Professional Documents
Culture Documents
1
Company: JPT Page: 1
Specifier: Project: Jade Hills - RSKU
Address: Sub-Project I Pos. No.: Lifting Hook Alt -4
Phone I Fax: | Date: 28/11/2016
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200-R + HIT-V-F (8.8) M10
Seismic/Filling set or any suitable annular gap filling solution
Effective embedment depth: hef,opti = 90 mm (hef,limit = 120 mm)
Material: 8.8
Evaluation Service Report: ETA 12/0084
Issued I Valid: 15/4/2015 | 15/4/2020
Proof: Engineering judgement SOFA BOND - based on ETAG BOND testing
Stand-off installation: eb = 0 mm (no stand-off); t = 14 mm
Anchor plate: lx x ly x t = 580 mm x 160 mm x 14 mm; (Recommended plate thickness: not calculated
Profile: no profile
Base material: uncracked concrete, C25/30, fc = 30.00 N/mm2; h = 150 mm, Temp. short/long: 30/30 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.7.1
Company: JPT Page: 2
Specifier: Project: Jade Hills - RSKU
Address: Sub-Project I Pos. No.: Lifting Hook Alt -4
Phone I Fax: | Date: 28/11/2016
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.7.1
Company: JPT Page: 3
Specifier: Project: Jade Hills - RSKU
Address: Sub-Project I Pos. No.: Lifting Hook Alt -4
Phone I Fax: | Date: 28/11/2016
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.7.1
Company: JPT Page: 4
Specifier: Project: Jade Hills - RSKU
Address: Sub-Project I Pos. No.: Lifting Hook Alt -4
Phone I Fax: | Date: 28/11/2016
E-Mail:
baN + baV ≤ 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.7.1
Company: JPT Page: 5
Specifier: Project: Jade Hills - RSKU
Address: Sub-Project I Pos. No.: Lifting Hook Alt -4
Phone I Fax: | Date: 28/11/2016
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7 Warnings
• Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger
diameters of the clearance hole see Chapter 1.1. of EOTA TR029!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• Bore hole cleaning must be performed according to instructions for use (blow 4 times with the hand pump, brush 4 times, blow again 4 times
with the hand pump).
• Characteristic bond resistances depend on short- and long-term temperatures.
• Please contact Hilti to check feasibility of HIT-V rod supply.
• The design method SOFA assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling
the gap with mortar of sufficient compressive strength (e.g. by using the HILTI Seismic/Filling set) or by other suitable means
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• An SLS-check is not performed for SOFA and has to be provided by the user!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.7.1
Company: JPT Page: 6
Specifier: Project: Jade Hills - RSKU
Address: Sub-Project I Pos. No.: Lifting Hook Alt -4
Phone I Fax: | Date: 28/11/2016
E-Mail:
8 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200-R + HIT-V-F (8.8) M10
Profile: no profile Installation torque: 0.020 kNm
Hole diameter in the fixture: df = 12 mm Hole diameter in the base material: 12 mm
Plate thickness (input): 14 mm Hole depth in the base material: 90 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 120 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
290 290
30
1 2 3 4
80
100
80
5 6 7 8 30
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan