Professional Documents
Culture Documents
7 Performance
This chapter describes the performance indexes of the OptiX RTN 600.
1 4xE1 QPSK 7
4 8xE1 16QAM 7
NOTE
l When the OptiX RTN 600 adopts the LP series ODU, mode 7 is not supported.
l When the OptiX RTN 600 adopts the HP series ODU, mode 2 is not supported.
l 13.75 MHz and 27.5 MHz are applied for 18 GHz.
l The channel spacing described in the table is the minimum channel spacing supported by the equipment.
The channel spacing larger than the value is also supported.
Frequency Band
NOTE
Receiver Sensitivity
Table 7-5 Typical values of the receiver sensitivity with the SP series ODU adopted
Item Performance
NOTE
Table 7-6 Typical values of the receiver sensitivity with the HP series ODU adopted
Item Performance
Item Performance
NOTE
Table 7-7 Typical values of the receiver sensitivity with the LP series ODU adopted
Item Performance
NOTE
Transceiver Performance
@6 GHz 26 24 23
@18 GHz 24 20 14
@26 GHz 22 18 12
@7 GHz 30 28 24
@8 GHz 30 28 24
@11 GHz 28 26 21
@13 GHz 26 23 18
@15 GHz 26 23 18
Item Performance
@23 GHz 25 22 17
@26 GHz 25 22 17
@32 GHz 23 21 16
@38 GHz 23 20 16
@7 GHz 9
@8 GHz 9
@11 GHz 6
@13 GHz 3
@15 GHz 3
@18 GHz 2
@23 GHz 2
@26 GHz 2
@32 GHz 1
@38 GHz 1
QPSK 16QAM
@7GHz 27 21
@8GHz 27 21
@11GHz 25 19
@13GHz 25 19
Item Performance
QPSK 16QAM
@23GHz 23 17
Anti-Multipath Fading
IF Performance
IF signal
Impedance (ohm) 50
Adaptive time- Consisting of the 24-tap feed forward equalizer filter and the 3-tap
domain equalizer for decision feedback equalizer
baseband signals
Item Performance
MTTR (h) 1 1 1
Item Performance
MTTR (h) 1 1
Item Performance
Operating wavelength 1270 to 1380 1261 to 1360 1280 to 1335 1480 to 1580
(nm)
Item Performance
NOTE
All optical interface boards use the small form-factor pluggable (SFP) optical modules to provide optical
interfaces. To provide optical interfaces with different classification codes or transmission distances, use the
SFP optical modules of different types.
Item Performance
Impedance (ohm) 75
E1 Interface
The performances of the E1 interface are compliant with ITU-T G.703. The following table
provides the primary performances.
Item Performance
Wire pair in each One coaxial wire pair One symmetrical wire pair
transmission direction
Item Performance
10/100BASE-T(X) Interface
The 10/100BASE-T(X) interface conforms to IEEE 802.3u. The following table provides the
primary performances.
Orderwire Interface
Transmission path Uses the E1 and E2 bytes in the SDH overhead or the user-
defined byte in the overhead of the microwave frame.
Transmission path Uses the user-defined byte in the overhead of the microwave
frame.
Item Performance
Impedance (ohm) 75
Item Performance
Transmission path Uses any byte in serial 1 to serial 4 of the SDH overhead or
the user-defined byte in the overhead of the microwave frame.
Item Performance
Item Performance
Item Performance
Noise generation
Noise tolerance
Noise transfer
Dimensions
Weight
Power Supply
Component Performance
Power Consumption
EMC
l Passes CE authentication.
l Compliant with ETSI EN 301 489-1.
l Compliant with ETSI EN 301 489-4.
l Compliant with EN 55022 CLASS B.
l Compliant with CISPR 22.
Lightning Protection
l Compliant with ITU-T K.27.
l Compliant with ETSI EN 300 253.
Safety
l Passes CE authentication.
l Compliant with ETSI EN 60215.
l Compliant with ETSI EN 60950.
l Compliant with IEC 60825.
Environment
The IDU is a unit used in a place that has weather protection and where the temperature can be
controlled. The ODU is an outdoor unit.
IDU ODU