Professional Documents
Culture Documents
Relief Cartridge Valves Page 39: The PV*A-8 is a normally open modulating element
with a T-8A cavity in the end and an external drain. This
Page 9: The RP*S is a seated style pilot operated relief valve.
would enable any Sun pilot valve, such as the RBAP
This provides reduced leakage, faster response and a
proportional valve, to be fitted into the end to make a
reduced pressure overshoot to give improved pressure
proportional pressure reducing/relieving valve with
control.
external drain.
Page 10: The RPGT is a "soft start" relief valve available in
series 2 only providing a pressure ramping over 300
milliseconds when it opens to provide excellent pressure Page 40 and 41: The PRD* is an electro-proportional, direct
protection and reduce shock. acting, pressure reducing/relieving valve available in
series 1 only. There are two versions available, one with
Page 13: The RBAP is an electro-proportional, direct acting
low leakage and the other with higher leakage and
pilot relief valve that fits into the Sun T-8A cavity. It can
improved response.
be used as a pilot valve on it's own or together with many
types of main stage pressure control valves that have the
T-8A cavity in the end of the cartridge. Flow Control Cartridge Valves
Page 14: The RP*C-8 is a normally closed spool type
Page 73: The FPCC is an electro-proportional, normally
modulating valve, with a T-8A cavity in the end. This
closed throttle valve available in series 1 only. It provides
would enable any of the Sun pilot valves, such as the
some pressure compensation but needs a separate
RBAP proportional valve, to be fitted into the end to
compensator for more accurate control.
make a high capacity proportional relief valve.
Page 15: The RP*S-8 is a seated style normally closed
Page 74: The FPCH is an electro-proportional, normally open
modulating valve, with a T-8A cavity in the end. This
throttle valve available in series 1 only. It provides some
would enable any of the Sun pilot valves, such as the
pressure compensation but needs a separate compensator
RBAP proportional valve, to be fitted into the end to
for more accurate control.
make a proportional relief valve with low leakage on the
main stage.
Page 18: The RV*S is a ventable, seated style, pilot operated Priority Flow Control Cartridge Valves
relief valve. This provides reduced leakage, faster
Page 78: The FV*A-8 is a ventable, fixed orifice, priority flow
response and a reduced pressure overshoot to give
control valve with a T-8A cavity in the end of the
improved pressure control.
cartridge. This enables a Sun pilot solenoid, pneumatic or
Page 20: The RV*D-8 is a normally closed, balanced piston, manual valve to be fitted into the cartridge to select the
modulating element with a T-8A cavity in the end. The priority flow condition or bypass all flow to tank.
cartridge is ventable and also has an external drain
connection. This would enable any Sun pilot valve, such
as the RBAP proportional valve, to be fitted into the end Logic Elements
to make a ventable proportional relief with separate drain
Page 89: The LO**-8 is a poppet type, spring biased closed,
port.
pilot-to-close unbalanced logic valve with a T-8A cavity
Sequence Cartridge Valves in the end of the cartridge. This enables a Sun pilot
solenoid, pneumatic or manual valve to be fitted into the
Page 23: The RSDC-8 is a normally closed, balanced piston,
cartridge to select the valve in the open or closed
modulating element with a T-8A cavity in the end and
condition.
external drain. This would enable any Sun pilot valve
such as the RBAP proportional valve to be fitted into the
end to make a relief valve with separate pilot drain.
Page 95: The DO*R-8 is a poppet type, pilot-to-close,
normally open balanced logic valve with a T-8A cavity in
Reducing/Relieving Cartridge Valves the end of the cartridge. This enables a Sun pilot solenoid,
Page 37: The PB*B-8 is a normally open modulating element pneumatic or manual valve to be fitted into the cartridge
with a T-8A cavity in the end. This would enable any Sun to select the valve in the open or closed condition.
pilot valve such as the RBAP proportional valve to be
fitted to make a proportional pressure reducing valve. Page 100: The DK*R-8 is a poppet type, pilot-to-open,
Page 38: The PP*B-8 is a normally open modulating element normally closed balanced logic valve with a T-8A cavity
with a T-8A cavity in the end. This would enable any Sun in the end of the cartridge. This enables a Sun pilot
pilot such as the RBAP proportional valve to be fitted into solenoid, pneumatic or manual valve to be fitted into the
the end to make a proportional pressure reducing/ cartridge to select the valve in the open or closed
relieving valve. condition.
Sun Hydraulics reserves the right to discontinue models at any time, or change prices, specifications
or designs without notice or incurring obligation.
All rights reserved. This book, or any part thereof, may not be reproduced or transmitted in any form
or by any means, electronic or mechanical, including photocopying, recording,
or information storage and retrieval systems, for any purpose
without the express written permission of Sun Hydraulics Corporation,
1500 West University Parkway, Sarasota, Florida, 34243, USA.
Printed in England
2 1
Pilot Operated, Balanced Piston 6
2 1 Direct Acting 7
2 1
Pilot Operated, Balanced Poppet 9
2 1
Pilot Operated, Balanced Poppet, Soft Start 10
2 1
Pilot Operated, Kick-down 11
Air Pilot
2 1
Electro-proportional Pilot 13
T-8A
Cav
Balanced Piston, Modulating Element with
2 1 Integral Pilot Control Cavity 14
T-8A
Cav
3
2 1
Ventable, Pilot Operated, Balanced Piston 16
3
2 1
Ventable, Pilot Operated, Balanced Poppet 18
bar
250 250
bar
250
bar
bar
4000
PP==psi
PP==psi
PP= =psi
= =psi
100
2000 100
2000 100
2000 2000
100 2000
100
50 50 50 50
1000 50
1000 1000 1000 1000
0 25 50 75 100 0 50 100 150 200 0 100 200 300 400 0 200 400 600 800 0 400 800 1200 1600
0 40
0 5Q=10
L/min.
15 20 25 0
Q =20L/min.
10 30 40 50 0 20
Q =40L/min.
60 80 100 Q =80 120
L/min. 160 200 0 80 160 240
Q = L/min.
320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Maximum operating pressure = 350 bar
■ Maximum operating pressure = 5000 psi
■
■
Will accept maximum pressure at Port 2
Will accept maximum pressure at Port 2.
■
■ Back pressure
Back pressure on
on the
the tank
tank port
port (port
(port 2)
2) is
is directly
directly additive
additive at
at aa 1:1
1:1 ratio
ratio to
to the
the valve
valve setting.
setting
■
■ Factory pressure settings established at
Factory pressure settings established at 4 GPM15 L/min.
■
■ Typical response
Typical response time
time 1010 ms.
ms.
■
■ Maximum leakage = RPCC,
Maximum leakage = RPCC, RPEC: RPEC: 232,8 cc/min./70 psi,
in 3/min./1000 bar, RPGC:
RPGC: 349,2 cc/min./70 psi,
in3/min./1000 bar, RPIC:
RPIC: 466,5
cc/min./70
in bar,psi,
3/min./1000 RPKC:RPKC:81,9 cc/min./70
5 in 3/min./1000 barpsi.
■
■ RPCC minimum setting for all spring ranges is 75 5 bar.
psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 45 L/min.* L Standard Screw A 7 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 95 L/min. C Tamper Resistant B 3,5 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 200 L/min. K Handknob C 10 - 420 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 380 L/min. N 4 - 55 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
K 760 L/min. Q 4 - 25 bar
W 150 - 4500 psi +$ 0.00
W 10 - 315 bar
Adjustment Range Options:
A, B, C, andRange
Adjustment W are Options:
standard set at 1000 psi.
NA,Option is standard
B, C, and set at 400
W are standard set psi.
at 70 bar.
Q Option is
N Option is standard
standard set
set at
at 200 psi.
25 bar.
** See page 162 for information *QMinimum
Option is setting
standard75set
psiaton14allbar.
ranges.
** on
SeeControl Options
page 162 for information Customer
* Minimummay specify
setting 5 barpressure setting.
on all ranges. +$ 1.10
on Control Options Customer may specify pressure setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
b cc
b
Locating
Shoulder Cartridge Dimensions
Locating Cartridge Dimensionsc
Shoulder Typical Installation
Capacity TypicalCartridge Cavity a b c Torque
Installation
Capacity Model Code Cavity
Cartridge a b L C (Nm)
Torque
Model Code L C K (lb. ft.)
45 L/min. RDBA – LAN T - 162A 31 19,1 54 56 35/40
aa 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
95 L/min. RDDA – LAN T - 10A 39,7 22,2 61 63 40/50
22 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Outlet 200 L/min. RDFA – LAN T - 3A 47,8 28,6 64 66 60/70
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
380 L/min. RDHA – LAN T - 16A 61,9 31,8 83 85 200/215
Inlet 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 760 L/min. RDJA – LAN T - 18A 79,4 41,3 100 104 465/500
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RDBA RDDA RDFA RDHA RDJA
RPCC RPEC RPGC RPIC RPKC
Typical Pressure Rise
350
Typical
350
Pressure Rise 350 350
350
300 300 300 300
5000 300
5000
5000 5000 5000
= bar
250
bar
bar
= bar
250 4000
4000 4000 4000
PP==psi
200 200
P =Ppsi
200
= psi
P psi
==
150
3000 3000
150 150
3000 3000
150 150
3000
PP
PP
P=
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
RD ✱ C
A – ✱ ✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control** Adjustment Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 45 L/min. L Standard Screw A 35 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
D 95 L/min. C Tamper Resistant B 20 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
F 200 L/min. C 70 - 420 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
H 380 L/min. D 14 - 55 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 760 L/min. E 7 - 25 bar
W
S 150
3,5 -- 14
4500
barpsi +$ 0.00
W 70 - 315 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
NAdjustment
Option is Range
standardOptions:
set at 400 psi.
QA, Option
B, C, and W are standard
is standard set psi.
set at 200 at 70 bar.
** See page 162 for information *DMinimum
Option is setting
standard75set
psiaton25allbar.
ranges.
on Control Options E Option ismay
Customer standard set pressure
specify at 14 bar.setting. +$ 1.10
U.S. Patent #4,742,846 ** See page 162 for information S Option is standard set at 7 bar.
European Patent Pending on Control Options Customer may specify pressure setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
UK Shortcut Catalogue #999-901-244 7
Relief Valves
PILOT OPERATED, BALANCED PISTON
Relief Valves5 Turns
Full Adjustment
+ -
DIRECT ACTING, PILOT STAGE
Full Adjustment 5 Turns 2 1
+ - c
b 2 1
Locating
Shoulder
c Cartridge Dimensions
Typical c Installation
b Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a Locating 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Cartridge Dimensions
2 Shoulder
25 GPM RPEC Typical
– LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet c Installation
50Capacity
GPM RPGCCartridge
– LAN Cavity
T - 3A 1.88a b
1 1/8” 2.12
L 2.18
C K 2.38
Torque
45/50
Model Code (Nm)
a 100 GPM
1 L/min. RPIC – LAN
RBAC – LAN T - T16A
- 10A 2.44
39,7 1 1/4”
22,2 2.44
51 2.47
53 582.69 150/160
40/50
Inlet 1
2 200 GPM
2 L/min. RPKC – LAN
RBAA – LAN
T - T18A
- 3A 3.13
47,8 1 5/8”
28,6 2.81
54 2.94
56 613.06 350/375
60/70
Outlet
Performance Curves
RPCC Inlet 1 RPEC RPGC RPIC RPKC
Typical Pressure Rise
Performance
5000 Curves 5000 5000 5000 5000
4000 4000 4000 4000
RBAC RBAA
P = psi
4000
P = psi
P = psi
P = psi
P = psi
200 200
150 150
■ Maximum operating pressure = 5000 psi 100 100
50 50
■ Will accept maximum
0
pressure at Port 2. 0 0,5 1,0 1,5 2,0 2,5
0,32 0,64 0,96 1,28 1,6
■ Back pressure on the tank = L/min.(port 2) is directlyFlow
Flow port = L/min. at a 1:1 ratio to the valve setting.
additive
■
■ Factory pressure
Maximum settings
operating established
pressure = 350 barat 4 GPM
■
■ Typical response time 210ms. ms.
■
■ Maximum leakage less= RPCC,than 0,4RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
cc/min.
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RB
RP A
✱✱C – ✱ ✱✱
Nominal
Control** Adjustment Range Seal
Capacity
C 112L/min.
GPM* $ 31.90 L Standard Screw +$ 0.00 A 2100
- 210 bar psi
- 3000 +$ 0.00 N Buna-N +$ 0.00
A
E 225L/min.
GPM $ 36.20 C Tamper Resistant +$ 4.10 B 250- -105 barpsi
1500 +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 2150
- 420 bar psi
- 6000 +$ 2.00
I 100 GPM $ 97.30 D
N 260- -55800
barpsi +$ 1.00
K 200 GPM $187.00 E
Q 260- -25400
barpsi +$ 1.00
W 2 - 315 bar
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
P = psi
P = psi
P = psi
■
■ Maximum operating
Maximum operating pressure
pressure = = 5000
350 barpsi
Will accept maximum pressure at reseat
Maximum leakage 0,7 cc/min. at
■
■ Port 2.
■
■ Reseatpressure
Back exceedson90%
the of
tankcracking pressure.
port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure
Factory pressure settings
settings established
established at
at 415GPML/min.
■
■ Typical response time 10 ms.
■
■ Back pressure
Maximum on the
leakage tank port
= RPCC, (port 22)inis3/min./1000
RPEC: directly additive at a 1:13 ratio
psi, RPGC: to the valve
in3/min./1000 psi,setting
RPIC: 4
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ C
S – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
G 200 L/min. C Tamper Resistant A 7 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper
Factory Resistant
Set +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
I
G 380GPM
50 L/min. $ 51.80 K Handknob +$ 5.00 B 150
C 3,5 -- 105
6000bar
psi +$ 2.00 V Viton
K Handknob
I 100 GPM $ 97.30 N
C 60
10 -- 800
420 psi
bar +$ 1.00
K 200 GPM $187.00 L Standard Screw Q 60 - 400 psi +$ 1.00
Adjustment N 4 - 55 bar
W 150 - 4500 psi +$ 0.00
Q 4 - 25 bar
Adjustment Range Options:
W 7 - 315 bar
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Adjustment
Q Option is Range
standardOptions:
set at 200 psi.
** See page 162 for information A, B, C, setting
* Minimum and W are standard
75 psi set at 70 bar.
on all ranges.
on Control Options N Option
Customer may is standard set at 25 setting.
specify pressure bar. +$ 1.10
** See page 162 for information Q Option is standard set at 14 bar.
on Control Options Customer may specify pressure setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
2 1
c
b c
b
Locating
Shoulder Cartridge Dimensions
Locating Cartridge Dimensions
Shoulder Typical c Installation
Capacity TypicalCartridge Cavity a b c Installation
Torque
Capacity Cartridge
Model Code Cavity a b L C Torque
(Nm)
Model Code L C K (lb. ft.)
a a 200 l/min.
12 GPM RPCC – LAN
RPGT - LANT - 162AT - 3A1.22 47,8
3/4”
28,6
2.11
85,8
2.17
88,1
2.31
60/70
25/30
2
2
Outlet
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Inlet 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
RPCC RPEC RPGC
RPGT RPIC RPKC
Typical PressureTypical Typical
Rise Pressure RiseRamp Time
400 350
5000 5000 350 5000 300 5000 5000
300
P = bar
4000 4000
P = psi
4000
P = psi
P = psi
250
P = psi
P = psi
0 5 10 15 20 25 0 10 0
20 3050 40 10050 150 200
0 20 400 60200 400100 600
80 800 0 100040 80 120 160 200 0 80 160 240 320 400
Flow = GPM Q = L/min.
Flow = GPM Flow = GPM Time/ms. Flow = GPM Flow = GPM
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP G
✱TC – ✱ ✱ ✱
Nominal
Control** Adjustment Range Seal
Nominal
Capacity
Control** Adjustment Range Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
G 200 L/min. C Tamper Resistant A 140 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
Factory Set
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 315
C 150 -- 420
6000bar
psi +$ 2.00 V Viton
I 100 GPM $ 97.30 L Standard Screw N 60 - 800 psi +$ 1.00
K 200 GPM $187.00
Adjustment W 210-315 bar
Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
PerformanceRQEB
Curves RQGB RQIB RQKB
RPCC RPEC Unloaded Pressure Drop RPIC
RPGC RPKC
20 20 20 20
15 15
Typical Pressure15Rise 15
P = bar
P = bar
P = bar
P = bar
C&W
C&W
5000 5000 5000 10 5000 10 5000
10 10
A A
C&W 4000 4000 4000 4000
P = psi
4000
P = psi
C&
P = psi
P = psi
P = psi
A A 5 B, N, Q 5 B, N, Q
5 5
3000 B, N, Q 3000 3000 3000 3000
2000 2000
2000 0 25 50 2000 75 100 0 50 1002000 150 200 0 100 200 300 400 0 200 400 600 800
1000 Q = L/min.
1000 Q = L/min.
1000 Q = L/min.
1000 Q = L/min.
1000
■
■ Maximum
Will acceptoperating
maximum pressure = at
pressure 5000
Portpsi
2.
■
■ Will accept maximum pressure at Port 2.
Flow through cartridge must cease to reset valve.
■
■ Back
Back pressure
pressure on
on the
the tank
tank port
port (port
(port 2)
2) is
is directly
directly additive
additive at
at aa 1:1
1:1 ratio
ratio to
to the
the valve
valve setting.
setting
■
■ Factory pressure settings established at 4 GPM
Factory pressure settings established at kick down point.
■ Typical response time 10 ms.
■ Typical response time 25 ms.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Maximum
in leakage
3/min./1000 = RQEB:
psi, RPKC: 5 in32,8 cc/min./70
3/min./1000 psi.bar, RQGB: 49,2 cc/min./70 bar, RQIB:
65,5 cc/min./70 bar, RQKB: 81,9 cc/min./70 bar
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱C
RQ ✱ B –– ✱
✱ ✱
✱✱✱
Nominal
Capacity Control** Adjustment Range Seal
Nominal
Control** Adjustment Range Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E
E 25
95 GPM
L/min. $ 36.20 C
L Tamper Screw +$ 4.10
StandardResistant B
A 50
7 --210
1500
barpsi +$ 0.00 V Buna-N +$ 2.00
N Viton
G
G 50 L/min. $ 51.80
200GPM K Tamper Resistant +$ 5.00
C Handknob C
B 150
3,5 -- 105
6000bar
psi +$ 2.00 V Viton
II 100 L/min. $ 97.30
380 GPM K Handknob N
C 60
10-- 800
420psi
bar +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
K 760 L/min. N 4 - 55 bar
W
Q 150 - 4500
4 - 25 bar psi +$ 0.00
W 10 - 315 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information *Adjustment Range Options:
Minimum setting 75 psi on all ranges.
on Control Options Customer may
A, B, C, and specify
W are pressure
standard set atsetting.
70 bar. +$ 1.10
N Option is standard set at 25 bar.
** See page 162 for information Q Option is standard set at 14 bar.
on Control Options Customer may specify pressure setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Locating 2 1
Shoulder
c
b Cartridge Dimensions
Typical c Installation
Locating Capacity Cartridge Cavity a b Torque
a Shoulder Model Code A B (Nm)
Cartridge Dimensions
2 200 L/min. RPGD – ABN
Typical T - 3A 47,8 28,6 34 -c 60/70 Installation
Outlet Capacity Cartridge Cavity a61,9 b Torque
380 L/min. RPID
Model Code– BBN T - 16A 31,8 L
- 42C K
200/215 (lb. ft.)
a 760GPM
12 L/min. RPKD
RPCC – BBN T - T162A
– LAN - 18A 79.4
1.22 41,3
3/4” -
2.11 51
2.17 465/500
2.31 25/30
2 Inlet RPEC – LAN
1 25 GPM T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Performance
Inlet 1Curves
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
RPGD RPID RPKD
Performance Curves
Typical Pressure Rise
RPCC RPEC
200
RPGC
200
RPIC
200
RPKC
150 Typical
150 Pressure Rise 150
P = psiP = bar
P = psi P = bar
P = bar
4000 50
P = psi
P = psi
■
■ Will acceptoperating
Maximum maximumpressure
pressure=at5000
Portpsi
2.
■
■ Will acceptair
Maximum maximum
pressure pressure at Port
should not 2. 10 bar.
exceed
■
■ Backratio,
Pilot pressure onhydraulic
air to the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
= 1:20
■
■ Factory response
Typical pressure settings established at 4 GPM
time 10 ms.
■
■ Typical response time
Maximum leakage = RPGD: 10 ms.49,2 cc/min./70 bar, RPID: 65,5 cc/min./70 bar, RPKD: 81,9 cc/min./70
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
bar.
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
C – ✱ ✱ ✱
RP ✱ D
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
G 200 L/min. Available for RPGD only B 3,5 - 105 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
IG 380 L/min. $ 51.80
50 GPM A
K 1/4" NPTF
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
Pilot Port at
I
K GPM $ 97.30
100 L/min.
760 end of Cartridge* N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Available for RPID, RPKD only
W 150 - 4500 psi +$ 0.00
B SAE-4
Pilot Port at
end of Cartridge* Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
* Maximum air pilot pressure N Option is standard set at 400 psi.
should not exceed 10 bar. Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com
Visit www.sunhydraulics.com for
for detailed
detailed and
and complete
complete technical
technical information
information on
on our
our full
full line
line of
of products.
products.
6 US Shortcut Catalogue #999-901-243
P = bar
200 200
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP AC
RB ✱ P – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 1 L/min. M Manual Override A 20 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
(Standard) B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 B
C 10 - -105
150 barpsi
6000 +$ 2.00 V Viton
NOTE: Coil must be
I 100 GPM $ 97.30 ordered separately. Use N
W 60
35 - 800
350 psi
bar +$ 1.00
K 200 GPM $187.00 12V DC or 24V DC Q 60 - 400 psi +$ 1.00
(Series 770-***) coils
only. See page 167. W 150 - 4500 psi +$ 0.00
P = bar
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ C – ✱
8 ✱✱
Nominal Control MinimumControl
Capacity Control** Adjustment Range Seal
Capacity Pressure
C
E 1295 GPM*
L/min. $ 31.90 L
8 Standard Screw
T-8A Cavity in +$ 0.00 A
D 100 - 3000 psi +$ 0.00
1,7 bar N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 hex body for
C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 200 L/min. pilot operation W 7 bar V Viton
G 50 GPM $ 51.80 K Handknob
(Pilot valve to +$ 5.00 C 150 - 6000 psi +$ 2.00
I 380 L/min. be ordered
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
separately)
K L/min. $187.00
760 GPM
200 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Relief Valves
BALANCED POPPET, MODULATING ELEMENT WITH INTEGRAL
PILOT CONTROL CAVITY
T-8A The -8 control option allows a pilot control valve to be incorporated directly
Relief Valves Cav
into the end of the modulating element via the T-8A cavity. These pilot control
cartridges are sold separately and include electro-proportional, solenoid, air
PILOT OPERATED,2 BALANCED
1 PISTON
pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
b
c
Full Adjustment 5 Turns
+ - Locating
Shoulder
2 1
ac Cartridge Dimensions
2 Typical Installation
b
Outlet Capacity Cartridge Cavity a b c Torque
Model Code (Nm)
Locating
Shoulder 200 L/min. RPGS – 8WN T - 3A 84,7 28,6 22,2 60/70
Cartridge Dimensions
Inlet 1 380 L/min. RPIS – 8WN
Typical T - 16A 84,7 31,8 31,8 c 200/215
Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Performance Curves 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN
RPGS-8 RPIS-8 2.44
T - 16A 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Typical Pressure Rise
Performance Curves 250 250
150 150
100 Typical Pressure
100
Rise
50 50
5000 5000 5000 5000 5000
4000 0 50 1004000 150 200 0 100 4000 300
200 400 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
RP ✱SC –
– ✱ ✱✱
8 ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range
MinimumControl Seal
Seal
Capacity Pressure
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
G 200 L/min. 8 T-8A Cavity in B 3,5 bar N Buna-N
E 25 GPM $ 36.20 C hex
Tamper
bodyResistant
for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
IG 380 L/min. $ 51.80
50 GPM K pilot operation
Handknob +$ 5.00 W
C 7150
bar- 6000 psi +$ 2.00 V Viton
(Pilot valve to
I 100 GPM $ 97.30 be ordered N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 separately) Q 60 - 400 psi +$ 1.00
b c
2 1
c
3b Cartridge Dimensions
Vent Locating Typical c Installation
Shoulder Capacity Cartridge Cavity a b Torque
Locating Model Code L C K (Nm)
Shoulder
30 L/min.RVBA – LAN T - 163A 31 Cartridge 65
19,1 Dimensions
67 71 35/40
a Typical c Installation
2 60 L/min.
Capacity RVCA – LAN
Cartridge T - 11A
Cavity a 34,9 22,2
b 64 66 70 40/50
Torque
L C K
Outlet 120 L/min. Model Code
RVEA – LAN T - 2A 34,9 28,6 72 74 78 (lb. ft.)
60/70
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
240 L/min. RVGA – LAN T - 17A 46 31,8 84 86 90 200/215
2 Inlet 1 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 480 L/min. RVIA – LAN T - 19A 63,5 41,3 100 104 107 465/500
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance Curves 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
RVBA RVCA200 GPM RVEA T - 18A
RPKC – LAN 3.13 RVGA
1 5/8” 2.81 RVIA
2.94 3.06 350/375
250
P = bar
P = bar
250
P = bar
P = bar
200
Typical Pressure Rise
200 200 200 200
150 150 150 150 150
100 100 100 100 100
5000 5000 5000 5000 5000
50 50 50 50 50
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
0 12,5 25 37,5 50 0 25 50 75 100 0 50 100 150 200 0 100 200 300 400 0 200 400 600 800
3000 Q = L/min. 3000 Q = L/min. 3000 Q = L/min. 3000
Q = L/min. 3000
Q = L/min.
2000 2000 2000 2000 2000
1000
■ Maximum
1000 operating pressure1000= 350 bar 1000 1000
0 5 10 15 20
■
25 Pressure
0 at port
10 20 3 (vent)
30 40 50 controls0 the
20 valve
40 below
60 its setting.
80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Maximum
Control operating
pilot pressureRVCA:
flow = RVBA, = 50000,11psi L/min. to 0,16 L/min.; RVEA: 0,16 L/min. to 0,25 L/min.;
■ Will accept maximum pressure
RVGA, RVIA: 0,25 L/min. to 0,33 L/min. at Port 2.
■
■ Back pressure
Factory pressure onsetting
the tank port (port at
established 2)15is L/min.
directly additive at a 1:1 ratio to the valve setting.
■
■ Factory response
Typical pressure settings
time 10 established
ms. at 4 GPM
■
■ Typical response
Maximum leakagetime 10 ms.RVCA: 32,8 cc/min/70 bar, RVEA: 49,2 cc/min/70 bar, RVGA:
= RVBA,
■ 65,5
Maximumcc/min/70
leakagebar, =RVIA:
RPCC, 81,9
RPEC:cc/min/70 bar.
2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ in3/min./1000
RVBA minimum psi,setting
RPKC:for all3/min./1000
5 in spring ranges psi.is 5 bar.
■
■ RPCC
Will minimum
accept maximum setting for all spring
pressure at port ranges
2. is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ A
RV C – ✱ ✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity
C
B GPM* $ 31.90
12 L/min.*
30 L Standard
L Standard Screw
Screw +$ 0.00 A 7100
A - 3000
- 210 bar psi +$ 0.00 N Buna-N
N Buna-N +$ 0.00
E
C 25 L/min.
60 GPM $ 36.20 C Tamper
C Resistant +$ 4.10
Tamper Resistant B 3,5
B 50 -- 1500 psi
105 bar +$ 0.00 V Viton
V Viton +$ 2.00
G
E L/min. $ 51.80
50 GPM
120 K Handknob
K Handknob +$ 5.00 C 10
C 150- 420
- 6000
barpsi +$ 2.00
I
G GPM $ 97.30
100 L/min.
240 N 460- -55800
N barpsi +$ 1.00
IK GPM $187.00
200 L/min.
480 Q 460- -25400
Q barpsi +$ 1.00
W 10
150- 315 barpsi
- 4500 +$ 0.00
1
2
b c 2 1
c
b
3 Cartridge Dimensions
Locating
Locating
Vent Shoulder Typical c Installation
Shoulder Capacity Cartridge Cavity a bCartridge Dimensions Torque
Model Code L C K (Nm)
Typical c Installation
Capacity
10 L/min. Cartridge
RVBB – LAN Cavity
T - 163A a 31 b
19,1 65L 67 C 71 K Torque
35/40
a Model Code (lb. ft.)
2 a 20GPM
12 L/min. RVCB
RPCC – LAN T - 162A
– LAN T - 11A 34,9
1.22 22,2
3/4” 64
2.11 662.17 70 2.31 40/50
25/30
2
Outlet 40GPM
25 L/min. RVEB
RPEC – LAN T - 10A
– LAN T - 2A 34,9
1.56 28,6
7/8” 72
2.00 742.06 78 2.25 60/70
30/35
Outlet
80GPM
50 L/min. RVGB
RPGC – LAN T - 3A
– LAN T - 17A 46
1.88 1 31,8
1/8” 84
2.12 862.18 90 2.38 200/215
45/50
Inlet 1
100 L/min. RPIC
160GPM – LAN
RVIB – LAN T - 16A
T - 19A 2.44
63,5 1 41,3
1/4” 2.44
100 1042.47 107 2.69 150/160
465/500
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RVBB RVCB RVEB RVGB RVIB
RPCC RPEC RPGC RPIC RPKC
Typical Compensator Differentials
Typical Pressure Rise
P Differential
P =Differential
P =Differential
P =Differential
Pressure Differential
25 25 25 25 25
Port 1 to 3 (bar)
Port 1 to 3 (bar)
Port 1 to 3 (bar)
Port 1 to 3 (bar)
Port 1 to 3 (bar)
5000 Bypass Flow 5000 Bypass Flow 5000 5000 Bypass Flow 5000 Bypass Flow
240 L/min. 160 L/min.
Port 1 to 2 Port 1 to 2 Port 1 to 2 Port 1 to 2
4000 20 400020 20
4000 20
4000 480 L/min. 20
4000
= psi
psi
P = psi
psi
psi
Pressure
Pressure
Pressure
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱C
RV ✱ B –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
C
Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 10 L/min.* L Standard Screw A 7 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C
G
20 L/min.
50 GPM $ 51.80
C Tamper Resistant +$ 5.00
K Handknob
B 7 - 105 bar**
C 150 - 6000 psi +$ 2.00
V Viton
IE 40 L/min.
100 GPM $ 97.30 K Handknob C 60
N 7 - -420
800bar
psi +$ 1.00
G
K 80 L/min.
200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 160 L/min. W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
3
c
Ventb Cartridge Dimensions
Locating
Shoulder Typical c Installation
Capacity Cartridge Cavity a b Torque
Locating
Shoulder Model Code L C K (Nm)
2 a Cartridge Dimensions
120 l/min.RVES – LAN T - 2A 35,0 28,6 71,0 73,0 78,0 60/70
Outlet Typical c Installation
Capacity
200 l/min. RVGS – LAN
Cartridge Cavity
T - 17A a 46,0 b 31,8 83,3
L 84,1C 89,7 K Torque
200/215
Model Code (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Inlet 1
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
RVES RVGS
Performance CurvesTypical Pressure Rise Vented Pressure Typical Pressure Rise Vented Pressure
RPCC 250
200
RPEC 12,5
10
RPGC 250
200
RPIC 12,5
10
RPKC
P = bar
P = bar
P = bar
P = bar
C, W, A
Typical Pressure Rise
150 7,5 C, W, A 150 7,5
B
100 5 100 5
B 5000 5000
5000 50 5000 2,5 5000 50 2,5
0 4000 0 4000 0 4000 0 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
0 100 200 300 400 0 60 120 180 240 0 100 200 300 400 0 60 120 180 240
3000 3000 3000 3000 3000
Q = L/min. Q = L/min. Q = L/min. Q = L/min.
2000 2000 2000 2000 2000
1000 1000 1000 1000 1000
0 5 10 15 20
■
25
Maximum
0 10
operating
20 30 40
pressure
50
=0 35020 bar.
40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM
Flow = GPM ■ Will acceptFlow = GPM
maximum pressure at port 2
■
■ Maximum
Pressure at operating
port 3 (vent)pressure = 5000
controls psi below its setting.
the valve
Back pressure on the tank port (port 2) 2.
Will accept maximum pressure at Port
■
■ is directly additive at a 1:1 ratio to the valve setting.
■
■ Back pressure
Factory pressure onsetting
the tank port (port at
established 2)15is L/min.
directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Maximum leakage at reseat = 0,7 cc/min.
■ Typical response time 10 ms.
■ Reseat exceeds 90% of crack
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Typical response
in3/min./1000 psi,10 ms 5 in3/min./1000 psi.
RPKC:
■
■ Control pilot flowsetting
RPCC minimum = RVES: for 0,16 L/min.
all spring to 0,25
ranges L/min;
is 75 psi RVGS: 0,25 L/min. to 0,33 L/min
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RV
RP ✱ S
C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Adjustment Range Seal
Seal
Capacity
C
E 12 L/min.
30 GPM* $ 31.90 L Tamper
C Screw +$ 0.00
StandardResistant A 7100
A - 3000
- 210 bar psi +$ 0.00 N Buna-N
N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Factory Resistant +$ 4.10
Tamper Set B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 120 L/min. B 3,5 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
K Handknob
I 100 GPM $ 97.30 C
N 10
60 - 420
800 bar
psi +$ 1.00
L Standard Screw
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Adjustment N 4 - 55 bar
W 150 - 4500 psi +$ 0.00
Q 4 - 25 bar
W
Adjustment
10 - 315 Range
bar Options:
A, B, C, and W are standard set at 1000 psi.
N Option is Range
Adjustment standard set at 400 psi.
Options:
Q Option is standard set at 200 psi.
A, B, C and W are standard set at .70 bar.
** See page 162 for information * Minimum setting 75 psi on all ranges.
N Option is standard set at 25 bar.
on Control Options Customer may specify pressure setting. +$ 1.10
Q option is standard set at 14 bar.
** See page 162 for information
on Control Options Customer may specify pressure settings.
Visit www.sunhydraulics.com
Visit www.sunhydraulics.com for detailed
for detailed and complete
and complete technical
technical information
information onfull
on our ourline
fullofline of products.
products.
6 US Shortcut Catalogue #999-901-243
b 240 L/min. RVGD – LAN T - 23A 46 31,8 100 102 107 200/215
2 a 480 L/min. RVID – LAN T - 24A 63,5 41,3 122 126 129 465/500
Outlet Locating
Shoulder
Cartridge Dimensions
Inlet 1 Typical c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
Performance Curves a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 RVCD 25 GPM RVED
RPEC – LAN RVGD
T - 10A 1.56 7/8” RVID
2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN Vented Pressure
T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
15 15 15 15
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 C&W C&W
P = bar
P = bar
P = bar
P = bar
10 10 10 10
C&W 200 GPM RPKC –C &LAN
W
T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
A A
5 5 5 5
A A B
Performance Curves B
D&E B D&E B
D&E D&E
0 20 40 60 80 0 40 80 120 160 0 100 200 300 400 0 200 400 600 800
RPCC RPEC
Q = L/min. Q =RPGC
L/min. RPIC
Q = L/min. RPKC
Q = L/min.
TypicalPressure
Typical PressureRise
Rise
350 350 350 350
300 5000 300 5000 300 5000 300 5000
5000
P = bar
250 250
P = bar
4000 200
P = psi
200 200
P = psi
P = psi
P = psi
200
3000 150 3000 150 3000 150 3000 150 3000
100 100 100 100
2000 2000 2000 50 2000 2000
50 50 50
1000 1000 1000 1000 1000
0 50 100 150 200 0 100 200 300 400 0 200 400 600 800 0 400 800 1200 1600
Flow = L/min. Flow = L/min. Flow = L/min. 0 40 80 120 Flow
160 200= L/min. 0 80 160 240 320 400
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■
■ Maximumoperating
Maximum operating pressure
pressure = 350= 5000
bar psi
■
■ Will accept
Pressure maximum
at port pressure
4 is directly additiveattoPort 2. setting at a 1:1 ratio and should not exceed 350 bar
the valve
■ Pressure at port 3on(vent) controls
■ Back pressure the tank portthe valve
(port 2)below its setting.
is directly additive at a 1:1 ratio to the valve setting.
■
■ Control pilot flow = RVCD: 0,11 L/min.
Factory pressure settings established at 4 GPMto 0,16 L/min.; RVED: 0,16 L/min. to 0,25 L/min.; RVGD,
RVID: 0,25 L/min. to 0,33 L/min.
■
■
Typical response time 10 ms.
Factory pressure setting established at 15 L/min.
Maximum leakage 3 3
time=10RPCC,
ms. RPEC: 2 in /min./1000 psi, RPGC: 3 in /min./1000 psi, RPIC: 4
■
■ Typical response
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Maximum leakage = RVCD: 32,8 cc/min/70 bar, RVED: 49,2 cc/min/70 bar, RVGD: 65,5 cc/min/70
■ RPCC
bar, minimum
RVID: setting bar.
81,9 cc/min/70 for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RV
RP ✱ D
C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Adjustment Range Seal
Seal
Capacity
C
C 12 L/min.
60 GPM* $ 31.90 L Standard
L Standard Screw
Screw +$ 0.00 A 7100
A - 3000
- 210 bar psi +$ 0.00 N Buna-N
N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. C Tamper Resistant B 3,5 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 240 L/min. K Handknob C 10 - 420 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 480 L/min. D 2 - 55 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
E 2 - 25 bar
W 150 - 4500 psi +$ 0.00
W 10 - 315 bar
Adjustment Range Options:
Adjustment Range Options:
A, B, C, and W are standard set at 70 bar.
A, B, C, and W are standard set at 1000 psi.
D Option
N Option is standard
is standard set400
set at at 25 bar.
psi.
**See page 162 for information E Option
Q Option is standard
is standard set set at 14psi.
at 200 bar.
on
** Control
See pageOptions
162 for information Customer
* Minimummay specify
setting 75 psipressure setting.
on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com
UK Shortcut Catalogue #999-901-244 19
for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Relief Valves
VENTABLE, BALANCED PISTON, MODULATING ELEMENT WITH EXTERNAL
DRAIN AND INTEGRAL PILOT CONTROL ELEMENT
P = bar
P = bar
P = bar
10 10 10 10
C&W 200 GPM RPKC –C &LAN
W
T - 18A 3.13 1 5/8” 2.81
A
2.94 3.06 350/375
A
5 5 5 5
A A B
B
Performance Curves B
D&E B D&E
D&E D&E
0 20 40 60 80 0 40 80 120 160 0 100 200 300 400 0 200 400 600 800
RPCC RPEC
Q = L/min. Q =RPGC
L/min. RPIC
Q = L/min. RPKC
Q = L/min.
Typical Pressure Rise
Typical Pressure Rise
344 344 344 344
5000 5000 5000 5000 5000
300 300 300 300
P = bar
P = bar
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
RV ✱ C
D – ✱
8 ✱✱
Nominal
Nominal
Capacity Control
Control** Minimum Control
Adjustment Range Seal
Seal
Capacity Pressure
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. 8 T-8A Cavity in D 1,7 bar N Buna-N
E 25 GPM $ 36.20 C Tamper
hex bodyResistant
for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 120GPM
50 L/min. $ 51.80 pilot operation
K Handknob +$ 5.00 W 150
C 7 bar- 6000 psi +$ 2.00 V Viton
(Pilot valve to
IG 100 L/min. $ 97.30
240 GPM be ordered N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 separately) Q 60 - 400 psi +$ 1.00
I 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Sequence Cartridge Valves
3
T-8A
Cav
Externally Drained, Balanced Piston,
23
2 1 Modulating Element
Air Pilot
2 1
Direct Acting without Reverse Flow Check 25
22 11
c
b c
b
Locating
3 Shoulder Cartridge Dimensions
Dimensions
Cartridge
Drain Locating Typical cc Installation
Shoulder Typical Installation
Capacity Cartridge Cavity a a bb Torque
Capacity Cartridge
Model Code
Cavity L
L CC K K Torque
(Nm)
Model Code (lb. ft.)
a 1230GPM
L/min. RSBC
RPCC – LAN T - T162A
– LAN - 163A 1.2231 19,1
3/4” 65
2.11 67
2.17 712.31 35/40
25/30
a
22 2560GPM
L/min. RSDC
RPEC – LAN T - T10A
– LAN - 11A 1.5634,9 22,2
7/8” 64
2.00 66
2.06 702.25 40/50
30/35
Outlet
Sequence 120 L/min.
50 GPM RSFC –
RPGC – LANLAN -
T - 3A 2A
T 1.8834,9 1 1/8”
28,6 72
2.12 74
2.18 782.38 60/70
45/50
240 L/min. RSHC –
RPIC – LANLAN - 17A
T - T16A 46 31,8 84 86 902.69 200/215
Inlet 1 100 GPM 2.44 1 1/4” 2.44 2.47 150/160
Inlet 1 480GPM RSJC
L/min. RPKC – LAN T - T18A
- 19A 63,5 41,3 100 104 107 465/500
200 – LAN 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RSBC
RPCC RSDC
RPEC RSFC
RPGC RSHC
RPIC RSJC
RPKC
Pressure Drop
Typical Sequenced
Pressure RiseOpen
14 14 14 14
5000 14
5000
5000 5000 5000
12 12 12 12 12
4000 4000 4000 4000
bar
psi
4000
PP==bar
PP == bar
bar
10
PP == bar
10 10 10
psi
10
psi
PP = psi
P == psi
8
3000 8
3000 8
3000 3000
8 8
3000
6
2000 6
2000
6
2000 6
2000 6
2000
4 4 4 4 4
1000 1000 1000 1000 1000
2 2 2 2 2
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
0 10 20 30 40 0 40 80 120 160 0 80 160 240 320 0 160 320 480 640
Flow = GPM
0 20 40
Flow = GPM
60 80 Flow = GPM Flow = GPM Flow = GPM
Flow = L/min. Flow = L/min. Flow = L/min. Flow = L/min. Flow = L/min.
■
■ Maximum
Maximum operating
operating pressure
pressure == 5000
350 barpsi
■
■ Will acceptleakage
Maximum maximum pressure
= RSDC: 32,8at Port 2.
cc/min./70 bar, RSFC: 49,2 cc/min./70 bar, RSHC: 65,5 cc/min./70
■ bar , RSJC:
Back 81,9
pressure oncc/min./70 bar.(port 2) is directly additive at a 1:1 ratio to the valve setting.
the tank port
■ Typical response
Factory time 10 established
pressure settings ms at 4 GPM
■ Pressureresponse
Typical at port 3time
is directly
10 ms.additive to the valve setting at a 1:1 ratio and should not exceed 350 bar.
■ Pilot flow continues
Maximum leakage = to increase
RPCC, as the
RPEC: 2 in 3/min./1000
pressure at portpsi,
1 (inlet), 3 in3/min./1000
RPGC:relative to the pressure at port
psi, RPIC: 4 3 (drain),
in 3/min./1000
rises above thepsi,
valve 5 in3/min./1000 psi.
setting.
RPKC:
■ RSBC minimum setting for
RPCC is 5all
barspring
for allranges
springisranges.
75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
RS ✱ C – ✱ ✱ ✱
Nominal
Capacity Control** Adjustment Range Seal
C
B 12 L/min.* $ 31.90
30 GPM* L Standard Screw +$ 0.00 A 100 - 3000
7 - 210 bar psi +$ 0.00 N Buna-N +$ 0.00
E
D 25
60 GPM
L/min. $ 36.20 C Tamper Resistant +$ 4.10 B 50
3,5--1500 psi
105 bar +$ 0.00 V Viton +$ 2.00
G
F 50 L/min. $ 51.80
120GPM K Handknob +$ 5.00 C 150
10 - -420
6000
barpsi +$ 2.00
IH 100 L/min. $ 97.30
240 GPM N 60
4 - -55
800
barpsi +$ 1.00
K
J 200 L/min. $187.00
480 GPM Q 60
4 - -25
400
barpsi +$ 1.00
W 150
W 10 - -315 barpsi
4500 +$ 0.00
Visit www.sunhydraulics.com
Visit www.sunhydraulics.com for
for detailed
detailed and
and complete
complete technical
technical information
information on
on our
our full
full line
line of
of products.
products.
6 US Shortcut Catalogue #999-901-243
P = bar
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
0 5 10 15 20 ■ 25 Maximum
0 10 operating
20 30 40pressure
50 =0 35020 bar40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Will accept maximum pressure at Port 2.
■ Maximum operating pressure = 5000 psi
■ Pressure at port 3 is directly additive at a 1:1 ratio to the valve setting and should not exceed 350 bar
■ Will accept maximum pressure at Port 2.
■ Control pilot flow = RSDC-8: 0,11 to 0,16 L/min., RSFC-8: 0,16 to 0,25 L/min., RSHC-8, RSJC-8:
■ Backtopressure
0,25 0,33 L/min.on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Maximum leakage = RSDC-8: 32,8 cc/min/ 70 bar: RSFC-8: 49,2 cc/min./70, RSHC-8: 65,5 cc/min./70
■ Typical
bar, response
RSJC-8: 81,9time 10 ms. bar.
cc/min./70
■
■ Maximum
With the -8 control option, theRPEC:
leakage = RPCC, main stage2 in 3valve
/min./1000
shouldpsi,
firstRPGC: 3 in3/min./1000
be installed psi,
to the correct RPIC:
torque 4
value.
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
The T-8A pilot control valve should then be installed into the main stage valve to its required torque value.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ C – ✱
RS 8 ✱✱
Nominal
Nominal Control MinimumControl
Capacity Control** Adjustment Range Seal
Seal
Capacity Pressure
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. 8 T-8A Cavity in D 1,7 bar N Buna-N
E 25 GPM $ 36.20 C hex bodyResistant
Tamper for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 120 L/min. pilot operation W 7 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
(Pilot valve to
I
H GPM $ 97.30
100 L/min.
240 be ordered N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 separately) Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit
Visit www.sunhydraulics.com
www.sunhydraulics.com for
for detailed
detailed and
and complete
complete technical
technical information
information on
on our
our full
full line
line of
of products.
products.
6 US Shortcut Catalogue #999-901-243
3
2 1
b 2 1
c
c
b
3 Locating
Shoulder
Locating
Drain Cartridge
Cartridge Dimensions
Dimensions
Shoulder
Typical
Typical c c Installation
Installation
Capacity
Capacity Cartridge
Cartridge Cavity Cavity a a b b Torque
Torque
ModelModel
Code Code L A C B K (lb. ft.)
aa (Nm)
12
120 L/min. RPCC
GPM – LAN
RSFE – ABN
T - 162A
T - 2A 1.22 34,9 3/4” 28,6 2.11 51 2.17 - 2.31 25/30
60/70
22 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Sequence 240 L/min. RSHE – BBN T - 17A 46 31,8 - 63 200/215
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
480 L/min. RSJE – BBN T - 19A 63,5 41,3 - 80 465/500
Inlet 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC RPEC RPGC RPIC RPKC
RSFE RSHE RSJE
Typical Pressure Rise
5000 5000
Pressure
5000
Drop Sequenced Open 5000 5000
14
4000 4000
27 4000
27 4000
P = psi
4000
= psi
P = psi
P = psi
= psi
12
3000 3000 3000 3000
21 3000
10 21
bar
P = bar
bar
2000 8
2000 2000 2000 2000
P=P
P =P
14 14
1000 6
1000 1000 1000 1000
4 7 7
0 5 10 15 20 25 2 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
0 40 80 120 160 0 100 200 300 400 0 200 400 600 800
Q = L/min.
■ MaximumQ operating
= L/min.
pressure = 5000Qpsi= L/min.
■
■ Will accept
Pilot maximum
ratio, air pressure
to hydraulic 1:20 at Port 2.
■
■ Maximum operating pressure =(port
Back pressure on the tank port 2) is directly additive at a 1:1 ratio to the valve setting.
140 bar
■
■ Factory pressure settings established
Maximum air pressure should not exceed at 4 GPM
10 bar.
■
■ Typical response
Typical response timetime 10
10 ms.
ms.
■
■ Maximum leakage
Maximum leakage = = RSFE:
RPCC, 49,2
RPEC: 2 in 3/min./1000
cc/min./70 psi, 65,5
bar, RSHE: RPGC: 3 in3/min./1000
cc/min./70 bar, psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in 3/min./1000 psi.
RSJE: 81,9 cc/min./70 bar.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ E
RS C – ✱ B
✱✱
Nominal
Nominal
Capacity Control**
Control Adjustment Range
Adjustment Range Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
F 120 L/min. Available for RSFE only B 3,5 - 105 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
H
G 240 L/min. $ 51.80
50 GPM A
K 1/4" NPTF
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
Pilot Port at
JI GPM $ 97.30
100 L/min.
480 end of Cartridge* N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Performance 1
Inlet Curves
4000
P = psi
P = psi
P = psi
P = psi
20
P = bar
0 5 10 15 20 25 0 10 20 1430 40 50 0 20 40 14
60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
7 7
■ Maximum operating pressure = 5000 psi
0 20 40 60 0 40 80 120
■ Will accept maximum Q pressure
= L/min. at Port 2. Q = L/min.
■
■ Back pressure
Maximum on the pressure
operating tank port=(port
350 2)
baris directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure settings established
Maximum valve leakage at reseat = 0,7 at 4cc/min
GPM
■
■ Typical response time 10
Typical response time 2 ms ms.
Maximum 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
Pressure atleakage
port 3 is=directly
RPCC, additive
RPEC: 2tointhe
■
■ valve setting at a 1:1 ratio and should not exceed 350 bar.
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Reseat exceeds 85% of cracking pressure.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
SX ✱ C
A – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C
C 1260 GPM*
L/min. $ 31.90 L
L Standard Screw +$ 0.00
Standard Screw A
A 100
35 - -210
3000
barpsi +$ 0.00 N Buna-N +$ 0.00
N Buna-N
E
E 25 L/min. $ 36.20
120GPM C
C Tamper Resistant +$ 4.10
Tamper Resistant B 50 - 1500 psi
B 20 - 105 bar +$ 0.00 V Viton
V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C
C 150
140 -- 6000 psi
420 bar +$ 2.00
I 100 GPM $ 97.30 N
D 60
14 -- 800 psi
55 bar +$ 1.00
K 200 GPM $187.00 Q
W 60
55 -- 400
315 psi
bar +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000 12 12 12
P = psi
12
P = psi
P = psi
P = psi
0 5 10 0
15 2015 25 30 45
0 60
10 20 0
30 4030 50 60 90
0 120 40
20 600 8060100 120 180
0 240
40 80 1200 160120
200 240 0360 80480 160 240 320 400
Flow = GPM Flow = L/min. Flow = GPM Flow = L/min. Flow = GPM Flow = L/min. Flow = GPM Flow = L/min. Flow = GPM
■
■ Maximum
Maximum operating
operating pressure
pressure == 5000
350 barpsi
■
■ Will
Maximum valve leakage at reseat = 0,72.cc/min
accept maximum pressure at Port
■
■ Back pressure
Free flow checkoncracking
the tank pressure
port (port= 2)
2,8isbar
directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure settings
Typical response time 2 ms established at 4 GPM
■
■ Typical response time 10 ms.additive to the valve setting at a 1:1 ratio and should not exceed 350 bar.
Pressure at port 3 is directly
■
■ Maximum
Reseat leakage = RPCC,
exceeds 85% of cracking RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
pressure.
3 3
in /min./1000 psi, RPKC: 5 in /min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
SC ✱ C
A – ✱ ✱✱
Nominal
Capacity Control** Adjustment Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. L Standard Screw A 35 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. C Tamper Resistant B 20 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 240 L/min. C 140 - 420 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 480 L/min. D 14 - 55 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 55 - 315 bar
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
26 UK Shortcut Catalogue #999-901-244
Sequence Valves
PILOT
Relief OPERATED, KICK-DOWN
Valves
PILOT OPERATED, BALANCED PISTON
Full Adjustment 5 Turns
+
Full Adjustment -5 Turns 3
+ -
2 1
2 1
b cc
b
3 Locating Cartridge Dimensions
Drain Shoulder
Locating Typical c
Cartridge Dimensions Installation
Shoulder Capacity Cartridge Cavity a b Torque
Typical L Cc K Installation
Capacity Model Code
Cartridge Cavity a b (Nm)
Torque
Model Code L C K (lb. ft.)
aa 60 L/min. SQDB – LAN T - 11A 34,9 22,2 64 66 70 40/50
2 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
120 L/min. SQFB – LAN T - 2A 34,9 28,6 72 74 78 60/70
2
Sequence 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 240 L/min. SQHB – LAN T - 17A 46 31,8 84 86 90 200/215
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Inlet 1 480 L/min. SQJB – LAN T - 19A 63,5 41,3 100 104 107 465/500
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance
Performance Curves
Curves
RPCC SQDB RPEC SQFB RPGC SQHB RPIC SQJB RPKC
Pressure Drop
Typical Sequenced
Pressure RiseOpen
10 10 20 20
5000 5000 5000 5000 5000
8 8 16 C&W
16
C&W
P = bar
P = bar
P = bar
4000 6
P = psi
12 12
P = psi
6
P = psi
P = psi
C&W C&W
3000 3000 3000 3000 A 3000B
4 8 A 8
A A B
2000 B 2000 2000 2000 2000
2 2 B 4 4
D&E 1000 1000
1000 1000 D&E 1000 D&E D&E
■
■ Maximum operating pressure = 350 5000bar
psi
■
■ Will accept maximum pressure at
Maximum leakage = SQDB: 32,8 cc/min./70 Port 2. bar, SQFB: 49,2 cc/min./70 bar , SQHB:
■ 65,5
Backcc/min./70
pressure on bar,
theSQJB: 81,9(port
tank port cc/min./70 bar additive at a 1:1 ratio to the valve setting.
2) is directly
■
■ Typical
Factory response time 25 ms
pressure settings established at 4 GPM
■
■ Pressure at port 3 time
Typical response is directly
10 ms.additive to the valve setting at a 1:1 ratio and should not exceed 350 bar.
■
■ Maximum
To leakage
reset valve, flow=through
RPCC, theRPEC: 2 in 3/min./1000
cartridge must cease.psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ B
SQ C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. L Standard Screw A 7 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 120 L/min. C Tamper Resistant B 3,5 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
H 240 L/min. K Handknob C 10 - 420 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
J 480 L/min. D 2 - 55 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
E 2 - 25 bar
W 150 - 4500 psi +$ 0.00
W 10 - 315 bar
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4
Pilot Operated Reducing/Relieving, Externally
33
3
2 1
Drained
4
3
Pilot Operated Reducing/Relieving, Ventable 34
2 1
Air Pilot
Air Pilot
3
T-8A
Cav
Modulating Element with Integral Pilot
37
2 1 Control Cavity
T-8A
3
Cav
3-Way, Modulating Element with Integral
38
2 1
Pilot Control Cavity
3
4
T-8A
Cav 3-Way, Externally Drained, Modulating Element
39
2 1
with Integral Pilot Control Cavity
b c Locating
Shoulder
Cartridge Dimensions
Typical c Installation
3 Capacity Cartridge Cavity a b Torque
Locating Model Code L
Cartridge Dimensions C K (lb. ft.)
Drain
aShoulder 12Capacity
GPM
Typical
RPCCCartridge
– LAN
T - 162A 1.22a 3/4” 2.11
c
2.17 2.31
Installation
25/30
Cavity b Torque
2 Model Code L C K (Nm)
25 GPM RPEC – LAN
T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet PBBB – LAN
T - 163A
a 20 L/min.
RPGC – LAN
31 19,1 65 67 71 35/40
2 50 GPM T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Inlet 40 L/min.
100 GPM PBDB
RPIC – LAN – LAN
T - 11A
T - 16A
34,9
2.44
22,2
1 1/4”
64
2.44
66
2.47
70
2.69
40/50
150/160
Inlet 1 80 GPM
L/min. PBFB – LAN T - 2A 34,9 28,6 72 74 783.06 60/70
200 RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 350/375
1 160 L/min. PBHB – LAN T - 17A 46 31,8 84 86 90 200/215
ReducedCurves
Performance Pressure
320 L/min. PBJB – LAN T - 19A 63,5 41,3 100 104 107 465/500
RPCC RPEC RPGC RPIC RPKC
Performance Curves
Typical Pressure Rise
PB*B PBDB PBFB PBHB
5000
PBJB
5000 5000 5000 5000
4000 Regulated Pressure
4000 4000 4000
P = bar P = psi
4000
P = bar P = psi
P = barP = psi
P = barP = psi
P = barP = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ B
PB C – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Adjustment Range Seal
Seal
Capacity
C
B GPM* $ 31.90
12 L/min.*
20 L Standard
L Standard Screw
Screw +$ 0.00 A 7100
A - 3000
- 210 bar psi +$ 0.00 N Buna-N
N Buna-N +$ 0.00
E
D 25 L/min.
40 GPM $ 36.20 C Tamper
C Resistant +$ 4.10
Tamper Resistant B 3,5
B 50 -- 1500 psi
105 bar +$ 0.00 V Viton
V Viton +$ 2.00
G
F 50 L/min.
80 GPM $ 51.80 K Handknob
K Handknob +$ 5.00 C 4150
N - 55- 6000
bar psi +$ 2.00
I
H GPM $ 97.30
100 L/min.
160 N 460- -25800
Q barpsi +$ 1.00
JK GPM $187.00
200 L/min.
320 Q 10
W 60 -- 315
400 bar
psi +$ 1.00
Adjustment Range
Adjustment Range Options:
Options:
A, B,
All areC,standard
and W aresetstandard
at 14 bar.set at 1000 psi.
N Option ispressure
Maximum standard set at 400 psi.
differentials for spring ranges:
Q Option
A and B is are
standard set at 200 psi.
210 bar.
** See page 162 for information * Minimum
N and Q setting
are 14075 psi on all ranges.
bar.
on Control Options Customer
W is 350may bar specify pressure setting.
inlet pressure. +$ 1.10
** See page 162 for information * Minimum setting 5 bar on all ranges.
on Control Options Customer may specify pressure setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c 2 1
bb c
Locating
Shoulder
3
Cartridge Dimensions
Locating Typical Cartridge Dimensions c Installation
Tank
Shoulder Capacity Typical
Cartridge Cavity a b c Installation
Torque
Capacity ModelCartridge
Code Cavity a b L C K Torque
(lb. ft.)
a Model Code L C K (Nm)
12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
22 a 40 L/min. PPDB – LAN T - 11A 34,9 22,2 64 66 70 40/50
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Inlet 80 L/min. PPFB – LAN T - 2A 34,9 28,6 72 74 78 60/70
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
160 L/min. PPHB – LAN T - 17A 46 31,8 84 86 90 200/215
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 11 320 L/min. PPJB – LAN T - 19A 63,5 41,3 100 104 107 465/500
Reduced Pressure 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC RPEC RPGC RPIC RPKC
PPDB PPFB PPHB PPJB
Typical Pressure Rise
5000 5000
Regulated Pressure
5000 5000 5000
Relieving Reducing
4000 Relieving Reducing
4000 Relieving 4000
Reducing Relieving Reducing
4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
2000 100 2000 100 2000 100 2000 P = bar 100 2000
80 80 80 1000
80
1000 1000 1000 1000
60 60 60 60
0 5 10 40
15 20 25 0 10 20 40
30 40 50 0 20 40 40
60 80 100 0 40 80 40
120 160 200 0 80 160 240 320 400
Flow =
20
GPM
20
Flow = GPM Flow = 20
GPM Flow = GPM
20
Flow = GPM
0 0 0 0
-40 -20 0 20 40 60 -80 -40 0 40 80 120 -160 -80 0 80 160 240 -320 -160 0 160 320 480
■ Q= L/min.
Maximum Q = L/min.
operating pressure = 5000 psi Q = L/min. Q = L/min.
■
■ Will accept maximum pressure
Maximum operating pressure = 350 bar at Port 2.
■
■ Back
Factory pressure
pressureonsetting
the tank port (port at
established 2)blocked
is directly additive
control portat(deadhead)
a 1:1 ratio to the valve setting.
■
■
Factory pressure settings established at 4 GPM
Control pilot flow = PPDB: 0,11 to 0,16 L/min., PPFB: 0,16 to 0,25 L/min., PPHB, PPJB: 0,25 to
■ Typical response time 10 ms.
0,33 L/min.
Maximum 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
■ Pressure at leakage
port 3 is=directly
RPCC, additive
RPEC: 2tointhe valve setting at a 1:1 ratio and should not exceed 210 bar.
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
PP ✱ C
B – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C
D 1240 GPM*
L/min. $ 31.90 L
L Standard Screw +$ 0.00
Standard Screw A
A 100 - 3000
7 - 210 bar psi +$ 0.00 N
N Buna-N +$ 0.00
Buna-N
E
F 25 L/min. $ 36.20
80 GPM C
C Tamper Resistant +$ 4.10
Tamper Resistant B
B 50
3,5--1500 psi
105 bar +$ 0.00 V
V Viton
Viton +$ 2.00
G
H 160 L/min. $ 51.80
50 GPM K
K Handknob
Handknob +$ 5.00 C
N 150 - 6000
4 - 55 bar psi +$ 2.00
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
J 320 L/min. Q 4 - 25 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 10 - 315 bar
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
PR ✱ C
B – ✱ ✱✱
Nominal
Capacity Control** Adjustment Range Seal
C
D 1240 GPM*
L/min. $ 31.90 L Standard Screw +$ 0.00
A 100
35 - -210 barpsi +$ 0.00 N Buna-N +$ 0.00
3000
F 80 L/min.
E 25 GPM $ 36.20 C
C B
Tamper Resistant
Tamper Resistant +$ 4.10
B 50 - 1500bar
3,5 - 105 psi +$ 0.00 V V Viton
Viton +$ 2.00
H 160 L/min. K D 1,5 - 55 bar
Handknob
G
J 50320GPM
L/min. $ 51.80 K C
Handknob
E 150
1,5 --25 +$ 5.00
barpsi +$ 2.00
6000
I 100 GPM $ 97.30 S 60
N 1,5--800
14 bar
psi +$ 1.00
W*50 - 315 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Available for PRFB and PRHB
W
A 150 bar psi +$ 0.00
- 4500
50-210
B 20-105 bar Adjustment Range Options:
D 14-55 bar
Adjustment Range Options: PRDB Only:
E B,
A, C, and
7-25 bar W are standard set at 1000 psi.
A is standard set at 70 bar.
N
S Option
3,5-14isbar
standard set at 400 psi.B, D, E, S are standard set at 14 bar.
Q Option is standard set at 200 psi.PRFB, PRHB:
** See page 162 for information * Minimum setting 75 psi on all ranges.
A, W are standard set at 70 bar.
on Control Options Customer may specify pressure setting. +$ 1.10
D is standard set at 25 bar.
E is standard set at 14 bar.
S is standard set at 7 bar.
** See page 162 for information * Not available for PRFB, PRHB
Visit www.sunhydraulics.com for detailed and complete technical
on Control Options Customerinformation
may specifyon our fullsetting.
pressure line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
3
2
2 11
b
cc
b
4
Drain Locating Cartridge Dimensions
3 Shoulder
Cartridge Dimensions
Tank Locating Typical c Installation
Shoulder Capacity Cartridge
Typical Cavity a b c Torque
Installation
Capacity Cartridge
Model Code Cavity a b L C K Torque
(Nm)
Model Code L C K (lb. ft.)
40 L/min. PVDA – LAN T - 21A 34,9 22,2 79 81 85 40/50
aa 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 80 L/min. PVFA – LAN T - 22A 34,9 28,6 88 90 94 60/70
2Inlet 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 160 L/min. PVHA – LAN T - T - 23A 46 31,8 100 102 107 200/215
50 GPM RPGC – LAN 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
1 320 L/min. PVJA – LAN -
Reduced Pressure 100 GPM RPIC – LAN T - 16A 24A
T 63,5
2.44 141,3
1/4” 122
2.44 1262.47 129 2.69 465/500
150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance
Performance Curves
Curves
RPCC PVDA RPEC PVFA RPGC PVHA RPIC PVJA RPKC
Regulated
Typical Pressure
Pressure Rise
Relieving Reducing Relieving Reducing Relieving Reducing
5000 Relieving Reducing
5000
5000 140 5000 140 5000 140 140
120 4000 120 4000 120 4000 120 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
P = bar
100 3000
100 3000
100 3000 100 3000
3000
80 80 80 80
2000 2000 2000 2000 2000
60 60 60 60
1000 40 1000 40 1000 40 1000 40 1000
20 20 20 20
0 5 10 15
0 20 25 0 10 20 30
0 40 50 0 20 40 600 80 100 0 40 80 1200 160 200 0 80 160 240 320 400
Flow = GPM-40 -20 0 20 40 60Flow = GPM-80 -40 0 40 80 Flow
120 = GPM -160 -80 0 80 Flow
160 240 = GPM
-320 -160 0 160 Flow
320 480 = GPM
Q = L/min. Q = L/min. Q = L/min. Q = L/min.
■ Maximum operating pressure = 5000 psi
■
■ Maximum
Will acceptoperating
maximumpressure
pressure= at
350 bar2.
Port
■
■ Factory pressure
Back pressure onsetting established
the tank port (port at
2)blocked control
is directly portat(deadhead)
additive a 1:1 ratio to the valve setting.
■
■ Control
Factory pilot flowsettings
pressure = PVDA: 0,11 to 0,16
established at 4 L/min.,
GPM PVFA: 0,16 to 0,25 L/min., PVHA, PVJA:
■ 0,25 to 0,33
Typical L/min.
response time 10 ms.
■
■ Maximum
Maximum pressure
leakage =atRPCC,
port 3 should
RPEC: be limited
2 in to 210psi,
3/min./1000 bar.RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Pressure on the drain (port 4) is directly additive to the valve setting at a 1:1 ratio and should not
■ exceed 350 bar. setting for all spring ranges is 75 psi
RPCC minimum
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP C – ✱ ✱ ✱
PV ✱ A
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control** Adjustment Range Seal
C 40
D 12 L/min.
GPM* $ 31.90 L Standard
L Standard Screw
Screw +$ 0.00 A 7
A 100 - 3000
- 210 bar psi +$ 0.00 N Buna-N
N Buna-N +$ 0.00
E
F 25 L/min.
80 GPM $ 36.20 C Tamper
C Resistant +$ 4.10
Tamper Resistant B 3,5
B 50 --1500 psi
105 bar +$ 0.00 V Viton
V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
H 160 L/min. K Handknob D 2 - 55 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
J 320 L/min. E 2 - 25 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 10 - 315 bar
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
P = bar
100 3000
100 3000
100 3000 100 3000
3000
80 80 80 80
2000 2000 2000 2000 2000
60 60 60 60
1000 40 1000 40 1000 40 1000 40 1000
20 20 20 20
0 5 10 15
0 20 25 0 10 20 30
0 40 50 0 20 40 60
0 80 100 0 40 80 1200 160 200 0 80 160 240 320 400
Flow = GPM-40 -20 0 20 40 60Flow = GPM-80 -40 0 40 80 Flow
120 = GPM-160 -80 0 80 Flow
160 240 = GPM
-320 -160 0 160 Flow
320 480 = GPM
Q = L/min. Q = L/min. Q = L/min. Q = L/min.
■ Maximum operating pressure = 5000 psi
■
■ Maximum
Will acceptoperating
maximum pressure
pressure= at350 bar2.
Port
■
■ Factory pressure
Back pressure onsetting established
the tank port (port at
2)blocked control
is directly portat(deadhead)
additive a 1:1 ratio to the valve setting.
■
■ Control
Factory pilot flowsettings
pressure = PVDB: 0,11 to 0,16
established at 4 L/min.,
GPM PVFB: 0,16 to 0,25 L/min., PVHB, PVJB: 0,25 to
■ 0,33 L/min.
Typical response time 10 ms.
■
■ Pressure
Maximum at leakage
port 3 is=directly
RPCC, additive
RPEC: 2tointhe valve setting
3/min./1000 psi, at a 1:1 ratio
RPGC: and should psi,
3 in3/min./1000 not exceed
RPIC: 4210 bar.
■ in3/min./1000
By controlling psi,
the RPKC: 3/min./1000 psi.
pressure5atinthe vent (port 4), the effective setting of the valve can be controlled below
■ the
RPCCnominal
minimum valvesetting
setting.for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ B
PV C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control** Adjustment Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 40 L/min. L Standard Screw A 7 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 80 L/min. C Tamper Resistant B 3,5 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
H 160 L/min. K Handknob D 2 - 55 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
J 320 L/min. E 2 - 25 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 10 - 315 bar
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Performance Curves
RPCC RPEC
PBFC RPGC
PBHC RPIC
PBJC RPKC
Typical Pressure
Regulated Rise
Pressure
5000 5000 5000 5000 5000
Relieving Reducing Relieving Reducing Relieving Reducing
140
4000 140
4000 140
4000 4000
P = psi
4000
= psi
P = psi
= psi
= psi
P = Pbar
bar
80 80 80
1000 60
1000 60
1000 60
1000 1000
40 40 40
0 5 10 15 20 25 20 0 10 20 30 40 50 20 0 20 40 60 80 100 200 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
0 30 60 90 120 0 60 120 180 240 0 120 240 360 480
■ MaximumQoperating
= L/min. pressure = 5000Qpsi = L/min. Q = L/min.
■
■ Pilot ratio, air to hydraulic 1:20
Will accept maximum pressure at Port 2.
■
■ Maximum
Back operating
pressure on the pressure
tank port=(port
140 bar
2) is directly additive at a 1:1 ratio to the valve setting.
■ Maximum
Factory air pressure
pressure should
settings not exceed
established 10 bar.
at 4 GPM
■ Typical
Control response
pilot flowtime 10 ms.0,16 to 0,25 L/min., PBHC, PBJC: 0,25 to 0,33 L/min.
= PBFC:
Maximum leakage 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
pressure=differential,
RPCC, RPEC: inlet2toinoutlet = 210 bar.
in 3 /min./1000 psi, RPKC: 5 in 3/min./1000 psi.
■ The pressure at port 3 determines the minimum valve setting and should not exceed 70 bar.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
PB ✱ C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
F
E 80 GPM
25 L/min. $ 36.20 Available
C Tamper in PBFC+$
Resistant only4.10 B 50
B 3,5--1500
105 bar
psi +$ 0.00 N Viton
V Buna-N +$ 2.00
G
H 50 L/min. $ 51.80
160GPM K
A Handknob
1/4" NPTF +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 Pilot Port at N 60 - 800 psi +$ 1.00
J 320 L/min. end of Cartridge
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
B SAE-4
Adjustment Range Options:
Pilot Port at A, B, C, and W are standard set at 1000 psi.
end of Cartridge N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
3
2 1
b c
c 2 1
b
Locating
3 Shoulder
Locating Cartridge Dimensions
Tank
Shoulder Typical Cartridge Dimensions c Installation
Capacity Cartridge Cavity a b Torque
ModelTypical
Code L c C K
Installation (lb. ft.)
a Capacity Cartridge Cavity a b Torque
12 GPM RPCC – LAN
Model Code T - 162A 1.22 3/4” A
2.11 B
2.17 2.31
(Nm) 25/30
a
22 80GPM
25 L/min. PPFC
RPEC – ABN T - T10A
– LAN - 2A 1.5634,9 28,6
7/8” 51
2.00 -
2.06 60/70
2.25 30/35
Outlet
Inlet 160GPM
50 L/min. RPGC – LAN
PPHC – BBN T - T3A
- 17A 1.8846 31,8
1 1/8” -
2.12 63
2.18 200/215
2.38 45/50
100
320GPM
L/min. RPIC – LAN
PPJC – BBN T - T16A
- 19A 2.4463,5 1 1/4”
41,3 2.44
- 2.47
80 2.69
465/500 150/160
Inlet 1 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Reduced Pressure
Performance Curves
RPCC
Performance Curves RPEC RPGC RPIC RPKC
PPFC PPHC
Typical Pressure Rise PPJC
5000 5000 5000 5000 5000
4000 Regulated Pressure
4000 4000 4000
P = psi
4000
P = bar P = psi
P = psi
P = psi
P = bar P = psi
3000 3000 Relieving Reducing 3000 Relieving Reducing 3000 Relieving Reducing 3000
140 140 140
2000 2000 2000 2000 2000
120 120 120
1000
P = bar
1000 100
1000 100
1000 100 1000
80 80 80
20 0 40 80 120 160 200 0 80 160 240 320 400
0 5 10 15 25 60 0 10 20 30 40 50 60 0 20 40 60 80 100 60
Flow = GPM 40 Flow = GPM 40 Flow = GPM 40
Flow = GPM Flow = GPM
20 20 20
■ Maximum operating pressure = 5000 psi
0
-80 -40 0 40 80 120
0
-160 -80 0
160 80 160 240
320 480
0
-320 -160 0
■ Flowmaximum
Will accept = L/min. Flow2.
pressure at Port = L/min. Flow = L/min.
■
■ Backratio,
Pilot pressure onhydraulic
air to the tank port (port 2) is directly
1:20Maximum operatingadditive at a=1:1
pressure 140ratio
bar to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Maximum air pressure should not exceed 10 bar.
■ Typical response time 10 ms.
■ Control pilot flow = PPFC: 0,16 to 0,25 L/min., PPHC, PPJC: 0,25 to 0,33 L/min.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Maximum
3 pressure differential,
3 inlet to
in /min./1000 psi, RPKC: 5 in /min./1000 psi. outlet = 210 bar.
■
■ The
RPCC minimum setting for all spring ranges is 75 psi setting and should not exceed 70 bar.
pressure at port 3 determines the minimum valve
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
PP
RP ✱ C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control**
Control Adjustment Range
Adjustment Range Seal
Seal
Capacity
C
F 12 L/min.
80 GPM* $ 31.90 L Available in PPFC+$
Standard Screw only0.00 A 3,5
B 100--105
3000
barpsi +$ 0.00 N Buna-N
N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
H 160 L/min. A 1/4" NPTF V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
Pilot Port at
JI 320 GPM $ 97.30
100 L/min. end of Cartridge N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Available for PPHC, PPJC only
W 150 - 4500 psi +$ 0.00
B SAE-4
Pilot Port at
end of Cartridge Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
P = bar
5000
P = bar
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ B
PB C – ✱
8 ✱✱
Nominal
Nominal Control Minimum
Capacity Control** AdjustmentControl
Range Seal
Seal
Capacity Pressure
C
D 4012 L/min.
GPM* $ 31.90 8L Standard
T-8A Screw
Cavity in +$ 0.00 A 100 -
D 1,7 bar3000 psi +$ 0.00 N
N Buna-N +$ 0.00
Buna-N
E 25 GPM $ 36.20 C hex body for
Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 80 L/min. pilot operation W 7 bar V Viton
G 50 GPM $ 51.80 K (Pilot
Handknob
valve to +$ 5.00 C 150 - 6000 psi +$ 2.00
H
I 160
100 L/min.
GPM $ 97.30 be ordered N 60 - 800 psi +$ 1.00
separately)
JK GPM $187.00
200 L/min.
320 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
UK Shortcut Catalogue #999-901-244 37
Relief Valves
Reducing and Reducing/Relieving Valves
PILOT OPERATED,
3-WAY, MODULATING BALANCED
ELEMENT WITHPISTON
INTEGRAL PILOT CONTROL CAVITY
Full Adjustment 5 Turns The -8 control option allows a pilot control valve to be incorporated directly
T-8A
3
+ - Cav into the end of the modulating element via the T-8A cavity. These pilot control
cartridges are sold separately and include electro-proportional, solenoid, air
b pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
2 11
c c
3
b
Tank Locating
Shoulder
Locating
Shoulder
Cartridge
Cartridge Dimensions
Dimensions
2 a TypicalTypical c Installation
Installation
Inlet Capacity
Capacity Cartridge
Cartridge Cavity Cavity a a b b c Torque Torque
Model Model
Code Code L C K (Nm) (lb. ft.)
a L/min. RPCC
1240GPM – LAN
PPDB – 8WN T - 162AT - 11A1.22 34,93/4” 2.11
22,2 2.17
30,2 2.31 40/50 25/30
1
2 L/min. RPEC – LAN
Reduced 2580GPM PPFB – 8WN T - 10A T - 2A 1.56 34,97/8” 2.00
28,6 2.06
35,1 2.25 60/70 30/35
Outlet Pressure
50
160 L/min. RPGC
GPM – LAN
PPHB – 8WN T - 3A T - 17A1.88 1 1/8”
46,0 2.12
31,8 2.18
46,0 2.38200/215 45/50
100
320 L/min. RPICPPJB
GPM – LAN
– 8WN T - 16A T - 19A2.44 1 1/4”
63,5 2.44
41,3 2.47
58,7 2.69465/500150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
RPCC PPDB-8 RPEC PPFB-8 RPGC PPHB-8 RPIC PPJB-8 RPKC
Typical
Regulated Pressure Pressure
with RiseStage Installed
T-8A Pilot
Relieving Reducing
5000 Relieving Reducing
5000 Relieving Reducing
5000 Relieving Reducing
5000
5000 344 344 344 344
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
0 5 10 015 20 25 0 10 20 030 40 50 0 20 40 0
60 80 100 0 40 80 0
120 160 200 0 80 160 240 320 400
Flow = GPM
-57 -40 -20 0 20 40 57
Flow = GPM -114 -80 -40 0 40 80 114Flow = GPM
-228 -160 -80 0 80 Flow
160 228 = GPM
-456 -320 -160 0 160 320 456
Flow = GPM
Q = L/min. Q = L/min. Q = L/min. Q = L/min.
■ Maximum operating pressure = 5000 psi
■ .Maximum operating pressure = 350 bar
■ Will accept maximum pressure at Port 2.
■ Control pilot flow = PPDB-8: 0,11 to 0,16 L/min., PPFB-8: 0,16 to 0,25 L/min., PPHB-8, PPJB-8: 0,25
■ Back
to 0,33pressure
L/min. on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
Pressurepressure
Factory at port 3settings established at the
4 GPM
■
■ is directly additive to valve setting at a 1:1 ratio and should not exceed 210 bar.
■
■ Typical response time 10 ms.
Maximum inlet pressure is determined by the bias spring. The D spring is limited to140 bar maximum
■ Maximum leakage
differential pressure=and
RPCC,
the WRPEC: in 3limited
spring2 is /min./1000
to 350psi,bar
RPGC: 3 in3/min./1000
maximum psi, RPIC: 4
inlet pressure.
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ With the -8 control option, the main stage valve should first be installed to the correct torque value. The
■ RPCCpilot
T-8A minimum
controlsetting for all spring
valve should then beranges is 75
installed psithe main stage valve to its required torque value.
into
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ B
PP C – ✱
8 ✱✱
Nominal
Nominal Control MinimumControl
Capacity Control** Adjustment Range Seal
Seal
Capacity Pressure
C
D 4012 L/min.
GPM* $ 31.90 8L T-8A
Standard Screw
Cavity in +$ 0.00 A 1,7
D - 3000 psi +$ 0.00
100bar N
N Buna-N +$ 0.00
Buna-N
E 25 GPM $ 36.20 C hex bodyResistant
Tamper for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 80 L/min. pilot operation W 7 bar V Viton
G 50 GPM $ 51.80 K (Pilot
Handknob
valve to +$ 5.00 C 150 - 6000 psi +$ 2.00
H
I 160 L/min.
100 GPM $ 97.30 be ordered N 60 - 800 psi +$ 1.00
separately)
JK GPM $187.00
200 L/min.
320 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com
Visit www.sunhydraulics.com for
for detailed
detailedand
and complete
complete technical
technical information
information on
onour
our full
full line
line of
of products.
products.
6 US Shortcut Catalogue #999-901-243
pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
P = bar
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
0 0 0 3000 0
3000 -57 -40 -20 0 300020 40 57 -114 -80 -40 0 300040 80 114 -228 -160 -80 0 80 160 228 -456 -320 -160 0 3000
160 320 456
2000 Q = L/min.
2000 Q = L/min.
2000 Q = L/min.
2000 Q = L/min.
2000
1000 1000 1000 1000 1000
0 5 10 15 20
■
25 Maximum
0 10 operating
20 30 pressure
40 50 = 350
0 bar40 60 80 100
20 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Control pilot flow = PVDA-8: 0,11 to 0,16 L/min., PVFA-8: 0,16 to 0,25 L/min., PVHA-8, PVJA-8:
■ Maximum
0,25 to 0,33operating
L/min. pressure = 5000 psi
■
■ Will accept maximum
Maximum pressure at port pressure at Port
3 should be 2.
limited to 210 bar.
■
■ Back pressure on the tank port
Pressure on the drain (port 4) is directly(port 2) isadditive
directlytoadditive
the valve at setting
a 1:1 ratio
at ato theratio
1:1 valve
andsetting.
should not exceed
■ Factory
350 bar. pressure settings established at 4 GPM
■
■ Typical response
Maximum time 10isms.
inlet pressure determined by the bias spring. The D spring is limited to 140 bar maximum
■ differential
Maximum leakagepressure=and RPCC,the W spring2 is
RPEC: in 3limited to 350
/min./1000 psi,bar maximum
RPGC: 3 in3/min./1000
inlet pressure.
psi, RPIC: 4
■ in3/min./1000
With psi, RPKC:
the -8 control option, the
3/min./1000 psi.
5 inmain stage valve should first be installed to the correct torque value.
■ RPCC
The minimum
T-8A setting
pilot control for should
valve all springthen ranges is 75 psi
be installed into the main stage valve to its required torque value.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱A
PV ✱ C –
– ✱ ✱✱
8 ✱ ✱
Nominal
Nominal
Capacity Control**
Control Adjustment Range
Minimum Control Seal
Seal
Capacity Pressure
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 40 L/min. 8 T-8A Cavity in D 1,7 bar N Buna-N
E 25 GPM $ 36.20 C hex
Tamper
bodyResistant
for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F
G 80
50 L/min.
GPM $ 51.80 K Handknob
pilot operation +$ 5.00 W
C 7 bar- 6000 psi
150 +$ 2.00 V Viton
(Pilot valve to
I
H GPM $ 97.30
100 L/min.
160 be ordered N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 separately) Q 60 - 400 psi +$ 1.00
J 320 L/min.
W 150 - 4500 psi +$ 0.00
Performance Curves
RPCC
Performance Curves RPEC RPGC RPIC RPKC
TypicalPRDL
Pressure Rise
5000 5000
Regulated Pressure Command 4000
vs.
5000 5000 5000
4000 4000 4000
P = psi
4000
Secondary Pressure
P = psi
P = psi
P = psi
P = psi
20,0
0 5 10 15 20 25 0 10 20 30 40 50 0 20 4010,0 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow
10,0 = GPM Flow 5,0
= GPM Flow = GPM Flow = GPM
■ Maximum operating
0
-26,5
pressure
0
= 26,5
5000 psi 0 20 40 60 80 100
■ Will accept maximum Q = L/min.
pressure at Port 2. Command (%)
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Maximum operating
Factory pressure pressure
settings = 350 bar
established at 4 GPM
■
■ Maximum valve leakage
Typical response time 10 =ms.328 cc/min. at deadhead
■
■ Pressure
Maximum at leakage
port 3 is=directly
RPCC, additive
RPEC: 2tointhe valve setting
3/min./1000 psi, at a 1:1 ratio
RPGC: and should psi,
3 in3/min./1000 not exceed
RPIC: 4210 bar.
■ in3/min./1000
For psi, RPKC: 5an
optimum performance, in3amplifier
/min./1000
withpsi.current sensing and adjustable dither should be used.
■ Dither
RPCC should
minimum be adjustable
setting for between
all spring100 - 250isHz.
ranges 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP D
PR ✱LC – M
✱ D
✱N✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Operating Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
L 20 L/min. M Manual Override D 3,5 - 35 bar N Buna-N
E 25 GPM $ 36.20 C (Standard)
Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 E
C 1,7
150--18 bar psi
6000 +$ 2.00 V Viton
NOTE: Coil must be
I 100 GPM $ 97.30 ordered separately. Use N 0,7
S 60 -- 800
7 barpsi +$ 1.00
K 200 GPM $187.00 12V DC or 24V DC Q 60 - 400 psi +$ 1.00
(Series 770-***) coils
only. See page 167. W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
1
2 1
e
c
b
d
Locating
Shoulder 2 3
Cartridge Dimensions
Typical c Installation
Capacity Cartridge Cavity a b Torque
b Model Code L C K (lb. ft.)
Cartridge Dimensions
c a 12 GPM RPCC – LAN
Typical T - 162A 1.22 3/4” 2.11 2.17 2.31 Installation
25/30
3 Locating e
2
Drain
Capacity
25 GPM
Cartridge
RPEC –Model
LAN CodeT - 10A
Cavity
1.56
a
7/8”
b c
2.00
d
2.06 (dia.) 2.25
Torque
30/35
Shoulder (Nm)
Outlet
2 a 5020 L/min. RPGCPRDP
GPM – LAN- MDNT - 3A T-11A 1.88 35,11 1/8”22,2 2.12
38,1 70,12.18 37,3 2.38 45/5045/50
Intlet 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
Reduced 1 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Pressure
Performance Curves
RPCC RPEC RPGC RPIC RPKC
Performance Curves Typical Pressure Rise
5000 5000 5000 PRDP 5000 5000
4000 4000 4000 4000
Regulated Pressure Command3000
vs.
P = psi
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP DC
PR ✱ P – M D✱
✱ ✱ N
Nominal
Capacity Control** Adjustment Range
Operating Range Seal
C
P 1220 GPM*
L/min. $ 31.90 L
M Standard Screw +$ 0.00
Manual Override A
D 100
3,5 -- 35
3000
barpsi +$ 0.00 N Buna-N +$ 0.00
(Standard)
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 1,7 - 18 bar V Viton
G 50 GPM $ 51.80 K
NOTE: Coil must be +$ 5.00
Handknob C 150 - 6000 psi +$ 2.00
ordered separately. Use
I 100 GPM $ 97.30 12V DC or 24V DC N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 (Series 770-***) coils Q 60 - 400 psi +$ 1.00
only. See page 167.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
3 2 3
Pilot Operated 44
1 1
3
Atmospherically Referenced,
3 Port Cavity 45
1
3
Vented, 4 Port Cavity 46
4
4000
psi
psi
psi
psi
PP==bar
PP==bar
PP= =bar
P =P bar
PP= =bar
20
3000 20
3000 20
3000 20
3000 20
3000
2000 2000 2000 2000 T 2000
10 T 10 T 10 ILO 10 ILO
T
XEN T 10 XEN
PIL
O XEN ILO XEN LL
P XEN
1000 PIL
O
1000 1000 LP 1000 FU 1000 L LP
LL FU
L
FU
LL FU XCN XCN
XCN FU XCN XCN
0 40 80 120 160 200
0
0
5
15
10
23
15 20
32
25
40
0
0
10
20
20
40
30 40
60
50
80 00 2030 40 60 60 9080 100
120 0 80 160 240 320 00 80
160 160320 240 480
320 640
400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
Q = L/min. Q = L/min. Q = L/min. Q = L/min. Q = L/min.
■ Maximum operating pressure = 5000 psi
■ Maximum operating pressure = 350 bar
■ Will accept maximum pressure at Port 2.
■ Maximum valve leakage = 0,07 cc/min.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ CKBB, CKBD available only with 2 bar or 5 bar check valve cracking pressures.
■ Factory pressure settings established at 4 GPM
■ CK*D has sealed pilot for use in circuits where cross port leakage is undesirable.
■ Typical response time 10 ms.
■ CK*B has unsealed pilot to allow air trapped in the pilot line to be purged from the circuit.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CK ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Capacity Version Control** Adjustment Range Cracking Pressure
Control** Seal Seal
Capacity
B* 30 L/min. C 12 GPM* $ 31.90
B Bleed L Standard Screw X
through Pilot +$ 0.00PilotA 100 - 3000 psi
Standard +$ 0.00
A 0,3 bar N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 60 L/min. D Sealed Pilot Piston L Manual Load B 1,0 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi
Release +$ 2.00
E 120 L/min. C 2,0 bar
I 100 GPM $ 97.30 N 60 - 800 psi
B 1/4" BSPP External +$ 1.00
G 240 L/min. Pilot Port 3 blocked D 3,5 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 480 L/min. E SAE-4 External E 5,0 bar
W 150 - 4500 psi
Pilot Port 3 blocked +$ 0.00
F 7,0 bar
P 1/4" NPTF External
Adjustment Range Options:
Pilot Port 3 blocked
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
* CKBB, CKBD available
on Control Options** See page 162Customer may specifywith
for information pressure E Cracking +$ 1.10
C andsetting.
on Control Options Pressures Only.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
0 5 10 2015 20 25 0 10 20 20
30 40 50 0 20 40 20
60 80 100 0 40 80 20
120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
10 10 10 OT 10 OT
XEN OT XEN OT XEN PIL XEN PIL
PIL PIL LL
XCN
■ Maximum operating pressure = 5000 psi
FU
LL
XCN FU
LL XCN FU
LL
XCN
FU
0 ■
20 Will
40 accept
60 80 maximum
0 30pressure
60 at Port
90 120 2. 0 80 160 240 320 0 160 320 480 640
Q = L/min. Q = L/min. Q = L/min. Q = L/min.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Maximum
Factory operating
pressure pressure
settings = 350 bar
established at 4 GPM
■
■ Maximum
Typical valve leakage
response time 10 =ms.0,07 cc/min.
■
■ Approximately
Maximum 0,07= cc
leakage of fluid
RPCC, will pass
RPEC: 2 in 3from the pilot
/min./1000 psi,area
RPGC: to the3 vented spring chamber
in3/min./1000 every
psi, RPIC: 4
3/min./1000
4000
in cycles. psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ C
CK V – ✱ ✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Cracking Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Standard Pilot A 0,3 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 120GPM
50 L/min. $ 51.80 S Handknob
K External SAE-4 +$ 5.00 B 150
C 1,0 bar
- 6000 psi +$ 2.00 V Viton
Vent Port
IG 100 L/min. $ 97.30
240 GPM N
C 60
2,0-bar
800 psi +$ 1.00
K 200 GPM $187.00 L Manual Load Q 60 - 400 psi +$ 1.00
I 480 L/min. Release External D 3,5 bar
Vent W 150 - 4500 psi +$ 0.00
E 5,0 bar
Adjustment Range Options:
F B,
A, 7,0
C,bar
and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
** See page 162 for information 6 US Shortcut Catalogue #999-901-243
on Control Options
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
20 20 20 20
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow =10GPM Flow =10
GPM Flow = GPM Flow = GPM Flow = GPM
T 10 T 10 OT
XEN ILO XEN T XEN ILO XEN PIL
P ILO LL
P LL
LL L LP FU FU
FU
XCN ■ Maximum operating pressure = 5000 psi XCN FU XCN XCN
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
CV ✱VC –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Adjustment Range Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Standard Pilot A 0,3 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. L Manual Load B 1,0 bar V Viton
G 50 GPM $ 51.80 K Handknob
Release +$ 5.00 C 150 - 6000 psi +$ 2.00
G
I 240 GPM $ 97.30
100 L/min. C
N 2,0
60 -bar
800 psi +$ 1.00
IK GPM $187.00
200 L/min.
480 Q 3,5
D 60 -bar
400 psi +$ 1.00
W 5,0
E 150bar
- 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
Standard, 280 Bar Maximum Setting 48
3
2 1
Standard, 350 Bar Maximum Setting 49
3
2 1
Semi-Restrictive, 280 Bar Maximum Setting 50
3
2 1
Semi-Restrictive, 350 Bar Maximum Setting 51
3
2 1
Restrictive, 280 Bar Maximum Setting 52
3
2 1
Restrictive, 350 Bar Maximum Setting 53
3
2 1
Without Pilot Assist, 3 Port Cavity 54
3
2 1
Atmospherically Referenced, 3 Port Cavity 55
3
4
1
2 Vented, 280 Bar Maximum Setting 56
3
4
1
2 Vented, 420 Bar Maximum Setting 57
3
2 1
c
3
b c
b
Locating
Shoulder Cartridge Dimensions
3 Cartridge Dimensionsc
Pilot Locating Typical Installation
Capacity TypicalCartridge Cavity a b c Installation
Torque
Shoulder
Capacity Cartridge
Model Code Cavity a b L C Torque
(Nm)
Model Code L C K (lb. ft.)
a 60 L/min. CBCA – LHN T - 11A 34,9 22,2 50 56 40/50
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 120 L/min. CBEA – LHN T - 2A 34,9 28,6 61 64 60/70
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Valve
Outlet 240 L/min. CBGA – LHN T - 17A 46 31,8 70 84 200/215
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
480 L/min. CBIA – LHN T - 19A 63,5 41,3 90 104 465/500
Load 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
CBC* CBE* CBG* CBI*
RPCC RPEC RPGC RPIC RPKC
Free Flow and Pilot Open Pressure Drop
Typical Pressure Rise
30 30 30 30
25 5000 25 5000 25 5000 25 5000
5000
P = bar
P = bar
P = bar
P = bar
20 20 20 4000 20
4000 4000 Piloted 4000
P = psi
P = psi
P = psi
P = psi
15 15 15 15
3000 Piloted Ope
Open
3000 3000 Piloted 3000
ed Open 3000
10 10 10 10
Free Flow 2000 Free Flow
2000 2000 5 2000 5 2000
0 Free Flow 0 0 Free Flow 0
1000 1000 1000 1000 1000
0 15 30 45 60 0 30 60 90 120 0 60 120 180 240 0 120 240 360 480
0 5 10 15 20 Q
25 = L/min. 0 10 20 30 40 Q
50 = L/min.0 20 40 60 80 100Q = L/min.0 40 80 120 160 200 Q = L/min.
0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Load holding to 215 bar with 280 bar valve setting
■ Maximum operating pressure = 5000 psi
■ Maximum valve leakage at reseat = 0,4 cc/min.
■ Will accept maximum pressure at Port 2.
■ Reseat exceeds 85% of set pressure
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure setting established at 32,8 cc/min.
■ Factory pressure settings established at 4 GPM
■
■
Counterbalance
Typical responsevalves
time 10should
ms. be set at least 1.3 times the maximum load induced pressure.
■ Back pressure at port 2 adds to the effective relief setting at a ratio of 1 plus the pilot ratio times the
■ Maximum
back leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
pressure.
3 3
in /min./1000 psi, RPKC: 5 in /min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CB ✱RP C –✱✱✱ ✱ ✱
✱✱–
Nominal Nominal
Capacity Version Control** Adjustment Range Cracking Pressure
Control** Seal Seal
Capacity
C 60 L/min. C $ Pilot
A 3:1
12 GPM* 31.90Ratio L Standard Screw L +$ 0.00Screw
Standard A 100 - 3000 psi +$ 1,7
0.00 N Buna-N
Bar Check Spring +$ 0.00
N Buna-N
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
48 UK Shortcut Catalogue #999-901-244
Counterbalance Valves
Relief Valves
STANDARD, 350 BAR MAXIMUM SETTING
PILOT OPERATED, BALANCED PISTON
Turn screw
Full clockwise5 to
Adjustment reduce
Turns
setting and release load.
+
Complete Adjustment - 3 3/4 Turns
- + 2 1
2 1
c
3
b c
b
Locating
Shoulder Cartridge Dimensions
3 Cartridge Dimensionsc
Pilot Locating Typical Installation
Capacity Cartridge
Typical Cavity a b c Torque
Installation
Shoulder
Capacity Cartridge Code Cavity
Model a b L C (Nm)
Torque
Model Code L C K (lb. ft.)
a 60 L/min. CBCG – LJN T - 11A 34,9 22,2 50 56 40/50
2 a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
120 L/min. CBEG – LJN T - 2A 34,9 28,6 61 64 60/70
2
Valve 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 240 L/min. CBGG – LJN T - 17A 46 31,8 70 84 200/215
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
480 L/min. CBIG – LJN T - 19A 63,5 41,3 90 104 465/500
Load 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
CBC* CBE* CBG* CBI*
RPCC RPEC RPGC RPIC RPKC
Free Flow and Pilot Open Pressure Drop
30 30
Typical Pressure
30
Rise 30
25 25 25 5000 25
5000 5000 5000 5000
P = bar
P = bar
P = bar
P = bar
20 20 20 20
4000 4000 4000 4000
Piloted Open
p
P = psi
P = psi
P = psi
P = psi
15 15 15 15
Piloted Ope
Open Piloted
ed Open
3000 3000
3000 10 3000 10 3000 10 10
Free Flow Free Flow
2000 2000 5 2000 5 2000 2000
0 Free Flow 0 0 Free Flow 0
1000 1000 1000 1000 1000
0 15 30 45 60 0 30 60 90 120 0 60 120 180 240 0 120 240 360 480
0 5 10 15 20 Q25= L/min. 0 10 20 30 40 Q
50 = L/min. 0 20 40 60 Q
80 100 = L/min.0 40 80 120 160 200Q = L/min.0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Load holding to 270 bar with 350 bar valve setting
■ Maximum operating pressure = 5000 psi
■ Maximum valve leakage at reseat = 0,4 cc/min.
■ Will accept maximum pressure at Port 2.
■ Reseat exceeds 85% of set pressure
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure setting established at 32,8 cc/min.
■ Factory pressure settings established at 4 GPM
■ Counterbalance valves should be set at least 1.3 times the maximum load induced pressure.
■ Typical response time 10 ms.
■ Back pressure at port 2 adds to the effective relief setting at a ratio of 1 plus the pilot ratio times
■ Maximum
the back leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
pressure.
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CB ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Capacity Version Control** Control**Adjustment RangeCracking Pressure
Seal Seal
Capacity
C 60 L/min. C $ 31.90
G 4.5:1
12 GPM* Pilot RatioL Standard ScrewL Standard
+$ 0.00Screw
A 100 - 3000 psi +$ 1,7
0.00 N Buna-N
Bar Check Spring +$ 0.00
N Buna-N
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
UK Shortcut Catalogue #999-901-244 49
Counterbalance Valves
SEMI-RESTRICTIVE,
Relief Valves 280 BAR MAXIMUM SETTING
PILOT OPERATED,
Turn screw clockwise to reduce
setting and release load.
BALANCED PISTON
Complete Adjustment 3 3/4 Turns
Full Adjustment 5 Turns
-
+
+
- 2 1
2 1
b 3
c c
b
Cartridge Dimensions
3 Locating Typical c Installation
Pilot Shoulder
Locating Capacity Cartridge Cavity a b Torque
Shoulder Model Code Cartridge L
Dimensions C (Nm)
Typical c Installation
Capacity CBBC – LHN CavityT - 11A a
40 L/min. Cartridge 34,9 b 22,2 50 56 40/50
Torque
a L C K
2 80 L/min. ModelCBDC
Code – LHN T - 2A 34,9 28,6 61 64 (lb. ft.)
60/70
Valve a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
160 L/min. CBFC – LHN T - 17A 46 31,8 70 84 200/215
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Load 1 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
CBB* CBD* CBF*
Performance Curves
Free Flow and Pilot Open Pressure Drop
RPCC RPEC
30
RPGC
30
RPIC
30
RPKC
25 25 25
Typical Pressure Rise
P = bar
P = psi P = bar
P = psi P = bar
20 20 20
15 5000 Piloted Open
5000 5000Piloted Open 5000 Piloted Open 5000
10 10 10
4000 4000 4000 4000
P = psi
4000 5
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CB ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Capacity Version Control** Adjustment Range Cracking Pressure
Control** Seal Seal
Capacity
B 40 L/min. C $ 31.90
B 1.5:1
12 GPM* L Standard Screw L
Pilot Ratio +$ 0.00Screw
Standard A 100 - 3000 psi +$ 1,7
0.00 N Buna-N
Bar Check Spring +$ 0.00
N Buna-N
(with sealed pilot)
D 80 L/min. E 25 GPM $ 36.20 C Tamper Resistant
C +$ 4.10
Tamper B 50 - 1500 psi
Resistant +$
H 700.00 V Viton
- 280 bar +$ 2.00
V Viton
G 50 GPMC 3:1 Pilot
$ 51.80 Ratio K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
F 160 L/min. (with sealed pilot) I 25 - 105 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 0,3
1.00
Bar Check Spring
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
50 UK Shortcut Catalogue #999-901-158
6 US Shortcut Catalogue #999-901-243
Counterbalance Valves
SEMI-RESTRICTIVE,
Relief Valves 350 BAR MAXIMUM SETTING
PILOT OPERATED,
Turn screw clockwise to reduce
setting and release load.
BALANCED PISTON
Complete Adjustment 3 3/4 Turns
Full Adjustment 5 Turns
-
+
+
- 2 1
2 1
b 3
c c
b
Cartridge Dimensions
3
Pilot
Locating
Locating Typical c Installation
Shoulder Capacity Cartridge Cavity a b Torque
Shoulder
Model Code Cartridge L
Dimensions C (Nm)
Typical c Installation
40 L/min.
Capacity CBBD – LJN CavityT - 11A a
Cartridge 34,9 b 22,2 50 56 40/50
Torque
2 a ModelCBDD
Code – LJN L C K (lb. ft.)
80 L/min. T - 2A 34,9 28,6 61 64 60/70
Valve a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
160 L/min. CBFD – LJN T - 17A 46 31,8 70 84 200/215
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Load 1 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
CBB* CBD* CBF*
Performance Curves
Free Flow and Pilot Open Pressure Drop
RPCC RPEC
30
RPGC
30
RPIC
30
RPKC
25 25 25
Typical Pressure Rise
P = bar
P = psi P = bar
P = psi P = bar
20 20 20
15 5000 Piloted Open
5000 5000
Piloted Open 5000 Piloted Open 5000
10 10 10
4000 4000 4000 4000
P = psi
4000 5
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CB ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Capacity Version Control** Adjustment RangeCracking Pressure
Control** Seal Seal
Capacity
B 40 L/min. C $ 31.90
D 4.5:1
12 GPM* Pilot RatioL Standard ScrewL +$ 0.00Screw
Standard A 100 - 3000 psi +$ 1,7
0.00 N Buna-N
Bar Check Spring +$ 0.00
N Buna-N
(with sealed pilot)
D 80 L/min. E 25 GPM $ 36.20 C Tamper Resistant
C +$ 4.10
Tamper B 50 - 1500 psi
Resistant +$ 140
J 0.00
- 350 V
bar Viton +$ 2.00
V Viton
G 50 GPML 2.3:1 Pilot
$ 51.80 RatioK Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
F 160 L/min. (with sealed pilot) K 70 - 175 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 0,3
1.00
Bar Check Spring
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
UK Shortcut Catalogue #999-901-158 51
6 US Shortcut Catalogue #999-901-243
Counterbalance Valves
RESTRICTIVE, 280 BAR MAXIMUM SETTING
Relief Valves
Turn screw clockwise to reduce
PILOT
setting andOPERATED,
release load.
Complete Adjustment 3 3/4 Turns
BALANCED PISTON
- + 5 Turns
Full Adjustment 2 1
+ -
3
b c 2 1
c
b Cartridge Dimensions
3
Pilot Locating Typical c Installation
Locating Capacity Cartridge Cavity a b Torque
Shoulder
Shoulder Model Code L C (Nm)
Cartridge Dimensions
15 L/min. CBBA – LHN
Typical T - 11A 34,9 22,2 50 c 56 40/50
Installation
a Capacity Cartridge Cavity a b Torque
2 30 L/min. ModelCBDA
Code – LHN T - 2A 34,9 28,6 L 61 C 64 K 60/70
(lb. ft.)
Valve a 12 60
GPML/min. RPCCCBFA
– LAN– LHNT - 162A
T - 17A 1.22 46 3/4” 31,8 2.11 70 2.17 84 2.31 25/30
200/215
2 25 80
GPML/min. RPEC CBHA
– LAN– LHNT - 10AT - 19A 1.56 63,5 7/8” 41,3 2.00 90 2.06 104 2.25 30/35
465/500
Outlet
Load 1
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
CBB* CBD* CBF* CBH*
Performance Curves
Free Flow and Pilot Open Pressure Drop
RPCC RPEC RPGC RPIC RPKC
30 30 30 30
25
Piloted Open
25
Piloted Open Typical Pressure Rise 25
Piloted Open
25
Piloted Open
P = bar
P = bar
P = bar
P = bar
20 20 20 20
5000 15 5000 15 5000 15 5000 15 5000
10 4000 10 4000 10 4000 10 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CB ✱RP
✱ ✱ –C –✱✱✱ ✱
✱✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Cracking Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 15 L/min. A 3:1 Pilot Ratio L Standard Screw 1,7 Bar Check Spring N Buna-N
E 25 GPM $ 36.20
(with C Tamper Resistant +$ 4.10 B 50 - 1500 psi
sealed pilot) +$ 0.00 V Viton +$ 2.00
D 30 L/min. C Tamper Resistant H 70 - 280 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
F 60 L/min. I 100 GPM Available
$ 97.30in CBBY only N 60 - 800 psi I 251.00
+$ - 105 bar
H 80 L/min. K $187.00
Y 2:1
200 GPM Pilot Ratio Q 60 - 400 psi +$ 1.00
(with Bleed through 0,3 Bar Check Spring
Pilot) W 150 - 4500 psi +$ 0.00
A 70 - 280 bar
B 25 - 105 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
Adjustment Range Options:
** See page 162 for information * Minimum setting 75 psiAonand
allHranges.
are standard set at 210 bar.
on Control Options** See page 162Customer may specify pressure
for information standard set+$
setting.
I and B are 1.10
at 70 bar.
on Control Options Customer may specify setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
3
b c 2 1
c
b Cartridge Dimensions
3
Pilot Locating Typical c Installation
Locating Capacity Cartridge Cavity a b Torque
Shoulder
Shoulder Model Code L C (Nm)
Cartridge Dimensions
15 L/min. CBBG – LJN
Typical T - 11A 34,9 22,2 50 c 56 40/50
Installation
a Capacity Cartridge Cavity a b Torque
2 30 L/min. ModelCBDG
Code – LJN T - 2A 34,9 28,6 L 61 C 64 K 60/70
(lb. ft.)
Valve a 12 60
GPML/min. RPCCCBFG
– LAN– LJNT - 162A
T - 17A 1.22 46 3/4” 31,8 2.11 70 2.17 84 2.31 25/30
200/215
2 25 80
GPML/min. RPEC CBHG
– LAN– LJNT - 10AT - 19A 1.56 63,5 7/8” 41,3 2.00 90 2.06 104 2.25 30/35
465/500
Outlet
Load 1
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
CBB* CBD* CBF* CBH*
Performance Curves
Free Flow and Pilot Open Pressure Drop
RPCC RPEC RPGC RPIC RPKC
30 30 30 30
25
Piloted Open
25
Piloted Open Typical Pressure Rise 25
Piloted Open
25
Piloted Open
P = bar
P = bar
P = bar
P = bar
20 20 20 20
5000 15 5000 15 5000 15 5000 15 5000
10 4000 10 4000 10 4000 10 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
5 5
3000 3000
Free Flow 3000
Free Flow 3000 Free Flow 3000 Free Flow
0 0 0 0
2000 0 15 30 2000
45 60 0 30 60 2000 90 120 0 60 2000 180
120 240 0 120 2000
240 360 480
1000 Q = L/min.
1000 Q = L/min.
1000 Q = L/min. 1000
Q = L/min.
1000
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CB ✱RP C –✱✱✱ ✱
✱✱– ✱✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Cracking Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 15 L/min. G 4.5:1 Pilot Ratio L Standard Screw 1,7 Bar Check Spring N Buna-N
E 25 GPM $ 36.20
(with C Tamper Resistant +$ 4.10 B 50 - 1500 psi
sealed pilot) +$ 0.00 V Viton +$ 2.00
D 30 L/min. C Tamper Resistant J 140 - 350 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
F 60 L/min. I 100 GPM $ 97.30 N 60 - 800 psi K 701.00
+$ - 175 bar
D 70 - 175 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
Adjustment Range Options:
** See page 162 for information * Minimum setting 75 psiJon allCranges.
and are standard set at 210 bar.
on Control Options** See page 162Customer may specify pressure
for information K and D setting. +$at 1.10
are standard set 140 bar.
on Control Options Customer may specify setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
2 1
b c
c 3
b
Locating
3 Shoulder Cartridge Dimensions
Locating Cartridge Dimensions
Typical c Installation
Shoulder Capacity Typical
Cartridge Cavity a b c Installation
Torque
Capacity Cartridge
Model Code Cavity a b L C Torque
(Nm)
Model Code L C K (lb. ft.)
RPCCCCCA
– LAN– LANT - 162A
a 60 L/min. T - 11A 34,9 22,2 50 56 40/50
2 a 12 GPM 1.22 3/4” 2.11 2.17 2.31 25/30
2
Valve 25120
GPML/min. RPECCCEA
– LAN– LANT - 10A
T - 2A 1.56 34,9 7/8” 28,6 2.00 61 2.06 73 2.25 60/70
30/35
Outlet
50240
GPML/min. RPGCCCGA
– LAN– LANT - 3AT - 17A 1.88 46 1 1/8” 31,8 2.12 70 2.18 84 2.38 200/215
45/50
100480
GPML/min. RPIC CCIA
– LAN– LANT - 16A
T - 19A 2.44 63,51 1/4” 41,3 2.44 90 2.47 104 2.69 465/500
150/160
Load 1
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
RPCC CCCA RPEC CCEA RPGC CCGA RPIC CCIA RPKC
Typical
Typical Pressure
Relief Rise
Characteristics
5000 350 5000 350 5000 350 5000 350 5000
300 4000 300 4000 300 4000 300 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
3000 200 3000 200 3000 200 3000 200 3000
2000 150 2000 150 2000 150 2000 150 2000
100 100 100 1000 100
1000 1000 1000 1000
50 50
0 0 0 0 40 80 1200 160 200
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 80 160 240 320 400
0 15 30 45 60 0 30 60 90 120 0 60 120 180 240
Flow = GPM Flow = GPM Flow = GPM Flow = GPM0 120 240 360 480
Flow = GPM
Q = L/min. Q = L/min. Q = L/min. Q = L/min.
■ Maximum operating pressure = 5000 psi
■
■ Maximum
Will acceptoperating
maximum pressure
pressure= at
280 bar2.
Port
■
■ Maximum valve
Back pressure onleakage
the tankatport
reseat = 0,4
(port cc/min.
2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Reseat
Factoryexceeds
pressure85% of setestablished
settings pressure at 4 GPM
■
■ Typical response
Factory time 10established
pressure setting ms. at 32,8 cc/min.
3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
■ Counterbalance valves should be set 2atinleast
Maximum leakage = RPCC, RPEC: 1.3 times the maximum load induced pressure.
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Back pressure at port 2 is directly additive to the relief setting of the valve.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CC ✱RP
A ✱ –C –✱✱✱ ✱
✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Cracking Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. A Standard L Standard Screw 1,7 Bar Check Spring N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. C Tamper Resistant H 70 - 280 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 240 L/min. I 100 GPM $ 97.30 N 60 - 800 psi I+$ 251.00
- 105 bar
B 25 - 105 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Adjustment Range Options:
A and H are standard set at 210 bar.
** See page 162 for information I and B are standard set at 70 bar.
on Control Options Customer may specify setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
c
b 2 1
3
c
Atm.
b Reference
Cartridge Dimensions
3 Locating Typical c Installation
Shoulder
Locating
Pilot Capacity Cartridge Cavity a b
Cartridge Dimensions Torque
Shoulder Model Code L C (Nm)
Typical c Installation
Capacity
60 L/min. CACA – LHN CavityT - 11A a
Cartridge 34,9 b 22,2 L 74 C
81 K
Torque
40/50
2 a Model Code (lb. ft.)
RPCCCAEA
– LAN– LHNT - 162A
a 120 L/min.
12 GPM
T - 2A
1.22
34,9
3/4”
28,6
2.11
84
2.17
90
2.31
60/70
25/30
Valve
2 25240
GPML/min. RPECCAGA
– LAN– LHNT - 10A
T - 17A 1.56 46 7/8” 31,8 2.00 96 2.06 101 2.25 200/215
30/35
Outlet
50480
GPML/min. RPGCCAIA
– LAN– LHNT - 3AT - 19A 1.88 63,51 1/8” 41,3 2.12 117 2.18 126 2.38 465/500
45/50
Load 1
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
Performance Curves 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
PerformanceCAC*
Curves CAE* CAG* CAI*
RPCC RPEC RPGC
Free Flow and Pilot Open Pressure RPIC
Drop RPKC
20 20 Typical Pressure
20 Rise 20
16 16 16 16
5000 5000
P = bar
P = bar
5000 5000
P = bar
P = bar
5000
12 12 12 12
4000 4000 4000 4000
P = psi
P = psi
P = psi
P = psi
8 8 8 3000
8
3000 3000 3000 3000
4 4 4 4
2000 2000
Piloted Open 2000
Piloted Open 2000Piloted Open 2000 Piloted Open
0 0 0 0
1000 1000 1000 1000
0 15 30 45 60 0 30 60 1000 90 120 0 60 120 180 240 0 120 240 360 480
0 5 10 15 20 Q25= L/min. 0 10 20 30 40 Q
50 = L/min. 0 20 40 60 80 100Q = L/min.0 40 80 120 160 200 Q = L/min.
0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■
■ Load
Maximumholding to 210 bar
operating with 280
pressure bar psi
= 5000 valve setting for CA*A, CA*K; 320 bar with 420 bar
■ valve settingmaximum
Will accept for CA*G,pressure
CA*L. at Port 2.
■
■ Maximum
Back pressurevalve
onleakage
the tankatport
reseat = 0,4
(port 2) iscc/min.
directly additive at a 1:1 ratio to the valve setting.
■
■ Reseat exceeds 85% of set pressure
Factory pressure settings established at 4 GPM
■
■ Factory pressure setting
Typical response time 10established
ms. at 32,8 cc/min.
■
■ Free
Maximum leakage = RPCC, RPEC: 22,8
flow check cracking pressure = in 3bar
/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Counterbalance valves should be set at least 1.3 times the maximum load induced pressure.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CA ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Capacity Version Control** Adjustment RangeCracking Pressure
Control** Seal Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. A 3:1 Pilot Ratio L Standard Screw A and K Pilot Ratios N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. G 5:1 Pilot Ratio C Tamper Resistant H 70 - 280 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 240 L/min. K 1:1 Pilot Ratio I 25 - 105 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 480 L/min. K L 2:1$187.00
200 GPM Pilot Ratio Q 60 - 400 psi +$ 1.00
G and L Pilot Ratios
W 150 - 4500 psi +$ 700.00
F - 175 bar
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical US Shortcut Catalogue #999-901-243
4000 20 20 20 20
P = psi
P = psi
P = psi
P = psi
■
■
Will
Loadaccept maximum
holding to 210 barpressure
with 280 at Port 2. setting
bar valve
■
■
Back
Maximum valve leakage at reseat = 0,4iscc/min.
pressure on the tank port (port 2) directly additive at a 1:1 ratio to the valve setting.
■
■
Factory pressure settings established
Reseat exceeds 85% of set pressure at 4 GPM
■ Typical response time 10 ms.
■ Factory pressure setting established at 32,8 cc/min.
■
■
Maximum leakage
Free flow check = RPCC,
cracking RPEC:= 22,8
pressure in 3bar
/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Counterbalance valves should be set at least 1.3 times the maximum load induced pressure.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CW ✱RP
✱ ✱ –C –✱✱✱ ✱
✱✱
Nominal Nominal
Capacity Version Control** Adjustment Range Cracking Pressure
Control** Seal Seal
Capacity
C 60 L/min. C 12 GPM* $ Pilot
A 3:1 31.90Ratio L Standard Screw L +$ 0.00Screw
Standard A 100 - 3000 psi +$ 0.00PilotNRatios
Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. K 1:1 Pilot Ratio C Tamper Resistant H 70 - 280 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 240 L/min. I 25 - 105 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 480 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6
Visit www.sunhydraulics.com for detailed and complete technical US Shortcut Catalogue #999-901-243
information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
P = bar
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CW ✱RP C –✱✱✱ ✱ ✱
✱✱–
Nominal Nominal
Capacity Version Control** Adjustment Range Cracking Pressure
Control** Seal Seal
Capacity
C 60 L/min. C $ Pilot
G 5:1
12 GPM* 31.90Ratio L Standard Screw L +$ 0.00Screw
Standard A 100 - 3000 psi +$ 0.00PilotNRatios
Buna-N +$ 0.00
N Buna-N
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
US Shortcut Catalogue #999-901-243
2
3
2 To 1 Free Flow, with Customer Specified
Orifice, Port 3 Blocked, 3 Port Cavity 64
1
4000
P = psi
P = psi
P = psi
P = psi
CXBA 3000
CXDA 3000
CXFA 3000
CXHA
2000
3000
CXJA
3000
2000 2000 2000 2000
1000 1000 Typical
1000 Pressure Drop 1000 1000
P = bar
P = bar
P = bar
P = bar
P = bar
6 XEN
■ Maximum
6 operating pressure6 = 5000 psi
XEN
6
XEN
6
XEN XEN
3 XCN
XAN
■ Will
3 accept maximum pressure
XCN
XAN
3 at Port 2. 3 XCN
XAN
3 XCN
XAN
XCN
XAN
0 10 20 30
■
40 Back0 pressure
20 40 on the
60 tank
80 port0 (port
30 2) 60
is directly
90 120 additive
0 at 80
a 1:1160ratio
240 to320
the valve0 setting.
160 320 480 640
Q = L/min. ■ Q = L/min.settings establishedQat
Factory pressure = L/min.
4 GPM Q = L/min. Q = L/min.
■
■ Typical
Maximum response
operatingtimepressure
10 ms. = 350 bar
■
■ Maximum
Maximum leakage
valve = RPCC,
leakage RPEC:
= 0,07 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
cc/min.
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Will accept 350 bar at ports 1 and 2.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
CX ✱ C
A – ✱ ✱✱
Nominal
Capacity Control** Adjustment Range
Cracking Pressure Seal
C
B 1240 GPM*
L/min. $ 31.90 L
X Standard Screw
Non-adjustable +$ 0.00 A 100 - 3000 psi
0,3 bar +$ 0.00 N Buna-N +$ 0.00
E
D 25
80 GPM
L/min. $ 36.20 C Tamper Resistant +$ 4.10 B 50
1,0-bar
1500 psi +$ 0.00 V Viton +$ 2.00
G
F 50 L/min. $ 51.80
160GPM K Handknob +$ 5.00 C 150 - 6000 psi
2,0 bar +$ 2.00
IH 100 L/min. $ 97.30
320 GPM N
D 60
3,5-bar
800 psi +$ 1.00
K
J 200 L/min. $187.00
640 GPM Q
E 60
5,0-bar
400 psi +$ 1.00
F 150
W 7,0 bar
- 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
** See page 162 for information 6 US Shortcut Catalogue #999-901-243
on Control Options
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
P = bar
12 Flow = GPM 12 Flow = GPM 12 12 12
8 8 8 XEN
XEN ■ Maximum operating pressure8 = 5000 psi
XEN XEN 8 XEN
P
0 10 20 30
■
40
Will0accept
20
maximum
40
XAN
60
pressure0 at Port 2.
80 60 90 120 0 160 240 320 0 160 320 480
XAN XAN
640
Q = L/min.
■ Back pressure on the tank port (port Q2)= L/min.
Q = L/min. is directly additive at aQ1:1 ratio to the valve setting.
= L/min. Q = L/min.
■ Factory pressure settings established at 4 GPM
■ Maximum operating pressure = 350 bar
■ Typical response time 10 ms.
■ Maximum valve leakage = 0,07 cc/min. 3
■ Maximum leakage = RPCC, RPEC: 2 in /min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Will accept 350psi,
in3/min./1000 barRPKC:
at ports5 1inand 2.
3/min./1000 psi.
■
■ CXAD only available with 0,3, 2
RPCC minimum setting for all spring ranges and 5 bar cracking
is 75 psipressures.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
CX ✱DC –– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Cracking Range
Pressure Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A* 30 L/min. X Non-adjustable A 0,3 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 60 L/min. B 1,0 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
E 120 L/min. C 2,0 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
G 240 L/min. D 3,5 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 480 L/min. E 5,0 bar
FW 7,0
150bar
- 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 3 1
b
c
b c
Locating
Shoulder 1
Cartridge Dimensions
Locating Typical c Installation
Shoulder Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4”Cartridge Dimensions
2.11 2.17 2.31 25/30
2 Typical c Installation
a Capacity RPEC – LAN
25 GPM T - 10A
Cartridge 1.56
Cavity 7/8”
a 2.00b 2.06 2.25 30/35
Torque
2
Outlet
Model Code X (Nm)
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Inlet
RPIC –CXCE
LAN – XCN
60 L/min.
100 GPM T - 16A T - 11A
2.44 134,9
1/4” 22,2
2.44 2.47 31 2.69 40/50
150/160
Inlet 1 L/min.RPKC –CXEE
200 120
GPM LAN – XCN
T - 18A T - 2A
3.13 134,9
5/8” 28,6
2.81 2.94 35 3.06 60/70
350/375
240 L/min. CXGE – XCN T - 17A 46 31,8 46 200/215
Performance
Outlet 1 Curves
480 L/min. CXIE – XCN T - 19A 63,5 41,3 59 465/500
RPCC RPEC RPGC RPIC RPKC
Typical Pressure Rise
Performance Curves 5000 5000 5000 5000
5000
CXCE 4000
CXEE 4000
CXGE 4000
CXIE 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
12 12 12 12
8
XEN
■ Maximum operating pressure = 5000 psi 8 8
P
XEN
XEN XEN
4
■ XANWill accept maximum pressure at Port 2. 4 XAN XAN XAN
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
CX ✱ C
E – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control**
Adjustment Range
Cracking Pressure
Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Non-adjustable A 0,3 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. B 1,0 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 240 L/min. C 2,0 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 480 L/min. D 3,5 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
E 5,0 bar
W 150 - 4500 psi +$ 0.00
F 7,0 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
b c
b c
Locating
Shoulder
Locating
Shoulder 1
Cartridge Dimensions
Typical c Installation
Capacity Cartridge Cavity a b Torque
a Model Code CartridgeLDimensions
C K (lb. ft.)
a 12 GPM RPCC – LAN
Typical T - 162A 1.22 3/4” 2.11 2.17 c 2.31 Installation
25/30
2 Capacity Cartridge Cavity a b Torque
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 X 2.25 30/35
Port
Outlet Model Code (Nm)
30 L/min. RPGC –CNBC
50 GPM LAN – XCN
T - 3A 1.88
T - 162A 1 1/8”
31,0 2.12
19,1 2.1820,8 2.38 45/50
35/40
1 Port 100 60
GPML/min. RPIC –CNDC
LAN – XCN
T - 16A 2.44
T - 13A 1 1/4”
35,1 2.44
22,2 2.4719,1 2.69 150/160
45/50
Inlet 1
200120
GPML/min. RPKC – LAN
CNFC – XCN- 18A
T 3.13
T - 5A 1 5/8”
41,4 2.81
28,6 2.9417,5 3.06 350/375
60/70
Performance Curves 240 L/min. CNHC – XCN T - 16A 61,7 31,8 24,6 200/215
RPCC RPEC 480 L/min. CNJC
RPGC– XCN T - 18A RPIC
79,5 41,3 RPKC
30,2 465/500
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
P = bar
P = bar
0 10 20 30
■
40 Will0 accept
20 maximum
40 60 80pressure
0 at Port
30 2.
60 90 120 0 80 160 240 320 0 160 320 480 640
Q = L/min. ■ Back pressure on the tank port (port Q2)= L/min.
Q = L/min. is directly additive at aQ1:1
= L/min. Q = L/min.
ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Maximum operating pressure = 350 bar
■ Typical response time 10 ms.
■ Will accept 350 bar at ports 1 and 2.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Orifice range =psi,
in3/min./1000 CNBC,
RPKC: CNDC: 0,4 - 1,6 mm,
5 in3/min./1000 psi.CNFC: 0,4 - 2,0 mm, CNHC: 0,4 - 2,4 mm,
■
CNJC: 0,4 - 3,2 mm.
RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
CN ✱CC –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Cracking Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 30 L/min. X Non-adjustable A 0,3 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
D
G 60
50 L/min.
GPM $ 51.80 K Handknob +$ 5.00 B
C 1,0
150bar
- 6000 psi +$ 2.00 V Viton
F
I 120
100 L/min.
GPM $ 97.30 C 2,0 bar
N 60 - 800 psi +$ 1.00
H
K 240
200 L/min.
GPM $187.00 D
Q 3,5
60 -bar
400 psi +$ 1.00
J 480 L/min. E 5,0 bar
W 150 - 4500 psi +$ 0.00
F 7,0 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
0 5 10 12
15 20 25 0 10 20 30
12 40 50 0 20 40 1260 80 100 0 40 80 12120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
8 8 8
XEN
P
XEN
XEN XEN
4 ■
XAN Maximum operating pressure = 5000 psi 4 XAN XAN XAN
0 ■
20 Will
40 accept
60 80 maximum0 30pressure
60 at Port
90 120 2. 0 80 160 240 320 0 320 480 640
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ D
CN C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Cracking Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Non-adjustable A 0,3 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E 120 L/min. B 1,0 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 240 L/min. C 2,0 bar
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 480 L/min. D 3,5 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
E 5,0 bar
W 150 - 4500 psi +$ 0.00
F 7,0 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Customer specified orifice setting range:
CNCD: 0.4 - 1,6 mm
CNED: 0,4 - 2,0 mm
Visit www.sunhydraulics.com
** See page 162for
fordetailed and complete CNGD:
information technical information
0,4 - 2,4 mm on our full line of products.
on Control Options 6
CNID: 0,4 - 3,2 mm US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Locating
Shoulder
Cartridge Dimensions
c Typical c Installation
b Capacity Cartridge Cavity a b Torque
1 Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 Locating 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet Shoulder
50 GPM RPGC – LAN T - 3A 1.88 Cartridge2.12
1 1/8” Dimensions
2.18 2.38 45/50
Maximum Typical c Installation
100Nominal
GPM RPIC –Cartridge
LAN T - 16A
Cavity 2.44 a 1 1/4” b 2.44 2.47 2.69 150/160
Torque
Inlet 1 Orifice Model Code L H K (Nm)
a 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
4,0 mm dia. NFBC – LCN T - 162A 31 19,1 41 - 45 35/40
2
Performance Curves
Port 4,8 mm dia. NFCC – LCN T - 13A 34,9 22,2 58 64 64 40/50
RPCC RPEC 6,3 mm dia. RPGC
NFDC – LAN T - 5A RPIC
41,1 28,6 67 72RPKC
73 60/70
4000
P = psi
P = psi
P = psi
P = psi
Performance
3000 Curves 3000 3000 3000 3000
2000
NFBC NFCC NFDC NFEC NFFC
2000 2000 2000 2000
1000 1000 1000 1000 1000
0 5 10 15 20 25 0 10 20 30 Adjustment
40 50 Sensitivity
0 20 40 at 60
7 bar
80 Differential
100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
20 30 75 150 300
17 ■ Maximum operating pressure63
25
= 5000 psi 125 250
Q = L/min.
Q = L/min.
Q = L/min.
Q = L/min.
Q = L/min.
13 20 50 100 200
10 ■ Will
15 accept maximum pressure 38 at Port 2. 75 LAN
150 LEN
LGN
0 1 2 3 4 ■ 5 Factory
0 1pressure
2 3 settings
4 5 established at 4 GPM
0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5
Number of Turns Number of Turns Number of Turns Number of Turns Number of Turns
■ Typical response time 10 ms.
■
■ Maximum operating
Maximum leakage = pressure
RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
=3 350 bar
3
in /min./1000 psi, RPKC: 5 in /min./1000 psi.
■ Maximum valve leakage at shutoff = less than 0,4 cc/min.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ C – ✱ ✱ ✱
NF
Nominal
Maximum
Capacity Control** Adjustment Range Seal
Nominal Control** Orifice Options Seal
C Orifice
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 4,0
E 25 GPMmm dia. $ 36.20 L
C Standard Screw +$ 4.10
Tamper Resistant B 50 - 1500NFBC
psi +$ 0.00 V N Buna-N
Viton +$ 2.00
C 4 mm
G
C mm dia. $ 51.80
50 GPM
4,8 K Calibrated
H Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 Handknob with N 60 - 800NFCC
psi +$ 1.00
D 6,3 mm dia. Detent Lock C 4,8 mm
K 200 GPM $187.00 Q
D 60 -mm
2,5 400 psi +$ 1.00
E 9,6 mm dia. K Handknob
W 150 - 4500 psi +$ 0.00
NFDC
F 14,2 mm dia. A 6,3 mm
B 3,2 mm
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
NFEC
N Option is standard set at 400 psi.
E 9,6 mm
Q Option is standard set at 200 psi.
F 7,1 mm
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
NFFC
G 14,2 mm
H 9,6 mm
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b
Locating
c Shoulder
b Cartridge Dimensions
Typical c Installation
Capacity
1 Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a
Locating 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Shoulder
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet Cartridge Dimensions
50 GPM RPGC Typical
– LAN T - 3A 1.88 1 1/8” 2.12 2.18
c 2.38 45/50
Installation
Nominal
2 a 100Orifice
GPM RPIC Cartridge
– LAN Cavity
T - 16A 2.44a b
1 1/4” 2.44
L 2.47
H K2.69
Torque
150/160
Inlet 1 Model Code (Nm)
Port 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
8,4 mm dia. NFCD – LFN T - 13A 34,9 22,2 58 64 64 40/50
Performance Curves 12,7 mm dia. NFDD – LGN T - 5A 41,1 28,6 67 72 73 60/70
RPCC RPEC17,5 mm dia. NFED RPGC
– LHN T - 16A RPIC 31,8
61,9 73 79RPKC79 200/215
1
Port
21,6 mm dia. NFFD –Typical
LIN T - 18ARise
Pressure 79,4 41,3 84 90 90 465/500
5000 5000 5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
Performance
3000 Curves 3000 3000 3000 3000
2000 2000 2000 2000 2000
1000 NFCD 1000 NFDD 1000 NFED 1000 NFFD 1000
Q = L/min.
Q = L/min.
300 600
120 120
■
80 Will accept maximum 80 pressure at Port 2.200 380
95 200
■ 40 Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
40
0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5
■ Factory pressure
Number of Turns
settings established
Number of Turns
at 4 GPM Number of Turns Number of Turns
■ Typical response time 10 ms.
■
■ Maximum
Maximum operating
leakage = pressure = 350 bar
RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Maximum valve leakage at shutoff = less than 0,4 cc/min.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱D
NF ✱ C –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Orifice Options Seal
Orifice
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 8,4 mm dia. L Standard Screw NFCD N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 8,4
F 50 -mm
1500 psi +$ 0.00 V Viton +$ 2.00
D
G 12,7 mm dia.$ 51.80
50 GPM H
K Calibrated
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
Handknob with NFDD
I
E 17,5 mm dia.$ 97.30
100 GPM Detent Lock N 12,7
G 60 - 800
mmpsi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
F 21,6 mm dia. K Handknob NFED
W 17,5
H 150 -mm
4500 psi +$ 0.00
NFFDOptions:
Adjustment Range
IA, B,
21,6
C, mm
and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
NCBB 3000
NCCB 3000
NCEB 3000
NCFB
3000
2000
3000
NCGB
2000 2000 2000 2000
1000 1000 Adjustment Sensitivity at 7 bar Differential
1000 1000 1000
20 0 5 10 15 20 25 20 0 10 20 30 40 50 50 0 20 40 60 80 100 120 0 40 80 120 160 200 210 0 80 160 240 320 400
Flow = GPM Flow = GPM
Q = L/min.
Q = L/min.
Q = L/min.
Q = L/min.
15 15 38 90 156
10
■ Maximum
10 operating pressure25 = 5000 psi 60 105
0 1 2 3 4
■
5 Back0 pressure
1 2 on
3 the4 tank
5 port0(port
1 2)2 is directly
3 4 5additive0 at 1a 1:1
2 ratio
3 to
4 the
5 valve 0setting.
1 2 3 4 5
Number of Turns■ Number of Turns Number of Turns Number of Turns Number of Turns
Factory pressure settings established at 4 GPM
■ Typical response time 10 ms.
■ Maximum operating pressure = 350 bar
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Maximum
in valve
3/min./1000 psi,leakage
RPKC:=50,4 cc/min.
in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
NC ✱RP
✱ ✱ –C –✱✱C ✱ ✱
Maximum Nominal
Capacity Control** Adjustment Range Seal
Nominal Version Control** Cracking Pressure* Seal
Orifice C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
NCBB* 4,0 mm dia.E $ 36.20
25 GPMB High Capacity C Tamper Resistant
L +$ 4.10Screw
Standard B 50 - 1500 psi +$ 0.00
A 0,3 bar V Viton +$ 2.00
N Buna-N
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 *Cracking Pressure Ranges:
US Shortcut Catalogue #999-901-243
** See page 162 for information A and E ranges are not available
on Control Options in T-162A cavity.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
12
3000 30
3000 60
3000 100
3000 240
3000
10 25 50 84 200
Q = L/min.
2000
Q = L/min.
Q = L/min.
Q = L/min.
Q = L/min.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
FX ✱ C
A – ✱ ✱
A✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
B C 0,4-12 L/min. $ 31.90
12 GPM* LX Standard Screw +$ 0.00
Non-adjustable A
A 100
Fixed- 3000 psi +$ 0.00 N
Orifice Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 Factory Resistant
C Tamper set +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 0,4-25 L/min. at customer Customer must specify flow V Viton
G 50 GPM $ 51.80 K Handknob
specified flow +$ 5.00 C 150 - 6000 psi +$ 2.00
D I 0,4-50
100 L/min.
GPM $ 97.30 N 60 - 800 psi +$ 1.00
L Tuning Adjustment
E K 0,8-100 L/min. $187.00
200 GPM ±25% of customer Q 60 - 400 psi +$ 1.00
specified flow
F 0,8-200 L/min. W 150 - 4500 psi +$ 0.00
K Handknob with
L control Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
** See page 162 for information
on Control Options
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
L Control 2 1
c
X Control
b c
b 1
Locating
Shoulder
Locating Cartridge Dimensions
Shoulder
Typical Cartridge Dimensionsc Installation
Capacity Cartridge Cavity a b Torque
Nominal Model
Typical
Code L cC K Installation
(lb. ft.)
Cartridge Cavity a b Torque
a Capacity
12 GPM RPCC – LAN
Model Code T - 162A 1.22 3/4” X
2.11 L
2.17 K
2.31 (Nm)
25/30
a
2 0,4-12
25 GPM FCBB
L/min. RPEC – XAN T - T10A
– LAN - 162A 31
1.56 19,1
7/8” 21
2.00 54
2.06 58
2.25 35/40
30/35
2
Outlet
Port 0,4-25
50 GPM FCCB
L/min. RPGC – XAN T - T3A
– LAN - 13A 34,9
1.88 122,2
1/8” 19
2.12 51
2.18 58
2.38 40/50
45/50
0,4-50
100 GPM FCDB
L/min. RPIC – XAN T - T16A
– LAN - 5A 41,1
2.44 128,6
1/4” 18
2.44 54
2.47 61
2.69 60/70
150/160
Inlet 1
Port 1 0,8-100
200 GPML/min. FCEB –
RPKC – LANXAN T - 18A16A
T - 61,9
3.13 31,8
1 5/8” 25
2.81 62
2.94 69
3.06 200/215
350/375
0,8-200 L/min. FCFB – XAN T - 18A 79,4 41,3 31 72 78 465/500
Performance Curves
Performance Curves
RPCC RPEC RPGC RPIC RPKC
FCBB FCCB FCDB
Typical Pressure Rise
FCEB FCFB
5000 5000 Reverse Free Flow Pressure
5000 Drop Based on Specified
5000Flow Extremes 5000
4000 4000 4000 4000
P = psi
4000
20 20 10 10 14
P = psi
P = psi
P = psi
P = psi
3000
16 3000
16 3000
8 3000
8 3000
12
P = bar
P = bar
P = bar
P = bar
P = bar
2000 2000 2000 2000
6 2000
12 12 6 9
0,4 L/min. 0,4 L/min. 0,4 L/min. 0,8 L/min. 0,8 L/min.
1000
8 1000 1000
4 1000
4 1000
6
8
12 L/min.
4 0 5 10 15 20 25 4 0 10 20 30 40 50 2 0 20 40 60 80 100 2 0 40 80 120 160 200 3 0 80 160 240 320 400
23 L/min. 45 L/min. 95 L/min. 200 L/min.
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
0 20 40 60 80 0 10 20 30 40 0 20 40 60 80 0 40 80 120 160 0 80 160 240 320
Q = L/min. ■ MaximumQoperating
= L/min. pressure = 5000Q psi
= L/min. Q = L/min. Q = L/min.
■ Will accept maximum pressure at Port 2.
■
■ Maximum operating
Back pressure on thepressure
tank port=(port
350 bar
2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Customer must specify flow setting
Factory pressure settings established at 4 GPM
■
■ Accurate pressuretime
Typical response compensated
10 ms. control requires that a 14 bar minimum pressure differential be
maintained across the valve.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ The tuneable control
in3/min./1000 option5 provides
psi, RPKC: +/- 25%
in3/min./1000 psi.variation from the nominal factory pre-set flow.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ B
FC C – ✱ A
✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Adjustment Range Seal
Seal
Capacity
B C L/min. $ 31.90
12 GPM*
0,4-12 L Non-adjustable
X Standard Screw +$ 0.00 A Fixed
A 100 - 3000 psi +$ 0.00
Orifice N
N Buna-N +$ 0.00
Buna-N
E 25 GPM $ 36.20 C Factory Resistant +$ 4.10
Tamper set B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 0,4-25 L/min. at customer Customer must specify flow V Viton
G 50 GPM $ 51.80 K specified
Handknobflow +$ 5.00 C 150 - 6000 psi +$ 2.00
D I 0,4-50 L/min. $ 97.30
100 GPM N 60 - 800 psi +$ 1.00
L Tuning Adjustment
E K 0,8-100 L/min.$187.00
200 GPM ±25% of customer Q 60 - 400 psi +$ 1.00
specified flow
F 0,8-200 L/min. W 150 - 4500 psi +$ 0.00
K Handknob with
L control Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
** See page 162 for information
on Control Options
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
US Shortcut Catalogue #999-901-243
4000
P = psi
P = psi
P = psi
P = psi
Q = L/min.
Q = L/min.
Q = L/min.
25 50 100 0 40 80 120 200160 200
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 80 160 240 320 400
Flow = GPM
20
Flow = GPM
40 Flow = GPM 80 Flow = GPM 160 Flow = GPM
15 30 60 120
10 ■ Maximum operating 20 pressure = 5000 psi 40 80
5 10 20 40
■ Will accept maximum pressure at Port 2.
0 50 150 250 350 0 50 150 250 350 0 50 150 250 350 0 50 150 250 350
■ PBack
= bar pressure on the tank Pport= bar(port 2) is directly additive P = bar
P = barat a 1:1 ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■
■ Maximum
Typical operating
response timepressure
10 ms. = 350 bar
■
■ Accurate pressure compensated
Maximum leakage = RPCC, RPEC: control
2 inrequires
3/min./1000that psi,
a 14RPGC:
bar minimum pressure psi,
3 in3/min./1000 differential
RPIC: 4be
maintained
in 3/min./1000 across the valve.
psi, RPKC: 5 in3/min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱C
FD ✱ ✱ –
– ✱
✱ ✱
A✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Flow Control** Adjustment Range Seal
C Range
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E
BA 25 GPM
0,4-23 L/min.$ 36.20 C
L Tamper Screw +$ 4.10
StandardResistant B 50 - 1500 psi
FDBA +$ 0.00 V Buna-N +$ 2.00
N Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 A 150
C 0,4 -- 23 L/min.
6000 psi +$ 2.00
CB 0,4-45 L/min. H Calibrated V Viton
I 100 GPM $ 97.30 Handknob with N 60 - 800 psi
FDCB +$ 1.00
EA
K 1-95GPM
200 L/min. $187.00 Detent Lock A 60
Q 0,4--400
45 L/min.
psi +$ 1.00
FA 1-200 L/min. K Handknob W 150 - 4500FDEA
psi +$ 0.00
A 1 - 95 L/min.
Adjustment Range
FDFA Options:
A B,1 C,
A, andL/min.
- 200 W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
2 1
b
cc
b Locating
Shoulder
Locating 1
Shoulder
Cartridge Dimensions
Typical c Installation
Capacity Cartridge Cavity a b Torque
a Model Code CartridgeL Dimensions
C K (lb. ft.)
2 a
Nominal RPCC – LAN
12 GPM TypicalT - 162A
Cartridge Cavity
1.22 3/4”
a
2.11
b
2.17 c 2.31 Installation
25/30
Torque
2
Outlet Capacity RPEC – LAN
25 GPM T - 10A 1.56 7/8” 2.00 2.06 X 2.25 30/35
Outlet Model Code (Nm)
30 L/min. RPGC –CNAC
50 GPM LAN – XCNT - 3A 1.88
T - 162A 1 1/8”
31 2.12
19,1 2.18 21 2.38 45/50
35/40
60 L/min. RPIC –CNCC
100 GPM LAN – XCN
T - 16A 2.44
T - 13A 1 1/4”
34,9 2.44
22,2 2.47 19 2.69 150/160
40/50
Inlet 1
Inlet 1 200 120
GPM L/min.RPKC – LAN
CNEC – XCN- 18A
T 3.13
T - 5A 1 5/8”
41,1 2.81
28,6 2.94 18 3.06 350/375
60/70
Performance Curves 240 L/min. CNGC – XCN T - 16A 61,9 31,8 25 200/215
RPCC RPEC 480 L/min. CNIC
RPGC– XCN T - 18A RPIC
79,4 41,3 RPKC
31 465/500
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
P = bar
P = bar
0 10 20 30 ■
40 Will0 accept
20 maximum
40 60 pressure0 at Port
80 30 2.
60 90 120 0 80 160 240 320 0 160 320 480 640
Q = L/min. ■ Back pressure on the tank port (port Q2)= L/min.
Q = L/min. is directly additive at aQ1:1
= L/min. Q = L/min.
ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Maximum operating pressure = 350 bar
■ Typical response time 10 ms.
■ Will accept 350 bar at ports 1 and 2.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ * in
Orifice range =psi,
3/min./1000 CNAC,
RPKC: CNCC: 0,4 - 1,6 mm,
5 in3/min./1000 psi.CNEC: 0,4 - 2,0 mm, CNGC: 0,4 - 2,4 mm,
■ CNIC: minimum
RPCC 0,4 - 3,2 mm. setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
CN RP
✱ ✱C C– –
✱ ✱
✱ ✱
✱✱
Nominal
Control** Adjustment Range Seal
Nominal
Capacity
Control** Cracking Pressure Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 25
E 30 GPM
L/min. $ 36.20 X Tamper
C Non-adjustable
Resistant +$ 4.10 A 50
B 0,3-bar
1500 psi +$ 0.00 N Viton
V Buna-N +$ 2.00
C
G 60 GPM
50 L/min. $ 51.80 K Handknob +$ 5.00 B 150
C 1,0 bar
- 6000 psi +$ 2.00 V Viton
IE 120 GPM
100 L/min. $ 97.30 C 60
N 2,0-bar
800 psi +$ 1.00
G
K L/min. $187.00
240 GPM
200 D 60
Q 3,5-bar
400 psi +$ 1.00
I 480 L/min. E 150
W 5,0 bar
- 4500 psi +$ 0.00
F 7,0 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Performance Curves
1 Inlet
RPCC RPEC RPGC RPIC RPKC
Performance Curves Typical Pressure Rise
5000 5000 5000 5000
FPCC
5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
% Command
% Command
100% 100% 100%
0 5 10 15 20 25 "C" Spool 0 10 20 30 40 50 0 20 40 30,060 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Q = L/min.
Q = L/min.
Q = L/min.
Q = L/min.
20,0
Flow = GPM 10,0Flow = GPM 75% Flow = GPM Flow
75% = GPM
40,0 Flow = GPM75%
"B" Spool 20,0
50% 50% 50%
10,0 Maximum
■ 5,0 operating pressure = 5000 psi
10,0
20,0
"A" Spool 25% 25% 25%
0 20 40 60
■
80 100
Will accept0 maximum100 200
pressure
300 344
at Port 2. 0 100 200 300 344 0 100 200 300 344
% Command ■ Back pressure on Pthe = bar P = bar
tank port (port 2) is directly additive at a 1:1 ratio to the valve Psetting.
= bar
■ Factory pressure settings established at 4 GPM
■ Maximum operating pressure = 350 bar
■ Typical response time 10 ms.
■ Maximum valve leakage = 100 cc/min. at3 210 bar
■ Maximum leakage = RPCC, RPEC: 2 in /min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ For optimum performance,
in3/min./1000 psi, RPKC: 5an in3amplifier
/min./1000withpsi.current sensing and adjustable dither should be used.
Dither should be adjustable between 100 - 250 Hz.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱C – ✱ ✱ ✱
FP C
Nominal
Maximum
Capacity Control** Adjustment Range Seal
Nominal Control** Nominal Capacity Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E
C 25 L/min.
28 GPM $ 36.20 C Manual
M Resistant +$ 4.10
Tamper Override B 650L/min.
A - 1500 psi +$ 0.00 V Buna-N
N Viton +$ 2.00
(Standard)
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
B 14 L/min. V Viton
I 100 GPM $ 97.30 NOTE: Coil must be N 60 - 800 psi +$ 1.00
ordered separately. Use C 28 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
12V DC or 24V DC
(Series 770-***) coils
W 150 - 4500 psi +$ 0.00
only. See page 167.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
1 InletCurves
Performance
RPCC RPEC RPGC RPIC RPKC
Performance Curves Typical Pressure Rise
5000 5000 5000 FPCH 5000 5000
4000 4000 4000 4000
P = psi
4000
Flow vs. Command Flow vs. Pressure3000
Differential
P = psi
P = psi
P = psi
P = psi
% Command
% Command
Flow = GPM
"C" Spool 0% 0%
Q = L/min.
Q = L/min.
Q = L/min.
15,0 15,0 20,0
0 5 10 15 20 25 0 10,0
10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
25% 25% 25%
10,0 Flow = GPM
"B" Spool
Flow = GPM Flow10,0
= GPM Flow = GPM 10,0 Flow = GPM
5,0 50% 50% 50%
5,0 "A" Spool 5,0
■ Maximum operating pressure = 75%5000 psi 75% 75%
0 20 40 60 ■
80 100Will accept
0 maximum
100 pressure
200 344 at Port 2. 0 100 200 344 0 100 200 344
% Command P = bar P = bar P = bar
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Maximum operating pressure = 350 bar
■ Typical response time 10 ms.
■ Maximum valve leakage = 100 cc/min. at3 210 bar
■ Maximum leakage = RPCC, RPEC: 2 in /min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ For optimum performance,
in3/min./1000 psi, RPKC: 5an in3amplifier
/min./1000withpsi.current sensing and adjustable dither should be used.
Dither should be adjustable between 100 - 250 Hz.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
FP C
✱HC – ✱ ✱✱
Nominal
Maximum
Capacity Control** Adjustment Range Seal
Nominal Control** Nominal Capacity Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 28 L/min. D Manual Override A 6 L/min. N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
(Standard)
G 50 GPM $ 51.80 K Handknob +$ 5.00 B
C 14
150L/min.
- 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
ordered separately. Use C 20 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
1 3
2
Bypass / Restrictive, Fixed Orifice 76
1 3
2 Ventable, Bypass / Restrictive, Fixed Orifice 77
T-8A
4
3
1 Ventable, Bypass / Restrictive, Fixed Orifice with
2 78
Integral Pilot Control Cavity
b
3 Locating
Priority Locating
Shoulder Cartridge Dimensions
Flow Shoulder Typical Cartridge Dimensions
c Installation
Capacity Cartridge
Typical Cavity a b c Torque
Installation
Capacity Cartridge Code
Model Cavity a b X L K (Nm)
Torque
a L C K
2 0,4-12 L/min. Model Code– XAN
FRBA T - 163A 31 19,1 32 43 47 (lb. ft.)
35/40
Bypass a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Flow 0,4-25 L/min. FRCA – XAN T - 11A 34,9 22,2 31 64 71 40/50
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 0,4-50 L/min. FRDA – XAN T - 2A 34,9 28,6 35 72 78 60/70
Inlet 1 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
0,8-100 L/min. FREA – XAN T - 17A 46 31,8 46 84 91 200/215
0,8-200 L/min.RPIC – LAN
100 GPM T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 FRFA – XAN T - 19A 63,5 41,3 60 100 107 465/500
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
FRBA FRCA FRDA FREA FRFA
RPCC RPEC RPGC RPIC RPKC
Typical Performance
Factory Inlet (L/min.) Factory Inlet (L/min.) Typical
Factory PressureInlet
Rise(L/min.) Factory Inlet (L/min.) Factory Inlet (L/min.)
Priority Flow (L/min.)
psi (L/min.)
P = psi
P = psi
12 15 12 20 24 40 45 80 120 160
30008 Valve Set @ 12 L/min. 3000 Valve Set @ 12 L/min. 3000
Valve Set @ 24 L/min. 3000
Valve Set @ 45 L/min. 3000
Valve Set @ 120 L/min.
8 16 30 20
32* 60* 120* 240*
Priority
2000 480*
20004
Valve Set @ 4 L/min. 15
2000
4
Valve Set @ 4 L/min. 20
2000
8 Valve Set @ 8 L/min. 40 15 Valve Set @ 15 L/min. 80 10 2000
Valve Set @ 40 L/min. 160
10000 0
1000 1000
0 01000 0 1000
350 210 70 0 70 210 350 350 210 70 0 70 210 350 350 210 70 0 70 210 350 350 210 70 0 70 210 350 70 0 70 210 350 350 210
Bypass
0 pressure5 P 10 = bar15
Priority 20
pressure
25 Bypass pressure
0 10 P =20 bar Priority
30 pressure
40 50 0
Bypass pressure 20P = bar
40 Priority
60 pressure 0
80 100 Bypass pressure 40= bar
P 80 Priority
120pressure
160 200 Bypass pressure
0 P80= bar
160 240
Priority 320 400
pressure
higher than priority higher than bypass
Flow = GPM
higher than priority higher than bypass
Flow = GPM higher than priority Flow =higher
GPM than bypass higher than priority Flowhigher
= GPM than bypass higher than priority higher than bypass
Flow = GPM
■
■ Maximum operating
Maximum operating pressure
pressure == 350
5000barpsi
■
■ Will accept maximum pressure at Port
Customer must specify a flow rating. Factory 2. set flow ratings are within +/- 10% of the
■ requested setting.
Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Pressure at the bypass
Factory pressure portestablished
settings (port 2) may at 4exceed
GPM pressure at the priority port (port 3).
■
■ Maximum pressure
Typical response at port
time 3 should be limited to 210 bar.
10 ms.
■
■ Both priority
Maximum and bypass
leakage = RPCC,flowRPEC:
are usable
2 in 3up to the system
/min./1000 operating
psi, RPGC: 3 inpressure.
3/min./1000 psi, RPIC: 4
3
in /min./1000 3
■ Bypass flow ispsi,
not RPKC:
available5 in /min./1000
until psi. requirements are satisfied.
priority flow
■
■ RPCC minimum
Blocking priority setting foralso
flow will all spring
block ranges
bypass is 75 psi
flow.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ A
FR C – ✱ A
✱✱
Nominal
Control** Adjustment Range Seal
Capacity
C 0,4-12
B L/min. $ 31.90
12 GPM* L Non-adjustable
X Standard Screw +$ 0.00 A Fixed
A 100 - 3000 psi
Orifice +$ 0.00 N Buna-N
N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Tamper set
Factory Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 0,4-25 L/min. at customer Customer must specify flow V Viton
G 50 GPM $ 51.80 K specified
Handknobflow +$ 5.00 C 150 - 6000 psi +$ 2.00
D 0,4-50 L/min.
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
L Tuning Adjustment
E
K 0,8-100 L/min.$187.00
200 GPM ±25% of customer Q 60 - 400 psi +$ 1.00
specified flow
F 0,8-200 L/min. W 150 - 4500 psi +$ 0.00
K Handknob for
L control
Adjustment Range Options:
Maximum Inlet Flow: Priority
A, B, C, Flow
and Wranges:
are standard set at 1000 psi.
FRBA: 30 L/min. FRBA:
N Option0,4is- standard
12 L/min.set at 400 psi.
FRCA: 60 L/min. FRCA:0,4
Q Option is- 25 L/min.set at 200 psi.
standard
FRDA: 120 L/min. ** See page 162 for information FRDA:0,4
* Minimum- setting
50 L/min.
75 psi on all ranges.
FREA: 240 L/min. ** See page 162
on Control for information
Options FREA:
Customer0,8 -may
100 specify
L/min. pressure setting. +$ 1.10
FRFA: 480 L/min. on Control Options FRFA: 0,8 - 200 L/min.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
76 UK Shortcut Catalogue #999-901-244
Priority Flow Control Valves
VENTABLE, BYPASS / RESTRICTIVE, FIXED ORIFICE
4
Relief Valves
3
PILOT
b OPERATED,1 BALANCED
2 PISTON
Full Adjustment 5 Turns
4
+ - c
Vent
3 2 1
Locating
Priority
Flow c Shoulder Cartridge Dimensions
Typical c Installation
b
2 a Capacity Cartridge
Model Code
Cavity a b
X L K
Torque
(Nm)
Bypass Locating
Flow Shoulder 0,4-25 L/min. FVCA – XAN T - 21A 34,9 22,2 46 79 86 40/50
Cartridge Dimensions
0,4-50 L/min. FVDA – XAN T - 22A 34,9 28,6 51 88 94 60/70
Inlet 1 Typical c Installation
Capacity
0,8-100 L/min. FVEA – XAN
Cartridge Cavity
T - 23A a 46 b
31,8 66
L 100
C 107K Torque
200/215
Model Code (lb. ft.)
a 0,8-200
12 GPM FVFA
L/min.RPCC – XAN T - T162A
– LAN - 24A 1.2263,5 41,3
3/4” 81
2.11 121
2.17 128
2.31 465/500
25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Performance Curves 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 FVCA FVDA FVEA FVFA
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Typical Performance
Performance Curves Factory Inlet (L/min.) Factory Inlet (L/min.) Factory Inlet (L/min.) Factory Inlet (L/min.)
Priority Flow (L/min.)
P = psi
Bypass pressure Priority pressure Bypass pressure Priority pressure
P = psi
P = psi
higher than priority higher than bypass higher than priority higher than bypass higher than priority higher than bypass higher than priority higher than bypass
3000 3000 3000 3000 3000
2000 2000 2000 2000 2000
1000 ■ Maximum
1000 operating pressure = 350 bar
1000 1000 1000
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
FV ✱ C
A – ✱ ✱
A✱
Nominal
Nominal
Capacity Control**
Control** Adjustment RangeRange
Adjustment Seal Seal
Capacity
C C L/min.
0,4-25 12 GPM* $ 31.90X L Standard Screw
Non-adjustable factory+$
set 0.00 A 100
A- 3000
Fixedpsi +$ 0.00
Orifice N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 at
C customer specified flow
Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
D 0,4-50 L/min. Customer must specify flow V Viton
G 50 GPM $ 51.80L K Handknob
Tuning Adjustment ±25%+$ 5.00 C 150 - 6000 psi +$ 2.00
E 0,8-100 L/min. of customer specified flow
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
F 0,8-200
K L/min.
200 GPM $187.00K Handknob Q 60 - 400 psi +$ 1.00
(includes L controls)
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
UK Shortcut Catalogue #999-901-244 77
Priority Flow Control Valves
VENTABLE, BYPASS / RESTRICTIVE, FIXED ORIFICE WITH INTEGRAL
PILOT CONTROL CAVITY
4
Relief Valves The -8 control option allows the pilot control valve to be incorporated directly
into the end of the priority flow control cartridge via the T-8A cavity. These pilot
T-8A
3
PILOT
b OPERATED,1 BALANCED
2
PISTON
control cartridges are sold separately and include electro-proportional, solenoid,
air pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
Full Adjustment 5 Turns
4 + - c
Vent
3
Locating 2 1 Cartridge Dimensions
Priority Shoulder
Flow Typical c Installation
c Capacity Cartridge Cavity a b Torque
Model Code 8 (Nm)
b2 a 0,4-25 L/min. FVCA – 8AN T - 21A 34,9 22,2 46 40/50
Bypass
Flow Locating 0,4-50 L/min. FVDA – 8AN T - 22A 34,9 28,6 46 40/50
Shoulder
0,8-100 L/min. FVEA – 8AN T - 23A 46 Cartridge Dimensions46
31,8 40/50
Inlet 1 Typical c Installation
Capacity FVFA – 8AN Cavity T - 24A a
0,8-200 L/min. Cartridge 63.5 b 41,3 46 40/50Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Performance
2 Curves
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet FVCA-8 50 GPM FVDA-8
RPGC – LAN
FVEA-8 1.88
T - 3A 1 1/8” FVFA-8
2.12 2.18 2.38 45/50
100 GPM TypicalTPerformance
RPIC – LAN - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 Factory Inlet (L/min.)
200 GPM RPKC
Set Point – LAN
Factory Inlet (L/min.)
T - 18A SetFactory 3.13 Inlet (L/min.)
1 5/8” Factory
2.81 Inlet (L/min.)
2.94 3.06 350/375
Priority Flow (L/min.)
4000
P = psi
P = psi
P = psi
P = psi
3000
■ Maximum
3000 operating pressure3000= 350 bar 3000 3000
2000 ■ Nominal
2000 vent flow = 0,75 L/min. 2000 2000 2000
1000
1000 ■ Pressure
1000
at the bypass port (port 1000
2) may exceed pressure at the priority port (port 1000
3).
0 5 10
Flow = GPM
15 20 ■ 25
Maximum 0 10
pressure
20 30
Flow = GPM
at
40
port
50
3 should
0 20
be limited
40
Flow =
60
GPM
to 210
80 100
bar. 0 40 80
Flow =
120
GPM
160 200 0 80 160 240
Flow = GPM
320 400
■ Both priority and bypass flow are usable up to the system operating pressure.
■
■ Maximum
Bypass flowoperating pressureuntil
is not available = 5000 psi flow requirements are satisfied, except when the valve is
priority
■ Will accept
vented. When maximum pressure
port 4 (vent) is open,at Port 2. diverts to port 2 if pressure at port 1 (inlet) is 10,5 bar
all flow
■ or
Backhigher.
pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Using
Factory a pressure
pressure control
settingson port 4 willatlimit
established 4 GPM the pressure at the priority port (port 3). If pressure on the
■ bypass
Typicalport (port 2)
response timeexceeds
10 ms.the setting of the pressure control, priority flow will be shut off and all the
flow will go out the bypass port.
■
■
Maximumpriority
Blocking leakageflow = RPCC, RPEC:
will also in 3/min./1000
block2 bypass
3
flow. psi, RPGC: 3 in /min./1000 psi, RPIC: 4
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ The main stage valve should first be installed to the correct torque value followed by the T-8A pilot
■ RPCC minimum
control section into setting for all
the main spring
stage valveranges
to itsisrequired
75 psi torque value.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
FVRP
✱✱A C– –8 ✱A ✱
✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal Seal
Capacity
C 0,4-25
C L/min.
12 GPM* $ 31.908 T-8A cavity inScrew
L Standard hex body+$ 0.00 A - 3000
A 100 Fixedpsi
Orifice
+$ 0.00 N Buna-N
N Buna-N +$ 0.00
for pilot operation (Pilot
D E L/min.
0,4-50 25 GPM $ 36.20 C Tamper Resistant
valve to be ordered +$ 4.10 B 50 - 1500 psi
Customer +$ 0.00
must V VitonV
specify flow +$ 2.00
Viton
separately)
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
E 0,8-100 L/min.
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
F 0,8-200 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
78 UK Shortcut Catalogue #999-901-244
6 US Shortcut Catalogue #999-901-243
Relief Valves
PILOT OPERATED, BALANCED PISTON
Full Adjustment 5 Turns
+ -
2 1
c
b
Priority Flow Control
Locating Valves
Shoulder
BYPASS / RESTRICTIVE MODULATING
Typical
ELEMENT Cartridge Dimensions
c Installation
Capacity Cartridge Cavity a b Torque
b Model Code L C K (lb. ft.)
3
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 c 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN
1 T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Locating
Shoulder 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
4 2
Performance
4
Curves
RPCC
Port RPEC RPGC RPIC RPKC
Cartridge Dimensions
a Typical Pressure Rise
3 Typical c Installation
5000 5000 Capacity Cartridge
5000 Cavity 5000 a b 5000 Torque
Port 4000 Model Code
4000 4000 X4000 (Nm)
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 3000
LHDA – XFN
3000 3000 3000
60 L/min. T - 31A 2000
84,8 22,2 30 40/50
2000 2000 2000 2000
2
1000 1000 120 L/min. LHFA1000– XFN T - 32A 1000 92,2 28,6 34
1000 60/70
Port
0 5 10 15 20 25 0 10
240 20 30
L/min.
Flow = GPM
40
LHHA –0 XFN
50 20 40 60
Flow = GPM
T 80 100
- 33A 0 40
114,4 80 120 160
31,8
Flow = GPM
200
42 0 80 160 240
200/215
Flow = GPM
320 400
Flow = GPM
480 L/min. LHJA – XFN T - 34A 139,7 41,3 51 465/500
1 Port
■ Maximum operating pressure = 5000 psi
■ Will accept maximum pressure at Port 2.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory
Maximum pressure settings
operating established
pressure at 4 GPM
= 350 bar
■
■ Typical response
Bypass flow is nottime 10 ms.until priority flow requirements are satisfied.
available
Maximum leakage 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
■ Bypass pressure at = RPCC,
port 4 canRPEC: 2 inthan
be higher pressure at control port 2.
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Priority flow can be turned on or off with a pilot sized solenoid valve on port 1.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
LH ✱ C
A – ✱
X ✱✱
Maximum
Nominal
Control** Adjustment Range Seal
Capacity
Inlet Flow
C
D 6012 GPM*
L/min. $ 31.90 L
X Standard Screw
Non-adjustable +$ 0.00 A
E 100
5 - 7- bar
3000 psi +$ 0.00 N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 120 L/min. F 7 - 9,5 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
H 240 L/min.
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
J 480 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4
3
2
Divider 82
4
3 Divider / Combiner, Closed Centre 83
2
4
3 Synchronizing Divider / Combiner 84
2
12 L/min. 60 L/min.
Percentage of Flow
Percentage of Flow
Percentage of Flow
Port 4 Port 2 52,5 Port 4 Port 2 52,5 Port 2 53,5
50 50 50
Input Flow
Input Flow
Input Flow
RPIC – LAN
at Port 3
at Port 3
at Port 3
Port 2 Port 4 100 GPM
47,5 Port 2 T - 16A Port 4 2.44 47,5 1 1/4” 2.44Port 2 2.47 2.69
Port 4 150/160
46,5
Inlet Port14 Port 2
54,5
Port 4 Port 2
54,5
Port 4 Port 2
56,5
200 GPM
50 RPKC – LAN T - 18A 3.13 50 1 5/8” 2.81 2.94 3.06 350/375
50
Port 2 Port 4 45,5 Port 2 Port 4 45,5 Port 2 Port 4 43,5
Performance
350 280 210 Curves
140 70 0 70 140 210 280 350 350 280 210 140 70 0 70 140 210 280 350 350 280 210 140 70 0 70 140 210 280 350
Port 4 > Port 2 Differential Port 2 > Port 4 Port 4 > Port 2 Differential Port 2 > Port 4 Port 4 > Port 2 Differential Port 2 > Port 4
RPCC Pressure (bar) RPEC RPGCPressure (bar) RPIC RPKC
Pressure (bar)
FSED-XAN FSFD-XAN
Typical Pressure Rise Port 4
45 L/min. 240 L/min.
23 L/min. 120 L/min.
Percentage of Flow
Percentage of Flow
P = psi
P = psi
P = psi
56,5 56,5
3000 3000 300050 3000 50 3000
Port 2 Port 4 43,5 Port 2 Port 4 43,5
2000 2000 2000 2000 2000
1000 350 1000
280 210 140 70 0 70 140 210 2801000
350 350 280 210 140 1000 0
70 70 140 210 280 350 1000
Port 4 > Port 2 Differential Port 2 > Port 4 Port 4 > Port 2 Differential Port 2 > Port 4
0 5 10 15 20 25 0 10 20 30 (bar)40 50 0 20 40 60 80 100 0
Pressure 40
(bar) 80 120 160 200 0 80 160 240 320 400
Pressure
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Maximum operating pressure = 350 bar
■ Maximum operating pressure = 5000 psi
■ This valve is a divider only; any attempt to flow backwards through the valve is not advised.
■ Will accept maximum pressure at Port 2.
■ Divisional accuracy at maximum rated input flow = FSBD: ±2.5%, FSCD, FSDD, FSED, FSFD: ±3.5%
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Divisional accuracy at minimum rated input flow = FSBD: ±4.5%, FSCD, FSDD, FSED, FSFD: ±6.5%
■ Factory pressure settings established at 4 GPM
■ Pressure drop at maximum input flow = 18 bar
■ Typical response time 10 ms.
■ Pressure drop at minimum input flow = 0,7 bar
■
■ Maximum
Below the leakage = flow
minimum RPCC, RPEC:
rating there in 3not
2 is /min./1000 psi, RPGC:
enough flow 3 in3/min./1000
for the valve psi,ItRPIC:
to modulate. 4
is effectively
3 3
in /min./1000 psi, RPKC: 5 in /min./1000 psi.
a tee. If flow starts at zero and rises, there will be no dividing control until the flow reaches the
■ RPCC minimum
minimum rating. setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱D
FS ✱ C –
– X
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Flow Proportion Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 2,5-12 L/min. X Non-adjustable A 50/50 Flow Split N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 6-30 L/min. B* 40/60 Flow Split V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
D 12-60 L/min. C* 33/67 Flow Split
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
E 23-120 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
F 45-240 L/min. * Port 4 is always high
W percentage
150 - 4500 flow.
psi +$ 0.00
Relief Valves
4
PILOT
Port OPERATED, BALANCED PISTON
Cartridge Dimensions
Full Adjustment 5aTurns
3 Capacity Typical Installation
+ - Cartridge Cavity a b c d Torque
Port Min/Max Model Code (Nm)
2,5-12 L/min. FSBA – XAN T - 31A 84,8 22,2 19 17 40/50
2
2 1
6-30 L/min. FSCA – XAN T - 31A 84,8 22,2 19 17 40/50
Port c
Working
12-60 L/min. FSDA – XAN T - 32A 92,2 28,6 18 20 60/70
b d Parts
Clearance
23-120 L/min. FSEA – XAN T - 33A 114,4 31,8 25 26 200/215
Port 1 Not Used Locating 45-240 L/min. FSFA – XAN T - 34A 139,7 41,3 31 30 465/500
Shoulder
Performance Curves Cartridge Dimensions
Typical c Installation
Capacity Operating Cavity
Cartridge Characteristicsa b Torque
Model Code L C K (lb. ft.)
FSBA-XAN
a 12 GPM RPCC – LAN FSCA-XAN
T - 162A 1.22 3/4” 2.11 FSDA-XAN
2.17 2.31 25/30
2,5 L/min. 12 L/min.
12 L/min. 60 L/min.
2
Percentage of Flow
Percentage of Flow
Percentage of Flow
Port 4 Port 2 Port 4 Port 2 Port 4 Port 2
RPEC – LAN
52,5 52,5 52,5
25 GPM
50 T - 10A 1.56 50 7/8” 2.00 2.06 2.25 30/35
50
Input Flow
Input Flow
Input Flow
Outlet
at Port 3
at Port 3
at Port 3
Port 2 Port 4
47,5 Port 2 Port 4
47,5 Port 2 Port 4 47,5
Port 4 Port 2 50 GPM
54,5
RPGC – LAN Port 4 T - 3A Port 2 1.88 54,5
1 1/8” 2.12 Port 4 2.18 2.38
Port 2 45/50
54,5
50 50 50
Port 2 Port 4 100 GPM
45,5 RPIC – LAN
Port 2 T - 16A Port 4 2.44 45,5 1 1/4” 2.44 Port 2 2.47 2.69
Port 4 150/160
45,5
Inlet 1
350 280 210 140 70 0 70 140 210 200350
280 GPM RPKC
350 –
280LAN
210 140 70 T -0 18A
70 140 210 3.13
280 350 1 5/8” 350 2.81210
280 140 2.94
70 0 70 3.06210
140 280 350/375
350
Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4
Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2
Performance Curves (bar) (bar) (bar)
FSEA-XAN FSFA-XAN
RPCC RPECPort 4 RPGC RPIC RPKC
45 L/min. 240 L/min.
23 L/min. 120 L/min.
Percentage of Flow
Percentage of Flow
at Port 3
at Port 3
4000
P = psi
P = psi
P = psi
P = psi
RP
FS ✱ C
A – ✱
X ✱
A✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Flow Proportion Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 2,5-12 L/min. X Non-adjustable A 50/50 Flow Split N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C
G 6-30
50 L/min. $ 51.80
GPM K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
12 L/min. 60 L/min.
Percentage of Flow
Percentage of Flow
Percentage of Flow
Port 4 Port 2 52,5 Port 2 Port 4 Port 2 52,5
50 50 50
Input Flow
Input Flow
at Port 3
Port 2 Port 4
47,5 Port 4 Port 2 Port 4 47,5
Inlet 1 Port 4 Port 2
54,5
Port 4 Port 2
54,5
Port 4 Port 2
54,5
200 GPM
50 RPKC – LAN T - 18A 3.1350 1 5/8” 2.81 2.94 3.06 50 350/375
Port 2 Port 4 45,5 Port 2 Port 4 45,5 Port 2 Port 4 45,5
Performance Curves
350 280 210 140 70 0 70 140 210 280 350 350 280 210 140 70 0 70 140 210 280 350 350 280 210 140 70 0 70 140 210 280 350
Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4
Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2
RPCC (bar) RPEC (bar) RPGC RPIC (bar) RPKC
FSES-XAN FSFS-XAN
45 L/min. 240 L/min.
Percentage of Flow
Percentage of Flow
at Port 3
at Port 3
4000 50
P = psi
50 P = psi
P = psi
FS ✱ C
RP S – ✱
X ✱
A✱
Nominal
Capacity Control**
Control Adjustment Range
Flow Proportion Seal
Capacity
C
B 2,5-12 L/min. $ 31.90
12 GPM* L
X Standard Screw
Non-adjustable +$ 0.00 A
A 100 - 3000
50/50 Split +$ 0.00
Flowpsi N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 6-30 L/min. V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
D 12-60 L/min.
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
E 23-120 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
F 45-240 L/min.
W 150 - 4500 psi +$ 0.00
Divisional Accuracy (Combining and Dividing) =
± 4.5 % at minimum input flow
± 2.5 % Range
Adjustment at maximum input flow
Options:
Synchronizing
A, B, C, and W Flow per Leg:set at 1000 psi.
are standard
N Option
FSBS: 0,6is- standard
1 L/min. set at 400 psi.
Q Option
FSCS: is -standard
0,75 2 L/min.set at 200 psi.
** See page 162 for information *FSDS:
Minimum
1,2 - setting 75 psi on all ranges.
2,5 L/min.
on Control Options Customer
FSES: 3 - 6may specify pressure setting.
L/min. +$ 1.10
FSFS: 9 - 13 L/min.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
84
6 UK Shortcut
US Shortcut Catalogue #999-901-243
#999-901-244
Flow Divider / Combiner Valves
HIGH CAPACITY DIVIDER / COMBINER, CLOSED CENTER
b
c 4 Note: Closed center valves have spring centered internal spools that provide
Locating 3 blocked flow paths when centered. Centering occurs when the Port 3 flow
Shoulder is also blocked. This internal blocking isolates Port 2 and 4 from cross flow.
2
Relief
4
Valves
PILOT
Port
OPERATED, BALANCED PISTON Cartridge Dimensions
3Full Adjustment 5 Turns
a Typical Installation
Capacity Cartridge Cavity a b c d Torque
Port + - Min/Max Model Code (Nm)
8-40 L/min. FSCH – XAN T - 31A 84,8 22,2 19 17 40/50
2 FSDH – XAN
215-80 L/min. 1 T - 32A 92,2 28,6 18 20 60/70
Port
c
Working
32-160 L/min. FSEH – XAN T - 33A 114,4 31,8 25 26 200/215
Parts
b
d
Clearance
60-320 L/min. FSFH – XAN T - 34A 139,7 41,3 31 30 465/500
Port 1 Not Used
Locating
Performance Curves Shoulder
Cartridge Dimensions
Constant Command - Varying Flow
Typical c Installation
Capacity Cartridge Cavity a b Torque
FSCH-XAN Model Code FSDH-XAN L C
FSEH-XAN K (lb. ft.)
a
RPCC – LAN
Percentage of Flow
Percentage of Flow
Percentage of Flow
Port 4 Port 4 Port 2
Port 2
12 GPM
54 T - 162A Port 2
1.22 54 3/4” 2.11 Port 4 2.17 2.31 25/30
54
50 50 50
Input Flow
Input Flow
Input Flow
2
at Port 3
at Port 3
at Port 3
46 46 46
Port 2
Port 4
Port 4
Port 2
25 GPM RPEC – LAN Port 2
Port 4
T - 10A Port 4
Port 2
1.56 7/8” Port 2
2.00 Port 4 2.06 Port 4
2.25 30/35
Outlet 56,5 56,5 Port 2
56,5
8 L/min.
Port 2 Port 4
50
50 GPM
43,5 RPGC – LAN
Port 2
T - 3A Port 4
1.88 50
43,5
1 1/8” 2.12 Port 2 2.18 2.38
Port 4
50
45/50
43,5
Percentage of Flow
Port 4 Port 2 54
50
Input Flow
at Port 3
4000
P = psi
P = psi
P = psi
P = psi
RP
FS ✱ C
H – ✱
X ✱
A✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Flow Proportion Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 8-40 L/min. X Non-adjustable A 50/50 Flow Split N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
D
G 15-80
50 GPML/min.$ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
IE 100 GPM
32-160 $ 97.30
L/min. N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
F 60-320 L/min.
W 150 - 4500 psi +$ 0.00
Adjustment
Divisional Accuracy Range Options:
(Combining and Dividing) =
± 6.5 % atA,minimum
B, C, andinput
W are standard set at 1000 psi.
flow
± 4.0 % at maximum input flowset at 400 psi.
N Option is standard
Q Option is standard set at 200 psi.
Visit www.sunhydraulics.com
** See pagefor
162detailed and complete *technical
for information Minimuminformation ononour
setting 75 psi all full line of products.
ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Flow Divider / Combiner Valves
NOTES
2 3
PILOT
b OPERATED, BALANCED PISTON 3
3 3 3
Full Adjustment 5 Turns
+ -
c
1 1 1 1 1
9
P = bar
P = bar
P = bar
12 12 12
6
8
Typical Pressure8 Rise 8
3 5000 4 5000 4 5000 4 5000
5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
0 5 10 15 20
■
25 Maximum
0 10 operating
20 30 40pressure
50 =0 35020 bar40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Area ratio: A3 to A1 = 1.8:1
■ Maximum operating pressure = 5000 psi
■ Area ratio: A3 to A2 = 2.25:1
■ Will accept maximum pressure at Port 2.
■ Control orifice diameter = LODA, LODB, LODD, LOFA, LOFB, LOFD: 0,53 mm, LOHA, LOHB,
■ Back pressure
LOHD: 0,8 mm, onLOJA,
the tank port (port
LOJB, LOJD: 2) 0,9
is directly
mm. additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure settings established at 4 GPM
Pilot volume for complete shift = LOD*: 0,6 c.c., LOF*: 1,1 c.c., LOH*: 4,1 c.c., LOJ*: 6,9 c.c.
■ Typical response time 10 ms.
■ These valves are pressure responsive at all three ports, therefore it is essential to consider all aspects of
■ Maximum
system leakagethrough
operation = RPCC,a RPEC: 2cycle.
complete in 3/min./1000
Pressure psi, RPGC:
changes at any
3/min./1000 psi, RPIC: 4
3 inone port may cause a valve to
in3/min./1000
switch psi, RPKC:
from a closed in3/min./1000
to an 5open position, orpsi.vice versa. All possible pressure changes in the complete
■ RPCC must
circuit minimum setting fortoall
be considered spring
assure ranges
a safe, is 75 psi system design.
functional
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
LO ✱RP
✱ ✱ –C –✱✱✱ ✱
✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range Cracking Pressure
Seal
Version Control** A, B, C, D Versions Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 80 L/min. A Spring biased closed X Non-adjustable D 3,5 bar at Port 1 N Buna-N
E $ 136.20
25 GPM Port C Tamper Resistant +$ 4.10
pilot source B 50 - 1500 psi +$ (2
0.00
bar to V Viton
close +$ 2.00
F 160 L/min. G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ at2.00
Port 3 for V Viton
B Spring biased closed Available in B and C O Version)
H 320 L/min. I $ 297.30
100 GPM Port pilot source VersionsNOnly
60 - 800 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
88 UK Shortcut Catalogue #999-901-244
Logic Elements
UNBALANCED POPPET, PILOT-TO-CLOSE SWITCHING ELEMENT WITH
INTEGRAL PILOT CONTROL CAVITY
Relief Valves
2 3 2 3
The -8 control option allows a
2 3
PILOT OPERATED, BALANCED PISTON pilot control valve to be incorporated
directly into the end of the cartridge via
b Full Adjustment 5 Turns T-8A T-8A T-8A
the T-8A cavity. These pilot control
Cav Cav Cav cartridges are sold separately and
+ -
include solenoid and air pilot operation.
c 1 1 See Pilot Control Cartridges on
1
3 page 121.
2 LO*A-8 1 LO*B-8 LO*D-8
Port Locating
c
Shoulder
b Cartridge Dimensions
2 Nominal Typical Installation
a Locating Cartridge Cavity a b c Torque
Port Shoulder Capacity Model Code (Nm)
Cartridge Dimensions
80 L/min. LODA – 8DN
Typical T - 11A 34,9 22,2 c 28 40/50
Installation
1 Port Capacity
160 L/min. Cartridge
LOFA – 8DN Cavity T - 2A a 34,9 b 28,6 Torque
Model Code L C 35 K 60/70
(lb. ft.)
a 320
12 GPM LOHA
L/min. RPCC – 8DN T - 162A
– LAN T - 17A1.22 46 3/4” 31,8
2.11 2.17 46 2.31 200/215
25/30
2 640
25 GPM LOJA
L/min. RPEC – 8DN T - 10AT - 19A1.56
– LAN 63,57/8” 41,3
2.00 2.06 59 2.25 465/500
30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance Curves
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
LOD*-8 200 GPMLOF*-8
RPKC – LAN LOH*-8 3.13
T - 18A 1 5/8” LOJ*-8
2.81 2.94 3.06 350/375
9
P = bar
P = bar
P = bar
6
12 Typical Pressure
12 Rise 12
8 8 8
5000 5000 5000 5000 5000
3 4 4 4
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
0 5 10 15 20
■
25 Maximum0 10 operating
20 30 pressure
40 50 = 350
0 bar 40 60 80 100
20 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM
Flow = GPM ■ Area ratio:Flow
A3 =toGPM
A1 = 1.8:1
■
■ Maximum
Area ratio: A3operating
to A2 =pressure
2.25:1 = 5000 psi
■ Will
Control orifice diameterpressure
accept maximum = LOD*-8, at Port
LOD*-8,2. LOF*-8, LOF*-8: 0,53 mm, LOH*-8, LOH*-8:
■ 0,8 mm,
Back LOJ*-8,
pressure onLOJ*-8:
the tank0,9 mm.
port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ These valves
Factory are pressure
pressure settings responsive
establishedatatall4three
GPMports, therefore it is essential to consider all aspects of
system operation through a complete cycle. Pressure changes at any one port may cause a valve to
■ Typical
switch fromresponse
a closedtimeto 10
an ms.
open position, or vice versa. All possible pressure changes in the complete
■ Maximum
circuit mustleakage = RPCC,
be considered RPEC:
to assure 2 in 3/min./1000
a safe, design.3 in3/min./1000 psi, RPIC: 4
psi, RPGC:
functional system
in 3 /min./1000 psi, RPKC: 5 in 3/min./1000 psi.
■ With the -8 control option, the main stage valve should first be installed to the correct torque value. The
■ RPCC
T-8A pilotminimum
controlsetting for allthen
valve should spring ranges isinto
be installed 75 psi
the main stage valve to its required torque value.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
LO ✱RP C – 8✱✱ ✱
✱✱– ✱✱
Nominal
Nominal Capacity Control** Adjustment Range Cracking Pressure
Seal
Capacity Version Control** Seal
A, B, D Versions
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 80 L/min. A Spring biased closed 8 T-8A Cavity in D 3,5 bar at Port 1 N Buna-N
E 25 GPM $ 36.20
Port C Tamper Resistant +$
1 pilot source 4.10for B
hex body 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 160 L/min. pilot operation V Viton
G $ 51.80
50 GPMB Spring K Handknob
biased closed +$
(Pilot5.00
valve toC 150 - 6000 psi +$ 2.00
H 320 L/min. I $ 97.30
100 GPM Port 2 pilot source be ordered N 60 - 800 psi +$ 1.00
separately)
J 640 L/min. K $187.00
D Spring
200 GPM biased closed Q 60 - 400 psi +$ 1.00
higher of Ports 1or 2
pilot source W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com
UK Shortcut Catalogue #999-901-244 89
for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Logic Elements
UNBALANCED POPPET, PILOT-TO-OPEN SWITCHING ELEMENT
Relief Valves
2
PILOT OPERATED, BALANCED PISTON
c
b Full Adjustment 5 Turns 3
+ -
1
3 2 1
Port c Locating
Shoulder
b Cartridge Dimensions
Nominal Typical Installation
Locating Cartridge Cavity a b c Torque
a Shoulder Capacity Model Code Cartridge Dimensions (Nm)
2
Port TypicalLKDC – XDN
60 L/min. T - 11A 34,9 22,2 c 28 Installation
40/50
Capacity Cartridge Cavity a b Torque
LKFC – XDN
120 L/min. Model Code T - 2A 34,9 L 28,6 C 35 K 60/70
(lb. ft.)
a
Port 1 240 L/min.RPCC – LAN
12 GPM T - 162A
LKHC – XDN T 1.22
- 17A 3/4”46 2.1131,8 2.17 46 2.31 25/30
200/215
2
Outlet 480 L/min.RPEC – LAN
25 GPM T - 10A
LKJC – XDN T 1.56
- 19A 7/8”63,5 2.0041,3 2.06 59 2.25 30/35
465/500
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
LKDC LKFC LKHC LKJC
Performance Curves
Full Open Pressure Drop
RPCC 14 RPEC 15 RPGC 15 RPIC 15 RPKC
10
Typical Pressure10 Rise
P = bar
P = bar
P = bar
P = bar
10 10
6
5000 5000 5000 5000 5000
5 5 5
2 4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
■
■ Maximum
Area ratio: operating
A3 to A1 pressure
= 1.8:1 = 5000 psi
■
■ Will accept
Area maximum
ratio: A3 to A2 = pressure
2.25:1 at Port 2.
■
■ Control orifice diameter = port
Back pressure on the tank LKDC:(port 2)mm,
0,8 is directly
LKFC:additive
0,9 mm,atLKHC:
a 1:1 ratio
1,6 to theLKJC:
mm, valve setting.
2,4 mm
■
■ Factory pressure settings established at 4 GPM
Pilot volume for complete shift = LKDC: 0,33 c.c., LKFC: 1,0 c.c., LKHC: 2,5 c.c., LKJC: 4,9 c.c.
■
■ Typicalvalves
These response time 10 ms.
are pressure responsive at all three ports, therefore it is essential to consider all aspects of
■ Maximum
system leakage
operation = RPCC,
through a complete in 3/min./1000
RPEC: 2cycle. Pressure psi, RPGC:
changes at any 3/min./1000 psi, RPIC: 4
3 inone port may cause a valve to
in3/min./1000
switch psi, RPKC:
from a closed in3/min./1000
to an 5open position, orpsi.
vice versa. All possible pressure changes in the complete
■ circuit
RPCC must
minimumbe considered
setting fortoall
assure
springa safe,
ranges functional
is 75 psi system design.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
LK ✱RP
✱ ✱ –C –✱✱✱ ✱
✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Capacity Version Control** Cracking Pressure Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. C Port 3 pilot source X Non-adjustable D 3,5 bar at Port 3 N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 120 L/min. G 50 GPM $ 51.80 K Handknob +$ 5.00
Available in D and F
C 150 - 6000 psi +$ 2.00
V Viton
Capacities Only
H 240 L/min. I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
L Manual Release
J 480 L/min. K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
c Locating
Shoulder
1 3 1 3 Cartridge Dimensions
3 Typical c Installation
Capacity
LP*A CartridgeLP*C Cavity a b Torque
Port Locating Model Code L C K (lb. ft.)
a Shoulder 12 GPM RPCC – LAN T - 162A 1.22 3/4”
Cartridge2.11 2.17
Dimensions 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 Installation
30/35
Nominal Typical c
Outlet Cartridge T - 3A Cavity 1.88 a 1 1/8” b 2.12 Torque
a Capacity RPGC –Model
50 GPM LAN Code X 2.18 L 2.38 45/50
(Nm)
2
Port Inlet 1
10030 L/min. RPIC LPBC
GPM – LAN– XHNT - 16AT - 163A2.44 31 1 1/4” 19,1 2.44 32 2.47 65 2.69 150/160
35/40
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
60 L/min. LPDC – XHN T - 11A 34,9 22,2 31 64 40/50
Performance
Port 1 Curves 120 L/min. LPFC – XHN T - 2A 34,9 28,6 35 72 60/70
RPCC RPEC 240 L/min. RPGC
LPHC – XHN T - 17A RPIC
46 31,8 46 RPKC
84 200/215
480 L/min. LPJCTypical
– XHNPressure
T - Rise
19A 63,5 41,3 59 100 465/500
Performance
5000 Curves 5000 5000 5000 5000
4000 4000 4000 4000
P = psi
4000 P = psi
P = psi
P = psi
P = psi
LPBC
3000 LPDC
3000 LPFC
3000 LPHC
3000
LPJC
3000
2000 2000 2000 2000 2000
1000 1000 Capacity 1000
as a Restrictive Compensator
1000 1000
20 0 5 10 15 20 25 80 0 10 20 30 40 50 160 0 20 40 60 80 100 320 0 40 80 120 160 200 600 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
Q = L/min.
500
Q = L/min.
Q = L/min.
Q = L/min.
Q = L/min.
15 60 120 240
400
10
■ Maximum
40 operating pressure 80= 5000 psi 160 300
200
5 ■ Will 20 accept maximum pressure 40 at Port 2. 80
100
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
LP ✱RP
✱ ✱ –C –✱✱✱ ✱
✱✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Control Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 30 L/min. A Internal pilot Port 1 X Non-adjustable D 3,5 bar N Buna-N
E 25 GPM to$Port
36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi
3 (mainstage +$ 0.00 V Viton +$ 2.00
D 60 L/min. reducing element) F 7,0 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
F 120 L/min. I C External
100 GPM $ 97.30 pilot N 60in
Available D psi
- 800 G*10,0
+$ 1.00bar
(restrictive Adjustment Range only
H 240 L/min. K $187.00
200 GPM compensator) Q 60 - 400 psi +$ 1.00
H 14,0 bar
L Tuning Adjustment
J 480 L/min. W 150 - 4500 psi
+ 25% of customer +$ 0.00
specified flow
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
* G Adjustment Range
** See page 162 for information not available in
on Control Options LPBA, LPBC.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c
b
Logic Elements Locating
Shoulder
NORMALLY CLOSED MODULATING
Typical ELEMENT Cartridge Dimensions
c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 2 2
12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
b 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 c 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
1 3 1 3
Performance
3 Curves
Port Locating LR*A LR*C
RPCC RPEC
Shoulder RPGC RPIC RPKC
Typical Pressure Rise Cartridge Dimensions
Nominal Typical 5000
c 5000
Installation
5000 5000
5000 Cartridge Cavity a b Torque
a 4000 Capacity 4000
Model Code 4000 X L
4000
(Nm)
P = psi
4000
2
P = psi
P = psi
P = psi
P = psi
■ Maximum 240operating
L/min. LRHC –=XHN
pressure 5000 psi T - 17A 46 31,8 46 84 200/215
■ 480 L/min. LRJC – XHN
Will accept maximum pressure at Port 2. T - 19A 63,5 41,3 59 100 465/500
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Typical response time 10 ms.
■
■ Maximum leakage
Maximum operating= pressure = 350 bar
RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Control orifice diameter = LRB*, LRD*, LRF*: 0,4 mm, LRH*, LRJ*: 0,53 mm.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
LR ✱RP
✱ ✱ –C –✱✱✱ ✱
✱✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Control Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 30 L/min. A Internal pilot Port 1 X Non-adjustable D 3,5 bar N Buna-N
E 25 GPM to$Port
36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi
3 (mainstage +$ 0.00 V Viton +$ 2.00
D 60 L/min. G 50 GPM relief element) K Handknob
$ 51.80 +$ 5.00 C 150 - 6000 psi F 7,0
+$ bar
2.00 V Viton
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
* G Adjustment Range
** See page 162 for information not available in
on Control Options LRBA, LRBC.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4 c
Drain
2 1 1
3 c
Pilot Locating
b Shoulder Cartridge Dimensions
Nominal Typical Installation
Locating Cartridge Cavity a b c Torque
Shoulder Capacity Model Code (Nm)
a Cartridge Dimensions
2 60 L/min. DODS – XHN
Typical T - 21A 34,9 22,2 c 46 40/50
Installation
Capacity Cartridge Cavity a b Torque
Port DOFS – XHN
120 L/min. Model Code T - 22A 34,9 L 28,6 C 51 K 60/70
(lb. ft.)
a 12 240
GPM L/min.RPCC –DOHS
LAN – XHN
T - 162A T - 1.22
23A 3/4”
46 2.1131,8 2.17 63 2.31 25/30
200/215
2 Port 1
Outlet
25 480
GPM L/min.RPEC –DOJS
LAN – XHN
T - 10A T - 1.56
24A 7/8”
63,5 2.0041,3 2.06 81 2.25 30/35
465/500
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Performance
Inlet 1Curves
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
DODS DOFS DOHS DOJS
Performance Curves
Fully Open Pressure Differential vs. Flow
RPCC RPEC RPGC RPIC RPKC
20 20 20 20
Typical Pressure
15 Rise 15
P = bar
P = bar
15 15
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
5 5 5 5
3000 3000 3000 3000 3000
2000 2000 2000 2000 2000
0 10 20 30 40 50 60 0 20 40 60 80 100 120 0 40 80 120 160 200 240 0 80 160 240 320 400 480
1000
Flow = L/min.
1000
Flow = L/min.
1000 Flow = L/min.
1000
Flow =1000
L/min.
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Maximum operating pressure = 350 bar (Port 1 and Port 2)
■ Maximum operating pressure = 5000 psi
■
■
Minimum
Will acceptpilot pressure
maximum to shiftatvalve
pressure Port=2.DODS: 30 bar, DOFS, DOHS, DOJS: 20 bar,
■
■ Maximum
Back pressure on the tank port (portPort
valve leakage, Port 1 to 2 directly
2) is or Port 2additive
to Port 1at=a 0,4
1:1 cc/min.
ratio to the valve setting.
■
■ Pilot volume for complete shift = DODS:
Factory pressure settings established at 4 GPM0,16 c.c., DOFS: 0,33 c.c., DOHS: 0,82 c.c.,
DOJS: 2,8 c.c.
■ Typical response time 10 ms.
■
■
Valve will open when the pilot pressure falls below 10 bar.
Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Any
3 back pressure
in /min./1000 at the drain
psi, RPKC: 5 in3port is directly
/min./1000 psi. additive to the required pilot pressure for reliable
■ operation.
RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ S
DO C – ✱ H
✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Control Pressure Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. X Non-adjustable H 14,0 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F
G
120 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
V Viton
I
H GPM $ 97.30
100 L/min.
240 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
P = bar
15 15
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
■ Maximum operating
Minimum pilot pressure
pressure = 5000
to shift valvepsi
with Port 4 vented to tank = DODR: 30 bar,
■ DOFR,
Will DOHR,
accept DOJR:pressure
maximum 20 bar at Port 2.
■
■ Maximum
Back valve
pressure onleakage,
the tank Port
port 1(port
to Port
2) is2 directly
or Port 2additive
to Port at
1 =a 0,4
1:1 cc/min.
ratio to the valve setting.
■ Control pressure
Factory pilot flowsettings
= DODR, DOFR: 0,4
established at 4L/min.,
GPM DOHR, DOJR: 0,6 L/min.
■ Typical response
Valve will time the
open when 10 ms.
pilot pressure falls below 10 bar or with Port 4 blocked.
Maximum 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
■ Port 4 may leakage = RPCC,
be externally RPEC:to2 ainpilot
connected switching valve. The pilot valve should have a leakage rate
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
of less than 10 drops/min. and be able to satisfy the pilot flow requirements. Sun model DAAA-***
■ solenoid
RPCC pilot valve
minimum is ideal
setting for for this application.
all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
DO ✱CR –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control** Control Pressure Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. X Non-adjustable H 14,0 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F
G 120GPM
50 L/min. $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
IH 100 L/min. $ 97.30
240 GPM N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
94 UK Shortcut Catalogue #999-901-244
6 US Shortcut Catalogue #999-901-243
Logic Elements
NORMALLY OPEN, VENT-TO-OPERATE WITH INTEGRAL PILOT CONTROL
CAVITY
Relief Valves 2
The -8 control option allows a pilot control valve to be incorporated
PILOT OPERATED, BALANCED PISTON
directly into the end of the cartridge via the T-8A cavity. These pilot
T-8A control cartridges are sold separately and include solenoid, air pilot,
b Cav 3
Full Adjustment 5 Turns and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
+ -
c 4 1
4
Drain 2 1
3 c
Pilot Locating Cartridge Dimensions
b Shoulder Typical Installation
Nominal Cartridge Cavity a b c Torque
Locating Capacity Model Code (Nm)
a Shoulder
2 60 L/min. DODR – 8HN T - 21A Cartridge Dimensions
34,9 22,2 46 40/50
Port Typical
DOFR – 8HNCavity
120 L/min. Cartridge T - 22A
c Installation
Capacity a b34,9 28,6 51 60/70
Torque
Model Code – 8HN L C K (lb. ft.)
a 240 L/min. DOHR T - 23A 46 31,8 63 200/215
1 Port 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
480 L/min. DOJR – 8HN T - 24A 63,5 41,3 81 465/500
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
DODR-8 DOFR-8 DOHR-8 DOJR-8
RPCC RPEC Fully Open Pressure Differential vs. RPIC
RPGC Flow RPKC
20 20 20 20
Typical Pressure
15
Rise 15
P = bar
P = bar
15 15
P = bar
P = bar
4000
P = psi
P = psi
P = psi
P = psi
5 5 5 3000 5 3000
3000 3000 3000
2000 2000 2000 2000 2000
0 10 20 30 40 50 60 0 20 40 60 80 100 120 0 40 80 120 160 200 240 0 80 160 240 320 400 480
1000 1000 1000
Flow = L/min.
1000
Flow = L/min.
1000
Flow = L/min. Flow = L/min.
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■ Maximum operating pressure = 350 bar
■ Maximum operating pressure = 5000 psi
■ Minimum pilot pressure to shift valve = DODR: 30 bar, DOFR, DOHR, DOJR: 20 bar,
■ Will accept maximum pressure at Port 2.
■ Maximum valve leakage, Port 1 to Port 2 or Port 2 to Port 1 = 0,4 cc/min.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■
Control
Factory pilot flowsettings
pressure = DODR, DOFR: 0,4
established at 4L/min.,
GPM DOHR, DOJR: 0,6 L/min.
■
■ Valve will open when the
Typical response time 10 ms. pilot pressure falls below 10 bar.
■
■ Any back pressure at the drain port is
Maximum leakage = RPCC, RPEC: 2 in /min./1000directly
3 additivepsi,
to RPGC:
the required pilot pressure.
3 in3/min./1000 psi, RPIC: 4
■ in3/min./1000
With psi, RPKC:
the -8 control in3main
option, 5the /min./1000 psi. should first be installed to the correct torque value. The
stage valve
■ T-8A
RPCCpilot controlsetting
minimum valve should then beranges
for all spring installed into
is 75 psithe main stage valve to its required torque value.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ R
DO C – ✱
8 ✱✱
Nominal
Nominal
Capacity Control**
Control**
Adjustment Range
Control Pressure
Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. 8 with T-8A cavity H 14,0 bar N Buna-N
E 25 GPM $ 36.20 C in
Tamper Resistant
hex body for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
FG 120 L/min. $ 51.80
50 GPM K pilot operation
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
(see pilot control
I
H GPM $ 97.30
100 L/min.
240 section for alternate N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 options) Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
3
2 1
b c
b c 4 1
4 Locating
Shoulder
Drain CartridgeCartridge Dimensions
Dimensions
Typical
Typical cc Installation
Installation
3 Locating Capacity
Nominal Cartridge
Cartridge Cavity a a bb Torque
Torque
Pilot Shoulder
Capacity
ModelModel
Code Code Cavity LL CC K K (Nm)
(lb. ft.)
a 1260GPM
L/min. DODP
RPCC – LAN T - 162A
– LAN T - 21A 1.22
34,9 22,2
3/4” 79
2.11 80,0
2.17 85,02.31 40/50
25/30
2 a 25 GPM
120 DOFP
L/min. RPEC – LAN T - 10A
– LAN T - 22A 1.56
34,9 7/8”
28,6 2.00
88 2.06
89,0 94,02.25 30/35
60/70
2
Outlet
Port 50
240 L/min. RPGC
GPM – LAN
DOHP – LAN T - 3A
T - 23A 1.88
46 1 1/8”
31,8 2.12
100 2.18
101,0 2.38
106,0 45/50
200/215
100 L/min. RPICDOJP
480GPM – LAN
– LAN T - 16A
T - 24A 2.44
63,5 1 1/4”
41,3 2.44
122 2.47
125,0 2.69
128,0 150/160
465/500
Inlet 11
Port
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC DODP RPEC DOFP RPGC DOHP RPIC DOJP RPKC
Typical Pressure Rise
Fully Open Pressure Differential vs. Flow
5000 5000 5000 5000 5000
20 20 20 20
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
15 15
P = bar
P = bar
15 15 3000
P = bar
3000
P = bar
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ P
DO C – ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment
Nominal Range
Adjustable Seal
Capacity Control** Shift Pressure Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. L Standard Screw A 21 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G
F L/min. $ 51.80
50 GPM
120 K Tamper
C Resistant +$ 5.00
Handknob C 21
B 150- 105
- 6000
barpsi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
H 240 L/min. K Handknob W 21 - 315 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4 3
2 1
4 c
Drain c
1
3b
Pilot Locating
Locating
Shoulder Cartridge Dimensions
Shoulder
Typical Cartridge Dimensions Installation
Nominal
Capacity Typical Cartridge Cavity a b c c Torque
Installation
a Capacity Model Code Cavity
Cartridge a b (Nm)Torque
2 L C K
a 60 L/min. Model Code
DKDS – XHN T - 21A 34,9 22,2 46 (lb. ft.)
40/50
Port 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 120 L/min. DKFS – XHN T - 22A 34,9 28,6 51 60/70
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 240 L/min. DKHS – XHN T - 23A 46 31,8 63 200/215
Port 1 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
480 L/min. DKJS – XHN T - 24A 63,5 41,3 81 465/500
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
DKDS
RPCC DKFS
RPEC DKHS
RPGC RPIC DKJS RPKC
Pilot OpenPressure
Typical PressureRise
Drop
25 25 25 25
5000 5000 5000 5000 Flow from
5000 Flow from
20 20 20 20 Port 2 to Port 1
Port 2 to Port 1
4000
P = bar
P = bar
4000 4000 4000
P = bar
P = psi
4000
P = bar
P = psi
P = psi
P = psi
P = psi
15 15 15 15 Flow from
3000 3000 3000 3000
Flow from 3000
Port 1 to Port 2
10 10 Port 1 to Port 2 10
2000 10 2000 2000 2000 2000
1000 5 1000 5 1000 5 1000 5 1000
0 0 5 10 1020 15
30 20
40 25
50 60 0 010 20 20 40 30 60 4080 50
100 120 0 020 4040 80 60 120 80
160100200 240 0 40 80 120 0 160
80 200
160 240 0 400
320 80 480160 240 320 400
Flow = GPM
Flow = L/min. FlowFlow
= GPM
= L/min. FlowFlow
= GPM
= L/min. Flow = GPM Flow = L/min. Flow = GPM
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ S
DK C –
– ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. X Non-adjustable H 14,0 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F
G 120 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
I
H GPM $ 97.30
100 L/min.
240 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
3
2 1
b c
c 4 1
b
4 Locating
Drain Shoulder
CartridgeCartridge Dimensions
Dimensions
3 Nominal Typical
Typical cc Installation
Installation
Locating Capacity Cartridge
Cartridge Cavity
Cavity a a bb Torque
Torque
Pilot Shoulder Capacity
ModelModel
Code Code LL CC K K (Nm)
(lb. ft.)
a 1260GPM
L/min. DKDP
RPCC – LAN T - 162A
– LAN T - 21A 1.22
34,9 22,2
3/4” 79
2.11 80,0
2.17 85,02.31 40/50
25/30
2 a 25
120 L/min. RPEC
GPM – LAN
DKFP – LAN T - 10A
T - 22A 1.56
34,9 7/8”
28,6 2.00
88 2.06
89,0 94,02.25 30/35
60/70
2
Outlet
Port 50
240 L/min. RPGC
GPM – LAN
DKHP – LAN T - 3A
T - 23A 1.88
46 1 1/8”
31,8 2.12
100 2.18
101,0 2.38
106,0 45/50
200/215
100 L/min. RPICDKJP
480GPM – LAN
– LAN T - 16A
T - 24A 2.44
63,5 1 1/4”
41,3 2.44
122 2.47
125,0 2.69
128,0 150/160
465/500
Inlet 11
Port
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC DKDP RPEC DKFP RPGC DKHP RPIC DKJP RPKC
Typical Pressure Rise
Piloted Open Pressure Drop
5000 5000 5000 5000 5000
25 25 25 25
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
20 20 20 20
P = bar
P = bar
P = bar
3000
P = bar
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
DK ✱PC –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment
Nominal Range
Adjustable Seal
Capacity Control** Shift Pressure Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D
E 60
25 L/min.
GPM $ 36.20 L
C Standard Screw +$ 4.10
Tamper Resistant A
B 21
50 -- 210
1500bar
psi +$ 0.00 N
V Buna-N
Viton +$ 2.00
G
F L/min. $ 51.80
50 GPM
120 K Tamper
C Resistant +$ 5.00
Handknob C 21
B 150- 105
- 6000
barpsi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
H 240 L/min. K Handknob W 21 - 315 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b
Relief Valves
4 3
PILOT OPERATED, BALANCED PISTON
4 c
Full Adjustment 5 Turns
Drain 1
+ -
3
Locating
Pilot Shoulder
2 1
ac
2b Cartridge Dimensions
Port Nominal Typical Installation
Capacity Cartridge Cavity a b c Torque
Locating Model Code (Nm)
Port 1 Shoulder
60 L/min. DKDR – XHN T - 21A Cartridge
34,9 Dimensions
22,2 46 40/50
Typical c Installation
Capacity DKFR – XHNCavity
120 L/min. Cartridge T - 22A
a b34,9 28,6 51 60/70
Torque
Model Code L C K (lb. ft.)
a 240 L/min. DKHR – XHN T - 23A 46 31,8 63 200/215
12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 480 L/min. DKJR – XHN T - 24A 63,5 41,3 81 465/500
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance Curves 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
DKDR 200 GPM
DKFRRPKC – LAN DKHR
T - 18A 3.13 1 5/8”
DKJR
2.81 2.94 3.06 350/375
P = bar
P = bar
P = bar
15 15 Typical Pressure
15 Rise 15
10 10 10 5000 10 5000
5000 5000 5000
5 4000 5 4000 5 4000 5 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
■
■ Maximum operating pressure = 5000 psi
Minimum pilot pressure to shift valve with Port 4 vented to tank = DKDR: 30 bar,
■ DKFR, DKHR,
Will accept DKJR:pressure
maximum 20 bar. at Port 2.
■
■ Maximum
Back pressurevalveonleakage,
the tankPort
port 1(port
to Port
2) is2 directly
or Port 2additive
to Port 1at=a 0,4
1:1 cc/min.
ratio to the valve setting.
■
■ Control pilot flow = DKDR, DKFR: 0,4 L/min., DKHR, DKJR: 0,6 L/min.
Factory pressure settings established at 4 GPM
■
■ Typical
Valve response
will time 10
reseat when thems.
pilot pressure falls below 10 bar.
Maximum 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
■ Port 4 may leakage = RPCC,
be externally RPEC:to
connected 2 ainpilot switching valve. The pilot valve should have a leakage
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
rate of less than 10 drops/min. and be able to satisfy the pilot flow requirements. Sun model DAAA-***
■ solenoid pilot valve
RPCC minimum is ideal
setting for for this application.
all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
DK ✱RC –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Nominal Shift Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. X Non-adjustable H 14,0 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F
G 120 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
I
H GPM $ 97.30
100 L/min.
240 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
2
The -8 control option allows a pilot control valve to be incorporated directly
Relief Valves into the end of the cartridge via the T-8A cavity. These pilot control
cartridges are sold separately and include electro-proportional, solenoid, air
T-8A
3
PILOT
b OPERATED, Cav
BALANCED PISTON
pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
3
Pilot Locating 2 1 Cartridge Dimensions
Shoulder
c Nominal Typical Installation
Capacity Cartridge Cavity a b c Torque
b Model Code (Nm)
2 a 60 L/min. DKDR – 8H* T - 21A 34,9 22,2 46 40/50
Valve Locating
Shoulder 120 L/min. DKFR – 8H* T - 22A 34,9 28,6 51 60/70
Cartridge Dimensions
240 L/min. DKHR – 8H* T - 23A 46 31,8 63 200/215
1 Valve Typical c Installation
Capacity
480 L/min. DKJR – 8H*Cavity
Cartridge a
T - 24A b63,5
L 41,3 C 81 K
Torque
465/500
Model Code (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Performance Curves 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
RPIC – LAN
InletDKDR-8 DKFR-8 DKHR-8 2.44 DKJR-8
100 GPM T - 16A 1 1/4” 2.44 2.47 2.69 150/160
1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Piloted Open Pressure Drop
Performance Curves
25 25 25 25
P = bar
P = bar
P = bar
15 15 15 15
10 10 Typical Pressure
10 Rise 10
5 5 5 5
5000 5000 5000 5000 5000
4000 50 4000 0 40 80 120 4000
160 200 240 0 80 160 2404000
320 400 480
P = psi
P = psi
P = psi
P = psi
■ DKFR,
Maximum DKHR, DKJR:
operating 20 bar = 5000 psi
pressure
■
■ Maximum valve leakage,
Will accept maximum pressure Port 1attoPort
Port2.2 or Port 2 to Port 1 = 0,4 cc/min.
■
■ Control pilot flow
Back pressure = DKDR,
on the tank port DKFR:
(port 2) 0,4isL/min,
directlyDKHR,
additiveDKJR: 0,6ratio
at a 1:1 L/min.
to the valve setting.
■
■ Valve
Factorywill open when
pressure the established
settings pilot pressure at 4falls
GPM below 10 bar.
■
■ Any back
Typical pressuretime
response at the10 drain
ms. port is directly additive to the required pilot pressure for reliable
■ operation.
Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ in3/min./1000
With psi, RPKC:
the -8 control option,5the in3main
/min./1000 psi. should first be installed to the correct torque value. The
stage valve
■ T-8A pilot control valve should
RPCC minimum setting for all spring then beranges
installed into
is 75 psithe main stage valve to its required torque value.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ R
DK C – ✱
8 ✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Nominal Shift Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. 8 with T-8A cavity H 14,0 bar N Buna-N
E 25 GPM $ 36.20 C in
Tamper Resistant
hex body for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F
G 120 L/min. $ 51.80
50 GPM pilot operation
K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
(see pilot control
I
H GPM $ 97.30
100 L/min.
240 section for alternate N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 options) Q 60 - 400 psi +$ 1.00
J 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Directional Cartridge Valves
2 4
2 3
4 2
(A) 2 4 (B)
(A) 2 4 (B)
(X) 6 5 (Y)
2-position, 4-way Detented 111
(P) 3 1 (T)
Performance Curves Typical Pilot Oil Flow vs. Load Typical Pilot Oil Flow vs. Load
Pressure Drop Pressure above Valve Setting Pressure Drop Pressure above Valve Setting
RPCC 30
24
RPEC 1.0
0.8
RPGC 30
24
RPIC 1.0
RPKC
Q = L/min.
0.8
Q = L/min.
P = bar
P = bar
18 0.6
Typical Pressure Rise 18 0.6
12 0.4 12 0.4
4000
P = psi
P = psi
P = psi
P = psi
0 10 20 30 40 0 50 100 150 200 250 300 350 0 20 40 60 80 0 50 100 150 200 250 300 350
3000 Q = L/min.
3000 P = bar3000 Q = L/min.3000 P = bar 3000
2000 2000 2000 2000 2000
1000 1000 1000 1000 1000
0 5 10 15 20
■
25
Maximum
0 10
operating
20 30 40
pressure
50
=0 35020
bar40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM
Flow = GPM ■ MaximumFlow = GPM
valve leakage = 16,4 cc/min. at 70 bar
■
■ Maximum
Control pilotoperating pressure == DPBA,
flow at opening 5000 psiDPBB, DPBC, DPBD = 0,11 - 0,16 L/min., DPCA, DPCB,
■ DPCC,
Will DPCD
accept = 0,16 -pressure
maximum 0,25 L/min.at Port 2.
■ Maximum
Back pressure
pressure on theattank
portport
3 should
(port be limited
2) is to 210
directly bar. at a 1:1 ratio to the valve setting.
additive
■ Factory
Pressurepressure
at port 3settings established
is directly additive at to 4the
GPMsetting of the valve. Because of this, port 3 may not be
■ useable response
Typical as a worktimeport 10
in your
ms. circuit. If this is a consideration, the 4 port version of this valve may
■ be a solution.
Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ For
in DP*C andpsi,
3/min./1000 DP*D RPKC:port 53 in
can be blockedpsi.
3/min./1000 to prevent the cartridge from shifting.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DP ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 30 L/min. A 2 Position 2-Way L Standard Screw A 7 - 210 bar N Buna-N
E 25 GPM $ 36.20OpenC Tamper Resistant
Normally +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 60 L/min. C Tamper Resistant B 3,5 - 105 bar V Viton
G 50 GPMB 2 $ 51.802-Way
Position K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
I 100 GPM Normally
$ 97.30Closed K Handknob N 60 - 800 psi D 2 1.00
+$ - 55 bar
K C 2 $187.00
200 GPM Position 3-Way Q 60 - 400 psi E 2 1.00
+$ - 25 bar
Port 1 Blocked
W 150 - 4500 psi W 100.00
+$ - 315 bar
D 2 Position 3-Way
Port 1 Open
Adjustment Range Options:
A, B, C, and W are standard set atRange
Adjustment 1000 psi.
Options:
N Option is standard set at
A, 400 psi.W are standard set at 70 bar.
B, and
Q Option is standard set at
D 200 psi.is standard set at 25 bar.
Option
** See page 162*for
** See page 162 for information information
Minimum setting 75 psiEonOption is standard set at 14 bar.
all ranges.
on Control Options on Control Options
Customer may specify Customer
pressuremay +$ 1.10
specify pressure
setting. setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
102 UK Shortcut Catalogue #999-901-244
Directional Valves
2 POSITION, 2-WAY AND 3-WAY, WITH EXTERNAL DRAIN
Relief Valves
Full Adjustment 5 Turns 2 4 2 4 2 4 2 4
PILOT + OPERATED,
- BALANCED PISTON
Full Adjustment 5 Turns
+ -
b 1 3 1 3 1 3 1 3
2 1
c DP*M DP*N DP*O DP*P
c
b Cartridge Dimensions
4
Typical c Installation
Port Locating Capacity Cartridge Cavity a b Torque
Shoulder Model Code L C K (Nm)
3 Locating Cartridge Dimensions
Port Shoulder 30 L/min. DPBM
Typical– LAN T - 21A 34,9 22,2 79 81 c 85 40/50
Installation
Capacity
60 L/min. Cartridge
DPCM – LAN Cavity
T - 22A a34,9 b
28,6 88L 90C 94 K Torque
60/70
a Model Code (lb. ft.)
2 a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Port
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Port 1 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
DPB* DPC*
Performance Curves Typical Pilot Oil Flow vs. Load Typical Pilot Oil Flow vs. Load
RPCC RPEC
Pressure Drop RPGC
Pressure above Valve
1.0
Setting PressureRPIC
Drop RPKC
Pressure above Valve
1.0
Setting
30 30
24 0.8
Typical Pressure
24
Rise
Q = L/min.
0.8
Q = L/min.
P = bar
P = bar
18 0.6 18 0.6
5000 12 5000 0.4 5000 12 5000 0.4 5000
6 4000 4000 6 4000 4000
P = psi
P = psi
P = psi
P = psi
0 5 10 15 20 0 10 20 30 40 50 00 80
20 16040240 320 60 80 100 0 40 80 120 160 200 400
■ 25 MaximumFlow operating
Flow = GPM = GPM pressure = 350 Flowbar = GPM Flow = GPM Flow = GPM
■
■ Maximum operating
Maximum valve leakage = 16,4
pressure cc/min.
= 5000 psiat 70 bar
■
■ Control
Will pilotmaximum
accept flow at opening
pressure= at
DPBM,
Port 2.DPBN, DPBO, DPBP = 0,11 - 0,16 L/min., DPCM, DPCN,
■
DPCO,
Back DPCP on
pressure = 0,16 - 0,25
the tank L/min.
port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Maximum
Factory pressure
pressure at portestablished
settings 3 should be
at limited
4 GPM to 210 bar.
■
■ Pressureresponse
Typical at port 4time
is directly
10 ms.additive to the setting of the valve.
■
■ Port 3 can be used as
Maximum leakage = RPCC, a work RPEC:
port. 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Port 4 can be blocked to prevent the cartridge from shifting.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DP ✱RP C –✱✱✱ ✱
✱✱– ✱✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 30 L/min. M 2 Position 2-Way L Standard Screw A 7 - 210 bar N Buna-N
E 25 GPM $ 36.20OpenC Tamper Resistant
Normally +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C 60 L/min. C Tamper Resistant B 3,5 - 105 bar V Viton
G 50 GPM
N 2 $Position
51.80 K Handknob
2-Way +$ 5.00 C 150 - 6000 psi +$ 2.00
I $ 97.30Closed
100 GPM Normally K Handknob N 60 - 800 psi D 21.00
+$ - 55 bar
K O 2 $187.00
200 GPM Position 3-Way Q 60 - 400 psi +$
E 21.00
- 25 bar
Port 1 Blocked
W 150 - 4500 psi +$
W 100.00
- 315 bar
P 2 Position 3-Way
Port 1 Open
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Adjustment Range Options:
Q Option is standard set at
A, 200 psi.W are standard set at 70 bar.
B, and
** See page 162 for information * Minimum setting 75 psiDonOption
all ranges.
is standard set at 25 bar.
on Control Options** See page 162Customer may specify pressure
for information is standard set+$
E Optionsetting. 1.10
at 14 bar.
on Control Options Customer may specify pressure setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
2 1
c 1 3 1 3 1 3 1 3
b c
b DRBA DRBB DRBC DRBD
Locating
Shoulder Cartridge Dimensions
Cartridge Dimensions
Typical c Installation
Typical c Installation
3 Capacity Cartridge Cavity aa bb Torque
Locating Capacity Cartridge
Model Code Cavity LL CC K K Torque
(Nm)
Port Shoulder Model Code (lb. ft.)
a 30 GPM
12 L/min. DRBA
RPCC – LAN
– LAN T -T162A
- 11A 34,9
1.22 22,2
3/4” 79
2.11 812.17 852.31 40/50
25/30
2 a 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
2
Outlet
Port 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 1
Port
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance
Performance Curves
Curves
RPCC
DRBA RPEC DRBB RPGC DRBC RPIC DRBDRPKC
Typical Pressure
Typical Pressure Drop
Rise
5000 25 Port5000
2 5000 5000 5000 Port 1 to Port 2
25 25 Port 2
to Port Port 2 25
40003 4000 4000 to Port 3 4000
P = psi
4000 20 20 to Port 3 20
P = psi
P = psi
P = psi
P = psi
20 Port 2
P = bar
P = bar
P = bar
P = bar
15 15
2000 15 2000
2000 10 2000 10 2000 10
1000 Port 1 10 1000
1000 1000 1000
5 5 5 to Port 2
5
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
0 Flow20
10 = GPM
30 40 50 Flow
0 = 10
GPM 20 30 40 50 Flow = GPM
0 10 20 30 40 Flow
50 = GPM Flow = GPM
Q = L/min. Q = L/min. Q = L/min. 0 10 20 30 40 50
Q = L/min.
■ Maximum operating pressure = 5000 psi
■
■ Will acceptoperating
Maximum maximum pressure= at
pressure Port
350 bar2.
■
■ Back pressure on the tank port
Maximum valve leakage = 32,8 cc/min. (port 2) isatdirectly
70 bar additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure settings established at 4 GPM
Maximum pressure at port 3 should be limited to 210 bar.
■
■ Typical response
Pressure at port 3 time 10 ms.additive to the setting of the valve. Because of this, port 3 may not be
is directly
■ Maximum
useable as a work port in yourRPEC:
leakage = RPCC, in 3this
circuit.2 If /min./1000 psi, RPGC:the
is a consideration, 4 3port
3 in /min./1000
versionpsi, RPIC:
of this 4 may
valve
3
in a/min./1000 3
be solution. psi, RPKC: 5 in /min./1000 psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DR ✱RP
✱ ✱ –C –✱✱✱ ✱
✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 30 L/min. A 2 Position 2-Way L Standard Screw A 35 - 210 bar N Buna-N
E $ 36.20OpenC Tamper Resistant +$ 4.10 B 50 - 1500 psi
25 GPM Normally +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob C Tamper Resistant
+$ 5.00 C 150 - 6000 psi B
+$ 142.00
- 105 bar V Viton
B 2 Position 2-Way
I $ 97.30Closed
100 GPM Normally K Handknob N 60 - 800 psi D
+$ 1,5
1.00
- 55 bar
K $187.003-Way
C 2 Position
200 GPM Q 60 - 400 psi +$ 1,5
E 1.00
- 25 bar
Port 1 Blocked
W 150 - 4500 psi +$ 1,5
S 0.00
- 14 bar
D 2 Position 3-Way
Port 1 Open W 50 - 315 bar
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Adjustment Range Options:
A, B, and W are standard set at 70 bar.
D Option is standard set at 25 bar.
** See page 162 for information E and S are standard set at 14 bar.
on Control
Visit www.sunhydraulics.com for detailed and completeOptions Customer
technical information mayline
on our full specify pressure setting.
of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c 1
b
b
c Locating 1 3 1 3 1 3 1 3
Shoulder 4
DRBM DRBN DRBO Cartridge
DRBP Dimensions DRBR
External Drain Typical
External Drain External Drain External Drain External
c Pilot Installation
4 Capacity Cartridge Cavity a b Torque
Port Model Code L C
Cartridge Dimensions K (lb. ft.)
a 12 GPM RPCC Typical
– LAN T - 162A 1.22 3/4” 2.11 c2.17 2.31 Installation
25/30
3 Capacity Cartridge Cavity a b Torque
2
Port Locating 25 GPM RPEC – LAN T - 10A 1.56 7/8” L
2.00 C2.06 K2.25 30/35
Shoulder Model Code (Nm)
Outlet
50
30GPM
L/min. RPGC – LAN
DRBM – LAN T - T3A- 21A 1.88
34,9 122,2
1/8” 2.12
79 2.18
81 852.38 45/50
40/50
a 100
30 GPM
L/min. RPIC – LAN
DRBN – LAN T - T16A
- 21A 2.44
34,9 122,2
1/4” 2.44
79 2.47
81 852.69 150/160
40/50
2 Inlet 1
Port 200
30 GPM
L/min. RPKC – LAN
DRBO – LAN T - T18A
- 21A 3.13
34,9 122,2
5/8” 2.81
79 2.94
81 853.06 350/375
40/50
Performance Curves 30 L/min. DRBP – LAN T - 21A 34,9 22,2 79 81 85 40/50
1 Port
RPCC RPEC 30 L/min. DRBR – LAN
RPGC T - 21A 34,9RPIC22,2 79 81 RPKC85 40/50
Performance Curves
Typical Pressure Rise
DRBM
5000
DRBN
5000
DRBO
5000
DRBP
5000
DRBR
5000
4000 4000 4000 4000
Typical Pressure Drop
P = psi
4000
P = psi
P = psi
P = bar P = psi
P = bar P = psi
P = bar
P = bar
15 15 Port 3 15 15 Port 3 15 Port 3
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
10
Flow = GPM Port 1
10
Flow = GPM
10
Flow = GPM Port 1
10 Flow = GPM 10
Flow = GPM
5 to 5 5 to 5 5
Port 2 Port 2
0 10 20 30 40
■
50
Maximum
0 10
operating
20 30 40
pressure
50
= 5000
0 10 20
psi30 40 50 0 10 20 30 40 50 0 10 20 30 40 50
Q = L/min. Q =maximum
L/min. Q = L/min. Q = L/min. Q = L/min.
■ Will accept pressure at Port 2.
■
■ Back
Maximumpressure on the pressure
operating tank port=(port
350 2)
baris directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure settings established at 4 GPM
■ Maximum valve leakage = 32,8 cc/min. at 70 bar
■ Typical response time 10 ms.
■ Maximum pressure at port 3 should be limited to 210 bar.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ DRBM,
in DRBN,
3/min./1000 psi,DRBO,
RPKC:DRBP: Port 3 canpsi.
5 in3/min./1000 be used as a work port
■
■ RPCC minimum setting for all spring rangesport
DRBM, DRBN, DRBO, DRBP: Pressure at is 754 psi
is directly additive to the setting of the valve.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
DR ✱ C – ✱✱✱ ✱ ✱
✱✱–
Nominal Nominal
Capacity Version Control** Adjustment Range Adjustment Range
Control** Seal Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 30 L/min. M 2-Position, 2-Way, L Standard Screw A 35 - 210 bar N Buna-N
E 25 GPM $ 36.20Open,
Normally C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
External Drain C Tamper Resistant B 14 - 105 bar V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
I N 2-Position,
100 GPM $ 97.30 2-Way, K Handknob N 60 - 800 psi N* 41.00
+$ - 55 bar
Normally Closed,
K $187.00
200 GPM External Drain Q 60 - 400 psi E* 21.00
+$ - 25 bar
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
18
12
Typical Pressure Rise
6
5000 5000 5000 5000 5000
4000 0
4000 10 20 30 40 4000 4000
P = psi
4000
P = psi
Q = L/min. P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DV ✱RP
✱ ✱ –C – 8✱✱ ✱ ✱
Nominal Nominal
Capacity Version Control** Adjustment Range Adjustment Range
Control** Seal Seal
Capacity
B 28 L/min. C A 2$
12 GPM* 31.90 2-Way
Position, L Standard Screw 8 +$
T-8A0.00 A 100 - 3000 psi
Cavity in +$
F 70.00
bar N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20
Normally OpenC Tamper Resistant +$
in hex4.10 B 50 - 1500 psi
body for +$ 0.00 V Viton +$ 2.00
pilot operation V Viton
G 50 GPMB 2 $ 51.80 2-Way
Position, K Handknob +$
(Pilot5.00
valve toC 150 - 6000 psi +$ 2.00
Normally Closed be ordered
I 100 GPM $ 97.30 separately) N 60 - 800 psi +$ 1.00
K C 2 $187.00
200 GPM Position, 3-Way, Q 60 - 400 psi +$ 1.00
Port 1 Blocked
W 150 - 4500 psi +$ 0.00
D 2 Position, 3-Way,
Port 1 Open
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 *for
** See page 162 for information information
Minimum setting 75 psi on all ranges.
on Control Options on Control Options
Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6
106 US
UK Shortcut
Shortcut Catalogue
Catalogue #999-901-243
#999-901-244
Directional Valves
4-PORT, 2-WAY AND 3-WAY WITH INTEGRAL PILOT CONTROL CAVITY
Relief Valves
PILOT OPERATED, 4BALANCED
2 2 PISTON
4 2 4 2 4
The -8 control option allows the pilot
control valve to be incorporated directly
b Full Adjustment 5 Turns into the end of the cartridge via
T-8A T-8A T-8A T-8A
the T-8A cavity. These pilot control
+ - cartridges are sold separately and
include solenoid, air pilot, and hydraulic
c 1 3
pilot operation. See Pilot Control Cartridges
4
2 11 3 1 3 1 3
on page 121.
Port
c
DVBM-8 DVBN-8 DVBO-8 DVBP-8
3
b
Port Locating Cartridge Dimensions
Shoulder
Locating Typical Installation
Shoulder Capacity Cartridge Cavity aCartridge bDimensionsc Torque
Model Code (Nm)
Typical c Installation
a 28 L/min.
Capacity DVBM – 8FN Cavity T-21A a
Cartridge 35,1
b 22,2 42,9 45/50Torque
2 Model Code L C K (lb. ft.)
Port a 28 L/min. DVBN – 8FN T-21A 35,1 22,2 42,9 45/50
12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 28 L/min. DVBO – 8FNT - 10A T-21A 35,1 22,2 42,9 45/50
25 GPM RPEC – LAN 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet1 Port
50 28 RPGC DVBP
– LAN– 8FNT - 3A
GPML/min. T-21A1.88 135,1
1/8” 22,2
2.12 42,9
2.18 2.38 45/5045/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
Performance Curves 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
4000
P = psi
P = psi
12
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DV ✱RP
✱ ✱ –C – 8✱✱ ✱
✱✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Version Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 28 L/min. M 2 Position, 2-Way 8 T-8A Cavity in F 7 bar N Buna-N
E 25 GPM $ 36.20OpenC Tamper Resistant +$
Normally 4.10for B
hex body 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
pilot operation V Viton
G 50 GPMN 2 $ 51.80 K
Position, 2-Way Handknob +$
(Pilot5.00
valve toC 150 - 6000 psi +$ 2.00
I Normally
100 GPM $ 97.30 Closed be ordered N 60 - 800 psi +$ 1.00
separately)
K O 2 $187.00
200 GPM Position, 3-Way, Q 60 - 400 psi +$ 1.00
Port 1 Blocked
W 150 - 4500 psi +$ 0.00
P 2 Position, 3-Way,
Port 1 Open
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
0 20
■
40 Will
60 accept
80 100 maximum0 40 pressure
80 120 at Port
160 200 2. 0 40 80 120 160 200 240 0 40 80 120 160 200 240
Q = L/min. Q = L/min. Q = L/min.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the Q = L/min.
valve setting.
■
■ Factory pressure settings established
Maximum operating pressure = 350 bar at 4 GPM
■
■ Typical
The main response timeshould
stage valve 10 ms.first be installed to the correct torque value followed by the T-8A pilot
■ Maximum leakage
control section into=theRPCC,
main RPEC: 2 in 3to
stage valve /min./1000 psi,torque
its required RPGC: 3 in3/min./1000 psi, RPIC: 4
value.
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Main stage leakage less than 0,3 cc/min.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DFRP
✱✱A C– –8 ✱D ✱✱ ✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment RangeRange Seal Seal
Capacity
C C 12 GPM*
60 L/min. $ 31.908 L Standard
T-8A hex body+$ 0.00
cavity inScrew D - 3000
A 100 3,5 bar
psi +$ 0.00 N Buna-N
N Buna-N +$ 0.00
for pilot operation (Pilot
D 120 E 25 GPM
L/min. $ 36.20 C Tamper
valve Resistant
to be ordered +$ 4.10
separately) B 50 - 1500 psi +$ 0.00 V VitonV +$ 2.00
Viton
G 50 GPM $ 51.80 Options
K Handknobare: +$ 5.00 C 150 - 6000 psi +$ 2.00
E 240 L/min. • Solenoid Pilot
I 100 GPM $ 97.30 • Air Pilot N 60 - 800 psi +$ 1.00
F 480 L/min. • Hydraulic Pilot
K 200 GPM $187.00 • Manual Control Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b Locating
Shoulder
Locating 1
Shoulder
Cartridge Dimensions
Typical c Installation
Capacity Cartridge Cavity a b Torque
a Model Code L C
Cartridge Dimensions K (lb. ft.)
2 a 12 GPM Typical T - 162A
RPCC – LAN 1.22 3/4” 2.11 2.17 2.31 Installation
25/30
Port2 Capacity Cartridge Cavity a b c Torque
25 GPM RPEC – LAN T - 10A
Model Code 1.56 7/8” 2.00 2.06 2.25 (Nm)30/35
Outlet
50 60
GPML/min. RPGC DFCB
– LAN– 8DNT - 3A T - 13A
1.88 34,9
1 1/8” 22,2
2.12 18
2.18 2.38 40/5045/50
100120
GPML/min. RPIC DFDB
– LAN– 8DNT - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 11
Port T - 5A 41,1 28,6 18 60/70
200240
GPML/min. RPKC DFEB
– LAN– 8DNT - 18A 3.13
T - 16A 1 5/8”
61,9 2.81
31,8 2.94
25 3.06 200/215
350/375
Performance Curves
RPCC
Performance Curves RPEC RPGC RPIC RPKC
Typical Pressure Rise
5000
DFCB-8
5000 DFDB-8
5000 DFEB-8
5000 5000
4000 4000 4000 4000
P = psi
4000
Typical Pressure Drop
P = psi
P = psi
P = psi
P = bar P = psi
P = bar
10 10
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 3,50 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM 7 Flow = GPM 7 Flow = GPM Flow = GPM Flow = GPM
3,5 3,5 2
■ Maximum operating pressure = 5000 psi
0 20 40 60 80 100 0 40 80 120 160 200 0 40 80 120 160 200 240
■ Will accept Q =maximum
L/min. pressure at PortQ =2.L/min. Q = L/min.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Main
Factorystage leakage
pressure less than
settings 5 drops/min.Maximum
established at 4 GPM operating pressure = 350 bar
■
■ The main stage valve
Typical response time 10 ms.should first be installed to the correct torque value followed by the T-8A pilot
■ control section into the main stage valve 3to
Maximum leakage = RPCC, RPEC: 2 in /min./1000 psi, RPGC:its required torque value.
3 in3/min./1000 psi, RPIC: 4
■ in3/min./1000
Main psi, RPKC:
stage leakage less than 3/min./1000
5 in0,3 cc/min. psi.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱B
DF ✱ C –
– ✱ ✱✱
8 D ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control Adjustment Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. T-8A Pilot Cavity D Bias Spring N Buna-N
E 25 GPM $ 36.20 C Tamper
Pilot Resistant +$ 4.10
Stage Control B 3,5
50 -bar
1500 psi +$ 0.00 V Viton +$ 2.00
D
G 120 L/min. $ 51.80
50 GPM to
K be ordered
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
separately.
I
E GPM $ 97.30
100 L/min.
240 Options are: N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 • Solenoid Pilot Q 60 - 400 psi +$ 1.00
• Air Pilot
• Hydraulic Pilot W 150 - 4500 psi +$ 0.00
• Manual Control
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
c
6 (X)
2 6 1 5 (Y)
Port c
5
b
Port Locating (P) 3 1 (T)
Shoulder
Locating
Shoulder
Cartridge Dimensions
Cartridge Dimensions
4 Typical c Installation
Port Capacity Cartridge TypicalCavity a b Installation
Torque
Capacity Model Code Cartridge Cavity a bL C
c K Torque(lb. ft.)
a a Model Code (Nm)
3 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Port
2
40 L/min. DCCC – XCN T - 61A 84,8 22,2 50 40/50
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 80 L/min. DCDC – XCN T - 62A 92,2 28,6 59 60/70
2 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Port 160 L/min. DCEC – XCN T - 63A 114,4 31,8 73 200/215
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 320 L/min. DCFC – XCN T - 64A 139,7 41,3 92 465/500
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Port 1
Performance Curves
Performance Curves
RPCC RPEC RPGC RPIC RPKC
DCCC DCDC DCEC
Typical Pressure Rise
DCFC
5000 5000 Typical
5000 Pressure Drop 5000 5000
4000 4000 4000 4000
P = psi
4000
25 25 25 25
P = psi
P = psi
P = psi
P = psi
P to T P to T P to T
3000 3000 3000 3000 3000
20 P to A or B 20 P to A or B 20 20 All Flow Paths
P = bar
P = bar
P = bar
P = bar
2000 2000 2000 B to T 2000 P to A or B 2000
B to T Except A to T
14 14 14 B to T 14
1000 A to B Regen
1000 1000 A to B Regen 1000 1000
A to T A to T A to T A to T
7 7 7 0 40 80 120 160 7200
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
0 8 15 23 32 40 45 0 20 40 60 80 110 120 0 40 80 120 160 200 240 0 80 160 240 320 380 480
Q = L/min. ■ Maximum operating Q = L/min.
pressure = 5000 psi Q = L/min. Q = L/min.
■ Will accept maximum pressure at Port 2.
■
■
Maximum operating
Back pressure on thepressure
tank port=(port
350 bar
2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Maximum
Factory pressure settings established at 4atGPM
leakage per path = 2 in³/min. 1000 psi
■
■ Pilot volume for complete
Typical response time 10 ms. shift = DCCC: 0,33 cc/min., DCDC: 0,98 cc/min., DCEC: 2,8 cc/min.,
CFC: 6,9 cc/min.
■ Maximum leakage = RPCC, RPEC: 2 in /min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
3
■ Minimum pilotpsi,
in3/min./1000 pressure
RPKC:required to shift valve
5 in3/min./1000 psi. = DCCC: 12 bar, DCDC: 10,5 bar, DCEC, DCFC: 9 bar
■
■ All ports will accept 350 bar, including
RPCC minimum setting for all spring ranges the x and
is 75y psi
pilot ports (port 5 and port 6).
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DC ✱RP
C ✱ –C –X✱✱ ✱
✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range
Spool Configuration Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 Capacity
A 100 -(L/min.)
3000 psi +$ 0.00 N Buna-N +$ 0.00
C 40 L/min. C D E F N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
D 80 L/min. C 95,0 189,0 378,0 756,0 V Viton
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
E 160 L/min. I 100 GPM $ 97.30 T 38,0 N91,0 151,0
60 - 800 psi 378,0
+$ 1.00
F 320 L/min. K 200 GPM $187.00 H 38,0 Q95,0
60 - 400 +$ 1.00
psi 378,0
151,0
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
c (X) (Y)
2 1
6 6 5
Port c
5b Locating
Port Shoulder (P) 3 1 (T)
Locating
Shoulder
Cartridge Dimensions
Cartridge Dimensions
4 Typical c Installation
Capacity Cartridge Typical Cavity a b Installation
Torque
Port Capacity Model Code Cartridge Cavity a bL cC K Torque(lb. ft.)
a a Model Code (Nm)
3 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2
Port 40 L/min. DCCD – XCN T - 61A 84,8 22,2 50 40/50
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 80 L/min. DCDD – XCN T - 62A 92,2 28,6 59 60/70
2 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Port 160 L/min. DCED – XCN T - 63A 114,4 31,8 73 200/215
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 320 L/min. DCFD – XCN T - 64A 139,7 41,3 92 465/500
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Port 1
Performance Curves
Performance
RPCC Curves RPEC RPGC RPIC RPKC
DCCD DCDD DCED
Typical Pressure Rise
DCFD
5000 5000 Typical
5000 Pressure Drop 5000 5000
4000 4000 4000 4000
P = psi
4000
25 25 25 25
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
2000 2000 2000 P to A or B 2000
B to T Except A to T
14
1000 B to T 1000 14 1000 14 1000 B to T 14 1000
A to T A to T A to T A to T
7 0 5 10 15 20 25 0 10 7 20 30 40 50 0 20 40 7
60 80 100 0 40 80 120 160 7 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
0 8 15 23 32 40 45 0 20 40 60 80 110 120 0 40 80 120 160 200 240 0 80 160 240 320 380 480
Q = L/min. ■ Maximum operating Q = L/min.
pressure = 5000 psi Q = L/min. Q = L/min.
■ Will accept maximum pressure at Port 2.
■
■ Maximum operating
Back pressure on thepressure
tank port=(port
350 bar
2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Maximum
Factory pressure settings established at 4atGPM
leakage per path = 2 in³/min. 1000 psi
■■ Pilot volume for complete
Typical response time 10 ms. shift = DCCD: 0,82 cc/min., DCDD: 2,0 cc/min., DCED: 5,6 cc/min.,
■
DCFD: 14,0 cc/min.
Maximum leakage = RPCC, RPEC: 2 in /min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
3
■ Minimum pilotpsi,
in3/min./1000 pressure
RPKC: required to shift valve
5 in3/min./1000 psi. = 3 bar
■■ All
RPCCports will accept
minimum 350 for
setting bar,all
including the x and
spring ranges is 75y psi
pilot ports (port 5 and port 6).
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
DC ✱RP
D ✱ –C –X ✱✱ ✱
✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range
Spool Configuration Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 Capacity
A 100 -(L/min.)
3000 psi +$ 0.00 N Buna-N +$ 0.00
C 40 L/min. C D E F N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
D 80 L/min. G 50 GPM $ 51.80 K Handknob
C +$ 5.00
42,0 C83,0 170,0 340,0
150 - 6000 psi +$ 2.00
V Viton
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 2
2-position, 2-way Spool Directional Valve 114
1 1
2
2 Direct Acting, 2-position, 2-way Poppet
Directional Valve 115
1 1
Normally Open Normally Closed
2 2
2-position, 3-way Spool Directional Valve 116
1 3 3
1
Normally Closed
2 4
3 1
1 1
2 3 2 3
Performance Curves
RPCC RPEC RPGC
DLDA-M** RPIC RPKC
Valve Performance Limits
Typical Pressure Rise
Typical Performance
at 10% Undervoltage
Pressure Differential
5000 vs. Flow
5000 5000
and Stabilized Coil Temp.
5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
C (2 to 1)
3000 3000 350 3000 3000 3000
14 C (2 to 1)
2000 2000 2000 12 2000 C (1 to 2) 2000
P = bar
250
P = bar
10
1000 1000 1000 1000 1000
8 H (1 to 2)
150 H (2 to 1)
6 H (2 to 1)
0 5 10 15 20 25 0 10 20 30 40 50 0 H (1 to
202) 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
4
Flow = GPM
100
Flow = GPM Flow = GPM2 Flow = GPM Flow = GPM
C (1 to 2)
0 5 15 25 35
■ Maximum operating Q =pressure
L/min. =45 5000 psi 0 5 15 25
Q = L/min.
35 45
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
D LRP
D A✱ –C ✱– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal
Capacity Control Spool Configuration Coil
Capacity Control** Adjustment Range SealConfiguration*
D 40 L/min. M Manual H Normally Open ISO/DIN
C 12 GPM* $ 31.90 L Override
Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
212 12 VDC+$ 0.00
C Normally Closed 224 24 VDC
E 25 GPM $ 36.20 C No
X Tamper Resistant +$ 4.10
Manual B 50 - 1500 psi +$ 0.00 V Viton
211 115+$ VAC2.00
G 50 GPM $ 51.80 K Override
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 223 230 VAC
V W
Viton
150 - 4500 psi +$ 0.00 Twin Lead
712 12 VDC
724 24 VDC
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi. Deutsch
N Option is standard set at 400 psi. 912 12 VDC
Q Option is standard set at 200 psi. 924 24 VDC
948 48 VDC
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options +$ 1.10
Metri-Pack Customer may specify pressure setting.
Maximum Leakage (cc/min. at 210 bar 12 VDC 812
at 32 cSt oil) = 80 24 VDC 824
Power (Watts) = 22
Operating Voltage Tolerance = ± 10% * See page 167 for Solenoid Twin Spade
Visit www.sunhydraulics.com
Typical response Time (ms) = 50 for detailed and complete Connector
technical information
Options on our full line524
of products.
24 VDC
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
350 350 20 20
P = psi
P = psi
P = psi
3000 DTDA-MCN
3000 DTDA-MHN
3000 3000 3000
250 1 to 2 250 15 15
P = bar
2 to 1
P = bar
P = bar
P = bar
2000 2000 2000 2000
DTDA-MHN 2000 DTDA-MCN
150 150 10 1000 10 1000
1000 1000 1000
50 DTDA-MCN 50 DTDA-MHN 5 0 40 80 120 160 5 200
0 5 10 15 20 25 0 10 20 30 140
to 2 50 0 20 40 60 80 100 0 80 160 240 320 400
2 to 1
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
0 10 20 30 40 50 60 0 10 20 30 40 50 60 0 10 20 30 40 50 60 0 10 20 30 40 50 60
Q■= L/min. Q = L/min. Q = L/min. Q = L/min.
Maximum operating pressure = 5000 psi
■
■ Will
Maximumaccept operating
maximumpressure pressure=at350 Port 2.
bar**
■■ Back pressure on the tank
Maximum Leakage at 32 cSt = 10 drops/min. port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■■ Switching
Factory frequency
pressure settings = 15000 cycles/hr.
established at 4 GPM
■
■ Proper installation
Typical response time of solenoid
10 ms. valves requires an extra deep socket to clear the solenoid tube.
Sockets are available from Snap On tools (P/N SIML280) or Sun Hydraulics (P/N 998-100-006).
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
See
in www.sunhydraulics.com
3/min./1000 psi, RPKC: 5 in for details. psi.
3/min./1000
** For valves produced before January 1, 2004 (date code A041), the maximum operating pressure is
■ RPCC minimum
350 bar at port 2 and 250 barsetting for all
at port 1. NOTE: spring
While the valveranges
will operateis 75 psi
reliably with pressures up
to 350 bar at Port 1, solenoid tube fatigue life is reduced.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
D TRP
DA C ✱– ✱✱ ✱✱ –
✱– ✱ ✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control Spool Configuration Coil Configuration*
D C 12 GPM*
40 L/min. $ 31.90 L
M Manual Screw +$ 0.00 H A
Standard Openpsi +$ 0.00
100 - 3000
Normally N Buna-N ISO/DIN
+$ 0.00
Override 212 12 VDC
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 C B 50 - 1500
Normally psi
Closed +$ 0.00 V Viton
224 24 +$ VDC2.00
G 50 GPM $ 51.80 X
K No Manual
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 211 115 VAC
Override 223 230 VAC
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
AMP® Junior Timer
K 200 GPM $187.00 Q 60 - 400Seal
psi +$ 1.00 612 12 VDC
624 24 VDC
N W
Buna-N
150 - 4500 psi +$ 0.00
Twin Lead
V Viton 712 12 VDC
Adjustment Range Options: 724 24 VDC
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi. Deutsch
Q Option is standard set at 200 psi. 912 12 VDC
924 24 VDC
** See page 162 for information * Minimum setting 75 psi on all ranges.948 48 VDC
on Control Options Customer may specify pressure setting. +$ 1.10
Metri-Pack
812 12 VDC
824 24 VDC
Power (Watts) = 22
Operating Visit www.sunhydraulics.com
Voltage Tolerance = ± 10% for detailed and complete
* technical information
See page 167 on our full line of products.
for Solenoid Twin Spade
Typical response Time (ms) = 50 6
Connector Options 524 24 US VDC
Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b 1 3
Normally
Locating
c Shoulder Open 1 3
Cartridge Dimensions
Cartridge Dimensions
Typical c Installation
Capacity
Nominal Cartridge Typical Cavity a b Installation
Torque
b Capacity Model Code Cartridge Cavity a b L c C d K Torque
(lb. ft.)
a Model Code (Nm)
12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
3 40 L/min. DMDA – MNN T - 11A 34,9 22,4 109 38 40/50
2 Locating
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Shoulder
Outlet Port
a 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
2
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Port
Inlet 1
Port 1 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC RPEC RPGC
DMDA-MNN RPIC RPKC
Valve Performance Limits at 10% Undervoltage Typical Pressure Rise Typical Performance
5000 and Stabilized
5000 Coil Temperature 5000 5000Pressure Differential vs. Flow
5000
Spool Option A 4000 Spool Option N4000 Spool Option
4000 A Spool
4000 Option N
P = psi
4000
P = psi
P = psi
P = psi
P = psi
250 & (2 to 3)
P = bar
P = bar
10 (1 to 2) 10
(2 to 1)
1000 1000 1000 8 1000 8 1000
150 150 (1 to 2)
6 6
(3 to 2) & (2 to 1) (2 to 1)
0 100 5 10 15 20 25 0 10 20
100 30 40 50 0 (2 to20
3) 40 60 4 80 100 0 40 80 120 4
160 200 0 80 160 240 320 400
(2 to 3)
Flow = GPM Flow = GPM Flow = GPM 2 Flow = GPM 2
Flow = GPM
0 5 15 25 35 45 0 5 15 25 35 45 0 5 15 25 35 45 0 5 15 25 35 45
Q = L/min.■ Maximum operating Q =pressure
L/min. = 5000 psi Q = L/min. Q = L/min.
■
■
Will
Maximumacceptoperating
maximumpressure pressure= at 350Port 2.
bar**
■
■ Back pressure on the tank
Maximum Leakage at 32 cSt = 81,9 cc/min.@210 port (port 2) is directly additivebar at a 1:1 ratio to the valve setting.
■ Factory
Switching pressure
frequency settings
= 15000 established
cycles/hr at 4 GPM
■
■ Proper installation
Typical response time of solenoid
10 ms. valves requires an extra deep socket to clear the solenoid tube.
■ Maximum leakage = RPCC,Snap
Sockets are available from RPEC:On tools (P/N SIML280)
2 in 3/min./1000 or Sun3Hydraulics
psi, RPGC: in3/min./1000 (P/Npsi,998-100-006).
RPIC: 4
See
in 3/min./1000 psi, RPKC: 5 infor
www.sunhydraulics.com details. psi.
3/min./1000
**For valves produced before January 1, 2004 (date code A041), the maximum operating pressure is 350 bar at ports 2 and 3 and 250 bar at port 1.
■ RPCC
NOTE: Whileminimum setting
the valve will operate forwith
reliably allpressures
spring ranges
up to 350 bar atis
Port75 psi tube fatigue life is reduced.
1, solenoid
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
D MRP
D A✱ –C ✱– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal
Capacity Control Spool Configuration Coil Configuration*
Capacity Control** Adjustment Range Seal
D 40 L/min. M Manual A Normally Open ISO/DIN
C 12 GPM* $ 31.90 L Override
Standard Screw +$ 0.00 A 100
Ports 1 psi +$ 0.00
- 3000
2 to N Buna-N
212 12 VDC+$ 0.00
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 224 24 VDC
V Viton +$ 2.00
X No manual N Normally Open 211 115 VAC
G 50 GPM $ 51.80 K Override
Handknob +$ 5.00 C 150
Ports 2 to 3 psi
- 6000 +$ 2.00 223 230 VAC
I 100 GPM $ 97.30 N 60 - 800
Sealpsi +$ 1.00 AMP® Junior Timer
612 12 VDC
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00 624 24 VDC
N Buna-N
W 150 - 4500 psi +$ 0.00 Twin Lead
V Viton 712 12 VDC
724 24 VDC
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi. Deutsch
N Option is standard set at 400 psi. 912 12 VDC
Q Option is standard set at 200 psi. 924 24 VDC
** See page 162 for information * Minimum setting 75 psi on all ranges.948 48 VDC
on Control Options Customer may specify pressure setting. +$ 1.10
Metri-Pack
Maximum Leakage (cc/min. at 210 bar 812 12 VDC
at 32 cSt oil) = 80 824 24 VDC
Power (Watts) = 22
Operating Voltage Tolerance = ± 10% * See page 167 for Solenoid Twin Spade
Visit www.sunhydraulics.com
Typical response Time (ms) = 30-50 for detailed and complete Connector
technical information
Options on our full line of products.
524 24 VDC
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Locating Normally
Shoulder
Closed Cartridge Dimensions
c
Typical c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
3 1
b a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Locating
2 Cartridge Dimensions
Shoulder 25 GPM RPEC – LAN
Typical
T - 10A 1.56 7/8” 2.00 2.06 2.2530/35
Installation
Outlet 4 Nominal
Port
50 GPM
Capacity RPGC – LAN
CartridgeT - 3A Cavity
1.88 a1 1/8” b 2.12 c 2.18 d Torque
2.3845/50
Model Code (Nm)
3 a 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet
Port 1 28-45 L/min. DNDA – MCN T - 31A 34,9 22,4 90 38 40/50
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
2
Port
Performance Curves
RPCC 1 Port RPEC RPGC RPIC RPKC
Performance Curves Typical Pressure Rise
5000 5000 5000 DNDA-MCN 5000 5000
4000 4000 4000 4000
P = psi
4000
Valve Performance Limits at 10% Undervoltage Typical Performance Pressure
P = psi
P = psi
P = psi
P = psi
Not Shifted
P = bar
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
D NRP
DA C ✱– ✱✱ ✱✱ –
✱– ✱ ✱✱✱
Nominal
Nominal
Capacity Control SpoolAdjustment
Configuration Coil
Capacity Control** Range SealConfiguration*
D 28-45 L/min. M Manual C ISO/DIN
C 12 GPM* $ 31.90 L Standard
Override Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
212 12 +$ VDC0.00
D 224 24 VDC
E 25 GPM $ 36.20 C Tamper
X Resistant +$ 4.10 B 50 - 1500 psi
No manual +$ 0.00 V Viton
211 115+$ VAC2.00
G 50 GPM $ 51.80 Override
K Handknob E
+$ 5.00 C 150 - 6000 psi +$ 2.00 223 230 VAC
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c 1
Normally
b c Open
DAAA-MHN 1
Locating Cartridge Dimensions
Shoulder
Typical Cartridge Dimensions
c Installation
Nominal Cartridge Cavity a b d Torque
Typical c Installation
Capacity
Capacity Model Code
Cartridge Cavity a b M C (Nm)Torque
Model Code L C K (lb. ft.)
b a
Locating 1 L/min. DAAA – MCN T - 8A 19,1 22,4 75 80 31 35/40
Shoulder 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 1 L/min. DAAA – MHN T - 8A 19,1 22,4 75 80 31 35/40
a 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
2 1 L/min. DAAC – MCN T - 8A 19,1 22,4 75 80 31 35/40
Port 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Port 1 1 L/min. DAAC – MHNT - 16A
T - 8A 19,1 22,4 75 80 31 35/40
100 GPM RPIC – LAN 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC RPEC DAA*-M*N
RPGC RPIC RPKC
Pressure
Typical vs. Flow
Pressure Rise
5000 35
5000 5000 5000
5000
4000 25
4000 4000 4000
P = psi
4000
P = bar
P = psi
P = psi
P = psi
P = psi
3000 3000 20
3000 3000 3000
2000 2000 14
2000 2000 2000
1000 1000 7
1000 1000 1000
0 5 10 15 20 25 0 10 20 30 40 50 00 0.820 1.540 2.460 3.6 80 4100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM QFlow = GPM
= L/min. Flow = GPM Flow = GPM
D ARP
A ✱✱ –C ✱– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control Spool Configuration Coil Configuration*
A C 12 GPM*
1 L/min. $ 31.90 ML Manual
Standard Screw +$ 0.00H A 100 - 3000
Normally Openpsi +$ 0.00 N Buna-N ISO/DIN
+$ 0.00
E 25 GPM $ 36.20 C Override
Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V 206
Viton 6 VDC
+$ 2.00
C Normally Closed 212 12 VDC
G 50 GPM $ 51.80 CK Concealed
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 224 24 VDC
Override 211 115 VAC
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00 223 230 VAC
K 200 GPM $187.00 Version Q 60 - 400Seal
psi +$ 1.00
SAE J858
A Standard N Buna-N
W 150 - 4500 psi +$ 0.00 506 6 VDC
512 12 VDC
C Canadian V Viton 524 24 VDC
Standards Adjustment Range Options:
Association A, B, C, and W are standard set at 1000 psi. Twin Lead
Certified N Option is standard set at 400 psi. 706 6 VDC
240 bar max. Q Option is standard set at 200 psi. 712 12 VDC
** See page 162 for information 724 24 VDC
* Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
D BRP
A ✱✱ –C ✱– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control Spool Configuration Coil Configuration*
A C 12 GPM* $ 31.90
1 L/min. L Manual
M Standard Screw +$ 0.00H Normally
A 100 - 3000
Openpsi +$ 0.00 N Buna-N ISO/DIN
+$ 0.00
E 25 GPM $ 36.20
Override Ports 1 to 2
C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00
206 6 VDC
V Viton +$ 2.00
212 12 VDC
G 50 GPM $ 51.80 CK Concealed
Handknob +$ 5.00C Normally
C 150 - 6000
Openpsi +$ 2.00 224 24 VDC
Override Ports 1 to 3 211 115 VAC
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00 223 230 VAC
K 200 GPM $187.00 Version Sealpsi
Q 60 - 400 +$ 1.00
SAE J858
A Standard N Buna-N
W 150 - 4500 psi +$ 0.00 506 6 VDC
512 12 VDC
C Canadian V Viton 524 24 VDC
Standards Adjustment Range Options:
Association A, B, C, and W are standard set at 1000 psi. Twin Lead
Certified N Option is standard set at 400 psi. 706 6 VDC
240 bar max. Q Option is standard set at 200 psi. 712 12 VDC
724 24 VDC
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Air Pilot
2 1
c 1
Normally
b c Open
DAAA-MHN 1
Locating Cartridge Dimensions
Shoulder
Typical Cartridge Dimensions
c Installation
Capacity Cartridge
Typical Cavity a b c d Torque
Installation
Capacity Model Code
Cartridge Cavity a b M C (Nm)Torque
Model Code L C K (lb. ft.)
b a
Locating 1 L/min. DAAA – MCN T - 8A 19,1 22,4 75 80 31 35/40
Shoulder 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 1 L/min. DAAA – MHN T - 8A 19,1 22,4 75 80 31 35/40
a 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
2 1 L/min. DAAC – MCN T - 8A 19,1 22,4 75 80 31 35/40
Port 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Port 1 1 L/min. DAAC – MHNT - 16A
T - 8A 19,1 22,4 75 80 31 35/40
100 GPM RPIC – LAN 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC RPEC DAA*-M*N
RPGC RPIC RPKC
Pressure
Typical vs. Flow
Pressure Rise
5000 35
5000 5000 5000
5000
4000 25
4000 4000 4000
P = psi
4000
P = bar
P = psi
P = psi
P = psi
P = psi
3000 3000 20
3000 3000 3000
2000 2000 14
2000 2000 2000
1000 1000 7
1000 1000 1000
0 5 10 15 20 25 0 10 20 30 40 50 0 0 0.8 20 1.5 40 2.4 60 3.6 80 4 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Q Flow = GPM
= L/min. Flow = GPM Flow = GPM
D ARP
A A✱ –C M– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control Spool Configuration Coil Configuration*
A C 12 GPM*
1 L/min. $ 31.90 ML Manual
Standard Screw +$ 0.00H A 100 - 3000
Normally Openpsi +$ 0.00 N Buna-N ISO/DIN
+$ 0.00
E 25 GPM $ 36.20 C Override
Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V 206
Viton 6 VDC
+$ 2.00
C Normally Closed 212 12 VDC
G 50 GPM $ 51.80 CK Concealed
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 224 24 VDC
Override 211 115 VAC
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00 223 230 VAC
K 200 GPM $187.00 Version Seal
Q 60 - 400 psi +$ 1.00
SAE J858
A Standard N Buna-N
W 150 - 4500 psi +$ 0.00 506 6 VDC
512 12 VDC
C Canadian V Viton 524 24 VDC
Standards Adjustment Range Options:
Association A, B, C, and W are standard set at 1000 psi. Twin Lead
Certified N Option is standard set at 400 psi. 706 6 VDC
240 bar max. Q Option is standard set at 200 psi. 712 12 VDC
** See page 162 for information 724 24 VDC
* Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
1
2 Normally 1 Ext.
cc Closed
bb DAAH-*HN
1
4000
P = psi
P = psi
P = psi
P = psi
■
■ Maximum operating
Maximum operating pressure
pressure == 350
5000bar
psi
■ Will accept maximum pressure at Port 2.
■ Maximum leakage at 32 cSt = 0,6 cc/min at 350 bar.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Minimum pilot pressure to operate = 14 bar
■ Factory pressure settings established at 4 GPM
■ All ports will accept 350 bar including the pilot control port.
■ Typical response time 10 ms.
■ The preferred flow path through the valve is port 2 to port 1.
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ The
in /min./1000 psi, RPKC: 5 in /min./1000 psi.to the correct torque value followed by the T-8A pilot
3 main stage valve should first
3 be installed
■ control section into
RPCC minimum the main
setting stage
for all valve
spring to itsisrequired
ranges 75 psi torque value.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP A
DA ✱HC –
– ✱
✱ ✱
✱✱✱
Nominal
Capacity Control** Adjustment Range Seal
Nominal Pilot Port Spool Configuration Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 1 L/min. A 1/8-27 NPTF H Normally Open N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K SAE-4
B Handknob +$ 5.00 C Normally
150 - 6000Closed
psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
D 1/8-28 BSPP
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
UK Shortcut Catalogue #999-901-244 123
Pilot Control Valves
AIR-OPERATED, 2-POSITION 2-WAY, SPOOL DIRECTIONAL
VALVE - PILOT CAPACITY
Relief Valves 2 Normally
Closed
PILOT OPERATED, BALANCED
Ext.
PISTON
DAAP-*CN
2
Full Adjustment 5 Turns
+ -
1
Ext.
c Normally
b 2 Open 1
DAAP-*HN 1
c
b Cartridge Dimensions
Locating
Shoulder Typical Installation
Locating Capacity Cartridge Cavity a b c Torque
Shoulder Model Code (Nm)
2
a Cartridge Dimensions
1 L/min. DAAP – FCN
Typical T - 8A 19,1 22,2 c 42,2 35/40
Installation
Port
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
1 Port a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance Curves 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN DAAP
T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
5000
145000 5000 5000
5000
4000 74000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
DA ACP –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Pilot Port Spool Configuration Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 1 L/min. E SAE-4 H Normally Open N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 F Handknob
K 1/8-27 NPTF +$ 5.00 C 150
C Normally
- 6000Closed
psi +$ 2.00 V Viton
I 100 GPM $ 97.30 P 1/8-28 BSPP N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
124 UK Shortcut Catalogue #999-901-244
6 US Shortcut Catalogue #999-901-243
Pilot Control Valves
MANUALLY OPERATED, 2-POSITION 2-WAY, SPOOL DIRECTIONAL
Relief
VALVE Valves
- PILOT CAPACITY
PILOT OPERATED, BALANCED PISTON
d 5 Turns D Control L Control T Control
Full Adjustment 1 1 1
+ -
H Spool:
Normally
2 Open 1
c 2 2 2 = Twist (Momentary)
b 1 1 1 = Lock (Detent)
C Spool:
Locating Normally
Shoulder
c Closed Cartridge Dimensions
Typical c Installation
Capacity 2 Cartridge 2 Cavity 2 a b Torque
b Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Cartridge Dimensions
2 25 GPM RPEC – LANTypicalT - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet Installation
2 a Capacity RPGC – LAN
Cartridge Cavity a b2.12 c 2.18 d
50 GPM T - 3A 1.88 1 1/8” 2.38 Torque 45/50
Port Model Code (Nm)
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet1 1Port Locating 1 L/min. DAAM - TCN T-8A 19,1 28,6 61 35,6 35/40
Shoulder 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC RPEC RPGC RPIC RPKC
Typical DAAM
Pressure Rise
5000 5000 5000 5000
5000
4000
Pressure vs. Flow
4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = barP = psi
3000 3000 35
3000 3000 3000
2000 2000 25
2000 2000 2000
1000 1000 1000
20 1000 1000
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP AC
DA ✱ M – ✱ ✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Pilot Port Spool Configuration Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 1 L/min. D Dual C Normally Closed N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
(Twist/Lock) B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 H 150
C Normally
- 6000 Open
psi +$ 2.00 V Viton
L Lock (Detent)
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 T Twist Q 60 - 400 psi +$ 1.00
(Momentary)
W 150 - 4500 psi +$ 0.00
NOTE: Designed for 10,000
cycles of operation maximum
Adjustment Range Options:
under normal conditions.
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical US Shortcut Catalogue #999-901-243
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
D BRP
A A✱ –C M– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control Spool Configuration Coil Configuration*
A C 12 GPM*
1 L/min $ 31.90 ML Manual
Standard Screw +$ 0.00H Normally
A 100 - 3000
Openpsi +$ 0.00 N Buna-N ISO/DIN
+$ 0.00
Override Ports 1 to 2 206 6 VDC
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V 212 +$ 2.00
Viton 12 VDC
G 50 GPM $ 51.80 CK Concealed
Handknob +$ 5.00C Normally Openpsi
C 150 - 6000 +$ 2.00 224 24 VDC
Override Ports 1 to 3 211 115 VAC
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00 223 230 VAC
Version Seal
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
SAE J858
A Standard N Buna-N 506 6 VDC
W 150 - 4500 psi +$ 0.00 512 12 VDC
C Canadian V Viton 524 24 VDC
Standards Adjustment Range Options:
Association A, B, C, and W are standard set at 1000 psi. Twin Lead
Certified 706 6 VDC
N Option is standard set at 400 psi.
240 bar max. 712 12 VDC
Q Option is standard set at 200 psi. 724 24 VDC
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Maximum Leakage (drops/min. at 350 bar 6 US Shortcut Catalogue #999-901-243
* See page 167 for at 32 cSt / 43° C) = 10
Solenoid Connector Diameter Effective Orifice (mm) = 1,1 Power (Watts) = 12
Options Operating Voltage Tolerance = ± 10% Typical response Time (ms) = 30
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP AC
DB ✱ H –
– ✱
✱ ✱
✱✱✱
Nominal
Capacity Control** Adjustment Range Seal
Nominal Pilot Port Spool Configuration Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
A 1 L/min. A 1/8-27 NPTF H Normally Open N Buna-N
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 1 to 2psi +$ 2.00
Ports- 6000
I 100 GPM $ 97.30 B SAE-4 N 60 - 800 psi +$ 1.00 V Viton
C Normally Open
K 200 GPM $187.00 D 1/8-28 BSPP Q 60 - 400
Ports 1 topsi
3 +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Maximum operating
Factory pressure pressure
settings = 350 bar
established at 4 GPM
■
■ Maximum leakagetime
Typical response at 32
10cSt
ms.= 0,6 cc/min. at 350 bar
■
■ Maximum
Maximum pilot pressure
leakage = RPCC,= 5 bar
RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Minimum pilotpsi,
in3/min./1000 pressure
RPKC:to5operate = 1,5 bar
in3/min./1000 + port 1 pressure/7 bar
psi.
■
■ All ports will accept 350 bar with the exception
RPCC minimum setting for all spring ranges is 75 of psi
the pilot port which accepts 35 bar maximum.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
D B C P
✱A – ✱ ✱ ✱
– ✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Pilot Port Spool Configuration Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 1 L/min. E SAE-4 H Normally Open N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B Ports
50 - 1500
1 to 2psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 F
K 1/8-27 NPTF
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
C Normally Open
I 100 GPM $ 97.30 P 1/8-28 BSPP N Ports
60 - 800
1 topsi
3 +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
DBAM
3000 3000 3000 3000 3000
2000 2000 2000 2000 2000
1000 1000
Pressure vs. Flow
1000 1000 1000
20
■ Will accept maximum pressure 14 at Port 2.
■ Back pressure on the tank port 7 (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure settings established
0 0.8 at 42.4GPM
1.5 3.6 4
Q = L/min.
■ Typical response time 10 ms.
■
■ Maximum leakage
Maximum operating= pressure
RPCC, RPEC: = 350 2bar in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Maximum
in leakage
3/min./1000 at 32 cSt
psi, RPKC: 5 in=30,6 cc/min. psi.
/min./1000 at 350 bar
■
■ All ports
RPCC will accept
minimum 350for
setting bar.all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
D ✱BC
A –
M✱– ✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Pilot Port Spool Configuration Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 1 L/min. D Dual C Normally N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
(Twist/Lock) B 50 - 1500
Open 1-3 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
L Lock (Detent) H Normally
I 100 GPM $ 97.30 N 60 - 800
Open 1-2psi +$ 1.00
K 200 GPM $187.00 T Twist Q 60 - 400 psi +$ 1.00
(Momentary)
W 150 - 4500 psi +$ 0.00
NOTE: Designed for 10,000
cycles of operation maximum
Adjustment Range Options:
under normal conditions.
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
R ✱BC
A –
E ✱
– ✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 10 L/min. L Standard Screw A 2 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 C Handknob
K Concealed +$ 5.00 B 150
C 2 - 105 bar psi
- 6000 +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K Handknob C 2 - 420 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
D 2 - 55 bar
W 150 - 4500 psi +$ 0.00
E 2 - 25 bar
Adjustment Range Options:
W B,
A, 2 C,
- 315
andbar
W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Adjustment Range Options:
6 US Shortcut Catalogue #999-901-243
A, B, C, and W are standard set at 70 bar.
** See page 162 for information D Option is standard set at 25 bar.
on Control Options E Option is standard set at 14 bar.
Customer may specify pressure setting.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c 2 1
b c
Locating
b Shoulder
Cartridge Dimensions
Cartridge Dimensions
Typical Typical c Installation
Installation
Capacity CartridgeCartridge Cavity Cavity a
Capacity ab b c Torque
Torque
Locating Model Code
Model Code L C K (Nm)(lb. ft.)
aShoulder
10 L/min.RPCC – RBAR
12 GPM LAN – AWN T - 162A T - 8A
1.22 3/4”
19,1 2.11
22,2 2.1741 2.31 35/4025/30
2
Outlet 10 L/min.RPEC – RBAR
25 GPM LAN – AYN
T - 10A T - 8A
1.56 7/8”
19,1 2.00
28,6 2.0641 2.25 30/35
35/40
a 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
2
Port 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
Port 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC RPEC RPGC RPIC RPKC
RBAR
Typical Pressure Rise
Air to Oil at 0,4 L/min. Pressure vs. Flow
5000 5000 420 5000 420 5000 5 bar Air 5000
350
Hydraulic
4000
P = psi
P = bar
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP BC
R ✱ A –R ✱
– ✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Port Air Pilot Ratio Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 10 L/min. A 1/8-27 NPTF W 50:1 N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
Pilot Port B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 Y 150
C 75:1- 6000 psi +$ 2.00 V Viton
B SAE-4 Pilot Port
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 D 1/8-28 BSPP Port Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c
b Control Valves
Pilot
FULLY ADJUSTABLE
Locating
Shoulder NEEDLE VALVE - PILOT CAPACITY
Cartridge Dimensions
Typical c Installation
Capacity
2 Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 c
b 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP
N ✱FC
A –
B ✱– ✱K ✱X ✱
Nominal
Capacity Control** Adjustment Range Seal
Model
Control Maximum Orifice Seal
C Code
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
NFAB-KXN
E 25 GPM $ 36.20 K Tamper
C Resistant +$ 4.10
Handknob X 50
B 0,9-mm
1500 psi +$ 0.00 N Viton
V Buna-N +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
P = bar
200 200
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
RB ACP – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 1 L/min. M Manual Override A 20 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
(Standard) B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 B
C 10 - -105
150 barpsi
6000 +$ 2.00 V Viton
NOTE: Coil must be
I 100 GPM $ 97.30 ordered separately. Use N
W 60
35 - 800
350 psi
bar +$ 1.00
K 200 GPM $187.00 12V DC or 24V DC Q 60 - 400 psi +$ 1.00
(Series 770-***) coils
only. See page 167. W 150 - 4500 psi +$ 0.00
Ext. 2
Ext. 2
3 2
2 4
Low Side, 3-position, Hot Oil Shuttle
140
Valve
2 4
4 2
Spring Offset, 2-position, High Side
142
Shuttle
4000
P = psi
P = psi
P = psi
P = psi
CSAW/CSAY CSAA/CSAC2000
3000 3000 3000 3000 3000
2000 2000 2000 2000
1000 1000 1000
Typical Pressure Drop
1000 1000
■ Maximum operating
15 pressure = 5000 psi 12
10
■ Will accept maximum pressure at Port 2. 8
5 4
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
0 1,0 2,0 3,0 4,0 5,0 6,0 7,0 0 5 10 15 20
■ Factory pressure settings Q =established
L/min. at 4 GPM Q = L/min.
■ Typical response time 10 ms.
■
■ Maximum leakage
Maximum operating= pressure
RPCC, RPEC: = 350 bar2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Maximum valve leakage = 0,4 cc/min.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP AC
CS ✱ ✱ – ✱ ✱
X ✱
Nominal
CapacityNominal Capacity Control** Adjustment Range
Control
Seal
Seal
and Version
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
W 5 L/min. .25 BSPP External B N Buna-N
E 25 GPM
Signal $ 36.20
at External Port C Tamper Resistant +$ 4.10PortB 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
Y 5 L/min. E SAE-4 External
I 100 GPM
Signal at Port$2 97.30 PortN 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
A 10 L/min.
Signal at External Port W 150 - 4500 psi +$ 0.00
C 10 L/min.
Adjustment Range Options:
Signal at Port 2
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c
b
b 1 2 1 3
Locating
Shoulder
c Cartridge Dimensions
Typical 3 2 c Installation
3 Capacity Cartridge Cavity a b Torque
Locating L C K
Port Shoulder CSAX/CSAB Code
Model CSAD/CSAZ (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 Cartridge2.00
7/8” Dimensions
2.06 2.25 30/35
Outlet Typical Installation
a Nominal RPGC – LAN
50 GPM CartridgeT - 3A 1.88
Cavity 1 1/8”
a 2.12
b 2.18
c 2.38 Torque45/50
2 Capacity
100 GPM Model Code
RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 (Nm)150/160
Port Inlet 1
5 L/min. RPKC –CSAX
200 GPM LAN – XXNT - 18A T - 163A
3.13 1 31
5/8” 19,1
2.81 32
2.94 3.06 35/40
350/375
1 Port 5 L/min. CSAZ – XXN T - 163A 31 19,1 31,8 35/40
Performance Curves
10 L/min. CSAB – XXN T - 11A 34,9 22,2 31 40/50
RPCC RPEC RPGC RPIC RPKC
10 L/min. CSAD – XXN T - 11A 35,1 22,2 30,2 40/50
Typical Pressure Rise
Performance
5000 Curves 5000 5000 5000 5000
4000 4000 4000 4000
P = psi
4000 P = psi
P = psi
P = psi
P = psi
3000 3000
CSAX/CSAZ 3000
CSAB/CSAD 3000
2000
3000
2000 2000 2000 2000
1000 1000
Typical
1000
Pressure Drop 1000 1000
0 5 10 15 20 25 0 10 20 2530 40 50 0 20 40 60
20 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow =20GPM Flow = GPM Flow = GPM Flow = GPM
16
P = bar
P = bar
■ Maximum operating
15 pressure = 5000 psi 12
10 8
■ Will accept maximum
5
pressure at Port 2. 4
■ Back pressure on0 the tank port (port 2) is directly
1,0 2,0 3,0 4,0 5,0 6,0 7,0 0 5
additive
10
at a 1:1
15 20
ratio to the valve setting.
■ Factory pressure settings Q = established
L/min. at 4 GPM Q = L/min.
■ Typical response time 10 ms.
■
■ Maximum
Maximum operating
leakage = pressure
RPCC, RPEC: = 350 bar 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Maximum valve leakage = 0,4 cc/min.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP A
CS ✱✱C –
– ✱
X ✱
X ✱
✱
Nominal
CapacityNominal Capacity Control** Adjustment Range Seal
Control Seal
and Version
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
X 5 L/min. X Non-adjustable N Buna-N
E 25 GPM
Signal at Port$3 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
Z 5 L/min.
I 100 GPM
Signal at Port$2 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
B 10 L/min.
Signal at Port 3 W 150 - 4500 psi +$ 0.00
D 10 L/min.
Adjustment Range Options:
Signal at Port 2 A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
12 21 1 Ext.
b c
b c
Locating Ext. 2
Locating
Shoulder
Shoulder CDAA CDAC
Cartridge Dimensions
a Typical Cartridge Dimensionsc Installation
Capacity Cartridge Cavity a b Torque
2 Model CodeTypical L C K Installation
(lb. ft.)
Nominal Cartridge Cavity a b c Torque
Port a Capacity RPCC – LAN
12 GPM T - 162A 1.22 3/4” 2.11 2.17 2.31 (Nm)25/30
Model Code
2
Port 1
Outlet 10 L/min. RPEC –CDAA
25 GPM LAN – BBN
T - 10A T - 13A
1.56 7/8”
35,1 2.00
22,2 2.06
30,2 2.25 40/5030/35
50 GPM
10 L/min. RPGC – LAN T
CDAC – BBN- 3A 1.88
T - 13A 135,1
1/8” 2.12
22,2 2.18
19 2.38 40/5045/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance
RPCC Curves RPEC RPGC RPIC RPKC
CDAA/CDAC
Typical Pressure Rise
4000
P = psi
P = psi
P = psi
P = psi
30
3000 3000 3000 3000 3000
24 2000
2000 2000 2000
P = bar
2000
1000 1000
18
1000 1000 1000
12
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM 6 Flow = GPM Flow = GPM Flow = GPM
0 5 10 15 20
■ Maximum operating pressure = 5000 Qpsi
= L/min.
■ Will accept maximum pressure at Port 2.
■
■ Maximum operating
Back pressure on thepressure
tank port=(port
350 bar
2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure
Maximum settings =established
valve leakage 0,4 cc/min.at 4 GPM
■
■ Typical
The response time
back-to-back 10 do
checks ms.not provide a means of lowering a signal. They will trap a high signal if
■ the load pressures
Maximum leakagedrop to a lower
= RPCC, RPEC:pressure. Some means
2 in 3/min./1000 of bleeding
psi, RPGC: 3 in3off the signalpsi,
/min./1000 should be4provided.
RPIC:
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ 1,0 bar check.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP A
CD ✱✱C –
– ✱
✱ B
✱✱✱
Nominal
Nominal Capacity
Capacity Control** Adjustment Range Seal
and Version$ 31.90 Control Seal
C 12 GPM* L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 10 L/min. B .25 BSPP N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
Signal at External External Port
G Port
50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
C 10 L/min. E SAE-4
K 200 GPM
Signal at $187.00 Q External
60 - 400 Port
psi +$ 1.00
Port 2
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
21 1
2 1 3
b c
b
c 3 2
Locating
3 Shoulder CDAB CDAD
Port Locating Cartridge Dimensions
Shoulder Typical c Installation
Capacity Cartridge Cavity a b Cartridge Dimensions Torque
Model Code L C K (lb. ft.)
a a Nominal RPCC – LAN Typical Installation
2 12 GPM CartridgeT - 162A 1.22
Cavity 3/4”
a 2.11
b 2.17
c 2.31 Torque25/30
2 Capacity Model Code (Nm)30/35
Port 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25
Outlet 10 L/min. RPGC –CDAB
50 GPM LAN – XBN
T - 3A T - 11A
1.88 135,1
1/8” 22,2
2.12 30,2
2.18 2.38 40/5045/50
Port 1 10 L/min. RPIC –CDAD
100 GPM LAN – XBN
T - 16A T - 11A
2.44 135,1
1/4” 22,2
2.44 30,2
2.47 2.69 40/50
150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
RPCC
Performance Curves RPEC RPGC RPIC RPKC
Typical Pressure Rise
CDAB/CDAD 5000 5000
5000 5000 5000
4000
Typical
4000
Pressure Drop 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = bar P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP A
CD ✱✱C –
– ✱ ✱✱
X B ✱
Nominal
Nominal Capacity
Capacity Control** Adjustment Range Seal
and Version Control Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 10 L/min. X Non-adjustable N Buna-N
E 25 GPM
Signal at Port$3 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
D 10 L/min.
I 100 GPM
Signal at Port$2 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b c 2 1
c
Locating
Shoulder
b
3
Locating
4 Shoulder
Cartridge Dimensions
Port
a Typical Cartridge Dimensionsc Installation
Capacity Cartridge
3 Typical Cavity
Nominal Model CodeCartridge
a b
L C
Torque
K Installation
(lb. ft.)
Port a Capacity RPCC – LAN Cavity a b c Torque
12 GPM T - 162A
Model Code 1.22 3/4” 2.11 2.17 2.31 (Nm)25/30
22 60 L/min. RPEC –DSCH
25 GPM LAN – XHN
T - 10A T - 31A
1.56 7/8”
84,8 2.00
22,2 2.06
30 2.25 40/5030/35
Outlet
Port
GPML/min.RPGC –DSEH
50 120 LAN – XHN
T - 3A T - 32A
1.88 1 92,2
1/8” 2.12
28,6 2.18
34 2.38 60/7045/50
100240
GPML/min.RPIC –DSGH
LAN – XHN
T - 16A T - 33A
2.44 1114,4
1/4” 2.44
31,8 2.47
42 2.69 200/215
150/160
Inlet 1 1Not Used
Port
200480
GPML/min.RPKC –DSIH
LAN – XHN
T - 18A T - 34A
3.13 1139,7
5/8” 2.81
41,3 2.94
51 3.06 465/500
350/375
Performance Curves
Performance Curves
RPCC RPEC RPGC RPIC RPKC
DSCH DSEH DSGH
Typical Pressure Rise DSIH
5000 5000 Typical
5000 Pressure Drop 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
30 30 30 30
P = psi
P = psi
P = bar
P = bar
P = bar
2000 2000 2000 2000 20 2000
18 18 18
1000 1000 1000 1000 15 1000
12 12 12
10
20 0 10 20 0 40 80 120 160 200 0 80 160 240 320 400
0 5 10 6 15 25 6 30 40 50 0 20 40 60
6 80 100
Flow = GPM Flow = GPM Flow = GPM 5
Flow = GPM Flow = GPM
0 20 40 60 80 0 40 80 120 160 0 70 140 210 280 0 100 200 300 400 500
■
Q Maximum
= L/min. operating pressure
Q = L/min.= 5000 psi Q = L/min. Q = L/min.
■ Will accept maximum pressure at Port 2.
■
■ Maximum operating
Back pressure on thepressure
tank port=(port
350 bar
2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Pilot flow
Factory = DSCH,
pressure DSEH:
settings 0,38 L/min.,
established at 4 DSGH,
GPM DSIH: 0,75 L/min. (Port 2 and 4 to Port 3).
■
■ Typical response time 10 ms.
Note: Low shift values can potentially result in charge pump pressure alone inadvertently shifting
■ the valve. Use
Maximum care =
leakage when
RPCC,selecting
RPEC:shift
2 inpressure.
3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ in3/min./1000
Pressures psi, RPKC:
on Ports in3/min./1000
2 and 4 5must psi. reversed shift can take place.
equalize before
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
DS ✱HC –
– X
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Shifting Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Non-adjustable G 10,0 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 120 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 H
C 14,0
150 -bar
6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
G 240 L/min.
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 4
2 1
b c
b c
Locating
Shoulder
Locating 3 Cartridge Dimensions
Shoulder Typical c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4”
Cartridge2.11 2.17
Dimensions 2.31 25/30
4
2 TypicalT - 10A 2.25Installation
Port
Outlet
Nominal RPEC – LAN
25 GPM
Cartridge Cavity
1.56 7/8”
a
2.00
b
2.06
c Torque
30/35
a Capacity RPGC – LAN
50 GPM T - 3A
Model Code 1.88 1 1/8” 2.12 2.18 2.38 (Nm)45/50
3
Port 60 L/min. RPIC –DSCS
100 GPM LAN – XCN
T - 16A T - 31A
2.44 1 84,8
1/4” 22,2
2.44 37
2.47 2.69 40/50
150/160
Inlet 1
2
200 120
GPM L/min.RPKC –DSES
LAN – XCN
T - 18A T - 32A
3.13 1 92,2
5/8” 2.81
28,6 2.94
42 3.06 350/375
60/70
Port
Performance Curves 240 L/min. DSGS – XCN T - 33A 114,4 31,8 72 200/215
DSIS – XCN
RPCC Port 1 Not Used RPEC 480 L/min. RPGC T - 34A
RPIC139,7 41,3 107
RPKC 465/500
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
Flow = GPM
10 10 10 10
■ Maximum operating pressure = 5000 psi
5 5 5 5
■ Will accept maximum pressure at Port 2.
0 15 ■ 32 45 60 0 40 80 110 0 80 160 220 0 160 320 360
Back
Q = L/min. pressure on the tank port
Q = L/min. (port 2) is directly additive
Q = L/min. at a 1:1 ratio to the valve setting.
Q = L/min.
■ Factory pressure settings established at 4 GPM
■
■ Typical response
Maximum operatingtimepressure
10 ms. = 350 bar
■ Maximum valve
leakage = RPCC, RPEC: 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
2 incc/min.
■ leakage = DSCS: 32,8 at 70 bar, DSES: 49,2 cc/min. at 70 bar, DSGS:
in3/min./1000
65,5 cc/min. atpsi, RPKC:
70 bar, 3/min./1000 psi.
5 in81,9
DSIS: cc/min. at 70 bar
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
DS ✱SC –
– ✱ ✱✱
X ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Shifting Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Non-adjustable C 2,0 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 120 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 E
C 5,0
150bar
- 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
G 240 L/min. F 7,0 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 480 L/min. G 10,0 bar
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 4 2 1
b c
b
c
Locating
Shoulder
Cartridge Dimensions
Locating 3 Typical c Installation
Shoulder Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
42 25 GPM RPEC – LAN T - 10A 1.56 Cartridge2.00
7/8” Dimensions
2.06 2.25 30/35
Outlet
Port Typical Installation
Nominal RPGC – LAN
50 GPM CartridgeT - 3A 1.88
Cavity 1 1/8”
a 2.12
b 2.18
c 2.38 Torque45/50
a Capacity
3 100 GPM Model Code
RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 (Nm)150/160
Port Inlet 1 60 L/min. DSCO – XCN T - 31A 84,8 22,2 37 40/50
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
2 120 L/min. DSEO – XCN T - 32A 92,2 28,6 42 60/70
Performance Curves
Port 240 L/min. DSGO – XCN T - 33A 114,4 31,8 72 200/215
RPCC RPEC 480 L/min. RPGC
DSIO – XCN T - 34A RPIC
139,7 41,3 RPKC
107 465/500
Port 1 Not Used
Typical Pressure Rise
Performance
5000 Curves 5000 5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
0 5 10
20 15 20 25 0 10 20 20 30 40 50 0 20 40 60
20 80 100 0 40 80 120 20 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
15 15 15 15
P = bar
P = bar
P = bar
P = bar
10
■ Maximum operating
10 pressure = 5000 psi 10 10
5
■ Will accept maximum
5 pressure at Port 2. 5 5
0 15
■
32
Back
45
pressure
60
on0
the tank
40
port
80
(port
110
2) is directly
0
additive
80 160
at a 1:1
220
ratio to
0
the 160
valve setting.
320 360
Q =■L/min.Factory pressure settings
Q = L/min.
established at 4 GPM Q = L/min. Q = L/min.
■ Typical response time 10 ms.
■
■ Maximum
Maximum operating
leakage = pressure
RPCC, RPEC: = 350 bar
2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ 3
in /min./1000
Minimum pilotpsi, 5 in3/min./1000
RPKC:required
pressure psi. = C Range: 2 bar, E Range: 5 bar
to shift valve
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ O
DS C – X
✱ ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Shifting Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Non-adjustable C 2,0 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 120 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 E
C 5,0
150bar
- 6000 psi +$ 2.00 V Viton
I
G GPM $ 97.30
100 L/min.
240 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
3
Check, Pilot-to-Close 147
3
Accumulator Sense, Pump Unload Valve
149
1 with Check - Pilot Capacity
4 2
2
Direct Acting, 2-way Directional Valve with Drain to
150
4 1 Port 4 - Normally Closed
3
2
Direct Acting, 2-way Directional Valve with Drain to
151
4 1 Port 4 - Normally Open
3
4 2
1
Vent-to-shift 2-position Diverter Valve - Normally Closed 152
4 2
1
Vent-to-shift, 2-position, 3-way Diverter Valve 153
4
2
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
P = bar
4 3000 4
3000 6 3000 6 3000 3000
3 3
2000 4 2000 4 2000 2000 2000
2 2
1000 1000 1000 1000 1000
2 2 1 1
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM
0 10 20 30 40 50 60 70 80 90 100 0 10
Flow = GPM Flow
20 30 40 50 60 70 80 90 100 = GPM
0 10 Flow
20 30 40 50 60 70 80 90 100 = GPM
0 10 20 30 40 50 60 70 80 90 100
Flow = GPM
Percentage of Setting Percentage of Setting Percentage of Setting Percentage of Setting
■ Maximum operating pressure = 5000 psi
■
■ Maximum
Will acceptoperating
maximum pressure
pressure= at
350 bar2.
Port
■
■ Back pressure on the tank port
Maximum valve leakage = FQCA: 32,8 (port 2) iscc/min.
directlyatadditive at a 1:1 49,2
70 bar, FQEA: ratiocc/min.
to the valve
at 70setting.
bar, FQGA:
■ 65,5 cc/min.
Factory at 70settings
pressure bar, FQIA: 81,9 cc/min.
established at 70 bar.
at 4 GPM
■
■ Valve
Typicalcloses whentime
response flow10from
ms. port 1 to port 2 exceeds the setting of the valve. Valve resets when
■ pressures
Maximumatleakage
port 1 and port 2 RPEC:
= RPCC, are equal.
2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ in3/min./1000
Flow psi, RPKC:
setting should 5 in325%
be at least /min./1000 psi.
above maximum normal system flow.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ A
FQ C – X
✱ A
✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control** Flow Rate Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 2-23 L/min. X Non-adjustable A N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 4-60 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
I
G L/min. $ 97.30
100 GPM
4-95 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 4-200 L/min. Customer must specify flow.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b 2 1
cc
Locating
1
b Shoulder
Locating
Shoulder
a Cartridge
Cartridge Dimensions
Dimensions
2 Typical Typical c Installation
Installation
Capacity
Capacity Cartridge Cartridge Cavity Cavitya ab Torque
Tank Model Code Lb Cc K Torque
Model Code (Nm)(lb. ft.)
a 12 RPCC –NQEBLAN – XAN
Pump 1 15GPM
- 200 L/min. T - 162A T - 3A
1.22 3/4”
47,8 2.11
28,6 2.17
18 2.31 60/7025/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance
Performance Curves
Curves
RPCC RPEC RPGC NQEB RPIC RPKC
Typical Pressure Rise
Approximate Closing Time
5000 5000 Typical Pressure
5000Drop after Air has been
5000 Purged 5000
4000 4000 4000 4000
P = psi
4000 35 12
P = psi
P = psi
P = psi
P = psi
P = bar
25
2000 2000 2000 8 2000 2000
20
1000 1000 15 1000 1000 1000
10 4
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
5
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
0 50 100 150 200 0 50 100 150 200
■ Maximum operating Qpressure
= L/min. = 5000 psi Q = L/min.
■ Will accept maximum pressure at Port 2.
■
■ Maximum operating
Back pressure on the pressure
tank port=(port
350 bar
2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure
Air-bleed settings
and start-up established
valves require at 4 GPM of 15 L/min. flow rate and 5,5 bar system pressure.
a minimum
■
■ Typical
The response
valve time 10
will re-open ms.system pressure falls below 1,7 bar.
when
■ Maximum leakage = RPCC, RPEC: 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
2 invary
■ After air has been purged, closing times
3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
from approximately 12 seconds at 15 L/min. to 0.5
in
seconds at 200 L/min.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP E
NQ ✱BC –
– ✱ ✱✱
X A ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Flow Rate Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E 15-200 L/min. X Non-adjustable A N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2
2 1
c
b
b
3
Locating
Shoulder
c Cartridge Dimensions
Typical c Installation
3 1
Capacity Cartridge Cavity a b Torque
Pilot Model Code L C K (lb. ft.)
Locating
a
Shoulder 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 Cartridge Dimensions
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet a Orifice Typical Installation
2
Diameter RPGC – LAN
50 GPM T - 3A
Cartridge 1.88
Cavity 1 1/8”
a 2.12
b 2.18c 2.38 Torque 45/50
Outlet Model Code (Nm)
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 1,27 mm COFO – XDN T - 2A 35,1 28,6 35,1 60/70
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
1 Inlet
Performance Curves
RPCC RPEC RPGC RPIC RPKC
Typical Pressure Rise
Performance
5000 Curves 5000 5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
40
■ Maximum operating pressure = 5000 psi
20
■ Will accept maximum pressure at Port 2.
■ Back pressure on the tank port0,0(port 5,0
2) is directly11,4
additive at a 1:1 ratio to the valve setting.
■ Factory pressure settings established Qat= 4 L/min.
GPM
■ Typical response time 10 ms.
■ Maximum operating pressure = 350 bar
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Pilot
in ratio = 120:1
3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■
■ Leakage
RPCC rate when
minimum closed
setting for= all
0,3spring
cc/min.ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
CO F C
O – ✱
X ✱
D✱N
Nominal
Orifice
Capacity Control** Adjustment Range Seal
Control** Minimum Pressure Seal
Diameter
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
F 1,27 mm X Standard Pilot D 3,5 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2
2 1
3
b c
b
c
Locating
Shoulder
3 1 Cartridge Dimensions
Port Locating Typical c Installation
Shoulder Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 Cartridge2.11
3/4” Dimensions
2.17 2.31 25/30
2 Typical Installation
a Capacity RPEC – LAN
25 GPM CartridgeT - 10A 1.56
Cavity 7/8”
a 2.00
b 2.06
c 2.25 Torque30/35
Outlet
2 50 GPM Model Code
RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 (Nm)45/50
Port 40 L/min.
100 GPM COBA – XCN
RPIC – LAN T - 16A
T - 163A
2.44
31
1 1/4”
19,1
2.44 2.47
32 2.69
35/40
150/160
Inlet 1 80 L/min. RPKC –CODA
200 GPM LAN – XCN
T - 18A T - 11A
3.13 134,9
5/8” 22,2
2.81 31
2.94 3.06 40/50
350/375
Port 1
160 L/min. COFA – XCN T - 2A 34,9 28,6 35 60/70
Performance Curves
320 L/min. COHA – XCN T - 17A 46 31,8 46 200/245
RPCC RPEC RPGC RPIC RPKC
640 L/min. COJA – XCN T - 19A 63,5 41,3 59 465/500
Performance Curves Typical Pressure Rise
5000 5000
COBA CODA COFA COHA COJA
5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
P = bar
P = bar
P = bar
P = bar
P = bar
Flow = GPM XEN Flow = GPM XEN Flow = GPM XEN Flow = GPM XEN Flow = GPM
6 XEN 6 6 6 6
3 XCN
■ Maximum
3 operating pressure3 = 5000 psi
XCN 3 XCN 3 XCN XCN
XAN XAN XAN XAN
XAN
0 10 20 30
■
40
Will0 accept
20
maximum
40 60
pressure
80 0
at Port
30
2.
60 90 120 0 80 160 240 320 0 160 320 480 640
Q = L/min. ■ Back pressure on the tank port (portQ2)= L/min.
Q = L/min. is directly additive at aQ1:1 ratio to the valve setting.
= L/min. Q = L/min.
■ Factory pressure settings established at 4 GPM
■
■ Maximum operating
Typical response timepressure
10 ms. = 350 bar
■
■ Pilot
Maximum 1.8:1 = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
ratio =leakage
■ in3/min./1000
Leakage rate whenpsi, RPKC:
closed 5= in
3/min./1000 psi.
0,07 cc/min.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
CO ✱AC –
– ✱
✱ ✱
✱✱✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Cracking Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B 40 L/min. X Standard Pilot A* 0,3 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
D
G 80
50 L/min.
GPM $ 51.80 K Handknob +$ 5.00 B*
C 1,0
150bar
- 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
F 160 L/min. C 2,0 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
H 320 L/min. D 3,5 bar
W 150 - 4500 psi +$ 0.00
J 640 L/min. E 5,0 bar
Adjustment Range Options:
F 7,0C,bar
A, B, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
* COBA and COFA are not
6 US Shortcut Catalogue #999-901-243
** See page 162 for information available in A and B
on Control Options Cracking Pressures.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c
Circuit
b Savers
ACCUMULATOR Locating SENSE, PUMP UNLOAD VALVE - PILOT CAPACITY
Shoulder
Cartridge Dimensions
Typical c Installation
Capacity 2 Cartridge Cavity a b Torque
Full Adjustment 5 Turns Model Code L C K (lb. ft.)
+ - a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 1
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
c 200 GPM 3RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
b
Performance Curves
RPCC RPEC RPGC RPIC
Cartridge Dimensions
RPKC
3 Typical
Typical Pressure Rise c Installation
Locating Capacity Cartridge Cavity a b Torque
Port
5000 Shoulder 5000 5000
Model Code 5000 L C
5000
(Nm)
4000 4000 4000 4000
P = psi
4000
P = psi
QPAA
3000 – LAN
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
QP ARP
✱ ✱ –C –✱✱✱ ✱
✱✱
Nominal
Capacity Control** Adjustment Range Seal
Nominal
Version Control** Adjustment Range Seal
Capacity C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 0,8 L/min. E 25 GPMA 15%
$ 36.20 L +$
Nominal C Tamper Resistant Standard
4.10Screw
B 50 - 1500 psi A 700.00
+$ - 210 bar
V Viton N Buna-N
+$ 2.00
Differential
G 50 GPM $ 51.80 K Handknob C +$ 5.00
Tamper C 150 - 6000 psi
Resistant +$
B 282.00
- 105 bar V Viton
B 20% Nominal
I $ 97.30
100 GPM Differential N 60 - 800 psi +$ 1.00
C 140 - 350 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
C 30% Nominal D 14 - 55 bar
Differential W 150 - 4500 psi +$ 0.00
D 50% Nominal
Differential Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
4000
P = psi
P = psi
P = psi
P = psi
■
■ Maximum operating pressure = 350 5000bar
psi
■
■ Will accept maximum
Check valve = 50 L/min. pressure at Port 2.
Free flow check cracking pressure = 0,3isbar
Back pressure on the tank port (port 2) directly additive at a 1:1 ratio to the valve setting.
■
■
■
■ Factory pressure settings established at 4 GPM
Pressure drop, port 1 to port 2 = 5 bar at 50 L/min.
■
■ Typicalapplying
When responsethis
time 10 ms. a separate drain line is required to prevent erratic operation caused
cartridge,
■ Maximum
by tank lineleakage
pressure RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
= fluctuations.
in3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Note: Careful consideration should be given when selecting an adjustment range. System pressure
■ RPCCand
drops minimum setting
flows tend for allthe
to affect spring rangesofisunloading
operation 75 psi valves.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
QC DRP
✱ ✱ –C –✱✱✱ ✱
✱ ✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Capacity Version Control** Adjustment Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 0,8 L/min. A 15% Nominal L Standard Screw A 70 - 210 bar N Buna-N
E $ 36.20
25 GPM Differential C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob C Tamper
+$ 5.00Resistant
C 150 - 6000 psi B
+$ 282.00
- 105 bar V Viton
B 20% Nominal
I $ 97.30
100 GPM Differential N 60 - 800 psi C
+$ 140
1.00
- 350 bar
K $187.00
C 30%
200 GPM Nominal Q 60 - 400 psi +$ 141.00
D - 55 bar
Differential
W 150 - 4500 psi +$ 0.00
D 50% Nominal
Differential
Adjustment Range Options:
A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
a 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
2
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Port
Performance Curves
Port 1
RPCC RPEC RPGC RPIC RPKC
Performance Curves
Typical Pressure Rise
5000 5000 5000 DRAX 5000 5000
4000 4000 4000 4000
P = psi
P = psi
P = psi
P = psi
10
P = bar
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP A
DR ✱XC –
– ✱ ✱N
L ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
C Capacity
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 2 L/min. L Standard Screw A 70 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 140
150 - 420
6000bar
psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
2 1
c 4 1
b
b Locating 3
c Shoulder
Cartridge Dimensions
Typical c Installation
4 Capacity Cartridge Cavity a b Torque
Model Code L
Cartridge DimensionsC K (lb. ft.)
Port a 12 GPM RPCC – LAN
Typical T - 162A 1.22 3/4” 2.11 2.17 2.31 Installation
25/30
23 Locating
Capacity
25 GPM RPEC –Model
LAN CodeT - 10A
Cartridge
1.56
Cavity a
7/8”
b
2.00 2.06
c
2.25
Torque
Port
Outlet Shoulder (Nm)30/35
50 GPM
2 L/min. RPGC – LAN
DRAY – LANT - 3A T - 21A1.88 1 1/8”
34,9 2.12
22,2 2.18
81 2.38 40/5045/50
a 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
2 Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Port
Performance Curves
Port 1
RPCC RPEC RPGC RPIC RPKC
Performance Curves
Typical Pressure Rise
5000 5000 5000 DRAY 5000 5000
4000 4000 4000 4000
Pressure Drop vs. Flow
P = psi
4000
P = psi
P = psi
P = psi
P = psi
10
P = bar
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP A
DR ✱YC –
– ✱ ✱N
L ✱ ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
A 2 L/min. L Standard Screw A 70 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C
C 140
150 - 420
6000bar
psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b 4 2
2 1
c
c
1
b Locating
Shoulder
Locating
Shoulder 3 Cartridge Dimensions
4 Typical c Installation
Port Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a RPCC – LAN Cartridge2.11
Dimensions2.17
a 12 GPM T - 162A 1.22 3/4” 2.31 25/30
2
3 Typical Installation
Port
Outlet Capacity RPEC – LAN
25 GPM Cartridge T - 10A Cavity1.56 a7/8” 2.00
b 2.06
c 2.25 Torque30/35
50 GPM RPGC –Model
LAN CodeT - 3A 1.88 1 1/8” 2.12 2.18 2.38 (Nm)45/50
10060 L/min. RPIC DSCX
GPM – LAN– XENT - 16AT - 31A2.44 84,8
1 1/4” 22,2
2.44 30.2
2.47 2.69 40/50
150/160
2 Inlet 1
200120
GPML/min. RPKCDSEX
– LAN– XENT - 18AT - 32A3.13 92,2
1 5/8” 28,6
2.81 33,3
2.94 3.06 60/70
350/375
Port
240 L/min. DSGX – XEN T - 33A 114,6 31,8 41,4 200/215
Performance Curves
480 L/min. DSIX – XEN T - 34A 139,7 41,3 53,8 465/500
RPCC 1 Port RPEC RPGC RPIC RPKC
Performance Curves Typical Pressure Rise
5000 5000 5000 5000
DSCX DSEX DSGX DSIX
5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
Flow 3 to 2
P = bar
P = bar
P = bar
3 to 2
Flow = GPM Flow = GPM
20 Flow
Fl
3 to 2 Flow = GPM
10 3 to 4
Flow = GPM
10
Flow = GPM
Flow
Fl
3 to 4 15 3 to 2
Fl
Flow XEN Fl
Flow
5
5 XEN■
Maximum operating 10 pressure = 5000 psi 5 XEN
3 to 4
XDN
XEN
XDN
3 to 4
0
■
20
Will 60
40
accept
80
maximum pressure
50 75
at Port
100 125
2. 0 50 150 200 250 0 100 200 300 400
■ Back pressure on the tank
Q = L/min. port (port 2) is directly Qadditive
Q = L/min. = L/min. at a 1:1 ratio to the Q =valve
L/min. setting.
■ Factory pressure settings established at 4 GPM
■
■ Maximum
Typical operating
response timepressure
10 ms. = 350 bar
■
■ Nominal vent flow = DSCX,
Maximum leakage = RPCC, RPEC: DSEX:20,38 L/min., DSGX,
in 3/min./1000 DSIX:30,60
psi, RPGC: L/min.
in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ There must be a pressure source at port 3, relative to port 1, to shift the valve.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱C
DS ✱ X –
– ✱
X ✱
E ✱
✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Minimum Control Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Non-adjustable C 2 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 120GPM
50 L/min. $ 51.80 K Handknob +$ 5.00 D 150
C 3,5 bar
- 6000 psi +$ 2.00 V Viton
IG 100 L/min. $ 97.30
240 GPM N
E 60 - 800 psi
5 bar +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 Customer may specify pressure setting. US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
b 4 2
2 1
c
c
1
b Locating
Shoulder
Locating
Shoulder 3
Cartridge Dimensions
4 Typical c Installation
Port Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a a 12 GPM RPCC – LAN T - 162A 1.22 Cartridge 2.11
3/4” Dimensions2.17 2.31 25/30
32 Typical Installation
Port
25 Capacity
GPM RPEC – Cartridge
LAN T - 10A Cavity 1.56 a7/8” 2.00
b 2.06
c 2.25 Torque30/35
Outlet
50 GPM RPGC –Model
LAN Code T - 3A 1.88 1 1/8” 2.12 2.18 2.38 (Nm)45/50
60 L/min.
100 GPM DSCY – XENT - 16AT - 31A2.44
RPIC – LAN
84,8
1 1/4”
22,2
2.44
30.2
2.47 2.69
40/50
150/160
2 Inlet 1
Port 200120
GPML/min. RPKCDSEY
– LAN– XENT - 18AT - 32A3.13 92,2
1 5/8” 28,6
2.81 33,3
2.94 3.06 60/70
350/375
240 L/min. DSGY – XEN T - 33A 114,6 31,8 41,4 200/215
Performance Curves
480 L/min. DSIY – XEN T - 34A 139,7 41,3 53,8 465/500
1 Port
RPCC RPEC RPGC RPIC RPKC
Performance Curves Typical Pressure Rise
5000 5000
DSCY DSEY DSGY DSIY
5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
Fl 0
Flow 0 40 80 120 160 200 0 3 to 80 160 240 320 400
P = bar
0 5 10 15 20 25 10 20 30 40 50 0 20 40 60 80 100
P = bar 2
P = bar
3 to 2 10 10
Flow = GPM Flow
Fl Flow = GPM
20 Fl
Flow
3 to 2 Flow = GPM Self-Piloted (1 Vented)
Flow = GPM Flow = GPM
3 to 4 15 3 to 2 3 to 4
Flow
Fl XEN XEN
5
5
XCN
■XDN Maximum operating 10
5
pressure = 5000 psi 5 XEN
3 to 4
XDN
XCN
XDN
XCN
Fl
Flow
3 to 4
0
■
20 Will 60accept
40 80 maximum0 25 pressure
50 75 at Port
100 125 2. 0 150 200 250 0 100 200 300 400
■ Q = L/min.
Back pressure on the tank port (port 2) is directly Qadditive
Q = L/min. = L/min. at a 1:1 ratio to the Q =valve
L/min. setting.
■ Factory pressure settings established at 4 GPM
■
■
Maximum operating
Typical response timepressure
10 ms. = 350 bar
■
■ Nominal
Maximum leakage = RPCC, DSEY:
vent flow = DSCY, RPEC: 0,38 L/min., DSGY,
2 in 3/min./1000 DSIY: 0,60
psi, RPGC: 3 in3L/min.
/min./1000 psi, RPIC: 4
■ 3
There must be psi,
in /min./1000 a pressure
RPKC:source 3 at port 3, relative
5 in /min./1000 psi. to port 1, to shift the valve.
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ Y
DS C – ✱
X ✱
E ✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Minimum Control Pressure Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 60 L/min. X Non-adjustable C 2 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
E
G 120 L/min. $ 51.80
50 GPM K Handknob +$ 5.00 D
C 3,5
150bar
- 6000 psi +$ 2.00 V Viton
I
G GPM $ 97.30
100 L/min.
240 N 5
E 60bar
- 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 480 L/min.
W 150 - 4500 psi +$ 0.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 Customer may specify pressure setting. US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Performance Curves 60 L/min. LHDT – XFN T - 31A 84,8 22,2 30.2 40/50
2 LHFT – XFN
RPCC
Port RPEC 120 L/min. RPGC T - 32A RPIC
92,2 28,6 RPKC
33,3 60/70
240 L/min. LHHT – XFN T - 33A 114,3 31,8 41,3 200/215
Typical Pressure Rise
5000 5000
5000 1 Port 5000 5000
4000 4000 4000 4000
P = psi
4000 P = psi
P = psi
P = psi
P = psi
3000
Performance
3000
Curves 3000 3000
2000
3000
2000
2000 2000 2000
Flow = L/min.
Flow = L/min.
75 150
■ 50Will accept maximum pressure at Port 2.
50 100
25Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
25 50
■ Factory pressure settings established at 4 GPM
0 100 150 200 250 300 0 100 150 200 250 300 0 100 150 200 250 300
■ Typical Presponse
= bar
time 10 ms. P = bar P = bar
■ Maximum leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ Maximum operating pressure = 350 bar
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱C
LH ✱ T –
– ✱
X ✱
F ✱
✱
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Capacity Control Nominal Control Pressure Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 60 L/min. X Non-adjustable D 3,5 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
F
G L/min. $ 51.80
120GPM
50 K Handknob +$ 5.00 E 150
C 5 bar- 6000 psi +$ 2.00 V Viton
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
H 240 L/min. F 7 bar
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
1
Relief Valves
PILOT OPERATED, BALANCED
3 PISTON
Full Adjustment 5 Turns
b + -
c 2
2 1
c Cartridge Dimensions
3
Port Typical c Installation
b Locating
Shoulder
Capacity Cartridge Cavity a b
L C K
Torque
Model Code (Nm)
Locating 40 L/min. HRDA – LAN T - 11A 35,0 22,2 78,9 80,2 85,0 45/50
Shoulder
a Cartridge Dimensions
2
Port Typical c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
1 Port
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Performance Curves 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN HRDA
T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC
Flow from Port – LAN
2 to Port 3 T - 18A 3.13from 1 5/8”
Flow 2.81 2.94 3.06 350/375
with Port 1 Blocked Port 2 to Port 1
Performance Curves 300 20
P = bar
200 14
100 7
Typical
MimimumPressure Rise
Setting
5000 5000 0 20 40 60
5000 0 20 405000 60 5000
4000 Q = L/min. 4000 Q = L/min.4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
HR DCA – ✱
L ✱
A✱N
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 40 L/min. L Standard Screw A 35 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
Adjustment B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Tamper Resistant +$ 5.00
C Handknob C
W 150
55 - -315
6000
barpsi +$ 2.00 V Viton
I 100 GPM $ 97.30 Factory Set N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 K Handknob Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6
156 US
UK Shortcut
Shortcut Catalogue #999-901-243
#999-901-244
Hybrid Valves
DIRECT ACTING RELIEF VALVE - AFTER CHECK
1
Relief Valves
PILOT OPERATED, BALANCED
3 PISTON
Full c
b Adjustment 5 Turns
+ - 2
2 1 Cartridge Dimensions
3
Port c Typical c Installation
Locating Capacity Cartridge Cavity a b Torque
b Shoulder
Model Code L C K (Nm)
40 L/min. HRDB – LAN T - 11A 35,0 22,2 78,9 80,2 85,0 45/50
Locating
a Shoulder
2 Cartridge Dimensions
Port
Typical c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
1 Port a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Performance
Outlet Curves
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN HRDB
T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
Flow from
200 GPM Port–2 LAN
RPKC to Port 3 T - 18A Flow
3.13 from 1 5/8” 2.81 2.94 3.06 350/375
with Port 1 Blocked Port 2 to Port 1
Performance Curves 300 20
P = bar
P = bar
100 7
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱
HR DCB – ✱
L ✱
A✱N
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C
D 12
40 GPM*
L/min. $ 31.90 L
L Standard Screw +$ 0.00
Standard Screw A
A 100
35 - -210
3000
barpsi +$ 0.00 N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
Adjustment B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 C Handknob
K Tamper Resistant +$ 5.00 W 150
C 55 - -315 barpsi
6000 +$ 2.00 V Viton
Factory Set
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 K Handknob Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
UK Shortcut Catalogue #999-901-244 157
6 US Shortcut Catalogue #999-901-243
Hybrid Valves
VENTABLE, PILOT OPERATED, BALANCED PISTON,
RELIEF VALVE - BEFORE CHECK
Relief Valves
b
PILOT OPERATED,
c
BALANCED
2 4 PISTON
Full
4 Adjustment 5 Turns
Port + -
Cartridge Dimensions
3 Typical c Installation
Port Locating 2 Capacity 1
Cartridge Cavity a b
L C K
Torque
Shoulder Model Code (Nm)
c
a
40 L/min. HVCA – LAN T - 21A 35,0 22,2 78,9 80,2 85,0 45/50
b
2
Port Locating
Shoulder
Cartridge Dimensions
1 Port Typical c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
Performance Curves
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 HVCA
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet Flow from Port 2 to Port 3 Flow from
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
with Port 1 Blocked Port 2 to Port 1
100 GPM
300 RPIC – LAN T - 16A 20 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
RPKC – LAN
P = bar
P = bar
200 GPM
200 T - 18A 14 3.13 1 5/8” 2.81 2.94 3.06 350/375
7
Performance Curves 100
Mimimum
Setting
RPCC RPEC 0 20 40 RPGC
60 0 20 RPIC
40 60 RPKC
Q = L/min. Q = L/min.
Typical Pressure Rise
5000 5000 5000 5000 5000
■ Maximum
4000 operating pressure = 350 bar
4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP CC
HV ✱ A – ✱
L ✱
A✱N
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control** Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 40 L/min. L Standard Screw A 5 - 210 bar N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
Adjustment B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 B 150
C 5 - 105 bar psi
- 6000 +$ 2.00 V Viton
C Tamper Resistant
I 100 GPM $ 97.30 Factory Set N
D 60
5 - -55
800
barpsi +$ 1.00
K 200 GPM $187.00 K Handknob Q
W 60
5 - -315
400bar
psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Hybrid Valves
VENTABLE, PILOT OPERATED, BALANCED PISTON, RELIEF VALVE - BEFORE
CHECK WITH INTEGRAL PILOT CONTROL CAVITY
1 The -8 control option allows the pilot control valve to be incorporated directly
b into the end of the relief cartridge via the T-8A cavity. These pilot control
Relief Valves 3 cartridges are sold separately and include electro-proportional, solenoid, air
pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
PILOT OPERATED, BALANCED PISTON
4
c T-8A
Full Adjustment 5 Turns
Port
+ - 2 4
3
Port Locating
Shoulder 2 1 Cartridge Dimensions
Typical Installation
c Capacity Cartridge Cavity a b c Torque
Model Code (Nm)
b a
2
40 L/min. HVCA – 8DN T - 21A 35,0 22,2 45,2 45/50
Port Locating
Shoulder
Cartridge Dimensions
Typical c Installation
1 Port Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Performance
2 Curves 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN HVCA-8
T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC
Flow from Port–2 LAN
to Port 3 T - 16A Flow from
2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM withRPKC
Port 1 Blocked
– LAN T - 18A Port
3.132 to Port 1
1 5/8” 2.81 2.94 3.06 350/375
300 20
Performance Curves
P = bar
P = bar
200 14
5000
Q = L/min. 5000
Q = L/min.
5000 5000
5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
0 5 10 15 20
■
25
Maximum 0 10
valve
20 30
leakage
40 50
(port 20 to20port40 3) 60= 32,8 cc/min.0at 70
80 100 40
bar
80 120 160 200 0 80 160 240 320 400
Flow = GPM
Flow = GPM ■ Free flow Flow check cracking pressure =Flow
= GPM 1,7=bar GPM Flow = GPM
■
■ Maximum
Minimum setting operating is 5pressure
bar for all= 5000 psiranges.
spring
■
■ Will
Backacceptpressuremaximum
at port 4pressure
(tank) isatdirectly
Port 2. additive to the valve setting at a 1:1 ratio.
■
■ Back
The check pressure on the
portion of tank port (port
the valve has a 2) is directly
maximum additive
leakage at of
rate a 1:1
lessratio
thanto0,07
the cc/min.
valve setting.
■
■ Factory pressure settings established at 4 GPM
Note: This valve deviates from Sun's normal flow path for four port relief valves; port 2 is the inlet,
■ Typical
port 1 isresponse
the system, timeport
10 3ms.is tank and port 4 is vent. Therefore, it is probably not useable in existing
■ standard Sun
Maximum relief =manifolds.
leakage RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
■ With the -8 control option, the main stage valve should first be installed to the correct torque value. The
■ T-8A pilot
RPCC controlsetting
minimum valve forshould then beranges
all spring installed
is 75into
psithe main stage valve to its required torque value.
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP CC
HV ✱ A –
– ✱
8 ✱
D✱N
Nominal
Nominal
Capacity Control** Adjustment Range Seal
Control Adjustment Range Seal
Capacity
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
C 40 L/min. 8 with T-8A cavity D 5 bar N Buna-N
E 25 GPM $ 36.20 C Tamper for +$ 4.10
Resistant
in hex body B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 pilot operation
K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
(see pilot control
I 100 GPM $ 97.30 section for alternate N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 options) Q 60 - 400 psi +$ 1.00
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut Catalogue #999-901-243
Hybrid Valves
NOTES
Page
Special Purpose Controls (for use in systems where adjustment is seldom changed after installation)
J Socket Head Set Screw with Cap 4,0 mm Hex F Wrench Adjustment
Stem seal - Seal under locknut.
Adjustment screw not retained. No Stem seal - Seal under locknut.
overset protection. Adjusting screw is not retained.
Overset protection-pilot spring cannot
go solid.
14,3 mm Hex
All Sun counterbalance cartridges are built with a leakproof adjustment - O-ring seals are on the adjusting screw-but are not designed for frequent
adjustment in the field. Cartridges that are factory pre-set by Sun to a customer specified pressure setting are available and can be installed directly
on a machine without the need for further adjustment.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Lock
1. Remove original wire stop ring
Assembly
Adapter
Locknut and locknut.
2. Thread on the adapter locknut
Key Lock Kit For all Sun cartridges with L and install new wire stop ring
993-008
adjustment (except Series 0 and through slot provided.
counterbalance cartridges). 3. Adjust valve to desired setting
and tighten adapter locknut.
Key Wire Stop Ring 4. Slide lock assembly over
adapter, lock and remove key.
Install while cartridge is screwed in 1. Do not remove stop ring.
cavity to prevent damage. 2. Install lock knob by snapping
onto the locknut.
3. Install star knob until contact is
5 made with the stop ring.
6 4. Caution during installation on
1
flow control valves (that have
1 no stop ring). Make sure valve
Maximum can be shut with hand knob
.750
higher than installed.
L adjustment 5. Insert pins in cover so that they
Three-winged For all Series 1, 2, 3, 4 project on backside.
Handknob Kit valves with L or O 6. Put cover on with inserted pins
991-034 adjustment except and drive pins in until flush
counterbalance cartridges. with cover.
When knob is used as a maximum
2.43diameter Setting Limiter:
62 mm
1. Set valve at desired maximum
.90 setting.
23 mm 2. Tighten lock nut
The handknob can be used
as a Maximum Setting Limiter. (110 lbs. inch).
3. Remove stop ring.
4. Install lock knob.
5. Install handknob until flush
with the lock knob.
2.43diameter
Three-winged 62 mm
Handknob Kit This kit should be used in .90
with 23 mm Follow installation instructions
1 3/8” dia. applications where there is high
vibration and a plastic lock knob described above.
aluminum lock
knob. may loosen.
991-039 Aluminum
Lock Knob
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Panel O controls
All Series 2 cartridges
Handknob Kit Handknob Lock Panel Nut
991-216 28,6 mm hex Assembly Knob
1”-14 thread
H H controls
Calibrated
All series of flow controls
Handknob Kit Only for cartridges originally
FDCB , NCEB, NCEC , supplied with an H handknob.
991-219 Valves can not be modified in the
NFDC, NFDD only
field.
FDEA , FDFA, NCFB, NCFC,
991-220
NCGB, NCGC, NFEC, Note: The H control is
NFED, NFFC, Exsisting Only available for the cartridges
NFFD only Handknob Lockring O-ring Cartridge shown to the left.
991-221 FDBA , NCCB , NCCC ,
NFCC, NFDC only
Adjustment
Screw Kit CKCA L**CKCD L** Manual
Release
991-112-003 Viton CKCB L**CPCA L** Screw
Back-up
Ring
CKCC L**
991-112-007 Buna-N
Only cartridges date stamped “62”
or earlier.
Adjustment
Screw Kit CKEA L**CKED L**
991-212-003 Viton CKEB L**CPEA L** Seal
CKEC L** Locknut
991-212-007 Buna-N
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Ports 1 to 2 Open
All Ports Blocked
Port 3 Blocked
Series Cavity Cavity Plug Cavity Plug
3 Model Code* Buna-N Viton Model Code Buna-N Viton 3
P T-9A XAOB-XX* XACBXX*
Ports 1 to 2 Open
All Ports Blocked
Port 3 and 4 Blocked
4 4
Series Cavity Cavity Plug Cavity Plug
Model Code* Buna-N Viton Model Code Buna-N Viton
3 3
1 T-21A XMOA-XX* XMCA-XX*
2 2 T-22A XNOA-XX* XNCA-XX* 2
3 T-23A XPOA-XX* XPCA-XX*
*Insert in the seventh position model code digit N to order Buna-N seals or V to order Viton seals.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
1 1
Cavity Adaptor (Converts Waterman 12-2 Cavity to the Sun T-8A Cavity)
*Insert in the seventh position model code digit N to order Buna-N seals or V to order Viton seals.
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
Connector Options for Sun Pilot Flow Solenoid Valves (DAAA, DBAA)
ISO / DIN 43650 SAE J858-A Twin Lead
Description Coil only part number Coil only part number Coil only part number
115 V AC
50/60 Hz 760-211 N/A N/A
230 V AC
50/60 Hz 760-223 N/A N/A
Connector Options for Sun Full Flow Solenoid Valves (DLDA, DTDA, DMDA, DNDA) and Proportional Valves (RBAP, PRDP, PRDL)
ISO/DIN 43650 Twin Spade AMP® Junior Timer Twin Lead Metri-Pack Deutsch
(SAE J858A)
Coil only part Coil only part Coil only part Coil only part Coil only part Coil only part
Description number number number number number number
115 V AC
50/60 Hz 770-211 N/A N/A N/A N/A N/A
230 V AC
50/60 Hz 770-223 N/A N/A N/A N/A N/A
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
No allowance has been made for viscosity effects, or regain of pressure downstream.
300
200
Pressure Drop bar
150
3mm
100
50
4mm
25
5mm
10
6mm
These charts are based on 5
7mm
the formula: 2 8mm
1
Q = a A 2AP 0 5 10 15 20 25 30 35 40
r
Where:
Flow L/min.
Q = Flow m3/sec.
a = orifice coefficient
A = orifice dia. cm 2
D P = pressure drop N/m2
r = density Ns2/m4
This equation becomes:
Q (l,min) = 0.4212 x d2 (mm) pressure drop (bar) Orifice diameter, milimetres
when c = 0.6
r = 0.9 g/cm3 2mm 3mm 4mm 5mm 6mm 7mm
350
300
8mm
200
Pressure Drop bar
150
100
10mm
50
12mm
25 14mm
16mm
10
5 20mm
2 24mm
1
Flow L/min.
Model Code Cavity Page Model Code Cavity Page Model Code Cavity Page
DBAA - ✱✱✱ T-9A 126 DOJP - ✱✱✱ T-24A 96 DVBM - 8✱✱ T-21A 107
DBAC - ✱✱✱ T-9A 119 DOJR - ✱✱✱ T-24A 94 DVBN - 8✱✱ T-21A 107
DBAC - ✱✱✱ T-9A 126 DOJR - 8✱✱ T-24A 95 DVBO - 8✱✱ T-21A 107
DBAH - ✱✱✱ T-9A 127 DOJS - ✱✱✱ T-24A 93 DVBP - 8✱✱ T-21A 107
DBAM - ✱✱✱ T-9 122 DPBA - ✱✱✱ T-11A 102 FCBB - ✱✱✱ T-162A 70
DBAP - ✱✱✱ T-9A 128 DPBB - ✱✱✱ T-11A 102 FCCB - ✱✱✱ T-13A 70
DCCC - ✱✱✱ T-61A 110 DPBC - ✱✱✱ T-11A 102 FCDB - ✱✱✱ T-5A 70
DCCD - ✱✱✱ T-61A 111 DPBD - ✱✱✱ T-11A 102 FCEB - ✱✱✱ T-16A 70
DCDC - ✱✱✱ T-62A 110 DPBM - ✱✱✱ T-21A 103 FCFB - ✱✱✱ T-18A 70
DCDD - ✱✱✱ T-62A 111 DPBN - ✱✱✱ T-21A 103 FDBA - ✱✱✱ T-13A 71
DCEC - ✱✱✱ T-63A 110 DPBO - ✱✱✱ T-21A 103 FDCB - ✱✱✱ T-5A 71
DCED - ✱✱✱ T-63A 111 DPBP - ✱✱✱ T-21A 103 FDEA - ✱✱✱ T-16A 71
DCFC - ✱✱✱ T-64A 110 DPCA - ✱✱✱ T-2A 102 FDFA - ✱✱✱ T-18A 71
DCFD - ✱✱✱ T-64A 111 DPCB - ✱✱✱ T-2A 102 FPCC - ✱✱✱ T-13A 73
DFCA - 8✱✱ T-13A 108 DPCC - ✱✱✱ T-2A 102 FPCH - ✱✱✱ T-13A 74
DFCB - 8✱✱ T-13A 109 DPCD - ✱✱✱ T-2A 102 FQCA - ✱✱✱ T-13A 144
DFDA - 8✱✱ T-5A 108 DPCM - ✱✱✱ T-22A 103 FQEA - ✱✱✱ T-5A 144
DFDB - 8✱✱ T-5A 109 DPCN - ✱✱✱ T-22A 103 FQGA - ✱✱✱ T-16A 144
DFEA - 8✱✱ T-16A 108 DPCO - ✱✱✱ T-22A 103 FQIA - ✱✱✱ T-18A 144
DFEB - 8✱✱ T-16A 109 DPCP - ✱✱✱ T-22A 103 FRBA - ✱✱✱ T-163A 76
DFFA - 8✱✱ T-18A 108 DRAX - ✱✱✱ T-21A 150 FRCA - ✱✱✱ T-11A 76
DKDP - ✱✱✱ T-21A 98 DRAY - ✱✱✱ T-21A 151 FRDA - ✱✱✱ T-2A 76
DKDR - ✱✱✱ T-21A 99 DRBA - ✱✱✱ T-11A 104 FREA - ✱✱✱ T-17A 76
DKDR - 8✱✱ T-21A 100 DRBB - ✱✱✱ T-11A 104 FRFA - ✱✱✱ T-19A 76
DKDS - ✱✱✱ T-21A 97 DRBC - ✱✱✱ T-11A 104 FSBA - ✱✱✱ T-31A 83
DKFP - ✱✱✱ T-22A 98 DRBD - ✱✱✱ T-11A 104 FSBD - ✱✱✱ T-31A 82
DKFR - ✱✱✱ T-22A 99 DRBR - ✱✱✱ T-21A 105 FSBS - ✱✱✱ T-31A 84
DKFR - 8✱✱ T-22A 100 DSCH - ✱✱✱ T-31A 140 FSCA - ✱✱✱ T-31A 83
DKFS - ✱✱✱ T-22A 97 DSCO - ✱✱✱ T-31A 142 FSCD - ✱✱✱ T-31A 82
DKHP - ✱✱✱ T-23A 98 DSCS - ✱✱✱ T-31A 141 FSCH - ✱✱✱ T-31A 85
DKHR - ✱✱✱ T-23A 99 DSCX - ✱✱✱ T-31A 152 FSCS - ✱✱✱ T-31A 84
DKHR - 8✱✱ T-23A 100 DSCY - ✱✱✱ T-31A 153 FSDA - ✱✱✱ T-32A 83
DKHS - ✱✱✱ T-23A 97 DSEH - ✱✱✱ T-32A 140 FSDD - ✱✱✱ T-32A 82
DKJP - ✱✱✱ T-24A 98 DSEO - ✱✱✱ T-32A 142 FSDH - ✱✱✱ T-32A 85
DKJR - ✱✱✱ T-24A 99 DSES - ✱✱✱ T-32A 141 FSDS - ✱✱✱ T-32A 84
DKJR - 8✱✱ T-24A 100 DSEX - ✱✱✱ T-32A 152 FSEA - ✱✱✱ T-33A 83
DKJS - ✱✱✱ T-24A 97 DSEY - ✱✱✱ T-32A 153 FSED - ✱✱✱ T-33A 82
DLDA - ✱✱✱ T-13A 114 DSGH - ✱✱✱ T-33A 140 FSEH - ✱✱✱ T-33A 85
DMDA - ✱✱✱ T-11A 116 DSGO - ✱✱✱ T-33A 142 FSES - ✱✱✱ T-33A 84
DNDA - ✱✱✱ T-31A 117 DSGS - ✱✱✱ T-33A 141 FSFA - ✱✱✱ T-34A 83
DODP - ✱✱✱ T-21A 96 DSGX - ✱✱✱ T-33A 152 FSFD - ✱✱✱ T-34A 82
DODR - ✱✱✱ T-21A 94 DSGY - ✱✱✱ T-33A 153 FSFH - ✱✱✱ T-34A 85
DODR - 8✱✱ T-21A 95 DSIH - ✱✱✱ T-34A 140 FSFS - ✱✱✱ T-34A 84
DODS - ✱✱✱ T-21A 93 DSIO - ✱✱✱ T-34A 142 FVCA - ✱✱✱ T-21A 77
DOFP - ✱✱✱ T-22A 96 DSIS - ✱✱✱ T-34A 141 FVCA - 8✱✱ T-21A 78
DOFR - ✱✱✱ T-22A 94 DSIX - ✱✱✱ T-34A 152 FVDA - ✱✱✱ T-22A 77
DOFR - 8✱✱ T-22A 95 DSIY - ✱✱✱ T-34A 153 FVDA - 8✱✱ T-22A 78
DOFS - ✱✱✱ T-22A 93 DTDA - ✱✱✱ T-13A 115 FVEA - ✱✱✱ T-23A 77
DOHP - ✱✱✱ T-23A 96 DVBA - 8✱✱ T-11A 106 FVEA - 8✱✱ T-23A 78
DOHR - ✱✱✱ T-23A 94 DVBB - 8✱✱ T-11A 106 FVFA - ✱✱✱ T-24A 77
DOHR - 8✱✱ T-23A 95 DVBC - 8✱✱ T-11A 106 FVFA - 8✱✱ T-24A 78
DOHS - ✱✱✱ T-23A 93 DVBD - 8✱✱ T-11A 106 FXBA - ✱✱✱ T-162A 69
Model Code Cavity Page Model Code Cavity Page Model Code Cavity Page
FXCA - ✱✱✱ T-13A 69 LPBC - ✱✱✱ T-163A 91 PPDB - 8✱✱ T-11A 38
FXDA - ✱✱✱ T-5A 69 LPDA - ✱✱✱ T-11A 91 PPFB - ✱✱✱ T-2A 31
FXEA - ✱✱✱ T-16A 69 LPDC - ✱✱✱ T-11A 91 PPFB - 8✱✱ T-2A 38
FXFA - ✱✱✱ T-18A 69 LPFA - ✱✱✱ T-2A 91 PPFC - ✱✱✱ T-2A 36
HRDA - ✱✱✱ T-11A 156 LPFC - ✱✱✱ T-2A 91 PPHB - ✱✱✱ T-17A 31
HRDB - ✱✱✱ T-11A 157 LPHA - ✱✱✱ T-17A 91 PPHB - 8✱✱ T-17A 38
HVCA - ✱✱✱ T-21A 158 LPHC - ✱✱✱ T-17A 91 PPHC - ✱✱✱ T-17A 36
HVCA - 8✱✱ T-21A 159 LPJA - ✱✱✱ T-19A 91 PPJB - ✱✱✱ T-19A 31
LHDA - ✱✱✱ T-31A 79 LPJC - ✱✱✱ T-19A 91 PPJB - 8✱✱ T-19A 38
LHDT - ✱✱✱ T-31A 154 LRBA - ✱✱✱ T-163A 92 PPJC - ✱✱✱ T-19A 36
LHFA - ✱✱✱ T-32A 79 LRBC - ✱✱✱ T-163A 92 PRDB - ✱✱✱ T-11A 32
LHFT - ✱✱✱ T-32A 154 LRDA - ✱✱✱ T-11A 92 PRDL - ✱✱✱ T-11A 40
LHHA - ✱✱✱ T-33A 79 LRDC - ✱✱✱ T-11A 92 PRDP - ✱✱✱ T-11A 41
LHHT - ✱✱✱ T-33A 154 LRFA - ✱✱✱ T-2A 92 PRFB - ✱✱✱ T-2A 32
LHJA - ✱✱✱ T-34A 79 LRFC - ✱✱✱ T-2A 92 PRHB - ✱✱✱ T-17A 32
LKDC - ✱✱✱ T-11A 90 LRHA - ✱✱✱ T-17A 92 PRJB - ✱✱✱ T-19A 32
LKFC - ✱✱✱ T-2A 90 LRHC - ✱✱✱ T-17A 92 PVDA - ✱✱✱ T-21A 33
LKHC - ✱✱✱ T-17A 90 LRJA - ✱✱✱ T-19A 92 PVDA - 8✱✱ T-21A 39
LKJC - ✱✱✱ T-19A 90 LRJC - ✱✱✱ T-19A 92 PVDB - ✱✱✱ T-21A 34
LODA - ✱✱✱ T-11A 88 NCBB - ✱✱✱ T-162A 68 PVFA - ✱✱✱ T-22A 33
LODA - 8✱✱ T-11A 89 NCCC - ✱✱✱ T-13A 68 PVFA - 8✱✱ T-22A 39
LODB - ✱✱✱ T-11A 88 NCEB - ✱✱✱ T-5A 68 PVFB - ✱✱✱ T-22A 34
LODB - 8✱✱ T-11A 89 NCCB - ✱✱✱ T-13A 68 PVHA - ✱✱✱ T-23A 33
LODC - 8✱✱ T-11A 88 NCEC - ✱✱✱ T-5A 68 PVHA - 8✱✱ T-23A 39
LODD - ✱✱✱ T-11A 88 NCFB - ✱✱✱ T-16A 68 PVHB - ✱✱✱ T-23A 34
LODD - 8✱✱ T-11A 89 NCFC - ✱✱✱ T-16A 68 PVJA - ✱✱✱ T-24A 33
LODO - ✱✱✱ T-11A 88 NCGB - ✱✱✱ T-18A 68 PVJA - 8✱✱ T-24A 39
LOFA - ✱✱✱ T-2A 88 NCGC - ✱✱✱ T-18A 68 PVJB - ✱✱✱ T-24A 34
LOFA - 8✱✱ T-2A 89 NFAB - ✱✱✱ T-8A 132 QCDA - ✱✱✱ T-21A 149
LOFB - ✱✱✱ T-2A 88 NFBC - ✱✱✱ T-162A 66 QCDB - ✱✱✱ T-21A 149
LOFB - 8✱✱ T-2A 89 NFCC - ✱✱✱ T-13A 66 QCDC - ✱✱✱ T-21A 149
LOFC - ✱✱✱ T-2A 88 NFCD - ✱✱✱ T-13A 67 QCDD - ✱✱✱ T-21A 149
LOFD - ✱✱✱ T-2A 88 NFDC - ✱✱✱ T-5A 66 QCDD - ✱✱✱ T-21A 149
LOFD - 8✱✱ T-2A 89 NFDD - ✱✱✱ T-5A 67 QPAA - ✱✱✱ T-11A 148
LOFO - ✱✱✱ T-2A 88 NFEC - ✱✱✱ T-16A 66 QPAB - ✱✱✱ T-11A 148
LOHA - ✱✱✱ T-17A 88 NFED - ✱✱✱ T-16A 67 QPAC - ✱✱✱ T-11A 148
LOHA - 8✱✱ T-17A 89 NFFC - ✱✱✱ T-18A 66 QPAD - ✱✱✱ T-11A 148
LOHB - ✱✱✱ T-17A 88 NFFD - ✱✱✱ T-18A 67 RBAA - ✱✱✱ T-3A 8
LOHB - 8✱✱ T-17A 89 NQEB - ✱✱✱ T-3A 145 RBAC - ✱✱✱ T-10A 8
LOHC - ✱✱✱ T-17A 88 PBBB - ✱✱✱ T-163A 30 RBAE - ✱✱✱ T-8A 130
LOHD - ✱✱✱ T-17A 88 PBDB - ✱✱✱ T-11A 30 RBAP - ✱✱✱ T-8A 13
LOHD - 8✱✱ T-17A 89 PBDB - 8✱✱ T-11A 37 RBAP - ✱✱✱ T-8A 133
LOHO - ✱✱✱ T-17A 88 PBFB - ✱✱✱ T-2A 30 RBAR - ✱✱✱ T-8A 131
LOJA - ✱✱✱ T-19A 88 PBFB - 8✱✱ T-2A 37 RDBA - ✱✱✱ T-162A 7
LOJA - 8✱✱ T-19A 89 PBFC - ✱✱✱ T-2A 35 RDDA - ✱✱✱ T-10A 7
LOJB - ✱✱✱ T-19A 88 PBHB - ✱✱✱ T-17A 30 RDFA - ✱✱✱ T-3A 7
LOJB - 8✱✱ T-19A 89 PBHB - 8✱✱ T-17A 37 RDHA - ✱✱✱ T-16A 7
LOJC - ✱✱✱ T-19A 88 PBHC - ✱✱✱ T-17A 35 RDJA - ✱✱✱ T-18A 7
LOJD - ✱✱✱ T-19A 88 PBJB - ✱✱✱ T-19A 30 RPCC - ✱✱✱ T-162A 6
LOJD - 8✱✱ T-19A 89 PBJB - 8✱✱ T-19A 37 RPCC - 8✱✱ T-162A 14
LOJO - ✱✱✱ T-19A 88 PBJC - ✱✱✱ T-19A 35 RPEC - ✱✱✱ T-10A 6
LPBA - ✱✱✱ T-163A 91 PPDB - ✱✱✱ T-11A 31 RPEC - 8✱✱ T-10A 14
Model Code Cavity Page Model Code Cavity Page Model Code Cavity Page
RPGC - ✱✱✱ T-3A 6 RSFC - 8✱✱ T-2A 23 RVGA - ✱✱✱ T-17A 16
RPGC - 8✱✱ T-3A 14 RSFE - ✱✱✱ T-2A 24 RVGB - ✱✱✱ T-17A 17
RPGD - ✱✱✱ T-3A 12 RSHC - ✱✱✱ T-17A 22 RVGD - ✱✱✱ T-23A 19
RPGS - ✱✱✱ T-3A 15 RSHC - 8✱✱ T-17A 23 RVGD - 8✱✱ T-23A 20
RPGT - ✱✱✱ T-3A 10 RSHE - ✱✱✱ T-17A 24 RVIA - ✱✱✱ T-19A 16
RPIC - ✱✱✱ T-16A 6 RSJC - ✱✱✱ T-19A 22 RVIB - ✱✱✱ T-19A 17
RPIC - 8✱✱ T-16A 14 RSJC - 8✱✱ T-19A 23 RVID - ✱✱✱ T-24A 19
RPID - ✱✱✱ T-16A 12 RSJE - ✱✱✱ T-19A 24 RVID - 8✱✱ T-24A 20
RPIS - 8✱✱ T-16A 15 RVBA - ✱✱✱ T-163A 16 SCCA - ✱✱✱ T-11A 26
RPKC - ✱✱✱ T-18A 6 RVBB - ✱✱✱ T-163A 17 SCEA - ✱✱✱ T-2A 26
RPKC - 8✱✱ T-18A 14 RVCA - ✱✱✱ T-11A 16 SCGA - ✱✱✱ T-17A 26
RPKD - ✱✱✱ T-18A 12 RVCB - ✱✱✱ T-11A 17 SCIA - ✱✱✱ T-19A 26
RQEB - ✱✱✱ T-10A 11 RVCD - ✱✱✱ T-21A 19 SQDB - ✱✱✱ T-11A 27
RQGB - ✱✱✱ T-3A 11 RVCD - 8✱✱ T-21A 20 SQFB - ✱✱✱ T-2A 27
RQIB - ✱✱✱ T-16A 11 RVEA - ✱✱✱ T-2A 16 SQHB - ✱✱✱ T-17A 27
RQKB - ✱✱✱ T-18A 11 RVEB - ✱✱✱ T-2A 17 SQJB - ✱✱✱ T-19A 27
RSBC - ✱✱✱ T-163A 22 RVED - ✱✱✱ T-22A 19 SXCA - ✱✱✱ T-11A 25
RSDC - ✱✱✱ T-11A 22 RVED - 8✱✱ T-22A 20 SXEA - ✱✱✱ T-2A 25
RSDC - 8✱✱ T-11A 23 RVES - ✱✱✱ T-2A 18
RSFC - ✱✱✱ T-2A 22 RVGS - ✱✱✱ T-17A 18
Caution
Sun Hydraulics Limited manufactures a variety of replacing any Sun cartridges, users should first check with the
cartridge valves that will fit into the same Sun cavity. Each manufacturer's service literature, their local Sun distributor, or
cartridge is marked with a seven-digit part identification code the Sun factory before making any part substitutions.
and a four-digit date code, stamped on the hex surfaces.
NOTE: To avoid serious injury, the manufacturer's service
Designers and users of Sun components are advised that
literature must be consulted before working on any
physical interchangeability of cartridges does not
hydraulic system.
necessarily mean functional interchangeability. When
Limited Warranty
Sun Hydraulics Limited warrants its products free from tampering, or abuse, or which have been repaired or altered
defects in material, workmanship, and design for a period of outside of the Sun Hydraulics factory. Sun’s Limited’s liability
three years after their installation, provided the installation date under this warranty shall extend only to repair or replacement,
is less than one year after manufacture. “O-rings” and seals f.o.b. Sun’s factory, of any defective part or product determined
are specifically exempted from this warranty. In no instance by inspection as not conforming to this warranty. Sun makes no
is there any warranty of fitness for a particular use and Sun other warranties, expressed or implied, and is not responsible
Hydraulics Limited cannot and does not accept responsibility of for any consequential damages resulting from use by any buyer
any type for any of its products that have been subjected to or user, Sun Hydraulics’ liability being limited to the value of
improper installation, improper application, negligence, product sold or obligation to replace a defective part.
Performance Assurance
All Sun cartridges valves are individually tested at the buyer's application is the responsibility of the buyer.
factory and preset to specific pressure or flow settings where This is typically accomplished by the manufacture of a
indicated in this catalogue. However, as the actual performance prototype followed by a test or qualification program on the part
of buyers' equipment cannot be reproduced in Sun's testing of the buyer.
laboratory, assurance of suitability of Sun products in the
Application Limitations
Worldwide Distributors
Telephone Facsimile
(Dial International Access Code (Dial International Access Code
Country Name before number listed below) before number listed below)
Country City Local Country City Local
Code Code Number Code Code Number
European Distributors
Telephone Facsimile
(Dial International Access Code (Dial International Access Code
Country Name before number listed below) before number listed below)
Country City Local Country City Local
Code Code Number Code Code Number