Professional Documents
Culture Documents
FEATURES
High Maximum Input Voltage Up to 30V
Low Dropout Voltage 0.2V typ. at Io=0.5A
Output Current Io(max.)=1.0A
ON/OFF Control
OFF Control Quiescent Current 1 A max.
Internal Short Circuit Current Limit
Internal Overvoltage Protection
Internal Thermal Overload Protection
Bipolar Technology
Package Outline TO-252-5
PIN CONFIGURATION
5 GND
4 NC
3 3 VOUT
2 ON/OFF CONTROL
1 VIN
NJM2386ADL3
BLOCK DIAGRAM
VIN V OUT
Overvoltage
CONTROL Protection
Bandgap
Reference
Thermal Current
Protection Limit
GND
Ver.2016-04-08 -1-
NJM2386A
OUTPUT VOLTAGE RANK LIST
Device Name VOUT Device Name VOUT
NJM2386ADL3-33 3.3V NJM2386ADL3-10 10.0V
NJM2386ADL3-05 5.0V NJM2386ADL3-12 12.0V
NJM2386ADL3-06 6.0V
NJM2386ADL3-08 8.0V
NJM2386ADL3-09 9.0V
-2- Ver.2016-04-08
NJM2386A
THERMAL CHARACTERISTICS
PARAMETER SYMBOL VALUE UNIT
Junction-to-Ambient 105 (*5)
ja C/W
thermal resistance 40 (*6)
Junction-to-Top of package 17 (*5)
jt C/W
characterization parameter 12 (*6)
2
(*5): Mounted on glass epoxy board. (76.2 114.3 1.6mm:based on EIA/JDEC standard size, 2Layers, Cu area 100mm )
(*6): Mounted on glass epoxy board. (76.2 114.3 1.6mm:based on EIA/JDEC standard, 4Layers)
(For 4Layers: Applying 74.2 74.2mm inner Cu area and a thermal via hole to a board based on JEDEC standard JESD51-5)
NJM2386ADL3 PowerDissipation
(Topr=-40~+85°C,Tj=150°C)
3500
3000
on 4 layers board
Power Dissipation P D(mW)
2500
2000
1000
500
0
-50 -25 0 25 50 75 100
Temperature : Ta(°C)
Ver.2016-04-08 -3-
NJM2386A
TEST CIRCUIT
Standard Test Circuit
A 1 3
NJM2386A
IQ/IQOFF
A Io
2 5 4
VIN + +
V Vo
A ICONT
22μF RL
0.33μF VCONT
-4- Ver.2016-04-08
NJM2386A
TYPICAL APPLICATION
In the case where ON/OFF Control is not required:
Rc
CONTROL
GND
0. 33μF
NJM2386A 22μF
Rc
CONTROL
GND
*In the case of using a resistance "Rc" between VIN and control.
If this resistor is inserted, it can reduce the control current when the control voltage is high.
The applied voltage to control pin should set to consider voltage drop through the resistor “Rc” and the minimum
control voltage for ON-state.
The VCONT (ON) and ICONT have temperature dependence as shown in the "Control Current vs. Temperature" and "
Control Voltage vs. Temperature" characteristics. Therefore, the resistance "Rc" should be selected to consider the
temperature characteristics.
Ver.2016-04-08 -5-
NJM2386A
*Output Capacitor CO
Output capacitor (CO) will be required for a phase compensation of the internal error amplifier.
The capacitance and the equivalent series resistance (ESR) influence to stable operation of the regulator.
Use of a smaller CO may cause excess output noise or oscillation of the regulator due to lack of the phase
compensation.
On the other hand, Use of a larger CO reduces output noise and ripple output, and also improves output
transient response when rapid load change.
Therefore, use the recommended CO value (refer to conditions of ELECTRIC CHARACTERISTIC) or larger
and should connect between GND and VOUT as shortest path as possible for stable operation
In addition, Please choose an appropriate capacitor in considering varied characteristics of capacitor (a frequency
characteristic, a temperature characteristic, and so on) when selecting CO.
-6- Ver.2016-04-08
NJM2386A
TYPICALCHARACTERISTICS
NJM2386A_5.0V NJM2386A_5.0V
Output Voltage vs. Input Voltage Output Voltage vs. Output Current
6 6 6
o
@:Ta=25 C
Co=22 F
5 5
5.5
V IN=Vo+1V 4
VIN=35V
5 3 3
2 VIN=Vo+12V 2
Io=0A
4.5
Io=0.5A
1 1
Io=1A
o
@:Ta=25 C
Co=22 F
4 0 0
4 4.5 5 5.5 6 0 0.5
500 1
1000 1.5
1500 2
2000 2.5
2500
Input Voltage : VIN(V) Output Current : Io(A)
NJM2386A_5.0 NJM2386A_5.0V
Ground Pin Current vs. Output Current Dropout Voltage vs. Output Current
40 1
o
o @:Ta=25 C
@:Ta=25 C
Co=22 F(Ceramic)
VIN=6V
35
Co=22 F
0.8
Ground Pin Current : GI ND (mA)
30
Dropout Voltage:dVI-O (V)
25
0.6
20
0.4
15
10
0.2
0 0
0 0.5 1 1.5 0 0.5 1 1.5
Output Current : IO(A) Output Current:Io(A)
NJM2386A_5.0V NJM2386A_5.0V
Control Current vs. Control Voltage Output Voltage vs. Control Voltage
100 6
o o
@:Ta=25 C @:Ta=25 C
VIN=6V V IN=6V
Co=22 F 5 Co=22 F
80 Io=0.5A Io=0.5A
( A)
4
Cont
60
Control Current : I
Rc=0
3 Rc=0
40
2
Rc=50k
Rc=50k Rc=100k
20
1
Rc=100k
0 0
0 1 2 3 0 0.5 1 1.5 2 2.5
Control Voltage : V (V) Control Voltage : V (V)
Cont Cont
Ver.2016-04-08 -7-
NJM2386A
TYPICALCHARACTERISTICS
NJM2386A_5.0V NJM2386A_5.0V
Load Regulation vs. Output Current Peak Output Current vs. Input Voltage
3 3
o
@:Ta=25 C
Co=22 F
2 2.5
Load Regulation : dVo-Io(%/A)
0 1.5
-1 1
-2 0.5
o
@:Ta=25 C
VIN=6.0V
Co=22 F
-3 0
0 0.5 1 1.5 5 10 15 20 25 30 35
Output Current : Io(A) Input Voltage : VIN(V)
NJM2386A_5.0V
Quiescent Current vs. Input Voltage NJM2386A_5.0V
50 Output Noise Voltage vs. Output Current
o 500
@:Ta=25 C
o
Output is open. @:Ta=25 C
Co=22 F V IN=6V
40 including Icont LPF:80kHz
400 Co=22 F
Output Noise Voltage : Vn( Vrms)
Quiescent Current : IQ (mA)
30
300
20
200
10
100
0 0
0 5 10 15 20 25 30 35 1
1u
0.001 10
0.01 100
0.1 1m
1 10m
10 100m
100 1
1000
Input Voltage : VIN(V) Output Current : Io(A)
NJM2386A_5.0V NJM2386A_5.0V
Ripple Rejection Ratio vs. Frequency Ripple Rejection Ratio vs. Output Current
100 100
90 90
Ripple Rejection Ratio: RR (dB)
Ripple Rejection Ratio: RR (dB)
80 80
Io=0A
Io=0.1A
70 70
60 60
50 50
Io=1.0A Io=0.5A
40 40
@:Ta=25 oC
o V IN=7V
@:Ta=25 C
eIN=500mVrms
30 V IN=7V 30
f=120Hz
eIN=500mVrms
Co=22 F
Co=22 F
20 20
10
10 100
100 1k
1000 10k
104 100k
105 0.001
1
1u 10
0.01 100
0.1 1m
1 10m
10 100m
100 11000
Frequency : f (Hz) Output Current : Io(A)
-8- Ver.2016-04-08
NJM2386A
TYPICALCHARACTERISTICS
NJM2386A_5.0V NJM2386A_5.0V
Dropout Voltage vs. Tem perature Control Voltage vs. Temperature
1 2
@:VIN=6V
@:Co=22 F
Io=0.5A
Io=0.5A
Co=22 F
0.8
0.6
0.4
0.5
0.2
0 0
-50 0 50 100 150 -50 0 50 100 150
o o
Temperature : Ta ( C) Temperature : Ta ( C)
NJM2386A_5.0V NJM2386A_5.0V
Output Voltage vs. Temperature Output Peak Current vs. Temperature
5.2 2000
@:VIN=6V
Io=0.5A
Co=22 F
Output Peak Current : Io_peak (mA)
5.1 1500
Output Voltage : Vo(V)
5 1000
4.9 500
@:V IN=6.0V
Co=22 F
4.8 0
-50 0 50 100 150 -50 0 50 100 150
o o
Temperature : Ta ( C) Temperature : Ta ( C)
NJM2386A_5.0V
Quiescent Current vs. Input Voltage
5
4
Quiescent Current : IQ (mA)
1
@:V IN=6V
Output is open.
Co=22 F
Vcont=2.7V
0
-50 0 50 100 150
o
Temperature : Ta ( C)
Ver.2016-04-08 -9-
NJM2386A
TYPICALCHARACTERISTICS
NJM2386A_5.0V
NJM2386A_5.0V Load Regulation vs. Temperature
Line Regulation vs. Tem perature 1.5
0.1
@:VIN=6V
@:V IN=6-22V Io=0-1A
Io=0.5A Co=22 F
Co=22 F
0.05
1
0.5
-0.05
-0.1 0
-50 0 50 100 150 -50 0 50 100 150
o o
Temperature : Ta ( C) Temperature : Ta ( C)
NJM2386A_5.0V
Output Voltage vs. Temperature NJM2386A_5.0V
6 Short Circuit Current vs. Temperature
500
@: V IN=6V
Co=22 F
5 Output is short to ground.
400
Short Circuit Current : Isc (mA)
Output Voltage : Vo(V)
300
200
2
100
1
@:VIN=6.0V
Io=500mA
Co=22 F
0 0
-50 0 50 100 150 200 -50 0 50 100 150
o o
Temperature : Ta ( C) Temperature : Ta ( C)
- 10 - Ver.2016-04-08
NJM2386A
TYPICALCHARACTERISTICS
NJM2386A_5.0V NJM2386A_5.0V
ON/OFF Transient Response without Load ON/OFF Transient Response
14 10 14 10
12 5 12 5
Control Voltage Control Voltage
10 0
4 -15 4 -15
-2 -30 -2 -30
0 1 2 3 4 5 0 4 8 12 16 20
Time : t [S] Time : t [mS]
NJM2386A_5.0V NJM2386A_5.0V
Input Transient Response Load Transient Response
5.1 8 6 600
[CAUTION]
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
of the product and not intended for the
guarantee or permission of any right including
the industrial rights.
Ver.2016-04-08 - 11 -