Professional Documents
Culture Documents
01 Tombo Gasket PDF
01 Tombo Gasket PDF
GASKETS
Contents
Safe Usage/Explanatory notes for customers ………………………………… 1
Definitions of Terminology …………………………………………………………………………… 2
Gasket Selection ……………………………………………………………………………………………… 3∼5
■ High Temperature Use Sheet Gaskets ……………………………………………… 6
■ Joint Sheets ………………………………………………………………………………………………… 7∼13
■ Vortex Gaskets ………………………………………………………………………………………… 12∼29
■ Metal Gaskets ………………………………………………………………………………………… 30∼36
■ Metal Jacketed Gaskets …………………………………………………………………… 37∼39
■ GRASEALTM Gaskets ……………………………………………………………………………… 40∼41
TM
■ NAFLON Gaskets ……………………………………………………………………………… 42∼53
■ Cloth Gaskets ………………………………………………………………………………………… 54∼55
■ Rubber Gaskets ……………………………………………………………………………………… 56∼57
■ Other Gaskets …………………………………………………………………………………………… 58∼59
■ Gasket Paste ……………………………………………………………………………………………… 60∼61
■ Standard Dimension Charts …………………………………………………………… 63∼108
! CAUTIONS
Properties/applications shown throughout this catalog are typical.
Performance data referred to in this catalog are based on our own test results and on performance in general
applications under normal conditions.
Products listed in this catalog are used in diverse locations and for numerous types of machinery and equipment, and
actual conditions of use also differ extensively. Consequently, when using these products, we recommend that you
implement verification tests under the actual conditions of use.
Regarding individual applications, it is necessary to make a selection decision based on individual designs and on
suitability evaluations. For special applications, please consult us.
The contents of this catalog are subject to change without prior notice.
1. Never use for any purpose other than the prescribed application.
2. When processing, use sharp cutting tools.
3. Always follow the instructions in this catalog or the instruction manual when installing equipment, etc.
4. Do not re-use gaskets unless this is specifically indicated.
5. When replacing, carefully remove all of the old material before installing the new product.
6. To maintain performance, store packaged products in a cool and dark place.
7. Please refer to MSDS (Material Safety Data Sheet) concerning health and hygiene cautions.
8. When disposing, comply with all regulations in your country. Waste should be properly disposed of at a permitted
disposal site. Do not incinerate the used products, especially those containing fluoropolymer resin as it will generate
toxic gas when burning.
¡TOMBO
“TOMBO” is a registered trademark of NICHIAS Corporation.
¡JIS Japanese Industrial Standards
¡JPI The Japan Petroleum Institute
¡ASME American Society of Mechanical Engineers
¡API American Petroleum Institute
¡BS British Standards
¡ISO International Organization for Standardization
*All brand names and product names are trademarks or registered trademarks of NICHIAS Corporation.
1
Definitions of Terminology
Fluids
In this catalog, the fluids sealed with gaskets are classified as follows.
Depending on the type of gasket, however, there are various cases where one type
of gasket cannot always be used in the same way for the same fluid.
Wm1= – π G2P+2πbGmP
4
Wm2=πbGy
P = internal pressure
G = effective gasket diameter
b = effective gasket width
m= gasket factor
y = minimum designed seating stress
In some cases, however, this seating stress may not be sufficient depending on
certain types of fluids and or certain types of gaskets. So, among the three seating
stresses (Wm1, Wm2, Wm3), the largest value shall be employed as the minimum
seating stress.
Wm3=σ3 Ag
σ3= minimum seating stress
Ag = gasket contact area (projected surface area)
The minimum seating stresses used in this catalog is "σ3" in the above
equation, and not "y".
2
Gasket Selection
Please select a gasket from the following gasket selection table considering 1fluid, 2pressure and 3temperature.
Operating conditions Recommended gasket
1Fluid 2 3 Remarks
Ñ
Temperature Pressure TOMBO No. Product name
(℃) MPa
18 1850C-G Ring Joint Gasket
600
18 1836R-GS Vortex Gasket GS
29 1850C-F Ring Joint Gasket
450
29 1834R-GR GRASEAL Vortex Gasket
400 3.6 1215,1210-A GRASEAL Gasket PM, MI-A
34 1850C-F Ring Joint Gasket
350 34 1834R-GR GRASEAL Vortex Gasket
12 1834R-NA NA Vortex Gasket
39 1850C-F Ring Joint Gasket
Steam 260 39 1834R-GR GRASEAL Vortex Gasket
14 1834R-NA NA Vortex Gasket
Hot water
215 2.0 1120 CLINSIL-Top
Water 1.5 9007-LC NAFLON PTFE Low Creep Gasket
200
1.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
Salt water
(Brine) 1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
150
1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
44 1850C-F Ring Joint Gasket
44 1834R-GR GRASEAL Vortex Gasket
16 1834R-NA NA Vortex Gasket
100 4.0 1120 CLINSIL-TOP
1.8 1995 CLINSIL-Brown
1.0 1051-CR Cloth Reinforced Rubber Cut Gasket
0.5 9007 NAFLON PTFE Cut Gasket
18 1850C-G Ring Joint Gasket
600
11 1836R-GS Vortex Gasket GS
29 1850C-F Ring Joint Gasket
450
17 1834R-GR GRASEAL Vortex Gasket
400 3.6 1215,1210-A GRASEAL Gasket PM, MI-A
Petroleum-
based 34 1850C-F Ring Joint Gasket
carbonated 350 21 1834R-GR GRASEAL Vortex Gasket
hydrogen 8.0 1834R-NA NA Vortex Gasket
Gasoline 39 1850C-F Ring Joint Gasket
Naphtha 23 1834R-GR GRASEAL Vortex Gasket
260
Kerosene 9.0 1834R-NA NA Vortex Gasket
Light oil
1.0 1120 CLINSIL-Top
Heavy oil
Lubricating oil 1.5 9007-LC NAFLON PTFE Low Creep Gasket
200
Oil gas 1.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
LPG 1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
150
Alcohol 1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
44 1850C-F Ring Joint Gasket
Animal and 26 1834R-GR GRASEAL Vortex Gasket
vegetable oils
11 1834R-NA NA Vortex Gasket
100 3.0 1120 CLINSIL-Top
1.8 1995 CLINSIL-Brown
0.5 9007 NAFLON PTFE Cut Gasket
0.5 9007-LP NAFLON PFA Gasket
*This selection guide shows typical recommended gaskets for fluids, temperatures and pressures.
Thus, depending on the other conditions, the products shown here are not necessarily suitable for use in some cases.
*Please refer to service temperature range of each gasket on this catalog regard the maximum service temperature.
*In some cases, the product numbers shown here are only representative examples for that type.
3
Gasket Selection
Operating conditions Recommended gasket
1Fluid 2 3 Remarks
Ñ
Temperature Pressure TOMBO No. Product name
(℃) MPa
18 1850C-G Ring Joint Gasket
600
11 1836R-GS Vortex Gasket GS
29 1850C-F Ring Joint Gasket
450
17 1834R-GR GRASEAL Vortex Gasket
400 3.6 1215,1210-A GRASEAL Gasket PM, MI-A
34 1850C-F Ring Joint Gasket
Aromatics- 350 21 1834R-GR GRASEAL Vortex Gasket
based 8.0 1834R-NA NA Vortex Gasket
carbonated
39 1850C-F Ring Joint Gasket
hydrogen
260 23 1834R-GR GRASEAL Vortex Gasket
Benzene 9.0 1834R-NA NA Vortex Gasket
Toluene 1.5 9007-LC NAFLON PTFE Low Creep Gasket
Xylene 200
1.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
Organic 1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
solutions 150
1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
Heat transfer 44 1850C-F Ring Joint Gasket
solutions 26 1834R-GR GRASEAL Vortex Gasket
11 1834R-NA NA Vortex Gasket
100 3.0 9007-LC NAFLON PTFE Low Creep Gasket
1.8 9010-NA-A-5,7 NAFLON PTFE Cushion Gasket
0.5 9007 NAFLON PTFE Cut Gasket
0.5 9007-LP NAFLON PFA Gasket
9.0 1834R-GR GRASEAL Vortex Gasket
9.0 1834R-NA NA Vortex Gasket
260
4.6 1215,1210-A GRASEAL Gasket PM, MI-A
1.0 1120 CLINSIL-Top
1.5 9007-LC NAFLON PTFE Low Creep Gasket
200
Weak acid 1.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
Weak alkali 150
1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
Salt solutions 11 1834R-GR GRASEAL Vortex Gasket
11 1834R-NA NA Vortex Gasket
100 1.8 1120 CLINSIL-Top
1.8 1995 CLINSIL-Brown
0.5 9007 NAFLON PTFE Cut Gasket
260 9.0 9090-IOR NAFLON Vortex Gasket
1.5 9007-LC NAFLON PTFE Low Creep Gasket
200
1.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
Acids
Sulphuric acid 1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
150
Hydrochloric acid 1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
Nitric acid 11 9090-IOR NAFLON Vortex Gasket
Acetic acid
1.8 9007-LC NAFLON PTFE Low Creep Gasket
100
1.0 9010-NA-A-5,7 NAFLON PTFE Cushion Gasket
0.5 9007 NAFLON PTFE Cut Gasket
4
Gasket Selection
Operating conditions Recommended gasket
1Fluid 2 3 Remarks
Ñ
Temperature Pressure TOMBO No. Product name
(℃) MPa
9.0 1834R-GR GRASEAL Vortex Gasket
260
4.6 1215,1210-A GRASEAL Gasket PM, MI-A
200 1.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
Alkali 150 1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
Caustic soda
11 1834R-NA NA Vortex Gasket
Caustic
potassium 1.8 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
100 1.8 1120 CLINSIL-Top
1.0 9010-NA-A-5,7 NAFLON PTFE Cushion Gasket
0.5 9007 NAFLON PTFE Cut Gasket
600 0.3 1841-Fi-G High-temperature NA Metal Jacketed Gasket Used together with high-temperature gasket paste.
300 5.0 1834R-GR GRASEAL Vortex Gasket
260 1.0 1120 CLINSIL-Top
1.5 9007-LC NAFLON PTFE Low Creep Gasket
200 1.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket
Air 1.5 9010-NA-A-9 NAFLON PTFE Cushion Gasket
1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
150
1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
1.0 1995 CLINSIL-Brown Used together with gasket paste.
100 1.0 1050-EP Rubber Cut gasket
0.5 9007 NAFLON PTFE Cut Gasket
700 0.01 1400-ST Super Manhole Gasket-ST Suitable for applications where slight leakage is permissible.
500 0.01 1400-TH FF Manhole Gasket Suitable for applications where slight leakage is permissible.
Exhaust gas 300 0.01 1374 NA Manhole Gasket Suitable for applications where slight leakage is permissible.
200 1.0 1120 CLINSIL-Top
100 1.0 1995 CLINSIL-Brown
600 18 1850C-G Ring Joint Gasket
29 1850C-F Ring Joint Gasket
450
17 1834R-GR GRASEAL Vortex Gasket
34 1850C-F Ring Joint Gasket
Combustible 350 21 1834R-GR GRASEAL Vortex Gasket
gas 5.0 1834R-NA NA Vortex Gasket
39 1850C-F Ring Joint Gasket
Toxic gas 23 1834R-GR GRASEAL Vortex Gasket
260
Hydrogen gas 9.0 9090-IOR NAFLON Vortex Gasket
6.0 1834R-NA NA Vortex Gasket
Ammonia 200 1.5 9007-LC NAFLON PTFE Low Creep Gasket
1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
150
1.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket
0.5 9007 NAFLON PTFE Cut Gasket
100
0.5 9007-LP NAFLON PFA Gasket
260 39 1850C-F Ring Joint Gasket
9.0 9090-IOR-OX NAFLON Vortex Gasket
Oxygen gas
100 1.8 9010-NA-A-5 NAFLON PTFE Cushion Gasket
1.8 9007-LC NAFLON PTFE Low Creep Gasket
Low-temperature 20 1834R-GR GRASEAL Vortex Gasket
-240
fluids Liquid gas LNG, 11 1839R GRASEAL Vortex Gasket L
LN2 LO2, Ethylene
-200 1.0 1120-LN CLINSIL-Top LN
5
■High Temperature Use Sheet Gasket
HIGH TEMPERATURE USE
■Applicable standards
TA LUFT/VDI GUIDE LINE 2440 (HELIUM LEAKAGE) ■Functional performance versus steam
Typical test data in steal line
■Availability <Condition>
Thickness Temperature : 215℃
Width×Length
0.4 0.5 0.8 1.0 1.5 2.0 3.0 Pressure : 2MPa
1270×1270 (1S) ○ ○ ○ ○ ○ ○ ○ Fluid : Steam
1270×3810 (3S) ○ ○ ○ ○ ○ ○ ○ Gasket Thickness : 1.5mm
2540×3810 (6S) ― ― ― ○ ○ ○ ○ Flange : JIS20K 25A RF
Fastening Surface Pressure : 29.4MPa
Venue : Boiler at Nichias' factory
■Recommended seating stress of Gasket :
Please refer to page 8. <Result>
776days No leakage
■Chemical resistance : Test under implementation as of May in 2008
CLINSIL-Top Asbestos joint sheet
(TOMBO No.1120) (TOMBO No.1100)
30.0
Tensile strength(N/mm2)
25.0
20.0
15.0
10.0
! Handling instructions
Since gaseous fluids have a higher tendency to leak than water-based and oil-based fluids, please pay attention to and follow the handling
instructions below.
¡Gaskets should be ring-shaped (Type FR) in thickness of 1.5mm or less.
¡Apply a small amount of the gasket paste (TOMBO No. 9105, 9106) thinly and evenly to the inner edge and both faces of gasket.
¡When gasket is tightened in place, do not tighten more than the tolerable seating stress.
Pay attention to the tendency that seating stress becomes greater than the tolerance in the case of flanges in small diameter.
¡Pay attention to the tendency that seating stress at compression failure declines less than the values shown on page11 in the case where gasket
6 is tightened under elevated temperatures (hot bolting).
■JOINT SHEETS
Compressed fiber joint sheet is a gasket made of a uniform mixture of fibrous material, filler, rubber and
chemicals which is hot rolled by calendering to obtain smooth sheets. The sheets are processed to the required
shapes and dimensions for applications in equipment, etc., in a wide range of industries.
JOINT SHEETS
TM
CLINSIL -Brown TOMBOÑ No.1995
■Features : Inorganic filler is added to inorganic fibers
and aramid fibers; then oil-resistant synthetic rubber is
added as binder to form brown NA (non-asbestos) joint
sheets which contain absolutely no asbestos.
This gasket can be used for stainless steel flange since
leachable halogens are little.
Large diameter gasket cut from the sheet of 3,810mm x3,810mm (9S
size) max. in monolithic form is available.
■Applications : Gaskets for various types of piping
flanges and valves, equipment, etc.
■Service Range (For details, please refer to the
diagram on page 10.)
¡Temperature : –100℃ ∼ 183℃
¡Pressure : Saturated steam, hot water
→See Page 10
Water, salt solutions, weak acid and
weak alkali solutions. →Max.3.0MPa
Oil at 100℃ or lower. →Max.3.0MPa TOMBO No. 1995
Air, exhaust gas, inert gas. ! Caution for Steam Sealing more than 100℃
→Max.1.0MPa ¡Use ring shape (FR) and 1.5A gasket.
■Applicable standards ¡Minimum recommended compressive stress for TOMBO
API 6FA (FIRESAFE) BAM OXYGEN GAS SERVICE
GERMANISCHER LLOYD GL TYPE No. 1995 is 29.4NE
TA LUFT/VDI GUIDE LINE 2440 (HELIUM LEAKAGE) ¡TOMBO No. 1993 is recommended when maximum
ASTM F104 F712100-B5E12M5 operating pressure is 0.5MPa and over.
JIS F 0602 HJ JIS F 7102 HJ
■Availability ¡Use Vortex gaskets, etc. in places where maintenance is
difficult.
Thickness
Width×Length ¡Re-torque immediately before temperature rise.
0.8 1.0 1.5 2.0 3.0
¡Do not re-torque after temperature rise.
1270×1270 (1S) ○ ○ ○ ○ ○
¡Avoid piping stress to installed gaskets.
1270×3810 (3S) ○ ○ ○ ○ ○
2540×3810 (6S) ─ ○ ○ ○ ○
3810×3810 (9S) ─ ─ ○ ○ ○
JOINT SHEETS
Aramid fibers, inorganic fibers, inorganic filler and
oil-resistant rubber are mixed uniformly and then
Union joints JIS F 0602 HJ
1938 CLINSIL-UF compressed and calendered to form NA (non- –100 ∼ 100
Fluid: water, hot water, gas ASTM F104 (F712100)
asbestos) joint sheets with outstanding shear
strength and easy cutting feature.
■Availability
TOMBOÑ No.1938 TOMBOÑ No.1991-NF
Thickness – – – 1.0 1.5 2.0 – Thickness 0.4 0.5 0.8 1.0 – – –
1270×1270 (1S) 1270×1270 (1S)
Width×Length Width×Length
1270×3810 (3S)
8 9
Service Range
Ñ TM
TOMBO No.1120 CLINSIL -Top
JOINT SHEETS
215℃ 200℃
2.0 2.0 2.0
C
260℃
260℃
1.0 1.0 1.0
0 0 0
0 50 100 150 200 250 280 0 50 100 150 200 250 280 0 50 100 150 200 250 280
Fluid temperature(℃) Fluid temperature(℃) Fluid temperature(℃)
*Please consult us for the service other than the above service range.
Ñ TM
TOMBO No.1995 CLINSIL -Brown
¡Water type fluids ¡Oil type fluids ¡Gas type fluids
6.0 Note:Recommended gasket 6.0 Note: Do not use for aromatic- 6.0 Note: Do not use for toxic gases
life for steam pipe sealing at based fluids. or combustion promoting gas
Fluid pressure (MPa)
*For steam higher than 100℃, hot water, please refer to cautions in page 7.
Ñ TM
TOMBO No.1993 CLINSIL -Super
¡Water type fluids ¡Oil type fluids ¡Gas type fluids
6.0 Note: Recommended gasket life 6.0 Note: Do not use for aromatic- 6.0 Note: Do not use for toxic gases
for steam sealing is as follows: based fluids. or combustion promoting gas
Fluid pressure (MPa)
Fluid pressure (MPa)
Fluid pressure (MPa)
0 0 0
0 50 100 150 200 250 0 50 100 150 200 250 0 50 100 150 200 250
Fluid temperature(℃) Fluid temperature(℃) Fluid temperature(℃)
*For steam higher than 120℃, hot water, please refer to cautions in page 7.
10
Cautions
■Flange Finish ■Installation
The recommended surface roughness of flange is Tighten bolts from side to side around the joint in a
JOINT SHEETS
as follows : star like crossing pattern.
¡For liquids 6.3 Ra All bolts should be tightened in four to five
¡For gas 3.2 Ra
increments, according proper bolting patterns.
Immediate tightening can cause leaks and
■Seating Stress compression damage.
The seating stress should be one the maximum value, as
shown below:
a. Wm1 according to JIS B 8265.
b. Wm2 according to JIS B 8265. 1 5
c. Minimum seating stress required for sealing
liquids.
¡For water, oil : 14.7N/E 7 3
¡For gas : 34.3N /E
■Preventive measures for permeation leakage
of gaseous fluids
The joint sheet has disadvantage that it has a high 4 8
tendency to have permeation leakage in the case of
gaseous fluids since it is not physically dense material
6 2
due to the characteristics of its material component.
¡Apply a small amount of gasket paste uniformly
on the surface and inner diameter.
¡Apply enough seating stress.(Please refer above.) Bolt tightening sequence
¡Gaskets should be ring-shaped (FR shape) with a ■Gasket Thickness
thickness of 1.5A or less. We recommend the use of gasket thickness
¡When an air tight test is required, 2-3 hours after depending on the nominal diameter of the flange as
tightening. follows.
¡Non-asbestos joint sheet shall not be used for 150A (6B) or below: 1.5A
toxic gas or high vacuum sealing. 200A (8B) and above: 3.0A
! Caution
■Non-asbestos Joint Sheets for stainless steel
flanges ¡We recommend a thickness of 1.5At regardless of
TOMBO No.1993, 1995, 1120 are recommended for the consideration above if TOMBO No.1995 is
this service since leachable halogens are little. used for steam or hot water at the temperature of
Gasket paste (TOMBO No.9120) is not required over 100゜ .
generally. However, if paste is used, please consult us. ¡We recommend a thickness of 1.5At regardless of
■Compression failure the consideration above if TOMBO No.1993 is
¡Fastening force used for steam or hot water at the temperature of
If excessive tightening force is applied to non- over 120゜ .
asbestos joint sheets, compression failure may
occur. When tightening joint sheets, refer to the ■Placing orders
following maximum tolerable seating stress. ¡Sheets
Please specify the thickness, width and length.
Maximum tolerable seating stress Example: 1.5t×1270×1270 or 1.5t×1S.
NA joint sheet Thickness Without paste With paste ¡Cut gaskets
TOMBO No. A N/E N/E In the case of flanges for JIS or JPI (ANSI) piping,
1120 0.8 294.2 68.6 etc., please specify pressure rating (class),
1995 1.5 196.1 68.6 nominal diameter, flange type (RF or FF) and
gasket thickness.
1993 3.0 147.1 68.6 Example: JIS 10K×50A, RF, 1.5t,
Value inside ( ) is for TOMBO No. 1120
JPI class 150×2B, RF, 1.5t.
Due to low physical strength of NA joint sheets, Please provide a drawing for non-standard
special precautions should be made to avoid dimensions.
uneven tightening.
! Caution
¡Combined use of gasket paste
Do not apply solvent-based liquid packing (which ¡These joint sheet gaskets contain organic
makes gaskets swell), silicon-based oil or grease materials; therefore they are not recommended for
(which makes gaskets slippery) on NA joint sheets combustion promoting application gas (oxygen
as gasket paste, as they may cause compression gas).
failure at a pressure lower than the above values ¡For further details, please refer to the separate
of seating stress. handling instructions.
If using gasket paste, TOMBO No. 9105 or 9106 is
recommended.
Please consult with us regarding other pastes. 11
■VORTEX GASKETS TM
■Construction
Vortex gaskets are made of thin V-shaped metal
hoops and non-metallic cushioning filler. These are
wound into a spiral shape by welding at the beginning
and end of the spiral winding. Vortex gaskets are
available in four types: basic, with an inner ring, with
an outer ring, and with both inner and outer rings.
VORTEX GASKETS
12
■Shape
¡Basic type
Vortex gaskets are made of thin metal hoops and
non-metallic cushioning filler. These are wound
into a spiral shape by welding at the beginning and
end of the spiral windings.
This type is used for Male & Female (M&F) type
VORTEX GASKETS
flanges and Tongue and Groove (T&G) type
flanges, but is not recommended for the raised face
Filler Hoop
of ordinary piping flanges.
Cross section of the Vortex gasket with both inner and outer rings
13
Expanded Graphite Tape Filler Vortex Gaskets
TM
GRASEAL Vortex Gasket TOMBOÑ No. 1804-GR Series
This Vortex gasket uses expanded graphite tape (GRASEAL tape) as the
filler material which provides superb sealability even under severe
conditions such as high temperatures, high pressures, cryogenic
temperatures, heat cycles, temperature cycles and so on.
■Features
VORTEX GASKETS
■Applications
Suitable for use in piping flanges, pressure vessels, heat
exchangers, valve bonnets, etc.
TOMBO No. 1834-NA
Please pay attention when flanges are released after temporary ■Service Range
setting of machinery or hydraulic test. Filler material may stick to
Maximum service Maximum service
flanges. Please consult us if gaskets are used like this. Fluid temperature℃ pressure
Water type fluids 350 Class 1500
Oil type fluids 350 Class 600
Gas type fluids 350 Class 400
14
PTFE Tape Filler Vortex Gaskets
TM
NAFLON Vortex Gasket TOMBOÑ No. 9090 Series
This Vortex gasket uses unsintered PTFE tape as
the filler material. The PTFE filler provides
superior chemical resistance and sealability. By
combining with corrosion resistant metals, it can
be applied for corrosive fluids, pure oxygen gas
VORTEX GASKETS
and vacuum lines.
■Features
1. Sealability is superior to that of all other Vortex
gaskets. It can also be used for vacuum lines.
2. The highest corrosion resistance among the all Vortex
gaskets. It can be used for almost all fluids by selecting
appropriate hoop materials
TOMBO No. 9090-IOR
■Applications
■Service Range
Suitable for use in piping flanges, pressure vessels, heat
exchangers, valve bonnets, etc. especially for corrosive Fluid Maximum service Maximum service
temperature℃ pressure
fluids and oxygen for which other Vortex gaskets cannot
be used, places where a high degree of air tightness is Water type fluids 300 Class 600
required, as well as vacuum lines. Oil type fluids 300 Class 600
The OX type, which has no oil in the PTFE, is available for Gas type fluids 300 Class 600
use with pure oxygen.
15
Composite Filler Vortex Gaskets for High-temperature Applications
TM
Vortex Gasket-GS, -GM, -GH TOMBOÑ No. 1806- GS,-GM, -GH Series
Non-asbestos Vortex gasket for high temperature
service for which normal GRASEAL Vortex cannot
be used. Combination of mica layers and GRASEAL
filler with anti-oxidant prevents oxidation of
GRASEAL at high temperature.
We offer a line up of three types GS, GM, and GH,
VORTEX GASKETS
■GS Series
Mica
Suitable for non-oxidizing fluids of 450℃ and above.
(Ordinary GRASEAL Vortex gaskets are recommended for
temperatures below 450℃)
When fluids contain oxygen, do not use at temperature of 450℃
or higher.
■GM Series
Suitable for high-temperature conditions over 450℃, and
usage conditions where there is decoking. Mica
(For temperatures below 450℃, ordinary GRASEAL
Vortex gasket is recommended.)
When the internal fluid is air, do not use at temperatures of 450℃
or higher.
16
Expanded Graphite Filler Vortex Gaskets for Low-temperature, Low Seating Stress Service
TM
GRASEAL Vortex Gasket L TOMBOÑ No. 1809 Series
Protruding graphite tape (GRASEAL) is used on the
gasket surface to make this gasket suitable for
cryogenic applications.
■Features
VORTEX GASKETS
1. Outstanding sealability for cryogenic fluids such as LNG, etc.
2. Superb sealability even in low seating stress.
■Applications
Suitable for services such as:
* Cryogenic lines for LNG, LN2, LO2, LHe, etc.
* Locations where adequate seating stress for ordinary
GRASEAL Vortex gasket is not attainable.
TOMBO No. 1839R
■Service Range
Fluid Maximum service Maximum service
temperature℃ pressure
Water type fluids 450 Class 600
Oil type fluids 450 Class 600
Gas type fluids 450 Class 600
Cryogenic –240
11MPa
temperature fluids (Min. service temperature) GRASEAL
Expanded Graphite Filler Vortex Gaskets for use with Aluminum Flanges
TM
GRASEAL Vortex Gasket for Aluminum Flanges TOMBOÑ No. 1809-AL Series
This GRASEAL Vortex gasket for aluminum flanges
uses a combination of aluminum and type 304
stainless steel as the hoop material.
■Features
1. Suitable for aluminum flanges.
2. Outstanding sealability for cryogenic fluids such as
LNG, etc.
3. Superb sealability even in low seating stress service.
■Applications
Suitable for cryogenic temperature lines such as LNG, LN2,
LH2, LHe and aluminum flanges.
TOMBO No. 1839RAL
■Service Range
Fluid Maximum service Maximum service
temperature℃ pressure
Water type fluids 300 Class 600 GRASEAL
Stainless steel hoop
Oil type fluids 300 Class 600
Gas type fluids 300 Class 600
Cryogenic –240
11MPa
temperature fluids (Min. service temperature)
Aluminum hoop
17
Irregular-shape Spiral Wound Gaskets
TM
Irregular-shape Vortex Gasket
JOINT SHEETS
before ordering.)
■Applications
Mainly used for boiler manholes, hand holes and valve
bonnets, etc.
R1 R1 R1 R1
R3
C A R2
R1 =ー R2
2 R3 A
B B
B
C C
C
Notes: (1) When ordering gaskets, please indicate the dimensions A, B, C, (2) Dimension A for oval and track shapes: Shall be 40mm or over.
R1, R2 and R3 shown in the diagram. R3 is not necessary with Dimension A for diamond and square shapes: Shall be 60mm or over.
diamond shapes where R3 is a straight line. (3) Ratio A/B shall be 2/3 or over.
■Applications
Used for general heat exchangers.
18
Special Construction Spiral Wound Gaskets
TM
Special Construction Vortex Gasket
Inner ring rod type
This type of Vortex gasket has a metal rod instead
of a regular type inner ring.
■Applications
VORTEX GASKETS
Recommended where the regular type inner ring cannot
be installed.
19
Design standard
■Gasket, Inner and Outer ring thickness ■Available inner diameters Unit: A
Unit: A
Gasket Inner and outer ring thickness Gasket Available inner diameters
thickness Carbon steel Other than carbon steel thickness Minimum Maximum
3.2 2.0 2.0 3.2 16 600
4.5(standard) 3.2 3.0 4.5 16 (3000)
6.4 4.5 4.0 6.4 1500 (3000)
*Please consult with us in case of dimensions over values in
VORTEX GASKETS
20
Other Joint Sheets
■Recommended gasket widths (for a gasket thickness of 4.5mm)
30
Recommended width
25
VORTEX GASKETS
Recommended minimum widths for
NA Vortex gaskets.
20
Gasket width (A)
10
0
16 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400
Full Face Raised Face Male & Female Tongue & Groove
(FF) (RF) (M&F) ( T&G)
With inner and outer ring (1) With inner and outer ring (1) With inner ring (1) Basic type
Notes:(1) The type without an inner ring can be used if the following conditions are fully satisfied.
Filler material : NA paper.
Pressure rating : Class 600 or below, or 40K or below.
Size : Nominal diameter 24B or below, or 600A or below.
21
Notes for Designing
■Applicable flanges
(1) Since Vortex gaskets require a comparatively
high tightening stress, do not use for low-
pressure flanges (JIS 2K, 5K, vacuum lines, etc.).
(2) Only TOMBO No. 1809-AL Series Vortex gaskets
can be used for aluminum flanges.
■Necessity of inner ring Buckling
VORTEX GASKETS
0.7 0.7 a b
631∼1600 1.0 1.0
1601 or above 1.5 1.5
(2) Flat to Groove flange
Clearance (b) differs depending on the seating
stress of the gasket.
Please consult us for designing the clearance. Application for Tongue & Groove (T&G) flange
■Gasket thickness and suitable groove
depth
(1) Tongue & Groove (T&G) and Male & Female
(M&F) flange Unit: A
Gasket thickness Suitable groove depth (f)
3.2 3.5 or more
4.5 5.0 or more
6.4 7.0 or more
(2) Flat to Groove flange Unit: A
f
22
■Gasket seating stress ■Bolt materials
(1) For general liquids : Since Vortex gasket require comparatively high
The calculation results Wm1 and Wm2, stipulated in tightening stress, high tension bolt such as SNB 7 or
JIS B 8265, etc., shall be calculated using m and y. over is recommended for bolt specification.
The largest stress obtained from the calculation shall
be the required seating stress.
(2) For fluids that tend to leak:
For gas type fluids, leakage may occur if only seating
VORTEX GASKETS
stress calculated by JIS B8265,etc. is applied.
In addition to Wm1 and Wm2, the seating stress
(Wm3) shall also be calculated in accordance with the
following σ3 per unit of gasket contact surface. The
largest stress from the calculation shall be used as the
required seating stress.
N/E N/E
TOMBO No.1804-GR Series 39.2
TOMBO No.1804-NA Series 78.4
68.9
TOMBO No.9090 Series 39.2
TOMBO No. 1806 -GS -GM -GH 3.00 78.4
29.4 (Class 150)
TOMBO No.1809 Series 58.8 39.2 (Class 300)
49.0 (Class 600)
notes:(1),(2) Specified by JIS B 2205 (1991), JIS B (1995) and JPI-7S-81-96.
(3) Specified by test results from NICHIAS Corporation
¡Tightening
To obtain uniform seating stress, apply the tightening
load (torque) in 4 - 5 stages, proceeding diagonally as
Cautions shown in the diagram below. Gradually increase the
¡Storage strength of the tightening load until the prescribed
1. Store gaskets indoors in a cool, dark place in the seating stress is obtained. After that further tighten by
original wrapping. proceeding clockwise 1 - 2 turns.
2. Do not stand gaskets upright or hang them. ¡Basic-type Vortex
3. Do not bend, twist, push or press gaskets. Basic-type Vortex gaskets (including irregular-type
¡Installation gaskets) should be carefully handled as they
1. Before installing a gasket, first clean the surface of the deform easily with even with slight external force.
flange and check the surface is free of foreign matters, Even if gaskets are somewhat deformed, they may
scratches, etc. still be fitted into the groove on the flange and
2. Do not handle gaskets roughly. Since large diameter used, depending on the condition of the gasket. In
gasket is easily damaged (dropping off of windings), it such cases, please consult with us.
should be handled very carefully by several persons.
3. Place gaskets carefully in correct position.
4. In principle, there is no need to apply gasket paste. 1 5
But, if considered necessary NAFLON paste (TOMBO
No. 9400) is recommended for temperature conditions
of 300℃ or lower, 7 3
5. Do not re-use gaskets.
4 8
6 2
23
■Compression recovery curve
137
118
Compression load (N/E)
VORTEX GASKETS
Class 300 x 8B
98
Class 600 x 8B
79
59
39
20
0
4.6 4.4 4.2 4.0 3.8 3.6 3.4 3.2
79
Class 300 x 3B
Compression load (N/E)
59 Class 300 x 8B
39
20
0
4.6 4.4 4.2 4.0 3.8 3.6 3.4 3.2
24
●TOMBOÑ No.1839R (4.5t) compression recovery
Gasket ; TOMBO No.1839R
137 Size 8B ;ø220 x ø236 x ø260 x ø307 x 4.5t (Class 300)
ø209 x ø230 x ø260 x ø320 x 4.5t (Class 600)
118
Compression load (N/E)
VORTEX GASKETS
98
Class 600 x 8B
79
Class 300 x 8B
59
39
20
0
4.6 4.4 4.2 4.0 3.8 3.6 3.4
118
Compression load (N/E)
98
Class 600 x 8B
79
59
Class 300 x 8B
39
20
0
4.4 4.2 4.0 3.8 3.6 3.4 3.2
25
Selection Guide Design Points
¡Water type fluids ¡Oil type fluids
50 50
Class2500 Class2500 1 GR 1 GS
1 GR 2 NA 2 GM
1 GS
Class1500 Class1500
1 GR 1 GR
20 20
2 NA 1 GS 1 GS
Class900 Class900 2 GM
Class600 Class600
10 10
VORTEX GASKETS
1 GH
Class400 Class400
Class300 Class300
5 5
1 GR 1 GR
Pressure (MPa)
Pressure (MPa)
2 NA 2 NA
3 PTFE 3 PTFE
2500 2500
Class150 Class150
2 2
1500 1500
1 900 1 900
600 600
0.5 0.5
400 400
300 300
0.2 0.2
150 150
0.1 0.1
0 0
-200 -100 0 100 200 300 400 500 600 700 800 900 1000 -200 -100 0 100 200 300 400 500 600 700 800 900 1000
10 Class600 Class600
1 GR 10
2 PTFE 1 PTFE
Class400 1 GR 2 GR
Class400
5 Class300 Class300
1 GR 5
1 PTFE
2 PTFE
Pressure (MPa)
Pressure (MPa)
2 GR
3 NA
2500
Class150 2500
2 Class150
1 GS 2
1500
2 GM 1500
3 GH 1 GR
1
900 1 900
600 1 GR
600
0.5
0.5
1 GH 400
400
300
300
0.2
0.2
150 150
0.1
0.1
0
0
-200 -100 0 100 200 300 400 500 600 700 800 900 1000
-200 -100 0 100 200 300 400 500 600 700 800 900 1000
26
Design Points
■Selection chart ■Applicable fluids
1. The following codes indicate the gasket types: Pay special attention when selecting Vortex gaskets
Code Product TOMBO No. for the following fluids.
1. Combustion promoting gas (oxygen):
GR GRASEAL Vortex 1804-GR Series
Use only NAFLON Vortex OX type (TOMBO No.
NA NA Vortex 1804-NA Series 9090-OX etc.) which contains no oil in its filler
PTFE NAFLON Vortex 9090 Series material. Other types of Vortex gasket should not
GS GRASEAL Vortex-GS 1806-GS Series be used since their fillers contain combustible
VORTEX GASKETS
materials.
GM GRASEAL Vortex-GM 1806-GM Series
GH GRASEAL Vortex-GH 1808-GH Series 2. Strong acid fluids:
2. When several recommended gaskets are Do not use GRASEAL Vortex gaskets for strong
indicated by the line connecting temperature and oxidizing acids such as nitric acid and nitrates.
pressure, the priority is indicated by numerical For details, refer to fluids that cannot be used
order. with GRASEAL on page 41.
3. This table is just a general selection guide.
3. High temperature fluids:
Select materials for the hoop and inner ring that
■Service temperature for hoop material can sufficiently withstand usage conditions.
Do not use Vortex Gasket-GS at temperatures of
Material Old material code Recommended service
Type code temperature(℃) 450℃ or above if fluids contain oxygen. If the
oxidative power of the fluids is weak, Vortex
304 Stainless Steel E 304 500 and below Gasket-GM, -GH can be used.
304L Stainless Steel L 304L 500 and below
316 Stainless Steel G 316 600 and below 4. Corrosive fluids:
316L Stainless Steel H 316L 600 and below Select hoop and inner ring materials that are
321 Stainless Steel J 321 750 and below fully capable of withstanding the service
347 Stainless Steel K 347 750 and below conditions.
Inconel 600 Y IN 800 and below
Monel M M 750 and below 5. Acidic fluids:
Titanium T TI 500 and below Do not use NA Vortex gaskets.
27
For ordering
Please specify the following items when ordering Vortex gaskets:
1. Type (basic, with inner ring, with outer ring, with 4. Dimensions
inner and outer rings) (1) Standard size: Applicable standards such as JIS,
2. Special construction (with rib, metal rod, winding JPI, ASME, etc., nominal pressure/ class,
metal hoop, etc.) nominal diameter.
3. Materials (filler, hoop, inner ring, outer ring) (2) Non-standard size: service pressure, dimensions
(inner diameter of inner ring, gasket inner
diameter, gasket outer diameter, outer diameter
VORTEX GASKETS
■Indications
TM TM TM
[GRASEAL Vortex , NA Vortex , Others]
18□□□□□─□□─□□□─□
Outer ring ● ● Special specifications
Yes 3 When special specification is agreed
with end user, this code will be added
No 0
28
TM TM
[GRASEAL Vortex L]
18□9□□□─□□□─□
Outer ring ● ● Special specifications
Yes 3 Only required when so decided
through agreement with the user.
VORTEX GASKETS
No 0
● Inner ring/Material
Application (flange material) ● Yes See table on previous page
Stainless steel None No O
Aluminum AL
● Hoop material
(See table on previous page)
TM TM
[NAFLON Vortex ]
9090─□□□□□─□□□□□─□
Inner ring and Outer ring ● ● Special specifications
Basic type None Only required when so decided
through agreement with the user.
With inner ring IR
With outer ring OR ● Special processing
With inner and outer rings IOR Standard product None
For oxygen OX
Ribs ●
Yes EX ● Outer ring/Material.
No None Yes See table on previous page
No 0
● Inner ring/Material
Yes See table on previous page
No 0
● Hoop material
(See table on previous page)
■Examples of numbering
Materials Old
TOMBO No. Type TOMBO No.
Filler Hoop Inner ring Outer ring
1806-GR-GOO Basic Expanded graphite 316 Stainless Steel None None 1806-GR
1834-NA-EOS With outer ring NA paper 304 Stainless Steel None Carbon steel 1834-NA-SS
9090-IOR-TTG With inner and outer rings PTFE Titanium Titanium 316 Stainless Steel 9090-IOR-TI-TI-316
29
■METAL GASKETS
Metal gaskets are suitable for high pressure and
high temperature duties instead of soft gasket.
Metal gaskets can be produced in any suitable
materials such as soft iron, stainless steel, brass,
aluminum, titanium, special alloy, etc.
Plain and serrated metal gaskets can be used with
flat surface flanges, but other metal gaskets
should be installed to specified flanges.
■Applications : Pipe flanges, valves, pressure vessels,
heat exchangers, etc.
METAL GASKETS
Cross section
TOMBO No.1850P-E
TOMBO No.1890-E
30
Metal Solid Gaskets
Octagonal Ring Joint Gasket TOMBOÑ No.1850C
■Features : These gaskets are processed to solid ring
joints with an octagonal cross section.
Used for high-pressure pipe flanges, vessels and valves.
■Standard dimensions :
Please refer to the table of dimensions at the end.
■Applicable standards
JPI-7S-23
ASME B16.20
API Spec 6A
METAL GASKETS
■Applications : Pipe flanges, valves,
pressure vessels, heat exchangers, etc.
Cross section TOMBO No.1850C-L
31
■Other Metal Solid Gaskets
TOMBO No. Product name Cross section Features
RX ring This ring joint gasket is suited for flanges in accordance with API
1850-RX gasket spec 6A, model 6B.
BX ring This ring joint gasket is suited only for flanges in accordance with
1850-BX gasket API spec 6A, model 6BX.
Lens type The sealing action is based on line contact sealing. Dimensions in
1850-L gasket accordance with DIN 2696
Metal
1850-O A solid metal o-ring.
O-ring
Doble corn
1850 A self sealing type metal gasket with a cross section as shown.
gasket
■Metal material types, material codes, hardness and maximum service temperature
Maximum hardness(3) Maximum service
Main composition(2) Material Old material temperature
Gasket materials(1) code code Remarks
HB HV (℃)
Soft iron - D D 90 - 538 C≦0.05%
Carbon steel - S(4) SS 120 - 538
5Cr - 0.5Mo steel 5Cr-0.5Mo F F5 130 - 649 ASTM A182 F5
13Cr steel 13Cr R 410 170 - 704
Type 304 stainless steel 18Cr-8Ni E 304 160 - 816
Type 304L stainless steel 18Cr-8Ni, LC L 304L 150 - 816
Type 316 stainless steel 16Cr-12Ni-2Mo G 316 160 - 816
Type 316L stainless steel 16Cr-12Ni-2Mo, LC H 316L 150 - 816
Type 321 stainless steel 18Cr-10Ni-Ti J 321 160 - 816
Type 347 stainless steel 18Cr-10Ni-Nb K 347 160 - 816
Aluminum - A Al - 40 300
Copper - C Cu - 80 400
Monel - M M 130 - 800
Nickel - N Ni 120 - 760
Titanium - T Ti 140 - 800
Notes: (1) Materials should be selected with regard to operating temperature and chemical compatibility. Other metal materials are available
upon request.
(2) The alloy ingredients, etc., are indicated.
(3) Hardness of materials to be used for TOMBO No. 1850-P and 1890 may differ from this table. For details, please consult us.
(4) In the case of rolled steel plain metal gaskets, SS is employed.
32
■Indications
18□0□─□
Shape ● ● Material code
Serrated type 9
Other 5
Shape ●
Octagonal type C
Oval type V
RX type RX
BX type BX
METAL GASKETS
Delta type D
Lens type L
Plain type P
Serrated type None
Other None
Top view
(RF Type)
Side view
(RF Type)
Side view
(RTJ Type)
33
Hollow Metal Rings
Metal O-Seal TOMBOÑ No. 9200
Stainless steel or Inconel tubes are formed into an O-ring
shape, the ends are welded together, and then surfaces are
finished ultra-smooth.
PTFE coating or silver plating is used on the surfaces for
sealing gases, vacuum and highly volatile liquids.
Highly reliable sealing performance is provided over a wide
range from high temperatures to cryogenic temperatures, and
from high pressures to vacuum.
This gasket features a compact design that requires a
comparatively low seating stress and requires little space.
METAL GASKETS
■Applications
Valve bonnets, high-pressure vessel flanges, equipment
joints, pipe flanges, plastic processing machinery, rubber
extruders, hydraulic equipment, pneumatic equipment,
vacuum vessels, nuclear power containers, aircraft ■Service range
engines, rocket engines and automobile engines. High-pressure water Up to 400MPa
High pressure gas Up to 300MPa
Vacuum Up to 10-4Pa
■Type
S
TOMBO No. Product name Shape Features
Standard type Metal A standard type Metal O-Seal can be applied from
9200P
O-Seal vacuum to about7.0MPa.
■Indications
9200□─□□□
Shape ● ● Surface treatment material
Standard type P None None
Vent hole type V Silver plating AG
NAFLON coating TF
● Tube material
Type 321 stainless steel J
Inconel 600 Y
34
■Standard dimensions
Tube cross section diameter Wall thickness(3) Outside diameter (A) Compression load(4)
(A) (A) Recommended range Available dimensions N/A
0.8 0.15* 6(5)∼25 6(5)∼30 69
0.25 – 10∼200 118
1.6
0.36* 15∼50 11∼200 284
0.25 – 40∼500 59
2.4
0.46* 40∼200 20∼500 235
0.25 – 60∼1500(6) 49
3.2 0.35 – 60∼1500(6) 88
0.50* 65∼700 50∼1500(6) 177
0.50(7) – 150∼1500(6) 69
4.8
0.80* 500∼1200(6) 150∼1500(6) 333
6.4 0.80* 1000∼1500(6) 250∼1500(6)(8) 177
METAL GASKETS
Notes: (3) Standard wall thickness is indicated with asterisks *. Apply the standard wall thickness for gases.
(4) Indicates the load required to obtain proper seating stress. To obtain the actual seating stress, add the end force to be
calculated to the above.
(5) The minimum outside diameter for the vent hole type is 10A.
(6) The maximum outside diameter for PTFE coating is 1300A; for silver plating, the maximum outside diameter is 1100A.
(7) A tube diameter of 4.8A with a wall thickness of 0.50A is only available with type 321 stainless steel.
(8) Please consult with us if gasket diameter is larger than 1500A.
Notes: ( 9) The groove surface finish is 0.8a (3.2S) for gas and vacuum sealing, and 1.6a (6.3S) for all other cases.
(10) The groove dimensions shall be revised as follows when PTFE coating or silver plating are applied:
Internal pressure sealing: 0.1A shall be added to the groove outside diameter (O.D.), groove width (W) and groove depth (H).
External pressure sealing: 0.1A shall be subtracted from the groove inside diameter (I.D.), and 0.1A shall be added to
the groove width (W) and groove depth (H).
(11) A indicates the gasket outside diameter.
A A
6.3S 6.3S
H H
R R
W W
OD ID
35
Corrugated Metal Gaskets Bonded with Expanded Graphite
TM
CMGC Gasket TOMBOÑ No.1880-GR
Expanded graphite sheet (GRASEAL sheet) is adhered
on both sides of concentric corrugated steel plate (Type
316L stainless steel).
■Features
¡Excellent sealing performance that remains nearly the same
under both low and high temperatures (up to 400℃)
¡Can be used for almost all fluids, with the exception of strong
oxidizing acid.
¡This type of gasket is used widely by major foreignl oil
companies.
■Applications
¡Gasket for piping flange used with fluids such as petroleum, etc.
¡Alternative to conventional asbestos joint sheets
■Standard dimensions Expanded graphite sheet
METAL JACKETED
36
■METAL JACKETED GASKETS
A highly heat resistant core is completely covered with a thin
metal jacket.
Double jacket type as per diagram below is standard, but
other jacketing methods are also available.
These gaskets are used for heat exchangers, pressure vessels,
tanks, equipment, valves, high-temperature joint flanges, and
so on.
■Types
METAL JACKETED
1841-Fi Ceramic fiber felt 3.0 1300
High-temperature applications
GASKETS
6.0
NA Corrugated Metal Jacketed Non-asbestos mill
1861 3.0 530
Gasket board
NA Corrugated Metal Jacketed Gasket
1861-Fi for High-temperature applications Ceramic fiber felt 3.0 1300
Notes: (1) Other types of gaskets with different cross section are also available upon request.
(2) Indicates the heat resistance of the core. The values may become lower, depending on the jacket metal material.
Cautions
(1) The use of expanded graphite tape (TOMBO No. 1220 or TOMBO No. 1221) on the sealing surface is
recommended for more reliable sealing performance at temperatures of 400℃ and below. High-
temperature gasket paste (Never Seize® nickel special grade) is recommended at temperatures higher than
400℃.
(2) Metal Jacket Gaskets are not recommended for standard pipe flanges because it is difficult to obtain
enough seating stress. However, if used even so, gaskets with hangers are recommended for centering.
■Metal types and available dimensions
Metal type (3) Material code Old Maximum service temperature Maximum dimensions (4)
material code ℃ A
Carbon steel S SS 535 1480
Type 304 stainless steel E 304 800 1180
Type 316 stainless steel G 316 800 1180
Type 310S stainless steel V 310S 1150 1180
Aluminum A Al 400 980
Copper C Cu 400 1180
Monel M M 800 890
Notes: (3) Other metal materials are also available upon request.
(4) Indicates the maximum diameter that can be fabricated in one piece without welding. For larger sizes, welded types are also available.
■Applicable standards
ASME B16.20 Jacketed Gaskets
■Indications
18□1─□□─□─□□
Shape ● ● Surface material
Flat 4 None None
Corrugated 6 Graseal GR
Welded construction
A
A'
Filler material
Metal jacket
Section A-A'
38
Heat Exchanger Gasket Standard Shape Codes
Please indicate the shape code and dimensions when ordering.
This shape is top view from Side A of right diagram.
Side A
W
W
W
R R R
W
R
R
P P
R R
P P
P
t t t t t
METAL JACKETED
I.D. I.D. I.D. I.D. I.D.
GASKETS
W
R R R
R
W
P1
P1
W
R
W
R
P
P
R R R
PP
W
R
P
P
R
P1
P1
R
t t t t t
W
R R R R R R
R R
W
R R R R R R
P
P
R R
P
P
R
R
R
t t t t t
R
W
R R
W
R R R
W
R
R R R
P1 P1
R R R R
P1 P1
R R R
P
R R
P P
P P
R R
P
R
t t t t t
R R R R
R
W
W
W
R R R
R R R
P1 P1
W
W
P P1
P P1
R R R R R R R
R R
P P
P1 P
P1 P
R
R
R R R
t t t t t
P1P1
[HE26] [HE27] [HE28]
O.D.
O.D. O.D. I.D.
I.D. I.D. P P
R R
W
RR RR R
W
R
P1
P1
R
P1 P1
R R R R R R R
P P
P P
R
P1
P1
R
t t t
39
■GRASEAL GASKETS TM
■Features
1. Sealability remains almost same throughout a range of
cryogenic to high temperature (400℃).
2. Excellent chemical resistance to almost all liquids other
than strong oxidizing acids, etc.
3. Since cold flow and creep property are minor, it is not
affected by over-tightening of gasket.
40
Expanding Graphite Gaskets
TM
GRASEAL Gasket Tape TOMBOÑ No.1220/1221
GRASEAL gasket tape is a self-adhesive tape with
a peel off backing and it can easily be installed to
all dimensions and shapes. Two different types are
available for different applications.
¡TOMBO No. 1220 GRASEAL Gasket Tape (Plain)
The surface of this GRASEAL Gasket Tape is smooth.
The 0.25mm thick type is suitable for flanges with large
diameters of 18 inches or over.
¡TOMBO No. 1221 GRASEAL Gasket Tape (Crinkled)
This crinkle processed GRASEAL Gasket Tape is suitable
for flanges with a diameter of about 16 inches or less.
■Applications
1. Use as a free-size gasket by applying directly to the
flange surface. TOMBO No.1220
2. Improving sealability of metal gaskets (TOMBO No.1840,
1850 etc.) by applying this tape on the sealing surface
when seating stress is not adequate. ■Standard sizes
3. Plain tape with a thickness of 0.13A can be used as a Type Thickness(A) Width(A) Length(mtr)
tape sealant for high-pressure threaded joints up to 0.13 12.7 7.6
300℃. TOMBO No.1220 0.25 12.7 7.6
GRASEAL GASKETS
Cautions 0.25 25.4 15.2
Do not use together with soft gaskets such as joint TOMBO No.1221 0.38 12.7 7.2
sheets. 0.38 25.4 14.2
■Not
! applicable
Type Fluid name
Oxidizing acids Nitric acid, concentrated sulphuric acid, hot
sulphuric acid, mixed acids, chromic acid,etc.
Oxidizing salts Nitrate, chlorate, hypochlorite, etc.
Halogen compounds Bromine, fluorine, iodine, chlorine dioxide, etc.
Combustion promoting gas Oxygen (pure oxygen)
41
Fluoropolymer Gaskets Having Excellent Anti-corrosion Property
TM
NAFLON PTFE Cut Gasket TOMBOÑ No.9007
This is anti-corrosion NAFLON gaskets made of pure PTFE sheets by
punching to the prescribed dimensions and shapes.
As PTFE offers outstanding chemical resistance and does not contaminate
fluids, it can be used as a gasket material in a wide range of industries.
For the services more than 100℃, filled PTFE gaskets which improve anti-
creep property is recommended.
■Applications
¡Various corrosive fluids, such as strong acids, strong alkalis, organic solvents.
¡Fluids where contamination is not allowed.
TOMBO No. 9007
¡Services where electrical insulating property is required.
■Applicable standards
JPI-7S-75
■Design standard
Standard Maximum Gasket Minimum Maximum allowable Service Maximum(1)
TOMBO No. thickness outer diameter factor seating stress y seating stress temperature service pressur
A A C N/E N/E ℃ MPa
1.0 3.5 24.5
1.5 3.2 22.6
9007 1200 39.2 –100∼100 1.0
2.0 3.0 19.6
3.0 2.5 19.6
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, please
refer to page 45.
*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
NAFLON GASKETS
■Applicable standard
JPI-7S-75
■Design standard
Standard Maximum Gasket Minimum Maximum allowable Service Maximum(1)
TOMBO No. thickness outer diameter factor seating stress y seating stress temperature service pressur
A A C N/E N/E ℃ MPa
1.0 3.5 24.5
1.5 3.2 22.6
9007-G20 980 49.0 –100∼150 2.0
2.0 3.0 19.6
3.0 2.5 19.6
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, please
refer to page 45.
*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
42
Fluoropolymer Gaskets Having Low Creep Property (Yellowish White Color)
TM
NAFLON Special Filler Filled PTFE Cut Gasket TOMBOÑ No.9007-LC
This is low creep PTFE cut gasket filled with a special
anti-corrosion, highly temperature resistant inorganic
filler. Its maximum service temperature is 200℃.
This gasket can be used for almost all chemicals except
hydrofluoric acid and strong alkalis. For hydrofluoric acid
and strong alkalis, TOMBO No. 9007-SC is recommended.
■Applications
¡High temperature strong acids, such as chloric acid, nitric acid,
sulfuric acid etc.
TOMBO No. 9007-LC
¡Petroleum and petrochemical products, organic solvents, heat
oil, heat media, steam.
¡Services where electrical insulating property is required.
■Design standard
Standard Maximum Gasket Minimum Maximum allowable Service Maximum(1)
TOMBO No. thickness outer diameter factor seating stress y seating stress temperature service pressur
A A C N/E N/E ℃ MPa
9007-LC 2.0 1200 3.0 24.5 49.0 –100∼200 3.0
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, please
refer to page 45.
*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
NAFLON GASKETS
TM
NAFLON Special Filler Filled PTFE Cut Gasket TOMBOÑ No.9007-SC
This is low creep PTFE cut gasket filled with special
carbon. Its maximum service temperature is 200℃.
This gasket can be used for almost all chemicals except
oxidizing acids, such as sulfuring acid (conc.), nitric acid
(conc.) etc.
For oxidizing acids, TOMBO No. 9007 is recommended.
■Applications
¡High temperature strong alkalis, such as sodium hydroxide,
potassium hydroxide etc.
TOMBO No. 9007-SC
¡Petroleum and petrochemical products, organic solvents, heat
oil, heat media, steam.
■Caution
This gasket can not be used for the service where electrical
insulation is rerquired.
■Design standard
Standard Maximum Gasket Minimum Maximum allowable Service Maximum(1)
TOMBO No. thickness outer diameter factor seating stress y seating stress temperature service pressur
A A C N/E N/E ℃ MPa
9007-SC 2.0 1200 4.0 29.4 58.8 –100∼200 3.0
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, please
refer to page 45.
*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
43
Flexible Fluoropolymer Gaskets (Brown Color)
TM
NAFLON GL Gasket TOMBOÑ No.9007-GL
This gasket is made from PTFE with special anti-corrosion
and heat resistant filler. Good in flexibility and suitable
for the pipings where high tightening stress can not be
obtained, glass lined pipings and plastic pipings.
This gasket can be used for almost all chemicals except
strong alkalis such as sodium hydroxidie and
hydrofluoric acid. For the process which required white
color gasket, TOMBO No. 9007-FD is recommended.
■Applications TOMBO No. 9007-GL
¡Pipings and equipment which high tightening stress can not be
obtained, such as glass lined piping, plastic piping, equipment
made from carbon, etc.
¡Strong acids, such as chloric acid, nitric acid, sulfuring acid etc.,
organic solvents.
■Design standard
Standard Maximum Gasket Minimum Maximum allowable Service Maximum(1)
TOMBO No. thickness outer diameter factor seating stress y seating stress temperature service pressur
A A C N/E N/E ℃ MPa
9007-GL 3.0 600 2.5 19.6 39.2 –100∼200 2.0
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, please
refer to page 45.
*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
NAFLON GASKETS
■Design standard
Standard Maximum Gasket Minimum Maximum allowable Service Maximum(1)
TOMBO No. thickness outer diameter factor seating stress y seating stress temperature service pressur
A A C N/E N/E ℃ MPa
9007-FD 3.0 1200 2.5 19.6 39.2 –100∼200 2.0
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, please
refer to page 45.
*Not recommended to use for gaseous fluids.
44
Less Permeable Fluoropolymer Gasket (Brown Color)
TM
NAFLON LP Gasket TOMBOÑ No.9007-LP
Brown color gasket made from special PFA. This PFA
material has excellent chemical resistance, and permeation
of chemicals and gases through resin is very small.
Therfore, this gasket is suitable to seal halogens
(chlorine, bromine etc.) which have very strong
permeability to fluoropolymer.
■Applications
¡Strong alkalis, such as chloric acid, nitric acid, sulfuric acid etc.
and halogens.
TOMBO No. 9007-LP
¡Petroleum and petrochemical products, various corrosive fluids,
organic solvents.
■Design standard
Standard Maximum Gasket Minimum Maximum allowable Service Maximum(1)
TOMBO No. thickness outer diameter factor seating stress y seating stress temperature service pressur
A A C N/E N/E ℃ MPa
9007-LP 2.0 277 3.0 19.6 29.4 –100∼100 1.0
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, please
refer to the figure below.
*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
NAFLON GASKETS
Service Range
TM Ñ
NAFLON PTFE Solid Gasket (TOMBO No. 9007 Series)
Notes : (2) Not recommended to use for full face (Type FF)
flange.
(3) Not recommended to use for gaseous fluids.
45
PTFE Enveloped Gaskets
TM
NAFLON PTFE Cushion Gasket TOMBOÑ No.9010
The core of non-asbestos joint sheets, non-asbestos paper, etc.,
which have high cushioning properties, are covered with a thin
PTFE film. This gasket is more resistant to creep than a PTFE
cut gasket (TOMBO No. 9007).
Due to the PTFE film covering the inner diameter and sealing
surface of the gasket, there is no contamination of fluids.
Furthermore, due to the excellent chemical resistance and
solvent resistance of the PTFE film, this gasket can be used for
a wide range of applications in various fields such as fine
chemicals, petrochemicals, pharmaceuticals, foodstuffs, and
general industries.
■Applications
TOMBO No. 9010-NA-A-5, 9010-NA-R-A-5
¡Various corrosive fluids, organic solvents.
¡Fluids where contamination is not allowed.
¡Where electrical insulation is required.
■Applicable standards
JPI-7S-75
NAFLON GASKETS
■Gasket construction
Gasket type Cross section Construction and explanation
The same as type A but with a square inner section. There is little space inside the gasket,
so there is less possibility of damage by the rapid expansion of air due to temperature rises.
AS
Appropriate design of the inside diameter reduces the accumulation of liquid and smoothes
the flow in the fluid.
R-A
The same as types A and AS but with the outer periphery sealed. Fluid from
the exterior cannot penetrate or leak into the core. Because of this
construction, even when used in vacuum lines, the covering strongly resists
being pulled inside. Since there is no turning of the covering, setting is
smooth even when the flange gap is narrow.
R-AS
■Cautions
Please refer to page 49.
46
■Type of Core
Core type Cross section and core material Construction and explanation
NAFLON GASKETS
■Indications
9 0 1 0 ─ N A ─ □─□
● Core type
● Gasket type
● Indication for non-asbestos
■Design standard
Minimum inside Maximum outside Minimum Maximum allowable Service Maximum (2)
Gasket factor
Type diameter diameter Core type seating stress seating stress temperature service pressure
C
A A N/E N/E ℃ MPa
5, 6 3.5 14.7 29.4 –30∼150 (1) 2.0
A 16 1000 7, 8 3.5 14.7 29.4 –30∼150 2.0
9 3.5 19.6 39.2 –30∼200 2.0
5, 6 3.5 14.7 29.4 –30∼150 (1) 2.0
AS 20 700 7, 8 3.5 14.7 29.4 –30∼150 2.0
9 3.5 19.6 39.2 –30∼200 2.0
5, 6 4 19.6 29.4 –30∼150 (1) 2.0
B 300 As specified
7, 8 4 19.6 29.4 –30∼150 2.0
Notes : (1) Not recommended for use in locations with frequent thermal fluctuations exceeding 100℃ and pressure fluctuation, or in
locations where maintenance work is difficult.
Notes : (2) The indicated service pressures are for ambient temperatures. These values become lower at higher temperature.
For detailed service range, please refer to page 49.
47
■NAFLON PTFE Cusion Gasket Standard products list for various piping
TM
For safety use by maintaining original function of NAFLON PTFE cushion gasket, we set the standard material,
shape, dimension for several piping materials.
Please select right products with refering the table below.
5
6
14∼60B B P83
7
8
5
ASME B16.1 CLASS 125 6
26∼96B B P85
Taylor Forge CLASS 250 7
8
5
ASME B16.47 CLASS 150 6
Series A 26∼60B B P84
(MSS SP-44-1996) CLASS 300 7
8
15∼25A AS 7
JIS 10 K P101
NAFLON lined 40∼300A A 7
piping 1 / 2∼1B AS 7
ASME(JPI) 150 LB P88
1-1 / 2∼12B A 7
Asahi Techno 6
Glass lined piping 10K 20∼200A A P97
Glass GL piping 8
Other Piping Please consult with us for detailed designing.
48
■Service Range
TM Ñ
NAFLON PTFE Cushion Gasket (TOMBO No. 9010 Series)
Pressure
MPa
Core type 5 - 8
(For core type 5 and 6, Core type 5 and 6 is not
recommended for the place where thermal and
pressure fluctuation is often happened and the
place where maintenance work is difficult.) Core type 9
Temperature(õ)
NAFLON GASKETS
shall be applied. PTFE envelop.
¡Especially for core type 6 and 8, these core
■For Installation materials have such tendency.
¡Before setting the gasket, make sure that flange ¡So, air tight test shall be conducted well after
surface is free from foreign material or scratch. internal pressure is applied.
¡When setting the gasket, make sure to have
enough distance between flanges. If gasket is ■Others
forced to insert, it may cause leakage by ¡Bolt tightening may be loosen in long time or after
damaging the gasket or peeling off of PTFE heat cycles.
envelope. ¡Bolt tightening shall be checked periodically and
¡If enough distance between flanges are not when bolt is loosen, re-tightening shall be done by
available, "R" type is recommended. initial bolt torque.
¡This type will prevent damage and peeling off of ¡When thermal stress or bending stress is
PTFE envelope during installation. repeatedly applied to the flanges, gasket seating
¡For core types of 6 and 8, seating stress at stress is easily reduced.
compression failure declines when the gasket ¡This gasket is not recommended for such part.
becomes wet. ■Cautions for selection of PTFE Cushion gasket
Therefore, store the gaskets in water-proof bags. ¡Some of the fluids may permeate to inside of the
In addition, take precautions so that gasket does gasket thru PTFE envelope.
not become wet by rain after installation. ¡Especially nitric acid, ethylene chloride, halogens
If the gasket is not tightened enough, soap-water (chroline, bromine, etc.), molten sulfur and mono-
from pneumatic testing or rain-water could chloroacetic acid may attack the cushioning
permeate and soften the non-asbestos paper, material by permeation in long time and as a
pushing non-asbestos paper out of the gasket. result, gasket function will be lost. In such case,
Take precautions since in such cases, the seating gasket shall be changed periodically or use PTFE
stress on the gasket decreases and leakage can occur. cut gasket instead.
¡Do not reuse materials that have already been ¡When type "A", "B" and "AS" type is used for
used once. vacuum service, PTFE envelope may be pulled in.
■Seating Stress In such case, "R" type is recommended.
¡Seating stress of gasket shall be controlled to ¡Due to its shape of "A" type, fluid may remain in
maintain 29.4N/mm2 max. the space between flanges and gasket. To avoid
¡If gasket seating stress becomes more than this this fluid remaining, "AS" type with appropriate
value, jointing sheet of the core may be destroyed. gasket inner diameter shall be used.
Uneven tightening also results excess seating ¡For plastic, glass and rubber lined pipings, each
stress partly and will cause for compressive failure. flange has different gasket dimensions although
¡Special attention shall be paid for bolt tightening. flange standard is JIS standard. Please consult us
¡For Fluoropolymer lined piping, we set for proper gasket dimensions if the gaskets are
recommended tightening torque size by size. For used for such pipings.
details, please consult us. 49
Electrical Insulation Bolt Kit TOMBOÑ No.9910 / 9910-H
Electrical Insulation Bolt kit is designed for cathodic
protection.
This kit consisits of bolt with factory applied insulating
sleeve, insulating washers, metal washers and nuts.
■Features
¡Excellent in electrical instulating performance
As all contact area with metal is covered with fluoropolymer and
other high performance materials.
¡Easier installation. TOMBO No. 9910
As insulating sleeve is already applied to bolt, trable of fitting
during installation, such as cracking, chipping, displacement etc.
can be eliminated
¡Solution for complicated purchasing and management.
The problem of excess and deficiency will be resolved because
necessary number of metal washer, insulation washer and nut
are combined as a set for one bolt.
■Standard Size
ASME Flanges : Class 150 - 1/2" to 60"
Class 300 - 1/2" to 60" TOMBO No. 9910-H
JIS Flanges : 10K - 10A to 1500A Insulating Bolt
20K - 10A to 900A
Indication of size Metal Washer
Insulating Washer
Standard size : "Pressure rating" x "Flange size"
ex. Class 150 x 8", JIS 10K x 200A PVdF Coating
Insulating Gasket
50
Electrical Insulation Gasket TOMBOÑ No.9010-NA-E5 / 9007-LC
NAFLON PTFE has excellent electrical insulating
properties.
This electrical insulating gasket is made of PTFE and to
be used for electrical insulation between flanges.
NAFLON GASKETS
9010-NA-E5 NAFLON PTFE Sheet (TOMBO No. 1995)
B type Standard size is up to 24" or 600A.
(26B or 650A and
above) TOMBO No.1995
Non-asbestos joint sheet
■Standard Size
ASME Flanges : Class 150 - 1/2" to 60"
Class 300 - 1/2" to 60"
JIS Flanges : 10K - 10A to 1500A
20K - 10A to 900A
■Service Range
3.0
TOMBO No.9007-LC
Pressure (MPa)
2.0
TOMBO No.9010-NA-E5
(1)
1.0
0
-30 0 100 200 Note : (1) Not recommended for use in locations with frequent
Temperature(℃) thermal fluctuations exceeding 100℃ and pressure
fluctuation, or in locations where maintenance work is
difficult.
51
■Other Fluoropolymer Gaskets
TOMBO No. 9022-A TOMBO No. 9022-PFA TOMBO No. 9028 TOMBO No. 9037 TOMBO No. 9096(OVAL)
Type TOMBO No. Product Name Construction and explanation Cross section Applications, service conditions Service temperature℃
This O-ring is machined form PTFE. Used for flange groove in the same way as rubber O-rings.
There are three types: pure PTFE (TOMBO No. 9028), glass filled Compression ratios are higher than for rubber O-rings. O- –100∼150
9028 NAFLON PTFE O-ring
NAFLON GASKETS
NAFLON GASKETS
PTFE (TOMBO No. 9028-G20) and graphite filled PTFE ring diameter 3.5A or less: 28% or more; 3.5 - 5.7A: 24%
(TOMBO No.9028-GR30). or more; 5.7A or larger: 22% or more.
A free-size string shape packing made by extruding Flanges for chemical ducts, low-pressure –100∼150
9037 NAFLON SP Packing
unsintered PTFE. gas, etc.
Free-size
gasket Soft type gasket made of expanded PTFE. Various cross sectional shapes are
available such as oval, round (R), flat (B), square (K), tube (TB) as well as flat
Ducts, casing, large-diameter vessels, –100∼200
9096 NICHIAS Soft Seal sheet (S). Oval shape is supplied with adhesive tape. Round (R) and tube (TB)
various types of lined vessels, etc.
shapes are supplied without adhesive tape. For flat (B), square (K) and flat (Oval type)
sheet (S) shapes, both with and without adhesive tape are available.
Other NAFLON gaskets available are TOMBO No. 9090 NAFLON Vortex and TOMBO No. 9094 NAFLON Manhole Gasket. For details,
refer to each section.
■Standard dimensions
TOMBO No. Diameter (A) x Length (mtr) TOMBO No. OD (A)×ID (A)×Length (mtr) TOMBO No. Diameter(A)× Length(mtr) TOMBO No. Thickness(A)×Width(A)×Length(mtr) TOMBO No. Indications of type Thickness(A) Width(A)×Length(A)
2.4×15 2× 1×30 10×5 1.0× 20×15 -0.5 0.5
9037 4.0× 9 3× 2×30 9096-R 12×5 1.0× 30×15 -1.0 1.0
9096-BT 1.0× 50×15
5.6× 5 4× 3×30 20×5 -1.5 1.5
5× 4×20 1.0×100×15
Note: TOMBO No. 9096 (round) is not 2.0× 20× 5 -S -2.0 2.0 1500×1500
9096-TB 6× 5×20 treated with adhesive tape 2.0× 30× 5 (Without adhesive -3.0 3.0 1500×3000
7× 6×20 2.0× 50× 5
TOMBO No. Thickness(A)×Width(A)×Length(mtr) 9096-B tape) -4.0 4.0
8× 7×10 3.0× 20× 5
1.5× 3×30 10× 8×10 3.0× 30× 5 -5.0 5.0
9096
3.0× 6×15 12×10×10 3.0× 50× 5 -6.5 6.5
9096 3.0×100× 5
4.5× 9× 8 -10.0 10.0 1500×1500
6.0×12× 5 9096-KT 5.0× 14×10
-1.0 1.0
9096-K 7.0× 20× 5
Note: TOMBO No. 9096 (oval) is treated with -ST -1.5 1.5
adhesive tape. (With adhesive -2.0 2.0 1500×1500
tape) -3.0 3.0
-4.0 4.0
52 53
Manhole Gasket
■Features : These are cloth gaskets coated with a rubber
compound, matching the shape of the manhole.
These gaskets are not completely airtight and should be
used only where a certain amount of leakage is allowable.
Suitable for application to large diameter distorted
flanges and flanges to which only low seating stress is
applied.
FF Manhole gasket TOMBO No. 1400-TH is treated with graphite 600 Black
1400-THG
(Treated with graphite) for anti-sticking.
The based cloth is woven by using metal wires as Diesel engine exhaust
Super Manhole the warp and glass yarn reinforced by metal wires pipes, flue gas duct
1400-NA 600 Black
CLOTH GASKETS
Gasket as the woof, then coating the cloth with rubber and manholes, boiler
using an endless processing method. combustion duct
sealing materials.
The base cloth is woven by using metal wires as the
Super Manhole warp, and ceramics yarn containing metal wires as the
1400-ST 800 White
gasket-ST woof, then impregnating the cloth with heat resistant
joint filler and using an endless processing method.
The based cloth is woven by using metal wires as the
Super Manhole warp and ceramic yarn reinforced by metal wires as the
1400-S 800 Black
Gasket-S woof, then impregnating the cloth with heat resistant
joint filler and using an endless processing method.
Ducts requiring
Inorganic cloth, woven using a special method, is chemical resistance and
NAFLON Manhole solvent resistance/ducts
9094 impregnated with PTFE dispersion. This is then 300 White
gasket for corrosive gases
formed into the shapes of various gaskets. such as acid exhaust
gas, and general gases.
54
Gasket Tape
■Features : This is a cloth tape gasket coated with a
rubber compound to form a multi-layer structure.
These gaskets are not completely airtight and should be
used only where a certain amount of leakage is allowable.
Suitable for application to large diameter distorted
flanges and flanges to which only low seating stress is
applied.
■Types
Maximum service
TOMBO No. Product name Cross Section Construction Application Coroer
temperature (℃)
Manholes/handhol
es for low-
3 layer wrap pressure steam,
NA A tape shaped gasket made by glass cloth
1364 with natural rubber coating and then exhaust gas, hot 400 White
Gasket Tape 4 layer wrap folding it. air, etc.,
autoclaves, large
diameters flanges.
CLOTH GASKETS
1368-G gasket tape TOMBO No. 1368 is treated with graphite for anti- exhaust gas, hot
sticking. air, and dust, etc. 400 Black
(Finished with
graphite)
■Standard dimensions
Type TOMBO No. Nominal thickness Dimensions
1.6 2.5 3.0 3.2 4.0 4.8 5.0 6.0 6.4 7.5 8.0 9.6 10.0
1374, 1374-G ─ ─ ─ ⃝ ─ ⃝ ─ ─ ⃝ ─ ⃝ ⃝ ─
1378 ─ ─ ─ ⃝ ─ ─ ─ ─ ─ ─ ─ ─ ─
1400-TH,1400-THG ─ ─ ─ ─ ⃝ ─ ─ ⃝ ─ ─ ⃝ ─ ⃝
Manhole
1400-ST ─ ⃝ ─ ─ ─ ─ ⃝ ─ ─ ⃝ ─ ─ ⃝ As specified.
Gasket
1400-NA ─ ─ ─ ⃝ ─ ⃝ ─ ─ ⃝ ─ ⃝ ⃝ ─
1400-S ─ ─ ⃝ ─ ─ ─ ⃝ ⃝ ─ ─ ⃝ ─ ⃝
9094 ⃝ ─ ─ ⃝ ─ ⃝ ─ ─ ⃝ ─ ─ ─ ─
1364 ─ ─ ─ ⃝ ─ ⃝ ─ ─ ⃝ ─ ─ ─ ─
Width : 13, 20, 25, 30, 40, 50A
Length: 30mtr
Gasket tape Height : 6.4, 7.9, 9.5, 11.1, 12.7,
1368, 1368-G ─ ─ ─ ⃝ ─ ─ ─ ─ ─ ─ ─ ─ ─ 15.9, 19.1, 22.2, 25.4A
Width : 50A Length : 30mtr
55
Rubber Cut Gasket TOMBOÑ No.1050/1051
■Features : The elasticity, recovery and compatibility of
rubber are utilized to assure sealing at the lowest seating
stress. TOMBO No. 1051 is reinforced with polyester
cloth, but is unsuitable for gas sealing.
■Applications
Select the material in accordance with the service
conditions for various piping flanges, equipment, etc.
■Service Range
Service temperature range : depends on the rubber material.
Maximum service pressure : 1.0MPa
■Type
TOMBO No. Product name Construction
Gasket cut from various types of
1050 Rubber Cut Gasket
rubber sheets.
Gasket cut from various types of ■Standard dimensions Unit: A
1051 Cloth Reinforced rubber sheets reinforced with Thickness 1.0 1.5 2.0 3.0 5.0 10.0 Others
Rubber Cut Gasket polyester cloth. Width 1000
*TOMBO No.1051 is only available for "NBR", "CR" and "NR". Length 1000, 2000, 5000, 10000, 20000
*ZR and PF dimensions are 300 (W) x 300 (L) x 1, 1.5, 2 or 3A (T).
■Service range
Service temperature range : depends on the rubber ■Applicable standards
material. JIS B 2401 AS 568 A
Maximum service pressure : 25MPa (can be used for
greater pressure if used with
back-up ring.)
■Indications
1 0 5 0 ─□□ 2 6 7 0 ─□□
● Material code ● Material code
● TOMBO No. ● TOMBO No.
■Material codes and materials
Material code NBR CR EP IIR SI FA FS NR ZR PF
Ethyl propylene rubber Butyl rubber(weather Silicone rubber Fluorocarbon Fluorocarbon Hydrogen added Perfluoroelastomer
Nitryl rubber Chloroprene rubber
Materrial (weather resistant, resistant, acid resistant, (weather resistant, rubber rubber Natural rubber nitryl rubber rubber
(oil resistant) (weather resistant)
steam resistant) steam resistant) cold resistant) (heat resistant) (corrosion resistant) (oil resistant) (corrosion resistant)
Service temperature −30∼120 −30∼120 −40∼150 −30∼150 −60∼230 −15∼200 0∼200 −20∼100 −30∼150 0∼200
TOMBO No.1050 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
TOMBO No.1051 ○ ○ − − − − − ○ − −
TOMBO No.2670 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
56
TM
Ebilon Gasket (Solid Rubber)TOMBO Ñ
No.9013-EP/-DEP
■Features : Rubber molded gaskets having a cross
sectional shape as per diagram below. Reliable sealing
performance is obtained even at lower seating stress than
that of rubber gasket.
Recommended for locations where service conditions are
not critical and chemical resistance is not particularly
required.
■Types
There are two types using different types rubber.
TOMBO No. 9013-EP: EPDM
TOMBO No. 9013-DEP: Special EPDM for electrolytic cells.
■Service range
Service temperature : –40℃ ∼ 150℃
Maximum service pressure : 1.0MPa
Flange : Full face TOMBO No . 9013-EP
■Standard dimensions
Plastic flanges (equivalent to JIS 10K): 15A - 300A
ASME B16.5 (JPI), Class 150 1/2B ∼ 24B
Rubber Rubber
TM
Ebilon Gasket (PTFE Jacketed) TOMBOÑ No. 9013/9013-D
■Features : Rubber molded gasket having the same cross
sectional shape as TOMBO No.9013 but sealing surface is
jacketed with PTFE film. This gasket has the elasticity of
rubber and the corrosion resistance of PTFE
simultaneously and gives good sealing performance.
Ebilon gaskets are ideal for applications such as PVC
piping and glass lining piping, where only low seating
stress is attainable.
RUBBER GASKETS
■Types
There are two types using different rubber.
TOMBO No. 9013 : PTFE jacketed EPDM
TOMBO No. 9013-D : Special EPDM with jacketed PTFE
for electrolytic cells.
■Service range
Service temperature : –30℃ ∼ 150℃
TOMBO No . 9013
Maximum service pressure : 2.0MPa
Flange : Full face flanges
Flange finish : 6.3 Ra or smoother
■Standard dimensions
Plastic flanges (equivalent to JIS 10K): 15A - 300A PTFE Rubber Rubber
ASME B16.5 (JPI), Class 150 : 1/2B ∼ 24B
57
Sanitary Use Gasket
TM
Saniclean Gasket TOMBOÑ No.9014
This is sanitary use rubber molded gaskets having PTFE
film covering on the sealing surface of the gasket. Thanks
to this unique structure, this gasket has advantages of
rubber gasket and PTFE.
Note :
Flavor change : Change of product at common use beverage
manufacturing process such as bottling etc.
Sanitation : Cleaning work. Washed with clean water,
chlorine water, hot water, alkalis etc.
TOMBO No. 9014-BW, For Ferrule (White rubber)
■Standard dimensions
TOMBO No. 9014-A Nominal TOMBO No. 9014-A (Thread) TOMBO No. 9014-B, BW (Ferrule)
Type
(For thread connector) Size
φA (Inch) φA φB φC φA φB φC
φB
PTFE(0.3t)
1 32.5 29.2 23.0 49.5 43.5 23.1
1-1/2 46.0 42.7 35.6 49.5 43.5 35.8
5.5
6.5
(For Ferrule)
PTFE(0.3t) However, it can also be used for the connectors and ferrule as per ISO 2852 and ISO 2853.
φA
Rubber(EPDM)
φC
* TOMBO No. 9014, Saniclean Gasket conforms to standard of food and food additives (Notice
by Japanese ministry of health and welfare No. 370 in year 1959), No.3-D-2, apparatus of
synthetic resin.
5.3
1.7
1.7
20
Also it passed material and elution test of container and packaging material (Notice by
Japanese ministry of health and welfare No. 85, revised in 1986).
R1.2 φB
58
■Other Gaskets
¡Typical grade
TOMBO No. 1600, METAKOTETM TOMBO No. 1608, METAFOAMTM
Grade For automobile gaskets Grade For general purpose
TS Combination of cold rolled steel (carbon steel) and NBR
OTHER GASKETS
JZ Combination of stainless steel sheet SUS301H and NBR Combination of cold rolled steel (carbon
PS
Combination of stainless steel sheet steel) and NBR base foam rubber.
LZ
SUS301H and Fluoroelastomer (FKM)
Grade For refrigerators Combination of aluminum sheet and
RS Combination of cold rolled steel (carbon steel) and NBR PA
NBR base foam rubber.
RA Combination of aluminum sheet and NBR
Notes : (1)These grades are subject to change without notice.
Notes : (2)For other application such as brake shim, washers etc., please consult us.
Petroleum type oils, oil gas, solvents, solvent vapor, animal oils,
Fluids
hydrocarbon type fluids, exhaust gas, etc. This is suitable for oil, etc.
Maximum service temperature –200∼900℃
Color Light beige
Coverage approx. 200N/G (12.5G/can)
Package 2.5O plastic container
Notes: Do not use for fluids if even slight dissolution is prohibited.
Fluids
Oil, etc.
Maximum service temperature 250℃
Color Gray
Coverage Approx. 350N/G (8.5G/3O can)
Package 1O can and 3O can
Notes: Do not use for fluids if even slight dissolution is prohibited.
Hazardous cargo for ocean / air transportation, IMCO class 3, UN No.1993, Flash point 27-32℃. For details,
please refer to MSDS available separately.
60
NAFLON™ Paste TOMBOÑ No.9400
General purpose gasket paste, made by dispersing
fine colloidal particles of PTFE in water. This
gasket paste is inactive at ambient temperature.
As it is also chemical resistant, this paste can be
used for acids and corrosive fluids. For PTFE type
gasket, this paste is most suitable.
Cautions
1. For gasket paste in can, stir well before using.
2. Small amount layer with a brush, waste, etc. Excessive application may result in gasket damage.
3. To improve the gas sealing performance with joint sheet,
apply gasket paste on the inner circumference to avoid leakage.
GASKET PASTE
4. Place the gasket on the flange before the gasket paste completely dries.
5. Store in a cool, dark place.
61
Standard Dimension Charts
Index ────────────────────────────
For ASME Flanges
For JPI Flanges
For Taylor Forge & Ladish Flanges
For MSS Flanges
63
For ASME B16.1 Flanges Soft Gasket/Full Face Gasket (F.F.)
For ASME B16.5 Flanges
For ASME B 16.1 Cast iron flanges For ASME B 16.5 Steel flanges
Nominal Pipe Inner
Size diameter Class 25 Class 125 Class 150
Outer diameter Bolt circle diameter Outer diameter Bolt circle diameter Outer diameter Bolt circle diameter
D1 n×h n×h n×h
D2 C D2 C D2 C
1/2 21.3 ─ ─ ─ ─ ─ ─ 88.9 60.5 4×15.7
3/4 26.9 ─ ─ ─ ─ ─ ─ 98.6 69.8 4×15.7
1 33.3 ─ ─ ─ 108.0 79.2 4×15.7 108.0 79.2 4×15.7
11/4 42.2 ─ ─ ─ 117.3 88.9 4×15.7 117.3 88.9 4×15.7
11/2 48.5 ─ ─ ─ 127.0 98.6 4×15.7 127.0 98.6 4×15.7
2 60.5 ─ ─ ─ 152.4 120.6 4×19.0 152.4 120.6 4×19.0
21/2 73.2 ─ ─ ─ 177.8 139.7 4×19.0 177.8 139.7 4×19.0
3 88.9 ─ ─ ─ 190.5 152.4 4×19.0 190.5 152.4 4×19.0
31/2 101.6 ─ ─ ─ 215.9 177.8 8×19.0 215.9 177.8 8×19.0
4 114.3 228.6 190.5 8×19.0 228.6 190.5 8×19.0 228.6 190.5 8×19.0
5 141.2 254.0 215.9 8×19.0 254.0 215.9 8×22.4 254.0 215.9 8×22.4
6 168.1 279.4 241.3 8×19.0 279.4 241.3 8×22.4 279.4 241.3 8×22.4
8 218.9 342.9 298.4 8×19.0 342.9 298.4 8×22.4 342.9 298.4 8×22.4
10 273.0 406.4 362.0 12×19.0 406.4 362.0 12×25.4 406.4 362.0 12×25.4
12 323.8 482.6 431.8 12×19.0 482.6 431.8 12×25.4 482.6 431.8 12×25.4
14 355.6 533.4 476.3 12×22.4 533.4 476.2 12×28.4 533.4 476.2 12×28.4
16 406.4 596.9 539.8 16×22.4 596.9 539.8 16×28.4 596.9 539.8 16×28.4
18 457.2 635.0 577.9 16×22.4 635.0 577.8 16×31.8 635.0 577.8 16×31.8
20 508.0 698.5 635.0 20×22.4 698.5 635.0 20×31.8 698.5 635.0 20×31.8
24 609.6 812.8 749.3 20×22.4 812.8 749.3 20×35.1 812.8 749.3 20×35.1
30 762.0 984.2 914.4 28×25.4 984.2 914.4 28×35.1 ─ ─ ─
36 914.4 1,168.4 1,085.8 32×25.4 1,168.4 1,085.8 32×41.1 ─ ─ ─
42 1,066.8 1,346.2 1,257.3 36×28.4 1,346.2 1,257.3 36×41.1 ─ ─ ─
48 1,219.2 1,511.3 1,422.4 44×28.4 1,511.3 1,422.4 44×41.1 ─ ─ ─
54 1,371.6 1,682.8 1,593.8 44×28.4 ─ ─ ─ ─ ─ ─
60 1,524.0 1,854.2 1,759.0 52×31.8 ─ ─ ─ ─ ─ ─
72 1,828.8 2,197.1 2,095.5 60×31.8 ─ ─ ─ ─ ─ ─
84 2,133.6 2,533.6 2,425.7 64×35.1 ─ ─ ─ ─ ─ ─
96 2,438.4 2,876.6 2,755.9 68×35.1 ─ ─ ─ ─ ─ ─
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, (3) Applicable flanges are for ASME B 16.1 Cast Iron Flanges
cloth reinforced rubber cut gaskets, Graseal gaskets and and ASME B 16.5 Steel Pipe Flanges.
PTFE cut gaskets. (4) For class 25, joint sheet gaskets are not recommended.
Dimension Charts
64
For ASME B 16.1 Flanges
For ASME B 16.5 Flanges Soft Gasket/Flat Ring Gasket (F.R.)
For ASME B 16.1 Cast iron flanges For ASME B 16.5 Steel flanges
Nominal Pipe Gasket inner
Size diameter Gasket outer diameter D2 Gasket outer diameter D2
D1
Class 25 Class 125 Class 250 Class 150 Class 300
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, (3) Applicable flanges are for ASME B 16.1 Cast Iron Pipe Flanges and
cloth reinforced rubber cut gaskets, Graseal gaskets and ASME B 16.5 Steel Pipe Flanges.
PTFE cut gaskets. (4) For class 25, joint sheet gaskets are not recommended.
Dimension Charts
Standard
65
For ASME B16.47 Series A Flanges Soft Gasket/Flat Ring Gasket (F.R.)
For MSS SP-44 Flanges
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, cloth reinforced rubber cut gaskets,
Graseal gaskets and PTFE cut gaskets.
(2) This chart shows dimensions as per ASME B 16.21-1978, Non-metallic Flat Gaskets for Pipe
Flanges, converted from inches to millimeters.
(3) Applicable flanges are for ASME B 16.47 Series A and MSS SP–44.
(4) Nominal pipe size 22 for reference only. Size not listed in ASME B16.47.
Dimension Charts
Standard
66
For ASME B16.47 Series B Flanges
For API-605-1980 Flanges Soft Gasket/Flat Ring Gasket (F.R.) Group I
For Taylor Forge Flanges
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, cloth reinforced rubber cut gaskets,
Graseal gaskets and PTFE cut gaskets.
(2) Dimensions for raised face flanges are the same as ASME B16.21-1992 but converted to millimeters from inches.
Dimensions for slip-on flanges are same as JPI-7S-16-85, Group I
(3) Applicable flanges are ASME B16.47 Series B Flanges. However, this chart can also be used for API-605-1980 and JPI-7S-43-85.
For slip-on welded flanges, applicable flanges are JPI-7S-43-85 as well as Taylor Forge flanges.
Dimension Charts
Standard
67
For JPI Male & Female / Soft Gasket
Tongue & Groove Flanges
15 1/2 22 35 25 35 25 35
20 3/4 28 43 33 43 33 43
25 1 34 51 38 51 38 51
(32) (11/4) 44 64 48 64 48 64
40 11/2 49 73 54 73 54 73
50 2 61 92 73 92 73 92
Notes: (1) The material used for these gaskets is mainly joint sheets.
(2) This dimension chart is the same as JPI-7S-16-98 “Dimensions for non-metallic gaskets for
pipes” large male & female dimensions and large tongue & groove dimensions.
(3) Applicable flanges are JPI-7S-15-99.
Dimension Charts
(4) It is better to avoid using the nominal size values in brackets if possible.
Standard
68
For ASME B16.5 Flanges Vorteax Gasket with Outer Ring
TM
Class 150 Class 300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Nominal Pipe
Nominal Pipe Size
Size
Gasket inner Gasket outer Outer ring outer Gasket inner Gasket outer Outer ring outer Gasket inner Gasket outer Outer ring outer Gasket inner Gasket outer Outer ring Gasket inner Gasket outer Outer ring Gasket inner Gasket outer Outer ring Gasket inner Gasket outer Outer ring
diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter outer diameter diameter diameter outer diameter diameter diameter outer diameter diameter diameter outer diameter
A B D2 D3 D4 D2 D3 D4 D2 D3 D4 D2 D3 D4 D2 D3 D4 D2 D3 D4 D2 D3 D4 A B
15 1/2 19.0 31.8 47.8 19.0 31.8 54.1 19.0 31.8 54.1 19.0 31.8 54.1 19.0 31.8 63.5 19.0 31.8 63.5 19.0 31.8 69.8 15 1/2
20 3/4 25.4 39.6 57.2 25.4 39.6 66.8 25.4 39.6 66.8 25.4 39.6 66.8 25.4 39.6 69.8 25.4 39.6 69.8 25.4 39.6 76.2 20 3/4
25 1 31.8 47.8 66.8 31.8 47.8 73.2 31.8 47.8 73.2 31.8 47.8 73.2 31.8 47.8 79.5 31.8 47.8 79.5 31.8 47.8 85.9 25 1
(32) (11/4) 47.8 60.5 76.2 47.8 60.5 82.6 47.8 60.5 82.6 47.8 60.5 82.6 39.6 60.5 88.9 39.6 60.4 88.9 39.6 60.5 104.9 (32) (11/4)
40 11/2 54.1 69.8 85.9 54.1 69.8 95.2 54.1 69.8 95.2 54.1 69.8 95.2 47.8 69.8 98.6 47.8 69.8 98.6 47.8 69.8 117.6 40 11/2
50 2 69.8 85.9 104.9 69.8 85.9 111.3 69.8 85.9 111.2 69.8 85.9 111.3 58.7 85.9 143.0 58.7 85.9 143.0 58.7 85.9 146.0 50 2
65 21/2 82.6 98.6 124.0 82.6 98.6 130.3 82.6 98.6 130.3 82.6 98.6 130.3 69.8 98.6 165.1 69.8 98.6 165.1 69.8 98.6 168.4 65 21/2
80 3 101.6 120.6 136.7 101.6 120.6 149.4 101.6 120.6 149.4 101.6 120.6 149.4 95.2 120.6 168.4 92.2 120.6 174.8 92.2 120.6 196.8 80 3
(90) (31/2) 114.3 133.3 161.9 114.3 133.3 165.1 114.3 133.3 161.9 114.3 133.3 161.9 ─ ─ ─ ─ ─ ─ ─ ─ ─ (90) (31/2)
100 4 127.0 149.4 174.8 127.0 149.4 181.1 120.6 149.4 177.8 120.6 149.4 193.8 120.6 149.4 206.5 117.6 149.6 209.6 117.6 149.4 235.0 100 4
(125) (5) 155.7 177.8 196.8 155.7 177.8 215.9 147.6 177.8 212.9 147.6 177.8 241.3 147.6 177.8 247.6 143.0 177.8 254.0 143.0 177.8 279.4 (125) (5)
150 6 182.6 209.6 222.2 182.6 209.6 251.0 174.8 209.6 247.6 174.8 209.6 266.7 174.8 209.6 289.1 171.4 209.6 282.7 171.4 209.6 317.5 150 6
200 8 233.4 263.7 279.4 233.4 263.7 308.1 225.6 263.7 304.8 225.6 263.7 320.8 222.2 257.3 358.9 215.9 257.3 352.6 215.9 257.3 387.4 200 8
250 10 287.3 317.5 339.9 287.3 317.5 362.0 274.6 317.5 358.9 274.6 317.5 400.0 276.4 311.2 435.1 266.7 311.2 435.1 270.0 311.2 476.2 250 10
300 12 339.9 374.6 409.7 339.9 374.6 422.4 327.2 374.6 419.1 327.2 374.6 457.2 323.8 368.3 498.6 323.8 368.3 520.7 317.5 368.3 549.4 300 12
350 14 371.6 406.4 450.8 371.6 406.4 485.9 362.0 406.4 482.6 362.0 406.4 492.2 355.6 400.0 520.7 362.0 400.0 577.8 ─ ─ ─ 350 14
400 16 422.4 463.6 514.4 422.4 463.6 539.8 412.8 463.6 536.7 412.8 463.6 565.2 412.8 457.2 574.8 406.4 457.2 641.4 ─ ─ ─ 400 16
450 18 474.7 527.0 549.4 474.7 527.0 596.9 469.9 527.0 593.8 469.9 527.0 612.9 463.6 520.7 638.3 463.6 520.7 704.8 ─ ─ ─ 450 18
500 20 525.5 577.8 606.6 525.5 577.8 654.0 520.7 577.8 647.7 520.7 577.8 682.8 520.7 571.5 698.5 514.4 571.5 755.6 ─ ─ ─ 500 20
600 24 628.6 685.8 717.6 628.6 685.8 774.7 628.6 685.8 768.4 628.6 685.8 790.7 628.6 679.4 838.2 616.0 679.4 901.7 ─ ─ ─ 600 24
650 26 673.1 698.5 725.4 673.1 711.2 771.7 666.8 698.5 746.3 663.7 714.5 765.3 692.2 749.3 838.2 ─ ─ ─ ─ ─ ─ 650 26
700 28 723.9 749.3 776.2 723.9 762.0 825.5 714.5 749.3 800.1 704.8 755.6 819.2 743.0 800.1 901.7 ─ ─ ─ ─ ─ ─ 700 28
750 30 774.7 800.1 827.0 774.7 812.8 886.0 765.3 806.4 857.2 778.0 828.8 879.6 806.4 857.2 958.8 ─ ─ ─ ─ ─ ─ 750 30
800 32 825.5 850.9 881.1 825.5 863.6 939.8 812.8 860.6 911.4 831.8 882.6 933.4 863.6 914.4 1,016.0 ─ ─ ─ ─ ─ ─ 800 32
850 34 876.3 908.0 935.0 876.3 914.4 993.9 866.9 911.4 962.2 889.0 939.8 997.0 920.8 971.6 1,073.2 ─ ─ ─ ─ ─ ─ 850 34
900 36 927.1 958.8 987.6 927.1 965.2 1,047.8 917.7 965.2 1,022.4 939.8 990.6 1,047.8 946.2 997.0 1,124.0 ─ ─ ─ ─ ─ ─ 900 36
950 38 974.6 1,009.6 1,044.7 1,009.6 1,047.8 1,098.6 971.6 1,022.4 1,073.2 990.6 1,041.4 1,104.9 1,035.0 1,085.8 1,200.2 ─ ─ ─ ─ ─ ─ 950 38
1,000 40 1,022.4 1,063.8 1,095.5 1,060.4 1,098.6 1,149.6 1,025.6 1,076.4 1,127.2 1,047.8 1,098.6 1,155.7 1,098.6 1,149.4 1,251.0 ─ ─ ─ ─ ─ ─ 1,000 40
1,050 42 1,079.5 1,114.6 1,146.3 1,079.5 1,117.6 1,200.2 1,076.4 1,127.2 1,178.0 1,104.9 1,155.7 1,219.2 1,149.4 1,200.2 1,301.8 ─ ─ ─ ─ ─ ─ 1,050 42
1,100 44 1,124.0 1,165.4 1,197.1 1,162.0 1,200.2 1,251.0 1,130.3 1,181.1 1,231.9 1,162.0 1,212.8 1,270.0 1,206.5 1,257.3 1,368.6 ─ ─ ─ ─ ─ ─ 1,100 44
1,150 46 1,181.1 1,224.0 1,255.8 1,216.2 1,254.2 1,317.8 1,193.8 1,244.6 1,289.0 1,212.8 1,263.6 1,327.2 1,270.0 1,320.8 1,435.1 ─ ─ ─ ─ ─ ─ 1,150 46
1,200 48 1,231.9 1,270.0 1,306.6 1,231.9 1,270.0 1,368.6 1,244.6 1,295.4 1,346.2 1,270.0 1,320.8 1,390.6 1,320.8 1,371.6 1,485.9 ─ ─ ─ ─ ─ ─ 1,200 48
(1,250) (50) 1,282.7 1,325.6 1,357.4 1,317.8 1,355.9 1,419.4 1,295.4 1,346.2 1,403.4 1,320.8 1,371.6 1,447.8 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,250) (50)
(1,300) (52) 1,333.5 1,376.4 1,408.2 1,368.6 1,406.7 1,470.2 1,346.2 1,397.0 1,454.2 1,371.6 1,422.4 1,498.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,300) (52)
1,350 54 1,384.3 1,422.4 1,463.8 1,384.3 1,422.4 1,530.4 1,403.4 1,454.2 1,517.6 1,428.8 1,479.6 1,555.8 ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,350 54
(1,400) (56) 1,435.1 1,470.2 1,514.6 1,479.6 1,524.0 1,593.8 1,454.2 1,505.0 1,568.4 1,479.6 1,530.4 1,612.9 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,400) (56)
(1,450) (58) 1,485.9 1,522.5 1,579.6 1,535.2 1,573.3 1,655.8 1,505.0 1,555.8 1,619.2 1,536.7 1,587.5 1,663.7 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,450) (58)
1,500 60 1,536.7 1,573.3 1,630.4 1,536.7 1,574.8 1,706.6 1,568.4 1,619.2 1,682.8 1,593.8 1,644.6 1,733.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,500 60
Notes: (1) This dimension chart is the same as ASME B16.20-2000 (4) For class 900 and above, please use weld-neck flanges.
except 3-1/2” which is not listed in ASME B16.20-2000. It is (5) For bolting materials, high-tension bolts such as B7 (SNB-7) or ┃Recommended Dimensions for Slip-on Welded Flanges┃ Unit : A
also the same as JPI-7S-41-2005. above are required.
(2) Applicable flanges are ASME B16.5 flanges and ASME (6) With inner and outer rings is recommended for class 900, 1500 and Class 150 Class 300・400・600 Class 900・1500
B16.47 series B flanges. However, these can also be used 2500. Also for 26” and above. Nominal Pipe Size
for JPI-7S-15, JPI-7S-43 series B and API-Std-605 flanges.
(7) Nominal pipe size shown in brackets shall be avoided as much as Gasket inner Gasket outer Outer ring outer Gasket inner Gasket outer Outer ring outer Gasket inner Gasket outer Outer ring outer
(3) Dimensions inside of the bold line are not suitable for slip- possible. diameter diameter diameter diameter diameter diameter diameter diameter diameter
Dimension Charts
Standard
Dimension Charts
20 3/4 29.7 42.9 58.7 29.7 42.9 68.1 29.7 42.9 71.4
25 1 36.5 50.8 68.2 36.5 50.8 74.5 36.5 50.8 80.9
70 71
For ASME B16.5 Flanges Vortex Gasket with Inner and Outer Ring
TM
Class 150 Class 300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Nominal Pipe
Nominal Pipe Size
Inner ring Gasket Gasket outer Outer ring Inner ring Gasket Gasket Outer ring Inner ring Gasket Gasket Outer ring Inner ring Gasket Gasket Outer ring Inner ring Gasket Gasket Outer ring Inner ring Gasket Gasket Outer ring Inner ring Gasket Gasket Outer ring Size
inner inner diameter outer inner inner outer outer inner inner outer outer inner inner outer outer inner inner outer outer inner inner outer outer inner inner outer outer
diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter
A B D1 D2 D3 D4 D1 D2 D3 D4 D1 D2 D3 D4 D1 D2 D3 D4 D1 D2 D3 D4 D1 D2 D3 D4 D1 D2 D3 D4 A B
15 1/2 14.2 19.1 31.8 47.8 14.2 19.1 31.8 54.1 14.2 19.1 31.8 54.1 14.2 19.1 31.8 54.1 14.2 19.1 31.8 63.5 14.2 19.1 31.8 63.5 14.2 19.1 31.8 69.9 15 1/2
20 3/4 20.6 25.4 39.6 57.2 20.6 25.4 39.6 66.8 20.6 25.4 39.6 66.8 20.6 25.4 39.6 66.8 20.6 25.4 39.6 69.9 20.6 25.4 39.6 69.9 20.6 25.4 39.6 76.2 20 3/4
25 1 26.9 31.8 47.8 66.8 26.9 31.8 47.8 73.2 26.9 31.8 47.8 73.2 26.9 31.8 47.8 73.2 26.9 31.8 47.8 79.5 26.9 31.8 47.8 79.5 26.9 31.8 47.8 85.9 25 1
(32) (11/4) 38.1 47.8 60.5 76.2 38.1 47.8 60.5 82.6 38.1 47.8 60.5 82.6 38.1 47.8 60.5 82.6 33.3 39.6 60.5 88.9 33.3 39.6 60.5 88.9 33.3 39.6 60.5 104.9 (32) (11/4)
40 11/2 44.5 54.1 69.9 85.9 44.5 54.1 69.9 95.3 44.5 54.1 69.9 95.3 44.5 54.1 69.9 95.3 41.4 47.8 69.9 98.6 41.4 47.8 69.9 98.6 41.4 47.8 69.9 117.6 40 11/2
50 2 55.6 69.9 85.9 104.9 55.6 69.9 85.9 111.3 55.6 69.9 85.9 111.3 55.6 69.9 85.9 111.3 52.3 58.7 85.9 143.0 52.3 58.7 85.9 143.0 52.3 58.7 85.9 146.1 50 2
65 21/2 66.5 82.6 98.6 124.0 66.5 82.6 98.6 130.3 66.5 82.6 98.6 130.3 66.5 82.6 98.6 130.3 63.5 69.9 98.6 165.1 63.5 69.9 98.6 165.1 63.5 69.9 98.6 168.4 65 21/2
80 3 81.0 101.6 120.7 136.7 81.0 101.6 120.7 149.4 78.7 101.6 120.7 149.4 78.7 101.6 120.7 149.4 78.7 95.3 120.7 168.4 78.7 92.2 120.7 174.8 78.7 92.2 120.7 196.9 80 3
(90) (31/2) 93.7 114.3 133.3 161.9 93.7 114.3 133.3 165.1 93.7 114.3 133.3 161.9 93.7 114.3 133.3 161.9 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ (90) (31/2)
100 4 106.4 127.0 149.4 174.8 106.4 127.0 149.4 181.1 102.6 120.7 149.4 177.8 102.6 120.7 149.4 193.8 102.6 120.7 149.4 206.5 97.8 117.6 149.4 209.6 97.8 117.6 149.4 235.0 100 4
(125) (5) 131.8 155.7 177.8 196.9 131.8 155.7 177.8 215.9 128.3 147.6 177.8 212.9 128.3 147.6 177.8 241.3 128.3 147.6 177.8 247.7 124.5 143.0 177.8 254.0 124.5 143.0 177.8 279.4 (125) (5)
150 6 157.2 182.6 209.6 222.3 157.2 182.6 209.6 251.0 154.9 174.8 209.6 247.7 154.9 174.8 209.6 266.7 154.9 174.8 209.6 289.1 147.3 171.5 209.6 282.7 147.3 171.5 209.6 317.5 150 6
200 8 215.9 233.4 263.7 279.4 215.9 233.4 263.7 308.1 205.7 225.6 263.7 304.8 205.7 225.6 263.7 320.8 196.9 222.3 257.3 358.9 196.9 215.9 257.3 352.6 196.9 215.9 257.3 387.4 200 8
250 10 268.2 287.3 317.5 339.9 268.2 287.3 317.5 362.0 255.3 274.6 317.5 358.9 255.3 274.6 317.5 400.1 246.1 276.4 311.2 435.1 246.1 266.7 311.2 435.1 246.1 270.0 311.2 476.3 250 10
300 12 317.5 339.9 374.7 409.7 317.5 339.9 374.7 422.4 307.3 327.2 374.7 419.1 307.3 327.2 374.7 457.2 292.1 323.9 368.3 498.6 292.1 323.9 368.3 520.7 292.1 317.5 368.3 549.4 300 12
350 14 349.3 371.6 406.4 450.9 349.3 371.6 406.4 485.9 342.9 362.0 406.4 482.6 342.9 362.0 406.4 492.3 320.8 355.6 400.1 520.7 320.8 362.0 400.1 577.9 ─ ─ ─ ─ 350 14
400 16 400.1 422.4 463.6 514.4 400.1 422.4 463.6 539.8 389.9 412.8 463.6 536.7 389.9 412.8 463.6 565.2 374.7 412.8 457.2 574.8 368.3 406.4 457.2 641.4 ─ ─ ─ ─ 400 16
450 18 449.3 474.7 527.1 549.4 449.3 474.7 527.1 596.9 438.2 469.9 527.1 593.9 438.2 469.9 527.1 612.9 425.5 463.6 520.7 638.3 425.5 463.6 520.7 704.9 ─ ─ ─ ─ 450 18
500 20 500.1 525.5 577.9 606.6 500.1 525.5 577.9 654.1 489.0 520.7 577.9 647.7 489.0 520.7 577.9 682.8 482.6 520.7 571.5 698.5 476.3 514.4 571.5 755.7 ─ ─ ─ ─ 500 20
600 24 603.3 628.7 685.8 717.6 603.3 628.7 685.8 774.7 590.6 628.7 685.8 768.4 590.6 628.7 685.8 790.7 590.6 628.7 679.5 838.2 577.9 616.0 679.5 901.7 ─ ─ ─ ─ 600 24
650 26 654.1 673.1 698.5 725.4 654.1 673.1 711.2 771.7 654.1 666.8 698.5 746.3 644.7 663.7 714.5 765.3 666.8 692.2 749.3 838.2 ─ ─ ─ ─ ─ ─ ─ ─ 650 26
700 28 704.9 723.9 749.3 776.2 704.9 723.9 762.0 825.5 701.8 714.5 749.3 800.1 685.8 704.9 755.7 819.2 717.6 743.0 800.1 901.7 ─ ─ ─ ─ ─ ─ ─ ─ 700 28
750 30 755.7 774.7 800.1 827.0 755.7 774.7 812.8 886.0 752.6 765.3 806.5 857.3 752.6 778.0 828.8 879.6 781.1 806.5 857.3 958.9 ─ ─ ─ ─ ─ ─ ─ ─ 750 30
800 32 806.5 825.5 850.9 881.1 806.5 825.5 863.6 939.8 800.1 812.8 860.6 911.4 793.8 831.9 882.7 933.5 838.2 863.6 914.4 1,016.0 ─ ─ ─ ─ ─ ─ ─ ─ 800 32
850 34 857.3 876.3 908.1 935.0 857.3 876.3 914.4 993.9 850.9 866.9 911.4 962.2 850.9 889.0 939.8 997.0 895.4 920.8 971.6 1,073.2 ─ ─ ─ ─ ─ ─ ─ ─ 850 34
900 36 908.1 927.1 958.9 987.6 908.1 927.1 965.2 1,047.8 898.7 917.7 965.2 1,022.4 901.7 939.8 990.6 1,047.8 920.8 946.2 997.0 1,124.0 ─ ─ ─ ─ ─ ─ ─ ─ 900 36
950 38 958.9 974.6 1,009.7 1,044.7 971.6 1,009.7 1,047.8 1,098.6 952.5 971.6 1,022.4 1,073.2 952.5 990.6 1,041.4 1,104.9 1,009.7 1,035.1 1,085.9 1,200.2 ─ ─ ─ ─ ─ ─ ─ ─ 950 38
1,000 40 1,009.7 1,022.4 1,063.8 1,095.5 1,022.4 1,060.5 1,098.6 1,149.4 1,000.3 1,025.7 1,076.5 1,127.3 1,009.7 1,047.8 1,098.6 1,155.7 1,060.5 1,098.6 1,149.4 1,251.0 ─ ─ ─ ─ ─ ─ ─ ─ 1,000 40
1,050 42 1,060.5 1,079.5 1,114.6 1,146.3 1,085.9 1,111.3 1,149.4 1,200.2 1,051.1 1,076.5 1,127.3 1,178.1 1,066.8 1,104.9 1,155.7 1,219.2 1,111.3 1,149.4 1,200.2 1,301.8 ─ ─ ─ ─ ─ ─ ─ ─ 1,050 42
1,100 44 1,111.3 1,124.0 1,165.4 1,197.1 1,124.0 1,162.1 1,200.2 1,251.0 1,104.9 1,130.3 1,181.1 1,231.9 1,111.3 1,162.1 1,212.9 1,270.0 1,155.7 1,206.5 1,257.3 1,368.6 ─ ─ ─ ─ ─ ─ ─ ─ 1,100 44
1,150 46 1,162.1 1,181.1 1,224.0 1,255.8 1,178.1 1,216.2 1,254.3 1,317.8 1,168.4 1,193.8 1,244.6 1,289.1 1,162.1 1,212.9 1,263.7 1,327.2 1,219.2 1,270.0 1,320.8 1,435.1 ─ ─ ─ ─ ─ ─ ─ ─ 1,150 46
1,200 48 1,212.9 1,231.9 1,270.0 1,306.6 1,231.9 1,263.7 1,311.4 1,368.6 1,206.5 1,244.6 1,295.4 1,346.2 1,219.2 1,270.0 1,320.8 1,390.7 1,270.0 1,320.8 1,371.6 1,485.9 ─ ─ ─ ─ ─ ─ ─ ─ 1,200 48
(1,250) (50) 1,263.7 1,282.7 1,325.6 1,357.4 1,267.0 1,317.8 1,355.9 1,419.4 1,257.3 1,295.4 1,346.2 1,403.4 1,270.0 1,320.8 1,371.6 1,447.8 ─ ─ ─ ─ ─ ── ─ ─ ─ ─ ─ (1,250) (50)
(1,300) (52) 1,314.5 1,333.5 1,376.4 1,408.2 1,317.8 1,368.6 1,406.7 1,470.2 1,308.1 1,346.2 1,397.0 1,454.2 1,320.8 1,371.6 1,422.4 1,498.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,300) (52)
1,350 54 1,365.3 1,384.3 1,422.4 1,463.8 1,365.3 1,403.4 1,454.2 1,530.4 1,352.6 1,403.4 1,454.2 1,517.7 1,378.0 1,428.8 1,479.6 1,555.8 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,350 54
(1,400) (56) 1,422.4 1,444.8 1,477.8 1,514.6 1,428.8 1,479.6 1,524.0 1,593.9 1,403.4 1,454.2 1,505.0 1,568.5 1,428.8 1,479.6 1,530.4 1,612.9 ─ ─ ─ ─ ── ─ ─ ─ ─ ─ ─ (1,400) (56)
(1,450) (58) 1,478.0 1,500.4 1,528.8 1,579.6 1,484.4 1,535.2 1,573.3 1,655.8 1,454.2 1,505.0 1,555.8 1,619.3 1,473.2 1,536.7 1,587.5 1,663.7 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,450) (58)
1,500 60 1,535.2 1,557.3 1,586.0 1,630.4 1,557.3 1,589.0 1,630.4 1,706.6 1,517.7 1,568.5 1,619.3 1,682.8 1,530.4 1,593.9 1,644.7 1,733.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,500 60
Notes: (1) This dimension chart is the same as ASME B16.20-1998 (5) For bolting materials, high-tension bolts such as B7 (SNB-7) or
except 3-1/2” which is not listed in ASME B16.20-1998. It is
also the same as JPI-7S-41-2005.
above are required.
┃Recommended Dimensions for Slip-on Welded Flanges┃ Unit : A
(6) When used for slip-on flanges, please pay attention to the
(2) Applicable flanges are ASME B16.5 flanges and ASME dimensions since the inner diameter of inner ring may be smaller
Class 150 Class 300・400・600 Class 900・1500
B16.47 series B flanges. However, these can also be used than the flange inner diameter. To avoid this kind of problem, weld-
Nominal Pipe Size
for JPI-7S-15, JPI-7S-43 series B and API-Std-605 flanges. neck flanges are recommended. Inner ring Gasket Gasket Outer ring Inner ring Gasket Gasket Outer ring Inner ring Gasket Gasket Outer ring
(3) Dimensions inside of the bold line are not suitable for slip- (7) The gasket outer diameter for the types inner ring indicates the inner inner outer outer inner inner outer outer inner inner outer outer
on welded flanges. Use weld-neck flanges or socket-welded shoulder dimensions of the gasket excluding spring layers. diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter diameter
flanges. If slip-on flanges are used, gaskets as per
A B D1 D2 D3 D4 D1 D2 D3 D4 D1 D2 D3 D4
Dimension Charts
Standard
Dimension Charts
25 1 30.0 36.5 50.8 68.2 30.0 36.5 50.8 74.5 30.0 36.5 50.8 80.9
72 73
For ASME B16.47 Series A Flanges Vortex Gasket with Inner and Outer Ring
TM
Notes: (1) This dimension chart is the same as the dimensions of (3) Please use weld-neck flanges.
ASME B16.20-1998. (4) The gasket outer diameter for the types inner ring indicates the
Standard
(2) Applicable flanges are ANSI/ASME B16.47 Series A and shoulder dimensions of the gasket excluding spring layers.
MSS-SP-44 flanges. This can also be used for JPI-7S-43
Series A flanges.
74
For ASME B16.5 Flanges
For JPI-7S-15 Flanges Vortex Gasket Standard Type/ With Inner Ring Type
TM
Notes: (1) *Small: For small male & female faces or small tongue & (7) For small M&F faces, with inner ring type is recommended
groove face flanges. irrespective of the filler material.
*Large: For large male & female faces or large tongue & (8) For bolting materials, high-tension bolts such as B7 (SNB7) or above
groove face flanges. are required.
(2) Applicable flanges are ASME B16.5 and JPI-7S-15.
Depth of the face is preferably more than 5.5A.
(3) No large M&F and large T&G face are stipulated for class
150 flanges.
(4) For small M&F and small T&G faces, Vortex gaskets are not
advisable due to its narrow gasket width. This chart is
merely for reference.
(5) The dimensions for large M&F and large T&G faces in this
chart are the same as JPI-7S-41-90. The dimensions for
small M&F and small T&G faces are the same as the
dimensions shown in commentary part of JPI-7S-41-85.
(6) For large M&F faces of class 900 and above, with inner ring
type is recommended irrespective of the filler material.
Dimension Charts
Standard
75
For Taylor Forge and Vortex Gasket with Inner and Outer Ring
TM
Ladish Flanges
28 711 731 754 791 711 731 763 803 701 726 776 831 701 726 776 895
30 762 782 809 848 762 782 814 860 752 777 827 882 752 777 827 952
32 813 833 860 899 813 833 865 911 803 828 878 939 803 828 878 1,009
34 864 884 915 952 864 884 916 962 854 879 929 990 854 879 929 1,060
36 914 934 965 1,003 914 934 966 1,026 904 929 979 1,047 904 929 979 1,117
38 965 985 1,016 1,054 965 985 1,017 1,076 955 985 1,035 1,111 955 985 1,035 1,168
40 1,016 1,041 1,074 1,105 1,016 1,041 1,081 1,127 1,006 1,036 1,086 1,162 1,006 1,036 1,086 1,225
42 1,067 1,092 1,130 1,165 1,067 1,092 1,132 1,184 1,057 1,087 1,137 1,219 1,057 1,087 1,137 1,289
44 1,118 1,143 1,181 1,216 1,118 1,143 1,183 1,245 1,108 1,138 1,188 1,276 1,108 1,138 1,188 1,346
46 1,168 1,193 1,231 1,267 1,168 1,193 1,233 1,295 1,158 1,188 1,238 1,327 1,158 1,188 1,238 1,403
48 1,219 1,244 1,282 1,318 1,219 1,244 1,284 1,346 1,209 1,239 1,289 1,384 1,209 1,239 1,289 1,492
52 1,321 1,346 1,386 1,426 1,321 1,351 1,401 1,457 1,311 1,341 1,391 1,492 ─ ─ ─ ─
54 1,372 1,397 1,437 1,476 1,372 1,402 1,452 1,508 1,362 1,392 1,442 1,549 ─ ─ ─ ─
60 1,524 1,549 1,589 1,629 1,524 1,554 1,604 1,661 1,514 1,544 1,594 1,714 ─ ─ ─ ─
66 1,676 1,706 1,746 1,781 1,702 1,742 1,782 1,842 1,745 1,785 1,825 1,885 ─ ─ ─ ─
72 1,829 1,859 1,899 1,946 1,854 1,894 1,934 1,994 1,911 1,951 1,991 2,051 ─ ─ ─ ─
84 2,162 2,202 2,232 2,292 2,197 2,237 2,267 2,327 2,244 2,284 2,314 2,374 ─ ─ ─ ─
96 2,467 2,507 2,537 2,597 2,512 2,552 2,582 2,642 2,568 2,608 2,638 2,698 ─ ─ ─ ─
Notes: (1) Applicable flanges are Taylor Forge Class 175, 350, 125 and 250, Ladish Class 150 and 300.
For Taylor Forge Class 150, please use Standard Dimension Chart 8.
(2) These dimension were designed by NICHIAS Corporation.
(3) Gaskets with inner and outer rings are recommended for all nominal pressures.
(4) For bolting materials, high-tension bolts such as B7 (SNB-7) or above are required.
Dimension Charts
Standard
Dimension Charts
Standard
76 77
Ring Joint Gaskets R Rings
Gasket Dimensions
Oval type Octagonal type
Pitch diameter Width of flat on
Ring Number Height of ring T
of ring Width of ring Octagonal Ring
P W Oval Octagonal A
Dimension Charts
Standard
Dimension Charts
API Spec. 6A
R-50 269.88 15.88 22.4 20.6 10.49
MSS SP-44
R-51 279.40 22.22 28.4 26.9 14.81
JPI-7S-43
R-52 304.80 7.92 14.2 12.7 5.23
Standard
JPI-7S-15
78 79
Ring Joint Gaskets API RX Rings
Dimension Tolerance
+0.50
OD
−0.00
+0.20
A,H
−0.00
+0.15
C
−0.00
+0.00
D
−0.80
R1 ±0.50
Notes: (1) This dimension chart is the same as the dimensions of API-Spec. hole as illustrated. The centerline of the hole shall be located at the midpoint
6A RX Pressure Energized Ring Joint Gaskets. of dimension C
Standard
(2) Applicable flanges are API-Spec. 6A Wellhead Equipment 6B (4) The finish of the seal surface of the gaskets is over 63RMS.
Flanges.
* 1 Dimensional tolerance +0, -0.38 * 2 Dimensional tolerance +0.5, -0
(3) Rings RX-82 through RX-91 only require one pressure passage
80
Ring Joint Gaskets API BX Rings
Dimension Tolerance
+0.50
OD
−0.15
+0.20
H,A
−0
ODT ±0.05
−0
+0.15
C
−0
+0.50
E
−0
+0.10
G.N
−0.0
BX-150 72.19 9.30 9.30 70.87 7.98 1.59 5.56 73.48 11.43
BX-151 76.40 9.63 9.63 75.03 8.26 1.59 5.56 77.79 11.84
BX-152 84.68 10.24 10.24 83.24 8.79 1.59 5.95 86.23 12.65
BX-153 100.94 11.38 11.38 99.31 9.78 1.59 6.75 102.77 14.07
BX-154 116.84 12.40 12.40 115.09 10.64 1.59 7.54 119.00 15.39
Radius R shall be 8 ∼12% of gasket height H
BX-155 147.96 14.22 14.22 145.95 12.22 1.59 8.33 150.62 17.73
BX-169 173.51 15.85 12.93 171.27 10.69 1.59 9.53 176.66 16.92
BX-156 237.92 18.62 18.62 235.28 15.98 3.18 11.11 241.83 23.39
BX-157 294.46 20.98 20.98 291.49 18.01 3.18 12.70 299.06 26.39
BX-158 352.04 23.14 23.14 348.77 19.86 3.18 14.29 357.23 29.18
BX-159 426.72 25.70 25.70 423.09 22.07 3.18 15.88 432.64 32.49
BX-160 402.59 23.83 13.74 399.21 10.36 3.18 14.29 408.00 19.96
BX-161 491.41 28.07 16.21 487.45 12.24 3.18 17.07 497.94 23.62
BX-162 475.49 14.22 14.22 473.48 12.22 1.59 8.33 478.33 17.91
BX-163 556.16 30.10 17.37 551.89 13.11 3.18 18.26 563.50 25.55
BX-164 570.56 30.10 24.59 566.29 20.32 3.18 18.26 577.90 32.77
BX-165 624.71 32.03 18.49 620.19 13.97 3.18 19.05 632.56 27.20
BX-166 640.03 32.03 26.14 635.51 21.62 3.18 19.05 647.88 34.87
BX-167 759.36 35.87 13.11 754.28 8.03 1.59 21.43 768.33 22.91
BX-168 765.25 35.87 16.05 760.17 10.97 1.59 21.43 774.22 25.86
Notes: (1) This dimension chart is the same as the dimensions of API-Spec. 6A 1977 BX Pressure Energized Ring-Joint Gaskets.
(2) Applicable flanges are API-Spec. 6A Wellhead Equipment 6BX Flanges.
(3) One pressure passage hole is required per gasket as illustrated.
The centerline of the hole shall be located at the midpoint of dimension C
(4) The finish of the seal surface of the gaskets is over 32RMS.
Dimension Charts
Standard
81
Ring Joint Gaskets Correspondence of ring number, flange NPS and class
Octagonal type
Oval type
TOMBO No.1850-C
TOMBO No.1850-V
Applicable flanges
Nominal
Pipe JPI - 7 - 15, ANSI B 16.5 API Spec 6A MSS SP - 44
Size
Class 150 300・400・600 900 1500 2500 960 2000 3000 5000 300・400・600 900
82
For ASME B16.5 Flanges NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-A/B)
TM Ñ
1/2 17 24 ─ ─ 36 47 36 53
3/4 22 29 ─ ─ 44 56 44 66
1 28 35 ─ ─ 52 66 52 72
11/4 36 43 ─ ─ 65 75 65 82
11/2 42 49 ─ ─ 74 85 74 94
2 53 60 ─ ─ 92 104 92 110
21/2 66 73 ─ ─ 105 123 105 129
3 90 97 ─ ─ 127 135 127 148
31/2 103 110 ─ ─ 140 161 140 164
4 116 123 ─ ─ 157 173 157 180 3.2
A Type
5 143 150 ─ ─ 186 196 186 215 (2.8)
Notes: (1) Dimensions for class 150 up to 24” are same as JPI-7S-15- (3) Dimensions in brackets are for TOMBO No.9010-NA-A-5/-NA-A-7 and
1999. TOMBO No.9010-NA-B-5/-NA-B-7.
Other dimensions are designed by NICHIAS Corporation to (4) For slip-on flanges, gaskets for 1/2” to 2-1/2” cannot be used since
fit to the applicable flanges. the gasket I.D. (D1) is smaller than the flange I.D.
(2) Applicable flanges are ASME B16.5, ASME B16.47 Series B,
API 605, JPI-7S-15 and JPI-7S-43.
83
For ASME B16.47 Series A Flanges
For MSS SP-44 Flanges NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-B)
TM Ñ
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B16.47 Series A and MSS SP-44 flanges.
(3) Dimensions in brackets are for TOMBO No.9010-NA-B-5/-NA-B-7.
Dimension Charts
Standard
84
For ASME B16.1 Flanges NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-B)
TM Ñ
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B 16.1-1998 and Taylor Forge Flanges.
☆ marked sizes are for Taylor Forge flanges
(3) Dimensions in brackets are for TOMBO No.9010-NA-B-5/-NA-B-7.
Dimension Charts
Standard
85
For ASME B16.5 Flanges NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-AS)
TM Ñ
15 1/2 21 24 47 47 36 53
20 3/4 26 29 56 56 44 66
2.5 2.5
25 1 32 35 66 66 52 72
(2.8) (2.5)
32 11/4 40 43 75 75 65 82
40 11/2 46 49 85 85 74 94
50 2 57 60 92 104 92 110
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B 16.5 and JPI-7S-15.
(3) Dimensions in brackets are for TOMBO No.9010-NA-AS-5/-NA-AS-7.
Dimension Charts
Standard
86
For ASME B16.5 Flanges NAFLON PTFE Cushion Gasket
TM
O.D
I.D
T
t
D1
D2
D3
D4
A Type
15 1/2 17 25 47 47 26 36 47 53 26 36
20 3/4 22 30 56 56 31 42 56 66 31 42
25 1 28 36 66 66 38 50 66 72 38 50
32 11/4 36 44 75 75 49 63 75 82 49 63
40 11/2 42 50 85 85 55 72 85 94 55 72
50 2 53 61 92 104 70 90 92 110 70 90
90 31/2 103 111 140 161 118 138 140 164 118 138
100 4 116 124 157 173 136 155 157 180 136 155
2.0 3.9 A Type
125 5 143 151 186 196 164 184 186 215 164 184
150 6 169 177 216 221 194 214 216 250 194 214
200 8 220 228 270 277 242 268 270 306 242 268
250 10 275 283 324 338 290 322 324 360 290 322
300 12 326 334 381 408 347 379 381 420 347 379
350 14 358 365 413 449 377 411 413 484 377 411
400 16 408 416 470 512 432 468 470 538 432 468
450 18 459 467 533 547 487 531 533 595 487 531
500 20 510 518 584 604 537 582 584 651 537 582
600 24 612 620 692 715 637 690 692 772 637 690
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B 16.5 and JPI-7S-15
(3) For slip-on flanges, gaskets for 1/2” to 2-1/2” cannot be used since the gasket I.D. (D1) is
smaller than the flange I.D.
Dimension Charts
Standard
87
For NAFLON Lined Piping TM
NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-FG-7)
TM Ñ
15 1/2 16 47 56
20 3/4 22 56 1 AS-728
Type
25 1 28 66 66
40 11/4 45 85 40
Notes: (1) TOMBO No.9010-NA-FG-7 is a PTFE jacket type gasket used for anti-corrosion NAFLON
lined piping.
If a solid type product is required, please use the TOMBO No.9007 NAFLON PTFE cut
gasket or TOMBO No.9007-LC NAFLON Low creap gasket.
For D1, D4 and t, follow same dimensions as above chart.
(2) Applicable flanges are flanges for fluoro-piping, 1/2” to 12” Class 150
88
For ASME B16.5 Flanges Ebilon GasketTM
15 1/2 86 18 5 30 ─ 60 4-16 42
20 3/4 96 22 5 30 42 70 4-16 52
25 1 105 29 5 37 50 79 4-16 60
Notes: (1) Applicable gaskets are Ebilon Gaskets TOMBO No.9013, 9013-D, 9013-EP and 9013-DEP.
(2) These gasket dimensions are designed by NICHIAS Corporation to fit to weld-neck flanges of JPI-7S-15-85.
(3) Applicable flanges are weld-neck flanges and socket-welded flanges of JPI-7S-15-85. It is also used for ASME B 16.5 flanges.
Dimension Charts
Standard
89
FOR ASME / JPI Class 150 Flanges Electrical Insulation Bolt Kit
(TOMBO No.9910/9910H, TOMBO No.9011-NA-E5)
Ñ Ñ
Metal Insulation
t t3
d3
d1 d1 D5
d2 D2 d2 D2
rs t3
L d3
H t2 t1 D5
*Applicable flange: ASME B 16.5 (Class 150 and 300), JPI-75-15-81(Class 150 and 300).
*The inner diameter of gasket is the same as that of STPG sch40 steel pipe for up to nominal size of 12B, the same as or 4mm smaller than that of STPG sch20 steel
pipe.
*The size of TOMBO No.9910 is the same as that of TOMBO No.9910-H except for "t" that stands for the thickness of insulating sleeve.
*If service temperature is over 150℃, TOMBO No.9910-H/9007-LC should be used. Please consult with us about the size of the TOMBO No.9007-LC.
Dimension Charts
Standard
90
FOR ASME / JPI Class 300 Flanges Electrical Insulation Bolt Kit
(TOMBO No.9910/9910H, TOMBO No.9011-NA-ES) Ñ Ñ
Metal Insulation
t t3
d3
d1 d1 D5
d2 D2 d2 D2
rs t3
L d3
H t2 t1 D5
*The inner diameter of gasket is the same as that of STPG sch40 steel pipe for up to nominal size of 12B, the same as or 4mm smaller than that of STPG sch20 steel
pipe.
*Please let us know if whitworth screw thread is used.
*The size of TOMBO No.9910 is the same as that of TOMBO No.9910-H except for "t" that stands for the thickness of insulating sleeve.
*If service temperature is over 150℃, TOMBO No.9910-H/9007-LC should be used. Please consult with us about the size of the TOMBO No.9007-LC.
Dimension Charts
Standard
91
For JIS Flanges Soft Gasket, Flat Ring Gasket
10A 18 ─ 45 53 55 53 53 59 59 64
15 22 ─ 50 58 60 58 58 64 64 69
20 28 ─ 55 63 65 63 63 69 69 75
25 35 ─ 65 74 78 74 74 79 79 80
32 43 ─ 78 84 88 84 84 89 89 90
40 49 ─ 83 89 93 89 89 100 100 108
50 61 ─ 93 104 108 104 104 114 114 125
84
65 〔77〕 ─ 118 124 128 124 124 140 140 153
80 90 ─ 129 134 138 140 140 150 150 163
90 102 ─ 139 144 148 150 150 163 163 181
100 115 ─ 149 159 163 165 165 173 183 196
125 141 ─ 184 190 194 203 203 208 226 235
150 167 ─ 214 220 224 238 238 251 265 275
175 192 ─ 240 245 249 ─ ─ ─ ─ ─
200 218 ─ 260 270 274 283 283 296 315 330
225 244 ─ 285 290 294 ─ ─ ─ ─ ─
250 270 ─ 325 333 335 356 356 360 380 394
300 321 ─ 370 378 380 406 406 420 434 449
350 359 ─ 413 423 425 450 450 465 479 488
400 410 ─ 473 486 488 510 510 524 534 548
450 460 535 533 541 ─ 575 575 ─ ─ ─
500 513 585 583 596 ─ 630 630 ─ ─ ─
550 564 643 641 650 ─ 684 684 ─ ─ ─
600 615 693 691 700 ─ 734 734 ─ ─ ─
650 667 748 746 750 ─ 784 805 ─ ─ ─
700 718 798 796 810 ─ 836 855 ─ ─ ─
750 770 856 850 870 ─ 896 918 ─ ─ ─
800 820 906 900 920 ─ 945 978 ─ ─ ─
850 872 956 950 970 ─ 995 1,038 ─ ─ ─
900 923 1,006 1,000 1,020 ─ 1,045 1,088 ─ ─ ─
1,000 1,025 1,106 1,100 1,124 ─ 1,158 ─ ─ ─ ─
1,100 1,130 1,216 1,210 1,234 ─ 1,258 ─ ─ ─ ─
1,200 1,230 1,326 1,320 1,344 ─ 1,368 ─ ─ ─ ─
1,300 1,335 ─ ─ ─ ─ 1,474 ─ ─ ─ ─
1,350 1,385 1,481 1,475 1,498 ─ 1,534 ─ ─ ─ ─
1,400 1,435 ─ ─ ─ ─ 1,584 ─ ─ ─ ─
1,500 1,540 1,636 1,630 1,658 ─ 1,694 ─ ─ ─ ─
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, cloth (3) Applicable flanges are those specified in the following standards.
reinforced rubber cut gaskets, Graseal gaskets and PTFE cut JIS B2220-2004 “Steel welding pipe flanges“
gaskets. JIS B2239-2004 “Cast iron pipe flanges“
(2) This dimension chart is the same as the dimensions shown below. JIS B2240-2006 “General rulus for copper alloy pipe flanges“
JIS B2404-2666 “Dimensions of gaskets for use with pipe flange“ JIS B2241-2006 “Basic dimensions of aluminum alloy pipe flanges“
Dimension Charts
Standard
reference, table 4. JIS B2240-1996 “General rules for copper alloy pipe flanges“
But, dimensions below〔 〕and one for 2K,40K and 63K which are JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
Not specified by the above standard are as per JIS B2404-1999
(4) Joint sheets, Graseal gaskets and PTFE cut gaskets are not recommended
“Dimensions of gaskets for use with pipe flange“ reference, table 7. for nominal pressures of 2K and 5K.
(5) For nominal pressure of 30K and above, soft gaskets are not recommended.
93
For JIS Flanges Soft Gasket/Full Face Gasket (F.F.)
Nominal Gasket Gasket Bolt Gasket Bolt Gasket Bolt Gasket Bolt
inner outer circle outer circle outer circle outer circle
Pipe Size n×h n×h n×h n×h
diameter diameter diameter diameter diameter diameter diameter diameter diameter
D1 D2 C D2 C D2 C D2 C
(4) Joint sheets, Graseal gaskets and PTFE cut gaskets are not recommended for
nominal pressures of 2K and 5K.
Even 10K and 16K full face gaskets are not suitable for gas sealing due to
insufficient seating stress.
94
For JIS, M&F, T&G Flanges Soft Gasket
Nominal Pipe Size Gasket inner Gasket outer Gasket inner Gasket outer
diameter diameter diameter diameter
D1 D2 D1 D2
10A 18 38 28 38
15 22 42 32 42
20 28 50 38 50
25 35 60 45 60
32 43 70 55 70
40 49 75 60 75
50 61 90 70 90
65 77 110 90 110
80 90 120 100 120
90 102 130 110 130
100 115 145 125 145
125 141 175 150 175
150 167 215 190 215
200 218 260 230 260
250 270 325 295 325
300 321 375 340 375
350 359 415 380 415
400 410 475 440 475
450 460 523 483 523
500 513 575 535 575
550 564 625 585 625
600 615 675 635 675
650 667 727 682 727
700 718 777 732 777
750 770 832 787 832
800 820 882 837 882
850 872 934 889 934
900 923 987 937 987
1,000 1,025 1,092 1,042 1,092
1,100 1,130 1,192 1,142 1,192
1,200 1,230 1,292 1,237 1,292
1,300 1,335 1,392 1,337 1,392
1,350 1,385 1,442 1,387 1,442
1,400 1,435 1,492 1,437 1,492
1,500 1,540 1,592 1,537 1,592
Notes: (1) The materials used are mainly joint sheet, Graseal, and PTFE cut gaskets.
(2) This dimension chart is the same as the dimensions shown below.
JIS B 2404-2006 “Dimensions of gaskets for pipe flanges” Chart-5
(3) Applicable flanges are those specified in the following standards.
Dimension Charts
Standard
95
For JIS Flanges Vortex Gasket with Outer Ring
TM
Notes: (1) This dimension chart is the same as the dimensions shown below. (3) For the 30K A and B type slip-on welded flanges, please use the dimensions
JIS B 2404-1999 “Dimension of gaskets for pipe flanges” Chart 12 ~ 16 shown on Page 96. Dimension Charts 28 & 29
(2) Applicable flanges are those specified in the following standards. (4) For flanges with a nominal pressure of 63K, Vortex gaskets with inner and outer
rings are recommended.
JIS B2220-2004 “Steel welding pipe flanges“
(5) For Graseal and Naflon Vortex gaskets, those with inner and outer ring type are
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued) recommended.
JIS B2239-1996 “General rules for cast iron pipe flanges“ (Discontinued) (6) For 2K and 5K flanges, Vortex gaskets are not recommended.
However, the dimensions of 10K, 16K and 20K cannot be used for (7) For bolting material, high-tension bolts such as B7 (SNB7) and above are required.
small raised face gaskets.
(8) The gasket outer diameter for the types with outer ring indicates the shoulder
In the case of the dimensions of 30K, a nominal size of 50A and under dimensions of the gasket excluding spring layers.
can only be used for large raised face gaskets. 65A and over can be
Dimension Charts
used for both large and small raised face gaskets, but these are only
applicable for weld-neck (butt-welded) flanges and C type slip-on
welded flanges as specified in JIS B 2220. The dimensions of 40K and
Standard
63K are suitable for large and small raised face gaskets, but these are
only applicable for weld-neck flanges and C type slip-on welded flanges
as specified in JIS B 2220.
96
For JIS Flanges Vortex Gasket with Outer and Inner Ring
TM
Notes: (1) This dimension chart is the same as the dimensions shown For 40K and 63K, applicable for large and small raised face, but
below. limited to only weld-neck flanges and C type slip-on flanges as per
JIS B 2404-1999 “Dimensions of gaskets for pipe flanges” JIS B 2220.
Chart 17 ~ 20 (3) For 30K A and B type slip-on flanges, use the dimensions shown on
(2) Applicable flanges are those specified in the following Page 35. Dimension Charts 28 & 29
standards. (4) For bolting material, high-tension bolts such as B7 (SNB7) and above
Applicable flanges: are required.
JIS B2220-2004 “Steel welding pipe flanges“ (5) The gasket outer diameter for the types with outer ring indicates the
shoulder dimensions of the gasket excluding spring layers.
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
JIS B2239-1996 “General rules for cast iron pipe flanges“ (Discontinued)
For 16K and 20K, these dimensions cannot be used for small
Dimension Charts
Standard
97
For JIS Large Flanges Vortex Gasket with Outer and Inner Ring
TM
For Slip-on Welded Flange A Type For Slip-on Welded Flange B Type
Vortex Gasket with Outer and Inner Ring Vortex Gasket with Outer and Inner Ring
Dimension Chart 30 Unit : A Dimension Chart 31 Unit : A
10A 28 38 25 38 19 25 38
15 32 42 29 42 23 29 42
20 38 50 37 50 31 37 50
25 45 60 44 60 38 44 60
32 55 70 54 70 46 54 70
40 60 75 59 75 51 59 75
50 70 90 70 90 62 70 90
Notes: (1) This dimension chart is the same as the dimensions shown (3) When a Vortex gasket with inner ring is used for slip-on flange, please
below. pay attention to the dimensions since the inner diameter of inner ring
JIS B 2404-2006 “Dimensions of gaskets for pipe flanges” is small than the flange inner diameter.
Chart 11 ~ 13 (4) For bolting material, high-tension bolts such as B7 (SNB7) and above
(2) Applicable flanges are Tongue & Groove and Male & Female are required.
flanges specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“
(Discontinued)
Dimension Charts
Standard
99
For JIS Flanges NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-A/B)
TM Ñ
10 3/8 18 26 42 45 49 53 48 53 49 53
15 1/2 22 30 46 50 54 58 52 58 54 58
20 3/4 28 36 52 55 59 63 58 63 59 63
25 1 35 43 59 65 70 74 70 74 70 74
32 11/4 43 51 71 78 79 84 79 84 79 84
40 11/2 49 57 77 83 84 89 85 89 85 89
50 2 62 69 88 93 99 104 100 104 99 104
65 21/2 78 85 106 118 119 124 116 124 119 124
80 3 91 98 121 129 129 134 135 140 135 140
90 31/2 104 111 134 139 140 144 145 150 148 150
100 4 117 124 145 149 155 159 160 165 163 165
125 5 144 151 178 184 185 190 195 203 198 203 3.2
A Type
150 6 171 178 205 214 215 220 227 238 233 238 (2.8)
175 7 193 200 229 240 240 245 ─ ─ ─ ─
200 8 219 226 255 260 265 270 275 283 278 283
225 9 244 251 280 285 285 290 ─ ─ ─ ─
250 10 271 278 313 325 321 333 345 356 345 356
300 12 321 328 363 370 370 378 395 406 395 406
350 14 356 363 401 413 415 423 436 450 436 450
400 16 407 414 461 473 471 486 487 510 487 510
450 18 457 464 511 533 530 541 556 575 565 575
500 20 510 517 571 583 583 596 609 630 609 630
550 22 561 568 625 641 635 650 665 684 665 684
600 24 612 619 676 691 684 700 716 734 716 734
650 26 670 674 735 746 740 750 770 784 790 805
700 28 725 729 785 796 800 810 820 836 840 855
750 30 775 779 840 850 855 870 880 896 900 918 3.2
800 32 825 829 890 900 905 920 930 945 960 978 (3.8)
850 34 875 879 940 950 955 970 980 995 1,020 1,038
900 36 925 929 990 1,000 1,005 1,020 1,030 1,045 1,070 1,088
1,000 40 1,030 1,034 1,090 1,100 1,110 1,124 1,140 1,158 ─ ─ B Type
1,100 44 1,130 1,134 1,200 1,210 1,220 1,234 1,240 1,258 ─ ─
1,200 48 1,230 1,234 1,305 1,320 1,325 1,344 1,350 1,368 ─ ─
5.0
1,300 52 1,335 1,339 ─ ─ ─ ─ 1,450 1,474 ─ ─
(3.8)
1,350 54 1,390 1,394 1,460 1,475 1,480 1,498 1,510 1,534 ─ ─
1,400 56 1,435 1,439 ─ ─ ─ ─ 1,560 1,584 ─ ─
1,500 60 1,545 1,549 1,615 1,630 1,635 1,658 1,670 1,694 ─ ─
Dimension Charts
Notes: (1) These dimensions were designed by NICHIAS Corporation to JIS B2238-1996 “General rules for steel welding pipe flanges“
fit to JIS B 2238-1996 flanges. (Discontinued)
Standard
(2) Applicable flanges are those specified in the following standards. (3) Dimensions in brackets are applicable for TOMBO No.9010-NA-A-5/-
JIS B2220-2004 “Steel welding pipe flanges“ NA-A-7 and TOMBO No.9010-NA-B-5/-NA-B-7 type.
JIS B2239-2004 “Cast iron pipe flanges“ (4) For B type slip-on flanges as per JIS B 2220, nominal pressure of
JIS B2240-1996 “General rules for copper alloy pipe flanges“ 20K, nominal size of 10~50A gaskets with these dimensions cannot
be used.
JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
100
For JIS Flanges NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-AS)
TM Ñ
10 3/8 26 28 42 45 48 53 48 53
15 1/2 31 33 48 50 52 58 52 58
20 3/4 36 38 52 55 58 63 58 63 2.5
25 1 41 43 62 65 70 74 70 74 (2.5)
32 11/4 51 53 72 78 80 84 80 84
40 11/2 56 58 78 83 85 89 85 89
50 2 67 70 88 93 100 104 100 104
65 21/2 92 95 112 118 120 124 120 124
80 3 102 105 125 129 130 134 135 140
90 31/2 112 115 135 139 140 144 145 150
100 4 122 125 145 149 155 159 160 165
125 5 152 155 180 184 185 190 195 203
AS Type
150 6 187 190 210 214 215 220 230 238
175 7 207 210 235 240 240 245 ─ ─
200 8 232 235 255 260 265 270 275 283 3.4
225 9 257 260 280 285 285 290 ─ ─ (3.0)
250 10 297 300 320 325 325 333 345 356
300 12 337 340 365 370 370 378 395 406
350 14 377 380 405 413 415 423 440 450
400 16 427 430 465 473 475 486 495 510
450 18 477 480 525 533 530 541 560 575
500 20 527 530 575 583 585 596 615 630
550 22 577 580 630 641 640 650 670 684
600 24 627 630 680 691 690 700 720 734
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2239-2004 “Cast iron pipe flanges“
JIS B2240-1996 “General rules for copper alloy pipe flanges“
JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(3) Dimensions in brackets are applicable for TOMBO No.9010-NA-AS-5/-NA-AS-7.
(4) For B type slip-on flanges as per JIS B 2220, nominal pressure of 20K, nominal size of 10~50A gaskets with these dimensions cannot be
used since inner diameter of gasket is smaller than flange inner diameter.
Dimension Charts
Standard
101
NAFLON PTFE Cushion Gasket
TM
O.D
I.D
T
t
D1
D2
D3
D4
A Type
(10) 3/8 18 26 49 53 30 47 49 53 30 47
(15) 1/2 22 30 54 58 34 52 54 58 34 52
(20) 3/4 28 36 59 63 40 57 59 63 40 57
25 1 35 43 70 74 47 68 70 74 47 68
32 11/4 43 51 79 84 55 77 79 84 55 77
40 11/2 49 57 85 89 61 83 85 89 61 83
50 2 61 69 99 104 73 97 99 104 73 97
90 31/2 103 111 140 144 115 138 148 150 115 146
100 4 116 124 155 159 128 153 163 165 128 161
125 5 143 151 185 190 155 183 198 203 155 196
A
2.0 3.9
150 6 170 178 215 220 182 213 233 238 182 231 Type
200 8 218 226 265 270 230 263 278 283 230 276
250 10 270 278 321 333 282 319 345 356 282 343
300 12 320 328 370 378 332 368 395 406 332 393
350 14 355 363 415 423 367 413 436 450 367 434
400 16 406 414 471 486 418 469 487 510 418 485
450 18 456 464 530 541 468 528 556 575 468 554
500 20 509 517 583 596 521 581 609 630 521 607
550 22 560 568 635 650 572 633 665 684 572 663
600 24 611 619 684 700 623 682 716 734 623 714
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.
Dimension Charts
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(3) These gaskets cannot be used for the following services since inner diameter of gasket is smaller
than flange inner diameter.
Slip-on flanges as per JIS B 2220, 10K, 16K and 20K for 10~40A
Slip-on flanges as per JIS B 2220, 20K and 30K for 10~65A
102
For NAFLON Lined Piping TM
NAFLON PTFE Cushion Gasket (TOMBO No.9010-NA-FG-7)
TM Ñ
15 1/2 16 58
40 11/2 45 89
50 2 58 104
65 21/2 71 124
Notes: (1) TOMBO No.9010-NA-FG-7 is a PTFE jacket type gasket used for anti-corrosion NAFLON lined piping.
If a solid type product is required, please use the TOMBO No.9007 NAFLON PTFE cut gasket or TOMBO No.9007-LC
NAFLON Low creap gasket.
For D1, D4 and t, follow same dimensions as above chart.
(2) Applicable flanges are JIS 10K flanges for NAFLON lined piping, 15A-300A
103
For JIS Flanges NAFLON PTFE Cushion Gasket (Outer periphery seald)
TM
(TOMBO No.9010-NA-R-A)
Ñ
D2 D2
D1 D1
t2 t1 t2 t1
D3 D3
D4 D4
Nominal D3 D4
Pipe Size D1 D2 Nominal Pressure Nominal Pressure t1 t2
A 5K 10K 5K 10K
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
Dimension Charts
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(3) Dimension in brackets are applicable for TOMBO No.9010-NA-A-6/-NA-A-8.
104
For JIS Flanges NAFLON PTFE Cushion Gasket (Outer periphery seald)
TM
(TOMBO No.9010-NA-R-AS)
Ñ
D2 D2
D1 D1
t2 t1 t2 t1
D3 D3
D4 D4
Nominal D3 D4
Pipe Size D1 D2 Nominal Pressure Nominal Pressure t1 t2
A 5K 10K 5K 10K
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
Dimension Charts
Standard
105
JIS 10K Plastic Flanges Ebilon Gasket
TM
15 1/2B 93 18 5 26 41 70 4-15 53
20 3/4 98 22 5 32 47 75 4-15 58
25 1 123 30 5 38 53 90 4-19 68
Notes: (1) Applicable gaskets are Ebilon Gaskets TOMBO No.9013, 9013-D , 9013-EP and 9013-DEP.
(2) These dimensions are designed by NICHIAS Corporation to fit to plastic flanges based on JIS B 2210 10K.
(3) Applicable flanges are 10K plastic (PVC) flanges manufactured by Kubota Corp., Sekisui Chemical Co., Ltd.,
Asahi Organic Chemicals Industry Co., Ltd., etc.
(4) When these gaskets are used for JIS B 2210 and B 2220 flanges, the sealing section may be smaller than the flange inner diameter.
Dimension Charts
Standard
106
Electrical Insulation Bolt Kit
FOR JIS 10K Flanges
(TOMBO No.9910/9910H, TOMBO No.9011-NA-E5)
Ñ Ñ
Metal Insulation
t t3
d3
d1 d1 D5
d2 D2 d2 D2
rs t3
L d3
H t2 t1 D5
*The size of TOMBO No.9910 is the same as that of TOMBO No.9910-H except for "t" that stands for the thickness of insulating sleeve.
*If service temperature is over 150℃, TOMBO No.9910-H/9007-LC should be used. Please consult with us about the size of the TOMBO No.9007-LC.
107
Electrical Insulation Bolt Kit
FOR JIS 20K Flanges
(TOMBO No.9910/9910H, TOMBO No.9011-NA-E5)
Ñ Ñ
Metal Insulation
t t3
d3
d1 d1 D5
d2 D2 d2 D2
rs t3
L d3
H t2 t1 D5
108
Gaskets
INDEX
■NUMERICAL INDEX
TOMBO No. Product Name Page TOMBO No. Product Name Page
1000∼ 9000∼
2000∼
6000∼
NUMERICAL INDEX
110
■ALPHABETICAL INDEX
Product Name TOMBO No. Page Product Name TOMBO No. Page
A N
Anti-corrosion Paste 9120 60 NA Beater Sheet 6526 59
Aqua-tight Paste 9105 60 NA Corrugated Metal Jacketed Gasket 1861 37
NA Corrugated Metal Jacketed Gasket for High-temperature Applications 1861-FI 37
B NA Gasket Tape 1364 55
Brigeman Gasket 1850 32 NA Gasket with core 1378 54
BX Ring Gasket 1850-BX 32 NA Manhole Gasket 1374 54
NA Manhole Gasket (Treated with graphite) 1374-G 54
C NA Metal Jacketed Gasket 1841 37
CLINSIL-Brown 1995 7 NA Metal Jacketed Gasket for High-temperature Applications 1841-FI 37
CLINSIL-NF 1991-NF 8 NA Tadpole Gasket Tape 1368 55
CLINSIL-Super 1993 7 NA Tadpole Gasket Tape (Finished with graphite)1368-G 55
CLINSIL-Top 1120 6 NA Vortex Gasket 1804-NA Series 14
CLINSIL-UF 1938 8 NAFLON FD Gasket 9007-FD 44
Cloth Reinforced Rubber Cut Gasket 1051 56 NAFLON Manhole Gasket 9094 54
CMGC Gasket 37 NAFLON Paste 9400 61
NAFLON PFA Covered Rubber O-Ring 9022-PFA 52
D NAFLON PFA Gasket 9007-LP 45
Delta Gasket 1850-D 32 NAFLON PTFE Covered Rubber O-Ring 9022-A 52
Double Cone Gasket 1850 32 NAFLON PTFE Cushion Gasket 9010 46-49
NAFLON PTFE Cut Gasket 9007 42
E NAFLON PTFE Electrical Insulation Bolt Kit 9910-H 50
Ebilon Gasket (PTFE Jacketed) 9013 57 NAFLON PTFE Glass Fiber Filled Cut Gasket 9007-G20 42
Ebilon Gasket (PTFE Jacketed) for Electrolytic Cells 9013-D 57 NAFLON PTFE Low Creep Gasket 9007-LC 43
Ebilon Gasket (Solid Rubber) 9013-EP 57 NAFLON PTFE O-Ring 9028 52
Ebilon Gasket (Solid Rubber) for Electrolytic Cells 9013-DEP 57 NAFLON PTFE Special Filler Filled Cut Gasket 9007-SC 43
Electrical Insulation Gasket 9010-NA-E5 51 NAFLON PTFE Special Filler Filled Cut Gasket (Soft) 9007-GL 44
NAFLON PVDF Electrical Insulation Bolt Kit 9910 50
F NAFLON SP Packing 9037 52
FF Manhole Gasket 1400-TH 54 NAFLON Vortex Gasket 9090 Series 15
FF Manhole Gasket (Treated with graphite) 1400-THG 54 NICHIAS Soft Seal 9096 52
G O
Graseal Gasket 1200 40 Octagonal Ring Joint Gasket 1850-C 31
Graseal Gasket MI-A 1210-A 40 Oil-tight Paste 9106 60
Graseal Gasket PM 1215 40 Oval Ring Joint Gasket 1850-V 31
Graseal Gasket PM-A 1215-A 40
Graseal Gasket Tape (Crinkled) 1221 41 P
Graseal Gasket Tape (Plain) 1220 41 Plain Metal Gasket 1850-P 30
Graseal Vortex Gasket 1804-GR Series 14 PTFE Grease 9401 61
Graseal Vortex Gasket for Aluminum Flanges 1809-AL Series 17
Graseal Vortex Gasket L 1809 Series 17 R
Rubber Cut Gasket 1050 56
H Rubber O-Ring 2670 56
Heat Exchanger Gasket 38 RX Ring Gasket 1850-RX 32
Heat Exchanger Vortex Gasket with Pass Ribs 18
S
I Saniclean Gasket 9014 58
Irregular-shape Vortex Gasket 18 Serrated Metal Gasket 1890 30
Special Construction Vortex Gasket 19
L Standard Type Metal O-Seal 9200P 34
Lens type Gasket 1850-L 32 Super Manhole Gasket-ST 1400-ST 54
M V
Metakote 1600 59 Vent Hole Type Metal O-Seal 9200V 34
Metafoam 1608 59 Vermosul Sheet-P 6750-P 59
Metal Jacketed Gaskets with Graseal Tape 38 Vortex Gasket-GH 1806-GH Series 16
Metal O-Ring 1850-O 32 Vortex Gasket-GM 1806-GM Series 16
NUMERICAL INDEX
111
Printed in Japan on Recycled paper E03-0901-01-FT-BU-RE-0703