Professional Documents
Culture Documents
CH-4415 Lausen/Switzerland
01/2009
30 30
21
www.ronda-startech.com
60 60
12 12
Cal. 5130.D 9
20 6
3
10
45 15 9
20 6
3
10
45 15
Cal. 5130.B
30 30
1112 1 1112 1
10 2 21 10 2
9 3 9 3
8 4 8 4
7 6 5 7 6 5
Display elements Control buttons The alarm and chronograph are combined in Cal. 5130.D and 5130.B.
All functions can be operated with the 2 push-buttons and crown.
Minute hand
Hour and 20 6 10
30
Crown
1112 1
Minute counter 10 2 21 Chronograph active
9
8 4
3
Push-button B Push-button B is also operative for the chronograph as soon as timing is
Center stop-second 7 6 5
started with push-button A.
At the end of timing and when the chronograph hands are reset to the zero
Alarm and reference time positions the push-button functions once again assume their «initial status».
Second hand The alarm cannot be adjusted when the chronograph is active.
Date 5130.D
Date 5130.B Setting the date (quick mode) Hour counter Push-button A Chronograph: Basic function
31 21 (Start / Stop / Reset)
Pull out the crown to position II (the watch
30
60 30
12
continues to run). 12
60
Example:
45
20
9
6
3
10
15 9
20 6
3
10
45 15
Start: Press push-button A.
30 30
10
1112 1
2 31 I II Turn the crown until the correct 10
1112 1
2 21 Stop: to stop the timing, press
9 3
date 01 appears. 9 3
8
7 6 5
4 8
7 6 5
4 pushbutton A once more and read
the 3 chronograph counters:
Date 5130.D Push the crown back into position I. Minute counter 4h / 20 min / 38 sec
Please note:
01 21 Zero positioning:
The date of the following day must be set in
Press push-button B.
the calendar changing phase between 9 PM
(The 3 chronograph hands will be reset to
30 30
60 60
and midnight.
12 12
20
9 3
10
45 15 9
20
3
10
45 15 their zero positions).
6 6
1112 1
30
Setting the date too quickly in quick mode 1112 1
30
I II
10
9
2
3
01 can result in the incorrect date being 10
9
2
3
21
8 4 displayed. Switching the date between 8 4 Note
7 6 5
01 and 31 (position II) restores the syn-
7 6 5
The alarm cannot be used as long as the
chronisation. Push-button B chronograph is in operation.
9
12
3 45 15
to their zero positions. 9 3 45 15
20 20 10
Please note:
10 6
Please note:
65,5% =
= 40mm
40mm Druchmesser
6
30 30
1112 1
10
9
1112 1
2
3
21
timing can be continued by pressing
65,5%
* Following , the accumulation of the Druchmesser
65,5%
21
= 40mm *Druchmesser
Following , further intervals or inter-
10
9
2
3
8
7 6 5
4
push-button A
8
7 6 5
4
65,5%= 40mm Druchmesser
mediates can be displayed by pressing
push-button B (display interval / make up
(Restart / Stop, Restart / Stop, …) Push-button B measured time, ...)
Push-button B
21
hands to zero position 65,5% = 40mm
SingleDruchmesser
step A
Continuous A
1 x short
long III
30
60
Example: III
III
One or several chronograph hands are not
12
7 6 5 7 6 5
Turn the crown until yesterday’s date Push the crown back into position I
Alarm time Date 5130.D appears 03 . Reference time
(the display changes from reference to
Second hand alarm time.)
03 Pull out the crown to position III 04
(the second hand stops. The display
30
60 30
60
12
45
changes from alarm time to reference 12
45 15 Please note:
9 3 15 9 3
20 6 10 time.) 20 6 10
1112 1
30
1112 1
30
Resetting the time also requires the identical
03 I II III 04 I II III
10
9
2
3
10
9
2
3 correction of the reference time.
8 4 8 4 Please refer to «setting the reference time».
7 6 5 7 6 5
Reference time Alarm time * Please observe the AM / PM clock rhythm.
1112 1
30
1112 1
30
2 beeps alarm switched on
10 2 31 I mode is active. 10 2 31 I
9 3 9 3
8 4 8 4 1 beep alarm switched off
7 6 5
Setting 7 6 5
Short pressing (less than 1 second):
Alarm time Push-button the alarm time is moved forward by the Alarm time Push-button
minute.
Long pressing (longer than 2 seconds):
the alarm time is moved forward until the Please note:
push-button is released. The alarm can be set maximum 12 hours
before the desired alarm time.
Please note:
If the push-button is not activated for Once the set alarm time has been reached,
10 seconds, the setting mode of the alarm a signal is emitted for 20 seconds.
Note time deactivates itself. At the same time, This signal is repeated after two minutes.
The alarm cannot be used as long as two beeps are emitted to indicate that the Following brief pressing of the push-button,
the chronograph is in operation. alarm is switched on. the signal is immediately switched off.
Setting the reference time
* Push the crown back into position I
04 04 (the display changes from reference time
* Pull out the crown to position III
30
60 (second hand stops. The display changes 30
60 to alarm time).
12
9
12