Professional Documents
Culture Documents
Technical Data
Page
No.
1 - SELF - TAPPING SCREWS
Head Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Thread, Length Tolerances and Mechanical Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Recommended Hole Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
8 - RIVET BUSHES
Rivet Bushes - Round . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Rivet Bushes - Hexagon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
9 - SELF - CLINCHING FASTENERS
Clinch Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Clinch Flush Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Clinch Blind Standoffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Clinch Through Standoffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Clinch Studs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Clinch Studs - High Strength Non Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
10 - K- SERIES SETZMUTTERN
Standard Spigot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Intermediate Spigot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Long Spigot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
11 - CD WELD STUDS
Threaded - Type PT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Unthreaded - Type UT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Internally Threaded - Type IT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Coarse Threaded - Type CT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
TECHNICAL DATA 1
DIN 7504 SELF-DRILLING
Self-Tapping Screws
depending on the standard. depending on the standard.
BS 4174 referred to as Type AB BS 4174 referred to as Type B
DIN 7970 referred to as Type B DIN 7970 referred to as Type BZ
ISO 1478 referred to as Type C ISO 1478 referred to as Type F
Tolerances
SCREWS FOR PLASTIC
to BS 4174
FASTENERS FOR
SHEET METAL
Tolerances
to DIN 267
CD WELD STUDS
DEPTH
REF
BRASS INSERTS
FOR PLASTIC
Tolerances to
ISO 4759/1
TECHNICAL DATA
SCREWS
screws have various references have various references
Self-Tapping Screws
depending on the standard. depending on the standard.
BS 4174 referred to as Type AB BS 4174 referred to as Type B
DIN 7970 referred to as Type B DIN 7970 referred to as Type BZ
ISO 1478 referred to as Type C ISO 1478 referred to as Type F
SCREWS
MACHINE SCREWS
ROLLED THREAD
SCREWS FOR PLASTIC
FASTENERS FOR
SHEET METAL
CD WELD STUDS
Dimensions in Millimetres
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
TECHNICAL DATA 1
DIN 7504 SELF-DRILLING
SCREWS
Self-Tapping Screws
Due to the variety of the hardness of metals and the different operating
conditions, it may be found necessary to vary these dimensions which
should be used only as a guide.
DIN 7500 THREAD ROLLING
SCREWS
MACHINE SCREWS
ROLLED THREAD
Dimensions in Inches
CD WELD STUDS
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
TECHNICAL DATA 3
DIN 7504 SELF-DRILLING
SCREWS
DIN 7504
DIN 7504 - N DIN 7504 - P Similar
MACHINE SCREWS
Dimensions in Millimetres
SELF-DRILLING SCREWS
WITH WINGS AND UNDERHEAD RIBS
RECESS SIZE
METRIC
METRIC
GAUGE
GAUGE
FASTENERS FOR
SHEET METAL
SCREWS
Pan FORM C DIN 7985 Csk (90˚) FORM C DIN 965 Indented Washer Hex (Form D Equiv.) Socket Cap (Form E Equiv.)
HEX WASHER TOTAL DEPTH
Pozi Pozi A/F Max. Depth Max. DIA. MAX. DEPTH MAX. MAX. T-DRIVE A/F
- - - - - - - -
MACHINE SCREWS
ROLLED THREAD
- - - - - - - -
5.0 1.90 6.30 2.40 - - - -
- - - - - - - -
5.5/7 2.80/3.20 8.30/8.80 3.50/4.10 7.22 4.00 T20 3.00
8 3.40 10.40 4.50 8.72 5.00 T25 4.00
10 4.00 13.00 5.20 10.22 6.00 T30 5.00
13 5.60 16.90 7.00 13.27 8.00 T40 6.00
17 7.16 22.10 9.00 16.27 10.00 T50 8.00
FASTENERS FOR
SHEET METAL
CD WELD STUDS
Dimensions in Millimetres
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
TECHNICAL DATA 4
DIN 7504 SELF-DRILLING
SCREWS
Tap-Fix Screws ®
UNIFIED Series
Pozi Pozi
ROLLED THREAD
SCREWS FOR PLASTIC
Cp
FASTENERS FOR
SHEET METAL
CD WELD STUDS
BRASS INSERTS
FOR PLASTIC
Dimensions in Inches
TECHNICAL DATA
SCREWS
HEAD DIMENSIONS
SCREW SIZE
SCREW SIZE
PAN DIN 7985 CSK DIN 965
RECESS RECESS
MACHINE SCREWS
DIA. DEPTH DIA. DEPTH
ROLLED THREAD
MAX. MAX. Pozi T-Drive MAX. REF. Pozi T-Drive
M1.6 3.20 1.42 0 T5 3.00 0.96 0 T5 M1.6
M2 4.00 1.72 1 T6 3.80 1.20 1 T6 M2
M2.5 5.00 2.12 1 T8 4.70 1.50 1 T8 M2.5
M3 6.00 2.52 1 T10 5.60 1.65 1 T10 M3
M3.5 7.00 2.82 2 T15 6.50 1.93 2 T15 M3.5
LENGTH TOLERANCES
SCREW SIZE
SCREW SIZE
FASTENERS FOR
SHEET METAL
NOM LENGTH MM TOL. MM
M2 - M10
Dimensions in Millimetres
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
TECHNICAL DATA 5
DIN 7504 SELF-DRILLING
SCREWS
HEAD DIMENSIONS
SCREW SIZE
SCREW SIZE
PAN ANSI B1.1 CSK ANSI B1.1
LENGTH TOLERANCES
SCREW SIZE
SCREW SIZE
+ .00
2-56 UNC - 1/4-20 UNC
3/16” - 1”
- .03
FASTENERS FOR
SHEET METAL
+ .00
1 1/8” - 1 1/4”
- .06
Dimensions in Inches
CD WELD STUDS
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
SCREWS
Plas-Fix Screws ® METRIC Series
45˚ Thread
SCREWS
Pan Csk (90˚) Flange
MACHINE SCREWS
Pozi Pozi
ROLLED THREAD
Pozi
1 1
FASTENERS FOR
SHEET METAL
CD WELD STUDS
TECHNICAL DATA 6
DIN 7504 SELF-DRILLING
60o
v
SCREWS
Dimensions in Inches
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
SCREWS
Plas-Tech 30 Screws ® METRIC Series
30˚ Thread
SCREWS
METRIC SERIES HEAD DIMENSIONS
SCREW SIZE
SCREW SIZE
Pan Csk (90º) Flange
MACHINE SCREWS
ROLLED THREAD
DIA. MAX DEPTH MAX RECESS SIZE Absolute RECESS SIZE RECESS SIZE
Max. Dia.
DEPTH DIA. DEPTH
REF MAX MAX
Pozi T-Drive Pozi T-Drive Pozi T-Drive (Sharp Edge) Pozi T-Drive Pozi T-Drive
2.2 x 0.98 3.90 - 1.50 - 1 T6 3.80 1.30 1 T6 4.40 1.60 1 T6 2.2 x 0.98
2.5 x 1.12 4.40 4.20 1.70 1.60 1 T7 4.70 1.75 1 T8 5.00 1.80 1 T6 2.5 x 1.12
3.0 x 1.34 5.30 5.60 2.00 2.10 1 T10 5.50 2.05 1 T8 6.00 2.10 1 T10 3.0 x 1.34
3.5 x 1.57 6.10 6.90 2.50 2.30 2 T10 7.30 2.80 2 T15 7.00 2.40 2 T10 3.5 x 1.57
4.0 x 1.79 7.00 7.50 2.70 2.60 2 T20 8.40 3.25 2 T20 8.00 2.50 2 T20 4.0 x 1.79
6.0 x 2.69 10.50 - 4.00 - 3 T25 11.30 3.80 2 T30 12.00 4.00 3 T25 6.0 x 2.69
FASTENERS FOR
SHEET METAL
CD WELD STUDS
TECHNICAL DATA 6
DIN 7504 SELF-DRILLING
40o
v
SCREWS
SCREW SIZE
SCREW SIZE
MACHINE SCREWS
ABSOLUTE
DIA. DEPTH RECESS MAX. DIA. DEPTH RECESS DIA. DEPTH RECESS
MAX. MAX. Pozi T-Drive
(Sharp REF. Pozi T-Drive MAX. MAX. Pozi T-Drive
Edge)
3.0 x 1.20 5.60 2.20 1 T10 6.00 1.50 1 T8 6.00 2.22 1 T10 3.0 x 1.20
3.5 x 1.40 6.90 2.60 2 T10 7.00 1.85 2 T15 7.00 2.52 2 T10 3.5 x 1.40
4.0 x 1.60 7.50 2.80 2 T20 8.00 2.10 2 T20 8.00 2.62 2 T20 4.0 x 1.60
SCREWS FOR PLASTIC
5.0 x 2.00 9.50 3.55 2 T20 10.00 2.60 2 T20 10.00 3.35 2 T20 5.0 x 2.00
6.0 x 2.40 10.80 3.95 3 T25 12.00 3.10 3 T25 12.00 4.15 3 T25 6.0 x 2.40
NOM
NOM TOL
LENGTH
d d1 POLY POLY SIZE MM
ABS NYLON MM
MAX MIN NOM PROP CARB
UP TO 10.00
3.0 x 1.20 3.00 2.85 1.50 2.75 2.60 2.50 2.75 +0.00 / -0.80
2.5 - 5.0 10.00 to 20.00
CD WELD STUDS
SCREWS
POZI
Pan Flange Csk (80˚)
MACHINE SCREWS
ROLLED THREAD
Dimensions in Millimetres
Dimensions in Millimetres
TECHNICAL DATA
TECHNICAL DATA 6
DIN 7504 SELF-DRILLING
SCREWS
POZI
Pan Flange Csk (80˚)
MACHINE SCREWS
ROLLED THREAD
Dimensions in Millimetres
SCREWS FOR PLASTIC
FASTENERS FOR
SHEET METAL
CD WELD STUDS
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
SCREWS
POZI
Pan Flange Csk (80˚)
MACHINE SCREWS
ROLLED THREAD
SCREWS FOR PLASTIC
N.B. As there are no BS Standards for HIGH-LOW head sizes,
they are generally offered 1 diameter smaller than self-
Tolerances to DIN 267
tapping screws. However, this should be checked prior to Dimensions in Millimetres
ordering if this factor is important.
FASTENERS FOR
SHEET METAL
CD WELD STUDS
Dimensions in Millimetres
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
TECHNICAL DATA 8
DIN 7504 SELF-DRILLING
SCREWS
Rivet Bushes B A
C
DIN 7500 THREAD ROLLING
Round
SCREWS
Technical Data
METRIC M2.5 M3 M3.5 M4 M5 M6 M8 M10 M12
Diameter of spigot METRIC 5.54 5.54 6.73 6.73 7.92 9.52 12.70 15.87 19.05
A
+ 0.00mm - 0.13mm IMPERIAL .218 .218 .265 .265 .312 .375 .500 .625 .750
Diameter of body METRIC 7.92 7.92 9.52 9.52 11.10 12.70 15.87 19.05 25.40
B
+/- 0.13mm
SCREWS FOR PLASTIC
IMPERIAL .312 .312 .375 .375 .437 .500 .625 .750 1.000
Depth of body METRIC 3.17 3.17 3.17 3.17 3.81 5.08 6.35 7.62 10.16
C
+ / - 0.13mm IMPERIAL .125 .125 .125 .125 .150 .200 .250 .300 .400
Recommended hole size METRIC 5.54 5.54 6.73 6.73 7.92 9.52 12.70 15.87 19.05
+ 0.05mm - 0.00mm IMPERIAL .218 .218 .265 .265 .312 .375 .500 .625 .750
Test Results*
FASTENERS FOR
1.0mm 1.2mm 1.5/1.6mm 2.0mm 2.5mm 3.0mm 1.0mm 1.2mm 1.5/1.6mm 2.0mm 2.5mm 3.0mm
(20swg) (18swg) (16swg) (14swg) (12swg) (10swg) (20swg) (18swg) (16swg) (14swg) (12swg) (10swg)
M3 3.2 3.9 4.4 4.7 5.6 6.9 1649 1730 1741 1810 1950 2021
M4 7.0 7.9 8.4 9.8 9.4 9.6 2610 2716 2841 3250 3271 2124
M5 9.2 10.4 11.6 13.0 16.0 17.2 3620 3551 3829 4210 4310 4400
M6 16.2 16.8 18.9 24.2 25.4 28.3 3944 4418 4715 5230 5145 5010
M8 25.4 26.9 33.2 34.4 34.7 39.2 4740 4885 5374 5489 6219 6384
CD WELD STUDS
M10 32.8 38.4 41.8 42.9 45.3 48.9 4936 5245 5490 5820 6481 6539
* These tests have been conducted using steel product in cold rolled steel, in a controlled test environment. These performance figures
should be used for guidance only.
Sheet Anvil
SCREWS
Technical Data
METRIC M2.5 M3 M3.5 M4 M5 M6 M8 M10 M12
MACHINE SCREWS
ROLLED THREAD
UNC 2 4 6 8 10 1/4” 5/16” 3/8” 1/2”
UNF 2 4 6 8 10 1/4” 5/16” 3/8” 1/2”
Diameter of spigot METRIC 5.54 5.54 6.73 6.73 7.92 9.52 12.70 15.87 19.05
+ 0.00mm - 0.13mm A
IMPERIAL .218 .218 .265 .265 .312 .375 .500 .625 .750
Width across flats METRIC 7.92 7.92 7.92 7.92 9.52 11.10 14.27 19.05 22.22
+/- 0.115m B
Recommended hole size METRIC 5.54 5.54 6.73 6.73 7.92 9.52 12.70 15.87 19.05
+ 0.05mm - 0.00mm IMPERIAL .218 .218 .265 .265 .312 .375 .500 .625 .750
Test Results*
FASTENERS FOR
Torsional Resistance in ‘Nm’ (Newton Meters) Pull Out in ‘N’ (Newtons)
SHEET METAL
1.0mm 1.2mm 1.5/1.6mm 2.0mm 2.5mm 3.0mm 1.0mm 1.2mm 1.5/1.6mm 2.0mm 2.5mm 3.0mm
(20swg) (18swg) (16swg) (14swg) (12swg) (10swg) (20swg) (18swg) (16swg) (14swg) (12swg) (10swg)
M3 3.1 4.0 4.2 4.8 5.6 6.8 1656 1720 1748 1822 1945 2016
M4 7.3 8.0 8.2 9.4 9.4 9.7 2640 2710 2814 3223 3287 3156
M5 9.8 10.1 11.5 13.2 15.9 17.1 3514 3584 3820 4199 4208 4357
M6 16.1 17.0 19.2 23.9 25.6 28.4 3920 4425 4690 5210 5120 5040
M8 25.9 27.1 34.0 34.6 35.1 38.9 4710 4916 5360 5480 6210 6387
CD WELD STUDS
M10 32.3 37.2 42.3 43.8 44.8 49.8 4982 5210 5560 5810 6490 6538
* These tests have been conducted using steel product in cold rolled steel, in a controlled test environment. These performance figures
should be used for guidance only.
Sheet Anvil
TECHNICAL DATA 9
DIN 7504 SELF-DRILLING
SCREWS
Self-Clinching Fasteners D B
h H
DIN 7500 THREAD ROLLING
Clinch Nuts
SCREWS
Technical Data
-0 0.77 0.8 - 1
MACHINE SCREWS
ROLLED THREAD
M2.5
0.45 -1 4.22 6.3 1.5 0.97 1.0 4.25 4.8
-2 1.38 1.4
-0 0.76 0.8
M3
0.5 -1 4.22 6.3 1.5 0.97 1.0 4.25 4.8
-2 1.37 1.4
-0 0.76 0.8
M3 Alt*
0.5 -1 4.73 7.1 1.5 0.97 1.0 4.75 5.6
SCREWS FOR PLASTIC
-2 1.37 1.4
Metric (dimensions in ‘mm’)
-0 0.76 0.8
M3.5
0.6 -1 4.73 7.1 1.5 0.97 1.0 4.75 5.6
-2 1.37 1.4
-0 0.76 0.8
M4
0.7 -1 5.38 7.9 2.0 0.97 1.0 5.4 6.9
-2 1.37 1.4
-0 0.76 0.8
M5
-1 6.38 8.7 2.0 0.97 1.0 6.4 7.1
FASTENERS FOR
0.8
SHEET METAL
-2 1.37 1.4
M6 -1 1.37 1.4
1.0 8.72 11.05 4.1 8.75 8.6
-2 2.21 2.3
M8 -1 1.37 1.4
1.25 10.44 12.65 5.5 10.5 9.7
-2 2.21 2.3
M10 -1 2.21 2.31
1.5 13.97 17.35 7.48 14 13.5
-2 3.05 3.18
CD WELD STUDS
Steel Self Clinch Nuts are suitable for use in sheet steel with a maximum hardness of HRB80.
Stainless Steel Self Clinch Nuts are suitable for use in sheet steel with a maximum hardness of HRB70.
For Sheet Steel with a greater hardness, Rivet Bushes are recommended.
Punch
BRASS INSERTS
Nut
FOR PLASTIC
Sheet Anvil
SCREWS
Self-Clinching Fasteners B D D
H H
SCREWS
Technical Data
Thread D B h Minimum Rec. Hole Size Minimum Distance
Code
& Pitch Max +/- 0.2 max Sheet Thickness + 0.08 - 0.00 to edge of Sheet
MACHINE SCREWS
M3
ROLLED THREAD
0.5 4.35 4.8 4.4 6.0
-2 2.3 2.4
Metric (dimensions in ‘mm’)
FASTENERS FOR
SHEET METAL
Technical Data
C
Thread A Minimum
+ 0.0 Length in mm + / - 0.20
& Pitch Nom Minimum Rec. Hole Size Distance
- 0.13
Sheet Thickness + 0.08 - 0.00 to
edge of Sheet
Length Codes 6 8 10 12 14 16 18 20 22 25
M3
4.18 4.8 6 8 10 12 14 16 18 20 22 25 1.0 4.2 6
CD WELD STUDS
Metric (dimensions in ‘mm’)
0.5
M3 Alt
0.5 5.39 6.4 6 8 10 12 14 16 18 20 22 25 1.0 5.4 6.8
M4
0.7 7.10 7.9 6 8 10 12 14 16 18 20 22 25 1.3 7.2 8
M5
0.8 7.10 7.9 6 8 10 12 14 16 18 20 22 25 1.3 7.2 8
Dimensions
BRASS INSERTS
FOR PLASTIC
Length (mm) 6 8 10 12 14 16 18 20 22 25
Steel Clinch Blind Standoffs are suitable for use in sheet steel with a maximum hardness of HRB70.
Stainless Steel Clinch Blind Standoffs are suitable for use in sheet steel with a maximum hardness of HRB70.
For Sheet Steel with a greater hardness, Rivet Bushes are recommended.
TECHNICAL DATA
TECHNICAL DATA 9
DIN 7504 SELF-DRILLING
SCREWS
Self-Clinching Fasteners
DIN 7500 THREAD ROLLING
Technical Data
C
Thread A Minimum
+ 0.0 D Length in mm + / - 0.20
& Pitch Nom Minimum Rec. Hole Size Distance
- 0.13
Sheet Thickness + 0.08 - 0.00 to
edge of Sheet
Length Codes 6 8 10 12 14 16 18 20 22 25
MACHINE SCREWS
M2.5
ROLLED THREAD
M3
0.5 4.18 3.2 4.8 6 8 10 12 14 16 18 20 22 25 1.0 4.2 6
M3 Alt
0.5 5.39 3.2 6.4 6 8 10 12 14 16 18 20 22 25 1.0 5.4 6.8
M4
0.7 7.10 4.8 7.9 6 8 10 12 14 16 18 20 22 25 1.3 7.2 8
M5
0.8 7.10 5.2 7.9 6 8 10 12 14 16 18 20 22 25 1.3 7.2 8
SCREWS FOR PLASTIC
Dimensions
Length (mm) 6 8 10 12 14 16 18 20 22 25
Steel Clinch Through Standoffs are suitable for use in sheet steel with a maximum hardness of HRB70.
Stainless Steel Clinch Through Standoffs are suitable for use in sheet steel with a maximum hardness of HRB70.
For Sheet Steel with a greater hardness, Rivet Bushes are recommended.
FASTENERS FOR
SHEET METAL
Clinch Studs
Technical Data
Metric (Dimensions in mm)
CD WELD STUDS
Min Hole
Thread D H Min Distance
Rec Sheet + 0.08
Size + / - 0.4 Max to edge of sheet
Thickness - 0.0
Steel Clinch Studs are suitable for use in sheet steel with a maximum hardness of HRB70.
Stainless Steel Clinch Studs are suitable for use in sheet steel with a maximum hardness of HRB70.
For Sheet Steel with a greater hardness, Rivet Bushes are recommended.
TECHNICAL DATA
SCREWS
Self-Clinching Fasteners
D H
SCREWS
Technical Data
Metric (Dimensions in mm)
Min Hole
Thread D H B Min Distance
Rec Sheet + 0.13
Size + / - 0.4 Max Max to edge of sheet
MACHINE SCREWS
Thickness - 0.0
ROLLED THREAD
M8 12.5 3.5 1.78 2.0 8.0 12.7
M10 15.7 4.1 2.30 2.4 10.0 13.7
Steel High Strength Clinch Studs are suitable for use in sheet steel with a maximum hardness of HRB85.
TECHNICAL DATA 10
DIN 7504 SELF-DRILLING
Setzmutter
SCREWS
K-SERIES
A/F h
h1
d1
d2
DIN 7500 THREAD ROLLING
Standard Spigot
SCREWS
Spigot Length
Thread Across Hole Material
h d1 d2
Size Flats A/F Diameter Thickness
h1
MACHINE SCREWS
ROLLED THREAD
+ 0.00 + 0.05
M2.5 3.00 + / - 0.13 0.90 - 0.13
5.50 + / - 0.1 4.50 4.50 - 0.13
4.70 + / - 0.13 1 mm
+ 0.00 + 0.05
M3 3.00 + / - 0.13 0.90 - 0.13
5.50 + / - 0.1 4.50 4.50 - 0.13
4.70 + / - 0.13 1 mm
+ 0.00 + 0.05
M4 3.20 + / - 0.13 0.90 - 0.13
7.00 + / - 0.1 5.50 5.50 - 0.13
5.70 + / - 0.13 1 mm
+ 0.00 + 0.05
M5 4.00 + / - 0.13 0.90 8.00 + / - 0.1 6.50 6.50 6.75 + / - 0.13 1 mm
SCREWS FOR PLASTIC
- 0.13 - 0.13
+ 0.00 + 0.05
M6 5.00 + / - 0.13 0.90 - 0.13
10.00 + / - 0.1 8.00 8.00 - 0.13
8.30 + / - 0.13 1 mm
+ 0.00 + 0.05
M8 6.50 + / - 0.15 1.80 - 0.15
13.00 + / - 0.13 10.00 10.00 - 0.15
10.30 + / - 0.15 2 mm
+ 0.00 + 0.05
M10 8.00 + / - 0.15 1.80 - 0.15
15.00 + / - 0.13 12.50 12.50 - 0.15
12.85 + / - 0.15 2 mm
+ 0.00 + 0.05
M12 10.00 + / - 0.15 2.80 - 0.15
17.00 + / - 0.15 14.50 14.50 - 0.15
14.85 + / - 0.15 3 mm
FASTENERS FOR
SHEET METAL
+ 0.00 + 0.05
M16 13.00 + / - 0.20 2.40 - 0.15
22.00 + / - 0.20 18.50 18.50 - 0.20
18.85 + / - 0.20 3 mm
+ 0.00 + 0.05
M20 16.00 + / - 0.20 3.90 - 0.20
27.00 + / - 0.20 23.00 23.00 - 0.20
23.40 + / - 0.20 4 mm
SCREWS
K-SERIES
A/F h
h1
d1
d2
SCREWS
Metric (Dimensions in mm)
Spigot Length
Thread Across Hole Material
h d1 d2
Size Flats A/F Diameter Thickness
h1
MACHINE SCREWS
ROLLED THREAD
+ 0.00 + 0.05
M2.5 3.00 + / - 0.13 1.40 - 0.13
5.50 + / - 0.1 4.50 4.50 - 0.13
4.70 + / - 0.13 1.5 mm
+ 0.00 + 0.05
M3 3.00 + / - 0.13 1.40 - 0.13
5.50 + / - 0.1 4.50 4.50 - 0.13
4.70 + / - 0.13 1.5 mm
+ 0.00 + 0.05
M4 3.20 + / - 0.13 1.40 - 0.13
7.00 + / - 0.1 5.50 5.50 - 0.13
5.70 + / - 0.13 1.5 mm
+ 0.00 + 0.05
M5 4.00 + / - 0.13 1.40 - 0.13
8.00 + / - 0.1 6.50 6.50 - 0.13
6.75 + / - 0.13 1.5 mm
h
A/F
FASTENERS FOR
h1
SHEET METAL
d1
Long Spigot d2
Spigot Length
Thread Across Hole Material
h d1 d2
Size Flats A/F Diameter Thickness
h1
+ 0.00 + 0.05
M2.5 3.00 + / - 0.13 1.80 - 0.13
5.50 + / - 0.1 4.50 4.50 - 0.13
4.70 + / - 0.13 2 mm
+ 0.00 + 0.05
M3 3.00 + / - 0.13 1.80 - 0.13
5.50 + / - 0.1 4.50 4.50 - 0.13
4.70 + / - 0.13 2 mm
+ 0.00 + 0.05
M4 4.50 + / - 0.13 1.80 - 0.13
7.00 + / - 0.1 5.50 5.50 - 0.13
5.70 + / - 0.13 2 mm
BRASS INSERTS
FOR PLASTIC
+ 0.00 + 0.05
M5 5.00 + / - 0.13 1.80 - 0.13
8.00 + / - 0.1 6.50 6.50 - 0.13
6.75 + / - 0.13 2 mm
+ 0.00 + 0.05
M6 5.00 + / - 0.13 1.80 - 0.13
10.00 + / - 0.1 8.00 8.00 - 0.13
8.30 + / - 0.13 2 mm
TECHNICAL DATA 10
11
DIN 7504 SELF-DRILLING
D
SCREWS
L2
CD Weld Studs
L
B
A
a
L1
D2
DIN 7500 THREAD ROLLING
D1
Threaded - PT
SCREWS
L D1 D2 L1 B a
D + 0.6 A L2
+ / - 0.2 + / - 0.08 + / - 0.05 max. + / - 1º
- 0.0
MACHINE SCREWS
ROLLED THREAD
M3 4.5 0.60
0.55 0.7 - 1.4 1.5
See Dimensions
M4 5.5 0.65
L
M5 6.5 3º
0.80 2 - 0.3
M6 7.5 0.75 0.8 - 1.4
M8 9.0 0.85 3
SCREWS FOR PLASTIC
L2
L
FASTENERS FOR
A
SHEET METAL
a
L1
Unthreaded - UT D2
D1
L
D D1 D2 L1 a
A L2
CD WELD STUDS
+ 0.6
+ / - 0.1 + / - 0.2 + / - 0.08 + / - 0.05 + / - 1º
- 0.0
ø3 4.5 0.60
0.55 0.7 - 1.4
See Dimensions
ø4 5.5 0.65
L
ø5 6.5 3º
0.80 - 0.3
ø6 7.5 0.75 0.8 - 1.4
ø 7,1 9.0 0.85
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
SCREWS
C
CD Weld Studs
L
L2
A
a
L1
SCREWS
Metric (Dimensions in mm)
L
D D1 D2 L1 B a
+ / - 0.1
+ 0.6 A D3 C L2
+ / - 0.2 + / - 0.08 + / - 0.05 + / - 0.05 + / - 1º
- 0.0
MACHINE SCREWS
ROLLED THREAD
ø5 6.5 M3 5 2.5
See Dimensions
0.80
ø6 7.5 M4 6 3
0.8 - 1.4
L
0.75 3º
ø 7,1 M5 3 - 0.3
9.0 0.85 7.5
ø8 M6 3
L2
L
A
a
FASTENERS FOR
L1
SHEET METAL
D2
D1
Coarse Threaded - CT
L D1 D2 L1 a
CD WELD STUDS
D
+ / - 0.1
+ 0.6 A L2
+ / - 0.2 + / - 0.08 + / - 0.05 + / - 1º
- 0.0
L
ø5 See
Dimensions 6.5 0.75 0.80 0.8 - 1.4 3º
- 0.3
BRASS INSERTS
FOR PLASTIC
TECHNICAL DATA
TECHNICAL DATA 12
10
DIN 7504 SELF-DRILLING
SCREWS
Recommended Hole Size mm (-0.0/+0.1) 3.2 4.0 4.0 4.8 5.6 6.4 8.0 9.6 11.9
Minimum Wall Thickness mm 1.3 1.6 1.6 1.8 2.1 2.6 3.3 4.5 6.0
FASTENERS FOR
SHEET METAL
Minimum Wall Thickness mm 1.3 1.6 1.6 1.8 2.1 2.6 3.3 4.5 6.0
FOR PLASTIC
TECHNICAL DATA
SCREWS
Metric M2 M2.5 M3 M3.5 M4 M5 M6 M8
MACHINE SCREWS
ROLLED THREAD
UNF UNF UNF
FASTENERS FOR
SHEET METAL
Fin-Fix Unheaded (UHDFINFIX) Headed (HDFINFIX)
Thread Size
UNC UNC UNC
Unified 2.56 UNC - 4.40 UNC 6.32 UNC 8.32 UNC
10.32 1/4-28 5/16-24
UNF UNF UNF
N mm
Recommended Hole Size mm (-0.0/+0.1) 3.2 4.0 4.0 4.8 5.6 6.4 8.0 9.6
Minimum Wall Thickness mm 1.6 2.0 2.0 2.4 2.8 3.2 4.0 4.8
TECHNICAL DATA
TECHNICAL DATA 12
10
DIN 7504 SELF-DRILLING
SCREWS
Recommended Hole Size mm (-0.0/+0.1) 3.1 3.8 3.8 4.6 5.4 6.2 7.8 9.3 12.3
Minimum Wall Thickness mm 1.6 2.0 2.0 2.5 2.5 2.5 2.8 3.8 5.0
FASTENERS FOR
SHEET METAL
Thread Size
UNC UNC UNC
Unified 2.56 UNC - 4.40 UNC 6.32 UNC 8.32 UNC
10.32 1/4-28 5/16-24
UNF UNF UNF
Recommended Hole Size mm (-0.0/+0.1) 3.2 4.0 4.0 4.8 5.6 6.4 8.0 9.6
FOR PLASTIC
Minimum Wall Thickness mm 2.4 3.2 3.2 3.6 4.0 4.8 6.0 7.0
TECHNICAL DATA
SCREWS
Metric M2.5 M3 M3.5 M4 M5 M6 M8 M10
MACHINE SCREWS
ROLLED THREAD
UNF UNF UNF UNF
FASTENERS FOR
SHEET METAL
Flow-Fix Unheaded (UHDFLOFIX)