Professional Documents
Culture Documents
BRAY.COM/FLOW-TEK
FEATURES AND BENEFITS
1 Emergency Stem Sealant Injection 8 Double Seals on Body Joints
This standard feature allows the valve’s stem housing Primary elastomeric seals ensure zero leakage in standard
to be adapted with a grease fitting to inject sealant operating conditions. Secondary graphite seals ensure
during emergency scenarios. By filling the cavity between proper body joint sealing per API 607 in extreme
the stem and stem housing, this secondary stem seal temperature scenarios.
provides protection against unplanned spikes in operating
conditions. 9 Anti-Static Devices
Anti-static devices are provided as standard. These devices
2 Emergency Seat Sealant Injection ensure electrical continuity between the ball, stem, and
This optional feature allows the valve’s end connections body, eliminating the possibility of static electrical charges
to be adapted with a grease fitting to inject sealant. This creating sparks within the valve.
creates a positive seal in the case of seat leakage due
to service impurities or unplanned spikes in operating 10 Valve Position Indication
Clear stamping on the outer diameter of the mounting
conditions.
flange identifies the open or closed position of the valve,
3 Drain and Vent Ports based on the stem key orientation.
Drain ports located at the bottom of the valve allow for
elimination of any fluid trapped in the body cavity of a
11 ISO 5211 Mounting Pad
Robust ISO 5211 mounting pad provides quick conversion
closed valve. Vent ports located at the top of the body
between the valve and the automation package.
cavity allow for elimination of any gas trapped in the body
cavity of a fully closed valve. Both play a key safety role in 12 Blowout-proof Stem Design
a double block and bleed and double isolation and bleed Valves are designed with stem/body connection preventing
valve configurations. stem blowout under line pressure.
11
7
1
12
9
3
5
6
2
4
6
8
1 2 5 8
DESIGN FEATURES
Single Piston Effect Double Piston Effect
With this design, pressurized media upstream of the seat results This seat design uses pressure on both sides of the seat to assist
in a force pushing the seat toward the ball. As temperatures rise, sealing. As seen below, pressurized media upstream of the seat
media trapped inside the body cavity builds up excessive pressure. results in a force pushing the seat toward the ball. Similarly, when
This pressure pushes the seat away from the ball, compresses the the pressurized media is inside the body cavity, the resulting force
seat springs, and allows the media to relieve past the seat. This pushes the seat toward the ball. This sealing effect doesn’t allow
self-relieving seat design allows for safe operation without the for self-relieving of cavity pressure and, in turn, requires a bleed
need for dedicated bleed lines. line be installed within the body cavity. This type of valve config-
uration is valuable in applications where two redundant seals are
Single Piston Upstream Pressure required in the same direction (e.g. when repairs are being made
downstream in a toxic service line). If media were to get past the
upstream seal, dangerous flow toward the technician would be
blocked by the downstream seal and evacuated by the bleed line.
4 | BRAY.COM/FLOW-TEK
PRESSURE TEMPERATURE CHART
ine
mL
1400 psig Class 600 stainless steel 97 bar
Stea
d
rate
Satu
Carbon Steel Min. Temp.
0 psig 0 bar
-50°F 50°F 150°F 250°F 350°F 450°F 550°F 650°F
APPLICATIONS
• Oil and Gas Pipeline • Metering Stations
• Offshore Platforms • Pig Traps
• Onshore Terminals • Surge-Relief Skids
• Emergency Shutdown • Decoking Isolation
• Suction and Discharge • Buried Services
Isolation
• Produced Water (Brine)
• Block and Bypass Services
14
15
34
33
13 19
21
23 29 11
20 10
22
18
2
17
9
12 7
32
3 8
5
1
4
30
31
6 | BRAY.COM/FLOW-TEK
DIMENSIONS
Size: 2"-4" Size: 6"-24"
Y Y BC KxL
BC
KxL
X X
Top enlarged for visual purposes only. Top enlarged for visual purposes only.
H J H J
ØB
ØB
C C
C1 ØG
ØG C1
ØF ØF
C2
C2
A D A D
Dimensions provided are for reference. Please contact factory for additional or more specific information.
*Valve sizes without key dimensions shown in the table utilize a double "D" style stem. Please contact factory for detailed dimensions.
**Valve torques mentioned above do not contain a safety factor and are not applicable to PEEK seated valves. Please refer to Technical Bulletin 1005 for more detailed information.
All statements, technical information, and recommendations in this bulletin are for general use only. Consult Flow-
Tek representatives or factory for the specific requirements and material selection for your intended application.
The right to change or modify product design or product without prior notice is reserved.
Flow-Tek® is a registered trademark of Bray International, Inc.
© 2019 Bray International, Inc. All rights reserved. F-2811 TMBValves 06-2019