Professional Documents
Culture Documents
DEVRAN 201
Universal Epoxy Primer
Cat. # 201B0245/201C0300
DANGER! FLAMMABLE. HARMFUL OR FATAL IF SWALLOWED. Read label and Material Safety Data
Sheet Prior to Use. See other cautions on last page. DSF3-0696
Back Page: 201B0245/201C0300
GENERAL SURFACE PREPARATION
Surfaces must be sound, dry, clean, free of oil, grease, dirt, mildew, form release agents, followed by a thorough water rinsing and then prime with this product.
curing compounds, loose and flaking paint and other foreign substances.
Previously Painted Surfaces: If the old paint is more than 25% failed by rusting,
New Surfaces: Steel –Best results are obtained over a surface abrasive-blasted to a Near peeling, or flaking, it must be removed and treated as a new surface. If less than
White Blast (SSPC-SP10, ISO-Sa2 1/2). 1Performance over hand or power-tool cleaned 25% has failed, clean the failed areas and spot-prime with this product. Old coatings
surfaces is dependent on the degree of cleaning. Concrete and Masonry – Cure at least should be tested for lifting. If they lift, remove them. Scuff sand glossy areas and
30 days before painting. pH must be 10.0 or lower. Roughen slick poured or pre-cast aged epoxy coatings.
concrete by acid etching or sand sweeping. Follow acid manufacturer’s application and
safety instructions. Rinse thoroughly and allow to dry. Remove loose aggregate. Prime with WARNING! If you scrape, sand, or remove old paint, you may release lead
this product. Galvanized Steel – Allow to weather a minimum of six (6) months prior to dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
coating. Solvent clean per SSPC-SP-1 or clean with DEVPREP® 88 or other suitable ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT
cleaner followed by thorough water rinsing, then prime with this product. When weathering WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
is not possible or the surface has been treated with chromates or silicates, first clean by respirator to control lead exposure. Clean up carefully with a HEPA vacuum
the method intended to be used on the job and apply a test patch of the coating system and a wet mop. Before you start, find out how to protect yourself and your
specified. Allow product(s) to dry and cure at least one week before testing adhesion per family by contacting the National Lead Information Hotline at 1-800-424-LEAD
ASTM D 3359. If adhesion is poor, brush blast then prime with this product. Aluminum – or log on to www.epa.gov/lead.
Remove oils and dirt by solvent cleaning or with DEVPREP 88 or other suitable cleaner
PRECAUTIONS
DANGER! FLAMMABLE LIQUID AND VAPOR. CAUSES EYE AND SKIN BURNS. HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD-CAN ENTER LUNGS
AND CAUSE DAMAGE. HARMFUL IF INHALED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES
RESPIRATORY TRACT IRRITATION. MAY CAUSE ALLERGIC SKIN REACTION. MAY BE HARMFUL IF ABSORBED THROUGH SKIN. OVEREXPOSURE MAY CAUSE
BLOOD, LIVER, KIDNEY DAMAGE. CONTAINS CRYSTALLINE SILICA WHICH CAN CAUSE LUNG CANCER AND OTHER LUNG DAMAGE IF INHALED. CONTAINS MICA
WHICH MAY CAUSE PNEUMOCONIOSIS. POTENTIAL CANCER HAZARD. CONTAINS FORMALDEHYDE WHICH HAS BEEN SHOWN TO CAUSE UPPER RESPIRATORY
TRACT CANCER AND ALLERGIC RESPIRATORY REACTION. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN. NOTICE:
Products in this series contain solvents. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system
damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. For emergency information call (800) 545-2643. Note: These
warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information. Keep away from heat, sparks and flame. Do not
smoke. Vapors may ignite. Extinguish all flames, burners, stoves, heaters and pilot lights and disconnect all electrical motors and appliances before use and until all vapors are
gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. If sanding is done, wear a dust mask to avoid breathing of sanding dust. Do not
breathe vapors or spray mist. Ensure fresh air entry during application and drying. Avoid contact with eyes and skin. If you experience eye watering, headaches, or dizziness, leave
the area. If properly used, a respirator may offer additional protection. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin
contact, wash thoroughly with soap and water. If any product remains, gently rub petroleum jelly, vegetable or mineral/baby oil onto skin, then wash again with soap and water.
Repeated applications may be needed. Remove contaminated clothing. For eye contact, flush immediately with large amounts of water, for at least 15 minutes. Obtain emergency
medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing
difficulty occurs, get medical help. KEEP FROM FREEZING.
DS207-1003
SHIPPING
Flash point: 80°F (27°C) Shipping Weight: 4 - 1 gallon kits - 52.5 lbs. (23.8 kg)
Packaging: 1 gallon kit (3.785L) 5 gallon kit (18.925L) 5 gallon kit - 61 lbs. (27.7 kg)
0.90 gallon base 4.50 gallon base
0.10 gallon converter 0.50 gallon converter
201 (05/07)
Ad Stock #68672F