Professional Documents
Culture Documents
GRP Catalogue PDF
GRP Catalogue PDF
Release. 3
Iniziative Industriali S.p.A. Date : 01.03.99
INTRODUCTION
This PRODUCT LIST contains the data of pressure classes (NP), stiffness (S), dimensions and weights (w) for
the standard filament wound polyester and vinylester pipes and hand lay-up fittings in the range of Nominal
Diameter from ND 25 to ND 1200 produced by INIZIATIVE INDUSTRIALI.
Products for size ranging from ND 1300 to ND 3000 and for higher pressures are available upon request.
Standard products are based on isophtalic polyester and vinylester resin matrix, 0.8 - 1.2 mm thick internal
liner and 0.2-0.3 mm thick external coating. On special request or depending on the fluid, other types of resins
and liners can be supplied.
The listed dimensions are the minimum for installation, assembly and packaging purpose. The production
tolerances are applicable for all dimensions. Weights indicated are nominal values.
For dimensions of factory pre-fabricated pipeline sections (spools), please contact INIZIATIVE INDUSTRIALI.
The joining system methods are the followings :
The PRODUCT LIST also provides in appendix A the dimensions and weight of pipes and flanges approved by
FMRC for Underground Fire Service. The other approved products (elbows, Tees, reducers, end caps) have
the same dimensions of the standard products rated pressure 16 bars in size (ND) of 4” (100 mm) through 20”
(500 mm) included in the PRODUCT LIST. The FMRC approved products have rated pressure 16 bars in size
(ND) of 4” (100 mm) through 20” (500 mm) as appear in the Automatic sprinkler section of the FMRC Approval
guide” suitable for unrestrained use permitted by Butt & Strap joint and/or Bell & Spigot Lock joint with double
O-ring.
The information contained in this catalogue was correct at the time of last release. INIZIATIVE INDUSTRIALI
reserve the right to change any products, dimensions or data described without advice.
This literature is intended to be used by specialized personnel in accordance with currently accepted industry
practice.
I
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
TABLE OF CONTENTS
II
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 1 Sheet 1 of 1
PLASTIWIND PIPE BELL/SPIGOT DOUBLE O-RING
ND L Lu NP = 10 bar NP = 16 bar
S=1250 S=2500 S=2500 S=5000 S=10000
t w t w t w t w t w
25 5950 5812 4.3 0.7 4.3 0.7 4.3 0.7 4.3 0.7 4.3 0.7
40 5950 5802 3.6 1.0 3.6 1.0 3.6 1.0 3.6 1.0 3.6 1.0
50 5950 5763 3.7 1.3 3.7 1.3 3.7 1.3 3.7 1.3 3.7 1.3
75 5950 5763 3.7 1.8 3.7 1.8 3.7 1.8 3.7 1.8 3.7 1.8
100 5950 5763 3.7 2.4 3.7 2.4 3.7 2.4 3.7 2.4 3.7 2.4
125 5950 5727 3.7 3.1 3.7 3.1 3.7 3.1 3.7 3.1 3.7 3.1
150 11950 11722 3.8 3.6 3.8 3.6 3.8 3.6 3.8 3.6 3.8 3.6
200 11950 11722 3.6 4.5 3.6 4.5 3.6 4.5 3.6 4.5 4.2 5.3
250 11950 11722 3.6 5.7 3.6 5.7 3.6 5.7 4.3 6.6 5.0 7.8
300 11950 11674 3.7 7.1 4.1 8.0 4.1 8.0 4.8 9.3 5.8 11.2
350 11950 11674 3.6 8.1 4.2 9.4 5.0 11.3 5.6 12.6 6.8 15.0
400 11950 11674 4.2 10.8 4.9 12.6 4.9 12.6 6.2 15.8 7.5 19.1
450 11950 11635 4.3 12.9 5.4 16.0 5.4 16.0 6.7 19.5 8.0 23.1
500 11950 11635 5.0 16.5 5.9 19.1 6.4 20.6 7.3 23.5 9.1 28.9
600 11950 11635 5.5 21.3 6.8 26.0 6.8 26.0 8.4 32.0 10.7 40.4
700 11950 11635 6.4 28.2 8.3 36.5 8.3 36.5 9.7 42.2 12.3 53.7
800 11950 11635 7.2 36.6 9.1 45.8 9.1 45.8 11.1 55.3 13.8 68.6
900 11950 11614 7.8 45.0 9.7 55.4 9.7 55.4 12.3 69.6 15.6 87.3
1000 11950 11604 9.0 57.0 10.9 68.0 11.4 71.2 13.5 83.3 17.0 104.8
1200 11950 11604 11.0 81.5 13.0 95.6 13.6 100.2 16.0 117.0 20.0 145.3
III
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 2 Sheet 1 of 1
PLASTIWIND PIPE BELL/SPIGOT DOUBLE O-RING LOCK JOINT
IV
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 3 Sheet 1 of 1
PLASTIWIND PIPE PLAIN ENDS
ND
Tab. N° 4 Sheet 1 of 1
V
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
VI
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 5 Sheet 1 of 1
PLASTISAND PIPE BELL/SPIGOT DOUBLE O-RING – GRAVITY PIPES
VII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 6 Sheet 1 of 1
PLASTISAND PIPE BELL/SPIGOT DOUBLE O-RING LOCK JOINT – PRESSURE PIPES
ND
Lu
VIII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 7 Sheet 1 of 1
PLASTISAND PIPE PLAIN ENDS – PRESSURE PIPES
ND
IX
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 8 Sheet 1 of 1
PLASTISAND PIPE LIPS GASKET – GRAVITY PIPES
DN
Lu
ND L Lu S=5000
t w
400 11950 11674 6.1 14.9
450 11950 11635 6.6 18.5
500 11950 11635 7.5 23.3
600 11950 11635 8.9 33.7
700 11950 11635 10.6 47.4
800 11950 11635 12.2 62.2
900 11950 11614 14.0 79.7
1000 11950 11604 15.9 102.3
1200 11950 11604 18.2 139.3
X
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 9 Sheet 1 of 1
ELBOW 90° plain ends
90°
L t
R=1.5ND
ND
NOTE: - Elbow not included in this table can be obtained by interpolation between tabulated values.
- The ends of the elbows will be tapered up to 50% of the thickness for a maximum length of 4 times the thickness.
- Dimensions in mm, Weight in kg.
XI
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 10 Sheet 1 of 1
ELBOW 60° plain ends
60°
t
L R=1.5ND
ND
NOTE: - Elbow not included in this table can be obtained by interpolation between tabulated values.
- The ends of the elbows will be tapered up to 50% of the thickness for a maximum length of 4 times the thickness.
- Dimensions in mm, Weight in kg.
Tab. N° 11 Sheet 1 of 1
XII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
45°
t
L R=1.5ND
ND
NOTE: - Elbow not included in this table can be obtained by interpolation between tabulated values.
- The ends of the elbows will be tapered up to 50% of the thickness for a maximum length of 4 times the thickness.
- Dimensions in mm, Weight in kg.
Tab. N° 12 Sheet 1 of 1
XIII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
30° t
L R=1.5ND
ND
NOTE: - Elbow not included in this table can be obtained by interpolation between tabulated values.
- The ends of the elbows will be tapered up to 50% of the thickness for a maximum length of 4 times the thickness.
- Dimensions in mm, Weight in kg.
Tab. N° 13 Sheet 1 of 1
XIV
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
90° t
A
R=1.5*ND
ND
NOTE: - Elbow not included in this table can be obtained by interpolation between tabulated values.
- 30°, 45°, 60°, and other angles are available on request.
- Dimensions in mm, Weight in kg.
XV
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 14 Sheet 1 of 2
CONCENTRIC AND ECCENTRIC REDUCER - PLAIN ENDS
L L
t
t
ND 2 ND 1
ND 1
ND 2
XVI
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 14 Sheet 2 of 2
ND 1 ND 2 L NP = 6 bar NP = 10 bar NP = 16 bar
t w t w t w
NOTE: - Reducer not included in this table can be obtained by interpolation between tabulated values.
- The ends of the reducers will be tapered up to 50% of the thickness for a maximum length of 4 times the thickness.
- Thickness in mm, Weight in kg.
XVII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 15 Sheet 1 of 2
CONCENTRIC AND ECCENTRIC REDUCER - BELL/SPIGOT
L
ND 1 ND 2
XVIII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 15 Sheet 2 of 2
ND 1 ND 2 L A NP = 6 bar NP = 10 bar NP = 16 bar
t w t w t w
350 300 1073 797 6.4 25.0 9.5 28.7 14.2 39.2
350 250 1121 845 6.4 22.2 9.5 25.7 14.2 36.0
350 200 1234 958 6.4 21.3 9.5 24.9 14.2 35.2
350 150 1344 1068 6.4 20.5 9.5 24.2 14.2 34.3
400 350 1112 836 7.1 30.8 10.6 36.8 16.0 50.8
400 300 1215 939 7.1 30.1 10.6 36.4 16.0 50.3
400 250 1263 987 7.1 27.2 10.6 33.3 16.0 46.7
400 200 1376 1100 7.1 26.3 10.6 32.4 16.0 45.9
450 400 1219 904 7.8 41.2 11.8 50.1 17.4 68.8
450 350 1327 1012 7.8 40.5 11.8 49.7 17.4 69.1
450 300 1430 1115 7.8 39.7 11.8 49.2 17.4 68.4
450 250 1478 1163 7.8 36.6 11.8 45.7 17.4 64.4
500 450 1329 1014 8.3 58.1 12.6 68.5 19.2 94.1
500 400 1364 1049 8.3 50.0 12.6 60.0 19.2 85.3
500 350 1472 1157 8.3 49.3 12.6 59.6 19.2 85.7
500 300 1575 1260 8.3 48.5 12.6 59.0 19.2 84.9
600 500 1508 1193 9.7 80.7 14.9 96.3 22.7 135.8
600 450 1613 1298 9.7 79.9 14.9 96.3 22.7 136.7
600 400 1648 1333 9.7 71.5 14.9 87.2 22.7 127.1
600 350 1756 1441 9.7 70.8 14.9 86.8 22.7 127.4
700 600 1582 1267 11.0 106.8 16.8 130.5 25.7 185.5
700 500 1798 1483 11.0 106.5 16.8 131.9 25.7 189.2
700 450 1903 1588 11.0 105.8 16.8 131.9 25.7 190.2
700 400 1938 1623 11.0 96.9 16.8 122.2 25.7 179.5
800 700 1665 1350 12.4 142.6 18.9 172.8 29.1 250.7
800 600 1875 1560 12.4 143.6 18.9 177.4 29.1 258.1
800 500 2091 1776 12.4 143.4 18.9 179.0 29.1 262.2
800 450 2196 1881 12.4 142.6 18.9 178.9 29.1 263.1
900 800 1805 1469 13.4 189.9 21.1 230.5 32.6 336.8
900 700 2012 1676 13.4 189.0 21.1 232.3 32.6 344.2
900 600 2222 1886 13.4 189.8 21.1 236.6 32.6 351.6
900 500 2438 2102 13.4 189.4 21.1 238.3 32.6 355.4
1000 900 1961 1615 14.8 254.4 22.8 305.9 36.0 451.4
1000 800 2114 1768 14.8 239.2 22.8 293.9 36.0 443.3
1000 700 2321 1975 14.8 238.3 22.8 295.7 36.0 451.1
1000 600 2531 2185 14.8 239.2 22.8 300.2 36.0 458.5
1200 1100 2099 1753 17.1 362.8 27.1 447.4 42.9 670.4
1200 1000 2349 2003 17.1 377.4 27.1 470.6 42.9 707.1
1200 900 2540 2194 17.1 379.3 27.1 476.3 42.9 719.7
1200 800 2693 2347 17.1 363.4 27.1 463.3 42.9 710.1
NOTE: - Reducer not included in this table can be obtained by interpolation between tabulated values.
- Thickness in mm, Weight in kg.
XIX
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 16 Sheet 1 of 2
EQUAL AND REDUCING TEE - PLAIN ENDS – FULL LAMINATED
ND2
L/2
d
ND
L/2
Tab. N° 16 Sheet 2 of 2
XX
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
NOTE: - Tees not included in this table can be obtained by interpolation between tabulated values.
- For header and branch thickness: tab. n° 2
- Internal lamination from ND 600: ti = 2 mm, Li = 100 mm.
- Dimensions in mm, Weight in Kg.
XXI
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 17 Sheet 1 of 2
EQUAL AND REDUCING TEE - BELL/SPIGOT/SPIGOT
ND2
L/2
ND1
XXII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 17 Sheet 2 of 2
ND1 ND2 L A NP = 6 bar NP = 10 bar NP = 16
bar
w w w
400 400 1185 909 46.9 55.6 65.1
400 300 1185 909 40.4 45.9 54.7
400 200 1185 909 32.4 38.1 43.6
450 450 1350 1035 71.5 83.6 101.2
450 350 1350 1035 58.1 66.9 81.5
450 250 1350 1035 48.8 56.8 69.5
500 500 1400 1085 88.4 92.4 125.5
500 400 1400 1085 71.4 77.8 102.8
500 300 1400 1085 63.3 66.4 89.6
500 250 1400 1085 57.5 61.7 82.0
600 600 1550 1235 121.5 138.8 188.2
600 500 1550 1235 107.2 121.4 165.7
600 400 1550 1235 88.9 104.8 138.1
600 300 1550 1235 80.1 91.0 121.9
700 700 1900 1585 169.6 201.5 277.5
700 600 1900 1585 155.6 181.7 253.5
700 500 1900 1585 138.1 160.3 224.2
700 350 1900 1585 112.5 132.6 180.9
800 800 2100 1785 240.2 281.5 397.2
800 700 2100 1785 214.6 252.7 355.6
800 600 2100 1785 198.5 229.3 327.3
800 500 2100 1785 178.1 204.4 292.8
800 400 2100 1785 154.3 183.5 256.6
900 900 2300 1964 346.9 405.6 567.4
900 800 2300 1964 304.9 357.6 504.2
900 700 2300 1964 275.7 324.7 456.6
900 450 2300 1964 222.4 262.0 365.4
1000 1000 2600 2254 459.7 516.8 764.2
1000 800 2600 2254 374.9 434.2 628.1
1000 600 2600 2254 320.8 365.0 535.6
1000 500 2600 2254 293.5 331.9 489.0
1200 1200 3000 2654 688.2 805.4 1235.1
1200 1000 3000 2654 601.6 698.6 1062.4
1200 800 3000 2654 499.6 599.8 895.0
1200 600 3000 2654 432.7 512.9 779.3
NOTE: - Tees not included in this table can be obtained by interpolation between tabulated values.
-Tees with other type of ends are available on request
-Thickness and reinforcement dimensions: tab. n° 16 for full laminated TEE.
- Dimensions in mm, Weight in Kg.
XXIII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 18 Sheet 1 of 2
EQUAL AND REDUCING TEE - BELL/SPIGOT/BELL
ND2
L/2
A/2
ND1
XXIV
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 18 Sheet 2 of 2
ND1 ND2 L A NP = 6 bar NP = 10 bar NP = 16
bar
w w w
400 400 1185 633 44.5 55.3 66.8
400 300 1185 633 38.1 45.5 56.4
400 200 1185 633 30.0 37.7 45.3
450 450 1350 720 64.1 79.5 101.3
450 350 1350 720 50.6 62.8 81.6
450 250 1350 720 41.4 52.7 69.6
500 500 1400 770 81.5 88.8 127.2
500 400 1400 770 64.5 74.2 104.5
500 300 1400 770 56.4 62.8 91.3
500 250 1400 770 50.7 58.1 83.7
600 600 1550 920 115.6 136.7 194.2
600 500 1550 920 101.3 119.3 171.7
600 400 1550 920 83.0 102.8 144.1
600 300 1550 920 74.2 88.9 127.9
700 700 1900 1270 163.7 204.6 290.3
700 600 1900 1270 149.7 184.4 266.3
700 500 1900 1270 132.3 163.4 237.0
700 350 1900 1270 106.6 135.7 193.7
800 800 2100 1470 235.0 287.4 418.5
800 700 2100 1470 209.4 258.6 376.9
800 600 2100 1470 193.2 235.2 348.7
800 500 2100 1470 172.9 210.3 314.1
800 400 2100 1470 149.0 189.4 277.9
900 900 2300 1628 330.4 402.4 585.8
900 800 2300 1628 288.5 354.4 522.7
900 700 2300 1628 259.3 321.5 475.1
900 450 2300 1628 205.9 258.8 383.9
1000 1000 2600 1908 443.6 516.0 791.0
1000 800 2600 1908 358.8 433.4 654.9
1000 600 2600 1908 304.6 364.2 562.4
1000 500 2600 1908 277.4 331.1 515.8
1200 1200 3000 2308 677.6 816.8 1286.0
1200 1000 3000 2308 591.0 710.0 113.2
1200 800 3000 2308 489.0 611.2 945.8
1200 600 3000 2308 422.2 524.3 830.2
NOTE: - Tees not included in this table can be obtained by interpolation between tabulated values.
-Tees with other type of ends are available on request
-Thickness and reinforcement dimensions: tab. n° 16 for full laminated TEE.
- Dimensions in mm, Weight in Kg.
XXV
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 19 Sheet 1 of 2
EQUAL AND REDUCING TEE - FIXED FLANGE
ND2
L/2
ND1
XXVI
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 19 Sheet 2 of 2
NP = 6 bar NP = 10 bar NP = 16 bar
ND1 ND2 L w w w
UNI UNI ANSI 150 UNI ANSI 150
400 400 900 44.2 71.0 79.4 90.9 100.9
400 300 900 38.0 57.7 66.0 75.4 84.5
400 200 900 30.8 50.0 55.7 62.4 69.1
450 450 1000 56.8 87.1 91.1 122.6 118.2
450 350 1000 49.0 73.3 78.0 101.6 100.0
450 250 1000 40.8 62.4 65.7 86.9 84.5
500 500 1100 73.8 101.5 1094 168.2 159.4
500 400 1100 62.2 90.0 98.0 139.8 137.3
500 300 1100 54.4 75.1 83.0 121.5 118.1
500 250 1100 49.5 71.0 76.9 113.3 108.0
600 600 1300 108.7 153.0 169.2 272.5 246.2
600 500 1300 93.8 133.8 147.2 235.3 214.9
600 400 1300 80.8 120.3 133.9 201.7 187.6
600 300 1300 72.3 102.7 116.2 180.4 165.3
700 700 1780 166.2 241.6 260.6 363.3 385.2
700 600 1780 150.2 213.0 231.0 338.7 344.6
700 500 1780 131.8 189.2 204.5 294.1 305.8
700 350 1780 111.3 162.0 176.6 241.1 257.1
800 800 2020 241.3 338.6 366.8 519.9 553.7
800 700 2020 214.5 303.8 329.0 464.1 493.9
800 600 2020 196.2 271.5 295.7 435.1 448.8
800 500 2020 174.8 244.1 265.5 385.0 404.6
800 400 2020 155.9 225.9 247.5 342.1 368.0
900 900 2250 325.5 457.2 501.7 702.0 757.8
900 800 2250 295.2 414.6 453.7 636.8 685.2
900 700 2250 264.7 375.6 411.6 574.7 619.2
900 450 2250 207.6 299.3 330.4 459.2 494.9
1000 1000 2400 426.6 601.3 651.2 984.8 1044.3
1000 800 2400 354.8 509.5 552.2 810.5 861.5
1000 600 2400 298.2 426.2 464.9 704.7 735.6
1000 500 2400 270.2 391.1 427.0 643.2 679.9
1200 1200 2800 687.7 978.7 1053.7 1615.6 1730.4
1200 1000 2800 588.4 838.2 904.9 1381.5 1477.9
1200 800 2800 499.5 730.2 789.6 1176.0 1263.8
1200 600 2800 430.1 629.3 684.7 1046.9 1114.7
NOTE: - Tees not included in this table can be obtained by interpolation between tabulated values.
- Tees with stub end and loose flange are available.
-Thickness and reinforcement dimensions: full laminated TEE tab. n° 16; flange dimensions: tab n° 21
- Dimensions in mm, Weight in Kg.
Tab. N° 20 Sheet 1 of 3
XXVII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
df
R5
5
5
0.4 Ds a Dl ml ND ms
tl
el
NP = 6 bar
UNI PN6 DRILLING
ND Stub end Backing ring
L tl el ml Dl w Ds a N°f df db ts w
XXVIII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 20 Sheet 2 of 3
NP = 10 bar - UNI PN10 DRILLING
ND Stub end Backing ring
L tl el ml Dl w Ds a N°f df db ts w
XXIX
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 20 Sheet 3 of 3
NP = 16 bar - UNI PN16 DRILLING
ND Stub end Backing ring
L tl el ml Dl w Ds a N°f df db ts w
XXX
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 21 Sheet 1 of 3
FIXED FLANGE - PLAIN END
ef
tf
df
5 R5
5
0.4
Df a mf ND
XXXI
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 21 Sheet 2 of 3
NP = 10 bar - UNI PN10 DRILLING
ND L tf ef mf Df a N°f df db w
XXXII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 21 Sheet 3 of 3
NP = 16 bar - UNI PN16 DRILLING
ND L tf ef mf Df a N°f df db w
XXXIII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 22 Sheet 1 of 1
LOOSE FLANGE ADAPTER - BELL END
ND
NOTE: - Stub dimensions for intermediate internal pressure class can be obtained by interpolation between tabulated values.
- Weight related to lamination, pipe and backing ring.
- Drilling according to the relevant Standard
- Dimensions in mm, Weight in kg.
- Standard gasket: flat NEOPRENE gasket. Stub with O - ring gasket needs a groove in the face.
XXXIV
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 23 Sheet 1 of 1
LOOSE FLANGE ADAPTER - SPIGOT END
ND
NP = 10 bar NP = 16 bar
ND L UNI ANSI 150 UNI ANSI 150
w w w w
25 365 0.9 1.4 1.4 1.4
40 365 1.6 2.5 1.9 2.5
50 365 1.9 3.4 2.7 3.4
75 375 3.7 5.2 4.4 5.2
100 385 4.0 6.2 5.8 6.1
125 435 5.8 8.7 7.6 8.6
150 445 7.7 11.3 9.3 11.1
200 445 10.6 15.4 12.7 14.9
250 455 14.1 19.9 17.4 23.6
300 505 20.0 24.9 28.1 30.9
350 535 24.3 32.6 34.9 41.5
400 635 29.6 42.4 44.1 53.9
450 695 40.8 53.7 53.1 73.0
500 705 47.8 62.7 64.3 93.4
600 735 62.0 84.1 95.7 131.2
700 735 82.2 112.8 127.7 147.0
800 735 117.2 150.0 176.3 198.6
900 735 160.5 197.3 235.8 253.5
1000 755 192.2 244.5 298.3 336.2
1200 855 265.3 355.3 426.8 509.2
NOTE: - Stub dimensions for intermediate internal pressure class can be obtained by interpolation between tabulated values.
- Weight related to lamination, pipe and backing ring.
- Drilling according to the relevant Standard
- Dimensions in mm, Weight in kg.
- Standard gasket: flat NEOPRENE gasket. Stub with O - ring gasket needs a groove in the face.
XXXV
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 24 Sheet 1 of 1
FLANGE ADAPTER - BELL END
ND
NOTE: - Flange dimensios for intermediate internal pressure class can be obtained by interpolation between tabulated values.
- Weight related to the lamination and pipe.
- Drilling according to the relevant Standard
- Dimensions in mm, Weight in kg.
- Standard gasket: flat NEOPRENE gasket. Flange with O - ring gasket needs a groove in the face.
XXXVI
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 25 Sheet 1 of 1
FLANGE ADAPTER - BELL END
ND
NOTE: - Flange dimensions for intermediate internal pressure class can be obtained by interpolation between tabulated values.
- Weight related to the lamination and pipe.
- Drilling according to the relevant Standard
- Dimensions in mm, Weight in kg.
- Standard gasket: flat NEOPRENE gasket. Flange with O - ring gasket needs a groove in the face.
Tab. N° 26 Sheet 1 of 1
XXXVII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
BLIND FLANGES
tf
Df
ND tf Df w tf Df w tf Df w tf Df w tf Df w
25 14 100 0.2 20 115 0.3 20 108 0.3 20 115 0.3 20 108 0.3
40 14 130 0.3 22 150 0.6 22 127 0.4 22 150 0.6 22 127 0.4
50 14 140 0.3 22 165 0.7 22 152 0.6 22 165 0.7 22 152 0.6
75 16 190 0.7 25 200 1.2 25 190 1.1 25 200 1.2 25 190 1.1
100 16 210 0.9 26 220 1.5 26 228 1.6 26 220 1.5 26 228 1.6
125 16 240 1.1 27 250 2.1 27 254 2.1 27 250 2.1 27 254 2.1
150 17 265 1.5 30 285 3.0 30 279 2.8 30 285 3.0 30 279 2.8
200 20 320 2.5 30 340 4.2 30 343 4.3 35 340 4.9 35 343 5.0
250 24 375 4.1 32 395 6.1 32 406 6.4 40 405 8.0 40 406 8.0
300 28 440 6.6 36 445 8.7 36 483 10.2 46 460 11.8 46 483 13.1
350 32 490 9.4 40 505 12.4 40 533 13.8 50 520 16.5 50 533 17.3
400 34 540 12.1 44 565 17.1 44 597 19.1 56 580 22.9 56 597 24.3
450 38 595 16.4 50 615 23.0 50 635 24.5 62 640 30.9 62 635 30.4
500 42 645 21.3 54 670 29.5 54 699 32.1 68 715 42.3 68 699 40.4
600 48 755 33.3 62 780 45.9 62 813 49.9 78 840 67.0 78 813 62.8
NO - Flange dimensions for intermediate internal pressure class can be obtained by interpolation between tabulated values.
TE:
- Drilling according to the relevant Standard
- Dimensions in mm, Weight in kg.
XXXVIII
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 27 Sheet 1 of 1
CAP
ND
NOTE: - Cap not included in this table can be obtained by interpolation between tabulated values.
- The ends of the caps will be tapered up to 50% of the thickness for a length of 4 times the thickness.
- Dimensions in mm, Weight in kg.
XXXIX
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 28 Sheet 1 of 1
BELL / SPIGOT END – DOUBLE O—RING LOCK JOINT
Bf
ND
XL
PRODUCT LIST Doc N°: STD/CAT-001
Iniziative Industriali S.p.A. Release. 3
Date : 01.03.99
Tab. N° 29 Sheet 1 of 1
BUTT & STRAP JOINT
L
L
t
t
ti
ti
Li
Li
XLI