXAMPLE II
PROBLEM: PROBLEM:
Determine load and deflection Determine load and deflection
of a P1000 beam continuous of a P5500 cantilever beam
over one support and loaded with a concentrated load on
uniformly on one span. 5' - 0" 5' - 0" the end. 3' - 0"
SOLUTION: SOLUTION:
A. From load table for P1000 on page 14 A. From load table for P5500 on page 14
load for a 5'-0" span is 680# and deflection is .35". load for a 3'-0" span is 2190# and deflection is .09".
B. Multiply by factors from table above. B. Multiply by factors from table above.
Load = 680# x 1.30 = 884# Load = 2190# x .12 = 263#
Deflection = .35" x .92 = .32" Deflection = .09" x 3.20 = .29"
18
GUIDE SPECIFICATION
Part One - General 2. Submit all shop/assembly drawings cleaning and phosphating, and
necessary to completely install the thoroughly baked. Color is per Federal
1.01 Scope of work Strut System in compliance with the Standard 595a color number 14109 (dark
A. Provide all Unistrut Metal Framing Contract Drawings. limit V-). Finish to withstand minimum
material, fittings and related accessories 3. Submit all pertinent manufacturers 400 hours salt spray when tested in
(Strut System) as indicated on the published data. accordance with ASTM B117.
Contract Drawings. 2. ELECTRO-GALVANIZED (EG)
B. Provide all labor supervision, engineering, 1.04 Product Delivery, Storage and Electrolytically zinc coated per ASTM
and fabrication required for installation Handling B 633 Type III SC 1
of the Strut System in accordance with A. All material is to be delivered to the work 3. PREGALVANIZED (PG)
the Contract Drawings and as specified site in original factory packaging to avoid Zinc coated by hot-dipped process
herein. damage to the finish. prior to roll forming. The zinc weight
C. Related work specified elsewhere. B. Upon delivery to the work site, all shall be G90 conforming to ASTM
components shall be protected from the A 653.
1.02 Quality Assurance elements by a shelter or other covering. 4. HOT-DIPPED GALVANIZED (HG)
A. Manufacturer’s qualifications: Zinc coated after all manufacturing
1.05 Guarantee operations are complete. Coating shall
1. The manufacturer shall not have had
less than 10 year’s experience in A. Separate guarantees shall be issued from conform to ASTM A 123 or A 153
manufacturing Strut Systems. the erector and manufacturer, valid for a 5. SPECIAL COATING / MATERIAL
period of one year, against any defects
2. The manufacturer must certify in (Describe as applicable)
that may arise from the installation or
writing all components supplied have
manufacture of the Strut System
been produced in accordance with an Part Three - Execution
components.
established quality assurance program.
B. Installer’s qualifications: 3.01 Examination
Part Two - Products
1. Installer must be a Unistrut trained A. The installer shall inspect the work area
manufacturer’s authorized 2.01 Acceptable Manufacturers prior to installation. If work area
representative/installer with not less conditions are unsatisfactory, installation
A. All Strut System components shall be as
than 5 years experience in the shall not proceed until satisfactory
manufactured by UNISTRUT
installation of Strut Systems of this size corrections are completed.
CORPORATION or approved equal as
and conformation. determined by the Architect or Engineer
3.02 Installation
2. All strut components must be supplied of record in writing 10 days prior to bid
date. A. Installation shall be accomplished by a
by a single manufacturer.
fully trained manufacturer authorized
C. Standards installer.
2.02 Materials
1. Work shall meet the requirements of B. Set Strut System components into final
the following standards: A. All channel members shall be fabricated
from structural grade steel conforming to position true to line, level and plumb, in
Federal, State and Local codes; accordance with approved shop
one of the following ASTM specifications:
American Iron and Steel Institute (AISI) drawings.
Specification for the Design of Cold- A 570 GR 33, A 653 GR33
C. Anchor material firmly in place. Tighten
Formed Steel Structural Members B. All fittings shall be fabricated from steel
all connections to their recommended
August 19, 1986 Edition, December 11, conforming to one of the following
torques.
1989 Addendum; American Society for ASTM specifications:
Testing And Materials (ASTM). A 575, A 576, A 36 or A 635 3.03 Cleanup
C. Substitutions A. Upon completion of the section of work,
1.03 Submittals Any substitutions of product or remove all protective wraps and debris.
A. Structural Calculations and Shop manufacturer must be approved in Repair any damage due to installation of
Drawings writing 10 days prior to bid date, by this section of work.
1. Submit structural calculations for Architect or Engineer of record.
approval by the project engineer. 3.04 Protection
Calculations may include, but are not 2.03 Finishes A. During installation, it shall be the
limited to: A. Strut System components shall be responsibility of the installer to protect
a. Description of design criteria. finished in accordance with one of the this work from damage.
b. Stress and deflection analysis. following standards: B. Upon completion of this scope of work, it
c. Selection of Unistrut framing 1. PERMA-GREEN II® (GR) shall become the responsibility of the
members, fittings and accessories. Rust inhibiting acrylic enamel paint general contractor to protect this work
applied by electro-deposition, after from damage during the remainder of
construction on the project and until
substantial completion.
The specifications, descriptions, information and illustrated material herein are submitted solely for evaluation by others and since the use of its products and information
is not within its control, Unistrut assumes no obligation or liability for such information and does not guarantee results from the use of said products or the information
herein. Reference should be made to original or primary source data along with standard accepted industry practice. The material herein is as of the date of publication
and is subject to change without notice.
19
CABLE TRAY BRACKETS
BEAM-MOUNTED BUSWAY SUPPORTS Unistrut Metal Framing and brackets form an
Various component types, sizes and ideal cable tray support system where tight
configurations can be quickly and easily quarters require maximum support flexibility
secured with the Unistrut system. in minimum space.
CEILING GRID
Drops for this grid are fabricated from
threaded rod suspended from Unistrut
channel, which is attached to the roof
structure with Unistrut beam clamps.
UNISTRUT
TM