Professional Documents
Culture Documents
Series
Pre-compensated Load Sensing Sectional Valves
DPC Series
Additional information
This catalogue shows the product in the most standard configurations.
Please contact Sales Dpt. for more detailed information or special request.
WARNING!
All specifications of this catalogue refer to the standard product at this date.
Walvoil, oriented to a continuous improvement, reserves the right to
discontinue, modify or revise the specifications, without notice.
2 D1WWED02E
DPC Series General information
____________________________________________________________________________________________
The DPC Series
The DPC Series is a family of open/closed center pre-pressure compensated sectional valves designed specifically for Mobile
Applications. The DPC series provides exceptional controllability, efficiency and flexibility for applications requiring up to 240 l/min
(63.4 US gpm) flow rate. DPC Series is available in two different sizes: DPC130 (DPC130X) and DPC200.
_________________________________________________________________________
The Load Sensing technology
Thanks to the use of specially designed pumps and control valves, the Load Sensing principle can be considered the most com-
prehensive means of creating a flexible hydraulic circuit that can adapt to the various operating conditions demanded by users.
The main feature of this principle is that the flow rate to the user is proportional to the spool position under any operating condi-
tion, regardless of the resistance encountered by the user (pressure) and the number of levers activated (exceeding the pump’s
total flow rate, a condition here in after defined as saturation, is the only limitation).
Therefore, with the LS systems, there is a specific correspondence between the position of the control lever and the movement
speed of the user, cylinder or hydraulic motor. This feature is particularly useful in the hydraulic handling machine sector (ex-
cavators, cranes, loaders, agricultural and forestry machinery) in which each movement phase has specific sequences that the
operator must control by using memorised movements.
Real energy savings can be obtained above all when the DPC directional valves operate together with variable displacement Load
Sensing pumps. When the DPC valve is utilised with fixed displacement pumps, the previously mentioned movement indepen-
dence and repeatability features are guaranteed, but energy savings will be limited.
For special options please contact Sales Dept.
_________________________________________________________________________________________
The ATEX version
The DPC130X is the DPC Series new valve built according to the ATEX directive for safe use in classified areas, with inflammable
and potentially explosive materials.
Hydraulic features and performance remain the same of the DPC130 standard valve.
For more informations see code D1WWED03E catalogue.
D1WWED02E 3
General information DPC Series
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s - 46 cSt viscosity at 40°C -
104°F temperature.
DPC130 DPC200
on inlet port with compensator @ stand-by (margin 150 l/min - 39.6 US gpm 260 l/min - 68.7 US gpm
pressure) @ 9 bar - 131 ps @ 11.5 bar - 167 ps
Nominal flow rating on working ports with compensator (Qin/Qut>10%) 100 l/min - 26.4 US gpm 200 l/min - 52.8 US gpm
(open center circuit) @ stand-by (margin pressure) @ 7 bar - 102 ps @ 7 bar - 102 ps
on working ports without compensator (Qin/Qut>10%) 130 l/min - 34.3US gpm 240 l/min - 63.4 US gpm
@ stand-by (margin pressure) @ 9 bar - 131 ps @ 11.5 bar - 167 ps
P inlet port 315 bar (2) - 4500 psi (2) 350 bar (1) - 5100 psi (1)
Max. pressure
A and B working ports 315 bar ( ) - 4500 psi ( )
2 2
420 bar (1) - 6100 psi (1)
on T outlet port 25 bar - 363 psi 25 bar - 363 psi
Back pressure (max.)
on L drain port 2.5 bar - 36 psi 2.5 bar - 36 psi
Standard internal leakage ∆p=100 bar - 1450 psi 16 cm /min - 0.98 in /min
3 3
20 cm3/min - 1.22 in3/min
A(B)->T with port valves, ∆p=100 bar - 1450 psi 21 cm3/min - 1.28 in3/min 25 cm3/min - 1.53 in3/min
Fluid Mineral oil
with seals NBR (BUNA-N) from -20°C to 80°C - from -4°F to 176°F
Fluid temperature range
with seals FPM (VITON) from -20°C to 100°C - from -4°F to 212°F
operating range from 15 to 75 mm2/s - from 15 to 75 cSt
Viscosity min. 12 mm2/s - 12 cSt
max. 400 mm2/s - 400 cSt
Contamination level max. -/18/15 - ISO 4406 - NAS 1638 class 9
with mechanical devices from -40°C to 60°C - from -40°F to 140°F
Environmental temperature
with hydraulic/pneumatic devices from -30°C to 60°C - from -22°F to 140°F
for working conditions
with electric/electrohydraulic devices from -20°C to 50°C - from -4°F to 122°F
NOTES: (1) According to NFPA T 2.6.1., fatigue rating verified for 1 million cycles on 6 sample valves with test Pressure = 1.23 x Max.
pressure indicated - (2) According to NFPA T 2.6.1., fatigue rating verified for 1 million cycles on 8 sample valves with test Pressure =
1.104 x Max. pressure indicated.
4 D1WWED02E
DPC Series General information
_________________________________________________________________________________________
Standard threads
REFERENCE STANDARD
BSP UN-UNF NPTF Flange connection
THREAD ISO 228/1 ISO 263 ISO 6162
ANSI B1.20.3
ACCORDING TO BS 2779 ANSI B1.1 unified SAE J518
NOTES (3): Standard pressure series - (4): For pressure up to 350 bar (5100 psi)
DPC130 DPC200
PORTS
BSP UN-UNF BSP UN-UNF Flange connection (bolts threading)
THREADING
ISO 6162-1 type 1 SAE J518 code 61
P inlet G 3/4 1 1/16-12 (SAE 12) G1 1 5/16-12 (SAE 16) DN 19 (M10) 3/4 (3/8-16 UNC)
A and B ports G 1/2 7/8-14 (SAE10) G1 1 5/16-12 (SAE 16) DN 19 (M10) 3/4 (3/8-16 UNC)
T outlet G 3/4 1 1/16-12 (SAE 12) G 1-1/4 1 5/8-12 (SAE 20) DN 25 (M10) 1 (3/8-16 UNC)
LS Load Sensing G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
V1 pilot G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
depends on inlet section type:
V2 pilot M14x1.5 (5)
see pages from 14 to 17 (5) see BSP threading see UN-UNF threading
L drain G 1/4 7/16-20 (SAE 4) G 1/4 7/16-20 (SAE 4)
M pressure gauge G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
Hydraulic control ports G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
NOTES ( ): ATTENTION! V2 pilot port requires dedicated joints; please see Inlet section pages.
5
D1WWED02E 5
Index DPC Series
Contents
DPC130
Dimensional data and performance. . . . . . . . . . . . . . . . . . page 8
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Complete section ordering codes. . . . . . . . . . . . . . . . . . . . . . . 10
• Inlet section
Inlet section part ordering codes . . . . . . . . . . . . . . . page 12
Dimensions and hydraulic circuit. . . . . . . . . . . . . . . . . . . . 14
L.S. pressure relief valves . . . . . . . . . . . . . . . . . . . . . . . . 21
Solenoid operated L.S. unloading valve. . . . . . . . . . . . . . . 21
Solenoid operated Shut-Off pilot valve. . . . . . . . . . . . . . . 21
• Working section
Working section part ordering codes. . . . . . . . . . . . . page 22
Dimensions and hydraulic circuit. . . . . . . . . . . . . . . . . . . . 26
Standard spools and spools for independent drain . . . . . . . 28
Pressure control spools. . . . . . . . . . . . . . . . . . . . . . . . . . 34
"A" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 38
Electrohydraulic controls. . . . . . . . . . . . . . . . . . . . . . . . . 40
"B" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 45
Port valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
L.S. port relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
On/off solenoid operated L.S. unloading valve . . . . . . . . . . 47
Proportional solenoid operated L.S. unloading valve . . . . . . 48
• Outlet section
Outlet section part ordering codes . . . . . . . . . . . . . . page 49
Dimensions and hydraulic circuit. . . . . . . . . . . . . . . . . . . . 50
Drain options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
DPC200
Dimensional data and performance. . . . . . . . . . . . . . . . . page 52
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Complete section ordering codes. . . . . . . . . . . . . . . . . . . . . . . 54
• Inlet section
Inlet section part ordering codes . . . . . . . . . . . . . . . page 56
Dimensions and hydraulic circuit. . . . . . . . . . . . . . . . . . . . 58
Pressure reducing valve. . . . . . . . . . . . . . . . . . . . . . . . . . 60
Solenoid operated unloading valve . . . . . . . . . . . . . . . . . . 60
L.S. pressure relief valves . . . . . . . . . . . . . . . . . . . . . . . . 61
• Working section
Working section part ordering codes. . . . . . . . . . . . . page 62
Dimensions and hydraulic circuit. . . . . . . . . . . . . . . . . . . . 64
Spools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
"A" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 68
Electrohydraulic controls. . . . . . . . . . . . . . . . . . . . . . . . . 70
"B" side spool control kit. . . . . . . . . . . . . . . . . . . . . . . . . 74
Port valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
L.S. port relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
• Outlet section
Outlet section part ordering codes . . . . . . . . . . . . . . page 77
Dimensions and hydraulic circuit. . . . . . . . . . . . . . . . . . . . 78
Drain options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6 D1WWED02E
DPC Series Index
Special configurations
Connection between DPC Series valves. . . . . . . . . . . page 80
Accessories
Coils and connectors. . . . . . . . . . . . . . . . . . . . . . . . page 82
Installation
Main rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 85
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 86
D1WWED02E 7
DPC130 DPC Series
81 48 50 53
170.5 3.19 2.01 1.97 2.09
6.73 37.1 16 16 10
54.5 1.46 0.63 0.63 0.39
2.15
Ø 8.5
2.76
70
Ø 0.33
5
0.31
0.197
0.19
4.7
8
0.43
11
P
33.5
1.32
L A2 A1
43.5
2.01
4.57
116
10.98
3.94
100
279
1.30
33
45.5
1.79
LS B2 B1
33.5
1.32
0.35
9
0.31
8
130.4 8 E
5.13 0.31
152 F
5.98
20 300
200
E F Weight 10
Type 100
mm in mm in Kg lb
0 0
DPC130/1 184 7.24 200 7.87 12.4 27.3 0 30 60 90 120 150 (l/min)
DPC130/2 232 9.13 248 9.76 19.4 42.8 Flow
34.3 US gpm
130 l/min
30
8th section 400
Pressure
0 0
0 30 60 90 120 150 (l/min)
Flow
8 D1WWED02E
DPC Series DPC130
__________________________________________________________________________________________
Hydraulic circuit
B2 A2 B1 A1
P T
V2
L
V1
LS
LSAB LSAB
Open center circuit and one-side proportional electrohydraulic control with lever,
with unloader valve and pressure reducing valve, port valve arrangement on all
ports, LSAB port, internal pilot and external drain
B2 A2 B1 A1
P T
V2
L
V1
LS
LSAB LSAB
Closed center circuit and one-side proportional electrohydraulic control
with lever, with unloader valve and pressure reducing valve, antishock and
anticavitation valves on all ports, L.S. relief valves on 2nd section, LSAB ports,
internal pilot and external drain
D1WWED02E 9
DPC130 DPC Series
DPC130/2/BR21-S220-ELP/C10-1S8EZ3L1/C22-1S8EZ3L1.UTUTSTST/RF30-......-12VDC-<SB20-CVN>
7A
7A
7A 2
7A
DPC130/2/BRF21-S250/C10-1S8EZ3L1/C22-1S8EZ3L1.UTUTSTST/RF30-......-12VDC-<SB20-CVN>
1 2 2 3 4 5 6
7B
7B
Tie rod tightening
wrench 13 - 30 Nm (22 lbft)
7B
2
7B
2
10 D1WWED02E
DPC Series DPC130
____________________________________________________________________
Complete section ordering codes
D1WWED02E 11
DPC130 DPC Series
DPC130 / BR - S200 - DSK -...... DPC130 / BN21 - S220 - ...... DPC130 / BR21 - S220 - ELP - ...... - 12VDC
1 2 1 5 1 2 5 1 2 3 5 6A
2 2 2
1
1 1
3
6A
DPC130 / BRS21 - S220 - ELP - ...... - 12VDC DPC130 / BRSOG21(SF) - S220 - ELN3 - ...... - 12VDC
1 2 3 5 6A 1 2 4 5 6B
2 6B
3 1
6A
1 2
1 2 5
Circuit conversion kit
1.1
2
1 7
12 D1WWED02E
DPC Series DPC130
____________________________________________________________________
Inlet section part ordering codes
1 Inlet section kit* page 14 3 Solenoid operated L.S. unloading valve page 21
TYPE: DPC130/BR-DSK CODE: 5FIA631350 BER type coil is required: see chapter 6
DESCRIPTION: With compensator, pressure reducing valve and TYPE CODE DESCRIPTION
selector for open/closed center circuit ELN 0EC08002031 Without emergency override
Closed Center circuit ELP 0EC08002033 With push-button emergency override
TYPE: DPC130/BN21 CODE: 5FIA631302 ELT 0EC08002035 With “twist & push” emergency override
DESCRIPTION: With secondary pressure control system, without ELV 0EC08002034 With screw type emergency override
pressure reducing valve LT XTAP510320 Unloading valve blanking plug
TYPE: DPC130/BR21 CODE: 5FIA631300
DESCRIPTION: As previous one, with pressure reducing valve 4 Solenoid operated Shut-off pilot valve page 21
TYPE: DPC130/BRSOG21(SF) CODE: 5FIA631374G
DESCRIPTION: Shut-Off type, with secondary pressure control BT type coil is required: see chapter 6
system and pressure reducing valve (L.S. joint without filter) TYPE CODE DESCRIPTION
TYPE: DPC130/BRS21 CODE: 5FIA631360 ELN3 0EJ08002035 Without emergency override
DESCRIPTION: Copy-Spool type, with secondary pressure control ELT3 0EJ08002042 With screw emergency override
system and pressure reducing valve
TYPE: DPC130/BRF21 CODE: 5FIA630306 5 Section threading
DESCRIPTION: With pressure reducing valve Only specify if it is different from BSP standard (see page 5).
Open Center circuit
TYPE: DPC130/BN11 CODE: 5FIA631303
6A Coil
DESCRIPTION: With compensator, without pressure reducing valve
TYPE: DPC130/BR11 CODE: 5FIA631301 TYPE CODE DESCRIPTION
DESCRIPTION: With compensator and pressure reducing valve 12VDC 4SLE001200A 12VDC BER type coil, ISO4400 connector
TYPE: DPC130/BRS11 CODE: 5FIA631361 (for unloading valve)
DESCRIPTION: Copy-Spool type, with compensator and pressure For complete available coil list see page 82.
reducing valve
6B Coil
1.1 Parts page 20 TYPE CODE DESCRIPTION
They are included in BRF inlet section ordering code 12VDC 4SL3000120 12VDC BT type coil, ISO4400 connector
CODE DESCRIPTION (for Shut-Off pilot valve)
X219740035 Pressure reducing valve For complete available coil list see page 82.
XTAP418350 Pressure reducing valve blanking plug
7 Circuit conversion kit
2 L.S. pressure relief valves page 21 CODE DESCRIPTION
Standard setting is referred to 10 l/min (2.6 US gpm flow). For BR and BN inlet sections
TYPE INITIAL CODE DESCRIPTION 5KIT130300 Circuit conversion kit: from Open Center to Closed Center
LSD S XCAR126215 With blind nut, 5KIT130310 Circuit conversion kit: from Closed Center to Open Center
range 40-180 bar (580-2600 psi), For BRS inlet inlet section
std. setting 90 bar (1300 psi) 5KIT130301 Circuit conversion kit: from Open Center to Closed Center
XCAR126213 As previous one, 5KIT130320 Circuit conversion kit: from Closed Center to Open Center
range 180-350 bar (2600-5100 psi),
std. setting 180 bar (2600 psi)
LSH H XCAR126216 With locked arrangement,
range 40-180 bar (580-2600 psi),
std. setting 90 bar (1300 psi)
XCAR126217 As previous one,
range 180-350 bar (2600-5100 psi),
std. setting 180 bar (2600 psi)
LSZ Z 5CAR126221 With anti-tamper cap,
range 40-180 bar (580-2600 psi),
std. setting 90 bar (1300 psi)
5CAR126219 As previous one,
range 180-350 bar (2600-5100 psi),
std. setting 180 bar (2600 psi)
ST ST 5KIT126210 Relief valve blanking plug
D1WWED02E 13
DPC130 DPC Series
Inlet section________________________________________________________________________________________________
K
X
V1
W K
V2
DSK valve:
to screw for Open Center
Y
to unscrew for Closed Center
33.5
1.32
Reduced pressure
DSK valve Dim. A G 30
400
function mm in T
Open Center 24.5 0.96 P 20 300
1.42
36
0 0
LS 0 3 6 9 12 15 (l/min)
X
Flow
14 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
21.5
0.85 Y
X
V1 P T
W
31.5
1.24
X V2
max.164.4
max. 6.47
V2
Z
130.4
5.13
LS
3.31
84
V1
54.5
2.15
0.39
10
28 2 7 115.5
1.10 0.079 0.276 4.55
129.5
5.10
LS
0.39
10
2.76
70
T
P
2.09
53
LS
0.67
17
36.5 43.5 11
1.44 1.71 0.43
100 8
3.94 0.31
D1WWED02E 15
DPC130 DPC Series
Inlet section________________________________________________________________________________________________
21.5
0.85 K
X
V1
P T
31.5
1.24
K W
V2 Y
max.164.4
max. 6.47
LS V2
130.4
5.13
Z
3.31
84
54.5
2.15
0.39
10
V1
33.5
1.32
28 X 7 115.5
1.10 0.276 4.55
129.5
5.10
max. 213.5
max. 8.41
LS
0.39
10
T
2.76
70
P
1.42
36
2.09
53
LS
0.67
36.5 43.5 11
17
30
please see page 21.
400
Auxiliary port specification
20 300 V1 = G1/4 pilot pressure port (Pmax = 30 bar - 435 psi) for
200 hydraulic pilot control valve feeding (P⇒OUT)
10 V2 = M14x1.5 pilot pressure port for:
100 - electrohydraulic control optional feeding (Pmax = 315 bar
0
4600 psi) (P⇒IN); G1/4 joint is required, code 5GIU519611
0
0 3 6 9 12 15 (l/min) - pressure gauge connection; G1/4 joint is required, code
Flow 5GIU620330.
16 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
26
1.02 Y
X Auxiliary port specification
V1 W V1 = G1/4 pilot pressure port for elec- P T
trohydraulic control feeding (Pmax = 30
X V2 bar - 435 psi) (P⇒IN)
V2 = G1/4 pressure gauge connection V2
Z
Wrenches and tightening torque
X = allen wrench 6 - 24 Nm (17.7 lbft)
Y = allen wrench 10 - 24 Nm (17.7 lbft) V1
X
Z = wrench 19 - 24 Nm (17.7 lbft)
W = wrench 34 - 42 Nm (31 lbft)
NOTE: for relief valve wrench and torque
please see page 21
T
P LS
LS
26
1.02 K
X
V1 P T
K W
V2 Y
V2
Z
X V1
T
P LS
Wrenches and tightening torque
E = allen wrench 4
F = wrench 17 - 24 Nm (17.7 lbft)
G = wrench 24 - 42 Nm (31 lbft) LS
K = allen wrench 5 - 24 Nm (17.7 lbft)
X = allen wrench 6 - 24 Nm (17.7 lbft)
Auxiliary port specification
Y = allen wrench 10 - 24 Nm (17.7 lbft)
V1 = G1/4 pilot pressure port (Pmax = 30 bar - 435 psi) for hydraulic pilot control valve feeding (P⇒OUT)
Z = wrench 19 - 24 Nm (17.7 lbft)
V2 = M14x1.5 pilot pressure port for:
W = wrench 34 - 42 Nm (31 lbft)
- electrohydraulic control optional feeding (Pmax = 315 bar - 4600 psi) (P⇒IN); G1/4 joint is
NOTE: for relief valve and solenoid valve
required, code 5GIU519611
wrench and torque please see page 21.
- pressure gauge connection; G1/4 joint is required, code 5GIU620330.
D1WWED02E 17
DPC130 DPC Series
Inlet section________________________________________________________________________________________________
Solenoid operated
Shut-Off pilot valve
21.5
19.5
0.85
0.77
max. 219
max. 8.62
X
Y
Z
130.4
5.13
W
110.8
4.36
96.7
3.81
0.39
1.77
10
45
X
27.5 7 115.5 50.8
1.08 0.28 4.55 2.00
17 70 127
0.67 2.76 5.00
9
0.354
T
P
17.5
0.69
X
64.8
2.55
K
43.5
V1
1.71
1.10
28
LS
2.8
0.110
2 45.5 45 8
0.079 1.79 1.77 0.31
100
3.94
T P
Auxiliary port specification
M = G1/4 pressure gauge connection
V1 = G1/4 pilot pressure port (Pmax = 30 bar - 435 psi)
for hydraulic pilot control valve feeding (P⇒OUT)
LS
18 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
21.5 12
0.85 H 0.47
X
V1 LS
LS
31.5
1.24
K V2 W
max.164.4
Y Z
max. 6.47
130.4
5.13
I
107.2
4.22
3.31
84
0.39
10
31.5
1.24
variable-zone H X
28 12 115.5 38 17
dumper standard
1.10 setting 0.47 4.55 1.50 0.67
53 144 70
2.09 5.67 2.76
max. 213.5
max. 8.41
16.5 43.5 11
0.65 1.71 0.43
0.39
10
T
P
2.09
53
LS
H K
7.5 100 8
0.295 3.94 0.315
P T P T
Auxiliary port specification
V1 = G1/4 pilot pressure port (Pmax = 30 bar - 435 psi) for hydrau-
lic pilot control valve feeding (P⇒OUT) V2 V2
V2 = M14x1.5 pilot pressure port for:
- electrohydraulic controls optional feeding (Pmax = 315 bar - 4600
psi) (P⇒IN); G1/4 joint is required, code 5GIU519611
- pressure gauge connection; G1/4 joint is required, code V1 V1
5GIU620330.
D1WWED02E 19
DPC130 DPC Series
Inlet section________________________________________________________________________________________________
5.83
148
132.5
5.22
1.42
36
Z
LS
1.81
46
1.50
34.5
1.36
38
46.8 24.2 14 17
X
0.39
1.84 0.95
10
0.55 0.67
100 38
3.94 1.50
6 30.5
0.236 1.20
H
LS Auxiliary port specification
M = G1/4 pressure gauge connection
1.42
40
30 450
20 300
10 150
0 0
0 70 140 210 280 350 (bar)
Pressure
LS
20 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
0 10 20 30 (US gpm)
Y Y X K 400
max. setting(2) (psi)
(bar)
X X 5000
300
J J medium range setting(2) 4000
J J
Pressure
200 max. setting(1) min. and std. setting(2) 3000
2000
Valve Dim. B 100
std. setting(1)
ELN
Valve Dim. C
type mm in G F ELP ELV ELT LT
ELN 65.5 2.58
1
ELP 88.5 3.48
2
ELV 88.5 3.48 E
C 1 1 1 1
ELT 91 3.58
2 2 2 2
ELN3 ELT3
Legenda
G
ELN3: without emergency
ELT3: screw emergency override
A
D1WWED02E 21
DPC130 DPC Series
1 2 3 3 1 2 3 4 5 6 7
Lever position: please see page 45
6 10
5
3
D10 section
3 Elemento C22
3
3
1 2
1
2
3 4
3
4
DPC130/C26-1PC2D 8IML1.U100U320S250S250-...
1A 2B
valve on A port - 1
valve on B port - 2
valve on A and B ports - 3
A port B port A port B port
C26 section 1A 2A 3 4 5 6 7A 8 3
Lever position: see page 45 9
6 10
1A 5
2B
3 C27 section
C27S section
9
1A
7A 3
2A
7A
9
7B
3
22 D1WWED02E
DPC Series DPC130
________________________________________________________________
Working section part ordering codes
1 Working section kit* page 26 1A Special working section kit* page 31
Without compensator Sections with compensator, arranged for L.S. relief with independent
TYPE: DPC130/D10 CODE: 5EL6312310 drain and pressure control spools
DESCRIPTION: Without valve arrangement Dedicated spools are requested (see chapter 2A and 2B)
TYPE: DPC130/D20 CODE: 5EL6312320 TYPE: DPC130/C26 CODE: 5EL6323000
DESCRIPTION: With port valve arrangement DESCRIPTION: Arranged for port valves and two L.S. relief with
TYPE: DPC130/D21 CODE: 5EL6312321 independent drain
DESCRIPTION: Arranged for port valves and one L.S. relief valve TYPE: DPC130/C27 CODE: 5EL6323100
TYPE: DPC130/G20 CODE: 5EL6315320 DESCRIPTION: As previous one, with lower block for L.S. signal on/off
DESCRIPTION: For floating circuit, with port valve arrangement unloader valve arrangement4
TYPE: DPC130/DM23 CODE: 5EL6312350 TYPE: DPC130/C27SA CODE: 5EL6323100A
DESCRIPTION: For regenerative circuit, arranged for port valves and DESCRIPTION: As type C26, with lower block for proportional
one L.S. relief valve unloader valve arrangement on port A L.S. signal
Without compensator, with check valve TYPE: DPC130/C27SB CODE: 5ELXXXXXXX
TYPE: DPC130/CV10 CODE: 5EL6311310B DESCRIPTION: As type C26, with lower block for proportional
DESCRIPTION: Without valve arrangement unloader valve arrangement on port B L.S. signal
TYPE: DPC130/CV13 CODE: 5EL6311313A
DESCRIPTION: As previous one with additional L.S. upper port 2 Standard spool page 34
TYPE: DPC130/CV20 CODE: 5EL6311320B
Flow is referred to 7 bar (102 psi) stand-by (margin pressure)
DESCRIPTION: With port valve arrangement
TYPE CODE DESCRIPTION
TYPE: DPC130/CV21 CODE: 5EL6311321D
Double acting with A and B closed in neutral position
DESCRIPTION: Arranged for port valves and one L.S. relief valve
1C 3CU4010005 5 l/min (1.3 US gpm) flow
TYPE: DPC130/CV23 CODE: 5EL6311323A
1D 3CU4010010 10 l/min (2.6 US gpm) flow
DESCRIPTION: As previous one with additional L.S. upper port
1V 3CU4010025 25 l/min (6.6 US gpm) flow
TYPE: DPC130/CV22 CODE: 5EL6311322A
1Q 3CU4010040 40 l/min (10.6 US gpm) flow
DESCRIPTION: Arranged for port valves and two L.S. relief valves
1S 3CU4010060 60 l/min (15.9 US gpm) flow
TYPE: DPC130/FV20 CODE: 5EL6314320B
1N 3CU4010080 80 l/min (21.1 US gpm) flow
DESCRIPTION: For floating circuit, with port valve arrangement
1PN 3CU4010103 100 l/min (26.4 US gpm) flow
TYPE: DPC130/CVM23 CODE: 5EL6311325B
Double acting with A and B to tank in neutral position
DESCRIPTION: For regenerative circuit, arranged for port valves and
2C 3CU4024005 5 l/min (1.3 US gpm) flow
one L.S. relief valve
2D 3CU4024010 10 l/min (2.6 US gpm) flow
With compensator
2V 3CU4024025 25 l/min (6.6 US gpm) flow
TYPE: DPC130/C10 CODE: 5EL6311310
2Q 3CU4024040 40 l/min (10.6 US gpm) flow
DESCRIPTION: Without valve arrangement
2S 3CU4024060 60 l/min (15.9 US gpm) flow
TYPE: DPC130/C13 CODE: 5EL6311313
2N 3CU4024080 80 l/min (21.1 US gpm) flow
DESCRIPTION: As previous one with additional L.S. upper port
2P 3CU4024100 100 l/min (26.4 US gpm) flow
TYPE: DPC130/C20 CODE: 5EL6311320
Double acting with A and B partially to tank in neutral position
DESCRIPTION: With port valve arrangement
2HC 3CU4025006 5 l/min (1.3 US gpm) flow
TYPE: DPC130/C24 CODE: 5EL6311324A
2HD 3CU4025011 10 l/min (2.6 US gpm) flow
DESCRIPTION: As previous one with additional L.S. upper port
2HV 3CU4025034 25 l/min (6.6 US gpm) flow
TYPE: DPC130/C21 CODE: 5EL6311321.
2HQ 3CU4025047 40 l/min (10.6 US gpm) flow
DESCRIPTION: Arranged for port valves and one L.S. relief valve
2HS 3CU4025061 60 l/min (15.9 US gpm) flow
TYPE: DPC130/C23 CODE: 5EL6311323.
2HN 3CU4025081 80 l/min (21.1 US gpm) flow
DESCRIPTION: As previous one with additional L.S. upper port
2HP 3CU4025102 100 l/min (26.4 US gpm) flow
TYPE: DPC130/C22 CODE: 5EL6311322.
Single acting on A, B plugged: G1/2 plug is required
DESCRIPTION: Arranged for port valves and two L.S. relief valves
3Q 3CU4031040 40 l/min (10.6 US gpm) flow
TYPE: DPC130/F10 CODE: 5EL6314310
3S 3CU4031060 60 l/min (15.9 US gpm) flow
DESCRIPTION: For floating circuit, without port valve arrangement
3N 3CU4031080 80 l/min (21.1 US gpm) flow
TYPE: DPC130/F20 CODE: 5EL6314320.
3PN 3CU4031100 100 l/min (26.4 US gpm) flow
DESCRIPTION: For floating circuit, with port valve arrangement
Double acting with A and B closed in neutral position, 4 positions,
TYPE: DPC130/CM23 CODE: 5EL6311325A
floating in 4th pos. with spool out: F, G or FV type section and 13
DESCRIPTION: For regenerative circuit, arranged for port valves and
type positioner or control are required
one L.S. relief valve
5Q 3CU4041040 40 l/min (10.6 US gpm) flow
5S 3CU4041060 60 l/min (15.9 US gpm) flow
5N 3CU4041080 80 l/min (21.1 US gpm) flow
Double acting with A and B closed in neutral position, 3 positions,
regenerative in 3rd pos. with spool out: CM, DM or CVM type section,
and 8 type dedicated control, with reduced stroke, are required
8F 3CU4033070 50-70 l/min flow (port A-port B)
(13.2-18.5 US gpm)
Double acting with A and B closed in neutral position, 4 positions,
regenerative in 4th pos. with spool out: CM, DM or CVM type section
and dedicated 13 type positioner or control are required
8Y 3CU4044070 70 l/min (18.5 US gpm) flow
D1WWED02E 23
DPC130 DPC Series
24 D1WWED02E
DPC Series DPC130
________________________________________________________________
Working section part ordering codes
6 L.S. port relief valves page 46 7B Solenoid operated L.S. unloading valve page 48
Standard setting is referred to 10 l/min (2.6 US gpm) flow. Proportional type for C27SA - C27SB sections
TYPE ID CODE DESCRIPTION Valvole ordering code is inclusive of coil
LSD S XCAR126215 With blind nut, range 40-180 bar (580-2600 TYPE CODE DESCRIPTION
psi), standard setting 90 bar (1300 psi) MC10T/031B 0MC10002019 Range from 15 to 130 bar (217 to 1890 psi),
XCAR126213 Range 180-350 bar (2600-5100 psi), 12VDC coil, ISO4400 connector
standard setting 180 bar (2600 psi) MC10T/032B 0MC10002020 Range from 15 to 170 bar (217 to 2470 psi),
LSH H XCAR126216 With locked arrangement, range 40-180 bar 12VDC coil, ISO4400 connector
(580-2600 psi), std setting 90 bar (1300 psi) MC10T/033B 0MC10002021 Range from 15 to 210 bar (217 to 3050 psi),
XCAR126217 Range 180-350 bar (2600-5100 psi), 12VDC coil, ISO4400 connector
standard setting 180 bar (2600 psi) MC10T/034B 0MC10002031 Range from 15 to 280 bar (217 to 4050 psi),
LSZ Z 5CAR126221 With anti-tamper cap, range 40-180 bar 12VDC coil, Deutsch DT04 connector
(580-2600 psi), std setting 90 bar (1300 psi)
5CAR126219 Range 180-350 bar (2600-5100 psi), 8 Section threading
standard setting 180 bar (2600 psi)
Only specify if it is different from BSP standard (see page 5).
ST ST 5KIT126210 Relief valve blanking plug
9 Coil
7A Solenoid operated L.S. unloading valve page 47
TYPE CODE DESCRIPTION
On/off type for C27 section
12VDC 4SLE001200A 12VDC BER type coil, ISO4400 connector
BER coil is required: see chapter 9 (for unloading valve)
TYPE CODE DESCRIPTION For complete available coil list please see page 82.
LST3T XTAP510320 Valve blanking plug
Normally open circuit (NO)
10 Plug for single acting spool*
LSTN(NA) 0EC08002031 Without manual emergency
LSTV(NA) 0EC08002034 With screw type emergency CODE DESCRIPTION
LSTP(NA) 0EC08002033 With push-button emergency 3XTAP727180 G1/2 plug
LSTT(NA) 0EC08002035 With “push & twist” emergency
Normally closed circuit (NC)
LSTN(NC) 0EC08002032 Without manual emergency
LSTV(NC) 0EC08002037 With screw type emergency
LSTP(NC) 0EC08002036 With pull-button emergency
LSTT(NC) 0EC08002038 With “pull & twist” emergency
D1WWED02E 25
DPC130 DPC Series
Working section___________________________________________________________________________________________
Without compensator
0.43
LSAB
11
B
1.413
35.9
allen wrench 6 69.5
2.74
A
24 Nm (17.7 lbft)
0.476
12.1
D21 type
130.4
B
0.157
1.42
36
33 41.5
4
1.89
16
48
A
16
8
116
0.315
4.57
D10 type D20 type D21 type G20 type DM23 type
without port valve with port valve as D20, arrangement as D20, for as D21, for
arrangement arrangement for one L.S. relief valve floating circuit regenrative circuit
B A B A B A B A B A
26 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Z X
5.31
135
12
0.47
39.5
1.56
11.8
0.46
LSAB'
A
X
B
B A LSAB’ B A
LSAB LSAB
D1WWED02E 27
DPC130 DPC Series
Working section___________________________________________________________________________________________
A A
CV22 type
arrangement for port valves and L.S. CV23 type
relief valves arrangement for port valves and one
L.S. valve on B ports L.S. relief valve, with upper L.S. port
86 15 L.S. valve on A and B ports
3.39 0.59 B port valve B port valve
B B
0.47
12
LSAB'
1.413
35.9
1.42
36
A A
79 18.5 A port valve
0.476
L.S. valve on
12.1
3.11 0.73
A ports
A port valve
28 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
With compensator
The unlisted dimensions are the same of previous sections.
LSAB
B
LSAB'
A
Z X
X
C20 type
with port valves arrangement
B port valve
B
A
39.5
1.56
A port valve
C21 type
0.157
4
A
40 116
1.57 4.57
A port valve
Wrenches and tightening torque
X = allen wrench 6 - 24 Nm (17.7 lbft)
Z = wrench 19 - 50 Nm (36.9 lbft)
B A LSAB’ B A B A B A
D1WWED02E 29
DPC130 DPC Series
Working section___________________________________________________________________________________________
With compensator
The unlisted dimensions are the same of previous sections.
C22 type
arrangement for port valves and L.S.
relief valves
L.S. valve on B ports B port valve
C21 type C22 type C23 type C24 type
B B A LSAB’ B A LSAB’ B A
B A
C23 type
arrangement for port valves and one L.S.
relief valve, with upper L.S. port
L.S. valve on A and B ports B port valve
B
LSAB'
A
A port valve
C24 type
with port valves arrangement
LSAB LSAB LSAB LSAB
and upper L.S. port
B port valve
B
LSAB' F10 type F20 type CM23 type
A as C10, as C20, as C21,
for floating circuit for floating circuit for regenrative circuit
A port valve B A B A B A
30 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
With compensator
Special sections with L.S.signal independent drain; to be use with dedicated spools or pressure control spools.
The unlisted dimensions are the same of previous sections.
C26 type C27 type
arrangement for port valves and L.S. relief valves as C26 with arrangement for L.S. signal on/off
with independent drain unloader valves
48.5
X
1.91
LSB
0.43 1.02
26
LSA
11
Z W
66.5
X
Z 2.62
0.39
10
36.5
1.44
26.5
1.04
14.5
0.57
0.157
B port valve 17 65
0.67 2.56
B
L.S. valve on A ports
B port valve
A B
B A
B A
LSB
D1WWED02E 31
DPC130 DPC Series
Working section___________________________________________________________________________________________
With compensator
Special sections with L.S.signal independent drain; to be use with dedicated spools or pressure control spools.
The unlisted dimensions are the same of previous sections.
C27A type
as C26 with proportional unloader
valve arrangement on port A L.S. signal
B A
Z
0.39
10
1.69
43
1.34
34
15.5
0.61
70 34
2.76 1.34
LSA
A
A port valve
32 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
With compensator
Special sections with L.S.signal independent drain; to be use with dedicated spools or pressure control spools.
The unlisted dimensions are the same of previous sections.
C27B type
as C26 with proportional unloader
valve arrangement on port B L.S. signal
B A
Z
0.39
10
1.69
43
1.34
34
15.5
0.61
54 34
2.13 1.34
Valvola bocca B
B
LSB
A
Valvola Valvola L.S.
bocca A bocca B
D1WWED02E 33
DPC130 DPC Series
Working section___________________________________________________________________________________________
Standard spools
1 0 2 1 0 2 1 0 2 1 0 2
P P P P
T T T T
A B A B A B A B
8F type spool
5 type spool regenerative in 8Y type spool
floating in 4th position (pos.3) 2nd position (pos.1) regenerative in 4th position (pos.3)
3 1 0 2 1 0 2 3 1 0 2
P P P
T T T
A B A B A B
1 0 2 1 0 2
P P
T T
A B A B
34 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Metering curves
Compensated working section - 3 position spools
Qin = 150 l/min (39.6 US gpm)
217.5 200 160 120 80 72.5 0 72.5 80 120 160 200 217.5
(psi)
-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in)
150
(US gpm)
(l/min)
120 32
P P
N N
24
Port flow
90
S S
60 16
Q Q
V V
30 8
D D
C C
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
position 2 Spool stroke position 1
Pilot pressure
(bar)
With 8IM
15.0 12.5 10.0 7.5 5.0 0 5.0 7.5 10.0 12.5 15.0
control kit
Current (mA@12VDC)
1000 900 800 700 600 500 0 500 600 700 800 900 1000
With 8EZ3 and
8EZ3T control kit (mA@24VDC)
500 450 400 350 300 250 0 250 300 350 400 450 500
D1WWED02E 35
DPC130 DPC Series
Working section___________________________________________________________________________________________
Features
The pressure control spools are designed in such a way that the stroke controls the pump pressure.
The spool must be actuated until the pump pressure slightly exceeds the load pressure before the work function is applied. If
the spool is kept in this position, the pump pressure will remain constant, even in case of load pressure changes, thus ensuring
system stability.
Use of the pressure control spool, means as well:
• both the fluid flow and the dead band depend on the load
• a flow proportional to the ΔP between the L.S. signal and the load on the port, which does not remain constant will be dispensed.
• the pressure drop through the main spool is due to vary (energy consumption).
Because of these factors, the pressure control spools must only be used when load instability issues are ascertained and in those
applications where constant pressure is required such as Drilling Machines.
Application
The pressure control spools should only be used when load stability problems exist, as could occur during lifting/descent and
rotation (with cylinders) operations of a crane.
For the lifting/descent operation a “single” type pressure control spool is best used. This type of spool is designed for normal flow
control on the port used for lifting, and for pressure control on the port connected to the pilot signal of the counterbalance valve.
An independent load lifting movement is thus obtained, as well as a dropping function which is stable but dependent on the load.
In the rotation function, the load pressure is usually constant, irrespective of the fact whether the crane is loaded or not, and a
spool must therefore be used with pressure control function on both ports A and B.
In both cases a working section with pressure compensator is required (C26 or C27 types).
Always make a point of using the L.S. pressure relief valves, which not only ensure individual pressure limitation but also allow
adjusting the max flow to ports.
Any anti-shock valves must be set to 20% higher than the setting values of the L.S. pressure relief valves.
Limitation
The use of the pressure control spools therefore allows limiting oscillations and obtaining smooth and precise control of the
function with the following limitations:
• the “non-adjustment” stroke of the spool (dead band) will depend on load conditions
• the working section of the control valve will lose the "load independent" characteristic
• pump pressure could exceed load pressure.
36 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Flow on ports
1 0 2 1 0 2 90 24
P P 60 16
30 8
T T T T
0 0
0 70 140 210 280 350 (bar)
Pressure
A B A B
Flow vs Pressure curve
Size D (25 l/min - 6.6 US gpm) spool
Spool stroke Spool stroke 0 1000 2000 3000 4000 5000 (psi)
position 1: + 7 mm (+ 0.28 in) position 1: + 7 mm (+ 0.28 in) 150
(l/min) Example 1 (US gpm)
position 2: - 7 mm (- 0.28 in) position 2: - 7 mm (- 0.28 in)
120 32
Flow on ports
Pp
90 24
Pressure control on B port
60 16
1PC2(D,V,Q) type spool 2HPC2(D,V,Q) type spool
30 8
A, B closed in neutral A, B partially to tank in
position neutral position 0 0
0 70 140 210 280 350 (bar)
Pressure
1 0 2 1 0 2
Flow vs Pressure curve
P P
Size Q (40/lmin - 10.6 US gpm) spool
0 1000 2000 3000 4000 5000 (psi)
T T T T 150
(l/min) Example 2 (US gpm)
120 32
Flow on ports
90 24
A B A B
60 P2 16
Sizing
Example 1: how to determine the flow to ports
To know the flow to ports of a spool of known size, you need to know the seting pressure of the valve on the L.S. signal as well
as the operating pressure.
As shown in the example, the spool is size D (25 l/min in flow control), the valve on the LS signal is calibrated at 210 bar - 3050
psi (zero flow to port with such load). Following the third parabola of the operating curve, it can be seen that with a load of 150
bar - 2200 psi we have 55 l/min - 14.5 US gpm on port.
Example 2: how to determine the spool size
It is necessary to know the flow to port (e.g., 55 l/min - 14.5 US gpm), the setting pressure of the pressure relief valve on the L.S.
signal (180 bar - 2600 psi) and the operating pressure (150 bar - 2200 psi).
Tracing the parabolas parallel to those entered in the characteristic curve graphs, in the spool type Q we obtain a curve that
crosses the required points: 55 l/min at 150 bar - 14.5 US gpm and 0 l/min - US gpm at 180 bar - 2600 psi.
D1WWED02E 37
DPC130 DPC Series
Working section___________________________________________________________________________________________
Y Z
X
1 0 2
71.5
2.81
113.5 Features
4.47
Friction load adjusting. . . . . : 20-150 N (4.5-34 lbf)
Friction load std. setting . . . : 100 N (22.5 lbf)
Center tap (more than load).: 100 N (22.5 lbf)
16
71.5
2.81
60
Spring A type
8
30
0 0
0 1 2 3 4 5 6 7 pos.1 (mm)
Wrenches and tightening torque
X = allen wrench 5 - 9.8 Nm (7.2 lbf) 0 -1 -2 -3 -4 -5 -6 -7 pos.2 (mm)
Stroke
38 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
3 1 0 2
71.5
2.81
Features
Y Detent force (±10%). . . . . . : 310 N (70 lbf)
Release force (±10%). . . . . : 110 N (24.7 lbf)
45.5
1.79 Wrenches and tightening torque
X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Y = wrench 13 - 24 Nm ( 17.7 lbf)
VA VB
27
VA
1 0 2
X
71.5
71.5
2.81
2.81
Features
Max. pressure. . . . . . . . . . . . . : 50 bar (725 psi)
24
0.94 Wrenches and tightening torque
48 X = allen wrench 5 - 9.8 Nm (7.2 lbf)
1.89 Y = wrench 13 - 24 Nm ( 17.7 lbf)
Suggested pressure
Stroke vs. Pressure diagram control curve: 020 type
-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in) 0 0.05 0.10 0.15 0.20 0.25 0.3 (in)
20 (psi) 40 (psi)
35 bar (508 psi)
(bar) 250 (bar) 500
15 30
Pilot pressure
200 400
Pressure
10 150 20 300
(0.30 in)
10 4.3 bar
(0.29 in)
7.6 mm
D1WWED02E 39
DPC130 DPC Series
Working section___________________________________________________________________________________________
Electric specifications
Dither frequency high frequency 150 Hz (200 mA) 100 Hz (200 mA) 150 Hz (200 mA) 150 Hz (200 mA)
Hydraulic specifications
Max. back pressure on drain 2.5 bar (36 psi) 2.5 bar (36 psi)
Note (1) For the calculation rules please see "Appendix A" on page 86.
Listed electrohydraulic controls require CED400W electronic control unit; for information please contact Sales Department.
40 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
700 350
500 /250 mA
350 175
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
position 2 Stroke position 1
800 / 400 mA
700 350
560 /280 mA
350 175
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
position 2 Stroke position 1
D1WWED02E 41
DPC130 DPC Series
Working section___________________________________________________________________________________________
SPSL sensor
The SPSL position sensor converts the spool movements into a voltage linear signal.
Output voltage
Mechanical life 3x106 operation tolerance
Connector type DT04-4P Deutsch 3
SPSD sensor
The SPSD position sensor converts the spool movements into an electric digital signal.
operation tolerance
operation tolerance
42 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Electrohydraulic controls
844 800
33.23 31.50
3 2 1 Y
8EZ3 - 8EZ4
8EZ4D - 8EZ3CR types
coil 2
1 0 2
174.5
174.5
6.87
X
169.5
6.87
coil 1
6.67
13EZ3 - 13EZ4
71.5
2.81
(8Y)13EZ3 types
coil 2
coil 1
3 1 0 2
4 1
3
2 1 3 2
GND
Magnet is to be assembled
Connectors with this side (printed side)
Wire colour Function
pin facing the section side
without O-ring seating
1 blue common (-)
2 red Coil 2 - B port
3 green Coil 1 - A port
4 - Plugged
D1WWED02E 43
DPC130 DPC Series
Working section___________________________________________________________________________________________
Electrohydraulic controls
Control Types
1 : With AMP JPT connector - AMP JPT mating connector, code: 5CON003
2 : With Deutsch DT04 connector - Deutsch DT06-2S mating connector code: 5CON140031
2
1
8EZ3T - 8EZ34T types
EVB
EVA
1 0 2
Z
EVA
A port
EVB
B port
181.5
7.15
X 13EZ3T type
170.5
6.71
EVB
EVA
3 1 0 2
71.5
2.81
2
1 8EZ3TSPSD - 8EZ3T4SPSD types
CANbus interface
EVA
1 0 2 EVB
Z
#
G
EVA
A port
EVB
B port
K J
181.5
7.15
170.5
6.71
1 0 2
71.5
2.81
X EVA EVB
U
G
44 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Aluminium lever box; L type Aluminium lever box with Aluminium lever box,
anti-tamper caps; LZ type without lever; LN type
3 1 0 2 3 1 0 2 3 1 0 2
21
42 45° 6 0
°3
1.65 0' 99.5
X 3.92 X
16
30
°3
°
0'
1
3
71.5
2.81
1.85
1.55
47
39
W Z Y W Z Y
X Cap code:
87 4COP116420
3.43
B B
B
20.4
0.80
R
M8 Dimensions are the Dimensions are the
same as L type same as L type
Wrenches and tightening torque
X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Y = allen wrench 3
Z = wrench 10 - 9.8 Nm (7.2 lbf)
W = allen wrench 4 - 6.6 Nm (4.9 lbf)
R = wrench 8
3 1 0 2
60°
3
Lever with standard
assembling
48
1.89
15° 0 23.4 23.4
0.92 0.92
60
W Z Y
°
X
2
B
60°
D1WWED02E 45
DPC130 DPC Series
Working section___________________________________________________________________________________________
Port valves
D
0 5 10 15 20 25 (US gpm)
35.9
0 5 10 15 20 25 (US gpm)
A 400 40 (psi)
340 bar (4950 psi) (psi)
(bar) (bar)
5000 500
79 18.5 (3900 psi)
0.476
300 30
12.1
270 bar
3.11 0.73 4000 400
Pressure
Pressure
210 bar (3050 psi)
200 3000 20 300
(2050 psi) e
140 bar yp
Valve Dim. D 2000 Ct
200
80 bar (1150 psi)
type mm in 100 10
typ
e
25 bar (360 psi) 1000 U 100
U 10.5 0.41
0 0 0 0
C 10.5 0.41 0 20 40 60 80 100 (l/min) 0 20 40 60 80 100 (l/min)
UT 7.5 0.30 Flow Flow
W cap part K
Y
Y Y 4COP116420
X X X J
J J
5.55
141
A 400 (psi)
ST: valve blanking plug (bar) max. setting(2)
5000
86 15
Wrenches and tightening torques
300
3.39 0.59 X = wrench 13 - 24 Nm (17.7 lbf) medium range setting(2) 4000
Y = wrench 10 - 9.8 Nm (7.2 lbf)
Pressure
LSH 17 0.67 0 0
0 20 40 60 80 100 (l/min)
LSZ 34 1.34 Flow
46 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
LSTN(NA) LSTN(NC)
G F G F
2 2
1 1
1 1
2 2
LSTP(NA) LSTP(NC)
2 2
1 1
1 1
C
2 2
LSTV(NA) LSTV(NC)
2 2
1 1
D E
1 1
Dimensions
2 2
Valve
C D E
type
mm in mm in mm in LSTT(NA) LSTT(NC)
Features Legenda
Max. flow. . . . . . . . . . . . . . . . : 40 l/min (10.6 US gpm) LSTN(NA): without emergency
Max. pressure. . . . . . . . . . . . . : 380 bar (5500 psi) LSTP(NA): push button emergency override
Internal leakage. . . . . . . . . . . : 0.25 cm3/min @ 210 bar LSTV(NA): screw emergency override
(0.015 in3/min @ 3050 psi) LSTT(NA): “push&twist” emergency override
For coil features and BER type coil options please see page 83. LSTN(NC): without emergency
LSTP(NC): pull button emergency override
LSTV(NC): screw emergency override
LSTT(NC): “pull&twist” emergency override
LST3T: valve blanking plug (both valve seats)
Wrenches and tightening torques
F = wrench 24 - 30 Nm (22 lbf)
G = manual tightening
E = wrench 10 - 24 Nm (17.7 lbf)
D1WWED02E 47
DPC130 DPC Series
Working section___________________________________________________________________________________________
D G
H
96.5 96.5
3.80 3.80
For coil features and BQP19 type coil options please see page 83.
48 D1WWED02E
DPC Series DPC130
__________________________________________________________________
Outlet section part ordering codes
DPC130/RD 3 1 - ......
3 1 2
1 2 3 4
2
D1WWED02E 49
DPC130 DPC Series
Outlet section______________________________________________________________________________________________
Y
L
Y
T1 T1
0.366
9.3
1.89
48
1.46
37
9
0.354 P1 P1
42 86 RF30 type L
1.65 1.42
115.5
Without ports, external drain
L L
4.55
12.7 Y L
0.50
1.26
32
L
20.1
0.80
0.21.7
5.5
100 8
3.94 0.315
Note: Do not plug LS1 port (in case it is not
used it has to be connected to tank). LS1
Drain options
F
Option 33
external drain for
Dim. F electrohydraulic controls
Option
mm in
N
Wrenches and tightening torque
1 3.5 0.138
M = allen wrench 5 - 24 Nm (17.7 lbf)
2 3.5 0.138 N = wrench 19 - 24 Nm (17.7 lbf)
3 19 0.75
50 D1WWED02E
DPC Series DPC130
D1WWED02E 51
DPC200 DPC Series
3.23
82
64.5
2.54
V1
L
36.5
1.44
0.98
25
V2 A2 A1
P
28.25
28.25
1.112
1.112
398.3
15.68
8.15
207
2.68
5.28
70.5
134
2.78
68
T
M12
37.75
1.486
35.25
1.388
B2 B1
19.25
0.758
36.5
1.44
6 36.5 21.5
0.236 1.44 0.85
93
3.66
189.5 F
7.46
E F Weight E F Weight
TYPE TYPE
mm in mm in Kg lb mm in mm in Kg lb
DPC200/1 124 4.88 220 8.66 39.5 87.1 DPC200/6 389 15.31 485 19.09 111 245
PA1501568/004
16802..........
Ref.............
DPC200/2 177 6.97 273 10.75 53.8 117 DPC200/7 442 17.40 538 21.18 125 276
DPC200/2
DPC200/3 230 9.06 326 12.83 68.1 150 DPC200/8 495 19.49 591 23.27 140 308
DPC200/4 283 11.14 379 14.92 82.4 182 DPC200/9 548 21.57 644 25.35 154 339
DPC200/5 336 13.23 432 17.01 96.7 213 DPC200/10 601 23.66 697 27.44 168 371
product code
P⇒T Pressure drop inlet compensator A(B)⇒T pressure drop
customer reference
(margin pressure) (standard spool @ max.stroke)
product name
production allotment 0 10 20 30 40 50 60 (US gpm) 0 10 20 30 40 50 60 (US gpm)
20 60
(psi) (psi)
(bar) (bar)
250 750
15 45
200 600
Pressure
10th section
Pressure
10 150 30 450
5th section
100 300
5 15
50 150
1st section
0 0 0 0
0 40 80 120 160 200 240 (l/min) 0 40 80 120 160 200 240 (l/min)
Flow Flow
52 D1WWED02E
DPC Series DPC200
__________________________________________________________________________________________
Hydraulic circuit
B2 A2 B1 A1
P T
M
V2
L
V1
VB2 VB1
LS
VA2 VA1
Open center circuit and proportional hydraulic control with lever, with unloader
valve and port valve arrangement
B2 A2 B1 A1
P T
M
V2
L
V1
EVB2
EVB1
LS
EVA2 EVA1
D1WWED02E 53
DPC200 DPC Series
2 7A
3
1
7A
1 2 3 4 5 6
7B
3
1
7B
54 D1WWED02E
DPC Series DPC200
____________________________________________________________________
Complete section ordering codes
D1WWED02E 55
DPC200 DPC Series
1 2 3 5 6 4 7 8 1 2 3 5 6 7 8
5 5
1 1
6 6
8 8
DPC200/BRF2 - 3 0 (H220\ELP)-......-12VDC
1 2 3 5 6 7 8
8
1.1
9
56 D1WWED02E
DPC Series DPC200
____________________________________________________________________
Inlet section part ordering codes
1 Inlet section body kit* page 58 5 L.S. pressure relief valve page 61
Open Center circuit Standard setting is referred to 10 l/min (2.6 US gpm) flow.
TYPE: DPC200/BR1-1 CODE: 5FIA620302 TYPE ID CODE DESCRIPTION
DESCRIPTION: With compensator and pressure reducing valve, P-T-LS LSD S XCAR126215 With blind nut, range 40-180 bar (580-2600
ports (LS plugged), arranged for unloader valve psi), standard setting 90 bar (1300 psi)
TYPE: DPC200/BR1-1-FS3-M(BSP) CODE: 5FIA620303 XCAR126213 Range 180-350 bar (2600-5100 psi),
DESCRIPTION: As previous one, with ISO 6162-1 type 1 flange standard setting 180 bar (2600 psi)
connection LSH H XCAR126216 With locked arrangement, range 40-180 bar
TYPE: DPC200/BN1-1 CODE: 5FIA620309 (580-2600 psi), std setting 90 bar (1300 psi)
DESCRIPTION: With compensator, P-T-LS ports (LS plugged), arranged XCAR126217 Range 180-350 bar (2600-5100 psi),
for pressure reducing valve (seat plugged) and unloader valve standard setting 180 bar (2600 psi)
Closed Center circuit LSZ Z 5CAR126221 With anti-tamper cap, range 40-180 bar
TYPE: DPC200/BR2-1 CODE: 5FIA620304 (580-2600 psi), std setting 90 bar (1300 psi)
DESCRIPTION: With compensator and pressure reducing valve, P-T-LS 5CAR126219 Range 180-350 bar (2600-5100 psi),
ports, arranged for unloader valve standard setting 180 bar (2600 psi)
TYPE: DPC200/BR2-1-FS3-M(BSP) CODE: 5FIA620305 ST ST 5KIT126210 Relief valve blanking plug
DESCRIPTION: As previous one, with ISO 6162-1 type 1 flange
connection 6 Solenoid operated L.S. unloading valve page 60
TYPE: DPC200/BN2-1 CODE: 5FIA620300
DESCRIPTION: With compensator, P-T-LS ports, arranged for pressure BER type coil to be used: please see chapter 8
reducing valve (seat plugged) and unloader valve TYPE CODE DESCRIPTION
TYPE: DPC200/BRF2-3 CODE: 5FIA620306 ELN 0EC08002031 Without emergency override
DESCRIPTION: Without compensator, with pressure reducing valve, ELP 0EC08002033 With push-button emergency override
P-T-LS ports, arranged for unloader valve ELT 0EC08002035 With “twist & push” emergency override
TYPE: DPC200/BRF2-3-FS3-M(BSP) CODE: 5FIA620307 ELV 0EC08002034 With screw type emergency override
DESCRIPTION: As previous one, with ISO 6162-1 type 1 flange LT XTAP510320 Unloading valve blanking plug
connection
TYPE: DPC200/BNF2-3 CODE: 5FIA620310 7 Section threading
DESCRIPTION: Without compensator, with P-T-LS ports, arranged for Specify threading only if it is different from BSP standard.
pressure reducing valve (seat plugged) and unloader valve For section with ISO 6162-1 type 1 flange connection digit: FS3-
M(BSP).
1.1 Particolari page 60
They are included in BRF inlet section ordering code 8 Coil
CODE DESCRIPTION TYPE CODE DESCRIPTION
4AC9539900A Pressure reducing valve, setting 32 bar (460 psi) 12VDC 4SLE001200 BER type coil, ISO4400 conn., 12VDC
3XTP3535100 Pressure reducing valve blanking plug For complete available coil list please see page 82.
4 Compensator stanb-by
Specify value only if it is different from the standard (11.5 bar - 167
psi): for Open Center sections
D1WWED02E 57
DPC200 DPC Series
Y Z
Y
max. 202
max. 7.95
6.69
170
132.5
5.22
126.5
4.98
LS
4.37
111
3.66
3.50
93
89
78.5
3.09
X
1.85
47
0.47
12
85 23.75
3.35 0.935
36.5 134
1.44 5.28 M12 nr.2 threads
Auxiliary port specification 9.75 35.25 70.5 28.25 Pressure
M = G1/4 pressure gauge connection 0.384 1.388 2.78 1.112 reducing
Y
V1 = G1/4 pilot pressure port (Pmax = valve
48.5
30 bar - 435 psi) for hydraulic pilot control
1.91
T
valve feeding (P⇒OUT) P
0.71
18
0.236
2.5
6
G1/4 joint is required, code 5GIU519611.
21.5
0.85
LS
W 207 82
8.15 3.23
max. 380
max. 14.96
M M
V2 V2
FS3-M(BSP) optional connection
35.25 70.5
V1 V1 1.39 2.78
13.1
0.52
11.1
0.44
T P
26.2
22.2
1.03
0.87
0.24
6
LS
LS 26.2 23.8
0.94 M10
1.03
nr. 4+4 threads
LS 52.4 47.6
2.06 1.87
58 D1WWED02E
DPC Series DPC200
________________________________________________________________________________________________
Inlet section
R
6.34
161
152.5
6.00
4.29
109
3.23
80.5
82
3.17
64.5
2.54
2.28
58
1.85
47
34.5
1.36
7.1 4 15
0.63
0.47
12
20.1
valve
0.79
1.44 5.28
Auxiliary port specification
M = G1/4 pressure gauge connection
V1 = G1/4 pilot pressure port (Pmax = 30 bar
49.5
1.95
- 435 psi) for hydraulic pilot control valve feeding
0.23
5.9
max. 135
max. 5.31
(P⇒OUT)
18.5
0.73
11.1
0.44
15
Y
Wrenches and tightening torque LS 0.59
R = allen wrench 10 - 24 Nm (17.7 lbft) W
Y = allen wrench 6 - 24 Nm (17.7 lbft)
W = wrench 19 - 24 Nm (17.7 lbft)
NOTE: for valves wrench and torque please see 207 82
pages 60-61. 8.15 3.23
max. 323
max. 12.72
M M
0.52
26.2
1.03
V1 V1
4.29
109
22.2
0.87
38.6
1.52
11.1
0.44
LS LS
17.25 89 27.75
0.689 3.50 1.093
D1WWED02E 59
DPC200 DPC Series
Inlet section________________________________________________________________________________________________
Reduced pressure
2 3
45
F 600
F
30
400
On BR section
On BRF section 15 200
0 0
0 3 6 9 12 15 (l/min)
82 Flow
3.23
82
3.23
Features
Reduced press. range . . : from 3.5 to 35 bar
(from 50 to 500 psi)
Max. inlet pressure. . . . : 420 bar (6100 psi)
Nominal flow . . . . . . . . : 15 l/min (4 US gpm)
118.5 118.5
4.67 4.67
G F
1 1 1
On BR section On BRF section
2 2
1 1
A
2 2
C
ELV ELT
E LT
1 1
2 2
1 1
2 2
B D
60 D1WWED02E
DPC Series DPC200
________________________________________________________________________________________________
Inlet section
LSH LSD C
A
W Y
Y Y
X X
J J
B
LSZ ST
cap part
K
4COP116420
X J
D
J
Legenda
BR section BRF section
LSH: with lock arrangement Valve
LSD: with blind nut A B C D
type
LSZ: with anti-tamper cap mm in mm in mm in mm in
ST: valve blanking plug
LSD 19.5 0.77 189.5 7.46 21.5 0.85 58 2.28
Wrenches and tightening torques
X = wrench 13 - 24 Nm (17.7 lbf) LSH 15 0.59 185 7.28 16 0.63 52.5 2.07
Y = wrench 10 - 9.8 Nm (7.2 lbf) LSZ 32 1.26 202 7.95 34 1.34 70.5 2.78
W = allen wrench 3
J = wrench 7 - 24 Nm (17.7 lbf)
K = allen wrench 5 - 24 Nm (17.7 lbf)
200 max. setting (1) min. and std. setting (2) 3000
2000
std. setting(1)
100
min. setting(1) 1000
0 0
0 40 80 120 160 200 240 280 (l/min)
Flow
D1WWED02E 61
DPC200 DPC Series
1 2 3A 4 5 6 7 3
8
6
2 2
1 1 3
4
62 D1WWED02E
DPC Series DPC200
_______________________________________________________________
Working section part ordering codes
D1WWED02E 63
DPC200 DPC Series
Working section___________________________________________________________________________________________
0.47
12
(not for C10 type) Z lever side
LSA
1.14
29
lever side
LSB
135.75 71.25
5.34 2.81
6.69
170
Wrenches and tightening torques
X = allen wrench 12 - 90 Nm (66 lbf)
Y = allen wrench 17 - 90 Nm (66 lbf)
3.43
87
Y
FS3-M(BSP) optional connection
36.5
0.177
4.5
1.44 47.6
207 1.87
8.15 M10 23.8
nr. 4+4 threads 0.94 lever side
A B A B
2.09
22.2
0.87
53
26.5
1.04
26.5
1.04
11.1
0.44
64.75 68 74.25 68 74.25
2.549 2.68 2.923 2.68 2.923
L.S. valve
on B port
A B
17
0.59
15
0.37
9.5
64 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
With compensator
B A B A B A B A
B A B A B A
D1WWED02E 65
DPC200 DPC Series
Working section___________________________________________________________________________________________
Spools
2 0 1 2 0 1 2 0 1
P P P
T T T T T T
A B A B A B
Spool stroke Spool stroke Spool stroke
position 1: - 8 mm (- 0.31 in) position 1: - 8 mm (- 0.31 in) position 1: - 8 mm (- 0.31 in)
position 2: + 8 mm (+ 0.31 in) position 2: + 8 mm (+ 0.31 in) position 2: + 8 mm (+ 0.31 in)
2 0 1 2 0 1 3
P P
T T T T
A B A B
Spool stroke Spool stroke
position 1: - 8 mm (- 0.31 in) position 1: - 8 mm (- 0.31 in)
position 2: + 8 mm (+ 0.31 in) position 2: + 8 mm (+ 0.31 in)
position 3: - 13 mm (- 0.51 in)
66 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Spools
Following curves are detected with standard spools, connecting P⇒A⇒B⇒T and P⇒B⇒A⇒T ports without flow multiplication.
Customized spools with backpressure or flow multiplication may require different force, pressure and pilot current for
operation.
NOTE: for spools up to 120 l/min (31.7 US gpm), the effective flow on working ports may differ by 10% between the 1st an 10th
section.
Metering curves
Compensated working section - 3 position spools
Qin = 260 l/min (68.7 US gpm)
With 8IM 222 200 150 100 75 0 75 100 150 200 222
(psi)
control kit
-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
250
(l/min) 60
H H (US gpm)
200
G G
45
F F
Port flow
150
E -2.2 mm 2.2 mm E
D -0.087 in 0.087 in D 30
100
C C
B B 15
50
A A
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
position 1 Spool stroke position 2
Pilot pressure
(bar)
With 8IM
15.3 15.0 12.0 9.0 6.0 5.2 0 5.2 6.0 9.0 12.0 15.0 15.3
control kit
Current (mA@12VDC)
1300 1200 1000 800 650 0 650 800 1000 1200 1300
With 8EZ3T
control kit (mA@24VDC)
650 600 500 400 325 0 325 400 500 600 650
D1WWED02E 67
DPC200 DPC Series
Working section___________________________________________________________________________________________
2 0 1
17.5
0.69
X
Y
W Z
3.43
87
113.5
4.47
2 0 1
65.3 N
75 (14.7 lbf) 16
50
(±0.087 in)
43.5 N
±2.2 mm
(9.8 lbf) 8
25
3.43
87
0 0
0 1 2 3 4 5 6 7 8 pos.2 (mm)
0 -1 -2 -3 -4 -5 -6 -7 -8 pos.1 (mm)
16 Stroke
0.63
68 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
2 0 1 3
X
3.43
87
60
2.36
VB
13IM type
For floating circuit
VB VA
85.5
3.37
2 0 1 3
3.43
87
26.5
Features (all types) 1.04
53
Max. pressure. . . . . . . . . . : 50 bar (725 psi)
2.09
Wrenches and tightening torques
X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Pilot pressure
200 400
10 150 20 300
(0.30 in)
10
(0.29 in)
4.3 bar
7.6 mm
D1WWED02E 69
DPC200 DPC Series
Working section___________________________________________________________________________________________
Electrohydraulic controls
Electric specifications
12 VDC - 850 mA
Float flow control signal
24 VDC - 250 mA
Weather protection (connector) IP65 (JPT type) - IP69K (DT type) IP65 (JPT type) - IP69K (DT type)
Hydraulic specifications
Max. back pressure on drain 2.5 bar (36 psi) 2.5 bar (36 psi)
Note (1) for the calculation rules please see "Appendix A" on page 80.
Listed electrohydraulic controls require CED400W electronic unit; for information please contact Sales Department.
70 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
SPSL sensor
The SPSL position sensor converts the spool movements into a voltage linear signal.
Output voltage
Mechanical life 3x106 operation tolerance
Connector type DT04-4P Deutsch 3
SPSD sensor
The SPSD position sensor converts the spool movements into an electric digital signal.
operation tolerance
operation tolerance
D1WWED02E 71
DPC200 DPC Series
Working section___________________________________________________________________________________________
Electrohydraulic controls
2
1
Y
8EZ3T - 8EZ3T4 types
EVA
A port
EVB
B port
X
EVA
7.12
196
184.5
7.26
EVB
2 0 1
3.43
87
EVB
2 0 1 3
A B
58
2.28
Wrenches and tightening torques
X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Y = allen wrench 3 - 5 Nm (3.7 lbf)
dead band
800 400
650 / 325 mA
400 200
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
position 1 Stroke position 2
72 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Electrohydraulic controls
Control Types
1 : With AMP JPT connector - AMP JPT mating connector, code: 5CON003
2 : With Deutsch DT04 connector - Deutsch DT06-2S mating connector code: 5CON140031
EVB 2 0 1 EVB
2 0 1
#
U
G G
2
1
K J
EVA
A port
EVB
B port
7.12
196
184.5
7.26
X
3.43
87
70
2.76
122.5
4.82
D1WWED02E 73
DPC200 DPC Series
Working section___________________________________________________________________________________________
2 0 1 3 53
2.09
45 20.4 20.4
3 ° 0.80 0.80
32 1
°
11
58.5 8° 0
45° 30'
2.30
60°
18
X
°3
0'
53
2.09
62.5
2.46
W Z Y 0
54.5
2.15
60
°
104
4.09
2
B
20.4
0.80
60°
M8
Lever with turned
Wrenches and tightening torque assembling
4
X = allen wrench 5 - 9.8 Nm (7.2 lbf)
Y = allen wrench 3
Z = wrench 10 - 9.8 Nm (7.2 lbf)
W = allen wrench 4 - 6.6 Nm (4.9 lbf)
R = wrench 8
Cast iron lever box, without lever; LGN type Aluminium lever box; L type
2 0 1 3 2 0 1 3
Z Y W Z Y
X
X
X X
B B
74 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Port valves
Pressure
300 260 bar (3750 psi) 4500
210 bar (3050 psi)
200 3000
140 bar (2050 psi)
80 bar (1150 psi)
C type 100 1500
6.69
170
200
Pressure
0.37
9.5
10 150
eC
Typ 100
17.95 46.8 48.5 25.75 5 U
ype 50
0.707 1.84 1.91 1.014 T
0 0
Wrenches and tightening torque 0 10 20 30 40 50 60 (l/min)
X = wrench 13 - 24 Nm (17.7 lbf) Flow
Y = wrench 19 - 42 Nm (31 lbf)
300 4500
250 bar (3600 psi)
200 bar (2900 psi)
200 3000
150 bar (2150 psi)
100 bar (1450 psi)
100 1500
6.69
170
ty
L
Y 20
U 300
e
typ 200
CL
10
100
valve position is the same as U type
0 0
0 40 80 120 160 (l/min)
Flow
D1WWED02E 75
DPC200 DPC Series
Working section___________________________________________________________________________________________
A
X X
J J
LSZ ST
cap part
6.69
170
K
6.18
157
4COP116420
X J
Legenda
LSH: with lock arrangement
0.59
15
2000
std. setting(1)
100
min. setting(1) 1000
0 0
0 40 80 120 160 200 240 (l/min)
Flow
76 D1WWED02E
DPC Series DPC200
__________________________________________________________________
Outlet section part ordering codes
1 2 3 4 1 2 3 4
3 1 2 3 1 2
2 2
1 1
1 1
3
1
D1WWED02E 77
DPC200 DPC Series
Outlet section______________________________________________________________________________________________
X
171.5
6.75
6.34
161
4.29
109
1.85
47
34.5
1.36
0.63
16
21.25 12 5.25
X
0.47
12
to tank).
M12
11.5 25 134
0.45 0.98 5.28
47.6 52.4 T2
1.87 2.06
23.8 26.2 3/8-16 UNC
0.94 1.04 nr. 4+4 threads
P2 L
L
26.2
1.03
13.1
0.52
4.29
109
22.2
4.29
38.5
1.52
11.1
0.44
27.75 17.25
1.093 0.679 LS1
49.5
1.95
76.5
3.01
78 D1WWED02E
DPC Series DPC200
______________________________________________________________________________________________
Outlet section
Drain options
Option 1 1
internal drain for
L mechanical controls Option 1 Option 2 Option 3
F
J
6.34
161
152.5
6.00
Option 2 2
L
internal drain for
hydraulic controls
Option 33
external drain for
Dim. F electrohydraulic controls
Option
mm in
N
1 3.5 0.138
2 3.5 0.138
3 19 0.75
D1WWED02E 79
Special configurations DPC Series
DPC200/1/BR2-10(D220\ELP)/C30-104(200\200)-8EZ3TLG1.UTUT/EIR/C10-1S8EZ3TL1/RF30/DPC130/1-......
Nr. of working Inlet section Working section 1 Working Outlet Nr. of working
sections section section sections
3
1
2
DPC200 side assembling kit 3
DPC130 side assembling kit
CODE CODE DESCRIPTION CODE DESCRIPTION
With inlet section type 5TIR108112 For 1 working section valve
BR type BRF type 5TIR108160 For 2 working section valve
5TIR112180 5TIR112141 For 1 working section valve 5TIR108208 For 3 working section valve
5TIR112235 5TIR112194 For 2 working section valve 5TIR108256 For 4 working section valve
5TIR112287 5TIR112247 For 3 working section valve 5TIR108304 For 5 working section valve
5TIR112340 5TIR112300 For 4 working section valve 5TIR108352 For 6 working section valve
5TIR112393 5TIR112354 For 5 working section valve 5TIR108400 For 7 working section valve
5TIR112446 5TIR112407 For 6 working section valve 5TIR108448 For 8 working section valve
5TIR112499 5TIR112460 For 7 working section valve 5TIR108496 For 9 working section valve
5TIR112552 5TIR112512 For 8 working section valve
5TIR112605 5TIR112565 For 9 working section valve
80 D1WWED02E
DPC Series Special configurations
______________________________________________________________
Connection between DPC Series valve
EVA1
EVA2 A1 port
A2 port
EVB2 EVB1
B2 port B1 port
dim. E dim. F
1.30
sections
working
33
36.5
1.44
Nr. of
BR BRF
inlet section inlet section
A2 A1 P
L mm in mm in mm in
1 101.5 4.00 73.1 2.88 97 3.82
3.94
100
5.28
8.17 7.05 7.60
207
134
3 207.5 179.1 193
T
B2 4 260.5 10.26 232.1 9.14 241 9.49
5 313.5 12.34 285.1 11.22 289 11.38
6 366.5 14.43 338.1 13.31 337 13.27
B1 7 419.5 16.52 391.1 15.40 385 15.16
8 472.5 18.60 444.1 17.48 433 17.05
9 525.5 20.69 497.1 19.57 481 18.94
LS
LS2
F 45 E
1.77
B2 A2 B1 A1
P T
M
V2
L
V1
EVA2
EVB1
LS
EVB2 EVA1
D1WWED02E 81
Accessories DPC Series
Connectors
Coil type Voltage Packard Packard Flying leads
ISO4400 Deutsch DT AMP JPT
Weatherpack Metri-pack (without conn.)
10 VDC 4SLE001000A - - - - -
4SLE001201A(5)
4SLE001209A(3-4)
4SLE001200A 4SLE001203A(4)
12 VDC 4SLE001202A(5) 4SLE001210A(2) 4SLE001214A(2) 4SLE001207A
4SLE001217A(3) 4SLE001211A(3-4)
4SLE001216A(3-5)
4SLE001206A(2)
4SLE001400A(5)
14 VDC - 4SLE001401A(3-5) 4SLE001403A(3-4) - - -
4SLE001402A(3-4)
BER 4SLE002400A 4SLE002401A(4)
24 VDC 4SLE002408A(3) 4SLE002407A(3-4) 4SLE002403A(4) - - 4SLE002404A
4SLE302400A(1) 4SLE002402A(5)
28 VDC - 4SLE002802A(5) 4SLE002800A(4) - - -
4SLE004800A
48 VDC - - - - -
4SLE304800A(1)
4SLE011000A
110VDC - - - - -
4SLE311000A(1)
4SLE022000A
220 VDC - - - - -
4SLE322000A(1)
12 VDC 4SL5000126A 4SL5000125A(6) 4SL5000129A(5) - - -
BQP19
24 VDC 4SL5000245A 4SL5000244A(6) 4SL5000248A(5) - - -
10 VDC 4SL3000100
4SL3000130(6)
4SL3000120 4SL3000122(5)
12 VDC 4SL3000134(3-6) 4SL3000124(2) 4SL3000127(2) 4SL300012C
4SL3000126(4) 4SL3001200(3-5)
4SL3000128(2)
4SL3000240 4SL3000249(6)
24 VDC 4SL3000248(5) - - 4SL3000246
4SL3030240(1) 4SL300024C(3-6)
BT 26 VDC 4SL3000260 - - - - -
4SL3000480
48 VDC - - - - -
4SL3030480(1)
4SL3001100
110 VDC - - - - -
4SL3031100(1)
4SL3002200
220 VDC - - - -
4SL3032200(1)
Mating connectors
Standard 4CN1009995 5CON140031 5CON003 - -
24VDC 4CN3010240 - - - -
48VDC 4CN3010480 - - - -
With rectifier
110VDC 4CN3011100 - - - -
220VDC 4CN3012200 - - - -
Notes: (1) supply with AC and use only with rectifier connector - (2) with flying leads - (3) with bidirectional diode - (5) with unidirectional diode
(5) integrated perpendicular type - (6) integrated parallel type
82 D1WWED02E
DPC Series Accessories
_____________________________________________________________________________________
Coils and connectors
BER type
ISO4400 connector DEUTSCH DT04 connector Features
(perpendicular type) Nominal voltage tolerance : ±10%
Power rating. . . . . . . . . . : 19.2 W - 10/12/24/48/
110/220 VDC
: 19 W - 24/110/220 RAC
59.8
2.35
: 19.2 W - 48 RAC
68
47.5
1.87
47.8
1.88
23.5
0.93
: 1.61 A - 12 VDC
38.5 36
: 0.80 A - 24 VDC
38.5 36
1.52 1.42 1.52 1.42 : 0.40 A - 48 VDC
: 0.17 A - 110 VDC
: 0.09 A - 220 VDC
DEUTSCH DT04 connector AMP JPT connector : 0.89 A - 24 RAC
(parallel type) : 0.45 A - 48 RAC
: 0.19 A - 110 RAC
: 0.09 A - 220 RAC
Coil insulance. . . . . . . . . : Class H (180°C - 356°F)
69.8
2.75
63.9
2.52
47.5
1.88
1.87
0.93
0.93
Flying leads with Flying leads with PACKARD Flying leads with PACKARD
Flying leads DEUTSCH DT04 connector WEATHER-PACK connector METRI-PACK connector
200 150 150
7.87 5.91 5.91
11.81
300
8
47.8
1.88
23.5
0.93
38.5 36
1.52 1.42
BQP19 type
ISO4400 connector DEUTSCH DT04 connector Features
Nominal voltage tolerance : ±10%
Power rating. . . . . . . . . . : 15 W @ 12 VDC
: 15 W @ 24 VDC
Max. operating current . . : 1.25 A @ 12 VDC
66.5
74.4
2.62
2.93
: 0.63 A @ 24VDC
54,5
2.13
54
22.5
0.89
(180°C - 356°F)
55 45
Weather protection. . . . . : IP65 - ISO4400
55 45
2.17 1.77 2.17 1.77 : IP69K - Deutsch DT
: IP65 - AMP JPT
Insertion . . . . . . . . . . . . : 100%
AMP JPT connector
66.5
2.62
2.13
54
22.5
0.89
55 45
2.17 1.77
D1WWED02E 83
Accessories DPC Series
53.25
2.07
2.10
40.5
1.59
40.5
: 17.3 W - 110 VDC
1.59
18.25
18.25
0.72
0.72
: 19.9 W - 24 RAC
50 Ø 36.5 50 Ø 36.5
1.97 1.44 : 20.7 W - 48 RAC
1.97 1.44
: 20 W - 110 / 220 RAC
Max. operating current . . : 1.9 A - 10 VDC
Flying leads : 1.77 A - 12 VDC
DEUTSCH DT04 connector : 0.89 A - 24VDC
: 0.84 A - 26 VDC
: 0.43 A - 48 VDC
L
42.5
1.67
40.5
: 0.93 A - 24 RAC
1.59
18.25
19.5
0.77
0.72
: 0.47 A - 48 RAC
: 0.18 A - 110 RAC
50 Ø 36.5 50 Ø 37.5
: 0.09 A - 220 RAC
1.97 1.44 1.97 Ø 1.48
Coil insulance. . . . . . . . . : Class F (155°C - 311°F)
Weather protection. . . . . : IP65 - ISO4400
Dimension L : IP69K - Deutsch DT
Coil type
(mm) (in) : IP65 - AMP JPT
: IP67 - Weatherpack
12VDC 247 9.72
: IP67 - Metri-pack
24VDC 307 12.09 Insertion . . . . . . . . . . . . : 100%
84 D1WWED02E
DPC Series Installation
___________________________________________________________________________________________________
Main rules
The DPC Series valves are assembled and tested as per the technical specifications of this catalogue.
Before the final installation on your equipment, please follow the below recommendations:
- the valve can be assembled in any position; in order to prevent body deformation and spool sticking mount the product
on a flat surface;
- In order to prevent the possibility of water entering the spool control kit, do not use high pressure washdown directly on the
valve;
- prior to painting, ensure plugs on normally open ports are tightly in place.
B
B
A L A
T L
T P
P
V1
V2
LS
V2
LS
V1
With O-Ring seal 120 / 88.5 120 / 88.5 190 / 140 25 / 18.4 25 / 18.4 25 / 18.4
With copper washer 120 / 88.5 120 / 88.5 190 / 140 30 / 22.1 30 / 22.1 30 / 22.1
With steel and
120 / 88.5 120 / 88.5 190 / 140 16 / 11.8 16 / 11.8 16 / 11.8
rubber washer
DPC200
NOTE – These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating
and surface finish.
D1WWED02E 85
Installation DPC Series
Series DPC working sections are arranged for external operation of LS signal through dedicated ports on the lower side of
sections.
For the maximum permissible pipe length please contact Sales Dpt.
LSB LSA
lever side
lever side
lever side
LSAB LSA LSB
Appendix A__________________________________________________________________________________________________
Max stroke
Stroke
I2 - I1
Hysteresis % = x 100
50% of IMAX
max stroke
0
0 I1 I2 IMAX
Current
86 D1WWED02E
DPC Series
D1WWED02E 87
7th edition June 2017 WWW.WALVOIL.COM
D1WWED02E