Professional Documents
Culture Documents
06527-001
(Not to Scale)
V– 4 5 +INB
Wide bandwidth: 24 MHz
Slew rate: 11 V/μs Figure 1. 8-Lead SOIC and MSOP
Short-circuit output current: 120 mA
OUTA 1 10 V+
Qualified for automotive applications
–INA 2 9 OUTB
No phase reversal AD8647
+INA 3 TOP VIEW 8 –INB
Low input bias current: 1 pA V– 4 (Not to Scale) 7 +INB
06527-002
Low supply current per amplifier: 2 mA maximum SDA 5 6 SDB
Unity gain stable
Figure 2. 10-Lead MSOP
APPLICATIONS
OUTA 1 14 OUTD
Battery-powered instruments
–INA 2 13 –IND
Multipole filters
+INA 3 AD8648 12 +IND
ADC front ends TOP VIEW
V+ 4 11 V–
(Not to Scale)
Sensors
+INB 5 10 +INC
Barcode scanners
–INB 6 9 –INC
ASIC input or output amplifiers
06527-003
OUTB 7 8 OUTC
Audio amplifiers
Photodiode amplifiers Figure 3. 14-Lead SOIC and TSSOP
Datapath/mux/switch control
GENERAL DESCRIPTION
The AD8646 and the AD8647 are the dual, and the AD8648 is AD8647/AD8648 offer high output drive capability, which is
the quad, rail-to-rail, input and output, single-supply amplifiers excellent for audio line drivers and other low impedance
featuring low offset voltage, wide signal bandwidth, low input applications. The AD8646 and AD8648 are available for
voltage, and low current noise. The AD8647 also has a low automotive applications (see the Ordering Guide).
power shutdown function. Applications include portable and low powered instrumenta-
The combination of 24 MHz bandwidth, low offset, low noise, tion, audio amplification for portable devices, portable phone
and very low input bias current makes these amplifiers useful in headsets, barcode scanners, and multipole filters. The ability to
a wide variety of applications. Filters, integrators, photodiode swing rail to rail at both the input and output enables designers
amplifiers, and high impedance sensors all benefit from the to buffer CMOS ADCs, DACs, ASICs, and other wide output
combination of performance features. AC applications benefit swing devices in single-supply systems.
from the wide bandwidth and low distortion. The AD8646/
TABLE OF CONTENTS
Features .............................................................................................. 1 ESD Caution...................................................................................6
Applications ....................................................................................... 1 Typical Performance Characteristics ..............................................7
Pin Configurations ........................................................................... 1 Theory of Operation ...................................................................... 15
General Description ......................................................................... 1 Power-Down Operation ............................................................ 15
Revision History ............................................................................... 2 Multiplexing Operation ............................................................. 15
Specifications..................................................................................... 3 Outline Dimensions ....................................................................... 16
Absolute Maximum Ratings............................................................ 6 Ordering Guide .......................................................................... 18
Thermal Resistance ...................................................................... 6
REVISION HISTORY
Revision History: AD8646/AD8647/AD8648 Revision History: AD8646
8/2016—Rev. E to Rev. F 10/2007—Rev. 0 to Rev. B
Changes to Figure 18 and Figure 21 ............................................... 9 Combined with AD8648 ................................................... Universal
Changes to Figure 39 ...................................................................... 12 Added AD8647 ................................................................... Universal
Deleted Figure 4 and Figure 7 ..........................................................7
3/2014—Rev. D to Rev. E Deleted Figure 33............................................................................ 11
Changes to Differential Input Voltage, Table 3 ............................. 6
8/2007—Revision 0: Initial Version
4/2010—Rev. C to Rev. D
Changes to Features Section and General Description Section . 1 Revision History: AD8648
Updated Outline Dimensions ....................................................... 16 10/2007—Rev. A to Rev. B
Changes to Ordering Guide Section ............................................ 18 Combined with AD8646 ................................................... Universal
Added AD8647 ................................................................... Universal
2/2009—Rev. B to Rev. C Deleted Figure 7 .................................................................................6
Change to Supply Current Shutdown Mode (AD8647 Only) Deleted Figure 11...............................................................................7
Parameter, Table 1............................................................................. 3 Deleted Figure 16 and Figure 17 .....................................................8
Change to Supply Current Shutdown Mode (AD8647 Only) Deleted Figure 24...............................................................................9
Parameter, Table 2............................................................................. 5 Deleted Figure 27, Figure 28, Figure 31, and Figure 32 ............ 10
Added Figure 50; Renumbered Sequentially .............................. 15
Updated Outline Dimensions ....................................................... 16 6/2007—Rev. 0 to Rev. A
Changes to Ordering Guide .......................................................... 18 Changes to General Description .....................................................1
Updated Outline Dimensions ....................................................... 12
10/2007—Revision B: Initial Combined Version Changes to Ordering Guide .......................................................... 12
Rev. F | Page 2 of 18
Data Sheet AD8646/AD8647/AD8648
SPECIFICATIONS
VSY = 5 V, VCM = VSY/2, TA = +25oC, unless otherwise noted.
Table 1.
Parameter Symbol Conditions Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage VOS VCM = 0 V to 5 V 0.6 2.5 mV
−40°C < TA < +125°C 3.2 mV
Offset Voltage Drift ΔVOS/ΔT −40°C < TA < +125°C 1.8 7.5 μV/°C
Input Bias Current IB 0.3 1 pA
−40°C < TA < +85°C 50 pA
−40°C < TA < +125°C 550 pA
Input Offset Current IOS 0.1 0.5 pA
−40°C < TA < +85°C 50 pA
−40°C < TA < +125°C 250 pA
Input Voltage Range VCM 0 5 V
Common-Mode Rejection Ratio CMRR VCM = 0 V to 5 V 67 84 dB
Large Signal Voltage Gain AVO RL = 2 kΩ, VO = 0.5 V to 4.5 V 104 116 dB
Input Capacitance
Differential CDIFF 2.5 pF
Common Mode CCM 6.7 pF
OUTPUT CHARACTERISTICS
Output Voltage High VOH IOUT = 1 mA 4.98 4.99 V
−40°C < TA < +125°C 4.90 V
IOUT = 10 mA 4.85 4.92 V
−40°C < TA < +125°C 4.70 V
Output Voltage Low VOL IOUT = 1 mA 8.4 20 mV
−40°C < TA < +125°C 40 mV
IOUT = 10 mA 78 145 mV
−40°C < TA < +125°C 200 mV
Output Current Isc Short circuit ±120 mA
Closed-Loop Output Impedance ZOUT At 1 MHz, AV = 1 5 Ω
POWER SUPPLY
Power Supply Rejection Ratio PSRR VSY = 2.7 V to 5.5 V 63 80 dB
Supply Current per Amplifier ISY 1.5 2.0 mA
−40°C < TA < +125°C 2.5 mA
Supply Current Shutdown Mode ISD Both amplifiers shut down, 10 nA
(AD8647 Only) VIN_SDA and VIN_SDB = 0 V
−40°C < TA < +125°C 1 μA
SHUTDOWN INPUTS (AD8647)
Logic High Voltage (Enabled) VINH −40°C < TA < +125°C +2.0 V
Logic Low Voltage (Power-Down) VINL −40°C < TA < +125°C +0.8 V
Logic Input Current (Per Pin) IIN −40°C < TA < +125°C 1 μA
Output Pin Leakage Current −40°C < TA < +125°C (shutdown active) 1 nA
DYNAMIC PERFORMANCE
Slew Rate SR RL = 2 kΩ 11 V/μs
Gain Bandwidth Product GBP 24 MHz
Phase Margin Øm 74 Degrees
Settling Time ts To 0.1% 0.5 μs
Amplifier Turn-On Time (AD8647) ton 25°C, AV = 1, RL = 1 kΩ (see Figure 44) 1 μs
Amplifier Turn-Off Time (AD8647) toff 25°C, AV = 1, RL = 1 kΩ (see Figure 45) 1 μs
Rev. F | Page 3 of 18
AD8646/AD8647/AD8648 Data Sheet
Parameter Symbol Conditions Min Typ Max Unit
NOISE PERFORMANCE
Peak-to-Peak Noise en p-p 0.1 Hz to 10 Hz 2.3 μV
Voltage Noise Density en f = 1 kHz 8 nV/√Hz
f = 10 kHz 6 nV/√Hz
Channel Separation CS f = 10 kHz −115 dB
f = 100 kHz −110 dB
Total Harmonic Distortion Plus Noise THD + N V p-p = 0.1 V, RL = 600 Ω, f = 25 kHz, TA = 25°C
AV = +1 0.010 %
AV = −10 0.021 %
Rev. F | Page 4 of 18
Data Sheet AD8646/AD8647/AD8648
VSY = 2.7 V, VCM = VSY/2, TA = +25oC, unless otherwise noted.
Table 2.
Parameter Symbol Conditions Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage VOS VCM = 0 V to 2.7 V 0.6 2.5 mV
−40°C < TA < +125°C 3.2 mV
Offset Voltage Drift ΔVOS/ΔT −40°C < TA < +125°C 1.8 7.0 μV/°C
Input Bias Current IB 0.2 1 pA
−40°C < TA < +85°C 50 pA
−40°C < TA < +125°C 550 pA
Input Offset Current IOS 0.1 0.5 pA
−40°C < TA < +85°C 50 pA
−40°C < TA < +125°C 250 pA
Input Voltage Range VCM 0 2.7 V
Common-Mode Rejection Ratio CMRR VCM = 0 V to 2.7 V 62 79 dB
Large Signal Voltage Gain AVO RL = 2 kΩ, VO = 0.5 V to 2.2 V 95 102 dB
Input Capacitance
Differential CDIFF 2.5 pF
Common Mode CCM 7.8 pF
OUTPUT CHARACTERISTICS
Output Voltage High VOH IOUT = 1 mA 2.65 2.68 V
−40°C < TA < +125°C 2.60 V
Output Voltage Low VOL IOUT = 1 mA 11 25 mV
−40°C < TA < +125°C 30 mV
Output Current Isc Short circuit ±63 mA
Closed-Loop Output Impedance ZOUT At 1 MHz, AV = 1 5 Ω
POWER SUPPLY
Power Supply Rejection Ratio PSRR VSY = 2.7 V to 5.5 V 63 80 dB
Supply Current per Amplifier ISY 1.6 2.0 mA
−40°C < TA < +125°C 2.5 mA
Supply Current Shutdown Mode ISD Both amplifiers shut down, 10 nA
(AD8647 Only) VIN_SDA and VIN_SDB = 0 V
−40°C < TA < +125°C 1 µA
SHUTDOWN INPUTS (AD8647)
Logic High Voltage (Enabled) VINH −40°C < TA < +125°C +2.0 V
Logic Low Voltage (Power-Down) VINL −40°C < TA < +125°C +0.8 V
Logic Input Current (Per Pin) IIN −40°C < TA < +125°C 1 µA
Output Pin Leakage Current −40°C < TA < +125°C (shutdown active) 1 nA
DYNAMIC PERFORMANCE
Slew Rate SR RL = 2 kΩ 11 V/μs
Gain Bandwidth Product GBP 24 MHz
Phase Margin Øm 53 Degrees
Settling Time ts To 0.1% 0.3 μs
Amplifier Turn-On Time (AD8647) ton 25°C, AV = 1, RL = 1 kΩ (see Figure 41) 1.2 μs
Amplifier Turn-Off Time (AD8647) toff 25°C, AV = 1, RL = 1 kΩ (see Figure 42) 1 μs
NOISE PERFORMANCE
Peak-to-Peak Noise en p-p 0.1 Hz to 10 Hz 2.3 μV
Voltage Noise Density en f = 1 kHz 8 nV/√Hz
f = 10 kHz 6 nV/√Hz
Channel Separation CS f = 10 kHz −115 dB
f = 100 kHz −110 dB
Rev. F | Page 5 of 18
AD8646/AD8647/AD8648 Data Sheet
Rev. F | Page 6 of 18
Data Sheet AD8646/AD8647/AD8648
NUMBER OF AMPLIFIERS
140
200
120
150 100
80
100
60
40
50
20
0 0
06527-004
06527-007
–2.0 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 –2.0 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0
VOS (mV) VOS (mV)
Figure 4. Input Offset Voltage Distribution Figure 7. Input Offset Voltage Distribution
35 35
VSY = 2.7V VSY = 5V
–40°C < TA < +125°C –40°C < TA < +125°C
30 30
NUMBER OF AMPLIFIERS
25 NUMBER OF AMPLIFIERS 25
20 20
15 15
10 10
5 5
0 0
06527-005
06527-008
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8
TCVOS (µV/°C) TCVOS (µV/°C)
Figure 5. VOS Drift (TCVOS) Distribution Figure 8. VOS Drift (TCVOS) Distribution
2500 2500
VSY = 2.7V VSY = 5V
2000 TA = 25°C 2000 TA = 25°C
1500 1500
INPUT OFFSET VOLTAGE (µV)
INPUT OFFSET VOLTAGE (µV)
1000 1000
500 500
0 0
–500 –500
–1000 –1000
–1500 –1500
–2000 –2000
06527-009
–2500 –2500
0 1 2 3 4 5
06527-006
Figure 6. Input Offset Voltage vs. Input Common-Mode Voltage Figure 9. Input Offset Voltage vs. Input Common-Mode Voltage
Rev. F | Page 7 of 18
AD8646/AD8647/AD8648 Data Sheet
10000 10000
VSY = 2.7V VSY = 5V
TA = 25°C TA = 25°C
OUTPUT SATURATION VOLTAGE (mV)
100 100
10 10
VOL
VSY – VOH
1 1
VOL
0.1 0.1
06527-010
06527-013
0.001 0.01 0.1 1 10 100 0.001 0.01 0.1 1 10 100 1000
LOAD CURRENT (mA) LOAD CURRENT (mA)
Figure 10. Output Saturation Voltage vs. Load Current Figure 13. Output Saturation Voltage vs. Load Current
25 120
VSY = 2.7V VSY = 5V
IL = 1mA
VSY – VOH = 10mA
OUTPUT SATURATION VOLTAGE (mV)
VSY – VOH 80
15 VOL = 10mA
60
10
VOL
40
5
20
VSY – VOH = 1mA
VOL = 1mA
0 0
06527-011
06527-014
–40 –25 –10 5 20 35 50 65 80 95 110 125 –40 –25 –10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C) TEMPERATURE (°C)
Figure 11. Output Saturation Voltage vs. Temperature Figure 14. Output Saturation Voltage vs. Temperature
300 300
VSY = 2.7V VSY = 5V
TA = 125°C TA = 125°C
250 250
INPUT BIAS CURRENT (pA)
200 200
150 150
100 100
50 50
0 0
06527-012
06527-015
0.50 0.75 1.00 1.25 1.50 1.75 2.00 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
COMMON-MODE VOLTAGE (V) COMMON-MODE VOLTAGE (V)
Figure 12. Input Bias Current vs. Common-Mode Voltage Figure 15. Input Bias Current vs. Common-Mode Voltage
Rev. F | Page 8 of 18
Data Sheet AD8646/AD8647/AD8648
80 0 80 0
VSY = 2.7V VSY = 5V
RL = 1kΩ RL = 1kΩ
PHASE
40 90 40 90
ФM = 52° 20 135
20 135 ФM = 74°
GAIN
0 180 0 180
06527-016
06527-019
10k 100k 1M 10M 100M 10k 100k 1M 10M 100M
FREQUENCY (Hz) FREQUENCY (Hz)
Figure 16. Open-Loop Gain and Phase vs. Frequency Figure 19. Open-Loop Gain and Phase vs. Frequency
60 60
VSY = 2.7V VSY = 5V
TA = 25°C TA = 25°C
AV = 100 AV = 100
40 40
CLOSED-LOOP GAIN (dB)
AV = 1 AV = 1
0 0
–20 –20
–40 –40
–60 –60
06527-017
06527-020
1k 10k 100k 1M 10M 100M 1k 10k 100k 1M 10M 100M
FREQUENCY (Hz) FREQUENCY (Hz)
Figure 17. Closed-Loop Gain vs. Frequency Figure 20. Closed-Loop Gain vs. Frequency
250 120
VSY = 2.7V VSY = 5V
TA = 25°C TA = 25°C
100
200
AV = 1
AV = 1 80
150
ZOUT (Ω)
ZOUT (Ω)
60 AV = 10
100 AV = 100
AV = 10
40
AV = 100
50
20
0 0
06527-018
06527-021
1 10 100 1,000 10,000 100,000 1,000,000 1 10 100 1,000 10,000 100,000 1,000,000
FREQUENCY (kHz) FREQUENCY (kHz)
Figure 18. ZOUT vs. Frequency Figure 21. ZOUT vs. Frequency
Rev. F | Page 9 of 18
AD8646/AD8647/AD8648 Data Sheet
100 100
VSY = 2.7V VSY = 5V
TA = 25°C TA = 25°C
80 80
60 60
CMRR (dB)
CMRR (dB)
40 40
20 20
0 0
06527-025
06527-022
1k 10k 100k 1M 10M 100M 1k 10k 100k 1M 10M 100M
FREQUENCY (Hz) FREQUENCY (Hz)
Figure 22. CMRR vs. Frequency Figure 25. CMRR vs. Frequency
100 100
VSY = 2.7V PSRR+ VSY = 5V
PSRR+ TA = 25°C TA = 25°C
80 80
PSRR–
60 PSRR– 60
PSRR (dB)
PSRR (dB)
40 40
20 20
0 0
06527-026
06527-023
Figure 23. PSRR vs. Frequency Figure 26. PSRR vs. Frequency
60 70
VSY = ±1.35V VSY = 5V
TA = 25°C RL = 10kΩ
60 TA = 25°C
50
–OS
50
40 +OS
OVERSHOOT (%)
OVERSHOOT (%)
40
30 OS+
30 OS–
20
20
10
10
0 0
06527-027
06527-024
Figure 24. Overshoot vs. Load Capacitance Figure 27. Overshoot vs. Load Capacitance
Rev. F | Page 10 of 20
Data Sheet AD8646/AD8647/AD8648
VSY = 2.7V, VCM = 1.35V, VIN = 100mV p-p, VSY = 5V, VCM = 2.5V, VIN = 100mV p-p,
TA = 25°C, RL = 10kΩ, CL = 100pF TA = 25°C, RL = 10kΩ, CL = 100pF
(50mV/DIV)
(50mV/DIV)
06527-028
06527-031
(200ns/DIV) (200ns/DIV)
Figure 28. Small-Signal Transient Response Figure 31. Small-Signal Transient Response
(2V/DIV)
(2V/DIV)
06527-029
06527-032
(200ns/DIV) (200ns/DIV)
Figure 29. Large-Signal Transient Response Figure 32. Large-Signal Transient Response
0.08 0.08
VSY = ±2.5V VSY = ±2.5V
RL = 600Ω RL = 600Ω
0.07 0.07
AV = 1 AV = –10
TA = 25°C TA = 25°C
0.06 0.06
0.05 0.05
THD + N (%)
THD + N (%)
0.04 0.04
0.03 0.03
0.02 0.02
0.01 0.01
0 0
06527-030
06527-033
Figure 30. THD + Noise vs. Frequency Figure 33. THD + Noise vs. Frequency
Rev. F | Page 11 of 18
AD8646/AD8647/AD8648 Data Sheet
1
VSY = 2.7V TO 5V
TA = 25°C
0.1
VOLTAGE (1µV/DIV)
THD + N (%)
0.01
0.001 VSY = 5V
AV = 1
BW = 30kHz
RL = 100kΩ
f = 1kHz
06527037
0.0001
06527-034
TIME (1s/DIV) 0.001 0.01 0.1 1
OUTPUT AMPLITUDE (V rms)
Figure 34. 0.1 Hz to 10 Hz Voltage Noise Figure 37. THD + Noise vs. Output Amplitude
1000 1000
VSY = 2.7V TO 5V VSY = 5V
TA = 25°C
VOLTAGE NOISE DENSITY (nV/√Hz)
100
INPUT BIAS CURRENT (pA)
100
10
10
1
1 0.1
06527-038
06527-035
Figure 35. Voltage Noise Density vs. Frequency Figure 38. Input Bias Current vs. Temperature
2.5 5.0
TA = 25°C VSY = 5V
4.5 VIN = 4.9V
SUPPLY CURRENT PER AMPLIFIER (mA)
AV = 1
2.0 4.0 RL = 10kΩ
TA = 25°C
OUTPUT SWING (V p-p)
3.5
1.5 3.0
2.5
1.0 2.0
1.5
0.5 1.0
0.5
0 0
06527-036
06527-039
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 100 1,000 10,000
SUPPLY VOLTAGE (V) FREQUENCY (kHz)
Figure 36. Supply Current per Amplifier vs. Supply Voltage Figure 39. Maximum Output Swing vs. Frequency
Rev. F | Page 12 of 18
Data Sheet AD8646/AD8647/AD8648
4.0 0
VSY = 5V R1
VOUT = VSY/2 CS (dB) = 20 log (VOUT/100 = VIN)
RL = 2kΩ 20Ω
SUPPLY CURRENT PER AMPLIFIER (mA)
3.5 AV = –100
–20 V+ V–
TA = 25°C R2
3 U2 6 200Ω
1.0
VIN = 2V p-p
–100
0.5
VIN = 0.5V p-p
0 –120
06527-042
06527-040
–40 –20 0 20 40 60 80 100 120 1k 10k 100k
TEMPERATURE (°C) FREQUENCY (Hz)
Figure 40. Supply Current per Amplifier vs. Temperature Figure 43. Channel Separation
VSY = 5V
SHUTDOWN PIN SHUTDOWN PIN
RL = 1kΩ
AV = 1
VSY = 2.7V TA = 25°C
RL = 1kΩ
AV = 1
VOLTAGE (1V/DIV)
VOLTAGE (1V/DIV)
TA = 25°C
AMPLIFIER OUTPUT
AMPLIFIER OUTPUT
06527-043
06527-045
SHUTDOWN PIN
VOLTAGE (1V/DIV)
VOLTAGE (1V/DIV)
SHUTDOWN PIN
06527-044
Rev. F | Page 13 of 18
AD8646/AD8647/AD8648 Data Sheet
100 100
VSY = 2.7V VSY = 5V
10 10
ISY (nA)
ISY (nA)
1 1
0.1 0.1
0.01 0.01
06527-048
06527-047
–40 –25 –10 5 20 35 50 65 80 95 110 125 –40 –25 –10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C) TEMPERATURE (°C)
Figure 46. Supply Current with Op-Amp Shutdown vs. Temperature Figure 47. Supply Current with Op-Amp Shutdown vs. Temperature
Rev. F | Page 14 of 18
Data Sheet AD8646/AD8647/AD8648
THEORY OF OPERATION
POWER-DOWN OPERATION
The shutdown function of the AD8647 is referenced to the 2V
negative supply voltage of the operational amplifier. A logic
1V
level high (> 2.0 V) enables the device, while a logic level low
(< 0.8 V) disables the device and places the output in a high 0V
impedance condition. Several outputs can be wire-OR’ed, thus
eliminating a multiplexer. The logic input is a high impedance
CMOS input. If dual or split supplies are used, the logic signals
must be properly referred to the negative supply voltage.
5V
MULTIPLEXING OPERATION
0V
Because each op amp has a separate logic input enable pin, the
06527-050
outputs can be connected together if it can be guaranteed that
TIME (200µs/DIV)
only one op amp is active at any time. By connecting the op amps
Figure 49. Switching Waveforms
as shown in Figure 48, a multiplexer can be eliminated. With
the reasonably short turn-on and turn-off times, low frequency
signal paths can be smoothly selected. The turn-off time is 80
slightly faster than the turn-on time so, even when using 70
sections from two different packages, the overlap is less than
60
300 nanoseconds.
SUPPLY CURRENT (µA)
50
1/2
8 AD8647 40
9
7 30
6
5kHz
20
5V VSY = 5V
10
1/2 VSY = 2.7V
AD8647 0
2 10
1 –10
06527-051
3 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
5
4 VIN_SDA AND VIN_SDB (V)
13kHz
Figure 50. Supply Current Shutdown Mode, AD8647
06527-049
1 2
2kHz
Rev. F | Page 15 of 18
AD8646/AD8647/AD8648 Data Sheet
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8 5
4.00 (0.1574) 6.20 (0.2441)
3.80 (0.1497) 1 5.80 (0.2284)
4
012407-A
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
3.20
3.00
2.80
8 5 5.15
3.20 4.90
3.00 4.65
2.80 1
4
PIN 1
IDENTIFIER
0.65 BSC
Rev. F | Page 16 of 18
Data Sheet AD8646/AD8647/AD8648
3.10
3.00
2.90
10 6 5.15
3.10 4.90
3.00 4.65
2.90 1
5
PIN 1
IDENTIFIER
0.50 BSC
091709-A
COMPLIANT TO JEDEC STANDARDS MO-187-BA
5.10
5.00
4.90
14 8
4.50
4.40 6.40
BSC
4.30
1
7
PIN 1
0.65 BSC
1.05
1.00 1.20
MAX 0.20
0.80 0.09 0.75
0.15 8° 0.60
SEATING 0°
0.05 0.30 PLANE 0.45
COPLANARITY 0.19
0.10
061908-A
Rev. F | Page 17 of 18
AD8646/AD8647/AD8648 Data Sheet
8.75 (0.3445)
8.55 (0.3366)
14 8
4.00 (0.1575) 6.20 (0.2441)
1
3.80 (0.1496) 7 5.80 (0.2283)
060606-A
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
ORDERING GUIDE
Model1, 2 Temperature Range Package Description Package Option Branding
AD8646ARZ −40°C to +125°C 8-Lead SOIC_N R-8
AD8646ARZ-REEL −40°C to +125°C 8-Lead SOIC_N R-8
AD8646ARZ-REEL7 −40°C to +125°C 8-Lead SOIC_N R-8
AD8646ARMZ −40°C to +125°C 8-Lead MSOP RM-8 A1V
AD8646ARMZ-REEL −40°C to +125°C 8-Lead MSOP RM-8 A1V
AD8646WARZ-RL −40°C to +125°C 8-Lead SOIC_N R-8
AD8646WARZ-R7 −40°C to +125°C 8-Lead SOIC_N R-8
AD8646WARMZ-RL −40°C to +125°C 8-Lead MSOP RM-8 A1V
AD8646WARMZ-R7 −40°C to +125°C 8-Lead MSOP RM-8 A1V
AD8647ARMZ −40°C to +125°C 10-Lead MSOP RM-10 A1W
AD8647ARMZ-REEL −40°C to +125°C 10-Lead MSOP RM-10 A1W
AD8648ARZ −40°C to +125°C 14-Lead SOIC_N R-14
AD8648ARZ-REEL −40°C to +125°C 14-Lead SOIC_N R-14
AD8648ARZ-REEL7 −40°C to +125°C 14-Lead SOIC_N R-14
AD8648ARUZ −40°C to +125°C 14-Lead TSSOP RU-14
AD8648ARUZ-REEL −40°C to +125°C 14-Lead TSSOP RU-14
AD8648WARUZ −40°C to +125°C 14-Lead TSSOP RU-14
AD8648WARUZ-RL −40°C to +125°C 14-Lead TSSOP RU-14
1
Z = RoHS Compliant Part.
2
W = Qualified for Automotive Applications.
Rev. F | Page 18 of 18