Professional Documents
Culture Documents
Panel de Incendio XLS120 74-5144-2 PDF
Panel de Incendio XLS120 74-5144-2 PDF
Intelligent Addressable
Fire Alarm System
General
In stand-alone or network configurations, Honeywell’s XLS120
meets virtually every application requirement.
The XLS120‘s modular design makes system planning easier.
The panel can be configured with just a few devices for small
building applications, or networked with many devices to pro-
tect a large campus or a high-rise office block. Simply add
additional peripheral equipment to suit the application.
xls120cov.jpg
For installations using XLS120C, an optional ACM Series
annunciator can be mounted in the same cabinet (up to 48
zones/points, order separately).
When combined with a Honeywell Enterprise Buildings Inte- XLS120
grator (EBI), the XLS120 becomes part of an owner-operated
proprietary monitoring system, allowing the connection of
standalone or networked panels. – California two-stage coding.
NOTE: Unless called out with a version-specific “C” or “E” at the – Canadian two-stage.
end of the part number, “XLS120” refers to models XLS120, – Strobe synchronization.
XLS120C, and XLS120E.
• Field-programmable on panel or on PC, with VeriFire®
Tools program check, compare, simulate.
Features
• Full QWERTY keypad.
• Certified for seismic applications when used with the appro- • Battery charger supports 18 – 200 AH batteries.
priate seismic mounting kit.
• Non-alarm points for lower priority functions.
• One isolated intelligent Signaling Line Circuit (SLC) Style 4,
6 or 7. • Remote ACK/Signal Silence/System Reset/Drill via monitor
modules.
• Up to 159 detectors (any mix of ion, photo, thermal, or
multi-sensor) and 159 modules (Addressable pull stations, • Automatic time control functions, with holiday exceptions.
normally open contact devices, two-wire smoke, notifica- • Extensive, built-in transient protection.
tion, or relay). 318 devices maximum. • Powerful Boolean logic equations.
• Standard 80-character display.
FLASHSCAN® INTELLIGENT FEATURES
• Network options:
– High-speed network for up to 200 nodes (XLS3000, • Poll up to 318 devices in less than two seconds.
XLS140-2, XLS140, XLS120(C), XLS-NCA/-NCA2 Net- • Activate up to 159 outputs in less than five seconds.
work Annunciator, or XLS-DVC, and Honeywell Enter- • Multicolor LEDs blink device address during Walk Test.
prise Buildings Integrator™ [EBI]).
• Fully digital, high-precision protocol (U.S. Patent
– Standard network for up to 103 nodes (XLS3000, 5,539,389).
XLS140-2, XLS120(C), XLS-NCA2 Network Annunciator,
• Manual sensitivity adjustment — nine levels.
or XLS-DVC, and Honeywell Enterprise Buildings Integra-
tor™ [EBI]). Up to 54 nodes when DVC is used in network • Pre-alarm intelligent sensing — nine levels.
paging. • Day/Night automatic sensitivity adjustment.
• 6.0 A power supply with four Class A/B built-in Notification • Sensitivity windows:
Appliance Circuits (NAC). Selectable System Sensor, – Ion – 0.5 to 2.5%/foot obscuration.
Wheelock, or Gentex strobe synchronization.
– Photo – 0.5 to 2.35%/foot obscuration.
• Built-in Alarm, Trouble, Security, and Supervisory relays.
– Laser (Pinnacle™) – 0.02 to 2.0%/foot obscuration.
• Autoprogramming and Walk Test reports.
– Acclimate® – 0.5 to 4.0%/foot obscuration.
• Optional universal 318-point DACT.
– COPTIR – 1.0 to 4.0%/foot obscuration.
• 80-character remote annunciators (up to 32).
• Drift compensation (U.S. Patent 5,764,142).
• EIA-485 annunciators, including custom graphics.
• Degraded mode — in the unlikely event that the XLS120’s
• Printer interface (80-column and 40-column printers). primary microprocessor fails, FlashScan detectors revert to
• History file with 800-event capacity in nonvolatile memory, degraded operation and can activate the control panel’s
plus separate 200-event alarm-only file. NAC circuits and alarm relay. Each of the four built-in panel
• Alarm Verification selection per point, with tally. circuits includes a Disable/Enable switch for this feature.
• Presignal/Positive Alarm Sequence (PAS). • Multi-detector algorithm involves nearby detectors in alarm
decision (U.S. Patent 5,627,515).
• Silence inhibit and Auto Silence timer options.
• Automatic detector sensitivity testing (NFPA-72 compliant).
• NAC coding functions:
• Maintenance alert (two levels).
– March time.
• Self-optimizing pre-alarm.
– Temporal.
TC846A1013 PINNACLE LASER SMOKE DETECTION TC840C2010 ADVANCED MULTI-CRITERIA FIRE/CO
TECHNOLOGY DETECTOR
• Revolutionary spot laser design. • Detects all four major elements of a fire.
• Advanced intelligent sensing algorithms differentiate • Separate signal for life-safety CO detection.
between smoke and non-smoke signals (U.S. Patent • Optional addressable sounder base for Temp-3 (fire) or
5,831,524). Temp-4(CO) tone.
• Addressable operation pinpoints the fire location. • Automatic drift compensation of smoke sensor and CO cell.
• No moving parts to fail or filters to change. • High nuisance-alarm immunity.
• Early warning performance comparable to the best aspira- • Six sensitivity levels.
tion systems at a fraction of the lifetime cost.
RELEASING FEATURES
TC840M1021 ACCLIMATE®
• Ten independent hazards.
LOW-PROFILE INTELLIGENT MULTI-SENSOR
• Sophisticated cross-zone (three options).
• Detector automatically adjusts sensitivity levels without
operator intervention or programming. Sensitivity increases • Delay timer and Discharge timers (adjustable).
with heat. • Abort (four options).
• Microprocessor-based technology; combination photo and • Low-pressure CO2 listed.
thermal technology.
HIGH-EFFICIENCY OFFLINE SWITCHING
• FlashScan or CLIP (standard polling of each intelligent
device) mode compatible.
3.0 A POWER SUPPLY (6.0 A IN ALARM)
• Low-temperature warning signal at 40°F ± 5°F (4.44°C ± • 120 VAC (XLS120/XLS120C); 240 VAC (XLS120E).
2.77°C). • Displays battery current/voltage on panel (with display).
XLS120
Sample
System
Options
h7112blok.wmf
Keypad Program Edit (with KDM-R2) The XLS120 has the RPT-W, RPT-F, RPT-WF: Repeater board with wire connection
exclusive feature of the product line of program creation and (RPT-W), fiber connection (RPT-F), or allowing a change in
editing capability from the front panel keypad, while continuing media type between wire and fiber (RPT-WF). Not used with
to provide fire protection. The architecture of the XLS120 soft- high-speed networks. See 85-3007.
ware is such that each point entry carries its own program, Q7055B1039: Fire Network Adapter. Connects to an
including control-by-event links to other points. This allows the XLS•NET network to provide a TCP/IP interface to an EBI.
program to be entered with independent per-point segments,
while the XLS120 simultaneously monitors other (already AUXILIARY POWER SUPPLIES AND BATTERIES
installed) points for alarm conditions. ACPS-610: 6.0 A or 10 A addressable charging power supply.
VeriFire® Tools is an offline programming and test utility that See 85-3109.
can greatly reduce installation programming time, and APS2-6R: Auxiliary power supply. Provides two 24 VDC cir-
increase confidence in the site-specific software. It is Win- cuits, each rated for 3.0 A in alarm and 2.0 A continuous. Com-
dows®-based and provides technologically advanced capabili- monly used for the operation of peripheral audio/visual devices
ties to aid the installer. The installer may create the entire or any other application requiring 24VDC. See 74-5072.
program for the XLS120 in the comfort of the office, test it,
HPF24S6/S8: Remote 6 A and 8 A power supplies with battery
store a backup file, then bring it to the site and download from
charger. In Canadian applications, for use only as a NAC
a laptop into the panel.
expander. DH-1061
KDM-R2 Controls and Indicators BAT Series: Batteries. XLS120 uses two 12 volt, 18 to 200 AH
batteries.
Program Keypad: QWERTY type (keyboard layout).
COMPATIBLE DEVICES, EIA-232 PORTS
12 LED Indicators: Power; Fire Alarm; Pre-Alarm; Security;
Supervisory; System Trouble; Signals Silenced; Points Dis- XLS-PRN-6: 80-column printer. See 83-3073.
abled; Control Active; Abort; Pre-Discharge; Discharge. VS4095/5: Printer, 40-column, 24 V. Mounted in external back-
box.
This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific
applications or anticipate all requirements. All specifications are subject to change without notice.
Pinnacle™ is a trademarks; and Acclimate®, FlashScan®, VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc. Microsoft®
and Windows® are registered trademarks of Microsoft Corporation. IBM® is a registered trademark of IBM Corporation.
©2011 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.